migrate ucc_geth to use the common phylib code.
There are several side effects from doing this:
o deprecate 'interface' property specification present
in some old device tree source files in
favour of a split 'max-speed' and 'interface-type'
description to appropriately match definitions
in include/linux/phy.h. Note that 'interface' property
is still honoured if max-speed or interface-type
are not present (backward compatible).
o compile-time CONFIG_UGETH_HAS_GIGA is eliminated
in favour of probe time speed derivation logic.
o adjust_link streamlined to only operate on maccfg2
and upsmr.r10m, instead of reapplying static initial
values related to the interface-type.
o Addition of UEC MDIO of_platform driver requires
platform code add 'mdio' type to id list
prior to calling of_platform_bus_probe (separate patch).
o ucc_struct_init introduced to reduce ucc_geth_startup
complexity.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
bool "Transmit on Demond support"
depends on UCC_GETH
-config UGETH_HAS_GIGA
- bool
- depends on UCC_GETH && PPC_MPC836x
-
config MV643XX_ETH
tristate "MV-643XX Ethernet support"
depends on MOMENCO_OCELOT_C || MOMENCO_JAGUAR_ATX || MV64360 || MOMENCO_OCELOT_3 || (PPC_MULTIPLATFORM && PPC32)
gianfar_sysfs.o
obj-$(CONFIG_UCC_GETH) += ucc_geth_driver.o
-ucc_geth_driver-objs := ucc_geth.o ucc_geth_phy.o
+ucc_geth_driver-objs := ucc_geth.o ucc_geth_mii.o
#
# link order important here
#include <linux/fsl_devices.h>
#include <linux/ethtool.h>
#include <linux/mii.h>
+#include <linux/phy.h>
#include <linux/workqueue.h>
#include <asm/of_platform.h>
#include <asm/ucc_fast.h>
#include "ucc_geth.h"
-#include "ucc_geth_phy.h"
+#include "ucc_geth_mii.h"
#undef DEBUG
.bd_mem_part = MEM_PART_SYSTEM,
.rtsm = UCC_FAST_SEND_IDLES_BETWEEN_FRAMES,
.max_rx_buf_length = 1536,
-/* FIXME: should be changed in run time for 1G and 100M */
-#ifdef CONFIG_UGETH_HAS_GIGA
- .urfs = UCC_GETH_URFS_GIGA_INIT,
- .urfet = UCC_GETH_URFET_GIGA_INIT,
- .urfset = UCC_GETH_URFSET_GIGA_INIT,
- .utfs = UCC_GETH_UTFS_GIGA_INIT,
- .utfet = UCC_GETH_UTFET_GIGA_INIT,
- .utftt = UCC_GETH_UTFTT_GIGA_INIT,
-#else
+ /* adjusted at startup if max-speed 1000 */
.urfs = UCC_GETH_URFS_INIT,
.urfet = UCC_GETH_URFET_INIT,
.urfset = UCC_GETH_URFSET_INIT,
.utfs = UCC_GETH_UTFS_INIT,
.utfet = UCC_GETH_UTFET_INIT,
.utftt = UCC_GETH_UTFTT_INIT,
-#endif
.ufpt = 256,
.mode = UCC_FAST_PROTOCOL_MODE_ETHERNET,
.ttx_trx = UCC_FAST_GUMR_TRANSPARENT_TTX_TRX_NORMAL,
}
}
-static int get_interface_details(enum enet_interface enet_interface,
- enum enet_speed *speed,
- int *r10m,
- int *rmm,
- int *rpm,
- int *tbi, int *limited_to_full_duplex)
-{
- /* Analyze enet_interface according to Interface Mode
- Configuration table */
- switch (enet_interface) {
- case ENET_10_MII:
- *speed = ENET_SPEED_10BT;
- break;
- case ENET_10_RMII:
- *speed = ENET_SPEED_10BT;
- *r10m = 1;
- *rmm = 1;
- break;
- case ENET_10_RGMII:
- *speed = ENET_SPEED_10BT;
- *rpm = 1;
- *r10m = 1;
- *limited_to_full_duplex = 1;
- break;
- case ENET_100_MII:
- *speed = ENET_SPEED_100BT;
- break;
- case ENET_100_RMII:
- *speed = ENET_SPEED_100BT;
- *rmm = 1;
- break;
- case ENET_100_RGMII:
- *speed = ENET_SPEED_100BT;
- *rpm = 1;
- *limited_to_full_duplex = 1;
- break;
- case ENET_1000_GMII:
- *speed = ENET_SPEED_1000BT;
- *limited_to_full_duplex = 1;
- break;
- case ENET_1000_RGMII:
- *speed = ENET_SPEED_1000BT;
- *rpm = 1;
- *limited_to_full_duplex = 1;
- break;
- case ENET_1000_TBI:
- *speed = ENET_SPEED_1000BT;
- *tbi = 1;
- *limited_to_full_duplex = 1;
- break;
- case ENET_1000_RTBI:
- *speed = ENET_SPEED_1000BT;
- *rpm = 1;
- *tbi = 1;
- *limited_to_full_duplex = 1;
- break;
- default:
- return -EINVAL;
- break;
- }
-
- return 0;
-}
-
static struct sk_buff *get_new_skb(struct ucc_geth_private *ugeth, u8 *bd)
{
struct sk_buff *skb = NULL;
ugeth_info("hafdup : addr - 0x%08x, val - 0x%08x",
(u32) & ugeth->ug_regs->hafdup,
in_be32(&ugeth->ug_regs->hafdup));
- ugeth_info("miimcfg : addr - 0x%08x, val - 0x%08x",
- (u32) & ugeth->ug_regs->miimng.miimcfg,
- in_be32(&ugeth->ug_regs->miimng.miimcfg));
- ugeth_info("miimcom : addr - 0x%08x, val - 0x%08x",
- (u32) & ugeth->ug_regs->miimng.miimcom,
- in_be32(&ugeth->ug_regs->miimng.miimcom));
- ugeth_info("miimadd : addr - 0x%08x, val - 0x%08x",
- (u32) & ugeth->ug_regs->miimng.miimadd,
- in_be32(&ugeth->ug_regs->miimng.miimadd));
- ugeth_info("miimcon : addr - 0x%08x, val - 0x%08x",
- (u32) & ugeth->ug_regs->miimng.miimcon,
- in_be32(&ugeth->ug_regs->miimng.miimcon));
- ugeth_info("miimstat : addr - 0x%08x, val - 0x%08x",
- (u32) & ugeth->ug_regs->miimng.miimstat,
- in_be32(&ugeth->ug_regs->miimng.miimstat));
- ugeth_info("miimmind : addr - 0x%08x, val - 0x%08x",
- (u32) & ugeth->ug_regs->miimng.miimind,
- in_be32(&ugeth->ug_regs->miimng.miimind));
ugeth_info("ifctl : addr - 0x%08x, val - 0x%08x",
(u32) & ugeth->ug_regs->ifctl,
in_be32(&ugeth->ug_regs->ifctl));
return 0;
}
-static int init_mac_duplex_mode(int full_duplex,
- int limited_to_full_duplex,
- volatile u32 *maccfg2_register)
-{
- u32 value = 0;
-
- /* some interfaces must work in full duplex mode */
- if ((full_duplex == 0) && (limited_to_full_duplex == 1))
- return -EINVAL;
-
- value = in_be32(maccfg2_register);
-
- if (full_duplex)
- value |= MACCFG2_FDX;
- else
- value &= ~MACCFG2_FDX;
-
- out_be32(maccfg2_register, value);
- return 0;
-}
-
static int init_check_frame_length_mode(int length_check,
volatile u32 *maccfg2_register)
{
return 0;
}
-static int init_mii_management_configuration(int reset_mgmt,
- int preamble_supress,
- volatile u32 *miimcfg_register,
- volatile u32 *miimind_register)
-{
- unsigned int timeout = PHY_INIT_TIMEOUT;
- u32 value = 0;
-
- value = in_be32(miimcfg_register);
- if (reset_mgmt) {
- value |= MIIMCFG_RESET_MANAGEMENT;
- out_be32(miimcfg_register, value);
- }
-
- value = 0;
-
- if (preamble_supress)
- value |= MIIMCFG_NO_PREAMBLE;
-
- value |= UCC_GETH_MIIMCFG_MNGMNT_CLC_DIV_INIT;
- out_be32(miimcfg_register, value);
-
- /* Wait until the bus is free */
- while ((in_be32(miimind_register) & MIIMIND_BUSY) && timeout--)
- cpu_relax();
-
- if (timeout <= 0) {
- ugeth_err("%s: The MII Bus is stuck!", __FUNCTION__);
- return -ETIMEDOUT;
- }
-
- return 0;
-}
-
static int init_rx_parameters(int reject_broadcast,
int receive_short_frames,
int promiscuous, volatile u32 *upsmr_register)
struct ucc_geth_info *ug_info;
struct ucc_geth *ug_regs;
struct ucc_fast *uf_regs;
- enum enet_speed speed;
- int ret_val, rpm = 0, tbi = 0, r10m = 0, rmm =
- 0, limited_to_full_duplex = 0;
- u32 upsmr, maccfg2, utbipar, tbiBaseAddress;
+ int ret_val;
+ u32 upsmr, maccfg2, tbiBaseAddress;
u16 value;
ugeth_vdbg("%s: IN", __FUNCTION__);
ug_regs = ugeth->ug_regs;
uf_regs = ugeth->uccf->uf_regs;
- /* Analyze enet_interface according to Interface Mode Configuration
- table */
- ret_val =
- get_interface_details(ug_info->enet_interface, &speed, &r10m, &rmm,
- &rpm, &tbi, &limited_to_full_duplex);
- if (ret_val != 0) {
- ugeth_err
- ("%s: half duplex not supported in requested configuration.",
- __FUNCTION__);
- return ret_val;
- }
-
/* Set MACCFG2 */
maccfg2 = in_be32(&ug_regs->maccfg2);
maccfg2 &= ~MACCFG2_INTERFACE_MODE_MASK;
- if ((speed == ENET_SPEED_10BT) || (speed == ENET_SPEED_100BT))
+ if ((ugeth->max_speed == SPEED_10) ||
+ (ugeth->max_speed == SPEED_100))
maccfg2 |= MACCFG2_INTERFACE_MODE_NIBBLE;
- else if (speed == ENET_SPEED_1000BT)
+ else if (ugeth->max_speed == SPEED_1000)
maccfg2 |= MACCFG2_INTERFACE_MODE_BYTE;
maccfg2 |= ug_info->padAndCrc;
out_be32(&ug_regs->maccfg2, maccfg2);
/* Set UPSMR */
upsmr = in_be32(&uf_regs->upsmr);
upsmr &= ~(UPSMR_RPM | UPSMR_R10M | UPSMR_TBIM | UPSMR_RMM);
- if (rpm)
+ if ((ugeth->phy_interface == PHY_INTERFACE_MODE_RMII) ||
+ (ugeth->phy_interface == PHY_INTERFACE_MODE_RGMII) ||
+ (ugeth->phy_interface == PHY_INTERFACE_MODE_RGMII_ID) ||
+ (ugeth->phy_interface == PHY_INTERFACE_MODE_RTBI)) {
upsmr |= UPSMR_RPM;
- if (r10m)
- upsmr |= UPSMR_R10M;
- if (tbi)
+ switch (ugeth->max_speed) {
+ case SPEED_10:
+ upsmr |= UPSMR_R10M;
+ /* FALLTHROUGH */
+ case SPEED_100:
+ if (ugeth->phy_interface != PHY_INTERFACE_MODE_RTBI)
+ upsmr |= UPSMR_RMM;
+ }
+ }
+ if ((ugeth->phy_interface == PHY_INTERFACE_MODE_TBI) ||
+ (ugeth->phy_interface == PHY_INTERFACE_MODE_RTBI)) {
upsmr |= UPSMR_TBIM;
- if (rmm)
- upsmr |= UPSMR_RMM;
+ }
out_be32(&uf_regs->upsmr, upsmr);
- /* Set UTBIPAR */
- utbipar = in_be32(&ug_regs->utbipar);
- utbipar &= ~UTBIPAR_PHY_ADDRESS_MASK;
- if (tbi)
- utbipar |=
- (ug_info->phy_address +
- ugeth->ug_info->uf_info.
- ucc_num) << UTBIPAR_PHY_ADDRESS_SHIFT;
- else
- utbipar |=
- (0x10 +
- ugeth->ug_info->uf_info.
- ucc_num) << UTBIPAR_PHY_ADDRESS_SHIFT;
- out_be32(&ug_regs->utbipar, utbipar);
-
/* Disable autonegotiation in tbi mode, because by default it
comes up in autonegotiation mode. */
/* Note that this depends on proper setting in utbipar register. */
- if (tbi) {
+ if ((ugeth->phy_interface == PHY_INTERFACE_MODE_TBI) ||
+ (ugeth->phy_interface == PHY_INTERFACE_MODE_RTBI)) {
tbiBaseAddress = in_be32(&ug_regs->utbipar);
tbiBaseAddress &= UTBIPAR_PHY_ADDRESS_MASK;
tbiBaseAddress >>= UTBIPAR_PHY_ADDRESS_SHIFT;
- value =
- ugeth->mii_info->mdio_read(ugeth->dev, (u8) tbiBaseAddress,
- ENET_TBI_MII_CR);
+ value = ugeth->phydev->bus->read(ugeth->phydev->bus,
+ (u8) tbiBaseAddress, ENET_TBI_MII_CR);
value &= ~0x1000; /* Turn off autonegotiation */
- ugeth->mii_info->mdio_write(ugeth->dev, (u8) tbiBaseAddress,
- ENET_TBI_MII_CR, value);
- }
-
- ret_val = init_mac_duplex_mode(1,
- limited_to_full_duplex,
- &ug_regs->maccfg2);
- if (ret_val != 0) {
- ugeth_err
- ("%s: half duplex not supported in requested configuration.",
- __FUNCTION__);
- return ret_val;
+ ugeth->phydev->bus->write(ugeth->phydev->bus,
+ (u8) tbiBaseAddress, ENET_TBI_MII_CR, value);
}
init_check_frame_length_mode(ug_info->lengthCheckRx, &ug_regs->maccfg2);
* function converts those variables into the appropriate
* register values, and can bring down the device if needed.
*/
+
static void adjust_link(struct net_device *dev)
{
struct ucc_geth_private *ugeth = netdev_priv(dev);
struct ucc_geth *ug_regs;
- u32 tempval;
- struct ugeth_mii_info *mii_info = ugeth->mii_info;
+ struct ucc_fast *uf_regs;
+ struct phy_device *phydev = ugeth->phydev;
+ unsigned long flags;
+ int new_state = 0;
ug_regs = ugeth->ug_regs;
+ uf_regs = ugeth->uccf->uf_regs;
- if (mii_info->link) {
+ spin_lock_irqsave(&ugeth->lock, flags);
+
+ if (phydev->link) {
+ u32 tempval = in_be32(&ug_regs->maccfg2);
+ u32 upsmr = in_be32(&uf_regs->upsmr);
/* Now we make sure that we can be in full duplex mode.
* If not, we operate in half-duplex mode. */
- if (mii_info->duplex != ugeth->oldduplex) {
- if (!(mii_info->duplex)) {
- tempval = in_be32(&ug_regs->maccfg2);
+ if (phydev->duplex != ugeth->oldduplex) {
+ new_state = 1;
+ if (!(phydev->duplex))
tempval &= ~(MACCFG2_FDX);
- out_be32(&ug_regs->maccfg2, tempval);
-
- ugeth_info("%s: Half Duplex", dev->name);
- } else {
- tempval = in_be32(&ug_regs->maccfg2);
+ else
tempval |= MACCFG2_FDX;
- out_be32(&ug_regs->maccfg2, tempval);
-
- ugeth_info("%s: Full Duplex", dev->name);
- }
-
- ugeth->oldduplex = mii_info->duplex;
+ ugeth->oldduplex = phydev->duplex;
}
- if (mii_info->speed != ugeth->oldspeed) {
- switch (mii_info->speed) {
- case 1000:
- ugeth->ug_info->enet_interface = ENET_1000_RGMII;
- break;
- case 100:
- ugeth->ug_info->enet_interface = ENET_100_RGMII;
+ if (phydev->speed != ugeth->oldspeed) {
+ new_state = 1;
+ switch (phydev->speed) {
+ case SPEED_1000:
+ tempval = ((tempval &
+ ~(MACCFG2_INTERFACE_MODE_MASK)) |
+ MACCFG2_INTERFACE_MODE_BYTE);
break;
- case 10:
- ugeth->ug_info->enet_interface = ENET_10_RGMII;
+ case SPEED_100:
+ case SPEED_10:
+ tempval = ((tempval &
+ ~(MACCFG2_INTERFACE_MODE_MASK)) |
+ MACCFG2_INTERFACE_MODE_NIBBLE);
+ /* if reduced mode, re-set UPSMR.R10M */
+ if ((ugeth->phy_interface == PHY_INTERFACE_MODE_RMII) ||
+ (ugeth->phy_interface == PHY_INTERFACE_MODE_RGMII) ||
+ (ugeth->phy_interface == PHY_INTERFACE_MODE_RGMII_ID) ||
+ (ugeth->phy_interface == PHY_INTERFACE_MODE_RTBI)) {
+ if (phydev->speed == SPEED_10)
+ upsmr |= UPSMR_R10M;
+ else
+ upsmr &= ~(UPSMR_R10M);
+ }
break;
default:
- ugeth_warn
- ("%s: Ack! Speed (%d) is not 10/100/1000!",
- dev->name, mii_info->speed);
+ if (netif_msg_link(ugeth))
+ ugeth_warn(
+ "%s: Ack! Speed (%d) is not 10/100/1000!",
+ dev->name, phydev->speed);
break;
}
- adjust_enet_interface(ugeth);
-
- ugeth_info("%s: Speed %dBT", dev->name,
- mii_info->speed);
-
- ugeth->oldspeed = mii_info->speed;
+ ugeth->oldspeed = phydev->speed;
}
+ out_be32(&ug_regs->maccfg2, tempval);
+ out_be32(&uf_regs->upsmr, upsmr);
+
if (!ugeth->oldlink) {
- ugeth_info("%s: Link is up", dev->name);
+ new_state = 1;
ugeth->oldlink = 1;
- netif_carrier_on(dev);
netif_schedule(dev);
}
- } else {
- if (ugeth->oldlink) {
- ugeth_info("%s: Link is down", dev->name);
+ } else if (ugeth->oldlink) {
+ new_state = 1;
ugeth->oldlink = 0;
ugeth->oldspeed = 0;
ugeth->oldduplex = -1;
- netif_carrier_off(dev);
- }
}
+
+ if (new_state && netif_msg_link(ugeth))
+ phy_print_status(phydev);
+
+ spin_unlock_irqrestore(&ugeth->lock, flags);
}
/* Configure the PHY for dev.
*/
static int init_phy(struct net_device *dev)
{
- struct ucc_geth_private *ugeth = netdev_priv(dev);
- struct phy_info *curphy;
- struct ucc_mii_mng *mii_regs;
- struct ugeth_mii_info *mii_info;
- int err;
+ struct ucc_geth_private *priv = netdev_priv(dev);
+ struct phy_device *phydev;
+ char phy_id[BUS_ID_SIZE];
- mii_regs = &ugeth->ug_regs->miimng;
+ priv->oldlink = 0;
+ priv->oldspeed = 0;
+ priv->oldduplex = -1;
- ugeth->oldlink = 0;
- ugeth->oldspeed = 0;
- ugeth->oldduplex = -1;
+ snprintf(phy_id, BUS_ID_SIZE, PHY_ID_FMT, priv->ug_info->mdio_bus,
+ priv->ug_info->phy_address);
- mii_info = kmalloc(sizeof(struct ugeth_mii_info), GFP_KERNEL);
+ phydev = phy_connect(dev, phy_id, &adjust_link, 0, priv->phy_interface);
- if (NULL == mii_info) {
- ugeth_err("%s: Could not allocate mii_info", dev->name);
- return -ENOMEM;
+ if (IS_ERR(phydev)) {
+ printk("%s: Could not attach to PHY\n", dev->name);
+ return PTR_ERR(phydev);
}
- mii_info->mii_regs = mii_regs;
- mii_info->speed = SPEED_1000;
- mii_info->duplex = DUPLEX_FULL;
- mii_info->pause = 0;
- mii_info->link = 0;
-
- mii_info->advertising = (ADVERTISED_10baseT_Half |
+ phydev->supported &= (ADVERTISED_10baseT_Half |
ADVERTISED_10baseT_Full |
ADVERTISED_100baseT_Half |
- ADVERTISED_100baseT_Full |
- ADVERTISED_1000baseT_Full);
- mii_info->autoneg = 1;
-
- mii_info->mii_id = ugeth->ug_info->phy_address;
-
- mii_info->dev = dev;
+ ADVERTISED_100baseT_Full);
- mii_info->mdio_read = &read_phy_reg;
- mii_info->mdio_write = &write_phy_reg;
+ if (priv->max_speed == SPEED_1000)
+ phydev->supported |= ADVERTISED_1000baseT_Full;
- spin_lock_init(&mii_info->mdio_lock);
+ phydev->advertising = phydev->supported;
- ugeth->mii_info = mii_info;
-
- spin_lock_irq(&ugeth->lock);
-
- /* Set this UCC to be the master of the MII managment */
- ucc_set_qe_mux_mii_mng(ugeth->ug_info->uf_info.ucc_num);
-
- if (init_mii_management_configuration(1,
- ugeth->ug_info->
- miiPreambleSupress,
- &mii_regs->miimcfg,
- &mii_regs->miimind)) {
- ugeth_err("%s: The MII Bus is stuck!", dev->name);
- err = -1;
- goto bus_fail;
- }
-
- spin_unlock_irq(&ugeth->lock);
-
- /* get info for this PHY */
- curphy = get_phy_info(ugeth->mii_info);
-
- if (curphy == NULL) {
- ugeth_err("%s: No PHY found", dev->name);
- err = -1;
- goto no_phy;
- }
-
- mii_info->phyinfo = curphy;
-
- /* Run the commands which initialize the PHY */
- if (curphy->init) {
- err = curphy->init(ugeth->mii_info);
- if (err)
- goto phy_init_fail;
- }
+ priv->phydev = phydev;
return 0;
-
- phy_init_fail:
- no_phy:
- bus_fail:
- kfree(mii_info);
-
- return err;
}
+
#ifdef CONFIG_UGETH_TX_ON_DEMOND
static int ugeth_transmit_on_demand(struct ucc_geth_private *ugeth)
{
static void ucc_geth_stop(struct ucc_geth_private *ugeth)
{
struct ucc_geth *ug_regs = ugeth->ug_regs;
+ struct phy_device *phydev = ugeth->phydev;
u32 tempval;
ugeth_vdbg("%s: IN", __FUNCTION__);
ugeth_disable(ugeth, COMM_DIR_RX_AND_TX);
/* Tell the kernel the link is down */
- ugeth->mii_info->link = 0;
- adjust_link(ugeth->dev);
+ phy_stop(phydev);
/* Mask all interrupts */
out_be32(ugeth->uccf->p_ucce, 0x00000000);
tempval &= ~(MACCFG1_ENABLE_RX | MACCFG1_ENABLE_TX);
out_be32(&ug_regs->maccfg1, tempval);
- if (ugeth->ug_info->board_flags & FSL_UGETH_BRD_HAS_PHY_INTR) {
- /* Clear any pending interrupts */
- mii_clear_phy_interrupt(ugeth->mii_info);
-
- /* Disable PHY Interrupts */
- mii_configure_phy_interrupt(ugeth->mii_info,
- MII_INTERRUPT_DISABLED);
- }
-
free_irq(ugeth->ug_info->uf_info.irq, ugeth->dev);
- if (ugeth->ug_info->board_flags & FSL_UGETH_BRD_HAS_PHY_INTR) {
- free_irq(ugeth->ug_info->phy_interrupt, ugeth->dev);
- } else {
- del_timer_sync(&ugeth->phy_info_timer);
- }
-
ucc_geth_memclean(ugeth);
}
-static int ucc_geth_startup(struct ucc_geth_private *ugeth)
+static int ucc_struct_init(struct ucc_geth_private *ugeth)
{
- struct ucc_geth_82xx_address_filtering_pram *p_82xx_addr_filt;
- struct ucc_geth_init_pram *p_init_enet_pram;
- struct ucc_fast_private *uccf;
struct ucc_geth_info *ug_info;
struct ucc_fast_info *uf_info;
- struct ucc_fast *uf_regs;
- struct ucc_geth *ug_regs;
- int ret_val = -EINVAL;
- u32 remoder = UCC_GETH_REMODER_INIT;
- u32 init_enet_pram_offset, cecr_subblock, command, maccfg1;
- u32 ifstat, i, j, size, l2qt, l3qt, length;
- u16 temoder = UCC_GETH_TEMODER_INIT;
- u16 test;
- u8 function_code = 0;
- u8 *bd, *endOfRing;
- u8 numThreadsRxNumerical, numThreadsTxNumerical;
-
- ugeth_vdbg("%s: IN", __FUNCTION__);
+ int i;
ug_info = ugeth->ug_info;
uf_info = &ug_info->uf_info;
for (i = 0; i < ug_info->numQueuesTx; i++)
uf_info->uccm_mask |= (UCCE_TXBF_SINGLE_MASK << i);
/* Initialize the general fast UCC block. */
- if (ucc_fast_init(uf_info, &uccf)) {
+ if (ucc_fast_init(uf_info, &ugeth->uccf)) {
ugeth_err("%s: Failed to init uccf.", __FUNCTION__);
ucc_geth_memclean(ugeth);
return -ENOMEM;
}
- ugeth->uccf = uccf;
+
+ ugeth->ug_regs = (struct ucc_geth *) ioremap(uf_info->regs, sizeof(struct ucc_geth));
+
+ return 0;
+}
+
+static int ucc_geth_startup(struct ucc_geth_private *ugeth)
+{
+ struct ucc_geth_82xx_address_filtering_pram *p_82xx_addr_filt;
+ struct ucc_geth_init_pram *p_init_enet_pram;
+ struct ucc_fast_private *uccf;
+ struct ucc_geth_info *ug_info;
+ struct ucc_fast_info *uf_info;
+ struct ucc_fast *uf_regs;
+ struct ucc_geth *ug_regs;
+ int ret_val = -EINVAL;
+ u32 remoder = UCC_GETH_REMODER_INIT;
+ u32 init_enet_pram_offset, cecr_subblock, command, maccfg1;
+ u32 ifstat, i, j, size, l2qt, l3qt, length;
+ u16 temoder = UCC_GETH_TEMODER_INIT;
+ u16 test;
+ u8 function_code = 0;
+ u8 *bd, *endOfRing;
+ u8 numThreadsRxNumerical, numThreadsTxNumerical;
+
+ ugeth_vdbg("%s: IN", __FUNCTION__);
+ uccf = ugeth->uccf;
+ ug_info = ugeth->ug_info;
+ uf_info = &ug_info->uf_info;
+ uf_regs = uccf->uf_regs;
+ ug_regs = ugeth->ug_regs;
switch (ug_info->numThreadsRx) {
case UCC_GETH_NUM_OF_THREADS_1:
|| (ug_info->vlanOperationNonTagged !=
UCC_GETH_VLAN_OPERATION_NON_TAGGED_NOP);
- uf_regs = uccf->uf_regs;
- ug_regs = (struct ucc_geth *) (uccf->uf_regs);
- ugeth->ug_regs = ug_regs;
-
init_default_reg_vals(&uf_regs->upsmr,
&ug_regs->maccfg1, &ug_regs->maccfg2);
return IRQ_HANDLED;
}
-static irqreturn_t phy_interrupt(int irq, void *dev_id)
-{
- struct net_device *dev = (struct net_device *)dev_id;
- struct ucc_geth_private *ugeth = netdev_priv(dev);
-
- ugeth_vdbg("%s: IN", __FUNCTION__);
-
- /* Clear the interrupt */
- mii_clear_phy_interrupt(ugeth->mii_info);
-
- /* Disable PHY interrupts */
- mii_configure_phy_interrupt(ugeth->mii_info, MII_INTERRUPT_DISABLED);
-
- /* Schedule the phy change */
- schedule_work(&ugeth->tq);
-
- return IRQ_HANDLED;
-}
-
-/* Scheduled by the phy_interrupt/timer to handle PHY changes */
-static void ugeth_phy_change(struct work_struct *work)
-{
- struct ucc_geth_private *ugeth =
- container_of(work, struct ucc_geth_private, tq);
- struct net_device *dev = ugeth->dev;
- struct ucc_geth *ug_regs;
- int result = 0;
-
- ugeth_vdbg("%s: IN", __FUNCTION__);
-
- ug_regs = ugeth->ug_regs;
-
- /* Delay to give the PHY a chance to change the
- * register state */
- msleep(1);
-
- /* Update the link, speed, duplex */
- result = ugeth->mii_info->phyinfo->read_status(ugeth->mii_info);
-
- /* Adjust the known status as long as the link
- * isn't still coming up */
- if ((0 == result) || (ugeth->mii_info->link == 0))
- adjust_link(dev);
-
- /* Reenable interrupts, if needed */
- if (ugeth->ug_info->board_flags & FSL_UGETH_BRD_HAS_PHY_INTR)
- mii_configure_phy_interrupt(ugeth->mii_info,
- MII_INTERRUPT_ENABLED);
-}
-
-/* Called every so often on systems that don't interrupt
- * the core for PHY changes */
-static void ugeth_phy_timer(unsigned long data)
-{
- struct net_device *dev = (struct net_device *)data;
- struct ucc_geth_private *ugeth = netdev_priv(dev);
-
- schedule_work(&ugeth->tq);
-
- mod_timer(&ugeth->phy_info_timer, jiffies + PHY_CHANGE_TIME * HZ);
-}
-
-/* Keep trying aneg for some time
- * If, after GFAR_AN_TIMEOUT seconds, it has not
- * finished, we switch to forced.
- * Either way, once the process has completed, we either
- * request the interrupt, or switch the timer over to
- * using ugeth_phy_timer to check status */
-static void ugeth_phy_startup_timer(unsigned long data)
-{
- struct ugeth_mii_info *mii_info = (struct ugeth_mii_info *)data;
- struct ucc_geth_private *ugeth = netdev_priv(mii_info->dev);
- static int secondary = UGETH_AN_TIMEOUT;
- int result;
-
- /* Configure the Auto-negotiation */
- result = mii_info->phyinfo->config_aneg(mii_info);
-
- /* If autonegotiation failed to start, and
- * we haven't timed out, reset the timer, and return */
- if (result && secondary--) {
- mod_timer(&ugeth->phy_info_timer, jiffies + HZ);
- return;
- } else if (result) {
- /* Couldn't start autonegotiation.
- * Try switching to forced */
- mii_info->autoneg = 0;
- result = mii_info->phyinfo->config_aneg(mii_info);
-
- /* Forcing failed! Give up */
- if (result) {
- ugeth_err("%s: Forcing failed!", mii_info->dev->name);
- return;
- }
- }
-
- /* Kill the timer so it can be restarted */
- del_timer_sync(&ugeth->phy_info_timer);
-
- /* Grab the PHY interrupt, if necessary/possible */
- if (ugeth->ug_info->board_flags & FSL_UGETH_BRD_HAS_PHY_INTR) {
- if (request_irq(ugeth->ug_info->phy_interrupt,
- phy_interrupt, IRQF_SHARED,
- "phy_interrupt", mii_info->dev) < 0) {
- ugeth_err("%s: Can't get IRQ %d (PHY)",
- mii_info->dev->name,
- ugeth->ug_info->phy_interrupt);
- } else {
- mii_configure_phy_interrupt(ugeth->mii_info,
- MII_INTERRUPT_ENABLED);
- return;
- }
- }
-
- /* Start the timer again, this time in order to
- * handle a change in status */
- init_timer(&ugeth->phy_info_timer);
- ugeth->phy_info_timer.function = &ugeth_phy_timer;
- ugeth->phy_info_timer.data = (unsigned long)mii_info->dev;
- mod_timer(&ugeth->phy_info_timer, jiffies + PHY_CHANGE_TIME * HZ);
-}
-
/* Called when something needs to use the ethernet device */
/* Returns 0 for success. */
static int ucc_geth_open(struct net_device *dev)
return -EINVAL;
}
+ err = ucc_struct_init(ugeth);
+ if (err) {
+ ugeth_err("%s: Cannot configure internal struct, aborting.", dev->name);
+ return err;
+ }
+
err = ucc_geth_startup(ugeth);
if (err) {
ugeth_err("%s: Cannot configure net device, aborting.",
err = init_phy(dev);
if (err) {
- ugeth_err("%s: Cannot initialzie PHY, aborting.", dev->name);
+ ugeth_err("%s: Cannot initialize PHY, aborting.", dev->name);
return err;
}
+
+ phy_start(ugeth->phydev);
+
#ifndef CONFIG_UGETH_NAPI
err =
request_irq(ugeth->ug_info->uf_info.irq, ucc_geth_irq_handler, 0,
}
#endif /* CONFIG_UGETH_NAPI */
- /* Set up the PHY change work queue */
- INIT_WORK(&ugeth->tq, ugeth_phy_change);
-
- init_timer(&ugeth->phy_info_timer);
- ugeth->phy_info_timer.function = &ugeth_phy_startup_timer;
- ugeth->phy_info_timer.data = (unsigned long)ugeth->mii_info;
- mod_timer(&ugeth->phy_info_timer, jiffies + HZ);
-
err = ugeth_enable(ugeth, COMM_DIR_RX_AND_TX);
if (err) {
ugeth_err("%s: Cannot enable net device, aborting.", dev->name);
ucc_geth_stop(ugeth);
- /* Shutdown the PHY */
- if (ugeth->mii_info->phyinfo->close)
- ugeth->mii_info->phyinfo->close(ugeth->mii_info);
-
- kfree(ugeth->mii_info);
+ phy_disconnect(ugeth->phydev);
+ ugeth->phydev = NULL;
netif_stop_queue(dev);
const struct ethtool_ops ucc_geth_ethtool_ops = { };
+static phy_interface_t to_phy_interface(const char *interface_type)
+{
+ if (strcasecmp(interface_type, "mii") == 0)
+ return PHY_INTERFACE_MODE_MII;
+ if (strcasecmp(interface_type, "gmii") == 0)
+ return PHY_INTERFACE_MODE_GMII;
+ if (strcasecmp(interface_type, "tbi") == 0)
+ return PHY_INTERFACE_MODE_TBI;
+ if (strcasecmp(interface_type, "rmii") == 0)
+ return PHY_INTERFACE_MODE_RMII;
+ if (strcasecmp(interface_type, "rgmii") == 0)
+ return PHY_INTERFACE_MODE_RGMII;
+ if (strcasecmp(interface_type, "rgmii-id") == 0)
+ return PHY_INTERFACE_MODE_RGMII_ID;
+ if (strcasecmp(interface_type, "rtbi") == 0)
+ return PHY_INTERFACE_MODE_RTBI;
+
+ return PHY_INTERFACE_MODE_MII;
+}
+
static int ucc_geth_probe(struct of_device* ofdev, const struct of_device_id *match)
{
struct device *device = &ofdev->dev;
struct device_node *np = ofdev->node;
+ struct device_node *mdio;
struct net_device *dev = NULL;
struct ucc_geth_private *ugeth = NULL;
struct ucc_geth_info *ug_info;
struct resource res;
struct device_node *phy;
- int err, ucc_num, phy_interface;
- static int mii_mng_configured = 0;
+ int err, ucc_num, max_speed = 0;
const phandle *ph;
const unsigned int *prop;
const void *mac_addr;
+ phy_interface_t phy_interface;
+ static const int enet_to_speed[] = {
+ SPEED_10, SPEED_10, SPEED_10,
+ SPEED_100, SPEED_100, SPEED_100,
+ SPEED_1000, SPEED_1000, SPEED_1000, SPEED_1000,
+ };
+ static const phy_interface_t enet_to_phy_interface[] = {
+ PHY_INTERFACE_MODE_MII, PHY_INTERFACE_MODE_RMII,
+ PHY_INTERFACE_MODE_RGMII, PHY_INTERFACE_MODE_MII,
+ PHY_INTERFACE_MODE_RMII, PHY_INTERFACE_MODE_RGMII,
+ PHY_INTERFACE_MODE_GMII, PHY_INTERFACE_MODE_RGMII,
+ PHY_INTERFACE_MODE_TBI, PHY_INTERFACE_MODE_RTBI,
+ };
ugeth_vdbg("%s: IN", __FUNCTION__);
ug_info = &ugeth_info[ucc_num];
ug_info->uf_info.ucc_num = ucc_num;
+
prop = get_property(np, "rx-clock", NULL);
ug_info->uf_info.rx_clock = *prop;
prop = get_property(np, "tx-clock", NULL);
if (phy == NULL)
return -ENODEV;
+ /* set the PHY address */
prop = get_property(phy, "reg", NULL);
+ if (prop == NULL)
+ return -1;
ug_info->phy_address = *prop;
- prop = get_property(phy, "interface", NULL);
- ug_info->enet_interface = *prop;
- ug_info->phy_interrupt = irq_of_parse_and_map(phy, 0);
- ug_info->board_flags = (ug_info->phy_interrupt == NO_IRQ)?
- 0:FSL_UGETH_BRD_HAS_PHY_INTR;
+
+ /* get the phy interface type, or default to MII */
+ prop = get_property(np, "interface-type", NULL);
+ if (!prop) {
+ /* handle interface property present in old trees */
+ prop = get_property(phy, "interface", NULL);
+ if (prop != NULL)
+ phy_interface = enet_to_phy_interface[*prop];
+ else
+ phy_interface = PHY_INTERFACE_MODE_MII;
+ } else {
+ phy_interface = to_phy_interface((const char *)prop);
+ }
+
+ /* get speed, or derive from interface */
+ prop = get_property(np, "max-speed", NULL);
+ if (!prop) {
+ /* handle interface property present in old trees */
+ prop = get_property(phy, "interface", NULL);
+ if (prop != NULL)
+ max_speed = enet_to_speed[*prop];
+ } else {
+ max_speed = *prop;
+ }
+ if (!max_speed) {
+ switch (phy_interface) {
+ case PHY_INTERFACE_MODE_GMII:
+ case PHY_INTERFACE_MODE_RGMII:
+ case PHY_INTERFACE_MODE_RGMII_ID:
+ case PHY_INTERFACE_MODE_TBI:
+ case PHY_INTERFACE_MODE_RTBI:
+ max_speed = SPEED_1000;
+ break;
+ default:
+ max_speed = SPEED_100;
+ break;
+ }
+ }
+
+ if (max_speed == SPEED_1000) {
+ ug_info->uf_info.urfs = UCC_GETH_URFS_GIGA_INIT;
+ ug_info->uf_info.urfet = UCC_GETH_URFET_GIGA_INIT;
+ ug_info->uf_info.urfset = UCC_GETH_URFSET_GIGA_INIT;
+ ug_info->uf_info.utfs = UCC_GETH_UTFS_GIGA_INIT;
+ ug_info->uf_info.utfet = UCC_GETH_UTFET_GIGA_INIT;
+ ug_info->uf_info.utftt = UCC_GETH_UTFTT_GIGA_INIT;
+ }
+
+ /* Set the bus id */
+ mdio = of_get_parent(phy);
+
+ if (mdio == NULL)
+ return -1;
+
+ err = of_address_to_resource(mdio, 0, &res);
+ of_node_put(mdio);
+
+ if (err)
+ return -1;
+
+ ug_info->mdio_bus = res.start;
printk(KERN_INFO "ucc_geth: UCC%1d at 0x%8x (irq = %d) \n",
ug_info->uf_info.ucc_num + 1, ug_info->uf_info.regs,
return -ENODEV;
}
- /* FIXME: Work around for early chip rev. */
- /* There's a bug in initial chip rev(s) in the RGMII ac */
- /* timing. */
- /* The following compensates by writing to the reserved */
- /* QE Port Output Hold Registers (CPOH1?). */
- prop = get_property(phy, "interface", NULL);
- phy_interface = *prop;
- if ((phy_interface == ENET_1000_RGMII) ||
- (phy_interface == ENET_100_RGMII) ||
- (phy_interface == ENET_10_RGMII)) {
- struct device_node *soc;
- phys_addr_t immrbase = -1;
- u32 *tmp_reg;
- u32 tmp_val;
-
- soc = of_find_node_by_type(NULL, "soc");
- if (soc) {
- unsigned int size;
- const void *prop = get_property(soc, "reg", &size);
- immrbase = of_translate_address(soc, prop);
- of_node_put(soc);
- };
-
- tmp_reg = (u32 *) ioremap(immrbase + 0x14A8, 0x4);
- tmp_val = in_be32(tmp_reg);
- if (ucc_num == 1)
- out_be32(tmp_reg, tmp_val | 0x00003000);
- else if (ucc_num == 2)
- out_be32(tmp_reg, tmp_val | 0x0c000000);
- iounmap(tmp_reg);
- }
-
- if (!mii_mng_configured) {
- ucc_set_qe_mux_mii_mng(ucc_num);
- mii_mng_configured = 1;
- }
-
/* Create an ethernet device instance */
dev = alloc_etherdev(sizeof(*ugeth));
dev->set_multicast_list = ucc_geth_set_multi;
dev->ethtool_ops = &ucc_geth_ethtool_ops;
+ ugeth->msg_enable = (NETIF_MSG_IFUP << 1 ) - 1;
+ ugeth->phy_interface = phy_interface;
+ ugeth->max_speed = max_speed;
+
err = register_netdev(dev);
if (err) {
ugeth_err("%s: Cannot register net device, aborting.",
return err;
}
- ugeth->ug_info = ug_info;
- ugeth->dev = dev;
-
mac_addr = of_get_mac_address(np);
if (mac_addr)
memcpy(dev->dev_addr, mac_addr, 6);
+ ugeth->ug_info = ug_info;
+ ugeth->dev = dev;
+
return 0;
}
static int __init ucc_geth_init(void)
{
- int i;
+ int i, ret;
+
+ ret = uec_mdio_init();
+
+ if (ret)
+ return ret;
printk(KERN_INFO "ucc_geth: " DRV_DESC "\n");
for (i = 0; i < 8; i++)
memcpy(&(ugeth_info[i]), &ugeth_primary_info,
sizeof(ugeth_primary_info));
- return of_register_platform_driver(&ucc_geth_driver);
+ ret = of_register_platform_driver(&ucc_geth_driver);
+
+ if (ret)
+ uec_mdio_exit();
+
+ return ret;
}
static void __exit ucc_geth_exit(void)
{
of_unregister_platform_driver(&ucc_geth_driver);
+ uec_mdio_exit();
}
module_init(ucc_geth_init);
#include <asm/ucc.h>
#include <asm/ucc_fast.h>
+#include "ucc_geth_mii.h"
+
#define NUM_TX_QUEUES 8
#define NUM_RX_QUEUES 8
#define NUM_BDS_IN_PREFETCHED_BDS 4
#define ENET_INIT_PARAM_MAX_ENTRIES_RX 9
#define ENET_INIT_PARAM_MAX_ENTRIES_TX 8
-struct ucc_mii_mng {
- u32 miimcfg; /* MII management configuration reg */
- u32 miimcom; /* MII management command reg */
- u32 miimadd; /* MII management address reg */
- u32 miimcon; /* MII management control reg */
- u32 miimstat; /* MII management status reg */
- u32 miimind; /* MII management indication reg */
-} __attribute__ ((packed));
-
struct ucc_geth {
struct ucc_fast uccf;
u32 ipgifg; /* interframe gap reg. */
u32 hafdup; /* half-duplex reg. */
u8 res1[0x10];
- struct ucc_mii_mng miimng; /* MII management structure */
+ u8 miimng[0x18]; /* MII management structure moved to _mii.h */
u32 ifctl; /* interface control reg */
u32 ifstat; /* interface statux reg */
u32 macstnaddr1; /* mac station address part 1 reg */
#define UCCS_MPD 0x01 /* Magic Packet
Detected */
-/* UCC GETH MIIMCFG (MII Management Configuration Register) */
-#define MIIMCFG_RESET_MANAGEMENT 0x80000000 /* Reset
- management */
-#define MIIMCFG_NO_PREAMBLE 0x00000010 /* Preamble
- suppress */
-#define MIIMCFG_CLOCK_DIVIDE_SHIFT (31 - 31) /* clock divide
- << shift */
-#define MIIMCFG_CLOCK_DIVIDE_MAX 0xf /* clock divide max val
- */
-#define MIIMCFG_MANAGEMENT_CLOCK_DIVIDE_BY_2 0x00000000 /* divide by 2 */
-#define MIIMCFG_MANAGEMENT_CLOCK_DIVIDE_BY_4 0x00000001 /* divide by 4 */
-#define MIIMCFG_MANAGEMENT_CLOCK_DIVIDE_BY_6 0x00000002 /* divide by 6 */
-#define MIIMCFG_MANAGEMENT_CLOCK_DIVIDE_BY_8 0x00000003 /* divide by 8 */
-#define MIIMCFG_MANAGEMENT_CLOCK_DIVIDE_BY_10 0x00000004 /* divide by 10
- */
-#define MIIMCFG_MANAGEMENT_CLOCK_DIVIDE_BY_14 0x00000005 /* divide by 14
- */
-#define MIIMCFG_MANAGEMENT_CLOCK_DIVIDE_BY_16 0x00000008 /* divide by 16
- */
-#define MIIMCFG_MANAGEMENT_CLOCK_DIVIDE_BY_20 0x00000006 /* divide by 20
- */
-#define MIIMCFG_MANAGEMENT_CLOCK_DIVIDE_BY_28 0x00000007 /* divide by 28
- */
-#define MIIMCFG_MANAGEMENT_CLOCK_DIVIDE_BY_32 0x00000009 /* divide by 32
- */
-#define MIIMCFG_MANAGEMENT_CLOCK_DIVIDE_BY_48 0x0000000a /* divide by 48
- */
-#define MIIMCFG_MANAGEMENT_CLOCK_DIVIDE_BY_64 0x0000000b /* divide by 64
- */
-#define MIIMCFG_MANAGEMENT_CLOCK_DIVIDE_BY_80 0x0000000c /* divide by 80
- */
-#define MIIMCFG_MANAGEMENT_CLOCK_DIVIDE_BY_112 0x0000000d /* divide by
- 112 */
-#define MIIMCFG_MANAGEMENT_CLOCK_DIVIDE_BY_160 0x0000000e /* divide by
- 160 */
-#define MIIMCFG_MANAGEMENT_CLOCK_DIVIDE_BY_224 0x0000000f /* divide by
- 224 */
-
-/* UCC GETH MIIMCOM (MII Management Command Register) */
-#define MIIMCOM_SCAN_CYCLE 0x00000002 /* Scan cycle */
-#define MIIMCOM_READ_CYCLE 0x00000001 /* Read cycle */
-
-/* UCC GETH MIIMADD (MII Management Address Register) */
-#define MIIMADD_PHY_ADDRESS_SHIFT (31 - 23) /* PHY Address
- << shift */
-#define MIIMADD_PHY_REGISTER_SHIFT (31 - 31) /* PHY Register
- << shift */
-
-/* UCC GETH MIIMCON (MII Management Control Register) */
-#define MIIMCON_PHY_CONTROL_SHIFT (31 - 31) /* PHY Control
- << shift */
-#define MIIMCON_PHY_STATUS_SHIFT (31 - 31) /* PHY Status
- << shift */
-
-/* UCC GETH MIIMIND (MII Management Indicator Register) */
-#define MIIMIND_NOT_VALID 0x00000004 /* Not valid */
-#define MIIMIND_SCAN 0x00000002 /* Scan in
- progress */
-#define MIIMIND_BUSY 0x00000001
-
/* UCC GETH IFSTAT (Interface Status Register) */
#define IFSTAT_EXCESS_DEFER 0x00000200 /* Excessive
transmission
register */
#define UCC_GETH_MACCFG1_INIT 0
#define UCC_GETH_MACCFG2_INIT (MACCFG2_RESERVED_1)
-#define UCC_GETH_MIIMCFG_MNGMNT_CLC_DIV_INIT \
- (MIIMCFG_MANAGEMENT_CLOCK_DIVIDE_BY_112)
-
-/* Ethernet speed */
-enum enet_speed {
- ENET_SPEED_10BT, /* 10 Base T */
- ENET_SPEED_100BT, /* 100 Base T */
- ENET_SPEED_1000BT /* 1000 Base T */
-};
/* Ethernet Address Type. */
enum enet_addr_type {
ENET_ADDR_TYPE_BROADCAST
};
-/* TBI / MII Set Register */
-enum enet_tbi_mii_reg {
- ENET_TBI_MII_CR = 0x00, /* Control (CR ) */
- ENET_TBI_MII_SR = 0x01, /* Status (SR ) */
- ENET_TBI_MII_ANA = 0x04, /* AN advertisement (ANA ) */
- ENET_TBI_MII_ANLPBPA = 0x05, /* AN link partner base page ability
- (ANLPBPA) */
- ENET_TBI_MII_ANEX = 0x06, /* AN expansion (ANEX ) */
- ENET_TBI_MII_ANNPT = 0x07, /* AN next page transmit (ANNPT ) */
- ENET_TBI_MII_ANLPANP = 0x08, /* AN link partner ability next page
- (ANLPANP) */
- ENET_TBI_MII_EXST = 0x0F, /* Extended status (EXST ) */
- ENET_TBI_MII_JD = 0x10, /* Jitter diagnostics (JD ) */
- ENET_TBI_MII_TBICON = 0x11 /* TBI control (TBICON ) */
-};
-
/* UCC GETH 82xx Ethernet Address Recognition Location */
enum ucc_geth_enet_address_recognition_location {
UCC_GETH_ENET_ADDRESS_RECOGNITION_LOCATION_STATION_ADDRESS,/* station
u16 pausePeriod;
u16 extensionField;
u8 phy_address;
- u32 board_flags;
- u32 phy_interrupt;
+ u32 mdio_bus;
u8 weightfactor[NUM_TX_QUEUES];
u8 interruptcoalescingmaxvalue[NUM_RX_QUEUES];
u8 l2qt[UCC_GETH_VLAN_PRIORITY_MAX];
u8 iphoffset[TX_IP_OFFSET_ENTRY_MAX];
u16 bdRingLenTx[NUM_TX_QUEUES];
u16 bdRingLenRx[NUM_RX_QUEUES];
- enum enet_interface enet_interface;
enum ucc_geth_num_of_station_addresses numStationAddresses;
enum qe_fltr_largest_external_tbl_lookup_key_size
largestexternallookupkeysize;
/* index of the first skb which hasn't been transmitted yet. */
u16 skb_dirtytx[NUM_TX_QUEUES];
- struct work_struct tq;
- struct timer_list phy_info_timer;
struct ugeth_mii_info *mii_info;
+ struct phy_device *phydev;
+ phy_interface_t phy_interface;
+ int max_speed;
+ uint32_t msg_enable;
int oldspeed;
int oldduplex;
int oldlink;
--- /dev/null
+/*
+ * drivers/net/ucc_geth_mii.c
+ *
+ * Gianfar Ethernet Driver -- MIIM bus implementation
+ * Provides Bus interface for MIIM regs
+ *
+ * Author: Li Yang
+ *
+ * Copyright (c) 2002-2004 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/string.h>
+#include <linux/errno.h>
+#include <linux/unistd.h>
+#include <linux/slab.h>
+#include <linux/interrupt.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/skbuff.h>
+#include <linux/spinlock.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <asm/ocp.h>
+#include <linux/crc32.h>
+#include <linux/mii.h>
+#include <linux/phy.h>
+#include <linux/fsl_devices.h>
+
+#include <asm/of_platform.h>
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/uaccess.h>
+#include <asm/ucc.h>
+
+#include "ucc_geth_mii.h"
+#include "ucc_geth.h"
+
+#define DEBUG
+#ifdef DEBUG
+#define vdbg(format, arg...) printk(KERN_DEBUG , format "\n" , ## arg)
+#else
+#define vdbg(format, arg...) do {} while(0)
+#endif
+
+#define DRV_DESC "QE UCC Ethernet Controller MII Bus"
+#define DRV_NAME "fsl-uec_mdio"
+
+/* Write value to the PHY for this device to the register at regnum, */
+/* waiting until the write is done before it returns. All PHY */
+/* configuration has to be done through the master UEC MIIM regs */
+int uec_mdio_write(struct mii_bus *bus, int mii_id, int regnum, u16 value)
+{
+ struct ucc_mii_mng __iomem *regs = (void __iomem *)bus->priv;
+
+ /* Setting up the MII Mangement Address Register */
+ out_be32(®s->miimadd,
+ (mii_id << MIIMADD_PHY_ADDRESS_SHIFT) | regnum);
+
+ /* Setting up the MII Mangement Control Register with the value */
+ out_be32(®s->miimcon, value);
+
+ /* Wait till MII management write is complete */
+ while ((in_be32(®s->miimind)) & MIIMIND_BUSY)
+ cpu_relax();
+
+ return 0;
+}
+
+/* Reads from register regnum in the PHY for device dev, */
+/* returning the value. Clears miimcom first. All PHY */
+/* configuration has to be done through the TSEC1 MIIM regs */
+int uec_mdio_read(struct mii_bus *bus, int mii_id, int regnum)
+{
+ struct ucc_mii_mng __iomem *regs = (void __iomem *)bus->priv;
+ u16 value;
+
+ /* Setting up the MII Mangement Address Register */
+ out_be32(®s->miimadd,
+ (mii_id << MIIMADD_PHY_ADDRESS_SHIFT) | regnum);
+
+ /* Clear miimcom, perform an MII management read cycle */
+ out_be32(®s->miimcom, 0);
+ out_be32(®s->miimcom, MIIMCOM_READ_CYCLE);
+
+ /* Wait till MII management write is complete */
+ while ((in_be32(®s->miimind)) & (MIIMIND_BUSY | MIIMIND_NOT_VALID))
+ cpu_relax();
+
+ /* Read MII management status */
+ value = in_be32(®s->miimstat);
+
+ return value;
+}
+
+/* Reset the MIIM registers, and wait for the bus to free */
+int uec_mdio_reset(struct mii_bus *bus)
+{
+ struct ucc_mii_mng __iomem *regs = (void __iomem *)bus->priv;
+ unsigned int timeout = PHY_INIT_TIMEOUT;
+
+ spin_lock_bh(&bus->mdio_lock);
+
+ /* Reset the management interface */
+ out_be32(®s->miimcfg, MIIMCFG_RESET_MANAGEMENT);
+
+ /* Setup the MII Mgmt clock speed */
+ out_be32(®s->miimcfg, MIIMCFG_MANAGEMENT_CLOCK_DIVIDE_BY_112);
+
+ /* Wait until the bus is free */
+ while ((in_be32(®s->miimind) & MIIMIND_BUSY) && timeout--)
+ cpu_relax();
+
+ spin_unlock_bh(&bus->mdio_lock);
+
+ if (timeout <= 0) {
+ printk(KERN_ERR "%s: The MII Bus is stuck!\n", bus->name);
+ return -EBUSY;
+ }
+
+ return 0;
+}
+
+static int uec_mdio_probe(struct of_device *ofdev, const struct of_device_id *match)
+{
+ struct device *device = &ofdev->dev;
+ struct device_node *np = ofdev->node, *tempnp = NULL;
+ struct device_node *child = NULL;
+ struct ucc_mii_mng __iomem *regs;
+ struct mii_bus *new_bus;
+ struct resource res;
+ int k, err = 0;
+
+ new_bus = kzalloc(sizeof(struct mii_bus), GFP_KERNEL);
+
+ if (NULL == new_bus)
+ return -ENOMEM;
+
+ new_bus->name = "UCC Ethernet Controller MII Bus";
+ new_bus->read = &uec_mdio_read;
+ new_bus->write = &uec_mdio_write;
+ new_bus->reset = &uec_mdio_reset;
+
+ memset(&res, 0, sizeof(res));
+
+ err = of_address_to_resource(np, 0, &res);
+ if (err)
+ goto reg_map_fail;
+
+ new_bus->id = res.start;
+
+ new_bus->irq = kmalloc(32 * sizeof(int), GFP_KERNEL);
+
+ if (NULL == new_bus->irq) {
+ err = -ENOMEM;
+ goto reg_map_fail;
+ }
+
+ for (k = 0; k < 32; k++)
+ new_bus->irq[k] = PHY_POLL;
+
+ while ((child = of_get_next_child(np, child)) != NULL) {
+ int irq = irq_of_parse_and_map(child, 0);
+ if (irq != NO_IRQ) {
+ const u32 *id = get_property(child, "reg", NULL);
+ new_bus->irq[*id] = irq;
+ }
+ }
+
+ /* Set the base address */
+ regs = ioremap(res.start, sizeof(struct ucc_mii_mng));
+
+ if (NULL == regs) {
+ err = -ENOMEM;
+ goto ioremap_fail;
+ }
+
+ new_bus->priv = (void __force *)regs;
+
+ new_bus->dev = device;
+ dev_set_drvdata(device, new_bus);
+
+ /* Read MII management master from device tree */
+ while ((tempnp = of_find_compatible_node(tempnp, "network", "ucc_geth"))
+ != NULL) {
+ struct resource tempres;
+
+ err = of_address_to_resource(tempnp, 0, &tempres);
+ if (err)
+ goto bus_register_fail;
+
+ /* if our mdio regs fall within this UCC regs range */
+ if ((res.start >= tempres.start) &&
+ (res.end <= tempres.end)) {
+ /* set this UCC to be the MII master */
+ const u32 *id = get_property(tempnp, "device-id", NULL);
+ if (id == NULL)
+ goto bus_register_fail;
+
+ ucc_set_qe_mux_mii_mng(*id - 1);
+
+ /* assign the TBI an address which won't
+ * conflict with the PHYs */
+ out_be32(®s->utbipar, UTBIPAR_INIT_TBIPA);
+ break;
+ }
+ }
+
+ err = mdiobus_register(new_bus);
+ if (0 != err) {
+ printk(KERN_ERR "%s: Cannot register as MDIO bus\n",
+ new_bus->name);
+ goto bus_register_fail;
+ }
+
+ return 0;
+
+bus_register_fail:
+ iounmap(regs);
+ioremap_fail:
+ kfree(new_bus->irq);
+reg_map_fail:
+ kfree(new_bus);
+
+ return err;
+}
+
+int uec_mdio_remove(struct of_device *ofdev)
+{
+ struct device *device = &ofdev->dev;
+ struct mii_bus *bus = dev_get_drvdata(device);
+
+ mdiobus_unregister(bus);
+
+ dev_set_drvdata(device, NULL);
+
+ iounmap((void __iomem *)bus->priv);
+ bus->priv = NULL;
+ kfree(bus);
+
+ return 0;
+}
+
+static struct of_device_id uec_mdio_match[] = {
+ {
+ .type = "mdio",
+ .compatible = "ucc_geth_phy",
+ },
+ {},
+};
+
+MODULE_DEVICE_TABLE(of, uec_mdio_match);
+
+static struct of_platform_driver uec_mdio_driver = {
+ .name = DRV_NAME,
+ .probe = uec_mdio_probe,
+ .remove = uec_mdio_remove,
+ .match_table = uec_mdio_match,
+};
+
+int __init uec_mdio_init(void)
+{
+ return of_register_platform_driver(&uec_mdio_driver);
+}
+
+void __exit uec_mdio_exit(void)
+{
+ of_unregister_platform_driver(&uec_mdio_driver);
+}
--- /dev/null
+/*
+ * drivers/net/ucc_geth_mii.h
+ *
+ * Gianfar Ethernet Driver -- MII Management Bus Implementation
+ * Driver for the MDIO bus controller in the Gianfar register space
+ *
+ * Author: Andy Fleming
+ * Maintainer: Kumar Gala
+ *
+ * Copyright (c) 2002-2004 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ */
+#ifndef __UEC_MII_H
+#define __UEC_MII_H
+
+/* UCC GETH MIIMCFG (MII Management Configuration Register) */
+#define MIIMCFG_RESET_MANAGEMENT 0x80000000 /* Reset
+ management */
+#define MIIMCFG_NO_PREAMBLE 0x00000010 /* Preamble
+ suppress */
+#define MIIMCFG_CLOCK_DIVIDE_SHIFT (31 - 31) /* clock divide
+ << shift */
+#define MIIMCFG_CLOCK_DIVIDE_MAX 0xf /* max clock divide */
+#define MIIMCFG_MANAGEMENT_CLOCK_DIVIDE_BY_2 0x00000000
+#define MIIMCFG_MANAGEMENT_CLOCK_DIVIDE_BY_4 0x00000001
+#define MIIMCFG_MANAGEMENT_CLOCK_DIVIDE_BY_6 0x00000002
+#define MIIMCFG_MANAGEMENT_CLOCK_DIVIDE_BY_8 0x00000003
+#define MIIMCFG_MANAGEMENT_CLOCK_DIVIDE_BY_10 0x00000004
+#define MIIMCFG_MANAGEMENT_CLOCK_DIVIDE_BY_14 0x00000005
+#define MIIMCFG_MANAGEMENT_CLOCK_DIVIDE_BY_16 0x00000008
+#define MIIMCFG_MANAGEMENT_CLOCK_DIVIDE_BY_20 0x00000006
+#define MIIMCFG_MANAGEMENT_CLOCK_DIVIDE_BY_28 0x00000007
+#define MIIMCFG_MANAGEMENT_CLOCK_DIVIDE_BY_32 0x00000009
+#define MIIMCFG_MANAGEMENT_CLOCK_DIVIDE_BY_48 0x0000000a
+#define MIIMCFG_MANAGEMENT_CLOCK_DIVIDE_BY_64 0x0000000b
+#define MIIMCFG_MANAGEMENT_CLOCK_DIVIDE_BY_80 0x0000000c
+#define MIIMCFG_MANAGEMENT_CLOCK_DIVIDE_BY_112 0x0000000d
+#define MIIMCFG_MANAGEMENT_CLOCK_DIVIDE_BY_160 0x0000000e
+#define MIIMCFG_MANAGEMENT_CLOCK_DIVIDE_BY_224 0x0000000f
+
+/* UCC GETH MIIMCOM (MII Management Command Register) */
+#define MIIMCOM_SCAN_CYCLE 0x00000002 /* Scan cycle */
+#define MIIMCOM_READ_CYCLE 0x00000001 /* Read cycle */
+
+/* UCC GETH MIIMADD (MII Management Address Register) */
+#define MIIMADD_PHY_ADDRESS_SHIFT (31 - 23) /* PHY Address
+ << shift */
+#define MIIMADD_PHY_REGISTER_SHIFT (31 - 31) /* PHY Register
+ << shift */
+
+/* UCC GETH MIIMCON (MII Management Control Register) */
+#define MIIMCON_PHY_CONTROL_SHIFT (31 - 31) /* PHY Control
+ << shift */
+#define MIIMCON_PHY_STATUS_SHIFT (31 - 31) /* PHY Status
+ << shift */
+
+/* UCC GETH MIIMIND (MII Management Indicator Register) */
+#define MIIMIND_NOT_VALID 0x00000004 /* Not valid */
+#define MIIMIND_SCAN 0x00000002 /* Scan in
+ progress */
+#define MIIMIND_BUSY 0x00000001
+
+/* Initial TBI Physical Address */
+#define UTBIPAR_INIT_TBIPA 0x1f
+
+struct ucc_mii_mng {
+ u32 miimcfg; /* MII management configuration reg */
+ u32 miimcom; /* MII management command reg */
+ u32 miimadd; /* MII management address reg */
+ u32 miimcon; /* MII management control reg */
+ u32 miimstat; /* MII management status reg */
+ u32 miimind; /* MII management indication reg */
+ u8 notcare[28]; /* Space holder */
+ u32 utbipar; /* TBI phy address reg */
+} __attribute__ ((packed));
+
+/* TBI / MII Set Register */
+enum enet_tbi_mii_reg {
+ ENET_TBI_MII_CR = 0x00, /* Control */
+ ENET_TBI_MII_SR = 0x01, /* Status */
+ ENET_TBI_MII_ANA = 0x04, /* AN advertisement */
+ ENET_TBI_MII_ANLPBPA = 0x05, /* AN link partner base page ability */
+ ENET_TBI_MII_ANEX = 0x06, /* AN expansion */
+ ENET_TBI_MII_ANNPT = 0x07, /* AN next page transmit */
+ ENET_TBI_MII_ANLPANP = 0x08, /* AN link partner ability next page */
+ ENET_TBI_MII_EXST = 0x0F, /* Extended status */
+ ENET_TBI_MII_JD = 0x10, /* Jitter diagnostics */
+ ENET_TBI_MII_TBICON = 0x11 /* TBI control */
+};
+
+int uec_mdio_read(struct mii_bus *bus, int mii_id, int regnum);
+int uec_mdio_write(struct mii_bus *bus, int mii_id, int regnum, u16 value);
+int __init uec_mdio_init(void);
+void __exit uec_mdio_exit(void);
+#endif /* __UEC_MII_H */
+++ /dev/null
-/*
- * Copyright (C) Freescale Semicondutor, Inc. 2006. All rights reserved.
- *
- * Author: Shlomi Gridish <gridish@freescale.com>
- *
- * Description:
- * UCC GETH Driver -- PHY handling
- *
- * Changelog:
- * Jun 28, 2006 Li Yang <LeoLi@freescale.com>
- * - Rearrange code and style fixes
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- */
-
-#include <linux/kernel.h>
-#include <linux/string.h>
-#include <linux/errno.h>
-#include <linux/slab.h>
-#include <linux/interrupt.h>
-#include <linux/init.h>
-#include <linux/delay.h>
-#include <linux/netdevice.h>
-#include <linux/etherdevice.h>
-#include <linux/skbuff.h>
-#include <linux/spinlock.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/version.h>
-#include <linux/crc32.h>
-#include <linux/mii.h>
-#include <linux/ethtool.h>
-
-#include <asm/io.h>
-#include <asm/irq.h>
-#include <asm/uaccess.h>
-
-#include "ucc_geth.h"
-#include "ucc_geth_phy.h"
-
-#define ugphy_printk(level, format, arg...) \
- printk(level format "\n", ## arg)
-
-#define ugphy_dbg(format, arg...) \
- ugphy_printk(KERN_DEBUG, format , ## arg)
-#define ugphy_err(format, arg...) \
- ugphy_printk(KERN_ERR, format , ## arg)
-#define ugphy_info(format, arg...) \
- ugphy_printk(KERN_INFO, format , ## arg)
-#define ugphy_warn(format, arg...) \
- ugphy_printk(KERN_WARNING, format , ## arg)
-
-#ifdef UGETH_VERBOSE_DEBUG
-#define ugphy_vdbg ugphy_dbg
-#else
-#define ugphy_vdbg(fmt, args...) do { } while (0)
-#endif /* UGETH_VERBOSE_DEBUG */
-
-static void config_genmii_advert(struct ugeth_mii_info *mii_info);
-static void genmii_setup_forced(struct ugeth_mii_info *mii_info);
-static void genmii_restart_aneg(struct ugeth_mii_info *mii_info);
-static int gbit_config_aneg(struct ugeth_mii_info *mii_info);
-static int genmii_config_aneg(struct ugeth_mii_info *mii_info);
-static int genmii_update_link(struct ugeth_mii_info *mii_info);
-static int genmii_read_status(struct ugeth_mii_info *mii_info);
-
-static u16 ucc_geth_phy_read(struct ugeth_mii_info *mii_info, u16 regnum)
-{
- u16 retval;
- unsigned long flags;
-
- ugphy_vdbg("%s: IN", __FUNCTION__);
-
- spin_lock_irqsave(&mii_info->mdio_lock, flags);
- retval = mii_info->mdio_read(mii_info->dev, mii_info->mii_id, regnum);
- spin_unlock_irqrestore(&mii_info->mdio_lock, flags);
-
- return retval;
-}
-
-static void ucc_geth_phy_write(struct ugeth_mii_info *mii_info, u16 regnum, u16 val)
-{
- unsigned long flags;
-
- ugphy_vdbg("%s: IN", __FUNCTION__);
-
- spin_lock_irqsave(&mii_info->mdio_lock, flags);
- mii_info->mdio_write(mii_info->dev, mii_info->mii_id, regnum, val);
- spin_unlock_irqrestore(&mii_info->mdio_lock, flags);
-}
-
-/* Write value to the PHY for this device to the register at regnum, */
-/* waiting until the write is done before it returns. All PHY */
-/* configuration has to be done through the TSEC1 MIIM regs */
-void write_phy_reg(struct net_device *dev, int mii_id, int regnum, int value)
-{
- struct ucc_geth_private *ugeth = netdev_priv(dev);
- struct ucc_mii_mng *mii_regs;
- enum enet_tbi_mii_reg mii_reg = (enum enet_tbi_mii_reg) regnum;
- u32 tmp_reg;
-
- ugphy_vdbg("%s: IN", __FUNCTION__);
-
- spin_lock_irq(&ugeth->lock);
-
- mii_regs = ugeth->mii_info->mii_regs;
-
- /* Set this UCC to be the master of the MII managment */
- ucc_set_qe_mux_mii_mng(ugeth->ug_info->uf_info.ucc_num);
-
- /* Stop the MII management read cycle */
- out_be32(&mii_regs->miimcom, 0);
- /* Setting up the MII Mangement Address Register */
- tmp_reg = ((u32) mii_id << MIIMADD_PHY_ADDRESS_SHIFT) | mii_reg;
- out_be32(&mii_regs->miimadd, tmp_reg);
-
- /* Setting up the MII Mangement Control Register with the value */
- out_be32(&mii_regs->miimcon, (u32) value);
-
- /* Wait till MII management write is complete */
- while ((in_be32(&mii_regs->miimind)) & MIIMIND_BUSY)
- cpu_relax();
-
- spin_unlock_irq(&ugeth->lock);
-
- udelay(10000);
-}
-
-/* Reads from register regnum in the PHY for device dev, */
-/* returning the value. Clears miimcom first. All PHY */
-/* configuration has to be done through the TSEC1 MIIM regs */
-int read_phy_reg(struct net_device *dev, int mii_id, int regnum)
-{
- struct ucc_geth_private *ugeth = netdev_priv(dev);
- struct ucc_mii_mng *mii_regs;
- enum enet_tbi_mii_reg mii_reg = (enum enet_tbi_mii_reg) regnum;
- u32 tmp_reg;
- u16 value;
-
- ugphy_vdbg("%s: IN", __FUNCTION__);
-
- spin_lock_irq(&ugeth->lock);
-
- mii_regs = ugeth->mii_info->mii_regs;
-
- /* Setting up the MII Mangement Address Register */
- tmp_reg = ((u32) mii_id << MIIMADD_PHY_ADDRESS_SHIFT) | mii_reg;
- out_be32(&mii_regs->miimadd, tmp_reg);
-
- /* Perform an MII management read cycle */
- out_be32(&mii_regs->miimcom, MIIMCOM_READ_CYCLE);
-
- /* Wait till MII management write is complete */
- while ((in_be32(&mii_regs->miimind)) & MIIMIND_BUSY)
- cpu_relax();
-
- udelay(10000);
-
- /* Read MII management status */
- value = (u16) in_be32(&mii_regs->miimstat);
- out_be32(&mii_regs->miimcom, 0);
- if (value == 0xffff)
- ugphy_warn("read wrong value : mii_id %d,mii_reg %d, base %08x",
- mii_id, mii_reg, (u32) & (mii_regs->miimcfg));
-
- spin_unlock_irq(&ugeth->lock);
-
- return (value);
-}
-
-void mii_clear_phy_interrupt(struct ugeth_mii_info *mii_info)
-{
- ugphy_vdbg("%s: IN", __FUNCTION__);
-
- if (mii_info->phyinfo->ack_interrupt)
- mii_info->phyinfo->ack_interrupt(mii_info);
-}
-
-void mii_configure_phy_interrupt(struct ugeth_mii_info *mii_info,
- u32 interrupts)
-{
- ugphy_vdbg("%s: IN", __FUNCTION__);
-
- mii_info->interrupts = interrupts;
- if (mii_info->phyinfo->config_intr)
- mii_info->phyinfo->config_intr(mii_info);
-}
-
-/* Writes MII_ADVERTISE with the appropriate values, after
- * sanitizing advertise to make sure only supported features
- * are advertised
- */
-static void config_genmii_advert(struct ugeth_mii_info *mii_info)
-{
- u32 advertise;
- u16 adv;
-
- ugphy_vdbg("%s: IN", __FUNCTION__);
-
- /* Only allow advertising what this PHY supports */
- mii_info->advertising &= mii_info->phyinfo->features;
- advertise = mii_info->advertising;
-
- /* Setup standard advertisement */
- adv = ucc_geth_phy_read(mii_info, MII_ADVERTISE);
- adv &= ~(ADVERTISE_ALL | ADVERTISE_100BASE4);
- if (advertise & ADVERTISED_10baseT_Half)
- adv |= ADVERTISE_10HALF;
- if (advertise & ADVERTISED_10baseT_Full)
- adv |= ADVERTISE_10FULL;
- if (advertise & ADVERTISED_100baseT_Half)
- adv |= ADVERTISE_100HALF;
- if (advertise & ADVERTISED_100baseT_Full)
- adv |= ADVERTISE_100FULL;
- ucc_geth_phy_write(mii_info, MII_ADVERTISE, adv);
-}
-
-static void genmii_setup_forced(struct ugeth_mii_info *mii_info)
-{
- u16 ctrl;
- u32 features = mii_info->phyinfo->features;
-
- ugphy_vdbg("%s: IN", __FUNCTION__);
-
- ctrl = ucc_geth_phy_read(mii_info, MII_BMCR);
-
- ctrl &=
- ~(BMCR_FULLDPLX | BMCR_SPEED100 | BMCR_SPEED1000 | BMCR_ANENABLE);
- ctrl |= BMCR_RESET;
-
- switch (mii_info->speed) {
- case SPEED_1000:
- if (features & (SUPPORTED_1000baseT_Half
- | SUPPORTED_1000baseT_Full)) {
- ctrl |= BMCR_SPEED1000;
- break;
- }
- mii_info->speed = SPEED_100;
- case SPEED_100:
- if (features & (SUPPORTED_100baseT_Half
- | SUPPORTED_100baseT_Full)) {
- ctrl |= BMCR_SPEED100;
- break;
- }
- mii_info->speed = SPEED_10;
- case SPEED_10:
- if (features & (SUPPORTED_10baseT_Half
- | SUPPORTED_10baseT_Full))
- break;
- default: /* Unsupported speed! */
- ugphy_err("%s: Bad speed!", mii_info->dev->name);
- break;
- }
-
- ucc_geth_phy_write(mii_info, MII_BMCR, ctrl);
-}
-
-/* Enable and Restart Autonegotiation */
-static void genmii_restart_aneg(struct ugeth_mii_info *mii_info)
-{
- u16 ctl;
-
- ugphy_vdbg("%s: IN", __FUNCTION__);
-
- ctl = ucc_geth_phy_read(mii_info, MII_BMCR);
- ctl |= (BMCR_ANENABLE | BMCR_ANRESTART);
- ucc_geth_phy_write(mii_info, MII_BMCR, ctl);
-}
-
-static int gbit_config_aneg(struct ugeth_mii_info *mii_info)
-{
- u16 adv;
- u32 advertise;
-
- ugphy_vdbg("%s: IN", __FUNCTION__);
-
- if (mii_info->autoneg) {
- /* Configure the ADVERTISE register */
- config_genmii_advert(mii_info);
- advertise = mii_info->advertising;
-
- adv = ucc_geth_phy_read(mii_info, MII_1000BASETCONTROL);
- adv &= ~(MII_1000BASETCONTROL_FULLDUPLEXCAP |
- MII_1000BASETCONTROL_HALFDUPLEXCAP);
- if (advertise & SUPPORTED_1000baseT_Half)
- adv |= MII_1000BASETCONTROL_HALFDUPLEXCAP;
- if (advertise & SUPPORTED_1000baseT_Full)
- adv |= MII_1000BASETCONTROL_FULLDUPLEXCAP;
- ucc_geth_phy_write(mii_info, MII_1000BASETCONTROL, adv);
-
- /* Start/Restart aneg */
- genmii_restart_aneg(mii_info);
- } else
- genmii_setup_forced(mii_info);
-
- return 0;
-}
-
-static int genmii_config_aneg(struct ugeth_mii_info *mii_info)
-{
- ugphy_vdbg("%s: IN", __FUNCTION__);
-
- if (mii_info->autoneg) {
- config_genmii_advert(mii_info);
- genmii_restart_aneg(mii_info);
- } else
- genmii_setup_forced(mii_info);
-
- return 0;
-}
-
-static int genmii_update_link(struct ugeth_mii_info *mii_info)
-{
- u16 status;
-
- ugphy_vdbg("%s: IN", __FUNCTION__);
-
- /* Do a fake read */
- ucc_geth_phy_read(mii_info, MII_BMSR);
-
- /* Read link and autonegotiation status */
- status = ucc_geth_phy_read(mii_info, MII_BMSR);
- if ((status & BMSR_LSTATUS) == 0)
- mii_info->link = 0;
- else
- mii_info->link = 1;
-
- /* If we are autonegotiating, and not done,
- * return an error */
- if (mii_info->autoneg && !(status & BMSR_ANEGCOMPLETE))
- return -EAGAIN;
-
- return 0;
-}
-
-static int genmii_read_status(struct ugeth_mii_info *mii_info)
-{
- u16 status;
- int err;
-
- ugphy_vdbg("%s: IN", __FUNCTION__);
-
- /* Update the link, but return if there
- * was an error */
- err = genmii_update_link(mii_info);
- if (err)
- return err;
-
- if (mii_info->autoneg) {
- status = ucc_geth_phy_read(mii_info, MII_LPA);
-
- if (status & (LPA_10FULL | LPA_100FULL))
- mii_info->duplex = DUPLEX_FULL;
- else
- mii_info->duplex = DUPLEX_HALF;
- if (status & (LPA_100FULL | LPA_100HALF))
- mii_info->speed = SPEED_100;
- else
- mii_info->speed = SPEED_10;
- mii_info->pause = 0;
- }
- /* On non-aneg, we assume what we put in BMCR is the speed,
- * though magic-aneg shouldn't prevent this case from occurring
- */
-
- return 0;
-}
-
-static int marvell_init(struct ugeth_mii_info *mii_info)
-{
- ugphy_vdbg("%s: IN", __FUNCTION__);
-
- ucc_geth_phy_write(mii_info, 0x14, 0x0cd2);
- ucc_geth_phy_write(mii_info, 0x1b,
- (ucc_geth_phy_read(mii_info, 0x1b) & ~0x000f) | 0x000b);
- ucc_geth_phy_write(mii_info, MII_BMCR,
- ucc_geth_phy_read(mii_info, MII_BMCR) | BMCR_RESET);
- msleep(4000);
-
- return 0;
-}
-
-static int marvell_config_aneg(struct ugeth_mii_info *mii_info)
-{
- ugphy_vdbg("%s: IN", __FUNCTION__);
-
- /* The Marvell PHY has an errata which requires
- * that certain registers get written in order
- * to restart autonegotiation */
- ucc_geth_phy_write(mii_info, MII_BMCR, BMCR_RESET);
-
- ucc_geth_phy_write(mii_info, 0x1d, 0x1f);
- ucc_geth_phy_write(mii_info, 0x1e, 0x200c);
- ucc_geth_phy_write(mii_info, 0x1d, 0x5);
- ucc_geth_phy_write(mii_info, 0x1e, 0);
- ucc_geth_phy_write(mii_info, 0x1e, 0x100);
-
- gbit_config_aneg(mii_info);
-
- return 0;
-}
-
-static int marvell_read_status(struct ugeth_mii_info *mii_info)
-{
- u16 status;
- int err;
-
- ugphy_vdbg("%s: IN", __FUNCTION__);
-
- /* Update the link, but return if there
- * was an error */
- err = genmii_update_link(mii_info);
- if (err)
- return err;
-
- /* If the link is up, read the speed and duplex */
- /* If we aren't autonegotiating, assume speeds
- * are as set */
- if (mii_info->autoneg && mii_info->link) {
- int speed;
- status = ucc_geth_phy_read(mii_info, MII_M1011_PHY_SPEC_STATUS);
-
- /* Get the duplexity */
- if (status & MII_M1011_PHY_SPEC_STATUS_FULLDUPLEX)
- mii_info->duplex = DUPLEX_FULL;
- else
- mii_info->duplex = DUPLEX_HALF;
-
- /* Get the speed */
- speed = status & MII_M1011_PHY_SPEC_STATUS_SPD_MASK;
- switch (speed) {
- case MII_M1011_PHY_SPEC_STATUS_1000:
- mii_info->speed = SPEED_1000;
- break;
- case MII_M1011_PHY_SPEC_STATUS_100:
- mii_info->speed = SPEED_100;
- break;
- default:
- mii_info->speed = SPEED_10;
- break;
- }
- mii_info->pause = 0;
- }
-
- return 0;
-}
-
-static int marvell_ack_interrupt(struct ugeth_mii_info *mii_info)
-{
- ugphy_vdbg("%s: IN", __FUNCTION__);
-
- /* Clear the interrupts by reading the reg */
- ucc_geth_phy_read(mii_info, MII_M1011_IEVENT);
-
- return 0;
-}
-
-static int marvell_config_intr(struct ugeth_mii_info *mii_info)
-{
- ugphy_vdbg("%s: IN", __FUNCTION__);
-
- if (mii_info->interrupts == MII_INTERRUPT_ENABLED)
- ucc_geth_phy_write(mii_info, MII_M1011_IMASK, MII_M1011_IMASK_INIT);
- else
- ucc_geth_phy_write(mii_info, MII_M1011_IMASK, MII_M1011_IMASK_CLEAR);
-
- return 0;
-}
-
-static int cis820x_init(struct ugeth_mii_info *mii_info)
-{
- ugphy_vdbg("%s: IN", __FUNCTION__);
-
- ucc_geth_phy_write(mii_info, MII_CIS8201_AUX_CONSTAT,
- MII_CIS8201_AUXCONSTAT_INIT);
- ucc_geth_phy_write(mii_info, MII_CIS8201_EXT_CON1, MII_CIS8201_EXTCON1_INIT);
-
- return 0;
-}
-
-static int cis820x_read_status(struct ugeth_mii_info *mii_info)
-{
- u16 status;
- int err;
-
- ugphy_vdbg("%s: IN", __FUNCTION__);
-
- /* Update the link, but return if there
- * was an error */
- err = genmii_update_link(mii_info);
- if (err)
- return err;
-
- /* If the link is up, read the speed and duplex */
- /* If we aren't autonegotiating, assume speeds
- * are as set */
- if (mii_info->autoneg && mii_info->link) {
- int speed;
-
- status = ucc_geth_phy_read(mii_info, MII_CIS8201_AUX_CONSTAT);
- if (status & MII_CIS8201_AUXCONSTAT_DUPLEX)
- mii_info->duplex = DUPLEX_FULL;
- else
- mii_info->duplex = DUPLEX_HALF;
-
- speed = status & MII_CIS8201_AUXCONSTAT_SPEED;
-
- switch (speed) {
- case MII_CIS8201_AUXCONSTAT_GBIT:
- mii_info->speed = SPEED_1000;
- break;
- case MII_CIS8201_AUXCONSTAT_100:
- mii_info->speed = SPEED_100;
- break;
- default:
- mii_info->speed = SPEED_10;
- break;
- }
- }
-
- return 0;
-}
-
-static int cis820x_ack_interrupt(struct ugeth_mii_info *mii_info)
-{
- ugphy_vdbg("%s: IN", __FUNCTION__);
-
- ucc_geth_phy_read(mii_info, MII_CIS8201_ISTAT);
-
- return 0;
-}
-
-static int cis820x_config_intr(struct ugeth_mii_info *mii_info)
-{
- ugphy_vdbg("%s: IN", __FUNCTION__);
-
- if (mii_info->interrupts == MII_INTERRUPT_ENABLED)
- ucc_geth_phy_write(mii_info, MII_CIS8201_IMASK, MII_CIS8201_IMASK_MASK);
- else
- ucc_geth_phy_write(mii_info, MII_CIS8201_IMASK, 0);
-
- return 0;
-}
-
-#define DM9161_DELAY 10
-
-static int dm9161_read_status(struct ugeth_mii_info *mii_info)
-{
- u16 status;
- int err;
-
- ugphy_vdbg("%s: IN", __FUNCTION__);
-
- /* Update the link, but return if there
- * was an error */
- err = genmii_update_link(mii_info);
- if (err)
- return err;
-
- /* If the link is up, read the speed and duplex */
- /* If we aren't autonegotiating, assume speeds
- * are as set */
- if (mii_info->autoneg && mii_info->link) {
- status = ucc_geth_phy_read(mii_info, MII_DM9161_SCSR);
- if (status & (MII_DM9161_SCSR_100F | MII_DM9161_SCSR_100H))
- mii_info->speed = SPEED_100;
- else
- mii_info->speed = SPEED_10;
-
- if (status & (MII_DM9161_SCSR_100F | MII_DM9161_SCSR_10F))
- mii_info->duplex = DUPLEX_FULL;
- else
- mii_info->duplex = DUPLEX_HALF;
- }
-
- return 0;
-}
-
-static int dm9161_config_aneg(struct ugeth_mii_info *mii_info)
-{
- struct dm9161_private *priv = mii_info->priv;
-
- ugphy_vdbg("%s: IN", __FUNCTION__);
-
- if (0 == priv->resetdone)
- return -EAGAIN;
-
- return 0;
-}
-
-static void dm9161_timer(unsigned long data)
-{
- struct ugeth_mii_info *mii_info = (struct ugeth_mii_info *)data;
- struct dm9161_private *priv = mii_info->priv;
- u16 status = ucc_geth_phy_read(mii_info, MII_BMSR);
-
- ugphy_vdbg("%s: IN", __FUNCTION__);
-
- if (status & BMSR_ANEGCOMPLETE) {
- priv->resetdone = 1;
- } else
- mod_timer(&priv->timer, jiffies + DM9161_DELAY * HZ);
-}
-
-static int dm9161_init(struct ugeth_mii_info *mii_info)
-{
- struct dm9161_private *priv;
-
- ugphy_vdbg("%s: IN", __FUNCTION__);
-
- /* Allocate the private data structure */
- priv = kmalloc(sizeof(struct dm9161_private), GFP_KERNEL);
-
- if (NULL == priv)
- return -ENOMEM;
-
- mii_info->priv = priv;
-
- /* Reset is not done yet */
- priv->resetdone = 0;
-
- ucc_geth_phy_write(mii_info, MII_BMCR,
- ucc_geth_phy_read(mii_info, MII_BMCR) | BMCR_RESET);
-
- ucc_geth_phy_write(mii_info, MII_BMCR,
- ucc_geth_phy_read(mii_info, MII_BMCR) & ~BMCR_ISOLATE);
-
- config_genmii_advert(mii_info);
- /* Start/Restart aneg */
- genmii_config_aneg(mii_info);
-
- /* Start a timer for DM9161_DELAY seconds to wait
- * for the PHY to be ready */
- init_timer(&priv->timer);
- priv->timer.function = &dm9161_timer;
- priv->timer.data = (unsigned long)mii_info;
- mod_timer(&priv->timer, jiffies + DM9161_DELAY * HZ);
-
- return 0;
-}
-
-static void dm9161_close(struct ugeth_mii_info *mii_info)
-{
- struct dm9161_private *priv = mii_info->priv;
-
- ugphy_vdbg("%s: IN", __FUNCTION__);
-
- del_timer_sync(&priv->timer);
- kfree(priv);
-}
-
-static int dm9161_ack_interrupt(struct ugeth_mii_info *mii_info)
-{
- ugphy_vdbg("%s: IN", __FUNCTION__);
-
- /* Clear the interrupts by reading the reg */
- ucc_geth_phy_read(mii_info, MII_DM9161_INTR);
-
-
- return 0;
-}
-
-static int dm9161_config_intr(struct ugeth_mii_info *mii_info)
-{
- ugphy_vdbg("%s: IN", __FUNCTION__);
-
- if (mii_info->interrupts == MII_INTERRUPT_ENABLED)
- ucc_geth_phy_write(mii_info, MII_DM9161_INTR, MII_DM9161_INTR_INIT);
- else
- ucc_geth_phy_write(mii_info, MII_DM9161_INTR, MII_DM9161_INTR_STOP);
-
- return 0;
-}
-
-/* Cicada 820x */
-static struct phy_info phy_info_cis820x = {
- .phy_id = 0x000fc440,
- .name = "Cicada Cis8204",
- .phy_id_mask = 0x000fffc0,
- .features = MII_GBIT_FEATURES,
- .init = &cis820x_init,
- .config_aneg = &gbit_config_aneg,
- .read_status = &cis820x_read_status,
- .ack_interrupt = &cis820x_ack_interrupt,
- .config_intr = &cis820x_config_intr,
-};
-
-static struct phy_info phy_info_dm9161 = {
- .phy_id = 0x0181b880,
- .phy_id_mask = 0x0ffffff0,
- .name = "Davicom DM9161E",
- .init = dm9161_init,
- .config_aneg = dm9161_config_aneg,
- .read_status = dm9161_read_status,
- .close = dm9161_close,
-};
-
-static struct phy_info phy_info_dm9161a = {
- .phy_id = 0x0181b8a0,
- .phy_id_mask = 0x0ffffff0,
- .name = "Davicom DM9161A",
- .features = MII_BASIC_FEATURES,
- .init = dm9161_init,
- .config_aneg = dm9161_config_aneg,
- .read_status = dm9161_read_status,
- .ack_interrupt = dm9161_ack_interrupt,
- .config_intr = dm9161_config_intr,
- .close = dm9161_close,
-};
-
-static struct phy_info phy_info_marvell = {
- .phy_id = 0x01410c00,
- .phy_id_mask = 0xffffff00,
- .name = "Marvell 88E11x1",
- .features = MII_GBIT_FEATURES,
- .init = &marvell_init,
- .config_aneg = &marvell_config_aneg,
- .read_status = &marvell_read_status,
- .ack_interrupt = &marvell_ack_interrupt,
- .config_intr = &marvell_config_intr,
-};
-
-static struct phy_info phy_info_genmii = {
- .phy_id = 0x00000000,
- .phy_id_mask = 0x00000000,
- .name = "Generic MII",
- .features = MII_BASIC_FEATURES,
- .config_aneg = genmii_config_aneg,
- .read_status = genmii_read_status,
-};
-
-static struct phy_info *phy_info[] = {
- &phy_info_cis820x,
- &phy_info_marvell,
- &phy_info_dm9161,
- &phy_info_dm9161a,
- &phy_info_genmii,
- NULL
-};
-
-/* Use the PHY ID registers to determine what type of PHY is attached
- * to device dev. return a struct phy_info structure describing that PHY
- */
-struct phy_info *get_phy_info(struct ugeth_mii_info *mii_info)
-{
- u16 phy_reg;
- u32 phy_ID;
- int i;
- struct phy_info *theInfo = NULL;
- struct net_device *dev = mii_info->dev;
-
- ugphy_vdbg("%s: IN", __FUNCTION__);
-
- /* Grab the bits from PHYIR1, and put them in the upper half */
- phy_reg = ucc_geth_phy_read(mii_info, MII_PHYSID1);
- phy_ID = (phy_reg & 0xffff) << 16;
-
- /* Grab the bits from PHYIR2, and put them in the lower half */
- phy_reg = ucc_geth_phy_read(mii_info, MII_PHYSID2);
- phy_ID |= (phy_reg & 0xffff);
-
- /* loop through all the known PHY types, and find one that */
- /* matches the ID we read from the PHY. */
- for (i = 0; phy_info[i]; i++)
- if (phy_info[i]->phy_id == (phy_ID & phy_info[i]->phy_id_mask)){
- theInfo = phy_info[i];
- break;
- }
-
- /* This shouldn't happen, as we have generic PHY support */
- if (theInfo == NULL) {
- ugphy_info("%s: PHY id %x is not supported!", dev->name,
- phy_ID);
- return NULL;
- } else {
- ugphy_info("%s: PHY is %s (%x)", dev->name, theInfo->name,
- phy_ID);
- }
-
- return theInfo;
-}
+++ /dev/null
-/*
- * Copyright (C) Freescale Semicondutor, Inc. 2006. All rights reserved.
- *
- * Author: Shlomi Gridish <gridish@freescale.com>
- *
- * Description:
- * UCC GETH Driver -- PHY handling
- *
- * Changelog:
- * Jun 28, 2006 Li Yang <LeoLi@freescale.com>
- * - Rearrange code and style fixes
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- */
-#ifndef __UCC_GETH_PHY_H__
-#define __UCC_GETH_PHY_H__
-
-#define MII_end ((u32)-2)
-#define MII_read ((u32)-1)
-
-#define MIIMIND_BUSY 0x00000001
-#define MIIMIND_NOTVALID 0x00000004
-
-#define UGETH_AN_TIMEOUT 2000
-
-/* 1000BT control (Marvell & BCM54xx at least) */
-#define MII_1000BASETCONTROL 0x09
-#define MII_1000BASETCONTROL_FULLDUPLEXCAP 0x0200
-#define MII_1000BASETCONTROL_HALFDUPLEXCAP 0x0100
-
-/* Cicada Extended Control Register 1 */
-#define MII_CIS8201_EXT_CON1 0x17
-#define MII_CIS8201_EXTCON1_INIT 0x0000
-
-/* Cicada Interrupt Mask Register */
-#define MII_CIS8201_IMASK 0x19
-#define MII_CIS8201_IMASK_IEN 0x8000
-#define MII_CIS8201_IMASK_SPEED 0x4000
-#define MII_CIS8201_IMASK_LINK 0x2000
-#define MII_CIS8201_IMASK_DUPLEX 0x1000
-#define MII_CIS8201_IMASK_MASK 0xf000
-
-/* Cicada Interrupt Status Register */
-#define MII_CIS8201_ISTAT 0x1a
-#define MII_CIS8201_ISTAT_STATUS 0x8000
-#define MII_CIS8201_ISTAT_SPEED 0x4000
-#define MII_CIS8201_ISTAT_LINK 0x2000
-#define MII_CIS8201_ISTAT_DUPLEX 0x1000
-
-/* Cicada Auxiliary Control/Status Register */
-#define MII_CIS8201_AUX_CONSTAT 0x1c
-#define MII_CIS8201_AUXCONSTAT_INIT 0x0004
-#define MII_CIS8201_AUXCONSTAT_DUPLEX 0x0020
-#define MII_CIS8201_AUXCONSTAT_SPEED 0x0018
-#define MII_CIS8201_AUXCONSTAT_GBIT 0x0010
-#define MII_CIS8201_AUXCONSTAT_100 0x0008
-
-/* 88E1011 PHY Status Register */
-#define MII_M1011_PHY_SPEC_STATUS 0x11
-#define MII_M1011_PHY_SPEC_STATUS_1000 0x8000
-#define MII_M1011_PHY_SPEC_STATUS_100 0x4000
-#define MII_M1011_PHY_SPEC_STATUS_SPD_MASK 0xc000
-#define MII_M1011_PHY_SPEC_STATUS_FULLDUPLEX 0x2000
-#define MII_M1011_PHY_SPEC_STATUS_RESOLVED 0x0800
-#define MII_M1011_PHY_SPEC_STATUS_LINK 0x0400
-
-#define MII_M1011_IEVENT 0x13
-#define MII_M1011_IEVENT_CLEAR 0x0000
-
-#define MII_M1011_IMASK 0x12
-#define MII_M1011_IMASK_INIT 0x6400
-#define MII_M1011_IMASK_CLEAR 0x0000
-
-#define MII_DM9161_SCR 0x10
-#define MII_DM9161_SCR_INIT 0x0610
-
-/* DM9161 Specified Configuration and Status Register */
-#define MII_DM9161_SCSR 0x11
-#define MII_DM9161_SCSR_100F 0x8000
-#define MII_DM9161_SCSR_100H 0x4000
-#define MII_DM9161_SCSR_10F 0x2000
-#define MII_DM9161_SCSR_10H 0x1000
-
-/* DM9161 Interrupt Register */
-#define MII_DM9161_INTR 0x15
-#define MII_DM9161_INTR_PEND 0x8000
-#define MII_DM9161_INTR_DPLX_MASK 0x0800
-#define MII_DM9161_INTR_SPD_MASK 0x0400
-#define MII_DM9161_INTR_LINK_MASK 0x0200
-#define MII_DM9161_INTR_MASK 0x0100
-#define MII_DM9161_INTR_DPLX_CHANGE 0x0010
-#define MII_DM9161_INTR_SPD_CHANGE 0x0008
-#define MII_DM9161_INTR_LINK_CHANGE 0x0004
-#define MII_DM9161_INTR_INIT 0x0000
-#define MII_DM9161_INTR_STOP \
-(MII_DM9161_INTR_DPLX_MASK | MII_DM9161_INTR_SPD_MASK \
- | MII_DM9161_INTR_LINK_MASK | MII_DM9161_INTR_MASK)
-
-/* DM9161 10BT Configuration/Status */
-#define MII_DM9161_10BTCSR 0x12
-#define MII_DM9161_10BTCSR_INIT 0x7800
-
-#define MII_BASIC_FEATURES (SUPPORTED_10baseT_Half | \
- SUPPORTED_10baseT_Full | \
- SUPPORTED_100baseT_Half | \
- SUPPORTED_100baseT_Full | \
- SUPPORTED_Autoneg | \
- SUPPORTED_TP | \
- SUPPORTED_MII)
-
-#define MII_GBIT_FEATURES (MII_BASIC_FEATURES | \
- SUPPORTED_1000baseT_Half | \
- SUPPORTED_1000baseT_Full)
-
-#define MII_READ_COMMAND 0x00000001
-
-#define MII_INTERRUPT_DISABLED 0x0
-#define MII_INTERRUPT_ENABLED 0x1
-/* Taken from mii_if_info and sungem_phy.h */
-struct ugeth_mii_info {
- /* Information about the PHY type */
- /* And management functions */
- struct phy_info *phyinfo;
-
- struct ucc_mii_mng *mii_regs;
-
- /* forced speed & duplex (no autoneg)
- * partner speed & duplex & pause (autoneg)
- */
- int speed;
- int duplex;
- int pause;
-
- /* The most recently read link state */
- int link;
-
- /* Enabled Interrupts */
- u32 interrupts;
-
- u32 advertising;
- int autoneg;
- int mii_id;
-
- /* private data pointer */
- /* For use by PHYs to maintain extra state */
- void *priv;
-
- /* Provided by host chip */
- struct net_device *dev;
-
- /* A lock to ensure that only one thing can read/write
- * the MDIO bus at a time */
- spinlock_t mdio_lock;
-
- /* Provided by ethernet driver */
- int (*mdio_read) (struct net_device * dev, int mii_id, int reg);
- void (*mdio_write) (struct net_device * dev, int mii_id, int reg,
- int val);
-};
-
-/* struct phy_info: a structure which defines attributes for a PHY
- *
- * id will contain a number which represents the PHY. During
- * startup, the driver will poll the PHY to find out what its
- * UID--as defined by registers 2 and 3--is. The 32-bit result
- * gotten from the PHY will be ANDed with phy_id_mask to
- * discard any bits which may change based on revision numbers
- * unimportant to functionality
- *
- * There are 6 commands which take a ugeth_mii_info structure.
- * Each PHY must declare config_aneg, and read_status.
- */
-struct phy_info {
- u32 phy_id;
- char *name;
- unsigned int phy_id_mask;
- u32 features;
-
- /* Called to initialize the PHY */
- int (*init) (struct ugeth_mii_info * mii_info);
-
- /* Called to suspend the PHY for power */
- int (*suspend) (struct ugeth_mii_info * mii_info);
-
- /* Reconfigures autonegotiation (or disables it) */
- int (*config_aneg) (struct ugeth_mii_info * mii_info);
-
- /* Determines the negotiated speed and duplex */
- int (*read_status) (struct ugeth_mii_info * mii_info);
-
- /* Clears any pending interrupts */
- int (*ack_interrupt) (struct ugeth_mii_info * mii_info);
-
- /* Enables or disables interrupts */
- int (*config_intr) (struct ugeth_mii_info * mii_info);
-
- /* Clears up any memory if needed */
- void (*close) (struct ugeth_mii_info * mii_info);
-};
-
-struct phy_info *get_phy_info(struct ugeth_mii_info *mii_info);
-void write_phy_reg(struct net_device *dev, int mii_id, int regnum, int value);
-int read_phy_reg(struct net_device *dev, int mii_id, int regnum);
-void mii_clear_phy_interrupt(struct ugeth_mii_info *mii_info);
-void mii_configure_phy_interrupt(struct ugeth_mii_info *mii_info,
- u32 interrupts);
-
-struct dm9161_private {
- struct timer_list timer;
- int resetdone;
-};
-
-#endif /* __UCC_GETH_PHY_H__ */
u32 sysclk;
};
-/* Ethernet interface (phy management and speed)
-*/
-enum enet_interface {
- ENET_10_MII, /* 10 Base T, MII interface */
- ENET_10_RMII, /* 10 Base T, RMII interface */
- ENET_10_RGMII, /* 10 Base T, RGMII interface */
- ENET_100_MII, /* 100 Base T, MII interface */
- ENET_100_RMII, /* 100 Base T, RMII interface */
- ENET_100_RGMII, /* 100 Base T, RGMII interface */
- ENET_1000_GMII, /* 1000 Base T, GMII interface */
- ENET_1000_RGMII, /* 1000 Base T, RGMII interface */
- ENET_1000_TBI, /* 1000 Base T, TBI interface */
- ENET_1000_RTBI /* 1000 Base T, RTBI interface */
-};
-
-struct ucc_geth_platform_data {
- /* device specific information */
- u32 device_flags;
- u32 phy_reg_addr;
-
- /* board specific information */
- u32 board_flags;
- u8 rx_clock;
- u8 tx_clock;
- u32 phy_id;
- enum enet_interface phy_interface;
- u32 phy_interrupt;
- u8 mac_addr[6];
-};
-
-/* Flags related to UCC Gigabit Ethernet device features */
-#define FSL_UGETH_DEV_HAS_GIGABIT 0x00000001
-#define FSL_UGETH_DEV_HAS_COALESCE 0x00000002
-#define FSL_UGETH_DEV_HAS_RMON 0x00000004
-
-/* Flags in ucc_geth_platform_data */
-#define FSL_UGETH_BRD_HAS_PHY_INTR 0x00000001
- /* if not set use a timer */
-
#endif /* _FSL_DEVICE_H_ */
#endif /* __KERNEL__ */
projects / linux-2.6 / commitdiff