#define PCI_REG_WUM8 0x0E8
#define PCI_CFG_PMC_PME_FROM_D3COLD_SUPPORT (0x80000000)
-/*=== CSR (control and status registers) ===*/
-#define CSR_BASE (0x000)
-
-#define CSR_HW_IF_CONFIG_REG (CSR_BASE+0x000) /* hardware interface config */
-#define CSR_INT_COALESCING (CSR_BASE+0x004) /* accum ints, 32-usec units */
-#define CSR_INT (CSR_BASE+0x008) /* host interrupt status/ack */
-#define CSR_INT_MASK (CSR_BASE+0x00c) /* host interrupt enable */
-#define CSR_FH_INT_STATUS (CSR_BASE+0x010) /* busmaster int status/ack*/
-#define CSR_GPIO_IN (CSR_BASE+0x018) /* read external chip pins */
-#define CSR_RESET (CSR_BASE+0x020) /* busmaster enable, NMI, etc*/
-#define CSR_GP_CNTRL (CSR_BASE+0x024)
-
-/*
- * Hardware revision info
- * Bit fields:
- * 31-8: Reserved
- * 7-4: Type of device: 0x0 = 4965, 0xd = 3945
- * 3-2: Revision step: 0 = A, 1 = B, 2 = C, 3 = D
- * 1-0: "Dash" value, as in A-1, etc.
- */
-#define CSR_HW_REV (CSR_BASE+0x028)
-
-/* EEPROM reads */
-#define CSR_EEPROM_REG (CSR_BASE+0x02c)
-#define CSR_EEPROM_GP (CSR_BASE+0x030)
-#define CSR_GP_UCODE (CSR_BASE+0x044)
-#define CSR_UCODE_DRV_GP1 (CSR_BASE+0x054)
-#define CSR_UCODE_DRV_GP1_SET (CSR_BASE+0x058)
-#define CSR_UCODE_DRV_GP1_CLR (CSR_BASE+0x05c)
-#define CSR_UCODE_DRV_GP2 (CSR_BASE+0x060)
-#define CSR_GIO_CHICKEN_BITS (CSR_BASE+0x100)
-
-/* Analog phase-lock-loop configuration (3945 only)
- * Set bit 24. */
-#define CSR_ANA_PLL_CFG (CSR_BASE+0x20c)
-
-/* Bits for CSR_HW_IF_CONFIG_REG */
-#define CSR_HW_IF_CONFIG_REG_BIT_ALMAGOR_MB (0x00000100)
-#define CSR_HW_IF_CONFIG_REG_BIT_ALMAGOR_MM (0x00000200)
-#define CSR_HW_IF_CONFIG_REG_BIT_SKU_MRC (0x00000400)
-#define CSR_HW_IF_CONFIG_REG_BIT_BOARD_TYPE (0x00000800)
-#define CSR_HW_IF_CONFIG_REG_BITS_SILICON_TYPE_A (0x00000000)
-#define CSR_HW_IF_CONFIG_REG_BITS_SILICON_TYPE_B (0x00001000)
-#define CSR_HW_IF_CONFIG_REG_BIT_EEPROM_OWN_SEM (0x00200000)
-
-/* interrupt flags in INTA, set by uCode or hardware (e.g. dma),
- * acknowledged (reset) by host writing "1" to flagged bits. */
-#define CSR_INT_BIT_FH_RX (1 << 31) /* Rx DMA, cmd responses, FH_INT[17:16] */
-#define CSR_INT_BIT_HW_ERR (1 << 29) /* DMA hardware error FH_INT[31] */
-#define CSR_INT_BIT_DNLD (1 << 28) /* uCode Download */
-#define CSR_INT_BIT_FH_TX (1 << 27) /* Tx DMA FH_INT[1:0] */
-#define CSR_INT_BIT_SCD (1 << 26) /* TXQ pointer advanced */
-#define CSR_INT_BIT_SW_ERR (1 << 25) /* uCode error */
-#define CSR_INT_BIT_RF_KILL (1 << 7) /* HW RFKILL switch GP_CNTRL[27] toggled */
-#define CSR_INT_BIT_CT_KILL (1 << 6) /* Critical temp (chip too hot) rfkill */
-#define CSR_INT_BIT_SW_RX (1 << 3) /* Rx, command responses, 3945 */
-#define CSR_INT_BIT_WAKEUP (1 << 1) /* NIC controller waking up (pwr mgmt) */
-#define CSR_INT_BIT_ALIVE (1 << 0) /* uCode interrupts once it initializes */
-
-#define CSR_INI_SET_MASK (CSR_INT_BIT_FH_RX | \
- CSR_INT_BIT_HW_ERR | \
- CSR_INT_BIT_FH_TX | \
- CSR_INT_BIT_SW_ERR | \
- CSR_INT_BIT_RF_KILL | \
- CSR_INT_BIT_SW_RX | \
- CSR_INT_BIT_WAKEUP | \
- CSR_INT_BIT_ALIVE)
-
-/* interrupt flags in FH (flow handler) (PCI busmaster DMA) */
-#define CSR_FH_INT_BIT_ERR (1 << 31) /* Error */
-#define CSR_FH_INT_BIT_HI_PRIOR (1 << 30) /* High priority Rx, bypass coalescing */
-#define CSR_FH_INT_BIT_RX_CHNL2 (1 << 18) /* Rx channel 2 (3945 only) */
-#define CSR_FH_INT_BIT_RX_CHNL1 (1 << 17) /* Rx channel 1 */
-#define CSR_FH_INT_BIT_RX_CHNL0 (1 << 16) /* Rx channel 0 */
-#define CSR_FH_INT_BIT_TX_CHNL6 (1 << 6) /* Tx channel 6 (3945 only) */
-#define CSR_FH_INT_BIT_TX_CHNL1 (1 << 1) /* Tx channel 1 */
-#define CSR_FH_INT_BIT_TX_CHNL0 (1 << 0) /* Tx channel 0 */
-
-#define CSR_FH_INT_RX_MASK (CSR_FH_INT_BIT_HI_PRIOR | \
- CSR_FH_INT_BIT_RX_CHNL2 | \
- CSR_FH_INT_BIT_RX_CHNL1 | \
- CSR_FH_INT_BIT_RX_CHNL0)
-
-#define CSR_FH_INT_TX_MASK (CSR_FH_INT_BIT_TX_CHNL6 | \
- CSR_FH_INT_BIT_TX_CHNL1 | \
- CSR_FH_INT_BIT_TX_CHNL0)
-
-
-/* RESET */
-#define CSR_RESET_REG_FLAG_NEVO_RESET (0x00000001)
-#define CSR_RESET_REG_FLAG_FORCE_NMI (0x00000002)
-#define CSR_RESET_REG_FLAG_SW_RESET (0x00000080)
-#define CSR_RESET_REG_FLAG_MASTER_DISABLED (0x00000100)
-#define CSR_RESET_REG_FLAG_STOP_MASTER (0x00000200)
-
-/* GP (general purpose) CONTROL */
-#define CSR_GP_CNTRL_REG_FLAG_MAC_CLOCK_READY (0x00000001)
-#define CSR_GP_CNTRL_REG_FLAG_INIT_DONE (0x00000004)
-#define CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ (0x00000008)
-#define CSR_GP_CNTRL_REG_FLAG_GOING_TO_SLEEP (0x00000010)
-
-#define CSR_GP_CNTRL_REG_VAL_MAC_ACCESS_EN (0x00000001)
-
-#define CSR_GP_CNTRL_REG_MSK_POWER_SAVE_TYPE (0x07000000)
-#define CSR_GP_CNTRL_REG_FLAG_MAC_POWER_SAVE (0x04000000)
-#define CSR_GP_CNTRL_REG_FLAG_HW_RF_KILL_SW (0x08000000)
-
-
-/* EEPROM REG */
-#define CSR_EEPROM_REG_READ_VALID_MSK (0x00000001)
-#define CSR_EEPROM_REG_BIT_CMD (0x00000002)
-
-/* EEPROM GP */
-#define CSR_EEPROM_GP_VALID_MSK (0x00000006)
-#define CSR_EEPROM_GP_BAD_SIGNATURE (0x00000000)
-#define CSR_EEPROM_GP_IF_OWNER_MSK (0x00000180)
-
-/* UCODE DRV GP */
-#define CSR_UCODE_DRV_GP1_BIT_MAC_SLEEP (0x00000001)
-#define CSR_UCODE_SW_BIT_RFKILL (0x00000002)
-#define CSR_UCODE_DRV_GP1_BIT_CMD_BLOCKED (0x00000004)
-#define CSR_UCODE_DRV_GP1_REG_BIT_CT_KILL_EXIT (0x00000008)
-
-/* GPIO */
-#define CSR_GPIO_IN_BIT_AUX_POWER (0x00000200)
-#define CSR_GPIO_IN_VAL_VAUX_PWR_SRC (0x00000000)
-#define CSR_GPIO_IN_VAL_VMAIN_PWR_SRC CSR_GPIO_IN_BIT_AUX_POWER
-
-/* GI Chicken Bits */
-#define CSR_GIO_CHICKEN_BITS_REG_BIT_L1A_NO_L0S_RX (0x00800000)
-#define CSR_GIO_CHICKEN_BITS_REG_BIT_DIS_L0S_EXIT_TIMER (0x20000000)
-
-/* CSR_ANA_PLL_CFG */
-#define CSR_ANA_PLL_CFG_SH (0x00880300)
-
/*=== HBUS (Host-side Bus) ===*/
#define HBUS_BASE (0x400)
if (rev_id & PCI_CFG_REV_ID_BIT_RTP)
IWL_DEBUG_INFO("RTP type \n");
else if (rev_id & PCI_CFG_REV_ID_BIT_BASIC_SKU) {
- IWL_DEBUG_INFO("ALM-MB type\n");
+ IWL_DEBUG_INFO("3945 RADIO-MB type\n");
iwl3945_set_bit(priv, CSR_HW_IF_CONFIG_REG,
- CSR_HW_IF_CONFIG_REG_BIT_ALMAGOR_MB);
+ CSR39_HW_IF_CONFIG_REG_BIT_3945_MB);
} else {
- IWL_DEBUG_INFO("ALM-MM type\n");
+ IWL_DEBUG_INFO("3945 RADIO-MM type\n");
iwl3945_set_bit(priv, CSR_HW_IF_CONFIG_REG,
- CSR_HW_IF_CONFIG_REG_BIT_ALMAGOR_MM);
+ CSR39_HW_IF_CONFIG_REG_BIT_3945_MM);
}
if (EEPROM_SKU_CAP_OP_MODE_MRC == priv->eeprom.sku_cap) {
IWL_DEBUG_INFO("SKU OP mode is mrc\n");
iwl3945_set_bit(priv, CSR_HW_IF_CONFIG_REG,
- CSR_HW_IF_CONFIG_REG_BIT_SKU_MRC);
+ CSR39_HW_IF_CONFIG_REG_BIT_SKU_MRC);
} else
IWL_DEBUG_INFO("SKU OP mode is basic\n");
IWL_DEBUG_INFO("3945ABG revision is 0x%X\n",
priv->eeprom.board_revision);
iwl3945_set_bit(priv, CSR_HW_IF_CONFIG_REG,
- CSR_HW_IF_CONFIG_REG_BIT_BOARD_TYPE);
+ CSR39_HW_IF_CONFIG_REG_BIT_BOARD_TYPE);
} else {
IWL_DEBUG_INFO("3945ABG revision is 0x%X\n",
priv->eeprom.board_revision);
iwl3945_clear_bit(priv, CSR_HW_IF_CONFIG_REG,
- CSR_HW_IF_CONFIG_REG_BIT_BOARD_TYPE);
+ CSR39_HW_IF_CONFIG_REG_BIT_BOARD_TYPE);
}
if (priv->eeprom.almgor_m_version <= 1) {
iwl3945_set_bit(priv, CSR_HW_IF_CONFIG_REG,
- CSR_HW_IF_CONFIG_REG_BITS_SILICON_TYPE_A);
+ CSR39_HW_IF_CONFIG_REG_BITS_SILICON_TYPE_A);
IWL_DEBUG_INFO("Card M type A version is 0x%X\n",
priv->eeprom.almgor_m_version);
} else {
IWL_DEBUG_INFO("Card M type B version is 0x%X\n",
priv->eeprom.almgor_m_version);
iwl3945_set_bit(priv, CSR_HW_IF_CONFIG_REG,
- CSR_HW_IF_CONFIG_REG_BITS_SILICON_TYPE_B);
+ CSR39_HW_IF_CONFIG_REG_BITS_SILICON_TYPE_B);
}
spin_unlock_irqrestore(&priv->lock, flags);
extern struct pci_device_id iwl3945_hw_card_ids[];
#define DRV_NAME "iwl3945"
-#include "iwl-3945-hw.h"
+#include "iwl-csr.h"
#include "iwl-prph.h"
+#include "iwl-3945-hw.h"
#include "iwl-3945-debug.h"
/* Default noise level to report when noise measurement is not available.
#define PCI_REG_WUM8 0x0E8
#define PCI_CFG_PMC_PME_FROM_D3COLD_SUPPORT (0x80000000)
-/*=== CSR (control and status registers) ===*/
-#define CSR_BASE (0x000)
-
-#define CSR_HW_IF_CONFIG_REG (CSR_BASE+0x000) /* hardware interface config */
-#define CSR_INT_COALESCING (CSR_BASE+0x004) /* accum ints, 32-usec units */
-#define CSR_INT (CSR_BASE+0x008) /* host interrupt status/ack */
-#define CSR_INT_MASK (CSR_BASE+0x00c) /* host interrupt enable */
-#define CSR_FH_INT_STATUS (CSR_BASE+0x010) /* busmaster int status/ack*/
-#define CSR_GPIO_IN (CSR_BASE+0x018) /* read external chip pins */
-#define CSR_RESET (CSR_BASE+0x020) /* busmaster enable, NMI, etc*/
-#define CSR_GP_CNTRL (CSR_BASE+0x024)
-
-/*
- * Hardware revision info
- * Bit fields:
- * 31-8: Reserved
- * 7-4: Type of device: 0x0 = 4965, 0xd = 3945
- * 3-2: Revision step: 0 = A, 1 = B, 2 = C, 3 = D
- * 1-0: "Dash" value, as in A-1, etc.
- *
- * NOTE: Revision step affects calculation of CCK txpower for 4965.
- */
-#define CSR_HW_REV (CSR_BASE+0x028)
-
-/* EEPROM reads */
-#define CSR_EEPROM_REG (CSR_BASE+0x02c)
-#define CSR_EEPROM_GP (CSR_BASE+0x030)
-#define CSR_GP_UCODE (CSR_BASE+0x044)
-#define CSR_UCODE_DRV_GP1 (CSR_BASE+0x054)
-#define CSR_UCODE_DRV_GP1_SET (CSR_BASE+0x058)
-#define CSR_UCODE_DRV_GP1_CLR (CSR_BASE+0x05c)
-#define CSR_UCODE_DRV_GP2 (CSR_BASE+0x060)
-#define CSR_GIO_CHICKEN_BITS (CSR_BASE+0x100)
-
-/*
- * Indicates hardware rev, to determine CCK backoff for txpower calculation.
- * Bit fields:
- * 3-2: 0 = A, 1 = B, 2 = C, 3 = D step
- */
-#define CSR_HW_REV_WA_REG (CSR_BASE+0x22C)
-
-/* Hardware interface configuration bits */
-#define CSR_HW_IF_CONFIG_REG_BIT_KEDRON_R (0x00000010)
-#define CSR_HW_IF_CONFIG_REG_MSK_BOARD_VER (0x00000C00)
-#define CSR_HW_IF_CONFIG_REG_BIT_MAC_SI (0x00000100)
-#define CSR_HW_IF_CONFIG_REG_BIT_RADIO_SI (0x00000200)
-#define CSR_HW_IF_CONFIG_REG_BIT_EEPROM_OWN_SEM (0x00200000)
-
-/* interrupt flags in INTA, set by uCode or hardware (e.g. dma),
- * acknowledged (reset) by host writing "1" to flagged bits. */
-#define CSR_INT_BIT_FH_RX (1 << 31) /* Rx DMA, cmd responses, FH_INT[17:16] */
-#define CSR_INT_BIT_HW_ERR (1 << 29) /* DMA hardware error FH_INT[31] */
-#define CSR_INT_BIT_DNLD (1 << 28) /* uCode Download */
-#define CSR_INT_BIT_FH_TX (1 << 27) /* Tx DMA FH_INT[1:0] */
-#define CSR_INT_BIT_SCD (1 << 26) /* TXQ pointer advanced */
-#define CSR_INT_BIT_SW_ERR (1 << 25) /* uCode error */
-#define CSR_INT_BIT_RF_KILL (1 << 7) /* HW RFKILL switch GP_CNTRL[27] toggled */
-#define CSR_INT_BIT_CT_KILL (1 << 6) /* Critical temp (chip too hot) rfkill */
-#define CSR_INT_BIT_SW_RX (1 << 3) /* Rx, command responses, 3945 */
-#define CSR_INT_BIT_WAKEUP (1 << 1) /* NIC controller waking up (pwr mgmt) */
-#define CSR_INT_BIT_ALIVE (1 << 0) /* uCode interrupts once it initializes */
-
-#define CSR_INI_SET_MASK (CSR_INT_BIT_FH_RX | \
- CSR_INT_BIT_HW_ERR | \
- CSR_INT_BIT_FH_TX | \
- CSR_INT_BIT_SW_ERR | \
- CSR_INT_BIT_RF_KILL | \
- CSR_INT_BIT_SW_RX | \
- CSR_INT_BIT_WAKEUP | \
- CSR_INT_BIT_ALIVE)
-
-/* interrupt flags in FH (flow handler) (PCI busmaster DMA) */
-#define CSR_FH_INT_BIT_ERR (1 << 31) /* Error */
-#define CSR_FH_INT_BIT_HI_PRIOR (1 << 30) /* High priority Rx, bypass coalescing */
-#define CSR_FH_INT_BIT_RX_CHNL1 (1 << 17) /* Rx channel 1 */
-#define CSR_FH_INT_BIT_RX_CHNL0 (1 << 16) /* Rx channel 0 */
-#define CSR_FH_INT_BIT_TX_CHNL1 (1 << 1) /* Tx channel 1 */
-#define CSR_FH_INT_BIT_TX_CHNL0 (1 << 0) /* Tx channel 0 */
-
-#define CSR_FH_INT_RX_MASK (CSR_FH_INT_BIT_HI_PRIOR | \
- CSR_FH_INT_BIT_RX_CHNL1 | \
- CSR_FH_INT_BIT_RX_CHNL0)
-
-#define CSR_FH_INT_TX_MASK (CSR_FH_INT_BIT_TX_CHNL1 | \
- CSR_FH_INT_BIT_TX_CHNL0)
-
-
-/* RESET */
-#define CSR_RESET_REG_FLAG_NEVO_RESET (0x00000001)
-#define CSR_RESET_REG_FLAG_FORCE_NMI (0x00000002)
-#define CSR_RESET_REG_FLAG_SW_RESET (0x00000080)
-#define CSR_RESET_REG_FLAG_MASTER_DISABLED (0x00000100)
-#define CSR_RESET_REG_FLAG_STOP_MASTER (0x00000200)
-
-/* GP (general purpose) CONTROL */
-#define CSR_GP_CNTRL_REG_FLAG_MAC_CLOCK_READY (0x00000001)
-#define CSR_GP_CNTRL_REG_FLAG_INIT_DONE (0x00000004)
-#define CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ (0x00000008)
-#define CSR_GP_CNTRL_REG_FLAG_GOING_TO_SLEEP (0x00000010)
-
-#define CSR_GP_CNTRL_REG_VAL_MAC_ACCESS_EN (0x00000001)
-
-#define CSR_GP_CNTRL_REG_MSK_POWER_SAVE_TYPE (0x07000000)
-#define CSR_GP_CNTRL_REG_FLAG_MAC_POWER_SAVE (0x04000000)
-#define CSR_GP_CNTRL_REG_FLAG_HW_RF_KILL_SW (0x08000000)
-
-
-/* EEPROM REG */
-#define CSR_EEPROM_REG_READ_VALID_MSK (0x00000001)
-#define CSR_EEPROM_REG_BIT_CMD (0x00000002)
-
-/* EEPROM GP */
-#define CSR_EEPROM_GP_VALID_MSK (0x00000006)
-#define CSR_EEPROM_GP_BAD_SIGNATURE (0x00000000)
-#define CSR_EEPROM_GP_IF_OWNER_MSK (0x00000180)
-
-/* UCODE DRV GP */
-#define CSR_UCODE_DRV_GP1_BIT_MAC_SLEEP (0x00000001)
-#define CSR_UCODE_SW_BIT_RFKILL (0x00000002)
-#define CSR_UCODE_DRV_GP1_BIT_CMD_BLOCKED (0x00000004)
-#define CSR_UCODE_DRV_GP1_REG_BIT_CT_KILL_EXIT (0x00000008)
-
-/* GPIO */
-#define CSR_GPIO_IN_BIT_AUX_POWER (0x00000200)
-#define CSR_GPIO_IN_VAL_VAUX_PWR_SRC (0x00000000)
-#define CSR_GPIO_IN_VAL_VMAIN_PWR_SRC CSR_GPIO_IN_BIT_AUX_POWER
-
-/* GI Chicken Bits */
-#define CSR_GIO_CHICKEN_BITS_REG_BIT_L1A_NO_L0S_RX (0x00800000)
-#define CSR_GIO_CHICKEN_BITS_REG_BIT_DIS_L0S_EXIT_TIMER (0x20000000)
-
/*=== HBUS (Host-side Bus) ===*/
#define HBUS_BASE (0x400)
/* set CSR_HW_CONFIG_REG for uCode use */
iwl4965_set_bit(priv, CSR_HW_IF_CONFIG_REG,
- CSR_HW_IF_CONFIG_REG_BIT_KEDRON_R |
- CSR_HW_IF_CONFIG_REG_BIT_RADIO_SI |
- CSR_HW_IF_CONFIG_REG_BIT_MAC_SI);
+ CSR49_HW_IF_CONFIG_REG_BIT_4965_R |
+ CSR49_HW_IF_CONFIG_REG_BIT_RADIO_SI |
+ CSR49_HW_IF_CONFIG_REG_BIT_MAC_SI);
rc = iwl4965_grab_nic_access(priv);
if (rc < 0) {
#define DRV_NAME "iwl4965"
#include "iwl-4965-hw.h"
+#include "iwl-csr.h"
#include "iwl-prph.h"
#include "iwl-4965-debug.h"
--- /dev/null
+/******************************************************************************
+ *
+ * This file is provided under a dual BSD/GPLv2 license. When using or
+ * redistributing this file, you may do so under either license.
+ *
+ * GPL LICENSE SUMMARY
+ *
+ * Copyright(c) 2005 - 2008 Intel Corporation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of version 2 of the GNU General Public License as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110,
+ * USA
+ *
+ * The full GNU General Public License is included in this distribution
+ * in the file called LICENSE.GPL.
+ *
+ * Contact Information:
+ * James P. Ketrenos <ipw2100-admin@linux.intel.com>
+ * Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+ *
+ * BSD LICENSE
+ *
+ * Copyright(c) 2005 - 2007 Intel Corporation. All rights reserved.
+ * All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in
+ * the documentation and/or other materials provided with the
+ * distribution.
+ * * Neither the name Intel Corporation nor the names of its
+ * contributors may be used to endorse or promote products derived
+ * from this software without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ *****************************************************************************/
+/*=== CSR (control and status registers) ===*/
+#define CSR_BASE (0x000)
+
+#define CSR_HW_IF_CONFIG_REG (CSR_BASE+0x000) /* hardware interface config */
+#define CSR_INT_COALESCING (CSR_BASE+0x004) /* accum ints, 32-usec units */
+#define CSR_INT (CSR_BASE+0x008) /* host interrupt status/ack */
+#define CSR_INT_MASK (CSR_BASE+0x00c) /* host interrupt enable */
+#define CSR_FH_INT_STATUS (CSR_BASE+0x010) /* busmaster int status/ack*/
+#define CSR_GPIO_IN (CSR_BASE+0x018) /* read external chip pins */
+#define CSR_RESET (CSR_BASE+0x020) /* busmaster enable, NMI, etc*/
+#define CSR_GP_CNTRL (CSR_BASE+0x024)
+
+/*
+ * Hardware revision info
+ * Bit fields:
+ * 31-8: Reserved
+ * 7-4: Type of device: 0x0 = 4965, 0xd = 3945
+ * 3-2: Revision step: 0 = A, 1 = B, 2 = C, 3 = D
+ * 1-0: "Dash" value, as in A-1, etc.
+ *
+ * NOTE: Revision step affects calculation of CCK txpower for 4965.
+ */
+#define CSR_HW_REV (CSR_BASE+0x028)
+
+/* EEPROM reads */
+#define CSR_EEPROM_REG (CSR_BASE+0x02c)
+#define CSR_EEPROM_GP (CSR_BASE+0x030)
+#define CSR_GP_UCODE (CSR_BASE+0x044)
+#define CSR_UCODE_DRV_GP1 (CSR_BASE+0x054)
+#define CSR_UCODE_DRV_GP1_SET (CSR_BASE+0x058)
+#define CSR_UCODE_DRV_GP1_CLR (CSR_BASE+0x05c)
+#define CSR_UCODE_DRV_GP2 (CSR_BASE+0x060)
+#define CSR_GIO_CHICKEN_BITS (CSR_BASE+0x100)
+
+/* Analog phase-lock-loop configuration (3945 only)
+ * Set bit 24. */
+#define CSR_ANA_PLL_CFG (CSR_BASE+0x20c)
+/*
+ * Indicates hardware rev, to determine CCK backoff for txpower calculation.
+ * Bit fields:
+ * 3-2: 0 = A, 1 = B, 2 = C, 3 = D step
+ */
+#define CSR_HW_REV_WA_REG (CSR_BASE+0x22C)
+
+/* Bits for CSR_HW_IF_CONFIG_REG */
+#define CSR49_HW_IF_CONFIG_REG_BIT_4965_R (0x00000010)
+#define CSR49_HW_IF_CONFIG_REG_MSK_BOARD_VER (0x00000C00)
+#define CSR49_HW_IF_CONFIG_REG_BIT_MAC_SI (0x00000100)
+#define CSR49_HW_IF_CONFIG_REG_BIT_RADIO_SI (0x00000200)
+
+#define CSR39_HW_IF_CONFIG_REG_BIT_3945_MB (0x00000100)
+#define CSR39_HW_IF_CONFIG_REG_BIT_3945_MM (0x00000200)
+#define CSR39_HW_IF_CONFIG_REG_BIT_SKU_MRC (0x00000400)
+#define CSR39_HW_IF_CONFIG_REG_BIT_BOARD_TYPE (0x00000800)
+#define CSR39_HW_IF_CONFIG_REG_BITS_SILICON_TYPE_A (0x00000000)
+#define CSR39_HW_IF_CONFIG_REG_BITS_SILICON_TYPE_B (0x00001000)
+
+#define CSR_HW_IF_CONFIG_REG_BIT_EEPROM_OWN_SEM (0x00200000)
+
+/* interrupt flags in INTA, set by uCode or hardware (e.g. dma),
+ * acknowledged (reset) by host writing "1" to flagged bits. */
+#define CSR_INT_BIT_FH_RX (1 << 31) /* Rx DMA, cmd responses, FH_INT[17:16] */
+#define CSR_INT_BIT_HW_ERR (1 << 29) /* DMA hardware error FH_INT[31] */
+#define CSR_INT_BIT_DNLD (1 << 28) /* uCode Download */
+#define CSR_INT_BIT_FH_TX (1 << 27) /* Tx DMA FH_INT[1:0] */
+#define CSR_INT_BIT_SCD (1 << 26) /* TXQ pointer advanced */
+#define CSR_INT_BIT_SW_ERR (1 << 25) /* uCode error */
+#define CSR_INT_BIT_RF_KILL (1 << 7) /* HW RFKILL switch GP_CNTRL[27] toggled */
+#define CSR_INT_BIT_CT_KILL (1 << 6) /* Critical temp (chip too hot) rfkill */
+#define CSR_INT_BIT_SW_RX (1 << 3) /* Rx, command responses, 3945 */
+#define CSR_INT_BIT_WAKEUP (1 << 1) /* NIC controller waking up (pwr mgmt) */
+#define CSR_INT_BIT_ALIVE (1 << 0) /* uCode interrupts once it initializes */
+
+#define CSR_INI_SET_MASK (CSR_INT_BIT_FH_RX | \
+ CSR_INT_BIT_HW_ERR | \
+ CSR_INT_BIT_FH_TX | \
+ CSR_INT_BIT_SW_ERR | \
+ CSR_INT_BIT_RF_KILL | \
+ CSR_INT_BIT_SW_RX | \
+ CSR_INT_BIT_WAKEUP | \
+ CSR_INT_BIT_ALIVE)
+
+/* interrupt flags in FH (flow handler) (PCI busmaster DMA) */
+#define CSR_FH_INT_BIT_ERR (1 << 31) /* Error */
+#define CSR_FH_INT_BIT_HI_PRIOR (1 << 30) /* High priority Rx, bypass coalescing */
+#define CSR39_FH_INT_BIT_RX_CHNL2 (1 << 18) /* Rx channel 2 (3945 only) */
+#define CSR_FH_INT_BIT_RX_CHNL1 (1 << 17) /* Rx channel 1 */
+#define CSR_FH_INT_BIT_RX_CHNL0 (1 << 16) /* Rx channel 0 */
+#define CSR39_FH_INT_BIT_TX_CHNL6 (1 << 6) /* Tx channel 6 (3945 only) */
+#define CSR_FH_INT_BIT_TX_CHNL1 (1 << 1) /* Tx channel 1 */
+#define CSR_FH_INT_BIT_TX_CHNL0 (1 << 0) /* Tx channel 0 */
+
+#define CSR39_FH_INT_RX_MASK (CSR_FH_INT_BIT_HI_PRIOR | \
+ CSR39_FH_INT_BIT_RX_CHNL2 | \
+ CSR_FH_INT_BIT_RX_CHNL1 | \
+ CSR_FH_INT_BIT_RX_CHNL0)
+
+
+#define CSR39_FH_INT_TX_MASK (CSR39_FH_INT_BIT_TX_CHNL6 | \
+ CSR_FH_INT_BIT_TX_CHNL1 | \
+ CSR_FH_INT_BIT_TX_CHNL0)
+
+#define CSR49_FH_INT_RX_MASK (CSR_FH_INT_BIT_HI_PRIOR | \
+ CSR_FH_INT_BIT_RX_CHNL1 | \
+ CSR_FH_INT_BIT_RX_CHNL0)
+
+#define CSR49_FH_INT_TX_MASK (CSR_FH_INT_BIT_TX_CHNL1 | \
+ CSR_FH_INT_BIT_TX_CHNL0)
+
+
+/* RESET */
+#define CSR_RESET_REG_FLAG_NEVO_RESET (0x00000001)
+#define CSR_RESET_REG_FLAG_FORCE_NMI (0x00000002)
+#define CSR_RESET_REG_FLAG_SW_RESET (0x00000080)
+#define CSR_RESET_REG_FLAG_MASTER_DISABLED (0x00000100)
+#define CSR_RESET_REG_FLAG_STOP_MASTER (0x00000200)
+
+/* GP (general purpose) CONTROL */
+#define CSR_GP_CNTRL_REG_FLAG_MAC_CLOCK_READY (0x00000001)
+#define CSR_GP_CNTRL_REG_FLAG_INIT_DONE (0x00000004)
+#define CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ (0x00000008)
+#define CSR_GP_CNTRL_REG_FLAG_GOING_TO_SLEEP (0x00000010)
+
+#define CSR_GP_CNTRL_REG_VAL_MAC_ACCESS_EN (0x00000001)
+
+#define CSR_GP_CNTRL_REG_MSK_POWER_SAVE_TYPE (0x07000000)
+#define CSR_GP_CNTRL_REG_FLAG_MAC_POWER_SAVE (0x04000000)
+#define CSR_GP_CNTRL_REG_FLAG_HW_RF_KILL_SW (0x08000000)
+
+
+/* EEPROM REG */
+#define CSR_EEPROM_REG_READ_VALID_MSK (0x00000001)
+#define CSR_EEPROM_REG_BIT_CMD (0x00000002)
+
+/* EEPROM GP */
+#define CSR_EEPROM_GP_VALID_MSK (0x00000006)
+#define CSR_EEPROM_GP_BAD_SIGNATURE (0x00000000)
+#define CSR_EEPROM_GP_IF_OWNER_MSK (0x00000180)
+
+/* UCODE DRV GP */
+#define CSR_UCODE_DRV_GP1_BIT_MAC_SLEEP (0x00000001)
+#define CSR_UCODE_SW_BIT_RFKILL (0x00000002)
+#define CSR_UCODE_DRV_GP1_BIT_CMD_BLOCKED (0x00000004)
+#define CSR_UCODE_DRV_GP1_REG_BIT_CT_KILL_EXIT (0x00000008)
+
+/* GPIO */
+#define CSR_GPIO_IN_BIT_AUX_POWER (0x00000200)
+#define CSR_GPIO_IN_VAL_VAUX_PWR_SRC (0x00000000)
+#define CSR_GPIO_IN_VAL_VMAIN_PWR_SRC CSR_GPIO_IN_BIT_AUX_POWER
+
+/* GI Chicken Bits */
+#define CSR_GIO_CHICKEN_BITS_REG_BIT_L1A_NO_L0S_RX (0x00800000)
+#define CSR_GIO_CHICKEN_BITS_REG_BIT_DIS_L0S_EXIT_TIMER (0x20000000)
+
+
* atomic, make sure that inta covers all the interrupts that
* we've discovered, even if FH interrupt came in just after
* reading CSR_INT. */
- if (inta_fh & CSR_FH_INT_RX_MASK)
+ if (inta_fh & CSR39_FH_INT_RX_MASK)
inta |= CSR_INT_BIT_FH_RX;
- if (inta_fh & CSR_FH_INT_TX_MASK)
+ if (inta_fh & CSR39_FH_INT_TX_MASK)
inta |= CSR_INT_BIT_FH_TX;
/* Now service all interrupt bits discovered above. */
* atomic, make sure that inta covers all the interrupts that
* we've discovered, even if FH interrupt came in just after
* reading CSR_INT. */
- if (inta_fh & CSR_FH_INT_RX_MASK)
+ if (inta_fh & CSR49_FH_INT_RX_MASK)
inta |= CSR_INT_BIT_FH_RX;
- if (inta_fh & CSR_FH_INT_TX_MASK)
+ if (inta_fh & CSR49_FH_INT_TX_MASK)
inta |= CSR_INT_BIT_FH_TX;
/* Now service all interrupt bits discovered above. */
projects / linux-2.6 / commitdiff