--- /dev/null
+/*
+ w83793.c - Linux kernel driver for hardware monitoring
+ Copyright (C) 2006 Winbond Electronics Corp.
+ Yuan Mu
+ Rudolf Marek <r.marek@assembler.cz>
+
+ This program is free software; you can redistribute it and/or modify
+ it under the terms of the GNU General Public License as published by
+ the Free Software Foundation - version 2.
+
+ This program is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ GNU General Public License for more details.
+
+ You should have received a copy of the GNU General Public License
+ along with this program; if not, write to the Free Software
+ Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
+ 02110-1301 USA.
+*/
+
+/*
+ Supports following chips:
+
+ Chip #vin #fanin #pwm #temp wchipid vendid i2c ISA
+ w83793 10 12 8 6 0x7b 0x5ca3 yes no
+*/
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/i2c.h>
+#include <linux/hwmon.h>
+#include <linux/hwmon-vid.h>
+#include <linux/hwmon-sysfs.h>
+#include <linux/err.h>
+#include <linux/mutex.h>
+
+/* Addresses to scan */
+static unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, 0x2f, I2C_CLIENT_END };
+
+/* Insmod parameters */
+I2C_CLIENT_INSMOD_1(w83793);
+I2C_CLIENT_MODULE_PARM(force_subclients, "List of subclient addresses: "
+ "{bus, clientaddr, subclientaddr1, subclientaddr2}");
+
+static int reset;
+module_param(reset, bool, 0);
+MODULE_PARM_DESC(reset, "Set to 1 to reset chip, not recommended");
+
+/*
+ Address 0x00, 0x0d, 0x0e, 0x0f in all three banks are reserved
+ as ID, Bank Select registers
+*/
+#define W83793_REG_BANKSEL 0x00
+#define W83793_REG_VENDORID 0x0d
+#define W83793_REG_CHIPID 0x0e
+#define W83793_REG_DEVICEID 0x0f
+
+#define W83793_REG_CONFIG 0x40
+#define W83793_REG_MFC 0x58
+#define W83793_REG_FANIN_CTRL 0x5c
+#define W83793_REG_FANIN_SEL 0x5d
+#define W83793_REG_I2C_ADDR 0x0b
+#define W83793_REG_I2C_SUBADDR 0x0c
+#define W83793_REG_VID_INA 0x05
+#define W83793_REG_VID_INB 0x06
+#define W83793_REG_VID_LATCHA 0x07
+#define W83793_REG_VID_LATCHB 0x08
+#define W83793_REG_VID_CTRL 0x59
+
+static u16 W83793_REG_TEMP_MODE[2] = { 0x5e, 0x5f };
+
+#define TEMP_READ 0
+#define TEMP_CRIT 1
+#define TEMP_CRIT_HYST 2
+#define TEMP_WARN 3
+#define TEMP_WARN_HYST 4
+/* only crit and crit_hyst affect real-time alarm status
+ current crit crit_hyst warn warn_hyst */
+static u16 W83793_REG_TEMP[][5] = {
+ {0x1c, 0x78, 0x79, 0x7a, 0x7b},
+ {0x1d, 0x7c, 0x7d, 0x7e, 0x7f},
+ {0x1e, 0x80, 0x81, 0x82, 0x83},
+ {0x1f, 0x84, 0x85, 0x86, 0x87},
+ {0x20, 0x88, 0x89, 0x8a, 0x8b},
+ {0x21, 0x8c, 0x8d, 0x8e, 0x8f},
+};
+
+#define W83793_REG_TEMP_LOW_BITS 0x22
+
+#define W83793_REG_BEEP(index) (0x53 + (index))
+#define W83793_REG_ALARM(index) (0x4b + (index))
+
+#define W83793_REG_CLR_CHASSIS 0x4a /* SMI MASK4 */
+#define W83793_REG_IRQ_CTRL 0x50
+#define W83793_REG_OVT_CTRL 0x51
+#define W83793_REG_OVT_BEEP 0x52
+
+#define IN_READ 0
+#define IN_MAX 1
+#define IN_LOW 2
+static const u16 W83793_REG_IN[][3] = {
+ /* Current, High, Low */
+ {0x10, 0x60, 0x61}, /* Vcore A */
+ {0x11, 0x62, 0x63}, /* Vcore B */
+ {0x12, 0x64, 0x65}, /* Vtt */
+ {0x14, 0x6a, 0x6b}, /* VSEN1 */
+ {0x15, 0x6c, 0x6d}, /* VSEN2 */
+ {0x16, 0x6e, 0x6f}, /* +3VSEN */
+ {0x17, 0x70, 0x71}, /* +12VSEN */
+ {0x18, 0x72, 0x73}, /* 5VDD */
+ {0x19, 0x74, 0x75}, /* 5VSB */
+ {0x1a, 0x76, 0x77}, /* VBAT */
+};
+
+/* Low Bits of Vcore A/B Vtt Read/High/Low */
+static const u16 W83793_REG_IN_LOW_BITS[] = { 0x1b, 0x68, 0x69 };
+static u8 scale_in[] = { 2, 2, 2, 16, 16, 16, 8, 24, 24, 16 };
+
+#define W83793_REG_FAN(index) (0x23 + 2 * (index)) /* High byte */
+#define W83793_REG_FAN_MIN(index) (0x90 + 2 * (index)) /* High byte */
+
+#define W83793_REG_PWM_DEFAULT 0xb2
+#define W83793_REG_PWM_ENABLE 0x207
+#define W83793_REG_PWM_UPTIME 0xc3 /* Unit in 0.1 second */
+#define W83793_REG_PWM_DOWNTIME 0xc4 /* Unit in 0.1 second */
+#define W83793_REG_TEMP_CRITICAL 0xc5
+
+#define PWM_DUTY 0
+#define PWM_START 1
+#define PWM_NONSTOP 2
+#define W83793_REG_PWM(index, nr) (((nr) == 0 ? 0xb3 : \
+ (nr) == 1 ? 0x220 : 0x218) + (index))
+
+/* bit field, fan1 is bit0, fan2 is bit1 ... */
+#define W83793_REG_TEMP_FAN_MAP(index) (0x201 + (index))
+#define W83793_REG_TEMP_TOL(index) (0x208 + (index))
+#define W83793_REG_TEMP_CRUISE(index) (0x210 + (index))
+#define W83793_REG_PWM_STOP_TIME(index) (0x228 + (index))
+#define W83793_REG_SF2_TEMP(index, nr) (0x230 + ((index) << 4) + (nr))
+#define W83793_REG_SF2_PWM(index, nr) (0x238 + ((index) << 4) + (nr))
+
+static inline unsigned long FAN_FROM_REG(u16 val)
+{
+ if ((val >= 0xfff) || (val == 0))
+ return 0;
+ return (1350000UL / val);
+}
+
+static inline u16 FAN_TO_REG(long rpm)
+{
+ if (rpm <= 0)
+ return 0x0fff;
+ return SENSORS_LIMIT((1350000 + (rpm >> 1)) / rpm, 1, 0xffe);
+}
+
+static inline unsigned long TIME_FROM_REG(u8 reg)
+{
+ return (reg * 100);
+}
+
+static inline u8 TIME_TO_REG(unsigned long val)
+{
+ return SENSORS_LIMIT((val + 50) / 100, 0, 0xff);
+}
+
+static inline long TEMP_FROM_REG(s8 reg)
+{
+ return (reg * 1000);
+}
+
+static inline s8 TEMP_TO_REG(long val, s8 min, s8 max)
+{
+ return SENSORS_LIMIT((val + (val < 0 ? -500 : 500)) / 1000, min, max);
+}
+
+struct w83793_data {
+ struct i2c_client client;
+ struct i2c_client *lm75[2];
+ struct class_device *class_dev;
+ struct mutex update_lock;
+ char valid; /* !=0 if following fields are valid */
+ unsigned long last_updated; /* In jiffies */
+ unsigned long last_nonvolatile; /* In jiffies, last time we update the
+ nonvolatile registers */
+
+ u8 bank;
+ u8 vrm;
+ u8 vid[2];
+ u8 in[10][3]; /* Register value, read/high/low */
+ u8 in_low_bits[3]; /* Additional resolution for VCore A/B Vtt */
+
+ u16 has_fan; /* Only fan1- fan5 has own pins */
+ u16 fan[12]; /* Register value combine */
+ u16 fan_min[12]; /* Register value combine */
+
+ s8 temp[6][5]; /* current, crit, crit_hyst,warn, warn_hyst */
+ u8 temp_low_bits; /* Additional resolution TD1-TD4 */
+ u8 temp_mode[2]; /* byte 0: Temp D1-D4 mode each has 2 bits
+ byte 1: Temp R1,R2 mode, each has 1 bit */
+ u8 temp_critical; /* If reached all fan will be at full speed */
+ u8 temp_fan_map[6]; /* Temp controls which pwm fan, bit field */
+
+ u8 has_pwm;
+ u8 pwm_enable; /* Register value, each Temp has 1 bit */
+ u8 pwm_uptime; /* Register value */
+ u8 pwm_downtime; /* Register value */
+ u8 pwm_default; /* All fan default pwm, next poweron valid */
+ u8 pwm[8][3]; /* Register value */
+ u8 pwm_stop_time[8];
+ u8 temp_cruise[6];
+
+ u8 alarms[5]; /* realtime status registers */
+ u8 beeps[5];
+ u8 beep_enable;
+ u8 tolerance[3]; /* Temp tolerance(Smart Fan I/II) */
+ u8 sf2_pwm[6][7]; /* Smart FanII: Fan duty cycle */
+ u8 sf2_temp[6][7]; /* Smart FanII: Temp level point */
+};
+
+static u8 w83793_read_value(struct i2c_client *client, u16 reg);
+static int w83793_write_value(struct i2c_client *client, u16 reg, u8 value);
+static int w83793_attach_adapter(struct i2c_adapter *adapter);
+static int w83793_detect(struct i2c_adapter *adapter, int address, int kind);
+static int w83793_detach_client(struct i2c_client *client);
+static void w83793_init_client(struct i2c_client *client);
+static void w83793_update_nonvolatile(struct device *dev);
+static struct w83793_data *w83793_update_device(struct device *dev);
+
+static struct i2c_driver w83793_driver = {
+ .driver = {
+ .name = "w83793",
+ },
+ .attach_adapter = w83793_attach_adapter,
+ .detach_client = w83793_detach_client,
+};
+
+static ssize_t
+show_vrm(struct device *dev, struct device_attribute *attr, char *buf)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct w83793_data *data = i2c_get_clientdata(client);
+
+ return sprintf(buf, "%d\n", data->vrm);
+}
+
+static ssize_t
+show_vid(struct device *dev, struct device_attribute *attr, char *buf)
+{
+ struct w83793_data *data = w83793_update_device(dev);
+ struct sensor_device_attribute_2 *sensor_attr =
+ to_sensor_dev_attr_2(attr);
+ int index = sensor_attr->index;
+
+ return sprintf(buf, "%d\n", vid_from_reg(data->vid[index], data->vrm));
+}
+
+static ssize_t
+store_vrm(struct device *dev, struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct w83793_data *data = i2c_get_clientdata(client);
+
+ data->vrm = simple_strtoul(buf, NULL, 10);
+ return count;
+}
+
+#define ALARM_STATUS 0
+#define BEEP_ENABLE 1
+static ssize_t
+show_alarm_beep(struct device *dev, struct device_attribute *attr, char *buf)
+{
+ struct w83793_data *data = w83793_update_device(dev);
+ struct sensor_device_attribute_2 *sensor_attr =
+ to_sensor_dev_attr_2(attr);
+ int nr = sensor_attr->nr;
+ int index = sensor_attr->index >> 3;
+ int bit = sensor_attr->index & 0x07;
+ u8 val;
+
+ if (ALARM_STATUS == nr) {
+ val = (data->alarms[index] >> (bit)) & 1;
+ } else { /* BEEP_ENABLE */
+ val = (data->beeps[index] >> (bit)) & 1;
+ }
+
+ return sprintf(buf, "%u\n", val);
+}
+
+static ssize_t
+store_beep(struct device *dev, struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct w83793_data *data = i2c_get_clientdata(client);
+ struct sensor_device_attribute_2 *sensor_attr =
+ to_sensor_dev_attr_2(attr);
+ int index = sensor_attr->index >> 3;
+ int shift = sensor_attr->index & 0x07;
+ u8 beep_bit = 1 << shift;
+ u8 val;
+
+ val = simple_strtoul(buf, NULL, 10);
+ if (val != 0 && val != 1)
+ return -EINVAL;
+
+ mutex_lock(&data->update_lock);
+ data->beeps[index] = w83793_read_value(client, W83793_REG_BEEP(index));
+ data->beeps[index] &= ~beep_bit;
+ data->beeps[index] |= val << shift;
+ w83793_write_value(client, W83793_REG_BEEP(index), data->beeps[index]);
+ mutex_unlock(&data->update_lock);
+
+ return count;
+}
+
+static ssize_t
+show_beep_enable(struct device *dev, struct device_attribute *attr, char *buf)
+{
+ struct w83793_data *data = w83793_update_device(dev);
+ return sprintf(buf, "%u\n", (data->beep_enable >> 1) & 0x01);
+}
+
+static ssize_t
+store_beep_enable(struct device *dev, struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct w83793_data *data = i2c_get_clientdata(client);
+ u8 val = simple_strtoul(buf, NULL, 10);
+
+ if (val != 0 && val != 1)
+ return -EINVAL;
+
+ mutex_lock(&data->update_lock);
+ data->beep_enable = w83793_read_value(client, W83793_REG_OVT_BEEP)
+ & 0xfd;
+ data->beep_enable |= val << 1;
+ w83793_write_value(client, W83793_REG_OVT_BEEP, data->beep_enable);
+ mutex_unlock(&data->update_lock);
+
+ return count;
+}
+
+/* Write any value to clear chassis alarm */
+static ssize_t
+store_chassis_clear(struct device *dev,
+ struct device_attribute *attr, const char *buf,
+ size_t count)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct w83793_data *data = i2c_get_clientdata(client);
+ u8 val;
+
+ mutex_lock(&data->update_lock);
+ val = w83793_read_value(client, W83793_REG_CLR_CHASSIS);
+ val |= 0x80;
+ w83793_write_value(client, W83793_REG_CLR_CHASSIS, val);
+ mutex_unlock(&data->update_lock);
+ return count;
+}
+
+#define FAN_INPUT 0
+#define FAN_MIN 1
+static ssize_t
+show_fan(struct device *dev, struct device_attribute *attr, char *buf)
+{
+ struct sensor_device_attribute_2 *sensor_attr =
+ to_sensor_dev_attr_2(attr);
+ int nr = sensor_attr->nr;
+ int index = sensor_attr->index;
+ struct w83793_data *data = w83793_update_device(dev);
+ u16 val;
+
+ if (FAN_INPUT == nr) {
+ val = data->fan[index] & 0x0fff;
+ } else {
+ val = data->fan_min[index] & 0x0fff;
+ }
+
+ return sprintf(buf, "%lu\n", FAN_FROM_REG(val));
+}
+
+static ssize_t
+store_fan_min(struct device *dev, struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct sensor_device_attribute_2 *sensor_attr =
+ to_sensor_dev_attr_2(attr);
+ int index = sensor_attr->index;
+ struct i2c_client *client = to_i2c_client(dev);
+ struct w83793_data *data = i2c_get_clientdata(client);
+ u16 val = FAN_TO_REG(simple_strtoul(buf, NULL, 10));
+
+ mutex_lock(&data->update_lock);
+ data->fan_min[index] = val;
+ w83793_write_value(client, W83793_REG_FAN_MIN(index),
+ (val >> 8) & 0xff);
+ w83793_write_value(client, W83793_REG_FAN_MIN(index) + 1, val & 0xff);
+ mutex_unlock(&data->update_lock);
+
+ return count;
+}
+
+#define PWM_DUTY 0
+#define PWM_START 1
+#define PWM_NONSTOP 2
+#define PWM_STOP_TIME 3
+static ssize_t
+show_pwm(struct device *dev, struct device_attribute *attr, char *buf)
+{
+ struct sensor_device_attribute_2 *sensor_attr =
+ to_sensor_dev_attr_2(attr);
+ struct w83793_data *data = w83793_update_device(dev);
+ u16 val;
+ int nr = sensor_attr->nr;
+ int index = sensor_attr->index;
+
+ if (PWM_STOP_TIME == nr)
+ val = TIME_FROM_REG(data->pwm_stop_time[index]);
+ else
+ val = (data->pwm[index][nr] & 0x3f) << 2;
+
+ return sprintf(buf, "%d\n", val);
+}
+
+static ssize_t
+store_pwm(struct device *dev, struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct w83793_data *data = i2c_get_clientdata(client);
+ struct sensor_device_attribute_2 *sensor_attr =
+ to_sensor_dev_attr_2(attr);
+ int nr = sensor_attr->nr;
+ int index = sensor_attr->index;
+ u8 val;
+
+ mutex_lock(&data->update_lock);
+ if (PWM_STOP_TIME == nr) {
+ val = TIME_TO_REG(simple_strtoul(buf, NULL, 10));
+ data->pwm_stop_time[index] = val;
+ w83793_write_value(client, W83793_REG_PWM_STOP_TIME(index),
+ val);
+ } else {
+ val = SENSORS_LIMIT(simple_strtoul(buf, NULL, 10), 0, 0xff)
+ >> 2;
+ data->pwm[index][nr] =
+ w83793_read_value(client, W83793_REG_PWM(index, nr)) & 0xc0;
+ data->pwm[index][nr] |= val;
+ w83793_write_value(client, W83793_REG_PWM(index, nr),
+ data->pwm[index][nr]);
+ }
+
+ mutex_unlock(&data->update_lock);
+ return count;
+}
+
+static ssize_t
+show_temp(struct device *dev, struct device_attribute *attr, char *buf)
+{
+ struct sensor_device_attribute_2 *sensor_attr =
+ to_sensor_dev_attr_2(attr);
+ int nr = sensor_attr->nr;
+ int index = sensor_attr->index;
+ struct w83793_data *data = w83793_update_device(dev);
+ long temp = TEMP_FROM_REG(data->temp[index][nr]);
+
+ if (TEMP_READ == nr && index < 4) { /* Only TD1-TD4 have low bits */
+ int low = ((data->temp_low_bits >> (index * 2)) & 0x03) * 250;
+ temp += temp > 0 ? low : -low;
+ }
+ return sprintf(buf, "%ld\n", temp);
+}
+
+static ssize_t
+store_temp(struct device *dev, struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct sensor_device_attribute_2 *sensor_attr =
+ to_sensor_dev_attr_2(attr);
+ int nr = sensor_attr->nr;
+ int index = sensor_attr->index;
+ struct i2c_client *client = to_i2c_client(dev);
+ struct w83793_data *data = i2c_get_clientdata(client);
+ long tmp = simple_strtol(buf, NULL, 10);
+
+ mutex_lock(&data->update_lock);
+ data->temp[index][nr] = TEMP_TO_REG(tmp, -128, 127);
+ w83793_write_value(client, W83793_REG_TEMP[index][nr],
+ data->temp[index][nr]);
+ mutex_unlock(&data->update_lock);
+ return count;
+}
+
+/*
+ TD1-TD4
+ each has 4 mode:(2 bits)
+ 0: Stop monitor
+ 1: Use internal temp sensor(default)
+ 2: Use sensor in AMD CPU and get result by AMDSI
+ 3: Use sensor in Intel CPU and get result by PECI
+
+ TR1-TR2
+ each has 2 mode:(1 bit)
+ 0: Disable temp sensor monitor
+ 1: To enable temp sensors monitor
+*/
+
+/* 0 disable, 5 AMDSI, 6 PECI */
+static u8 TO_TEMP_MODE[] = { 0, 0, 5, 6 };
+
+static ssize_t
+show_temp_mode(struct device *dev, struct device_attribute *attr, char *buf)
+{
+ struct w83793_data *data = w83793_update_device(dev);
+ struct sensor_device_attribute_2 *sensor_attr =
+ to_sensor_dev_attr_2(attr);
+ int index = sensor_attr->index;
+ u8 mask = (index < 4) ? 0x03 : 0x01;
+ u8 shift = (index < 4) ? (2 * index) : (index - 4);
+ u8 tmp;
+ index = (index < 4) ? 0 : 1;
+
+ tmp = (data->temp_mode[index] >> shift) & mask;
+
+ /* for the internal sensor, found out if diode or thermistor */
+ if (tmp == 1) {
+ tmp = index == 0 ? 3 : 4;
+ } else {
+ tmp = TO_TEMP_MODE[tmp];
+ }
+
+ return sprintf(buf, "%d\n", tmp);
+}
+
+static ssize_t
+store_temp_mode(struct device *dev, struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct w83793_data *data = i2c_get_clientdata(client);
+ struct sensor_device_attribute_2 *sensor_attr =
+ to_sensor_dev_attr_2(attr);
+ int index = sensor_attr->index;
+ u8 mask = (index < 4) ? 0x03 : 0x01;
+ u8 shift = (index < 4) ? (2 * index) : (index - 4);
+ u8 val = simple_strtoul(buf, NULL, 10);
+
+ /* transform the sysfs interface values into table above */
+ if ((val == 5 || val == 6) && (index < 4)) {
+ val -= 3;
+ } else if ((val == 3 && index < 4)
+ || (val == 4 && index >= 4)
+ || val == 0) {
+ /* transform diode or thermistor into internal enable */
+ val = !!val;
+ } else {
+ return -EINVAL;
+ }
+
+ index = (index < 4) ? 0 : 1;
+ mutex_lock(&data->update_lock);
+ data->temp_mode[index] =
+ w83793_read_value(client, W83793_REG_TEMP_MODE[index]);
+ data->temp_mode[index] &= ~(mask << shift);
+ data->temp_mode[index] |= val << shift;
+ w83793_write_value(client, W83793_REG_TEMP_MODE[index],
+ data->temp_mode[index]);
+ mutex_unlock(&data->update_lock);
+
+ return count;
+}
+
+#define SETUP_PWM_DEFAULT 0
+#define SETUP_PWM_UPTIME 1 /* Unit in 0.1s */
+#define SETUP_PWM_DOWNTIME 2 /* Unit in 0.1s */
+#define SETUP_TEMP_CRITICAL 3
+static ssize_t
+show_sf_setup(struct device *dev, struct device_attribute *attr, char *buf)
+{
+ struct sensor_device_attribute_2 *sensor_attr =
+ to_sensor_dev_attr_2(attr);
+ int nr = sensor_attr->nr;
+ struct w83793_data *data = w83793_update_device(dev);
+ u32 val = 0;
+
+ if (SETUP_PWM_DEFAULT == nr) {
+ val = (data->pwm_default & 0x3f) << 2;
+ } else if (SETUP_PWM_UPTIME == nr) {
+ val = TIME_FROM_REG(data->pwm_uptime);
+ } else if (SETUP_PWM_DOWNTIME == nr) {
+ val = TIME_FROM_REG(data->pwm_downtime);
+ } else if (SETUP_TEMP_CRITICAL == nr) {
+ val = TEMP_FROM_REG(data->temp_critical & 0x7f);
+ }
+
+ return sprintf(buf, "%d\n", val);
+}
+
+static ssize_t
+store_sf_setup(struct device *dev, struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct sensor_device_attribute_2 *sensor_attr =
+ to_sensor_dev_attr_2(attr);
+ int nr = sensor_attr->nr;
+ struct i2c_client *client = to_i2c_client(dev);
+ struct w83793_data *data = i2c_get_clientdata(client);
+
+ mutex_lock(&data->update_lock);
+ if (SETUP_PWM_DEFAULT == nr) {
+ data->pwm_default =
+ w83793_read_value(client, W83793_REG_PWM_DEFAULT) & 0xc0;
+ data->pwm_default |= SENSORS_LIMIT(simple_strtoul(buf, NULL,
+ 10),
+ 0, 0xff) >> 2;
+ w83793_write_value(client, W83793_REG_PWM_DEFAULT,
+ data->pwm_default);
+ } else if (SETUP_PWM_UPTIME == nr) {
+ data->pwm_uptime = TIME_TO_REG(simple_strtoul(buf, NULL, 10));
+ data->pwm_uptime += data->pwm_uptime == 0 ? 1 : 0;
+ w83793_write_value(client, W83793_REG_PWM_UPTIME,
+ data->pwm_uptime);
+ } else if (SETUP_PWM_DOWNTIME == nr) {
+ data->pwm_downtime = TIME_TO_REG(simple_strtoul(buf, NULL, 10));
+ data->pwm_downtime += data->pwm_downtime == 0 ? 1 : 0;
+ w83793_write_value(client, W83793_REG_PWM_DOWNTIME,
+ data->pwm_downtime);
+ } else { /* SETUP_TEMP_CRITICAL */
+ data->temp_critical =
+ w83793_read_value(client, W83793_REG_TEMP_CRITICAL) & 0x80;
+ data->temp_critical |= TEMP_TO_REG(simple_strtol(buf, NULL, 10),
+ 0, 0x7f);
+ w83793_write_value(client, W83793_REG_TEMP_CRITICAL,
+ data->temp_critical);
+ }
+
+ mutex_unlock(&data->update_lock);
+ return count;
+}
+
+/*
+ Temp SmartFan control
+ TEMP_FAN_MAP
+ Temp channel control which pwm fan, bitfield, bit 0 indicate pwm1...
+ It's possible two or more temp channels control the same fan, w83793
+ always prefers to pick the most critical request and applies it to
+ the related Fan.
+ It's possible one fan is not in any mapping of 6 temp channels, this
+ means the fan is manual mode
+
+ TEMP_PWM_ENABLE
+ Each temp channel has its own SmartFan mode, and temp channel
+ control fans that are set by TEMP_FAN_MAP
+ 0: SmartFanII mode
+ 1: Thermal Cruise Mode
+
+ TEMP_CRUISE
+ Target temperature in thermal cruise mode, w83793 will try to turn
+ fan speed to keep the temperature of target device around this
+ temperature.
+
+ TEMP_TOLERANCE
+ If Temp higher or lower than target with this tolerance, w83793
+ will take actions to speed up or slow down the fan to keep the
+ temperature within the tolerance range.
+*/
+
+#define TEMP_FAN_MAP 0
+#define TEMP_PWM_ENABLE 1
+#define TEMP_CRUISE 2
+#define TEMP_TOLERANCE 3
+static ssize_t
+show_sf_ctrl(struct device *dev, struct device_attribute *attr, char *buf)
+{
+ struct sensor_device_attribute_2 *sensor_attr =
+ to_sensor_dev_attr_2(attr);
+ int nr = sensor_attr->nr;
+ int index = sensor_attr->index;
+ struct w83793_data *data = w83793_update_device(dev);
+ u32 val;
+
+ if (TEMP_FAN_MAP == nr) {
+ val = data->temp_fan_map[index];
+ } else if (TEMP_PWM_ENABLE == nr) {
+ /* +2 to transfrom into 2 and 3 to conform with sysfs intf */
+ val = ((data->pwm_enable >> index) & 0x01) + 2;
+ } else if (TEMP_CRUISE == nr) {
+ val = TEMP_FROM_REG(data->temp_cruise[index] & 0x7f);
+ } else { /* TEMP_TOLERANCE */
+ val = data->tolerance[index >> 1] >> ((index & 0x01) ? 4 : 0);
+ val = TEMP_FROM_REG(val & 0x0f);
+ }
+ return sprintf(buf, "%d\n", val);
+}
+
+static ssize_t
+store_sf_ctrl(struct device *dev, struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct sensor_device_attribute_2 *sensor_attr =
+ to_sensor_dev_attr_2(attr);
+ int nr = sensor_attr->nr;
+ int index = sensor_attr->index;
+ struct i2c_client *client = to_i2c_client(dev);
+ struct w83793_data *data = i2c_get_clientdata(client);
+ u32 val;
+
+ mutex_lock(&data->update_lock);
+ if (TEMP_FAN_MAP == nr) {
+ val = simple_strtoul(buf, NULL, 10) & 0xff;
+ w83793_write_value(client, W83793_REG_TEMP_FAN_MAP(index), val);
+ data->temp_fan_map[index] = val;
+ } else if (TEMP_PWM_ENABLE == nr) {
+ val = simple_strtoul(buf, NULL, 10);
+ if (2 == val || 3 == val) {
+ data->pwm_enable =
+ w83793_read_value(client, W83793_REG_PWM_ENABLE);
+ if (val - 2)
+ data->pwm_enable |= 1 << index;
+ else
+ data->pwm_enable &= ~(1 << index);
+ w83793_write_value(client, W83793_REG_PWM_ENABLE,
+ data->pwm_enable);
+ } else {
+ mutex_unlock(&data->update_lock);
+ return -EINVAL;
+ }
+ } else if (TEMP_CRUISE == nr) {
+ data->temp_cruise[index] =
+ w83793_read_value(client, W83793_REG_TEMP_CRUISE(index));
+ val = TEMP_TO_REG(simple_strtol(buf, NULL, 10), 0, 0x7f);
+ data->temp_cruise[index] &= 0x80;
+ data->temp_cruise[index] |= val;
+
+ w83793_write_value(client, W83793_REG_TEMP_CRUISE(index),
+ data->temp_cruise[index]);
+ } else { /* TEMP_TOLERANCE */
+ int i = index >> 1;
+ u8 shift = (index & 0x01) ? 4 : 0;
+ data->tolerance[i] =
+ w83793_read_value(client, W83793_REG_TEMP_TOL(i));
+
+ val = TEMP_TO_REG(simple_strtol(buf, NULL, 10), 0, 0x0f);
+ data->tolerance[i] &= ~(0x0f << shift);
+ data->tolerance[i] |= val << shift;
+ w83793_write_value(client, W83793_REG_TEMP_TOL(i),
+ data->tolerance[i]);
+ }
+
+ mutex_unlock(&data->update_lock);
+ return count;
+}
+
+static ssize_t
+show_sf2_pwm(struct device *dev, struct device_attribute *attr, char *buf)
+{
+ struct sensor_device_attribute_2 *sensor_attr =
+ to_sensor_dev_attr_2(attr);
+ int nr = sensor_attr->nr;
+ int index = sensor_attr->index;
+ struct w83793_data *data = w83793_update_device(dev);
+
+ return sprintf(buf, "%d\n", (data->sf2_pwm[index][nr] & 0x3f) << 2);
+}
+
+static ssize_t
+store_sf2_pwm(struct device *dev, struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct w83793_data *data = i2c_get_clientdata(client);
+ struct sensor_device_attribute_2 *sensor_attr =
+ to_sensor_dev_attr_2(attr);
+ int nr = sensor_attr->nr;
+ int index = sensor_attr->index;
+ u8 val = SENSORS_LIMIT(simple_strtoul(buf, NULL, 10), 0, 0xff) >> 2;
+
+ mutex_lock(&data->update_lock);
+ data->sf2_pwm[index][nr] =
+ w83793_read_value(client, W83793_REG_SF2_PWM(index, nr)) & 0xc0;
+ data->sf2_pwm[index][nr] |= val;
+ w83793_write_value(client, W83793_REG_SF2_PWM(index, nr),
+ data->sf2_pwm[index][nr]);
+ mutex_unlock(&data->update_lock);
+ return count;
+}
+
+static ssize_t
+show_sf2_temp(struct device *dev, struct device_attribute *attr, char *buf)
+{
+ struct sensor_device_attribute_2 *sensor_attr =
+ to_sensor_dev_attr_2(attr);
+ int nr = sensor_attr->nr;
+ int index = sensor_attr->index;
+ struct w83793_data *data = w83793_update_device(dev);
+
+ return sprintf(buf, "%ld\n",
+ TEMP_FROM_REG(data->sf2_temp[index][nr] & 0x7f));
+}
+
+static ssize_t
+store_sf2_temp(struct device *dev, struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct w83793_data *data = i2c_get_clientdata(client);
+ struct sensor_device_attribute_2 *sensor_attr =
+ to_sensor_dev_attr_2(attr);
+ int nr = sensor_attr->nr;
+ int index = sensor_attr->index;
+ u8 val = TEMP_TO_REG(simple_strtol(buf, NULL, 10), 0, 0x7f);
+
+ mutex_lock(&data->update_lock);
+ data->sf2_temp[index][nr] =
+ w83793_read_value(client, W83793_REG_SF2_TEMP(index, nr)) & 0x80;
+ data->sf2_temp[index][nr] |= val;
+ w83793_write_value(client, W83793_REG_SF2_TEMP(index, nr),
+ data->sf2_temp[index][nr]);
+ mutex_unlock(&data->update_lock);
+ return count;
+}
+
+/* only Vcore A/B and Vtt have additional 2 bits precision */
+static ssize_t
+show_in(struct device *dev, struct device_attribute *attr, char *buf)
+{
+ struct sensor_device_attribute_2 *sensor_attr =
+ to_sensor_dev_attr_2(attr);
+ int nr = sensor_attr->nr;
+ int index = sensor_attr->index;
+ struct w83793_data *data = w83793_update_device(dev);
+ u16 val = data->in[index][nr];
+
+ if (index < 3) {
+ val <<= 2;
+ val += (data->in_low_bits[nr] >> (index * 2)) & 0x3;
+ }
+ return sprintf(buf, "%d\n", val * scale_in[index]);
+}
+
+static ssize_t
+store_in(struct device *dev, struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct sensor_device_attribute_2 *sensor_attr =
+ to_sensor_dev_attr_2(attr);
+ int nr = sensor_attr->nr;
+ int index = sensor_attr->index;
+ struct i2c_client *client = to_i2c_client(dev);
+ struct w83793_data *data = i2c_get_clientdata(client);
+ u32 val;
+
+ val =
+ (simple_strtoul(buf, NULL, 10) +
+ scale_in[index] / 2) / scale_in[index];
+ mutex_lock(&data->update_lock);
+ if (index > 2) {
+ val = SENSORS_LIMIT(val, 0, 255);
+ } else {
+ val = SENSORS_LIMIT(val, 0, 0x3FF);
+ data->in_low_bits[nr] =
+ w83793_read_value(client, W83793_REG_IN_LOW_BITS[nr]);
+ data->in_low_bits[nr] &= ~(0x03 << (2 * index));
+ data->in_low_bits[nr] |= (val & 0x03) << (2 * index);
+ w83793_write_value(client, W83793_REG_IN_LOW_BITS[nr],
+ data->in_low_bits[nr]);
+ val >>= 2;
+ }
+ data->in[index][nr] = val;
+ w83793_write_value(client, W83793_REG_IN[index][nr],
+ data->in[index][nr]);
+ mutex_unlock(&data->update_lock);
+ return count;
+}
+
+#define NOT_USED -1
+
+#define SENSOR_ATTR_IN(index) \
+ SENSOR_ATTR_2(in##index##_input, S_IRUGO, show_in, NULL, \
+ IN_READ, index), \
+ SENSOR_ATTR_2(in##index##_max, S_IRUGO | S_IWUSR, show_in, \
+ store_in, IN_MAX, index), \
+ SENSOR_ATTR_2(in##index##_min, S_IRUGO | S_IWUSR, show_in, \
+ store_in, IN_LOW, index), \
+ SENSOR_ATTR_2(in##index##_alarm, S_IRUGO, show_alarm_beep, \
+ NULL, ALARM_STATUS, index + ((index > 2) ? 1 : 0)), \
+ SENSOR_ATTR_2(in##index##_beep, S_IWUSR | S_IRUGO, \
+ show_alarm_beep, store_beep, BEEP_ENABLE, \
+ index + ((index > 2) ? 1 : 0))
+
+#define SENSOR_ATTR_FAN(index) \
+ SENSOR_ATTR_2(fan##index##_alarm, S_IRUGO, show_alarm_beep, \
+ NULL, ALARM_STATUS, index + 17), \
+ SENSOR_ATTR_2(fan##index##_beep, S_IWUSR | S_IRUGO, \
+ show_alarm_beep, store_beep, BEEP_ENABLE, index + 17), \
+ SENSOR_ATTR_2(fan##index##_input, S_IRUGO, show_fan, \
+ NULL, FAN_INPUT, index - 1), \
+ SENSOR_ATTR_2(fan##index##_min, S_IWUSR | S_IRUGO, \
+ show_fan, store_fan_min, FAN_MIN, index - 1)
+
+#define SENSOR_ATTR_PWM(index) \
+ SENSOR_ATTR_2(pwm##index, S_IWUSR | S_IRUGO, show_pwm, \
+ store_pwm, PWM_DUTY, index - 1), \
+ SENSOR_ATTR_2(pwm##index##_nonstop, S_IWUSR | S_IRUGO, \
+ show_pwm, store_pwm, PWM_NONSTOP, index - 1), \
+ SENSOR_ATTR_2(pwm##index##_start, S_IWUSR | S_IRUGO, \
+ show_pwm, store_pwm, PWM_START, index - 1), \
+ SENSOR_ATTR_2(pwm##index##_stop_time, S_IWUSR | S_IRUGO, \
+ show_pwm, store_pwm, PWM_STOP_TIME, index - 1)
+
+#define SENSOR_ATTR_TEMP(index) \
+ SENSOR_ATTR_2(temp##index##_type, S_IRUGO | S_IWUSR, \
+ show_temp_mode, store_temp_mode, NOT_USED, index - 1), \
+ SENSOR_ATTR_2(temp##index##_input, S_IRUGO, show_temp, \
+ NULL, TEMP_READ, index - 1), \
+ SENSOR_ATTR_2(temp##index##_max, S_IRUGO | S_IWUSR, show_temp, \
+ store_temp, TEMP_CRIT, index - 1), \
+ SENSOR_ATTR_2(temp##index##_max_hyst, S_IRUGO | S_IWUSR, \
+ show_temp, store_temp, TEMP_CRIT_HYST, index - 1), \
+ SENSOR_ATTR_2(temp##index##_warn, S_IRUGO | S_IWUSR, show_temp, \
+ store_temp, TEMP_WARN, index - 1), \
+ SENSOR_ATTR_2(temp##index##_warn_hyst, S_IRUGO | S_IWUSR, \
+ show_temp, store_temp, TEMP_WARN_HYST, index - 1), \
+ SENSOR_ATTR_2(temp##index##_alarm, S_IRUGO, \
+ show_alarm_beep, NULL, ALARM_STATUS, index + 11), \
+ SENSOR_ATTR_2(temp##index##_beep, S_IWUSR | S_IRUGO, \
+ show_alarm_beep, store_beep, BEEP_ENABLE, index + 11), \
+ SENSOR_ATTR_2(temp##index##_auto_channels_pwm, \
+ S_IRUGO | S_IWUSR, show_sf_ctrl, store_sf_ctrl, \
+ TEMP_FAN_MAP, index - 1), \
+ SENSOR_ATTR_2(temp##index##_pwm_enable, S_IWUSR | S_IRUGO, \
+ show_sf_ctrl, store_sf_ctrl, TEMP_PWM_ENABLE, \
+ index - 1), \
+ SENSOR_ATTR_2(thermal_cruise##index, S_IRUGO | S_IWUSR, \
+ show_sf_ctrl, store_sf_ctrl, TEMP_CRUISE, index - 1), \
+ SENSOR_ATTR_2(tolerance##index, S_IRUGO | S_IWUSR, show_sf_ctrl,\
+ store_sf_ctrl, TEMP_TOLERANCE, index - 1), \
+ SENSOR_ATTR_2(temp##index##_auto_point1_pwm, S_IRUGO | S_IWUSR, \
+ show_sf2_pwm, store_sf2_pwm, 0, index - 1), \
+ SENSOR_ATTR_2(temp##index##_auto_point2_pwm, S_IRUGO | S_IWUSR, \
+ show_sf2_pwm, store_sf2_pwm, 1, index - 1), \
+ SENSOR_ATTR_2(temp##index##_auto_point3_pwm, S_IRUGO | S_IWUSR, \
+ show_sf2_pwm, store_sf2_pwm, 2, index - 1), \
+ SENSOR_ATTR_2(temp##index##_auto_point4_pwm, S_IRUGO | S_IWUSR, \
+ show_sf2_pwm, store_sf2_pwm, 3, index - 1), \
+ SENSOR_ATTR_2(temp##index##_auto_point5_pwm, S_IRUGO | S_IWUSR, \
+ show_sf2_pwm, store_sf2_pwm, 4, index - 1), \
+ SENSOR_ATTR_2(temp##index##_auto_point6_pwm, S_IRUGO | S_IWUSR, \
+ show_sf2_pwm, store_sf2_pwm, 5, index - 1), \
+ SENSOR_ATTR_2(temp##index##_auto_point7_pwm, S_IRUGO | S_IWUSR, \
+ show_sf2_pwm, store_sf2_pwm, 6, index - 1), \
+ SENSOR_ATTR_2(temp##index##_auto_point1_temp, S_IRUGO | S_IWUSR,\
+ show_sf2_temp, store_sf2_temp, 0, index - 1), \
+ SENSOR_ATTR_2(temp##index##_auto_point2_temp, S_IRUGO | S_IWUSR,\
+ show_sf2_temp, store_sf2_temp, 1, index - 1), \
+ SENSOR_ATTR_2(temp##index##_auto_point3_temp, S_IRUGO | S_IWUSR,\
+ show_sf2_temp, store_sf2_temp, 2, index - 1), \
+ SENSOR_ATTR_2(temp##index##_auto_point4_temp, S_IRUGO | S_IWUSR,\
+ show_sf2_temp, store_sf2_temp, 3, index - 1), \
+ SENSOR_ATTR_2(temp##index##_auto_point5_temp, S_IRUGO | S_IWUSR,\
+ show_sf2_temp, store_sf2_temp, 4, index - 1), \
+ SENSOR_ATTR_2(temp##index##_auto_point6_temp, S_IRUGO | S_IWUSR,\
+ show_sf2_temp, store_sf2_temp, 5, index - 1), \
+ SENSOR_ATTR_2(temp##index##_auto_point7_temp, S_IRUGO | S_IWUSR,\
+ show_sf2_temp, store_sf2_temp, 6, index - 1)
+
+static struct sensor_device_attribute_2 w83793_sensor_attr_2[] = {
+ SENSOR_ATTR_IN(0),
+ SENSOR_ATTR_IN(1),
+ SENSOR_ATTR_IN(2),
+ SENSOR_ATTR_IN(3),
+ SENSOR_ATTR_IN(4),
+ SENSOR_ATTR_IN(5),
+ SENSOR_ATTR_IN(6),
+ SENSOR_ATTR_IN(7),
+ SENSOR_ATTR_IN(8),
+ SENSOR_ATTR_IN(9),
+ SENSOR_ATTR_TEMP(1),
+ SENSOR_ATTR_TEMP(2),
+ SENSOR_ATTR_TEMP(3),
+ SENSOR_ATTR_TEMP(4),
+ SENSOR_ATTR_TEMP(5),
+ SENSOR_ATTR_TEMP(6),
+ SENSOR_ATTR_FAN(1),
+ SENSOR_ATTR_FAN(2),
+ SENSOR_ATTR_FAN(3),
+ SENSOR_ATTR_FAN(4),
+ SENSOR_ATTR_FAN(5),
+ SENSOR_ATTR_PWM(1),
+ SENSOR_ATTR_PWM(2),
+ SENSOR_ATTR_PWM(3),
+};
+
+/* Fan6-Fan12 */
+static struct sensor_device_attribute_2 w83793_left_fan[] = {
+ SENSOR_ATTR_FAN(6),
+ SENSOR_ATTR_FAN(7),
+ SENSOR_ATTR_FAN(8),
+ SENSOR_ATTR_FAN(9),
+ SENSOR_ATTR_FAN(10),
+ SENSOR_ATTR_FAN(11),
+ SENSOR_ATTR_FAN(12),
+};
+
+/* Pwm4-Pwm8 */
+static struct sensor_device_attribute_2 w83793_left_pwm[] = {
+ SENSOR_ATTR_PWM(4),
+ SENSOR_ATTR_PWM(5),
+ SENSOR_ATTR_PWM(6),
+ SENSOR_ATTR_PWM(7),
+ SENSOR_ATTR_PWM(8),
+};
+
+static struct sensor_device_attribute_2 sda_single_files[] = {
+ SENSOR_ATTR_2(cpu0_vid, S_IRUGO, show_vid, NULL, NOT_USED, 0),
+ SENSOR_ATTR_2(cpu1_vid, S_IRUGO, show_vid, NULL, NOT_USED, 1),
+ SENSOR_ATTR_2(vrm, S_IWUSR | S_IRUGO, show_vrm, store_vrm,
+ NOT_USED, NOT_USED),
+ SENSOR_ATTR_2(chassis, S_IWUSR | S_IRUGO, show_alarm_beep,
+ store_chassis_clear, ALARM_STATUS, 30),
+ SENSOR_ATTR_2(beep_enable, S_IWUSR | S_IRUGO, show_beep_enable,
+ store_beep_enable, NOT_USED, NOT_USED),
+ SENSOR_ATTR_2(pwm_default, S_IWUSR | S_IRUGO, show_sf_setup,
+ store_sf_setup, SETUP_PWM_DEFAULT, NOT_USED),
+ SENSOR_ATTR_2(pwm_uptime, S_IWUSR | S_IRUGO, show_sf_setup,
+ store_sf_setup, SETUP_PWM_UPTIME, NOT_USED),
+ SENSOR_ATTR_2(pwm_downtime, S_IWUSR | S_IRUGO, show_sf_setup,
+ store_sf_setup, SETUP_PWM_DOWNTIME, NOT_USED),
+ SENSOR_ATTR_2(temp_critical, S_IWUSR | S_IRUGO, show_sf_setup,
+ store_sf_setup, SETUP_TEMP_CRITICAL, NOT_USED),
+};
+
+static void w83793_init_client(struct i2c_client *client)
+{
+ if (reset) {
+ w83793_write_value(client, W83793_REG_CONFIG, 0x80);
+ }
+
+ /* Start monitoring */
+ w83793_write_value(client, W83793_REG_CONFIG,
+ w83793_read_value(client, W83793_REG_CONFIG) | 0x01);
+
+}
+
+static int w83793_attach_adapter(struct i2c_adapter *adapter)
+{
+ if (!(adapter->class & I2C_CLASS_HWMON))
+ return 0;
+ return i2c_probe(adapter, &addr_data, w83793_detect);
+}
+
+static int w83793_detach_client(struct i2c_client *client)
+{
+ struct w83793_data *data = i2c_get_clientdata(client);
+ struct device *dev = &client->dev;
+ int err, i;
+
+ /* main client */
+ if (data) {
+ hwmon_device_unregister(data->class_dev);
+
+ for (i = 0; i < ARRAY_SIZE(w83793_sensor_attr_2); i++)
+ device_remove_file(dev,
+ &w83793_sensor_attr_2[i].dev_attr);
+
+ for (i = 0; i < ARRAY_SIZE(sda_single_files); i++)
+ device_remove_file(dev, &sda_single_files[i].dev_attr);
+
+ for (i = 0; i < ARRAY_SIZE(w83793_left_fan); i++)
+ device_remove_file(dev, &w83793_left_fan[i].dev_attr);
+
+ for (i = 0; i < ARRAY_SIZE(w83793_left_pwm); i++)
+ device_remove_file(dev, &w83793_left_pwm[i].dev_attr);
+ }
+
+ if ((err = i2c_detach_client(client)))
+ return err;
+
+ /* main client */
+ if (data)
+ kfree(data);
+ /* subclient */
+ else
+ kfree(client);
+
+ return 0;
+}
+
+static int
+w83793_create_subclient(struct i2c_adapter *adapter,
+ struct i2c_client *client, int addr,
+ struct i2c_client **sub_cli)
+{
+ int err = 0;
+ struct i2c_client *sub_client;
+
+ (*sub_cli) = sub_client =
+ kzalloc(sizeof(struct i2c_client), GFP_KERNEL);
+ if (!(sub_client)) {
+ return -ENOMEM;
+ }
+ sub_client->addr = 0x48 + addr;
+ i2c_set_clientdata(sub_client, NULL);
+ sub_client->adapter = adapter;
+ sub_client->driver = &w83793_driver;
+ strlcpy(sub_client->name, "w83793 subclient", I2C_NAME_SIZE);
+ if ((err = i2c_attach_client(sub_client))) {
+ dev_err(&client->dev, "subclient registration "
+ "at address 0x%x failed\n", sub_client->addr);
+ kfree(sub_client);
+ }
+ return err;
+}
+
+static int
+w83793_detect_subclients(struct i2c_adapter *adapter, int address,
+ int kind, struct i2c_client *client)
+{
+ int i, id, err;
+ u8 tmp;
+ struct w83793_data *data = i2c_get_clientdata(client);
+
+ id = i2c_adapter_id(adapter);
+ if (force_subclients[0] == id && force_subclients[1] == address) {
+ for (i = 2; i <= 3; i++) {
+ if (force_subclients[i] < 0x48
+ || force_subclients[i] > 0x4f) {
+ dev_err(&client->dev,
+ "invalid subclient "
+ "address %d; must be 0x48-0x4f\n",
+ force_subclients[i]);
+ err = -EINVAL;
+ goto ERROR_SC_0;
+ }
+ }
+ w83793_write_value(client, W83793_REG_I2C_SUBADDR,
+ (force_subclients[2] & 0x07) |
+ ((force_subclients[3] & 0x07) << 4));
+ }
+
+ tmp = w83793_read_value(client, W83793_REG_I2C_SUBADDR);
+ if (!(tmp & 0x08)) {
+ err =
+ w83793_create_subclient(adapter, client, tmp & 0x7,
+ &data->lm75[0]);
+ if (err < 0)
+ goto ERROR_SC_0;
+ }
+ if (!(tmp & 0x80)) {
+ if ((data->lm75[0] != NULL)
+ && ((tmp & 0x7) == ((tmp >> 4) & 0x7))) {
+ dev_err(&client->dev,
+ "duplicate addresses 0x%x, "
+ "use force_subclients\n", data->lm75[0]->addr);
+ err = -ENODEV;
+ goto ERROR_SC_1;
+ }
+ err = w83793_create_subclient(adapter, client,
+ (tmp >> 4) & 0x7, &data->lm75[1]);
+ if (err < 0)
+ goto ERROR_SC_1;
+ }
+
+ return 0;
+
+ /* Undo inits in case of errors */
+
+ERROR_SC_1:
+ if (data->lm75[0] != NULL) {
+ i2c_detach_client(data->lm75[0]);
+ kfree(data->lm75[0]);
+ }
+ERROR_SC_0:
+ return err;
+}
+
+static int w83793_detect(struct i2c_adapter *adapter, int address, int kind)
+{
+ int i;
+ u8 tmp, val;
+ struct i2c_client *client;
+ struct device *dev;
+ struct w83793_data *data;
+ int files_fan = ARRAY_SIZE(w83793_left_fan) / 7;
+ int files_pwm = ARRAY_SIZE(w83793_left_pwm) / 5;
+ int err = 0;
+
+ if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) {
+ goto exit;
+ }
+
+ /* OK. For now, we presume we have a valid client. We now create the
+ client structure, even though we cannot fill it completely yet.
+ But it allows us to access w83793_{read,write}_value. */
+
+ if (!(data = kzalloc(sizeof(struct w83793_data), GFP_KERNEL))) {
+ err = -ENOMEM;
+ goto exit;
+ }
+
+ client = &data->client;
+ dev = &client->dev;
+ i2c_set_clientdata(client, data);
+ client->addr = address;
+ client->adapter = adapter;
+ client->driver = &w83793_driver;
+
+ data->bank = i2c_smbus_read_byte_data(client, W83793_REG_BANKSEL);
+
+ /* Now, we do the remaining detection. */
+ if (kind < 0) {
+ tmp = data->bank & 0x80 ? 0x5c : 0xa3;
+ /* Check Winbond vendor ID */
+ if (tmp != i2c_smbus_read_byte_data(client,
+ W83793_REG_VENDORID)) {
+ pr_debug("w83793: Detection failed at check "
+ "vendor id\n");
+ err = -ENODEV;
+ goto free_mem;
+ }
+
+ /* If Winbond chip, address of chip and W83793_REG_I2C_ADDR
+ should match */
+ if ((data->bank & 0x07) == 0
+ && i2c_smbus_read_byte_data(client, W83793_REG_I2C_ADDR) !=
+ (address << 1)) {
+ pr_debug("w83793: Detection failed at check "
+ "i2c addr\n");
+ err = -ENODEV;
+ goto free_mem;
+ }
+
+ }
+
+ /* We have either had a force parameter, or we have already detected the
+ Winbond. Determine the chip type now */
+
+ if (kind <= 0) {
+ if (0x7b == w83793_read_value(client, W83793_REG_CHIPID)) {
+ kind = w83793;
+ } else {
+ if (kind == 0)
+ dev_warn(&adapter->dev, "w83793: Ignoring "
+ "'force' parameter for unknown chip "
+ "at address 0x%02x\n", address);
+ err = -ENODEV;
+ goto free_mem;
+ }
+ }
+
+ /* Fill in the remaining client fields and put into the global list */
+ strlcpy(client->name, "w83793", I2C_NAME_SIZE);
+
+ mutex_init(&data->update_lock);
+
+ /* Tell the I2C layer a new client has arrived */
+ if ((err = i2c_attach_client(client)))
+ goto free_mem;
+
+ if ((err = w83793_detect_subclients(adapter, address, kind, client)))
+ goto detach_client;
+
+ /* Initialize the chip */
+ w83793_init_client(client);
+
+ data->vrm = vid_which_vrm();
+ /*
+ Only fan 1-5 has their own input pins,
+ Pwm 1-3 has their own pins
+ */
+ data->has_fan = 0x1f;
+ data->has_pwm = 0x07;
+ tmp = w83793_read_value(client, W83793_REG_MFC);
+ val = w83793_read_value(client, W83793_REG_FANIN_CTRL);
+
+ /* check the function of pins 49-56 */
+ if (!(tmp & 0x80)) {
+ data->has_pwm |= 0x18; /* pwm 4,5 */
+ if (val & 0x01) { /* fan 6 */
+ data->has_fan |= 0x20;
+ data->has_pwm |= 0x20;
+ }
+ if (val & 0x02) { /* fan 7 */
+ data->has_fan |= 0x40;
+ data->has_pwm |= 0x40;
+ }
+ if (!(tmp & 0x40) && (val & 0x04)) { /* fan 8 */
+ data->has_fan |= 0x80;
+ data->has_pwm |= 0x80;
+ }
+ }
+
+ if (0x08 == (tmp & 0x0c)) {
+ if (val & 0x08) /* fan 9 */
+ data->has_fan |= 0x100;
+ if (val & 0x10) /* fan 10 */
+ data->has_fan |= 0x200;
+ }
+
+ if (0x20 == (tmp & 0x30)) {
+ if (val & 0x20) /* fan 11 */
+ data->has_fan |= 0x400;
+ if (val & 0x40) /* fan 12 */
+ data->has_fan |= 0x800;
+ }
+
+ if ((tmp & 0x01) && (val & 0x04)) { /* fan 8, second location */
+ data->has_fan |= 0x80;
+ data->has_pwm |= 0x80;
+ }
+
+ /* Register sysfs hooks */
+ for (i = 0; i < ARRAY_SIZE(w83793_sensor_attr_2); i++) {
+ err = device_create_file(dev,
+ &w83793_sensor_attr_2[i].dev_attr);
+ if (err)
+ goto exit_remove;
+ }
+
+ for (i = 0; i < ARRAY_SIZE(sda_single_files); i++) {
+ err = device_create_file(dev, &sda_single_files[i].dev_attr);
+ if (err)
+ goto exit_remove;
+
+ }
+
+ for (i = 5; i < 12; i++) {
+ int j;
+ if (!(data->has_fan & (1 << i)))
+ continue;
+ for (j = 0; j < files_fan; j++) {
+ err = device_create_file(dev,
+ &w83793_left_fan[(i - 5) * files_fan
+ + j].dev_attr);
+ if (err)
+ goto exit_remove;
+ }
+ }
+
+ for (i = 3; i < 8; i++) {
+ int j;
+ if (!(data->has_pwm & (1 << i)))
+ continue;
+ for (j = 0; j < files_pwm; j++) {
+ err = device_create_file(dev,
+ &w83793_left_pwm[(i - 3) * files_pwm
+ + j].dev_attr);
+ if (err)
+ goto exit_remove;
+ }
+ }
+
+ data->class_dev = hwmon_device_register(dev);
+ if (IS_ERR(data->class_dev)) {
+ err = PTR_ERR(data->class_dev);
+ goto exit_remove;
+ }
+
+ return 0;
+
+ /* Unregister sysfs hooks */
+
+exit_remove:
+ for (i = 0; i < ARRAY_SIZE(w83793_sensor_attr_2); i++)
+ device_remove_file(dev, &w83793_sensor_attr_2[i].dev_attr);
+
+ for (i = 0; i < ARRAY_SIZE(sda_single_files); i++)
+ device_remove_file(dev, &sda_single_files[i].dev_attr);
+
+ for (i = 0; i < ARRAY_SIZE(w83793_left_fan); i++)
+ device_remove_file(dev, &w83793_left_fan[i].dev_attr);
+
+ for (i = 0; i < ARRAY_SIZE(w83793_left_pwm); i++)
+ device_remove_file(dev, &w83793_left_pwm[i].dev_attr);
+
+ if (data->lm75[0] != NULL) {
+ i2c_detach_client(data->lm75[0]);
+ kfree(data->lm75[0]);
+ }
+ if (data->lm75[1] != NULL) {
+ i2c_detach_client(data->lm75[1]);
+ kfree(data->lm75[1]);
+ }
+detach_client:
+ i2c_detach_client(client);
+free_mem:
+ kfree(data);
+exit:
+ return err;
+}
+
+static void w83793_update_nonvolatile(struct device *dev)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct w83793_data *data = i2c_get_clientdata(client);
+ int i, j;
+ /*
+ They are somewhat "stable" registers, and to update them everytime
+ takes so much time, it's just not worthy. Update them in a long
+ interval to avoid exception.
+ */
+ if (!(time_after(jiffies, data->last_nonvolatile + HZ * 300)
+ || !data->valid))
+ return;
+ /* update voltage limits */
+ for (i = 1; i < 3; i++) {
+ for (j = 0; j < ARRAY_SIZE(data->in); j++) {
+ data->in[j][i] =
+ w83793_read_value(client, W83793_REG_IN[j][i]);
+ }
+ data->in_low_bits[i] =
+ w83793_read_value(client, W83793_REG_IN_LOW_BITS[i]);
+ }
+
+ for (i = 0; i < ARRAY_SIZE(data->fan_min); i++) {
+ /* Update the Fan measured value and limits */
+ if (!(data->has_fan & (1 << i))) {
+ continue;
+ }
+ data->fan_min[i] =
+ w83793_read_value(client, W83793_REG_FAN_MIN(i)) << 8;
+ data->fan_min[i] |=
+ w83793_read_value(client, W83793_REG_FAN_MIN(i) + 1);
+ }
+
+ for (i = 0; i < ARRAY_SIZE(data->temp_fan_map); i++) {
+ data->temp_fan_map[i] =
+ w83793_read_value(client, W83793_REG_TEMP_FAN_MAP(i));
+ for (j = 1; j < 5; j++) {
+ data->temp[i][j] =
+ w83793_read_value(client, W83793_REG_TEMP[i][j]);
+ }
+ data->temp_cruise[i] =
+ w83793_read_value(client, W83793_REG_TEMP_CRUISE(i));
+ for (j = 0; j < 7; j++) {
+ data->sf2_pwm[i][j] =
+ w83793_read_value(client, W83793_REG_SF2_PWM(i, j));
+ data->sf2_temp[i][j] =
+ w83793_read_value(client,
+ W83793_REG_SF2_TEMP(i, j));
+ }
+ }
+
+ for (i = 0; i < ARRAY_SIZE(data->temp_mode); i++)
+ data->temp_mode[i] =
+ w83793_read_value(client, W83793_REG_TEMP_MODE[i]);
+
+ for (i = 0; i < ARRAY_SIZE(data->tolerance); i++) {
+ data->tolerance[i] =
+ w83793_read_value(client, W83793_REG_TEMP_TOL(i));
+ }
+
+ for (i = 0; i < ARRAY_SIZE(data->pwm); i++) {
+ if (!(data->has_pwm & (1 << i)))
+ continue;
+ data->pwm[i][PWM_NONSTOP] =
+ w83793_read_value(client, W83793_REG_PWM(i, PWM_NONSTOP));
+ data->pwm[i][PWM_START] =
+ w83793_read_value(client, W83793_REG_PWM(i, PWM_START));
+ data->pwm_stop_time[i] =
+ w83793_read_value(client, W83793_REG_PWM_STOP_TIME(i));
+ }
+
+ data->pwm_default = w83793_read_value(client, W83793_REG_PWM_DEFAULT);
+ data->pwm_enable = w83793_read_value(client, W83793_REG_PWM_ENABLE);
+ data->pwm_uptime = w83793_read_value(client, W83793_REG_PWM_UPTIME);
+ data->pwm_downtime = w83793_read_value(client, W83793_REG_PWM_DOWNTIME);
+ data->temp_critical =
+ w83793_read_value(client, W83793_REG_TEMP_CRITICAL);
+ data->beep_enable = w83793_read_value(client, W83793_REG_OVT_BEEP);
+
+ for (i = 0; i < ARRAY_SIZE(data->beeps); i++) {
+ data->beeps[i] = w83793_read_value(client, W83793_REG_BEEP(i));
+ }
+
+ data->last_nonvolatile = jiffies;
+}
+
+static struct w83793_data *w83793_update_device(struct device *dev)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct w83793_data *data = i2c_get_clientdata(client);
+ int i;
+
+ mutex_lock(&data->update_lock);
+
+ if (!(time_after(jiffies, data->last_updated + HZ * 2)
+ || !data->valid))
+ goto END;
+
+ /* Update the voltages measured value and limits */
+ for (i = 0; i < ARRAY_SIZE(data->in); i++)
+ data->in[i][IN_READ] =
+ w83793_read_value(client, W83793_REG_IN[i][IN_READ]);
+
+ data->in_low_bits[IN_READ] =
+ w83793_read_value(client, W83793_REG_IN_LOW_BITS[IN_READ]);
+
+ for (i = 0; i < ARRAY_SIZE(data->fan); i++) {
+ if (!(data->has_fan & (1 << i))) {
+ continue;
+ }
+ data->fan[i] =
+ w83793_read_value(client, W83793_REG_FAN(i)) << 8;
+ data->fan[i] |=
+ w83793_read_value(client, W83793_REG_FAN(i) + 1);
+ }
+
+ for (i = 0; i < ARRAY_SIZE(data->temp); i++)
+ data->temp[i][TEMP_READ] =
+ w83793_read_value(client, W83793_REG_TEMP[i][TEMP_READ]);
+
+ data->temp_low_bits =
+ w83793_read_value(client, W83793_REG_TEMP_LOW_BITS);
+
+ for (i = 0; i < ARRAY_SIZE(data->pwm); i++) {
+ if (data->has_pwm & (1 << i))
+ data->pwm[i][PWM_DUTY] =
+ w83793_read_value(client,
+ W83793_REG_PWM(i, PWM_DUTY));
+ }
+
+ for (i = 0; i < ARRAY_SIZE(data->alarms); i++)
+ data->alarms[i] =
+ w83793_read_value(client, W83793_REG_ALARM(i));
+ data->vid[0] = w83793_read_value(client, W83793_REG_VID_INA);
+ data->vid[1] = w83793_read_value(client, W83793_REG_VID_INB);
+ w83793_update_nonvolatile(dev);
+ data->last_updated = jiffies;
+ data->valid = 1;
+
+END:
+ mutex_unlock(&data->update_lock);
+ return data;
+}
+
+/* Ignore the possibility that somebody change bank outside the driver
+ Must be called with data->update_lock held, except during initialization */
+static u8 w83793_read_value(struct i2c_client *client, u16 reg)
+{
+ struct w83793_data *data = i2c_get_clientdata(client);
+ u8 res = 0xff;
+ u8 new_bank = reg >> 8;
+
+ new_bank |= data->bank & 0xfc;
+ if (data->bank != new_bank) {
+ if (i2c_smbus_write_byte_data
+ (client, W83793_REG_BANKSEL, new_bank) >= 0)
+ data->bank = new_bank;
+ else {
+ dev_err(&client->dev,
+ "set bank to %d failed, fall back "
+ "to bank %d, read reg 0x%x error\n",
+ new_bank, data->bank, reg);
+ res = 0x0; /* read 0x0 from the chip */
+ goto END;
+ }
+ }
+ res = i2c_smbus_read_byte_data(client, reg & 0xff);
+END:
+ return res;
+}
+
+/* Must be called with data->update_lock held, except during initialization */
+static int w83793_write_value(struct i2c_client *client, u16 reg, u8 value)
+{
+ struct w83793_data *data = i2c_get_clientdata(client);
+ int res;
+ u8 new_bank = reg >> 8;
+
+ new_bank |= data->bank & 0xfc;
+ if (data->bank != new_bank) {
+ if ((res = i2c_smbus_write_byte_data
+ (client, W83793_REG_BANKSEL, new_bank)) >= 0)
+ data->bank = new_bank;
+ else {
+ dev_err(&client->dev,
+ "set bank to %d failed, fall back "
+ "to bank %d, write reg 0x%x error\n",
+ new_bank, data->bank, reg);
+ goto END;
+ }
+ }
+
+ res = i2c_smbus_write_byte_data(client, reg & 0xff, value);
+END:
+ return res;
+}
+
+static int __init sensors_w83793_init(void)
+{
+ return i2c_add_driver(&w83793_driver);
+}
+
+static void __exit sensors_w83793_exit(void)
+{
+ i2c_del_driver(&w83793_driver);
+}
+
+MODULE_AUTHOR("Yuan Mu");
+MODULE_DESCRIPTION("w83793 driver");
+MODULE_LICENSE("GPL");
+
+module_init(sensors_w83793_init);
+module_exit(sensors_w83793_exit);
projects / linux-2.6 / commitdiff