+++ /dev/null
-if ARCH_OMAP
-
-menu "TI OMAP Implementations"
-
-config ARCH_OMAP_OTG
- bool
-
-choice
- prompt "OMAP System Type"
- default ARCH_OMAP1
-
-config ARCH_OMAP1
- bool "TI OMAP1"
-
-config ARCH_OMAP2
- bool "TI OMAP2"
-
-endchoice
-
-comment "OMAP Feature Selections"
-
-config OMAP_MUX
- bool "OMAP multiplexing support"
- depends on ARCH_OMAP
- default y
- help
- Pin multiplexing support for OMAP boards. If your bootloader
- sets the multiplexing correctly, say N. Otherwise, or if unsure,
- say Y.
-
-config OMAP_MUX_DEBUG
- bool "Multiplexing debug output"
- depends on OMAP_MUX
- default n
- help
- Makes the multiplexing functions print out a lot of debug info.
- This is useful if you want to find out the correct values of the
- multiplexing registers.
-
-config OMAP_MUX_WARNINGS
- bool "Warn about pins the bootloader didn't set up"
- depends on OMAP_MUX
- default y
- help
- Choose Y here to warn whenever driver initialization logic needs
- to change the pin multiplexing setup. When there are no warnings
- printed, it's safe to deselect OMAP_MUX for your product.
-
-choice
- prompt "System timer"
- default OMAP_MPU_TIMER
-
-config OMAP_MPU_TIMER
- bool "Use mpu timer"
- help
- Select this option if you want to use the OMAP mpu timer. This
- timer provides more intra-tick resolution than the 32KHz timer,
- but consumes more power.
-
-config OMAP_32K_TIMER
- bool "Use 32KHz timer"
- depends on ARCH_OMAP16XX
- help
- Select this option if you want to enable the OMAP 32KHz timer.
- This timer saves power compared to the OMAP_MPU_TIMER, and has
- support for no tick during idle. The 32KHz timer provides less
- intra-tick resolution than OMAP_MPU_TIMER. The 32KHz timer is
- currently only available for OMAP-16xx.
-
-endchoice
-
-config OMAP_32K_TIMER_HZ
- int "Kernel internal timer frequency for 32KHz timer"
- range 32 1024
- depends on OMAP_32K_TIMER
- default "128"
- help
- Kernel internal timer frequency should be a divisor of 32768,
- such as 64 or 128.
-
-choice
- prompt "Low-level debug console UART"
- depends on ARCH_OMAP
- default OMAP_LL_DEBUG_UART1
-
-config OMAP_LL_DEBUG_UART1
- bool "UART1"
-
-config OMAP_LL_DEBUG_UART2
- bool "UART2"
-
-config OMAP_LL_DEBUG_UART3
- bool "UART3"
-
-endchoice
-
-endmenu
-
-endif
+++ /dev/null
-#
-# Makefile for the linux kernel.
-#
-
-# Common support
-obj-y := common.o dma.o clock.o mux.o gpio.o mcbsp.o usb.o
-obj-m :=
-obj-n :=
-obj- :=
-
-# OCPI interconnect support for 1710, 1610 and 5912
-obj-$(CONFIG_ARCH_OMAP16XX) += ocpi.o
-
-# Power Management
-obj-$(CONFIG_PM) += pm.o sleep.o
-
+++ /dev/null
-/*
- * linux/arch/arm/mach-omap/common.c
- *
- * Code common to all OMAP machines.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-#include <linux/config.h>
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/delay.h>
-#include <linux/pm.h>
-#include <linux/console.h>
-#include <linux/serial.h>
-#include <linux/tty.h>
-#include <linux/serial_8250.h>
-#include <linux/serial_reg.h>
-
-#include <asm/hardware.h>
-#include <asm/system.h>
-#include <asm/pgtable.h>
-#include <asm/mach/map.h>
-#include <asm/hardware/clock.h>
-#include <asm/io.h>
-#include <asm/mach-types.h>
-
-#include <asm/arch/board.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/fpga.h>
-
-#include "clock.h"
-
-#define NO_LENGTH_CHECK 0xffffffff
-
-extern int omap_bootloader_tag_len;
-extern u8 omap_bootloader_tag[];
-
-struct omap_board_config_kernel *omap_board_config;
-int omap_board_config_size = 0;
-
-static const void *get_config(u16 tag, size_t len, int skip, size_t *len_out)
-{
- struct omap_board_config_kernel *kinfo = NULL;
- int i;
-
-#ifdef CONFIG_OMAP_BOOT_TAG
- struct omap_board_config_entry *info = NULL;
-
- if (omap_bootloader_tag_len > 4)
- info = (struct omap_board_config_entry *) omap_bootloader_tag;
- while (info != NULL) {
- u8 *next;
-
- if (info->tag == tag) {
- if (skip == 0)
- break;
- skip--;
- }
-
- if ((info->len & 0x03) != 0) {
- /* We bail out to avoid an alignment fault */
- printk(KERN_ERR "OMAP peripheral config: Length (%d) not word-aligned (tag %04x)\n",
- info->len, info->tag);
- return NULL;
- }
- next = (u8 *) info + sizeof(*info) + info->len;
- if (next >= omap_bootloader_tag + omap_bootloader_tag_len)
- info = NULL;
- else
- info = (struct omap_board_config_entry *) next;
- }
- if (info != NULL) {
- /* Check the length as a lame attempt to check for
- * binary inconsistancy. */
- if (len != NO_LENGTH_CHECK) {
- /* Word-align len */
- if (len & 0x03)
- len = (len + 3) & ~0x03;
- if (info->len != len) {
- printk(KERN_ERR "OMAP peripheral config: Length mismatch with tag %x (want %d, got %d)\n",
- tag, len, info->len);
- return NULL;
- }
- }
- if (len_out != NULL)
- *len_out = info->len;
- return info->data;
- }
-#endif
- /* Try to find the config from the board-specific structures
- * in the kernel. */
- for (i = 0; i < omap_board_config_size; i++) {
- if (omap_board_config[i].tag == tag) {
- kinfo = &omap_board_config[i];
- break;
- }
- }
- if (kinfo == NULL)
- return NULL;
- return kinfo->data;
-}
-
-const void *__omap_get_config(u16 tag, size_t len, int nr)
-{
- return get_config(tag, len, nr, NULL);
-}
-EXPORT_SYMBOL(__omap_get_config);
-
-const void *omap_get_var_config(u16 tag, size_t *len)
-{
- return get_config(tag, NO_LENGTH_CHECK, 0, len);
-}
-EXPORT_SYMBOL(omap_get_var_config);
-
-static int __init omap_add_serial_console(void)
-{
- const struct omap_serial_console_config *info;
-
- info = omap_get_config(OMAP_TAG_SERIAL_CONSOLE,
- struct omap_serial_console_config);
- if (info != NULL && info->console_uart) {
- static char speed[11], *opt = NULL;
-
- if (info->console_speed) {
- snprintf(speed, sizeof(speed), "%u", info->console_speed);
- opt = speed;
- }
- return add_preferred_console("ttyS", info->console_uart - 1, opt);
- }
- return 0;
-}
-console_initcall(omap_add_serial_console);
+++ /dev/null
-/*
- * linux/arch/arm/mach-omap/common.h
- *
- * Header for code common to all OMAP machines.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#ifndef __ARCH_ARM_MACH_OMAP_COMMON_H
-#define __ARCH_ARM_MACH_OMAP_COMMON_H
-
-struct sys_timer;
-
-extern void omap_map_common_io(void);
-extern struct sys_timer omap_timer;
-extern void omap_serial_init(int ports[]);
-
-#endif /* __ARCH_ARM_MACH_OMAP_COMMON_H */
+++ /dev/null
-/*
- * linux/arch/arm/omap/dma.c
- *
- * Copyright (C) 2003 Nokia Corporation
- * Author: Juha Yrjölä <juha.yrjola@nokia.com>
- * DMA channel linking for 1610 by Samuel Ortiz <samuel.ortiz@nokia.com>
- * Graphics DMA and LCD DMA graphics tranformations
- * by Imre Deak <imre.deak@nokia.com>
- * Some functions based on earlier dma-omap.c Copyright (C) 2001 RidgeRun, Inc.
- *
- * Support functions for the OMAP internal DMA channels.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- */
-
-#include <linux/module.h>
-#include <linux/init.h>
-#include <linux/sched.h>
-#include <linux/spinlock.h>
-#include <linux/errno.h>
-#include <linux/interrupt.h>
-
-#include <asm/system.h>
-#include <asm/irq.h>
-#include <asm/hardware.h>
-#include <asm/dma.h>
-#include <asm/io.h>
-
-#include <asm/arch/tc.h>
-
-#define OMAP_DMA_ACTIVE 0x01
-
-#define OMAP_DMA_CCR_EN (1 << 7)
-
-#define OMAP_FUNC_MUX_ARM_BASE (0xfffe1000 + 0xec)
-
-static int enable_1510_mode = 0;
-
-struct omap_dma_lch {
- int next_lch;
- int dev_id;
- u16 saved_csr;
- u16 enabled_irqs;
- const char *dev_name;
- void (* callback)(int lch, u16 ch_status, void *data);
- void *data;
- long flags;
-};
-
-static int dma_chan_count;
-
-static spinlock_t dma_chan_lock;
-static struct omap_dma_lch dma_chan[OMAP_LOGICAL_DMA_CH_COUNT];
-
-const static u8 dma_irq[OMAP_LOGICAL_DMA_CH_COUNT] = {
- INT_DMA_CH0_6, INT_DMA_CH1_7, INT_DMA_CH2_8, INT_DMA_CH3,
- INT_DMA_CH4, INT_DMA_CH5, INT_1610_DMA_CH6, INT_1610_DMA_CH7,
- INT_1610_DMA_CH8, INT_1610_DMA_CH9, INT_1610_DMA_CH10,
- INT_1610_DMA_CH11, INT_1610_DMA_CH12, INT_1610_DMA_CH13,
- INT_1610_DMA_CH14, INT_1610_DMA_CH15, INT_DMA_LCD
-};
-
-static inline int get_gdma_dev(int req)
-{
- u32 reg = OMAP_FUNC_MUX_ARM_BASE + ((req - 1) / 5) * 4;
- int shift = ((req - 1) % 5) * 6;
-
- return ((omap_readl(reg) >> shift) & 0x3f) + 1;
-}
-
-static inline void set_gdma_dev(int req, int dev)
-{
- u32 reg = OMAP_FUNC_MUX_ARM_BASE + ((req - 1) / 5) * 4;
- int shift = ((req - 1) % 5) * 6;
- u32 l;
-
- l = omap_readl(reg);
- l &= ~(0x3f << shift);
- l |= (dev - 1) << shift;
- omap_writel(l, reg);
-}
-
-static void clear_lch_regs(int lch)
-{
- int i;
- u32 lch_base = OMAP_DMA_BASE + lch * 0x40;
-
- for (i = 0; i < 0x2c; i += 2)
- omap_writew(0, lch_base + i);
-}
-
-void omap_set_dma_priority(int dst_port, int priority)
-{
- unsigned long reg;
- u32 l;
-
- switch (dst_port) {
- case OMAP_DMA_PORT_OCP_T1: /* FFFECC00 */
- reg = OMAP_TC_OCPT1_PRIOR;
- break;
- case OMAP_DMA_PORT_OCP_T2: /* FFFECCD0 */
- reg = OMAP_TC_OCPT2_PRIOR;
- break;
- case OMAP_DMA_PORT_EMIFF: /* FFFECC08 */
- reg = OMAP_TC_EMIFF_PRIOR;
- break;
- case OMAP_DMA_PORT_EMIFS: /* FFFECC04 */
- reg = OMAP_TC_EMIFS_PRIOR;
- break;
- default:
- BUG();
- return;
- }
- l = omap_readl(reg);
- l &= ~(0xf << 8);
- l |= (priority & 0xf) << 8;
- omap_writel(l, reg);
-}
-
-void omap_set_dma_transfer_params(int lch, int data_type, int elem_count,
- int frame_count, int sync_mode)
-{
- u16 w;
-
- w = omap_readw(OMAP_DMA_CSDP(lch));
- w &= ~0x03;
- w |= data_type;
- omap_writew(w, OMAP_DMA_CSDP(lch));
-
- w = omap_readw(OMAP_DMA_CCR(lch));
- w &= ~(1 << 5);
- if (sync_mode == OMAP_DMA_SYNC_FRAME)
- w |= 1 << 5;
- omap_writew(w, OMAP_DMA_CCR(lch));
-
- w = omap_readw(OMAP_DMA_CCR2(lch));
- w &= ~(1 << 2);
- if (sync_mode == OMAP_DMA_SYNC_BLOCK)
- w |= 1 << 2;
- omap_writew(w, OMAP_DMA_CCR2(lch));
-
- omap_writew(elem_count, OMAP_DMA_CEN(lch));
- omap_writew(frame_count, OMAP_DMA_CFN(lch));
-
-}
-void omap_set_dma_color_mode(int lch, enum omap_dma_color_mode mode, u32 color)
-{
- u16 w;
-
- BUG_ON(omap_dma_in_1510_mode());
-
- w = omap_readw(OMAP_DMA_CCR2(lch)) & ~0x03;
- switch (mode) {
- case OMAP_DMA_CONSTANT_FILL:
- w |= 0x01;
- break;
- case OMAP_DMA_TRANSPARENT_COPY:
- w |= 0x02;
- break;
- case OMAP_DMA_COLOR_DIS:
- break;
- default:
- BUG();
- }
- omap_writew(w, OMAP_DMA_CCR2(lch));
-
- w = omap_readw(OMAP_DMA_LCH_CTRL(lch)) & ~0x0f;
- /* Default is channel type 2D */
- if (mode) {
- omap_writew((u16)color, OMAP_DMA_COLOR_L(lch));
- omap_writew((u16)(color >> 16), OMAP_DMA_COLOR_U(lch));
- w |= 1; /* Channel type G */
- }
- omap_writew(w, OMAP_DMA_LCH_CTRL(lch));
-}
-
-
-void omap_set_dma_src_params(int lch, int src_port, int src_amode,
- unsigned long src_start)
-{
- u16 w;
-
- w = omap_readw(OMAP_DMA_CSDP(lch));
- w &= ~(0x1f << 2);
- w |= src_port << 2;
- omap_writew(w, OMAP_DMA_CSDP(lch));
-
- w = omap_readw(OMAP_DMA_CCR(lch));
- w &= ~(0x03 << 12);
- w |= src_amode << 12;
- omap_writew(w, OMAP_DMA_CCR(lch));
-
- omap_writew(src_start >> 16, OMAP_DMA_CSSA_U(lch));
- omap_writew(src_start, OMAP_DMA_CSSA_L(lch));
-}
-
-void omap_set_dma_src_index(int lch, int eidx, int fidx)
-{
- omap_writew(eidx, OMAP_DMA_CSEI(lch));
- omap_writew(fidx, OMAP_DMA_CSFI(lch));
-}
-
-void omap_set_dma_src_data_pack(int lch, int enable)
-{
- u16 w;
-
- w = omap_readw(OMAP_DMA_CSDP(lch)) & ~(1 << 6);
- w |= enable ? (1 << 6) : 0;
- omap_writew(w, OMAP_DMA_CSDP(lch));
-}
-
-void omap_set_dma_src_burst_mode(int lch, enum omap_dma_burst_mode burst_mode)
-{
- u16 w;
-
- w = omap_readw(OMAP_DMA_CSDP(lch)) & ~(0x03 << 7);
- switch (burst_mode) {
- case OMAP_DMA_DATA_BURST_DIS:
- break;
- case OMAP_DMA_DATA_BURST_4:
- w |= (0x01 << 7);
- break;
- case OMAP_DMA_DATA_BURST_8:
- /* not supported by current hardware
- * w |= (0x03 << 7);
- * fall through
- */
- default:
- BUG();
- }
- omap_writew(w, OMAP_DMA_CSDP(lch));
-}
-
-void omap_set_dma_dest_params(int lch, int dest_port, int dest_amode,
- unsigned long dest_start)
-{
- u16 w;
-
- w = omap_readw(OMAP_DMA_CSDP(lch));
- w &= ~(0x1f << 9);
- w |= dest_port << 9;
- omap_writew(w, OMAP_DMA_CSDP(lch));
-
- w = omap_readw(OMAP_DMA_CCR(lch));
- w &= ~(0x03 << 14);
- w |= dest_amode << 14;
- omap_writew(w, OMAP_DMA_CCR(lch));
-
- omap_writew(dest_start >> 16, OMAP_DMA_CDSA_U(lch));
- omap_writew(dest_start, OMAP_DMA_CDSA_L(lch));
-}
-
-void omap_set_dma_dest_index(int lch, int eidx, int fidx)
-{
- omap_writew(eidx, OMAP_DMA_CDEI(lch));
- omap_writew(fidx, OMAP_DMA_CDFI(lch));
-}
-
-void omap_set_dma_dest_data_pack(int lch, int enable)
-{
- u16 w;
-
- w = omap_readw(OMAP_DMA_CSDP(lch)) & ~(1 << 13);
- w |= enable ? (1 << 13) : 0;
- omap_writew(w, OMAP_DMA_CSDP(lch));
-}
-
-void omap_set_dma_dest_burst_mode(int lch, enum omap_dma_burst_mode burst_mode)
-{
- u16 w;
-
- w = omap_readw(OMAP_DMA_CSDP(lch)) & ~(0x03 << 14);
- switch (burst_mode) {
- case OMAP_DMA_DATA_BURST_DIS:
- break;
- case OMAP_DMA_DATA_BURST_4:
- w |= (0x01 << 14);
- break;
- case OMAP_DMA_DATA_BURST_8:
- w |= (0x03 << 14);
- break;
- default:
- printk(KERN_ERR "Invalid DMA burst mode\n");
- BUG();
- return;
- }
- omap_writew(w, OMAP_DMA_CSDP(lch));
-}
-
-static inline void init_intr(int lch)
-{
- u16 w;
-
- /* Read CSR to make sure it's cleared. */
- w = omap_readw(OMAP_DMA_CSR(lch));
- /* Enable some nice interrupts. */
- omap_writew(dma_chan[lch].enabled_irqs, OMAP_DMA_CICR(lch));
- dma_chan[lch].flags |= OMAP_DMA_ACTIVE;
-}
-
-static inline void enable_lnk(int lch)
-{
- u16 w;
-
- /* Clear the STOP_LNK bits */
- w = omap_readw(OMAP_DMA_CLNK_CTRL(lch));
- w &= ~(1 << 14);
- omap_writew(w, OMAP_DMA_CLNK_CTRL(lch));
-
- /* And set the ENABLE_LNK bits */
- if (dma_chan[lch].next_lch != -1)
- omap_writew(dma_chan[lch].next_lch | (1 << 15),
- OMAP_DMA_CLNK_CTRL(lch));
-}
-
-static inline void disable_lnk(int lch)
-{
- u16 w;
-
- /* Disable interrupts */
- omap_writew(0, OMAP_DMA_CICR(lch));
-
- /* Set the STOP_LNK bit */
- w = omap_readw(OMAP_DMA_CLNK_CTRL(lch));
- w |= (1 << 14);
- w = omap_writew(w, OMAP_DMA_CLNK_CTRL(lch));
-
- dma_chan[lch].flags &= ~OMAP_DMA_ACTIVE;
-}
-
-void omap_start_dma(int lch)
-{
- u16 w;
-
- if (!omap_dma_in_1510_mode() && dma_chan[lch].next_lch != -1) {
- int next_lch, cur_lch;
- char dma_chan_link_map[OMAP_LOGICAL_DMA_CH_COUNT];
-
- dma_chan_link_map[lch] = 1;
- /* Set the link register of the first channel */
- enable_lnk(lch);
-
- memset(dma_chan_link_map, 0, sizeof(dma_chan_link_map));
- cur_lch = dma_chan[lch].next_lch;
- do {
- next_lch = dma_chan[cur_lch].next_lch;
-
- /* The loop case: we've been here already */
- if (dma_chan_link_map[cur_lch])
- break;
- /* Mark the current channel */
- dma_chan_link_map[cur_lch] = 1;
-
- enable_lnk(cur_lch);
- init_intr(cur_lch);
-
- cur_lch = next_lch;
- } while (next_lch != -1);
- }
-
- init_intr(lch);
-
- w = omap_readw(OMAP_DMA_CCR(lch));
- w |= OMAP_DMA_CCR_EN;
- omap_writew(w, OMAP_DMA_CCR(lch));
- dma_chan[lch].flags |= OMAP_DMA_ACTIVE;
-}
-
-void omap_stop_dma(int lch)
-{
- u16 w;
-
- if (!omap_dma_in_1510_mode() && dma_chan[lch].next_lch != -1) {
- int next_lch, cur_lch = lch;
- char dma_chan_link_map[OMAP_LOGICAL_DMA_CH_COUNT];
-
- memset(dma_chan_link_map, 0, sizeof(dma_chan_link_map));
- do {
- /* The loop case: we've been here already */
- if (dma_chan_link_map[cur_lch])
- break;
- /* Mark the current channel */
- dma_chan_link_map[cur_lch] = 1;
-
- disable_lnk(cur_lch);
-
- next_lch = dma_chan[cur_lch].next_lch;
- cur_lch = next_lch;
- } while (next_lch != -1);
-
- return;
- }
- /* Disable all interrupts on the channel */
- omap_writew(0, OMAP_DMA_CICR(lch));
-
- w = omap_readw(OMAP_DMA_CCR(lch));
- w &= ~OMAP_DMA_CCR_EN;
- omap_writew(w, OMAP_DMA_CCR(lch));
- dma_chan[lch].flags &= ~OMAP_DMA_ACTIVE;
-}
-
-void omap_enable_dma_irq(int lch, u16 bits)
-{
- dma_chan[lch].enabled_irqs |= bits;
-}
-
-void omap_disable_dma_irq(int lch, u16 bits)
-{
- dma_chan[lch].enabled_irqs &= ~bits;
-}
-
-static int dma_handle_ch(int ch)
-{
- u16 csr;
-
- if (enable_1510_mode && ch >= 6) {
- csr = dma_chan[ch].saved_csr;
- dma_chan[ch].saved_csr = 0;
- } else
- csr = omap_readw(OMAP_DMA_CSR(ch));
- if (enable_1510_mode && ch <= 2 && (csr >> 7) != 0) {
- dma_chan[ch + 6].saved_csr = csr >> 7;
- csr &= 0x7f;
- }
- if (!csr)
- return 0;
- if (unlikely(dma_chan[ch].dev_id == -1)) {
- printk(KERN_WARNING "Spurious interrupt from DMA channel %d (CSR %04x)\n",
- ch, csr);
- return 0;
- }
- if (unlikely(csr & OMAP_DMA_TOUT_IRQ))
- printk(KERN_WARNING "DMA timeout with device %d\n", dma_chan[ch].dev_id);
- if (unlikely(csr & OMAP_DMA_DROP_IRQ))
- printk(KERN_WARNING "DMA synchronization event drop occurred with device %d\n",
- dma_chan[ch].dev_id);
- if (likely(csr & OMAP_DMA_BLOCK_IRQ))
- dma_chan[ch].flags &= ~OMAP_DMA_ACTIVE;
- if (likely(dma_chan[ch].callback != NULL))
- dma_chan[ch].callback(ch, csr, dma_chan[ch].data);
- return 1;
-}
-
-static irqreturn_t dma_irq_handler(int irq, void *dev_id, struct pt_regs *regs)
-{
- int ch = ((int) dev_id) - 1;
- int handled = 0;
-
- for (;;) {
- int handled_now = 0;
-
- handled_now += dma_handle_ch(ch);
- if (enable_1510_mode && dma_chan[ch + 6].saved_csr)
- handled_now += dma_handle_ch(ch + 6);
- if (!handled_now)
- break;
- handled += handled_now;
- }
-
- return handled ? IRQ_HANDLED : IRQ_NONE;
-}
-
-int omap_request_dma(int dev_id, const char *dev_name,
- void (* callback)(int lch, u16 ch_status, void *data),
- void *data, int *dma_ch_out)
-{
- int ch, free_ch = -1;
- unsigned long flags;
- struct omap_dma_lch *chan;
-
- spin_lock_irqsave(&dma_chan_lock, flags);
- for (ch = 0; ch < dma_chan_count; ch++) {
- if (free_ch == -1 && dma_chan[ch].dev_id == -1) {
- free_ch = ch;
- if (dev_id == 0)
- break;
- }
- }
- if (free_ch == -1) {
- spin_unlock_irqrestore(&dma_chan_lock, flags);
- return -EBUSY;
- }
- chan = dma_chan + free_ch;
- chan->dev_id = dev_id;
- clear_lch_regs(free_ch);
- spin_unlock_irqrestore(&dma_chan_lock, flags);
-
- chan->dev_id = dev_id;
- chan->dev_name = dev_name;
- chan->callback = callback;
- chan->data = data;
- chan->enabled_irqs = OMAP_DMA_TOUT_IRQ | OMAP_DMA_DROP_IRQ | OMAP_DMA_BLOCK_IRQ;
-
- if (cpu_is_omap16xx()) {
- /* If the sync device is set, configure it dynamically. */
- if (dev_id != 0) {
- set_gdma_dev(free_ch + 1, dev_id);
- dev_id = free_ch + 1;
- }
- /* Disable the 1510 compatibility mode and set the sync device
- * id. */
- omap_writew(dev_id | (1 << 10), OMAP_DMA_CCR(free_ch));
- } else {
- omap_writew(dev_id, OMAP_DMA_CCR(free_ch));
- }
- *dma_ch_out = free_ch;
-
- return 0;
-}
-
-void omap_free_dma(int ch)
-{
- unsigned long flags;
-
- spin_lock_irqsave(&dma_chan_lock, flags);
- if (dma_chan[ch].dev_id == -1) {
- printk("omap_dma: trying to free nonallocated DMA channel %d\n", ch);
- spin_unlock_irqrestore(&dma_chan_lock, flags);
- return;
- }
- dma_chan[ch].dev_id = -1;
- spin_unlock_irqrestore(&dma_chan_lock, flags);
-
- /* Disable all DMA interrupts for the channel. */
- omap_writew(0, OMAP_DMA_CICR(ch));
- /* Make sure the DMA transfer is stopped. */
- omap_writew(0, OMAP_DMA_CCR(ch));
-}
-
-int omap_dma_in_1510_mode(void)
-{
- return enable_1510_mode;
-}
-
-/*
- * lch_queue DMA will start right after lch_head one is finished.
- * For this DMA link to start, you still need to start (see omap_start_dma)
- * the first one. That will fire up the entire queue.
- */
-void omap_dma_link_lch (int lch_head, int lch_queue)
-{
- if (omap_dma_in_1510_mode()) {
- printk(KERN_ERR "DMA linking is not supported in 1510 mode\n");
- BUG();
- return;
- }
-
- if ((dma_chan[lch_head].dev_id == -1) ||
- (dma_chan[lch_queue].dev_id == -1)) {
- printk(KERN_ERR "omap_dma: trying to link non requested channels\n");
- dump_stack();
- }
-
- dma_chan[lch_head].next_lch = lch_queue;
-}
-
-/*
- * Once the DMA queue is stopped, we can destroy it.
- */
-void omap_dma_unlink_lch (int lch_head, int lch_queue)
-{
- if (omap_dma_in_1510_mode()) {
- printk(KERN_ERR "DMA linking is not supported in 1510 mode\n");
- BUG();
- return;
- }
-
- if (dma_chan[lch_head].next_lch != lch_queue ||
- dma_chan[lch_head].next_lch == -1) {
- printk(KERN_ERR "omap_dma: trying to unlink non linked channels\n");
- dump_stack();
- }
-
-
- if ((dma_chan[lch_head].flags & OMAP_DMA_ACTIVE) ||
- (dma_chan[lch_head].flags & OMAP_DMA_ACTIVE)) {
- printk(KERN_ERR "omap_dma: You need to stop the DMA channels before unlinking\n");
- dump_stack();
- }
-
- dma_chan[lch_head].next_lch = -1;
-}
-
-
-static struct lcd_dma_info {
- spinlock_t lock;
- int reserved;
- void (* callback)(u16 status, void *data);
- void *cb_data;
-
- int active;
- unsigned long addr, size;
- int rotate, data_type, xres, yres;
- int vxres;
- int mirror;
- int xscale, yscale;
- int ext_ctrl;
- int src_port;
- int single_transfer;
-} lcd_dma;
-
-void omap_set_lcd_dma_b1(unsigned long addr, u16 fb_xres, u16 fb_yres,
- int data_type)
-{
- lcd_dma.addr = addr;
- lcd_dma.data_type = data_type;
- lcd_dma.xres = fb_xres;
- lcd_dma.yres = fb_yres;
-}
-
-void omap_set_lcd_dma_src_port(int port)
-{
- lcd_dma.src_port = port;
-}
-
-void omap_set_lcd_dma_ext_controller(int external)
-{
- lcd_dma.ext_ctrl = external;
-}
-
-void omap_set_lcd_dma_single_transfer(int single)
-{
- lcd_dma.single_transfer = single;
-}
-
-
-void omap_set_lcd_dma_b1_rotation(int rotate)
-{
- if (omap_dma_in_1510_mode()) {
- printk(KERN_ERR "DMA rotation is not supported in 1510 mode\n");
- BUG();
- return;
- }
- lcd_dma.rotate = rotate;
-}
-
-void omap_set_lcd_dma_b1_mirror(int mirror)
-{
- if (omap_dma_in_1510_mode()) {
- printk(KERN_ERR "DMA mirror is not supported in 1510 mode\n");
- BUG();
- }
- lcd_dma.mirror = mirror;
-}
-
-void omap_set_lcd_dma_b1_vxres(unsigned long vxres)
-{
- if (omap_dma_in_1510_mode()) {
- printk(KERN_ERR "DMA virtual resulotion is not supported "
- "in 1510 mode\n");
- BUG();
- }
- lcd_dma.vxres = vxres;
-}
-
-void omap_set_lcd_dma_b1_scale(unsigned int xscale, unsigned int yscale)
-{
- if (omap_dma_in_1510_mode()) {
- printk(KERN_ERR "DMA scale is not supported in 1510 mode\n");
- BUG();
- }
- lcd_dma.xscale = xscale;
- lcd_dma.yscale = yscale;
-}
-
-static void set_b1_regs(void)
-{
- unsigned long top, bottom;
- int es;
- u16 w;
- unsigned long en, fn;
- long ei, fi;
- unsigned long vxres;
- unsigned int xscale, yscale;
-
- switch (lcd_dma.data_type) {
- case OMAP_DMA_DATA_TYPE_S8:
- es = 1;
- break;
- case OMAP_DMA_DATA_TYPE_S16:
- es = 2;
- break;
- case OMAP_DMA_DATA_TYPE_S32:
- es = 4;
- break;
- default:
- BUG();
- return;
- }
-
- vxres = lcd_dma.vxres ? lcd_dma.vxres : lcd_dma.xres;
- xscale = lcd_dma.xscale ? lcd_dma.xscale : 1;
- yscale = lcd_dma.yscale ? lcd_dma.yscale : 1;
- BUG_ON(vxres < lcd_dma.xres);
-#define PIXADDR(x,y) (lcd_dma.addr + ((y) * vxres * yscale + (x) * xscale) * es)
-#define PIXSTEP(sx, sy, dx, dy) (PIXADDR(dx, dy) - PIXADDR(sx, sy) - es + 1)
- switch (lcd_dma.rotate) {
- case 0:
- if (!lcd_dma.mirror) {
- top = PIXADDR(0, 0);
- bottom = PIXADDR(lcd_dma.xres - 1, lcd_dma.yres - 1);
- /* 1510 DMA requires the bottom address to be 2 more
- * than the actual last memory access location. */
- if (omap_dma_in_1510_mode() &&
- lcd_dma.data_type == OMAP_DMA_DATA_TYPE_S32)
- bottom += 2;
- ei = PIXSTEP(0, 0, 1, 0);
- fi = PIXSTEP(lcd_dma.xres - 1, 0, 0, 1);
- } else {
- top = PIXADDR(lcd_dma.xres - 1, 0);
- bottom = PIXADDR(0, lcd_dma.yres - 1);
- ei = PIXSTEP(1, 0, 0, 0);
- fi = PIXSTEP(0, 0, lcd_dma.xres - 1, 1);
- }
- en = lcd_dma.xres;
- fn = lcd_dma.yres;
- break;
- case 90:
- if (!lcd_dma.mirror) {
- top = PIXADDR(0, lcd_dma.yres - 1);
- bottom = PIXADDR(lcd_dma.xres - 1, 0);
- ei = PIXSTEP(0, 1, 0, 0);
- fi = PIXSTEP(0, 0, 1, lcd_dma.yres - 1);
- } else {
- top = PIXADDR(lcd_dma.xres - 1, lcd_dma.yres - 1);
- bottom = PIXADDR(0, 0);
- ei = PIXSTEP(0, 1, 0, 0);
- fi = PIXSTEP(1, 0, 0, lcd_dma.yres - 1);
- }
- en = lcd_dma.yres;
- fn = lcd_dma.xres;
- break;
- case 180:
- if (!lcd_dma.mirror) {
- top = PIXADDR(lcd_dma.xres - 1, lcd_dma.yres - 1);
- bottom = PIXADDR(0, 0);
- ei = PIXSTEP(1, 0, 0, 0);
- fi = PIXSTEP(0, 1, lcd_dma.xres - 1, 0);
- } else {
- top = PIXADDR(0, lcd_dma.yres - 1);
- bottom = PIXADDR(lcd_dma.xres - 1, 0);
- ei = PIXSTEP(0, 0, 1, 0);
- fi = PIXSTEP(lcd_dma.xres - 1, 1, 0, 0);
- }
- en = lcd_dma.xres;
- fn = lcd_dma.yres;
- break;
- case 270:
- if (!lcd_dma.mirror) {
- top = PIXADDR(lcd_dma.xres - 1, 0);
- bottom = PIXADDR(0, lcd_dma.yres - 1);
- ei = PIXSTEP(0, 0, 0, 1);
- fi = PIXSTEP(1, lcd_dma.yres - 1, 0, 0);
- } else {
- top = PIXADDR(0, 0);
- bottom = PIXADDR(lcd_dma.xres - 1, lcd_dma.yres - 1);
- ei = PIXSTEP(0, 0, 0, 1);
- fi = PIXSTEP(0, lcd_dma.yres - 1, 1, 0);
- }
- en = lcd_dma.yres;
- fn = lcd_dma.xres;
- break;
- default:
- BUG();
- return; /* Supress warning about uninitialized vars */
- }
-
- if (omap_dma_in_1510_mode()) {
- omap_writew(top >> 16, OMAP1510_DMA_LCD_TOP_F1_U);
- omap_writew(top, OMAP1510_DMA_LCD_TOP_F1_L);
- omap_writew(bottom >> 16, OMAP1510_DMA_LCD_BOT_F1_U);
- omap_writew(bottom, OMAP1510_DMA_LCD_BOT_F1_L);
-
- return;
- }
-
- /* 1610 regs */
- omap_writew(top >> 16, OMAP1610_DMA_LCD_TOP_B1_U);
- omap_writew(top, OMAP1610_DMA_LCD_TOP_B1_L);
- omap_writew(bottom >> 16, OMAP1610_DMA_LCD_BOT_B1_U);
- omap_writew(bottom, OMAP1610_DMA_LCD_BOT_B1_L);
-
- omap_writew(en, OMAP1610_DMA_LCD_SRC_EN_B1);
- omap_writew(fn, OMAP1610_DMA_LCD_SRC_FN_B1);
-
- w = omap_readw(OMAP1610_DMA_LCD_CSDP);
- w &= ~0x03;
- w |= lcd_dma.data_type;
- omap_writew(w, OMAP1610_DMA_LCD_CSDP);
-
- w = omap_readw(OMAP1610_DMA_LCD_CTRL);
- /* Always set the source port as SDRAM for now*/
- w &= ~(0x03 << 6);
- if (lcd_dma.ext_ctrl)
- w |= 1 << 8;
- else
- w &= ~(1 << 8);
- if (lcd_dma.callback != NULL)
- w |= 1 << 1; /* Block interrupt enable */
- else
- w &= ~(1 << 1);
- omap_writew(w, OMAP1610_DMA_LCD_CTRL);
-
- if (!(lcd_dma.rotate || lcd_dma.mirror ||
- lcd_dma.vxres || lcd_dma.xscale || lcd_dma.yscale))
- return;
-
- w = omap_readw(OMAP1610_DMA_LCD_CCR);
- /* Set the double-indexed addressing mode */
- w |= (0x03 << 12);
- omap_writew(w, OMAP1610_DMA_LCD_CCR);
-
- omap_writew(ei, OMAP1610_DMA_LCD_SRC_EI_B1);
- omap_writew(fi >> 16, OMAP1610_DMA_LCD_SRC_FI_B1_U);
- omap_writew(fi, OMAP1610_DMA_LCD_SRC_FI_B1_L);
-}
-
-static irqreturn_t lcd_dma_irq_handler(int irq, void *dev_id, struct pt_regs *regs)
-{
- u16 w;
-
- w = omap_readw(OMAP1610_DMA_LCD_CTRL);
- if (unlikely(!(w & (1 << 3)))) {
- printk(KERN_WARNING "Spurious LCD DMA IRQ\n");
- return IRQ_NONE;
- }
- /* Ack the IRQ */
- w |= (1 << 3);
- omap_writew(w, OMAP1610_DMA_LCD_CTRL);
- lcd_dma.active = 0;
- if (lcd_dma.callback != NULL)
- lcd_dma.callback(w, lcd_dma.cb_data);
-
- return IRQ_HANDLED;
-}
-
-int omap_request_lcd_dma(void (* callback)(u16 status, void *data),
- void *data)
-{
- spin_lock_irq(&lcd_dma.lock);
- if (lcd_dma.reserved) {
- spin_unlock_irq(&lcd_dma.lock);
- printk(KERN_ERR "LCD DMA channel already reserved\n");
- BUG();
- return -EBUSY;
- }
- lcd_dma.reserved = 1;
- spin_unlock_irq(&lcd_dma.lock);
- lcd_dma.callback = callback;
- lcd_dma.cb_data = data;
- lcd_dma.active = 0;
- lcd_dma.single_transfer = 0;
- lcd_dma.rotate = 0;
- lcd_dma.vxres = 0;
- lcd_dma.mirror = 0;
- lcd_dma.xscale = 0;
- lcd_dma.yscale = 0;
- lcd_dma.ext_ctrl = 0;
- lcd_dma.src_port = 0;
-
- return 0;
-}
-
-void omap_free_lcd_dma(void)
-{
- spin_lock(&lcd_dma.lock);
- if (!lcd_dma.reserved) {
- spin_unlock(&lcd_dma.lock);
- printk(KERN_ERR "LCD DMA is not reserved\n");
- BUG();
- return;
- }
- if (!enable_1510_mode)
- omap_writew(omap_readw(OMAP1610_DMA_LCD_CCR) & ~1, OMAP1610_DMA_LCD_CCR);
- lcd_dma.reserved = 0;
- spin_unlock(&lcd_dma.lock);
-}
-
-void omap_enable_lcd_dma(void)
-{
- u16 w;
-
- /* Set the Enable bit only if an external controller is
- * connected. Otherwise the OMAP internal controller will
- * start the transfer when it gets enabled.
- */
- if (enable_1510_mode || !lcd_dma.ext_ctrl)
- return;
- w = omap_readw(OMAP1610_DMA_LCD_CCR);
- w |= 1 << 7;
- omap_writew(w, OMAP1610_DMA_LCD_CCR);
- lcd_dma.active = 1;
-}
-
-void omap_setup_lcd_dma(void)
-{
- BUG_ON(lcd_dma.active);
- if (!enable_1510_mode) {
- /* Set some reasonable defaults */
- omap_writew(0x5440, OMAP1610_DMA_LCD_CCR);
- omap_writew(0x9102, OMAP1610_DMA_LCD_CSDP);
- omap_writew(0x0004, OMAP1610_DMA_LCD_LCH_CTRL);
- }
- set_b1_regs();
- if (!enable_1510_mode) {
- u16 w;
-
- w = omap_readw(OMAP1610_DMA_LCD_CCR);
- /* If DMA was already active set the end_prog bit to have
- * the programmed register set loaded into the active
- * register set.
- */
- w |= 1 << 11; /* End_prog */
- if (!lcd_dma.single_transfer)
- w |= (3 << 8); /* Auto_init, repeat */
- omap_writew(w, OMAP1610_DMA_LCD_CCR);
- }
-}
-
-void omap_stop_lcd_dma(void)
-{
- lcd_dma.active = 0;
- if (!enable_1510_mode && lcd_dma.ext_ctrl)
- omap_writew(omap_readw(OMAP1610_DMA_LCD_CCR) & ~(1 << 7),
- OMAP1610_DMA_LCD_CCR);
-}
-
-/*
- * Clears any DMA state so the DMA engine is ready to restart with new buffers
- * through omap_start_dma(). Any buffers in flight are discarded.
- */
-void omap_clear_dma(int lch)
-{
- unsigned long flags;
- int status;
-
- local_irq_save(flags);
- omap_writew(omap_readw(OMAP_DMA_CCR(lch)) & ~OMAP_DMA_CCR_EN,
- OMAP_DMA_CCR(lch));
- status = OMAP_DMA_CSR(lch); /* clear pending interrupts */
- local_irq_restore(flags);
-}
-
-/*
- * Returns current physical source address for the given DMA channel.
- * If the channel is running the caller must disable interrupts prior calling
- * this function and process the returned value before re-enabling interrupt to
- * prevent races with the interrupt handler. Note that in continuous mode there
- * is a chance for CSSA_L register overflow inbetween the two reads resulting
- * in incorrect return value.
- */
-dma_addr_t omap_get_dma_src_pos(int lch)
-{
- return (dma_addr_t) (OMAP_DMA_CSSA_L(lch) |
- (OMAP_DMA_CSSA_U(lch) << 16));
-}
-
-/*
- * Returns current physical destination address for the given DMA channel.
- * If the channel is running the caller must disable interrupts prior calling
- * this function and process the returned value before re-enabling interrupt to
- * prevent races with the interrupt handler. Note that in continuous mode there
- * is a chance for CDSA_L register overflow inbetween the two reads resulting
- * in incorrect return value.
- */
-dma_addr_t omap_get_dma_dst_pos(int lch)
-{
- return (dma_addr_t) (OMAP_DMA_CDSA_L(lch) |
- (OMAP_DMA_CDSA_U(lch) << 16));
-}
-
-static int __init omap_init_dma(void)
-{
- int ch, r;
-
- if (cpu_is_omap1510()) {
- printk(KERN_INFO "DMA support for OMAP1510 initialized\n");
- dma_chan_count = 9;
- enable_1510_mode = 1;
- } else if (cpu_is_omap16xx() || cpu_is_omap730()) {
- printk(KERN_INFO "OMAP DMA hardware version %d\n",
- omap_readw(OMAP_DMA_HW_ID));
- printk(KERN_INFO "DMA capabilities: %08x:%08x:%04x:%04x:%04x\n",
- (omap_readw(OMAP_DMA_CAPS_0_U) << 16) | omap_readw(OMAP_DMA_CAPS_0_L),
- (omap_readw(OMAP_DMA_CAPS_1_U) << 16) | omap_readw(OMAP_DMA_CAPS_1_L),
- omap_readw(OMAP_DMA_CAPS_2), omap_readw(OMAP_DMA_CAPS_3),
- omap_readw(OMAP_DMA_CAPS_4));
- if (!enable_1510_mode) {
- u16 w;
-
- /* Disable OMAP 3.0/3.1 compatibility mode. */
- w = omap_readw(OMAP_DMA_GSCR);
- w |= 1 << 3;
- omap_writew(w, OMAP_DMA_GSCR);
- dma_chan_count = 16;
- } else
- dma_chan_count = 9;
- } else {
- dma_chan_count = 0;
- return 0;
- }
-
- memset(&lcd_dma, 0, sizeof(lcd_dma));
- spin_lock_init(&lcd_dma.lock);
- spin_lock_init(&dma_chan_lock);
- memset(&dma_chan, 0, sizeof(dma_chan));
-
- for (ch = 0; ch < dma_chan_count; ch++) {
- dma_chan[ch].dev_id = -1;
- dma_chan[ch].next_lch = -1;
-
- if (ch >= 6 && enable_1510_mode)
- continue;
-
- /* request_irq() doesn't like dev_id (ie. ch) being zero,
- * so we have to kludge around this. */
- r = request_irq(dma_irq[ch], dma_irq_handler, 0, "DMA",
- (void *) (ch + 1));
- if (r != 0) {
- int i;
-
- printk(KERN_ERR "unable to request IRQ %d for DMA (error %d)\n",
- dma_irq[ch], r);
- for (i = 0; i < ch; i++)
- free_irq(dma_irq[i], (void *) (i + 1));
- return r;
- }
- }
- r = request_irq(INT_DMA_LCD, lcd_dma_irq_handler, 0, "LCD DMA", NULL);
- if (r != 0) {
- int i;
-
- printk(KERN_ERR "unable to request IRQ for LCD DMA (error %d)\n", r);
- for (i = 0; i < dma_chan_count; i++)
- free_irq(dma_irq[i], (void *) (i + 1));
- return r;
- }
- return 0;
-}
-
-arch_initcall(omap_init_dma);
-
-
-EXPORT_SYMBOL(omap_get_dma_src_pos);
-EXPORT_SYMBOL(omap_get_dma_dst_pos);
-EXPORT_SYMBOL(omap_clear_dma);
-EXPORT_SYMBOL(omap_set_dma_priority);
-EXPORT_SYMBOL(omap_request_dma);
-EXPORT_SYMBOL(omap_free_dma);
-EXPORT_SYMBOL(omap_start_dma);
-EXPORT_SYMBOL(omap_stop_dma);
-EXPORT_SYMBOL(omap_enable_dma_irq);
-EXPORT_SYMBOL(omap_disable_dma_irq);
-
-EXPORT_SYMBOL(omap_set_dma_transfer_params);
-EXPORT_SYMBOL(omap_set_dma_color_mode);
-
-EXPORT_SYMBOL(omap_set_dma_src_params);
-EXPORT_SYMBOL(omap_set_dma_src_index);
-EXPORT_SYMBOL(omap_set_dma_src_data_pack);
-EXPORT_SYMBOL(omap_set_dma_src_burst_mode);
-
-EXPORT_SYMBOL(omap_set_dma_dest_params);
-EXPORT_SYMBOL(omap_set_dma_dest_index);
-EXPORT_SYMBOL(omap_set_dma_dest_data_pack);
-EXPORT_SYMBOL(omap_set_dma_dest_burst_mode);
-
-EXPORT_SYMBOL(omap_dma_link_lch);
-EXPORT_SYMBOL(omap_dma_unlink_lch);
-
-EXPORT_SYMBOL(omap_request_lcd_dma);
-EXPORT_SYMBOL(omap_free_lcd_dma);
-EXPORT_SYMBOL(omap_enable_lcd_dma);
-EXPORT_SYMBOL(omap_setup_lcd_dma);
-EXPORT_SYMBOL(omap_stop_lcd_dma);
-EXPORT_SYMBOL(omap_set_lcd_dma_b1);
-EXPORT_SYMBOL(omap_set_lcd_dma_single_transfer);
-EXPORT_SYMBOL(omap_set_lcd_dma_ext_controller);
-EXPORT_SYMBOL(omap_set_lcd_dma_b1_rotation);
-EXPORT_SYMBOL(omap_set_lcd_dma_b1_vxres);
-EXPORT_SYMBOL(omap_set_lcd_dma_b1_scale);
-EXPORT_SYMBOL(omap_set_lcd_dma_b1_mirror);
-
+++ /dev/null
-/*
- * linux/arch/arm/mach-omap/gpio.c
- *
- * Support functions for OMAP GPIO
- *
- * Copyright (C) 2003 Nokia Corporation
- * Written by Juha Yrjölä <juha.yrjola@nokia.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/config.h>
-#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/sched.h>
-#include <linux/interrupt.h>
-#include <linux/ptrace.h>
-
-#include <asm/hardware.h>
-#include <asm/irq.h>
-#include <asm/arch/irqs.h>
-#include <asm/arch/gpio.h>
-#include <asm/mach/irq.h>
-
-#include <asm/io.h>
-
-/*
- * OMAP1510 GPIO registers
- */
-#define OMAP1510_GPIO_BASE 0xfffce000
-#define OMAP1510_GPIO_DATA_INPUT 0x00
-#define OMAP1510_GPIO_DATA_OUTPUT 0x04
-#define OMAP1510_GPIO_DIR_CONTROL 0x08
-#define OMAP1510_GPIO_INT_CONTROL 0x0c
-#define OMAP1510_GPIO_INT_MASK 0x10
-#define OMAP1510_GPIO_INT_STATUS 0x14
-#define OMAP1510_GPIO_PIN_CONTROL 0x18
-
-#define OMAP1510_IH_GPIO_BASE 64
-
-/*
- * OMAP1610 specific GPIO registers
- */
-#define OMAP1610_GPIO1_BASE 0xfffbe400
-#define OMAP1610_GPIO2_BASE 0xfffbec00
-#define OMAP1610_GPIO3_BASE 0xfffbb400
-#define OMAP1610_GPIO4_BASE 0xfffbbc00
-#define OMAP1610_GPIO_REVISION 0x0000
-#define OMAP1610_GPIO_SYSCONFIG 0x0010
-#define OMAP1610_GPIO_SYSSTATUS 0x0014
-#define OMAP1610_GPIO_IRQSTATUS1 0x0018
-#define OMAP1610_GPIO_IRQENABLE1 0x001c
-#define OMAP1610_GPIO_DATAIN 0x002c
-#define OMAP1610_GPIO_DATAOUT 0x0030
-#define OMAP1610_GPIO_DIRECTION 0x0034
-#define OMAP1610_GPIO_EDGE_CTRL1 0x0038
-#define OMAP1610_GPIO_EDGE_CTRL2 0x003c
-#define OMAP1610_GPIO_CLEAR_IRQENABLE1 0x009c
-#define OMAP1610_GPIO_CLEAR_DATAOUT 0x00b0
-#define OMAP1610_GPIO_SET_IRQENABLE1 0x00dc
-#define OMAP1610_GPIO_SET_DATAOUT 0x00f0
-
-/*
- * OMAP730 specific GPIO registers
- */
-#define OMAP730_GPIO1_BASE 0xfffbc000
-#define OMAP730_GPIO2_BASE 0xfffbc800
-#define OMAP730_GPIO3_BASE 0xfffbd000
-#define OMAP730_GPIO4_BASE 0xfffbd800
-#define OMAP730_GPIO5_BASE 0xfffbe000
-#define OMAP730_GPIO6_BASE 0xfffbe800
-#define OMAP730_GPIO_DATA_INPUT 0x00
-#define OMAP730_GPIO_DATA_OUTPUT 0x04
-#define OMAP730_GPIO_DIR_CONTROL 0x08
-#define OMAP730_GPIO_INT_CONTROL 0x0c
-#define OMAP730_GPIO_INT_MASK 0x10
-#define OMAP730_GPIO_INT_STATUS 0x14
-
-#define OMAP_MPUIO_MASK (~OMAP_MAX_GPIO_LINES & 0xff)
-
-struct gpio_bank {
- u32 base;
- u16 irq;
- u16 virtual_irq_start;
- u8 method;
- u32 reserved_map;
- spinlock_t lock;
-};
-
-#define METHOD_MPUIO 0
-#define METHOD_GPIO_1510 1
-#define METHOD_GPIO_1610 2
-#define METHOD_GPIO_730 3
-
-#if defined(CONFIG_ARCH_OMAP16XX)
-static struct gpio_bank gpio_bank_1610[5] = {
- { OMAP_MPUIO_BASE, INT_MPUIO, IH_MPUIO_BASE, METHOD_MPUIO},
- { OMAP1610_GPIO1_BASE, INT_GPIO_BANK1, IH_GPIO_BASE, METHOD_GPIO_1610 },
- { OMAP1610_GPIO2_BASE, INT_1610_GPIO_BANK2, IH_GPIO_BASE + 16, METHOD_GPIO_1610 },
- { OMAP1610_GPIO3_BASE, INT_1610_GPIO_BANK3, IH_GPIO_BASE + 32, METHOD_GPIO_1610 },
- { OMAP1610_GPIO4_BASE, INT_1610_GPIO_BANK4, IH_GPIO_BASE + 48, METHOD_GPIO_1610 },
-};
-#endif
-
-#ifdef CONFIG_ARCH_OMAP1510
-static struct gpio_bank gpio_bank_1510[2] = {
- { OMAP_MPUIO_BASE, INT_MPUIO, IH_MPUIO_BASE, METHOD_MPUIO },
- { OMAP1510_GPIO_BASE, INT_GPIO_BANK1, IH_GPIO_BASE, METHOD_GPIO_1510 }
-};
-#endif
-
-#ifdef CONFIG_ARCH_OMAP730
-static struct gpio_bank gpio_bank_730[7] = {
- { OMAP_MPUIO_BASE, INT_730_MPUIO, IH_MPUIO_BASE, METHOD_MPUIO },
- { OMAP730_GPIO1_BASE, INT_730_GPIO_BANK1, IH_GPIO_BASE, METHOD_GPIO_730 },
- { OMAP730_GPIO2_BASE, INT_730_GPIO_BANK2, IH_GPIO_BASE + 32, METHOD_GPIO_730 },
- { OMAP730_GPIO3_BASE, INT_730_GPIO_BANK3, IH_GPIO_BASE + 64, METHOD_GPIO_730 },
- { OMAP730_GPIO4_BASE, INT_730_GPIO_BANK4, IH_GPIO_BASE + 96, METHOD_GPIO_730 },
- { OMAP730_GPIO5_BASE, INT_730_GPIO_BANK5, IH_GPIO_BASE + 128, METHOD_GPIO_730 },
- { OMAP730_GPIO6_BASE, INT_730_GPIO_BANK6, IH_GPIO_BASE + 160, METHOD_GPIO_730 },
-};
-#endif
-
-static struct gpio_bank *gpio_bank;
-static int gpio_bank_count;
-
-static inline struct gpio_bank *get_gpio_bank(int gpio)
-{
-#ifdef CONFIG_ARCH_OMAP1510
- if (cpu_is_omap1510()) {
- if (OMAP_GPIO_IS_MPUIO(gpio))
- return &gpio_bank[0];
- return &gpio_bank[1];
- }
-#endif
-#if defined(CONFIG_ARCH_OMAP16XX)
- if (cpu_is_omap16xx()) {
- if (OMAP_GPIO_IS_MPUIO(gpio))
- return &gpio_bank[0];
- return &gpio_bank[1 + (gpio >> 4)];
- }
-#endif
-#ifdef CONFIG_ARCH_OMAP730
- if (cpu_is_omap730()) {
- if (OMAP_GPIO_IS_MPUIO(gpio))
- return &gpio_bank[0];
- return &gpio_bank[1 + (gpio >> 5)];
- }
-#endif
-}
-
-static inline int get_gpio_index(int gpio)
-{
- if (cpu_is_omap730())
- return gpio & 0x1f;
- else
- return gpio & 0x0f;
-}
-
-static inline int gpio_valid(int gpio)
-{
- if (gpio < 0)
- return -1;
- if (OMAP_GPIO_IS_MPUIO(gpio)) {
- if ((gpio & OMAP_MPUIO_MASK) > 16)
- return -1;
- return 0;
- }
-#ifdef CONFIG_ARCH_OMAP1510
- if (cpu_is_omap1510() && gpio < 16)
- return 0;
-#endif
-#if defined(CONFIG_ARCH_OMAP16XX)
- if ((cpu_is_omap16xx()) && gpio < 64)
- return 0;
-#endif
-#ifdef CONFIG_ARCH_OMAP730
- if (cpu_is_omap730() && gpio < 192)
- return 0;
-#endif
- return -1;
-}
-
-static int check_gpio(int gpio)
-{
- if (unlikely(gpio_valid(gpio)) < 0) {
- printk(KERN_ERR "omap-gpio: invalid GPIO %d\n", gpio);
- dump_stack();
- return -1;
- }
- return 0;
-}
-
-static void _set_gpio_direction(struct gpio_bank *bank, int gpio, int is_input)
-{
- u32 reg = bank->base;
- u32 l;
-
- switch (bank->method) {
- case METHOD_MPUIO:
- reg += OMAP_MPUIO_IO_CNTL;
- break;
- case METHOD_GPIO_1510:
- reg += OMAP1510_GPIO_DIR_CONTROL;
- break;
- case METHOD_GPIO_1610:
- reg += OMAP1610_GPIO_DIRECTION;
- break;
- case METHOD_GPIO_730:
- reg += OMAP730_GPIO_DIR_CONTROL;
- break;
- }
- l = __raw_readl(reg);
- if (is_input)
- l |= 1 << gpio;
- else
- l &= ~(1 << gpio);
- __raw_writel(l, reg);
-}
-
-void omap_set_gpio_direction(int gpio, int is_input)
-{
- struct gpio_bank *bank;
-
- if (check_gpio(gpio) < 0)
- return;
- bank = get_gpio_bank(gpio);
- spin_lock(&bank->lock);
- _set_gpio_direction(bank, get_gpio_index(gpio), is_input);
- spin_unlock(&bank->lock);
-}
-
-static void _set_gpio_dataout(struct gpio_bank *bank, int gpio, int enable)
-{
- u32 reg = bank->base;
- u32 l = 0;
-
- switch (bank->method) {
- case METHOD_MPUIO:
- reg += OMAP_MPUIO_OUTPUT;
- l = __raw_readl(reg);
- if (enable)
- l |= 1 << gpio;
- else
- l &= ~(1 << gpio);
- break;
- case METHOD_GPIO_1510:
- reg += OMAP1510_GPIO_DATA_OUTPUT;
- l = __raw_readl(reg);
- if (enable)
- l |= 1 << gpio;
- else
- l &= ~(1 << gpio);
- break;
- case METHOD_GPIO_1610:
- if (enable)
- reg += OMAP1610_GPIO_SET_DATAOUT;
- else
- reg += OMAP1610_GPIO_CLEAR_DATAOUT;
- l = 1 << gpio;
- break;
- case METHOD_GPIO_730:
- reg += OMAP730_GPIO_DATA_OUTPUT;
- l = __raw_readl(reg);
- if (enable)
- l |= 1 << gpio;
- else
- l &= ~(1 << gpio);
- break;
- default:
- BUG();
- return;
- }
- __raw_writel(l, reg);
-}
-
-void omap_set_gpio_dataout(int gpio, int enable)
-{
- struct gpio_bank *bank;
-
- if (check_gpio(gpio) < 0)
- return;
- bank = get_gpio_bank(gpio);
- spin_lock(&bank->lock);
- _set_gpio_dataout(bank, get_gpio_index(gpio), enable);
- spin_unlock(&bank->lock);
-}
-
-int omap_get_gpio_datain(int gpio)
-{
- struct gpio_bank *bank;
- u32 reg;
-
- if (check_gpio(gpio) < 0)
- return -1;
- bank = get_gpio_bank(gpio);
- reg = bank->base;
- switch (bank->method) {
- case METHOD_MPUIO:
- reg += OMAP_MPUIO_INPUT_LATCH;
- break;
- case METHOD_GPIO_1510:
- reg += OMAP1510_GPIO_DATA_INPUT;
- break;
- case METHOD_GPIO_1610:
- reg += OMAP1610_GPIO_DATAIN;
- break;
- case METHOD_GPIO_730:
- reg += OMAP730_GPIO_DATA_INPUT;
- break;
- default:
- BUG();
- return -1;
- }
- return (__raw_readl(reg) & (1 << get_gpio_index(gpio))) != 0;
-}
-
-static void _set_gpio_edge_ctrl(struct gpio_bank *bank, int gpio, int edge)
-{
- u32 reg = bank->base;
- u32 l;
-
- switch (bank->method) {
- case METHOD_MPUIO:
- reg += OMAP_MPUIO_GPIO_INT_EDGE;
- l = __raw_readl(reg);
- if (edge == OMAP_GPIO_RISING_EDGE)
- l |= 1 << gpio;
- else
- l &= ~(1 << gpio);
- __raw_writel(l, reg);
- break;
- case METHOD_GPIO_1510:
- reg += OMAP1510_GPIO_INT_CONTROL;
- l = __raw_readl(reg);
- if (edge == OMAP_GPIO_RISING_EDGE)
- l |= 1 << gpio;
- else
- l &= ~(1 << gpio);
- __raw_writel(l, reg);
- break;
- case METHOD_GPIO_1610:
- edge &= 0x03;
- if (gpio & 0x08)
- reg += OMAP1610_GPIO_EDGE_CTRL2;
- else
- reg += OMAP1610_GPIO_EDGE_CTRL1;
- gpio &= 0x07;
- l = __raw_readl(reg);
- l &= ~(3 << (gpio << 1));
- l |= edge << (gpio << 1);
- __raw_writel(l, reg);
- break;
- case METHOD_GPIO_730:
- reg += OMAP730_GPIO_INT_CONTROL;
- l = __raw_readl(reg);
- if (edge == OMAP_GPIO_RISING_EDGE)
- l |= 1 << gpio;
- else
- l &= ~(1 << gpio);
- __raw_writel(l, reg);
- break;
- default:
- BUG();
- return;
- }
-}
-
-void omap_set_gpio_edge_ctrl(int gpio, int edge)
-{
- struct gpio_bank *bank;
-
- if (check_gpio(gpio) < 0)
- return;
- bank = get_gpio_bank(gpio);
- spin_lock(&bank->lock);
- _set_gpio_edge_ctrl(bank, get_gpio_index(gpio), edge);
- spin_unlock(&bank->lock);
-}
-
-
-static int _get_gpio_edge_ctrl(struct gpio_bank *bank, int gpio)
-{
- u32 reg = bank->base, l;
-
- switch (bank->method) {
- case METHOD_MPUIO:
- l = __raw_readl(reg + OMAP_MPUIO_GPIO_INT_EDGE);
- return (l & (1 << gpio)) ?
- OMAP_GPIO_RISING_EDGE : OMAP_GPIO_FALLING_EDGE;
- case METHOD_GPIO_1510:
- l = __raw_readl(reg + OMAP1510_GPIO_INT_CONTROL);
- return (l & (1 << gpio)) ?
- OMAP_GPIO_RISING_EDGE : OMAP_GPIO_FALLING_EDGE;
- case METHOD_GPIO_1610:
- if (gpio & 0x08)
- reg += OMAP1610_GPIO_EDGE_CTRL2;
- else
- reg += OMAP1610_GPIO_EDGE_CTRL1;
- return (__raw_readl(reg) >> ((gpio & 0x07) << 1)) & 0x03;
- case METHOD_GPIO_730:
- l = __raw_readl(reg + OMAP730_GPIO_INT_CONTROL);
- return (l & (1 << gpio)) ?
- OMAP_GPIO_RISING_EDGE : OMAP_GPIO_FALLING_EDGE;
- default:
- BUG();
- return -1;
- }
-}
-
-static void _clear_gpio_irqbank(struct gpio_bank *bank, int gpio_mask)
-{
- u32 reg = bank->base;
-
- switch (bank->method) {
- case METHOD_MPUIO:
- /* MPUIO irqstatus is reset by reading the status register,
- * so do nothing here */
- return;
- case METHOD_GPIO_1510:
- reg += OMAP1510_GPIO_INT_STATUS;
- break;
- case METHOD_GPIO_1610:
- reg += OMAP1610_GPIO_IRQSTATUS1;
- break;
- case METHOD_GPIO_730:
- reg += OMAP730_GPIO_INT_STATUS;
- break;
- default:
- BUG();
- return;
- }
- __raw_writel(gpio_mask, reg);
-}
-
-static inline void _clear_gpio_irqstatus(struct gpio_bank *bank, int gpio)
-{
- _clear_gpio_irqbank(bank, 1 << get_gpio_index(gpio));
-}
-
-static void _enable_gpio_irqbank(struct gpio_bank *bank, int gpio_mask, int enable)
-{
- u32 reg = bank->base;
- u32 l;
-
- switch (bank->method) {
- case METHOD_MPUIO:
- reg += OMAP_MPUIO_GPIO_MASKIT;
- l = __raw_readl(reg);
- if (enable)
- l &= ~(gpio_mask);
- else
- l |= gpio_mask;
- break;
- case METHOD_GPIO_1510:
- reg += OMAP1510_GPIO_INT_MASK;
- l = __raw_readl(reg);
- if (enable)
- l &= ~(gpio_mask);
- else
- l |= gpio_mask;
- break;
- case METHOD_GPIO_1610:
- if (enable)
- reg += OMAP1610_GPIO_SET_IRQENABLE1;
- else
- reg += OMAP1610_GPIO_CLEAR_IRQENABLE1;
- l = gpio_mask;
- break;
- case METHOD_GPIO_730:
- reg += OMAP730_GPIO_INT_MASK;
- l = __raw_readl(reg);
- if (enable)
- l &= ~(gpio_mask);
- else
- l |= gpio_mask;
- break;
- default:
- BUG();
- return;
- }
- __raw_writel(l, reg);
-}
-
-static inline void _set_gpio_irqenable(struct gpio_bank *bank, int gpio, int enable)
-{
- _enable_gpio_irqbank(bank, 1 << get_gpio_index(gpio), enable);
-}
-
-int omap_request_gpio(int gpio)
-{
- struct gpio_bank *bank;
-
- if (check_gpio(gpio) < 0)
- return -EINVAL;
-
- bank = get_gpio_bank(gpio);
- spin_lock(&bank->lock);
- if (unlikely(bank->reserved_map & (1 << get_gpio_index(gpio)))) {
- printk(KERN_ERR "omap-gpio: GPIO %d is already reserved!\n", gpio);
- dump_stack();
- spin_unlock(&bank->lock);
- return -1;
- }
- bank->reserved_map |= (1 << get_gpio_index(gpio));
-#ifdef CONFIG_ARCH_OMAP1510
- if (bank->method == METHOD_GPIO_1510) {
- u32 reg;
-
- /* Claim the pin for the ARM */
- reg = bank->base + OMAP1510_GPIO_PIN_CONTROL;
- __raw_writel(__raw_readl(reg) | (1 << get_gpio_index(gpio)), reg);
- }
-#endif
- spin_unlock(&bank->lock);
-
- return 0;
-}
-
-void omap_free_gpio(int gpio)
-{
- struct gpio_bank *bank;
-
- if (check_gpio(gpio) < 0)
- return;
- bank = get_gpio_bank(gpio);
- spin_lock(&bank->lock);
- if (unlikely(!(bank->reserved_map & (1 << get_gpio_index(gpio))))) {
- printk(KERN_ERR "omap-gpio: GPIO %d wasn't reserved!\n", gpio);
- dump_stack();
- spin_unlock(&bank->lock);
- return;
- }
- bank->reserved_map &= ~(1 << get_gpio_index(gpio));
- _set_gpio_direction(bank, get_gpio_index(gpio), 1);
- _set_gpio_irqenable(bank, gpio, 0);
- _clear_gpio_irqstatus(bank, gpio);
- spin_unlock(&bank->lock);
-}
-
-/*
- * We need to unmask the GPIO bank interrupt as soon as possible to
- * avoid missing GPIO interrupts for other lines in the bank.
- * Then we need to mask-read-clear-unmask the triggered GPIO lines
- * in the bank to avoid missing nested interrupts for a GPIO line.
- * If we wait to unmask individual GPIO lines in the bank after the
- * line's interrupt handler has been run, we may miss some nested
- * interrupts.
- */
-static void gpio_irq_handler(unsigned int irq, struct irqdesc *desc,
- struct pt_regs *regs)
-{
- u32 isr_reg = 0;
- u32 isr;
- unsigned int gpio_irq;
- struct gpio_bank *bank;
-
- desc->chip->ack(irq);
-
- bank = (struct gpio_bank *) desc->data;
- if (bank->method == METHOD_MPUIO)
- isr_reg = bank->base + OMAP_MPUIO_GPIO_INT;
-#ifdef CONFIG_ARCH_OMAP1510
- if (bank->method == METHOD_GPIO_1510)
- isr_reg = bank->base + OMAP1510_GPIO_INT_STATUS;
-#endif
-#if defined(CONFIG_ARCH_OMAP16XX)
- if (bank->method == METHOD_GPIO_1610)
- isr_reg = bank->base + OMAP1610_GPIO_IRQSTATUS1;
-#endif
-#ifdef CONFIG_ARCH_OMAP730
- if (bank->method == METHOD_GPIO_730)
- isr_reg = bank->base + OMAP730_GPIO_INT_STATUS;
-#endif
-
- isr = __raw_readl(isr_reg);
- _enable_gpio_irqbank(bank, isr, 0);
- _clear_gpio_irqbank(bank, isr);
- _enable_gpio_irqbank(bank, isr, 1);
- desc->chip->unmask(irq);
-
- if (unlikely(!isr))
- return;
-
- gpio_irq = bank->virtual_irq_start;
- for (; isr != 0; isr >>= 1, gpio_irq++) {
- struct irqdesc *d;
- if (!(isr & 1))
- continue;
- d = irq_desc + gpio_irq;
- d->handle(gpio_irq, d, regs);
- }
-}
-
-static void gpio_ack_irq(unsigned int irq)
-{
- unsigned int gpio = irq - IH_GPIO_BASE;
- struct gpio_bank *bank = get_gpio_bank(gpio);
-
- _clear_gpio_irqstatus(bank, gpio);
-}
-
-static void gpio_mask_irq(unsigned int irq)
-{
- unsigned int gpio = irq - IH_GPIO_BASE;
- struct gpio_bank *bank = get_gpio_bank(gpio);
-
- _set_gpio_irqenable(bank, gpio, 0);
-}
-
-static void gpio_unmask_irq(unsigned int irq)
-{
- unsigned int gpio = irq - IH_GPIO_BASE;
- struct gpio_bank *bank = get_gpio_bank(gpio);
-
- if (_get_gpio_edge_ctrl(bank, get_gpio_index(gpio)) == OMAP_GPIO_NO_EDGE) {
- printk(KERN_ERR "OMAP GPIO %d: trying to enable GPIO IRQ while no edge is set\n",
- gpio);
- _set_gpio_edge_ctrl(bank, get_gpio_index(gpio), OMAP_GPIO_RISING_EDGE);
- }
- _set_gpio_irqenable(bank, gpio, 1);
-}
-
-static void mpuio_ack_irq(unsigned int irq)
-{
- /* The ISR is reset automatically, so do nothing here. */
-}
-
-static void mpuio_mask_irq(unsigned int irq)
-{
- unsigned int gpio = OMAP_MPUIO(irq - IH_MPUIO_BASE);
- struct gpio_bank *bank = get_gpio_bank(gpio);
-
- _set_gpio_irqenable(bank, gpio, 0);
-}
-
-static void mpuio_unmask_irq(unsigned int irq)
-{
- unsigned int gpio = OMAP_MPUIO(irq - IH_MPUIO_BASE);
- struct gpio_bank *bank = get_gpio_bank(gpio);
-
- _set_gpio_irqenable(bank, gpio, 1);
-}
-
-static struct irqchip gpio_irq_chip = {
- .ack = gpio_ack_irq,
- .mask = gpio_mask_irq,
- .unmask = gpio_unmask_irq,
-};
-
-static struct irqchip mpuio_irq_chip = {
- .ack = mpuio_ack_irq,
- .mask = mpuio_mask_irq,
- .unmask = mpuio_unmask_irq
-};
-
-static int initialized = 0;
-
-static int __init _omap_gpio_init(void)
-{
- int i;
- struct gpio_bank *bank;
-
- initialized = 1;
-
-#ifdef CONFIG_ARCH_OMAP1510
- if (cpu_is_omap1510()) {
- printk(KERN_INFO "OMAP1510 GPIO hardware\n");
- gpio_bank_count = 2;
- gpio_bank = gpio_bank_1510;
- }
-#endif
-#if defined(CONFIG_ARCH_OMAP16XX)
- if (cpu_is_omap16xx()) {
- int rev;
-
- gpio_bank_count = 5;
- gpio_bank = gpio_bank_1610;
- rev = omap_readw(gpio_bank[1].base + OMAP1610_GPIO_REVISION);
- printk(KERN_INFO "OMAP GPIO hardware version %d.%d\n",
- (rev >> 4) & 0x0f, rev & 0x0f);
- }
-#endif
-#ifdef CONFIG_ARCH_OMAP730
- if (cpu_is_omap730()) {
- printk(KERN_INFO "OMAP730 GPIO hardware\n");
- gpio_bank_count = 7;
- gpio_bank = gpio_bank_730;
- }
-#endif
- for (i = 0; i < gpio_bank_count; i++) {
- int j, gpio_count = 16;
-
- bank = &gpio_bank[i];
- bank->reserved_map = 0;
- bank->base = IO_ADDRESS(bank->base);
- spin_lock_init(&bank->lock);
- if (bank->method == METHOD_MPUIO) {
- omap_writew(0xFFFF, OMAP_MPUIO_BASE + OMAP_MPUIO_GPIO_MASKIT);
- }
-#ifdef CONFIG_ARCH_OMAP1510
- if (bank->method == METHOD_GPIO_1510) {
- __raw_writew(0xffff, bank->base + OMAP1510_GPIO_INT_MASK);
- __raw_writew(0x0000, bank->base + OMAP1510_GPIO_INT_STATUS);
- }
-#endif
-#if defined(CONFIG_ARCH_OMAP16XX)
- if (bank->method == METHOD_GPIO_1610) {
- __raw_writew(0x0000, bank->base + OMAP1610_GPIO_IRQENABLE1);
- __raw_writew(0xffff, bank->base + OMAP1610_GPIO_IRQSTATUS1);
- }
-#endif
-#ifdef CONFIG_ARCH_OMAP730
- if (bank->method == METHOD_GPIO_730) {
- __raw_writel(0xffffffff, bank->base + OMAP730_GPIO_INT_MASK);
- __raw_writel(0x00000000, bank->base + OMAP730_GPIO_INT_STATUS);
-
- gpio_count = 32; /* 730 has 32-bit GPIOs */
- }
-#endif
- for (j = bank->virtual_irq_start;
- j < bank->virtual_irq_start + gpio_count; j++) {
- if (bank->method == METHOD_MPUIO)
- set_irq_chip(j, &mpuio_irq_chip);
- else
- set_irq_chip(j, &gpio_irq_chip);
- set_irq_handler(j, do_simple_IRQ);
- set_irq_flags(j, IRQF_VALID);
- }
- set_irq_chained_handler(bank->irq, gpio_irq_handler);
- set_irq_data(bank->irq, bank);
- }
-
- /* Enable system clock for GPIO module.
- * The CAM_CLK_CTRL *is* really the right place. */
- if (cpu_is_omap1610() || cpu_is_omap1710())
- omap_writel(omap_readl(ULPD_CAM_CLK_CTRL) | 0x04, ULPD_CAM_CLK_CTRL);
-
- return 0;
-}
-
-/*
- * This may get called early from board specific init
- */
-int omap_gpio_init(void)
-{
- if (!initialized)
- return _omap_gpio_init();
- else
- return 0;
-}
-
-EXPORT_SYMBOL(omap_request_gpio);
-EXPORT_SYMBOL(omap_free_gpio);
-EXPORT_SYMBOL(omap_set_gpio_direction);
-EXPORT_SYMBOL(omap_set_gpio_dataout);
-EXPORT_SYMBOL(omap_get_gpio_datain);
-EXPORT_SYMBOL(omap_set_gpio_edge_ctrl);
-
-arch_initcall(omap_gpio_init);
+++ /dev/null
-/*
- * linux/arch/arm/omap/mcbsp.c
- *
- * Copyright (C) 2004 Nokia Corporation
- * Author: Samuel Ortiz <samuel.ortiz@nokia.com>
- *
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * Multichannel mode not supported.
- */
-
-#include <linux/module.h>
-#include <linux/init.h>
-#include <linux/device.h>
-#include <linux/wait.h>
-#include <linux/completion.h>
-#include <linux/interrupt.h>
-#include <linux/err.h>
-
-#include <asm/delay.h>
-#include <asm/io.h>
-#include <asm/irq.h>
-
-#include <asm/arch/dma.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/irqs.h>
-#include <asm/arch/mcbsp.h>
-
-#include <asm/hardware/clock.h>
-
-#ifdef CONFIG_MCBSP_DEBUG
-#define DBG(x...) printk(x)
-#else
-#define DBG(x...) do { } while (0)
-#endif
-
-struct omap_mcbsp {
- u32 io_base;
- u8 id;
- u8 free;
- omap_mcbsp_word_length rx_word_length;
- omap_mcbsp_word_length tx_word_length;
-
- /* IRQ based TX/RX */
- int rx_irq;
- int tx_irq;
-
- /* DMA stuff */
- u8 dma_rx_sync;
- short dma_rx_lch;
- u8 dma_tx_sync;
- short dma_tx_lch;
-
- /* Completion queues */
- struct completion tx_irq_completion;
- struct completion rx_irq_completion;
- struct completion tx_dma_completion;
- struct completion rx_dma_completion;
-
- spinlock_t lock;
-};
-
-static struct omap_mcbsp mcbsp[OMAP_MAX_MCBSP_COUNT];
-static struct clk *mcbsp_dsp_ck = 0;
-static struct clk *mcbsp_api_ck = 0;
-
-
-static void omap_mcbsp_dump_reg(u8 id)
-{
- DBG("**** MCBSP%d regs ****\n", mcbsp[id].id);
- DBG("DRR2: 0x%04x\n", OMAP_MCBSP_READ(mcbsp[id].io_base, DRR2));
- DBG("DRR1: 0x%04x\n", OMAP_MCBSP_READ(mcbsp[id].io_base, DRR1));
- DBG("DXR2: 0x%04x\n", OMAP_MCBSP_READ(mcbsp[id].io_base, DXR2));
- DBG("DXR1: 0x%04x\n", OMAP_MCBSP_READ(mcbsp[id].io_base, DXR1));
- DBG("SPCR2: 0x%04x\n", OMAP_MCBSP_READ(mcbsp[id].io_base, SPCR2));
- DBG("SPCR1: 0x%04x\n", OMAP_MCBSP_READ(mcbsp[id].io_base, SPCR1));
- DBG("RCR2: 0x%04x\n", OMAP_MCBSP_READ(mcbsp[id].io_base, RCR2));
- DBG("RCR1: 0x%04x\n", OMAP_MCBSP_READ(mcbsp[id].io_base, RCR1));
- DBG("XCR2: 0x%04x\n", OMAP_MCBSP_READ(mcbsp[id].io_base, XCR2));
- DBG("XCR1: 0x%04x\n", OMAP_MCBSP_READ(mcbsp[id].io_base, XCR1));
- DBG("SRGR2: 0x%04x\n", OMAP_MCBSP_READ(mcbsp[id].io_base, SRGR2));
- DBG("SRGR1: 0x%04x\n", OMAP_MCBSP_READ(mcbsp[id].io_base, SRGR1));
- DBG("PCR0: 0x%04x\n", OMAP_MCBSP_READ(mcbsp[id].io_base, PCR0));
- DBG("***********************\n");
-}
-
-
-static irqreturn_t omap_mcbsp_tx_irq_handler(int irq, void *dev_id, struct pt_regs *regs)
-{
- struct omap_mcbsp * mcbsp_tx = (struct omap_mcbsp *)(dev_id);
-
- DBG("TX IRQ callback : 0x%x\n", OMAP_MCBSP_READ(mcbsp_tx->io_base, SPCR2));
-
- complete(&mcbsp_tx->tx_irq_completion);
- return IRQ_HANDLED;
-}
-
-static irqreturn_t omap_mcbsp_rx_irq_handler(int irq, void *dev_id, struct pt_regs *regs)
-{
- struct omap_mcbsp * mcbsp_rx = (struct omap_mcbsp *)(dev_id);
-
- DBG("RX IRQ callback : 0x%x\n", OMAP_MCBSP_READ(mcbsp_rx->io_base, SPCR2));
-
- complete(&mcbsp_rx->rx_irq_completion);
- return IRQ_HANDLED;
-}
-
-
-static void omap_mcbsp_tx_dma_callback(int lch, u16 ch_status, void *data)
-{
- struct omap_mcbsp * mcbsp_dma_tx = (struct omap_mcbsp *)(data);
-
- DBG("TX DMA callback : 0x%x\n", OMAP_MCBSP_READ(mcbsp_dma_tx->io_base, SPCR2));
-
- /* We can free the channels */
- omap_free_dma(mcbsp_dma_tx->dma_tx_lch);
- mcbsp_dma_tx->dma_tx_lch = -1;
-
- complete(&mcbsp_dma_tx->tx_dma_completion);
-}
-
-static void omap_mcbsp_rx_dma_callback(int lch, u16 ch_status, void *data)
-{
- struct omap_mcbsp * mcbsp_dma_rx = (struct omap_mcbsp *)(data);
-
- DBG("RX DMA callback : 0x%x\n", OMAP_MCBSP_READ(mcbsp_dma_rx->io_base, SPCR2));
-
- /* We can free the channels */
- omap_free_dma(mcbsp_dma_rx->dma_rx_lch);
- mcbsp_dma_rx->dma_rx_lch = -1;
-
- complete(&mcbsp_dma_rx->rx_dma_completion);
-}
-
-
-/*
- * omap_mcbsp_config simply write a config to the
- * appropriate McBSP.
- * You either call this function or set the McBSP registers
- * by yourself before calling omap_mcbsp_start().
- */
-
-void omap_mcbsp_config(unsigned int id, const struct omap_mcbsp_reg_cfg * config)
-{
- u32 io_base = mcbsp[id].io_base;
-
- DBG("OMAP-McBSP: McBSP%d io_base: 0x%8x\n", id+1, io_base);
-
- /* We write the given config */
- OMAP_MCBSP_WRITE(io_base, SPCR2, config->spcr2);
- OMAP_MCBSP_WRITE(io_base, SPCR1, config->spcr1);
- OMAP_MCBSP_WRITE(io_base, RCR2, config->rcr2);
- OMAP_MCBSP_WRITE(io_base, RCR1, config->rcr1);
- OMAP_MCBSP_WRITE(io_base, XCR2, config->xcr2);
- OMAP_MCBSP_WRITE(io_base, XCR1, config->xcr1);
- OMAP_MCBSP_WRITE(io_base, SRGR2, config->srgr2);
- OMAP_MCBSP_WRITE(io_base, SRGR1, config->srgr1);
- OMAP_MCBSP_WRITE(io_base, MCR2, config->mcr2);
- OMAP_MCBSP_WRITE(io_base, MCR1, config->mcr1);
- OMAP_MCBSP_WRITE(io_base, PCR0, config->pcr0);
-}
-
-
-
-static int omap_mcbsp_check(unsigned int id)
-{
- if (cpu_is_omap730()) {
- if (id > OMAP_MAX_MCBSP_COUNT - 1) {
- printk(KERN_ERR "OMAP-McBSP: McBSP%d doesn't exist\n", id + 1);
- return -1;
- }
- return 0;
- }
-
- if (cpu_is_omap1510() || cpu_is_omap1610() || cpu_is_omap1710()) {
- if (id > OMAP_MAX_MCBSP_COUNT) {
- printk(KERN_ERR "OMAP-McBSP: McBSP%d doesn't exist\n", id + 1);
- return -1;
- }
- return 0;
- }
-
- return -1;
-}
-
-#define EN_XORPCK 1
-#define DSP_RSTCT2 0xe1008014
-
-static void omap_mcbsp_dsp_request(void)
-{
- if (cpu_is_omap1510() || cpu_is_omap1610() || cpu_is_omap1710()) {
- omap_writew((omap_readw(ARM_RSTCT1) | (1 << 1) | (1 << 2)),
- ARM_RSTCT1);
- clk_enable(mcbsp_dsp_ck);
- clk_enable(mcbsp_api_ck);
-
- /* enable 12MHz clock to mcbsp 1 & 3 */
- __raw_writew(__raw_readw(DSP_IDLECT2) | (1 << EN_XORPCK),
- DSP_IDLECT2);
- __raw_writew(__raw_readw(DSP_RSTCT2) | 1 | 1 << 1,
- DSP_RSTCT2);
- }
-}
-
-static void omap_mcbsp_dsp_free(void)
-{
- /* Useless for now */
-}
-
-
-int omap_mcbsp_request(unsigned int id)
-{
- int err;
-
- if (omap_mcbsp_check(id) < 0)
- return -EINVAL;
-
- /*
- * On 1510, 1610 and 1710, McBSP1 and McBSP3
- * are DSP public peripherals.
- */
- if (id == OMAP_MCBSP1 || id == OMAP_MCBSP3)
- omap_mcbsp_dsp_request();
-
- spin_lock(&mcbsp[id].lock);
- if (!mcbsp[id].free) {
- printk (KERN_ERR "OMAP-McBSP: McBSP%d is currently in use\n", id + 1);
- spin_unlock(&mcbsp[id].lock);
- return -1;
- }
-
- mcbsp[id].free = 0;
- spin_unlock(&mcbsp[id].lock);
-
- /* We need to get IRQs here */
- err = request_irq(mcbsp[id].tx_irq, omap_mcbsp_tx_irq_handler, 0,
- "McBSP",
- (void *) (&mcbsp[id]));
- if (err != 0) {
- printk(KERN_ERR "OMAP-McBSP: Unable to request TX IRQ %d for McBSP%d\n",
- mcbsp[id].tx_irq, mcbsp[id].id);
- return err;
- }
-
- init_completion(&(mcbsp[id].tx_irq_completion));
-
-
- err = request_irq(mcbsp[id].rx_irq, omap_mcbsp_rx_irq_handler, 0,
- "McBSP",
- (void *) (&mcbsp[id]));
- if (err != 0) {
- printk(KERN_ERR "OMAP-McBSP: Unable to request RX IRQ %d for McBSP%d\n",
- mcbsp[id].rx_irq, mcbsp[id].id);
- free_irq(mcbsp[id].tx_irq, (void *) (&mcbsp[id]));
- return err;
- }
-
- init_completion(&(mcbsp[id].rx_irq_completion));
- return 0;
-
-}
-
-void omap_mcbsp_free(unsigned int id)
-{
- if (omap_mcbsp_check(id) < 0)
- return;
-
- if (id == OMAP_MCBSP1 || id == OMAP_MCBSP3)
- omap_mcbsp_dsp_free();
-
- spin_lock(&mcbsp[id].lock);
- if (mcbsp[id].free) {
- printk (KERN_ERR "OMAP-McBSP: McBSP%d was not reserved\n", id + 1);
- spin_unlock(&mcbsp[id].lock);
- return;
- }
-
- mcbsp[id].free = 1;
- spin_unlock(&mcbsp[id].lock);
-
- /* Free IRQs */
- free_irq(mcbsp[id].rx_irq, (void *) (&mcbsp[id]));
- free_irq(mcbsp[id].tx_irq, (void *) (&mcbsp[id]));
-}
-
-/*
- * Here we start the McBSP, by enabling the sample
- * generator, both transmitter and receivers,
- * and the frame sync.
- */
-void omap_mcbsp_start(unsigned int id)
-{
- u32 io_base;
- u16 w;
-
- if (omap_mcbsp_check(id) < 0)
- return;
-
- io_base = mcbsp[id].io_base;
-
- mcbsp[id].rx_word_length = ((OMAP_MCBSP_READ(io_base, RCR1) >> 5) & 0x7);
- mcbsp[id].tx_word_length = ((OMAP_MCBSP_READ(io_base, XCR1) >> 5) & 0x7);
-
- /* Start the sample generator */
- w = OMAP_MCBSP_READ(io_base, SPCR2);
- OMAP_MCBSP_WRITE(io_base, SPCR2, w | (1 << 6));
-
- /* Enable transmitter and receiver */
- w = OMAP_MCBSP_READ(io_base, SPCR2);
- OMAP_MCBSP_WRITE(io_base, SPCR2, w | 1);
-
- w = OMAP_MCBSP_READ(io_base, SPCR1);
- OMAP_MCBSP_WRITE(io_base, SPCR1, w | 1);
-
- udelay(100);
-
- /* Start frame sync */
- w = OMAP_MCBSP_READ(io_base, SPCR2);
- OMAP_MCBSP_WRITE(io_base, SPCR2, w | (1 << 7));
-
- /* Dump McBSP Regs */
- omap_mcbsp_dump_reg(id);
-
-}
-
-void omap_mcbsp_stop(unsigned int id)
-{
- u32 io_base;
- u16 w;
-
- if (omap_mcbsp_check(id) < 0)
- return;
-
- io_base = mcbsp[id].io_base;
-
- /* Reset transmitter */
- w = OMAP_MCBSP_READ(io_base, SPCR2);
- OMAP_MCBSP_WRITE(io_base, SPCR2, w & ~(1));
-
- /* Reset receiver */
- w = OMAP_MCBSP_READ(io_base, SPCR1);
- OMAP_MCBSP_WRITE(io_base, SPCR1, w & ~(1));
-
- /* Reset the sample rate generator */
- w = OMAP_MCBSP_READ(io_base, SPCR2);
- OMAP_MCBSP_WRITE(io_base, SPCR2, w & ~(1 << 6));
-}
-
-
-/*
- * IRQ based word transmission.
- */
-void omap_mcbsp_xmit_word(unsigned int id, u32 word)
-{
- u32 io_base;
- omap_mcbsp_word_length word_length = mcbsp[id].tx_word_length;
-
- if (omap_mcbsp_check(id) < 0)
- return;
-
- io_base = mcbsp[id].io_base;
-
- wait_for_completion(&(mcbsp[id].tx_irq_completion));
-
- if (word_length > OMAP_MCBSP_WORD_16)
- OMAP_MCBSP_WRITE(io_base, DXR2, word >> 16);
- OMAP_MCBSP_WRITE(io_base, DXR1, word & 0xffff);
-}
-
-u32 omap_mcbsp_recv_word(unsigned int id)
-{
- u32 io_base;
- u16 word_lsb, word_msb = 0;
- omap_mcbsp_word_length word_length = mcbsp[id].rx_word_length;
-
- if (omap_mcbsp_check(id) < 0)
- return -EINVAL;
-
- io_base = mcbsp[id].io_base;
-
- wait_for_completion(&(mcbsp[id].rx_irq_completion));
-
- if (word_length > OMAP_MCBSP_WORD_16)
- word_msb = OMAP_MCBSP_READ(io_base, DRR2);
- word_lsb = OMAP_MCBSP_READ(io_base, DRR1);
-
- return (word_lsb | (word_msb << 16));
-}
-
-
-/*
- * Simple DMA based buffer rx/tx routines.
- * Nothing fancy, just a single buffer tx/rx through DMA.
- * The DMA resources are released once the transfer is done.
- * For anything fancier, you should use your own customized DMA
- * routines and callbacks.
- */
-int omap_mcbsp_xmit_buffer(unsigned int id, dma_addr_t buffer, unsigned int length)
-{
- int dma_tx_ch;
-
- if (omap_mcbsp_check(id) < 0)
- return -EINVAL;
-
- if (omap_request_dma(mcbsp[id].dma_tx_sync, "McBSP TX", omap_mcbsp_tx_dma_callback,
- &mcbsp[id],
- &dma_tx_ch)) {
- printk("OMAP-McBSP: Unable to request DMA channel for McBSP%d TX. Trying IRQ based TX\n", id+1);
- return -EAGAIN;
- }
- mcbsp[id].dma_tx_lch = dma_tx_ch;
-
- DBG("TX DMA on channel %d\n", dma_tx_ch);
-
- init_completion(&(mcbsp[id].tx_dma_completion));
-
- omap_set_dma_transfer_params(mcbsp[id].dma_tx_lch,
- OMAP_DMA_DATA_TYPE_S16,
- length >> 1, 1,
- OMAP_DMA_SYNC_ELEMENT);
-
- omap_set_dma_dest_params(mcbsp[id].dma_tx_lch,
- OMAP_DMA_PORT_TIPB,
- OMAP_DMA_AMODE_CONSTANT,
- mcbsp[id].io_base + OMAP_MCBSP_REG_DXR1);
-
- omap_set_dma_src_params(mcbsp[id].dma_tx_lch,
- OMAP_DMA_PORT_EMIFF,
- OMAP_DMA_AMODE_POST_INC,
- buffer);
-
- omap_start_dma(mcbsp[id].dma_tx_lch);
- wait_for_completion(&(mcbsp[id].tx_dma_completion));
- return 0;
-}
-
-
-int omap_mcbsp_recv_buffer(unsigned int id, dma_addr_t buffer, unsigned int length)
-{
- int dma_rx_ch;
-
- if (omap_mcbsp_check(id) < 0)
- return -EINVAL;
-
- if (omap_request_dma(mcbsp[id].dma_rx_sync, "McBSP RX", omap_mcbsp_rx_dma_callback,
- &mcbsp[id],
- &dma_rx_ch)) {
- printk("Unable to request DMA channel for McBSP%d RX. Trying IRQ based RX\n", id+1);
- return -EAGAIN;
- }
- mcbsp[id].dma_rx_lch = dma_rx_ch;
-
- DBG("RX DMA on channel %d\n", dma_rx_ch);
-
- init_completion(&(mcbsp[id].rx_dma_completion));
-
- omap_set_dma_transfer_params(mcbsp[id].dma_rx_lch,
- OMAP_DMA_DATA_TYPE_S16,
- length >> 1, 1,
- OMAP_DMA_SYNC_ELEMENT);
-
- omap_set_dma_src_params(mcbsp[id].dma_rx_lch,
- OMAP_DMA_PORT_TIPB,
- OMAP_DMA_AMODE_CONSTANT,
- mcbsp[id].io_base + OMAP_MCBSP_REG_DRR1);
-
- omap_set_dma_dest_params(mcbsp[id].dma_rx_lch,
- OMAP_DMA_PORT_EMIFF,
- OMAP_DMA_AMODE_POST_INC,
- buffer);
-
- omap_start_dma(mcbsp[id].dma_rx_lch);
- wait_for_completion(&(mcbsp[id].rx_dma_completion));
- return 0;
-}
-
-
-/*
- * SPI wrapper.
- * Since SPI setup is much simpler than the generic McBSP one,
- * this wrapper just need an omap_mcbsp_spi_cfg structure as an input.
- * Once this is done, you can call omap_mcbsp_start().
- */
-void omap_mcbsp_set_spi_mode(unsigned int id, const struct omap_mcbsp_spi_cfg * spi_cfg)
-{
- struct omap_mcbsp_reg_cfg mcbsp_cfg;
-
- if (omap_mcbsp_check(id) < 0)
- return;
-
- memset(&mcbsp_cfg, 0, sizeof(struct omap_mcbsp_reg_cfg));
-
- /* SPI has only one frame */
- mcbsp_cfg.rcr1 |= (RWDLEN1(spi_cfg->word_length) | RFRLEN1(0));
- mcbsp_cfg.xcr1 |= (XWDLEN1(spi_cfg->word_length) | XFRLEN1(0));
-
- /* Clock stop mode */
- if (spi_cfg->clk_stp_mode == OMAP_MCBSP_CLK_STP_MODE_NO_DELAY)
- mcbsp_cfg.spcr1 |= (1 << 12);
- else
- mcbsp_cfg.spcr1 |= (3 << 11);
-
- /* Set clock parities */
- if (spi_cfg->rx_clock_polarity == OMAP_MCBSP_CLK_RISING)
- mcbsp_cfg.pcr0 |= CLKRP;
- else
- mcbsp_cfg.pcr0 &= ~CLKRP;
-
- if (spi_cfg->tx_clock_polarity == OMAP_MCBSP_CLK_RISING)
- mcbsp_cfg.pcr0 &= ~CLKXP;
- else
- mcbsp_cfg.pcr0 |= CLKXP;
-
- /* Set SCLKME to 0 and CLKSM to 1 */
- mcbsp_cfg.pcr0 &= ~SCLKME;
- mcbsp_cfg.srgr2 |= CLKSM;
-
- /* Set FSXP */
- if (spi_cfg->fsx_polarity == OMAP_MCBSP_FS_ACTIVE_HIGH)
- mcbsp_cfg.pcr0 &= ~FSXP;
- else
- mcbsp_cfg.pcr0 |= FSXP;
-
- if (spi_cfg->spi_mode == OMAP_MCBSP_SPI_MASTER) {
- mcbsp_cfg.pcr0 |= CLKXM;
- mcbsp_cfg.srgr1 |= CLKGDV(spi_cfg->clk_div -1);
- mcbsp_cfg.pcr0 |= FSXM;
- mcbsp_cfg.srgr2 &= ~FSGM;
- mcbsp_cfg.xcr2 |= XDATDLY(1);
- mcbsp_cfg.rcr2 |= RDATDLY(1);
- }
- else {
- mcbsp_cfg.pcr0 &= ~CLKXM;
- mcbsp_cfg.srgr1 |= CLKGDV(1);
- mcbsp_cfg.pcr0 &= ~FSXM;
- mcbsp_cfg.xcr2 &= ~XDATDLY(3);
- mcbsp_cfg.rcr2 &= ~RDATDLY(3);
- }
-
- mcbsp_cfg.xcr2 &= ~XPHASE;
- mcbsp_cfg.rcr2 &= ~RPHASE;
-
- omap_mcbsp_config(id, &mcbsp_cfg);
-}
-
-
-/*
- * McBSP1 and McBSP3 are directly mapped on 1610 and 1510.
- * 730 has only 2 McBSP, and both of them are MPU peripherals.
- */
-struct omap_mcbsp_info {
- u32 virt_base;
- u8 dma_rx_sync, dma_tx_sync;
- u16 rx_irq, tx_irq;
-};
-
-#ifdef CONFIG_ARCH_OMAP730
-static const struct omap_mcbsp_info mcbsp_730[] = {
- [0] = { .virt_base = io_p2v(OMAP730_MCBSP1_BASE),
- .dma_rx_sync = OMAP_DMA_MCBSP1_RX,
- .dma_tx_sync = OMAP_DMA_MCBSP1_TX,
- .rx_irq = INT_730_McBSP1RX,
- .tx_irq = INT_730_McBSP1TX },
- [1] = { .virt_base = io_p2v(OMAP730_MCBSP2_BASE),
- .dma_rx_sync = OMAP_DMA_MCBSP3_RX,
- .dma_tx_sync = OMAP_DMA_MCBSP3_TX,
- .rx_irq = INT_730_McBSP2RX,
- .tx_irq = INT_730_McBSP2TX },
-};
-#endif
-
-#ifdef CONFIG_ARCH_OMAP1510
-static const struct omap_mcbsp_info mcbsp_1510[] = {
- [0] = { .virt_base = OMAP1510_MCBSP1_BASE,
- .dma_rx_sync = OMAP_DMA_MCBSP1_RX,
- .dma_tx_sync = OMAP_DMA_MCBSP1_TX,
- .rx_irq = INT_McBSP1RX,
- .tx_irq = INT_McBSP1TX },
- [1] = { .virt_base = io_p2v(OMAP1510_MCBSP2_BASE),
- .dma_rx_sync = OMAP_DMA_MCBSP2_RX,
- .dma_tx_sync = OMAP_DMA_MCBSP2_TX,
- .rx_irq = INT_1510_SPI_RX,
- .tx_irq = INT_1510_SPI_TX },
- [2] = { .virt_base = OMAP1510_MCBSP3_BASE,
- .dma_rx_sync = OMAP_DMA_MCBSP3_RX,
- .dma_tx_sync = OMAP_DMA_MCBSP3_TX,
- .rx_irq = INT_McBSP3RX,
- .tx_irq = INT_McBSP3TX },
-};
-#endif
-
-#if defined(CONFIG_ARCH_OMAP16XX)
-static const struct omap_mcbsp_info mcbsp_1610[] = {
- [0] = { .virt_base = OMAP1610_MCBSP1_BASE,
- .dma_rx_sync = OMAP_DMA_MCBSP1_RX,
- .dma_tx_sync = OMAP_DMA_MCBSP1_TX,
- .rx_irq = INT_McBSP1RX,
- .tx_irq = INT_McBSP1TX },
- [1] = { .virt_base = io_p2v(OMAP1610_MCBSP2_BASE),
- .dma_rx_sync = OMAP_DMA_MCBSP2_RX,
- .dma_tx_sync = OMAP_DMA_MCBSP2_TX,
- .rx_irq = INT_1610_McBSP2_RX,
- .tx_irq = INT_1610_McBSP2_TX },
- [2] = { .virt_base = OMAP1610_MCBSP3_BASE,
- .dma_rx_sync = OMAP_DMA_MCBSP3_RX,
- .dma_tx_sync = OMAP_DMA_MCBSP3_TX,
- .rx_irq = INT_McBSP3RX,
- .tx_irq = INT_McBSP3TX },
-};
-#endif
-
-static int __init omap_mcbsp_init(void)
-{
- int mcbsp_count = 0, i;
- static const struct omap_mcbsp_info *mcbsp_info;
-
- printk("Initializing OMAP McBSP system\n");
-
- mcbsp_dsp_ck = clk_get(0, "dsp_ck");
- if (IS_ERR(mcbsp_dsp_ck)) {
- printk(KERN_ERR "mcbsp: could not acquire dsp_ck handle.\n");
- return PTR_ERR(mcbsp_dsp_ck);
- }
- mcbsp_api_ck = clk_get(0, "api_ck");
- if (IS_ERR(mcbsp_dsp_ck)) {
- printk(KERN_ERR "mcbsp: could not acquire api_ck handle.\n");
- return PTR_ERR(mcbsp_api_ck);
- }
-
-#ifdef CONFIG_ARCH_OMAP730
- if (cpu_is_omap730()) {
- mcbsp_info = mcbsp_730;
- mcbsp_count = ARRAY_SIZE(mcbsp_730);
- }
-#endif
-#ifdef CONFIG_ARCH_OMAP1510
- if (cpu_is_omap1510()) {
- mcbsp_info = mcbsp_1510;
- mcbsp_count = ARRAY_SIZE(mcbsp_1510);
- }
-#endif
-#if defined(CONFIG_ARCH_OMAP16XX)
- if (cpu_is_omap1610() || cpu_is_omap1710()) {
- mcbsp_info = mcbsp_1610;
- mcbsp_count = ARRAY_SIZE(mcbsp_1610);
- }
-#endif
- for (i = 0; i < OMAP_MAX_MCBSP_COUNT ; i++) {
- if (i >= mcbsp_count) {
- mcbsp[i].io_base = 0;
- mcbsp[i].free = 0;
- continue;
- }
- mcbsp[i].id = i + 1;
- mcbsp[i].free = 1;
- mcbsp[i].dma_tx_lch = -1;
- mcbsp[i].dma_rx_lch = -1;
-
- mcbsp[i].io_base = mcbsp_info[i].virt_base;
- mcbsp[i].tx_irq = mcbsp_info[i].tx_irq;
- mcbsp[i].rx_irq = mcbsp_info[i].rx_irq;
- mcbsp[i].dma_rx_sync = mcbsp_info[i].dma_rx_sync;
- mcbsp[i].dma_tx_sync = mcbsp_info[i].dma_tx_sync;
- spin_lock_init(&mcbsp[i].lock);
- }
-
- return 0;
-}
-
-
-arch_initcall(omap_mcbsp_init);
-
-EXPORT_SYMBOL(omap_mcbsp_config);
-EXPORT_SYMBOL(omap_mcbsp_request);
-EXPORT_SYMBOL(omap_mcbsp_free);
-EXPORT_SYMBOL(omap_mcbsp_start);
-EXPORT_SYMBOL(omap_mcbsp_stop);
-EXPORT_SYMBOL(omap_mcbsp_xmit_word);
-EXPORT_SYMBOL(omap_mcbsp_recv_word);
-EXPORT_SYMBOL(omap_mcbsp_xmit_buffer);
-EXPORT_SYMBOL(omap_mcbsp_recv_buffer);
-EXPORT_SYMBOL(omap_mcbsp_set_spi_mode);
+++ /dev/null
-/*
- * linux/arch/arm/mach-omap/mux.c
- *
- * Utility to set the Omap MUX and PULL_DWN registers from a table in mux.h
- *
- * Copyright (C) 2003 Nokia Corporation
- *
- * Written by Tony Lindgren <tony.lindgren@nokia.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- */
-#include <linux/config.h>
-#include <linux/module.h>
-#include <linux/init.h>
-#include <asm/system.h>
-#include <asm/io.h>
-#include <linux/spinlock.h>
-
-#define __MUX_C__
-#include <asm/arch/mux.h>
-
-#ifdef CONFIG_OMAP_MUX
-
-/*
- * Sets the Omap MUX and PULL_DWN registers based on the table
- */
-int __init_or_module
-omap_cfg_reg(const reg_cfg_t reg_cfg)
-{
- static DEFINE_SPINLOCK(mux_spin_lock);
-
- unsigned long flags;
- reg_cfg_set *cfg;
- unsigned int reg_orig = 0, reg = 0, pu_pd_orig = 0, pu_pd = 0,
- pull_orig = 0, pull = 0;
- unsigned int mask, warn = 0;
-
- if (reg_cfg > ARRAY_SIZE(reg_cfg_table)) {
- printk(KERN_ERR "MUX: reg_cfg %d\n", reg_cfg);
- return -EINVAL;
- }
-
- cfg = ®_cfg_table[reg_cfg];
-
- /*
- * We do a pretty long section here with lock on, but pin muxing
- * should only happen on driver init for each driver, so it's not time
- * critical.
- */
- spin_lock_irqsave(&mux_spin_lock, flags);
-
- /* Check the mux register in question */
- if (cfg->mux_reg) {
- unsigned tmp1, tmp2;
-
- reg_orig = omap_readl(cfg->mux_reg);
-
- /* The mux registers always seem to be 3 bits long */
- mask = (0x7 << cfg->mask_offset);
- tmp1 = reg_orig & mask;
- reg = reg_orig & ~mask;
-
- tmp2 = (cfg->mask << cfg->mask_offset);
- reg |= tmp2;
-
- if (tmp1 != tmp2)
- warn = 1;
-
- omap_writel(reg, cfg->mux_reg);
- }
-
- /* Check for pull up or pull down selection on 1610 */
- if (!cpu_is_omap1510()) {
- if (cfg->pu_pd_reg && cfg->pull_val) {
- pu_pd_orig = omap_readl(cfg->pu_pd_reg);
- mask = 1 << cfg->pull_bit;
-
- if (cfg->pu_pd_val) {
- if (!(pu_pd_orig & mask))
- warn = 1;
- /* Use pull up */
- pu_pd = pu_pd_orig | mask;
- } else {
- if (pu_pd_orig & mask)
- warn = 1;
- /* Use pull down */
- pu_pd = pu_pd_orig & ~mask;
- }
- omap_writel(pu_pd, cfg->pu_pd_reg);
- }
- }
-
- /* Check for an associated pull down register */
- if (cfg->pull_reg) {
- pull_orig = omap_readl(cfg->pull_reg);
- mask = 1 << cfg->pull_bit;
-
- if (cfg->pull_val) {
- if (pull_orig & mask)
- warn = 1;
- /* Low bit = pull enabled */
- pull = pull_orig & ~mask;
- } else {
- if (!(pull_orig & mask))
- warn = 1;
- /* High bit = pull disabled */
- pull = pull_orig | mask;
- }
-
- omap_writel(pull, cfg->pull_reg);
- }
-
- if (warn) {
-#ifdef CONFIG_OMAP_MUX_WARNINGS
- printk(KERN_WARNING "MUX: initialized %s\n", cfg->name);
-#endif
- }
-
-#ifdef CONFIG_OMAP_MUX_DEBUG
- if (cfg->debug || warn) {
- printk("MUX: Setting register %s\n", cfg->name);
- printk(" %s (0x%08x) = 0x%08x -> 0x%08x\n",
- cfg->mux_reg_name, cfg->mux_reg, reg_orig, reg);
-
- if (!cpu_is_omap1510()) {
- if (cfg->pu_pd_reg && cfg->pull_val) {
- printk(" %s (0x%08x) = 0x%08x -> 0x%08x\n",
- cfg->pu_pd_name, cfg->pu_pd_reg,
- pu_pd_orig, pu_pd);
- }
- }
-
- if (cfg->pull_reg)
- printk(" %s (0x%08x) = 0x%08x -> 0x%08x\n",
- cfg->pull_name, cfg->pull_reg, pull_orig, pull);
- }
-#endif
-
- spin_unlock_irqrestore(&mux_spin_lock, flags);
-
-#ifdef CONFIG_OMAP_MUX_ERRORS
- return warn ? -ETXTBSY : 0;
-#else
- return 0;
-#endif
-}
-
-EXPORT_SYMBOL(omap_cfg_reg);
-
-#endif /* CONFIG_OMAP_MUX */
+++ /dev/null
-/*
- * linux/arch/arm/mach-omap/ocpi.c
- *
- * Minimal OCP bus support for omap16xx
- *
- * Copyright (C) 2003 - 2005 Nokia Corporation
- * Written by Tony Lindgren <tony@atomide.com>
- *
- * Modified for clock framework by Paul Mundt <paul.mundt@nokia.com>.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- */
-
-#include <linux/config.h>
-#include <linux/module.h>
-#include <linux/version.h>
-#include <linux/types.h>
-#include <linux/errno.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/spinlock.h>
-#include <linux/err.h>
-
-#include <asm/io.h>
-#include <asm/hardware/clock.h>
-#include <asm/arch/hardware.h>
-
-#define OCPI_BASE 0xfffec320
-#define OCPI_FAULT (OCPI_BASE + 0x00)
-#define OCPI_CMD_FAULT (OCPI_BASE + 0x04)
-#define OCPI_SINT0 (OCPI_BASE + 0x08)
-#define OCPI_TABORT (OCPI_BASE + 0x0c)
-#define OCPI_SINT1 (OCPI_BASE + 0x10)
-#define OCPI_PROT (OCPI_BASE + 0x14)
-#define OCPI_SEC (OCPI_BASE + 0x18)
-
-/* USB OHCI OCPI access error registers */
-#define HOSTUEADDR 0xfffba0e0
-#define HOSTUESTATUS 0xfffba0e4
-
-static struct clk *ocpi_ck;
-
-/*
- * Enables device access to OMAP buses via the OCPI bridge
- * FIXME: Add locking
- */
-int ocpi_enable(void)
-{
- unsigned int val;
-
- if (!cpu_is_omap16xx())
- return -ENODEV;
-
- /* Make sure there's clock for OCPI */
- clk_enable(ocpi_ck);
-
- /* Enable access for OHCI in OCPI */
- val = omap_readl(OCPI_PROT);
- val &= ~0xff;
- //val &= (1 << 0); /* Allow access only to EMIFS */
- omap_writel(val, OCPI_PROT);
-
- val = omap_readl(OCPI_SEC);
- val &= ~0xff;
- omap_writel(val, OCPI_SEC);
-
- return 0;
-}
-EXPORT_SYMBOL(ocpi_enable);
-
-static int __init omap_ocpi_init(void)
-{
- if (!cpu_is_omap16xx())
- return -ENODEV;
-
- ocpi_ck = clk_get(NULL, "l3_ocpi_ck");
- if (IS_ERR(ocpi_ck))
- return PTR_ERR(ocpi_ck);
-
- clk_use(ocpi_ck);
- ocpi_enable();
- printk("OMAP OCPI interconnect driver loaded\n");
-
- return 0;
-}
-
-static void __exit omap_ocpi_exit(void)
-{
- /* REVISIT: Disable OCPI */
-
- if (!cpu_is_omap16xx())
- return;
-
- clk_unuse(ocpi_ck);
- clk_put(ocpi_ck);
-}
-
-MODULE_AUTHOR("Tony Lindgren <tony@atomide.com>");
-MODULE_DESCRIPTION("OMAP OCPI bus controller module");
-MODULE_LICENSE("GPL");
-module_init(omap_ocpi_init);
-module_exit(omap_ocpi_exit);
+++ /dev/null
-/*
- * linux/arch/arm/mach-omap/pm.c
- *
- * OMAP Power Management Routines
- *
- * Original code for the SA11x0:
- * Copyright (c) 2001 Cliff Brake <cbrake@accelent.com>
- *
- * Modified for the PXA250 by Nicolas Pitre:
- * Copyright (c) 2002 Monta Vista Software, Inc.
- *
- * Modified for the OMAP1510 by David Singleton:
- * Copyright (c) 2002 Monta Vista Software, Inc.
- *
- * Cleanup 2004 for OMAP1510/1610 by Dirk Behme <dirk.behme@de.bosch.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/pm.h>
-#include <linux/sched.h>
-#include <linux/proc_fs.h>
-#include <linux/pm.h>
-
-#include <asm/io.h>
-#include <asm/mach/time.h>
-#include <asm/mach-types.h>
-
-#include <asm/arch/omap16xx.h>
-#include <asm/arch/pm.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/tc.h>
-#include <asm/arch/tps65010.h>
-
-#include "clock.h"
-
-static unsigned int arm_sleep_save[ARM_SLEEP_SAVE_SIZE];
-static unsigned short ulpd_sleep_save[ULPD_SLEEP_SAVE_SIZE];
-static unsigned int mpui1510_sleep_save[MPUI1510_SLEEP_SAVE_SIZE];
-static unsigned int mpui1610_sleep_save[MPUI1610_SLEEP_SAVE_SIZE];
-
-/*
- * Let's power down on idle, but only if we are really
- * idle, because once we start down the path of
- * going idle we continue to do idle even if we get
- * a clock tick interrupt . .
- */
-void omap_pm_idle(void)
-{
- int (*func_ptr)(void) = 0;
- unsigned int mask32 = 0;
-
- /*
- * If the DSP is being used let's just idle the CPU, the overhead
- * to wake up from Big Sleep is big, milliseconds versus micro
- * seconds for wait for interrupt.
- */
-
- local_irq_disable();
- local_fiq_disable();
- if (need_resched()) {
- local_fiq_enable();
- local_irq_enable();
- return;
- }
- mask32 = omap_readl(ARM_SYSST);
-
- /*
- * Since an interrupt may set up a timer, we don't want to
- * reprogram the hardware timer with interrupts enabled.
- * Re-enable interrupts only after returning from idle.
- */
- timer_dyn_reprogram();
-
- if ((mask32 & DSP_IDLE) == 0) {
- __asm__ volatile ("mcr p15, 0, r0, c7, c0, 4");
- } else {
-
- if (cpu_is_omap1510()) {
- func_ptr = (void *)(OMAP1510_SRAM_IDLE_SUSPEND);
- } else if (cpu_is_omap1610() || cpu_is_omap1710()) {
- func_ptr = (void *)(OMAP1610_SRAM_IDLE_SUSPEND);
- } else if (cpu_is_omap5912()) {
- func_ptr = (void *)(OMAP5912_SRAM_IDLE_SUSPEND);
- }
-
- func_ptr();
- }
- local_fiq_enable();
- local_irq_enable();
-}
-
-/*
- * Configuration of the wakeup event is board specific. For the
- * moment we put it into this helper function. Later it may move
- * to board specific files.
- */
-static void omap_pm_wakeup_setup(void)
-{
- /*
- * Enable ARM XOR clock and release peripheral from reset by
- * writing 1 to PER_EN bit in ARM_RSTCT2, this is required
- * for UART configuration to use UART2 to wake up.
- */
-
- omap_writel(omap_readl(ARM_IDLECT2) | ENABLE_XORCLK, ARM_IDLECT2);
- omap_writel(omap_readl(ARM_RSTCT2) | PER_EN, ARM_RSTCT2);
- omap_writew(MODEM_32K_EN, ULPD_CLOCK_CTRL);
-
- /*
- * Turn off all interrupts except L1-2nd level cascade,
- * and the L2 wakeup interrupts: keypad and UART2.
- */
-
- omap_writel(~IRQ_LEVEL2, OMAP_IH1_MIR);
-
- if (cpu_is_omap1510()) {
- omap_writel(~(IRQ_UART2 | IRQ_KEYBOARD), OMAP_IH2_MIR);
- }
-
- if (cpu_is_omap16xx()) {
- omap_writel(~(IRQ_UART2 | IRQ_KEYBOARD), OMAP_IH2_0_MIR);
-
- omap_writel(~0x0, OMAP_IH2_1_MIR);
- omap_writel(~0x0, OMAP_IH2_2_MIR);
- omap_writel(~0x0, OMAP_IH2_3_MIR);
- }
-
- /* New IRQ agreement */
- omap_writel(1, OMAP_IH1_CONTROL);
-
- /* external PULL to down, bit 22 = 0 */
- omap_writel(omap_readl(PULL_DWN_CTRL_2) & ~(1<<22), PULL_DWN_CTRL_2);
-}
-
-void omap_pm_suspend(void)
-{
- unsigned int mask32 = 0;
- unsigned long arg0 = 0, arg1 = 0;
- int (*func_ptr)(unsigned short, unsigned short) = 0;
- unsigned short save_dsp_idlect2;
-
- printk("PM: OMAP%x is entering deep sleep now ...\n", system_rev);
-
- if (machine_is_omap_osk()) {
- /* Stop LED1 (D9) blink */
- tps65010_set_led(LED1, OFF);
- }
-
- /*
- * Step 1: turn off interrupts
- */
-
- local_irq_disable();
- local_fiq_disable();
-
- /*
- * Step 2: save registers
- *
- * The omap is a strange/beautiful device. The caches, memory
- * and register state are preserved across power saves.
- * We have to save and restore very little register state to
- * idle the omap.
- *
- * Save interrupt, MPUI, ARM and UPLD control registers.
- */
-
- if (cpu_is_omap1510()) {
- MPUI1510_SAVE(OMAP_IH1_MIR);
- MPUI1510_SAVE(OMAP_IH2_MIR);
- MPUI1510_SAVE(MPUI_CTRL);
- MPUI1510_SAVE(MPUI_DSP_BOOT_CONFIG);
- MPUI1510_SAVE(MPUI_DSP_API_CONFIG);
- MPUI1510_SAVE(EMIFS_CONFIG);
- MPUI1510_SAVE(EMIFF_SDRAM_CONFIG);
- } else if (cpu_is_omap16xx()) {
- MPUI1610_SAVE(OMAP_IH1_MIR);
- MPUI1610_SAVE(OMAP_IH2_0_MIR);
- MPUI1610_SAVE(OMAP_IH2_1_MIR);
- MPUI1610_SAVE(OMAP_IH2_2_MIR);
- MPUI1610_SAVE(OMAP_IH2_3_MIR);
- MPUI1610_SAVE(MPUI_CTRL);
- MPUI1610_SAVE(MPUI_DSP_BOOT_CONFIG);
- MPUI1610_SAVE(MPUI_DSP_API_CONFIG);
- MPUI1610_SAVE(EMIFS_CONFIG);
- MPUI1610_SAVE(EMIFF_SDRAM_CONFIG);
- }
-
- ARM_SAVE(ARM_CKCTL);
- ARM_SAVE(ARM_IDLECT1);
- ARM_SAVE(ARM_IDLECT2);
- ARM_SAVE(ARM_EWUPCT);
- ARM_SAVE(ARM_RSTCT1);
- ARM_SAVE(ARM_RSTCT2);
- ARM_SAVE(ARM_SYSST);
- ULPD_SAVE(ULPD_CLOCK_CTRL);
- ULPD_SAVE(ULPD_STATUS_REQ);
-
- /*
- * Step 3: LOW_PWR signal enabling
- *
- * Allow the LOW_PWR signal to be visible on MPUIO5 ball.
- */
- if (cpu_is_omap1510()) {
- /* POWER_CTRL_REG = 0x1 (LOW_POWER is available) */
- omap_writew(omap_readw(ULPD_POWER_CTRL) |
- OMAP1510_ULPD_LOW_POWER_REQ, ULPD_POWER_CTRL);
- } else if (cpu_is_omap16xx()) {
- /* POWER_CTRL_REG = 0x1 (LOW_POWER is available) */
- omap_writew(omap_readw(ULPD_POWER_CTRL) |
- OMAP1610_ULPD_LOW_POWER_REQ, ULPD_POWER_CTRL);
- }
-
- /* configure LOW_PWR pin */
- omap_cfg_reg(T20_1610_LOW_PWR);
-
- /*
- * Step 4: OMAP DSP Shutdown
- */
-
- /* Set DSP_RST = 1 and DSP_EN = 0, put DSP block into reset */
- omap_writel((omap_readl(ARM_RSTCT1) | DSP_RST) & ~DSP_ENABLE,
- ARM_RSTCT1);
-
- /* Set DSP boot mode to DSP-IDLE, DSP_BOOT_MODE = 0x2 */
- omap_writel(DSP_IDLE_MODE, MPUI_DSP_BOOT_CONFIG);
-
- /* Set EN_DSPCK = 0, stop DSP block clock */
- omap_writel(omap_readl(ARM_CKCTL) & ~DSP_CLOCK_ENABLE, ARM_CKCTL);
-
- /* Stop any DSP domain clocks */
- omap_writel(omap_readl(ARM_IDLECT2) | (1<<EN_APICK), ARM_IDLECT2);
- save_dsp_idlect2 = __raw_readw(DSP_IDLECT2);
- __raw_writew(0, DSP_IDLECT2);
-
- /*
- * Step 5: Wakeup Event Setup
- */
-
- omap_pm_wakeup_setup();
-
- /*
- * Step 6a: ARM and Traffic controller shutdown
- *
- * Step 6 starts here with clock and watchdog disable
- */
-
- /* stop clocks */
- mask32 = omap_readl(ARM_IDLECT2);
- mask32 &= ~(1<<EN_WDTCK); /* bit 0 -> 0 (WDT clock) */
- mask32 |= (1<<EN_XORPCK); /* bit 1 -> 1 (XORPCK clock) */
- mask32 &= ~(1<<EN_PERCK); /* bit 2 -> 0 (MPUPER_CK clock) */
- mask32 &= ~(1<<EN_LCDCK); /* bit 3 -> 0 (LCDC clock) */
- mask32 &= ~(1<<EN_LBCK); /* bit 4 -> 0 (local bus clock) */
- mask32 |= (1<<EN_APICK); /* bit 6 -> 1 (MPUI clock) */
- mask32 &= ~(1<<EN_TIMCK); /* bit 7 -> 0 (MPU timer clock) */
- mask32 &= ~(1<<DMACK_REQ); /* bit 8 -> 0 (DMAC clock) */
- mask32 &= ~(1<<EN_GPIOCK); /* bit 9 -> 0 (GPIO clock) */
- omap_writel(mask32, ARM_IDLECT2);
-
- /* disable ARM watchdog */
- omap_writel(0x00F5, OMAP_WDT_TIMER_MODE);
- omap_writel(0x00A0, OMAP_WDT_TIMER_MODE);
-
- /*
- * Step 6b: ARM and Traffic controller shutdown
- *
- * Step 6 continues here. Prepare jump to power management
- * assembly code in internal SRAM.
- *
- * Since the omap_cpu_suspend routine has been copied to
- * SRAM, we'll do an indirect procedure call to it and pass the
- * contents of arm_idlect1 and arm_idlect2 so it can restore
- * them when it wakes up and it will return.
- */
-
- arg0 = arm_sleep_save[ARM_SLEEP_SAVE_ARM_IDLECT1];
- arg1 = arm_sleep_save[ARM_SLEEP_SAVE_ARM_IDLECT2];
-
- if (cpu_is_omap1510()) {
- func_ptr = (void *)(OMAP1510_SRAM_API_SUSPEND);
- } else if (cpu_is_omap1610() || cpu_is_omap1710()) {
- func_ptr = (void *)(OMAP1610_SRAM_API_SUSPEND);
- } else if (cpu_is_omap5912()) {
- func_ptr = (void *)(OMAP5912_SRAM_API_SUSPEND);
- }
-
- /*
- * Step 6c: ARM and Traffic controller shutdown
- *
- * Jump to assembly code. The processor will stay there
- * until wake up.
- */
-
- func_ptr(arg0, arg1);
-
- /*
- * If we are here, processor is woken up!
- */
-
- if (cpu_is_omap1510()) {
- /* POWER_CTRL_REG = 0x0 (LOW_POWER is disabled) */
- omap_writew(omap_readw(ULPD_POWER_CTRL) &
- ~OMAP1510_ULPD_LOW_POWER_REQ, ULPD_POWER_CTRL);
- } else if (cpu_is_omap16xx()) {
- /* POWER_CTRL_REG = 0x0 (LOW_POWER is disabled) */
- omap_writew(omap_readw(ULPD_POWER_CTRL) &
- ~OMAP1610_ULPD_LOW_POWER_REQ, ULPD_POWER_CTRL);
- }
-
-
- /* Restore DSP clocks */
- omap_writel(omap_readl(ARM_IDLECT2) | (1<<EN_APICK), ARM_IDLECT2);
- __raw_writew(save_dsp_idlect2, DSP_IDLECT2);
- ARM_RESTORE(ARM_IDLECT2);
-
- /*
- * Restore ARM state, except ARM_IDLECT1/2 which omap_cpu_suspend did
- */
-
- ARM_RESTORE(ARM_CKCTL);
- ARM_RESTORE(ARM_EWUPCT);
- ARM_RESTORE(ARM_RSTCT1);
- ARM_RESTORE(ARM_RSTCT2);
- ARM_RESTORE(ARM_SYSST);
- ULPD_RESTORE(ULPD_CLOCK_CTRL);
- ULPD_RESTORE(ULPD_STATUS_REQ);
-
- if (cpu_is_omap1510()) {
- MPUI1510_RESTORE(MPUI_CTRL);
- MPUI1510_RESTORE(MPUI_DSP_BOOT_CONFIG);
- MPUI1510_RESTORE(MPUI_DSP_API_CONFIG);
- MPUI1510_RESTORE(EMIFS_CONFIG);
- MPUI1510_RESTORE(EMIFF_SDRAM_CONFIG);
- MPUI1510_RESTORE(OMAP_IH1_MIR);
- MPUI1510_RESTORE(OMAP_IH2_MIR);
- } else if (cpu_is_omap16xx()) {
- MPUI1610_RESTORE(MPUI_CTRL);
- MPUI1610_RESTORE(MPUI_DSP_BOOT_CONFIG);
- MPUI1610_RESTORE(MPUI_DSP_API_CONFIG);
- MPUI1610_RESTORE(EMIFS_CONFIG);
- MPUI1610_RESTORE(EMIFF_SDRAM_CONFIG);
-
- MPUI1610_RESTORE(OMAP_IH1_MIR);
- MPUI1610_RESTORE(OMAP_IH2_0_MIR);
- MPUI1610_RESTORE(OMAP_IH2_1_MIR);
- MPUI1610_RESTORE(OMAP_IH2_2_MIR);
- MPUI1610_RESTORE(OMAP_IH2_3_MIR);
- }
-
- /*
- * Reenable interrupts
- */
-
- local_irq_enable();
- local_fiq_enable();
-
- printk("PM: OMAP%x is re-starting from deep sleep...\n", system_rev);
-
- if (machine_is_omap_osk()) {
- /* Let LED1 (D9) blink again */
- tps65010_set_led(LED1, BLINK);
- }
-}
-
-#if defined(DEBUG) && defined(CONFIG_PROC_FS)
-static int g_read_completed;
-
-/*
- * Read system PM registers for debugging
- */
-static int omap_pm_read_proc(
- char *page_buffer,
- char **my_first_byte,
- off_t virtual_start,
- int length,
- int *eof,
- void *data)
-{
- int my_buffer_offset = 0;
- char * const my_base = page_buffer;
-
- ARM_SAVE(ARM_CKCTL);
- ARM_SAVE(ARM_IDLECT1);
- ARM_SAVE(ARM_IDLECT2);
- ARM_SAVE(ARM_EWUPCT);
- ARM_SAVE(ARM_RSTCT1);
- ARM_SAVE(ARM_RSTCT2);
- ARM_SAVE(ARM_SYSST);
-
- ULPD_SAVE(ULPD_IT_STATUS);
- ULPD_SAVE(ULPD_CLOCK_CTRL);
- ULPD_SAVE(ULPD_SOFT_REQ);
- ULPD_SAVE(ULPD_STATUS_REQ);
- ULPD_SAVE(ULPD_DPLL_CTRL);
- ULPD_SAVE(ULPD_POWER_CTRL);
-
- if (cpu_is_omap1510()) {
- MPUI1510_SAVE(MPUI_CTRL);
- MPUI1510_SAVE(MPUI_DSP_STATUS);
- MPUI1510_SAVE(MPUI_DSP_BOOT_CONFIG);
- MPUI1510_SAVE(MPUI_DSP_API_CONFIG);
- MPUI1510_SAVE(EMIFF_SDRAM_CONFIG);
- MPUI1510_SAVE(EMIFS_CONFIG);
- } else if (cpu_is_omap16xx()) {
- MPUI1610_SAVE(MPUI_CTRL);
- MPUI1610_SAVE(MPUI_DSP_STATUS);
- MPUI1610_SAVE(MPUI_DSP_BOOT_CONFIG);
- MPUI1610_SAVE(MPUI_DSP_API_CONFIG);
- MPUI1610_SAVE(EMIFF_SDRAM_CONFIG);
- MPUI1610_SAVE(EMIFS_CONFIG);
- }
-
- if (virtual_start == 0) {
- g_read_completed = 0;
-
- my_buffer_offset += sprintf(my_base + my_buffer_offset,
- "ARM_CKCTL_REG: 0x%-8x \n"
- "ARM_IDLECT1_REG: 0x%-8x \n"
- "ARM_IDLECT2_REG: 0x%-8x \n"
- "ARM_EWUPCT_REG: 0x%-8x \n"
- "ARM_RSTCT1_REG: 0x%-8x \n"
- "ARM_RSTCT2_REG: 0x%-8x \n"
- "ARM_SYSST_REG: 0x%-8x \n"
- "ULPD_IT_STATUS_REG: 0x%-4x \n"
- "ULPD_CLOCK_CTRL_REG: 0x%-4x \n"
- "ULPD_SOFT_REQ_REG: 0x%-4x \n"
- "ULPD_DPLL_CTRL_REG: 0x%-4x \n"
- "ULPD_STATUS_REQ_REG: 0x%-4x \n"
- "ULPD_POWER_CTRL_REG: 0x%-4x \n",
- ARM_SHOW(ARM_CKCTL),
- ARM_SHOW(ARM_IDLECT1),
- ARM_SHOW(ARM_IDLECT2),
- ARM_SHOW(ARM_EWUPCT),
- ARM_SHOW(ARM_RSTCT1),
- ARM_SHOW(ARM_RSTCT2),
- ARM_SHOW(ARM_SYSST),
- ULPD_SHOW(ULPD_IT_STATUS),
- ULPD_SHOW(ULPD_CLOCK_CTRL),
- ULPD_SHOW(ULPD_SOFT_REQ),
- ULPD_SHOW(ULPD_DPLL_CTRL),
- ULPD_SHOW(ULPD_STATUS_REQ),
- ULPD_SHOW(ULPD_POWER_CTRL));
-
- if (cpu_is_omap1510()) {
- my_buffer_offset += sprintf(my_base + my_buffer_offset,
- "MPUI1510_CTRL_REG 0x%-8x \n"
- "MPUI1510_DSP_STATUS_REG: 0x%-8x \n"
- "MPUI1510_DSP_BOOT_CONFIG_REG: 0x%-8x \n"
- "MPUI1510_DSP_API_CONFIG_REG: 0x%-8x \n"
- "MPUI1510_SDRAM_CONFIG_REG: 0x%-8x \n"
- "MPUI1510_EMIFS_CONFIG_REG: 0x%-8x \n",
- MPUI1510_SHOW(MPUI_CTRL),
- MPUI1510_SHOW(MPUI_DSP_STATUS),
- MPUI1510_SHOW(MPUI_DSP_BOOT_CONFIG),
- MPUI1510_SHOW(MPUI_DSP_API_CONFIG),
- MPUI1510_SHOW(EMIFF_SDRAM_CONFIG),
- MPUI1510_SHOW(EMIFS_CONFIG));
- } else if (cpu_is_omap16xx()) {
- my_buffer_offset += sprintf(my_base + my_buffer_offset,
- "MPUI1610_CTRL_REG 0x%-8x \n"
- "MPUI1610_DSP_STATUS_REG: 0x%-8x \n"
- "MPUI1610_DSP_BOOT_CONFIG_REG: 0x%-8x \n"
- "MPUI1610_DSP_API_CONFIG_REG: 0x%-8x \n"
- "MPUI1610_SDRAM_CONFIG_REG: 0x%-8x \n"
- "MPUI1610_EMIFS_CONFIG_REG: 0x%-8x \n",
- MPUI1610_SHOW(MPUI_CTRL),
- MPUI1610_SHOW(MPUI_DSP_STATUS),
- MPUI1610_SHOW(MPUI_DSP_BOOT_CONFIG),
- MPUI1610_SHOW(MPUI_DSP_API_CONFIG),
- MPUI1610_SHOW(EMIFF_SDRAM_CONFIG),
- MPUI1610_SHOW(EMIFS_CONFIG));
- }
-
- g_read_completed++;
- } else if (g_read_completed >= 1) {
- *eof = 1;
- return 0;
- }
- g_read_completed++;
-
- *my_first_byte = page_buffer;
- return my_buffer_offset;
-}
-
-static void omap_pm_init_proc(void)
-{
- struct proc_dir_entry *entry;
-
- entry = create_proc_read_entry("driver/omap_pm",
- S_IWUSR | S_IRUGO, NULL,
- omap_pm_read_proc, 0);
-}
-
-#endif /* DEBUG && CONFIG_PROC_FS */
-
-/*
- * omap_pm_prepare - Do preliminary suspend work.
- * @state: suspend state we're entering.
- *
- */
-//#include <asm/arch/hardware.h>
-
-static int omap_pm_prepare(suspend_state_t state)
-{
- int error = 0;
-
- switch (state)
- {
- case PM_SUSPEND_STANDBY:
- case PM_SUSPEND_MEM:
- break;
-
- case PM_SUSPEND_DISK:
- return -ENOTSUPP;
-
- default:
- return -EINVAL;
- }
-
- return error;
-}
-
-
-/*
- * omap_pm_enter - Actually enter a sleep state.
- * @state: State we're entering.
- *
- */
-
-static int omap_pm_enter(suspend_state_t state)
-{
- switch (state)
- {
- case PM_SUSPEND_STANDBY:
- case PM_SUSPEND_MEM:
- omap_pm_suspend();
- break;
-
- case PM_SUSPEND_DISK:
- return -ENOTSUPP;
-
- default:
- return -EINVAL;
- }
-
- return 0;
-}
-
-
-/**
- * omap_pm_finish - Finish up suspend sequence.
- * @state: State we're coming out of.
- *
- * This is called after we wake back up (or if entering the sleep state
- * failed).
- */
-
-static int omap_pm_finish(suspend_state_t state)
-{
- return 0;
-}
-
-
-struct pm_ops omap_pm_ops ={
- .pm_disk_mode = 0,
- .prepare = omap_pm_prepare,
- .enter = omap_pm_enter,
- .finish = omap_pm_finish,
-};
-
-static int __init omap_pm_init(void)
-{
- printk("Power Management for TI OMAP.\n");
- pm_idle = omap_pm_idle;
- /*
- * We copy the assembler sleep/wakeup routines to SRAM.
- * These routines need to be in SRAM as that's the only
- * memory the MPU can see when it wakes up.
- */
-
-#ifdef CONFIG_ARCH_OMAP1510
- if (cpu_is_omap1510()) {
- memcpy((void *)OMAP1510_SRAM_IDLE_SUSPEND,
- omap1510_idle_loop_suspend,
- omap1510_idle_loop_suspend_sz);
- memcpy((void *)OMAP1510_SRAM_API_SUSPEND, omap1510_cpu_suspend,
- omap1510_cpu_suspend_sz);
- } else
-#endif
- if (cpu_is_omap1610() || cpu_is_omap1710()) {
- memcpy((void *)OMAP1610_SRAM_IDLE_SUSPEND,
- omap1610_idle_loop_suspend,
- omap1610_idle_loop_suspend_sz);
- memcpy((void *)OMAP1610_SRAM_API_SUSPEND, omap1610_cpu_suspend,
- omap1610_cpu_suspend_sz);
- } else if (cpu_is_omap5912()) {
- memcpy((void *)OMAP5912_SRAM_IDLE_SUSPEND,
- omap1610_idle_loop_suspend,
- omap1610_idle_loop_suspend_sz);
- memcpy((void *)OMAP5912_SRAM_API_SUSPEND, omap1610_cpu_suspend,
- omap1610_cpu_suspend_sz);
- }
-
- pm_set_ops(&omap_pm_ops);
-
-#if defined(DEBUG) && defined(CONFIG_PROC_FS)
- omap_pm_init_proc();
-#endif
-
- return 0;
-}
-__initcall(omap_pm_init);
-
+++ /dev/null
-/*
- * linux/arch/arm/mach-omap/sleep.S
- *
- * Low-level OMAP1510/1610 sleep/wakeUp support
- *
- * Initial SA1110 code:
- * Copyright (c) 2001 Cliff Brake <cbrake@accelent.com>
- *
- * Adapted for PXA by Nicolas Pitre:
- * Copyright (c) 2002 Monta Vista Software, Inc.
- *
- * Support for OMAP1510/1610 by Dirk Behme <dirk.behme@de.bosch.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/config.h>
-#include <linux/linkage.h>
-#include <asm/assembler.h>
-#include <asm/arch/io.h>
-#include <asm/arch/pm.h>
-
- .text
-
-/*
- * Forces OMAP into idle state
- *
- * omapXXXX_idle_loop_suspend()
- *
- * Note: This code get's copied to internal SRAM at boot. When the OMAP
- * wakes up it continues execution at the point it went to sleep.
- *
- * Note: Because of slightly different configuration values we have
- * processor specific functions here.
- */
-
-#ifdef CONFIG_ARCH_OMAP1510
-ENTRY(omap1510_idle_loop_suspend)
-
- stmfd sp!, {r0 - r12, lr} @ save registers on stack
-
- @ load base address of ARM_IDLECT1 and ARM_IDLECT2
- mov r4, #CLKGEN_REG_ASM_BASE & 0xff000000
- orr r4, r4, #CLKGEN_REG_ASM_BASE & 0x00ff0000
- orr r4, r4, #CLKGEN_REG_ASM_BASE & 0x0000ff00
-
- @ turn off clock domains
- @ get ARM_IDLECT2 into r2
- ldrh r2, [r4, #ARM_IDLECT2_ASM_OFFSET & 0xff]
- mov r5, #OMAP1510_IDLE_CLOCK_DOMAINS & 0xff
- orr r5,r5, #OMAP1510_IDLE_CLOCK_DOMAINS & 0xff00
- strh r5, [r4, #ARM_IDLECT2_ASM_OFFSET & 0xff]
-
- @ request ARM idle
- @ get ARM_IDLECT1 into r1
- ldrh r1, [r4, #ARM_IDLECT1_ASM_OFFSET & 0xff]
- orr r3, r1, #OMAP1510_IDLE_LOOP_REQUEST & 0xffff
- strh r3, [r4, #ARM_IDLECT1_ASM_OFFSET & 0xff]
-
- mov r5, #IDLE_WAIT_CYCLES & 0xff
- orr r5, r5, #IDLE_WAIT_CYCLES & 0xff00
-l_1510: subs r5, r5, #1
- bne l_1510
-/*
- * Let's wait for the next clock tick to wake us up.
- */
- mov r0, #0
- mcr p15, 0, r0, c7, c0, 4 @ wait for interrupt
-/*
- * omap1510_idle_loop_suspend()'s resume point.
- *
- * It will just start executing here, so we'll restore stuff from the
- * stack, reset the ARM_IDLECT1 and ARM_IDLECT2.
- */
-
- @ restore ARM_IDLECT1 and ARM_IDLECT2 and return
- @ r1 has ARM_IDLECT1 and r2 still has ARM_IDLECT2
- strh r2, [r4, #ARM_IDLECT2_ASM_OFFSET & 0xff]
- strh r1, [r4, #ARM_IDLECT1_ASM_OFFSET & 0xff]
-
- ldmfd sp!, {r0 - r12, pc} @ restore regs and return
-
-ENTRY(omap1510_idle_loop_suspend_sz)
- .word . - omap1510_idle_loop_suspend
-#endif /* CONFIG_ARCH_OMAP1510 */
-
-#if defined(CONFIG_ARCH_OMAP16XX)
-ENTRY(omap1610_idle_loop_suspend)
-
- stmfd sp!, {r0 - r12, lr} @ save registers on stack
-
- @ load base address of ARM_IDLECT1 and ARM_IDLECT2
- mov r4, #CLKGEN_REG_ASM_BASE & 0xff000000
- orr r4, r4, #CLKGEN_REG_ASM_BASE & 0x00ff0000
- orr r4, r4, #CLKGEN_REG_ASM_BASE & 0x0000ff00
-
- @ turn off clock domains
- @ get ARM_IDLECT2 into r2
- ldrh r2, [r4, #ARM_IDLECT2_ASM_OFFSET & 0xff]
- mov r5, #OMAP1610_IDLE_CLOCK_DOMAINS & 0xff
- orr r5,r5, #OMAP1610_IDLE_CLOCK_DOMAINS & 0xff00
- strh r5, [r4, #ARM_IDLECT2_ASM_OFFSET & 0xff]
-
- @ request ARM idle
- @ get ARM_IDLECT1 into r1
- ldrh r1, [r4, #ARM_IDLECT1_ASM_OFFSET & 0xff]
- orr r3, r1, #OMAP1610_IDLE_LOOP_REQUEST & 0xffff
- strh r3, [r4, #ARM_IDLECT1_ASM_OFFSET & 0xff]
-
- mov r5, #IDLE_WAIT_CYCLES & 0xff
- orr r5, r5, #IDLE_WAIT_CYCLES & 0xff00
-l_1610: subs r5, r5, #1
- bne l_1610
-/*
- * Let's wait for the next clock tick to wake us up.
- */
- mov r0, #0
- mcr p15, 0, r0, c7, c0, 4 @ wait for interrupt
-/*
- * omap1610_idle_loop_suspend()'s resume point.
- *
- * It will just start executing here, so we'll restore stuff from the
- * stack, reset the ARM_IDLECT1 and ARM_IDLECT2.
- */
-
- @ restore ARM_IDLECT1 and ARM_IDLECT2 and return
- @ r1 has ARM_IDLECT1 and r2 still has ARM_IDLECT2
- strh r2, [r4, #ARM_IDLECT2_ASM_OFFSET & 0xff]
- strh r1, [r4, #ARM_IDLECT1_ASM_OFFSET & 0xff]
-
- ldmfd sp!, {r0 - r12, pc} @ restore regs and return
-
-ENTRY(omap1610_idle_loop_suspend_sz)
- .word . - omap1610_idle_loop_suspend
-#endif /* CONFIG_ARCH_OMAP16XX */
-
-/*
- * Forces OMAP into deep sleep state
- *
- * omapXXXX_cpu_suspend()
- *
- * The values of the registers ARM_IDLECT1 and ARM_IDLECT2 are passed
- * as arg0 and arg1 from caller. arg0 is stored in register r0 and arg1
- * in register r1.
- *
- * Note: This code get's copied to internal SRAM at boot. When the OMAP
- * wakes up it continues execution at the point it went to sleep.
- *
- * Note: Because of errata work arounds we have processor specific functions
- * here. They are mostly the same, but slightly different.
- *
- */
-
-#ifdef CONFIG_ARCH_OMAP1510
-ENTRY(omap1510_cpu_suspend)
-
- @ save registers on stack
- stmfd sp!, {r0 - r12, lr}
-
- @ load base address of Traffic Controller
- mov r4, #TCMIF_ASM_BASE & 0xff000000
- orr r4, r4, #TCMIF_ASM_BASE & 0x00ff0000
- orr r4, r4, #TCMIF_ASM_BASE & 0x0000ff00
-
- @ work around errata of OMAP1510 PDE bit for TC shut down
- @ clear PDE bit
- ldr r5, [r4, #EMIFS_CONFIG_ASM_OFFSET & 0xff]
- bic r5, r5, #PDE_BIT & 0xff
- str r5, [r4, #EMIFS_CONFIG_ASM_OFFSET & 0xff]
-
- @ set PWD_EN bit
- and r5, r5, #PWD_EN_BIT & 0xff
- str r5, [r4, #EMIFS_CONFIG_ASM_OFFSET & 0xff]
-
- @ prepare to put SDRAM into self-refresh manually
- ldr r5, [r4, #EMIFF_SDRAM_CONFIG_ASM_OFFSET & 0xff]
- orr r5, r5, #SELF_REFRESH_MODE & 0xff000000
- orr r5, r5, #SELF_REFRESH_MODE & 0x000000ff
- str r5, [r4, #EMIFF_SDRAM_CONFIG_ASM_OFFSET & 0xff]
-
- @ prepare to put EMIFS to Sleep
- ldr r5, [r4, #EMIFS_CONFIG_ASM_OFFSET & 0xff]
- orr r5, r5, #IDLE_EMIFS_REQUEST & 0xff
- str r5, [r4, #EMIFS_CONFIG_ASM_OFFSET & 0xff]
-
- @ load base address of ARM_IDLECT1 and ARM_IDLECT2
- mov r4, #CLKGEN_REG_ASM_BASE & 0xff000000
- orr r4, r4, #CLKGEN_REG_ASM_BASE & 0x00ff0000
- orr r4, r4, #CLKGEN_REG_ASM_BASE & 0x0000ff00
-
- @ turn off clock domains
- mov r5, #OMAP1510_IDLE_CLOCK_DOMAINS & 0xff
- orr r5,r5, #OMAP1510_IDLE_CLOCK_DOMAINS & 0xff00
- strh r5, [r4, #ARM_IDLECT2_ASM_OFFSET & 0xff]
-
- @ request ARM idle
- mov r3, #OMAP1510_DEEP_SLEEP_REQUEST & 0xff
- orr r3, r3, #OMAP1510_DEEP_SLEEP_REQUEST & 0xff00
- strh r3, [r4, #ARM_IDLECT1_ASM_OFFSET & 0xff]
-
- mov r5, #IDLE_WAIT_CYCLES & 0xff
- orr r5, r5, #IDLE_WAIT_CYCLES & 0xff00
-l_1510_2:
- subs r5, r5, #1
- bne l_1510_2
-/*
- * Let's wait for the next wake up event to wake us up. r0 can't be
- * used here because r0 holds ARM_IDLECT1
- */
- mov r2, #0
- mcr p15, 0, r2, c7, c0, 4 @ wait for interrupt
-/*
- * omap1510_cpu_suspend()'s resume point.
- *
- * It will just start executing here, so we'll restore stuff from the
- * stack, reset the ARM_IDLECT1 and ARM_IDLECT2.
- */
- strh r1, [r4, #ARM_IDLECT2_ASM_OFFSET & 0xff]
- strh r0, [r4, #ARM_IDLECT1_ASM_OFFSET & 0xff]
-
- @ restore regs and return
- ldmfd sp!, {r0 - r12, pc}
-
-ENTRY(omap1510_cpu_suspend_sz)
- .word . - omap1510_cpu_suspend
-#endif /* CONFIG_ARCH_OMAP1510 */
-
-#if defined(CONFIG_ARCH_OMAP16XX)
-ENTRY(omap1610_cpu_suspend)
-
- @ save registers on stack
- stmfd sp!, {r0 - r12, lr}
-
- @ load base address of Traffic Controller
- mov r4, #TCMIF_ASM_BASE & 0xff000000
- orr r4, r4, #TCMIF_ASM_BASE & 0x00ff0000
- orr r4, r4, #TCMIF_ASM_BASE & 0x0000ff00
-
- @ prepare to put SDRAM into self-refresh manually
- ldr r5, [r4, #EMIFF_SDRAM_CONFIG_ASM_OFFSET & 0xff]
- orr r5, r5, #SELF_REFRESH_MODE & 0xff000000
- orr r5, r5, #SELF_REFRESH_MODE & 0x000000ff
- str r5, [r4, #EMIFF_SDRAM_CONFIG_ASM_OFFSET & 0xff]
-
- @ prepare to put EMIFS to Sleep
- ldr r5, [r4, #EMIFS_CONFIG_ASM_OFFSET & 0xff]
- orr r5, r5, #IDLE_EMIFS_REQUEST & 0xff
- str r5, [r4, #EMIFS_CONFIG_ASM_OFFSET & 0xff]
-
- @ load base address of ARM_IDLECT1 and ARM_IDLECT2
- mov r4, #CLKGEN_REG_ASM_BASE & 0xff000000
- orr r4, r4, #CLKGEN_REG_ASM_BASE & 0x00ff0000
- orr r4, r4, #CLKGEN_REG_ASM_BASE & 0x0000ff00
-
- @ turn off clock domains
- mov r5, #OMAP1610_IDLE_CLOCK_DOMAINS & 0xff
- orr r5,r5, #OMAP1610_IDLE_CLOCK_DOMAINS & 0xff00
- strh r5, [r4, #ARM_IDLECT2_ASM_OFFSET & 0xff]
-
- @ work around errata of OMAP1610/5912. Enable (!) peripheral
- @ clock to let the chip go into deep sleep
- ldrh r5, [r4, #ARM_IDLECT2_ASM_OFFSET & 0xff]
- orr r5,r5, #EN_PERCK_BIT & 0xff
- strh r5, [r4, #ARM_IDLECT2_ASM_OFFSET & 0xff]
-
- @ request ARM idle
- mov r3, #OMAP1610_DEEP_SLEEP_REQUEST & 0xff
- orr r3, r3, #OMAP1610_DEEP_SLEEP_REQUEST & 0xff00
- strh r3, [r4, #ARM_IDLECT1_ASM_OFFSET & 0xff]
-
- mov r5, #IDLE_WAIT_CYCLES & 0xff
- orr r5, r5, #IDLE_WAIT_CYCLES & 0xff00
-l_1610_2:
- subs r5, r5, #1
- bne l_1610_2
-/*
- * Let's wait for the next wake up event to wake us up. r0 can't be
- * used here because r0 holds ARM_IDLECT1
- */
- mov r2, #0
- mcr p15, 0, r2, c7, c0, 4 @ wait for interrupt
-/*
- * omap1610_cpu_suspend()'s resume point.
- *
- * It will just start executing here, so we'll restore stuff from the
- * stack, reset the ARM_IDLECT1 and ARM_IDLECT2.
- */
- strh r1, [r4, #ARM_IDLECT2_ASM_OFFSET & 0xff]
- strh r0, [r4, #ARM_IDLECT1_ASM_OFFSET & 0xff]
-
- @ restore regs and return
- ldmfd sp!, {r0 - r12, pc}
-
-ENTRY(omap1610_cpu_suspend_sz)
- .word . - omap1610_cpu_suspend
-#endif /* CONFIG_ARCH_OMAP16XX */
+++ /dev/null
-/*
- * arch/arm/mach-omap/usb.c -- platform level USB initialization
- *
- * Copyright (C) 2004 Texas Instruments, Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- */
-
-#undef DEBUG
-
-#include <linux/config.h>
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/types.h>
-#include <linux/errno.h>
-#include <linux/init.h>
-#include <linux/device.h>
-#include <linux/usb_otg.h>
-
-#include <asm/io.h>
-#include <asm/irq.h>
-#include <asm/system.h>
-#include <asm/hardware.h>
-#include <asm/mach-types.h>
-
-#include <asm/arch/mux.h>
-#include <asm/arch/usb.h>
-#include <asm/arch/board.h>
-
-/* These routines should handle the standard chip-specific modes
- * for usb0/1/2 ports, covering basic mux and transceiver setup.
- *
- * Some board-*.c files will need to set up additional mux options,
- * like for suspend handling, vbus sensing, GPIOs, and the D+ pullup.
- */
-
-/* TESTED ON:
- * - 1611B H2 (with usb1 mini-AB) using standard Mini-B or OTG cables
- * - 5912 OSK OHCI (with usb0 standard-A), standard A-to-B cables
- * - 5912 OSK UDC, with *nonstandard* A-to-A cable
- * - 1510 Innovator UDC with bundled usb0 cable
- * - 1510 Innovator OHCI with bundled usb1/usb2 cable
- * - 1510 Innovator OHCI with custom usb0 cable, feeding 5V VBUS
- * - 1710 custom development board using alternate pin group
- * - 1710 H3 (with usb1 mini-AB) using standard Mini-B or OTG cables
- */
-
-/*-------------------------------------------------------------------------*/
-
-#ifdef CONFIG_ARCH_OMAP_OTG
-
-static struct otg_transceiver *xceiv;
-
-/**
- * otg_get_transceiver - find the (single) OTG transceiver driver
- *
- * Returns the transceiver driver, after getting a refcount to it; or
- * null if there is no such transceiver. The caller is responsible for
- * releasing that count.
- */
-struct otg_transceiver *otg_get_transceiver(void)
-{
- if (xceiv)
- get_device(xceiv->dev);
- return xceiv;
-}
-EXPORT_SYMBOL(otg_get_transceiver);
-
-int otg_set_transceiver(struct otg_transceiver *x)
-{
- if (xceiv && x)
- return -EBUSY;
- xceiv = x;
- return 0;
-}
-EXPORT_SYMBOL(otg_set_transceiver);
-
-#endif
-
-/*-------------------------------------------------------------------------*/
-
-static u32 __init omap_usb0_init(unsigned nwires, unsigned is_device)
-{
- u32 syscon1 = 0;
-
- if (nwires == 0) {
- if (!cpu_is_omap15xx()) {
- /* pulldown D+/D- */
- USB_TRANSCEIVER_CTRL_REG &= ~(3 << 1);
- }
- return 0;
- }
-
- if (is_device)
- omap_cfg_reg(W4_USB_PUEN);
-
- /* internal transceiver */
- if (nwires == 2) {
- // omap_cfg_reg(P9_USB_DP);
- // omap_cfg_reg(R8_USB_DM);
-
- if (cpu_is_omap15xx()) {
- /* This works on 1510-Innovator */
- return 0;
- }
-
- /* NOTES:
- * - peripheral should configure VBUS detection!
- * - only peripherals may use the internal D+/D- pulldowns
- * - OTG support on this port not yet written
- */
-
- USB_TRANSCEIVER_CTRL_REG &= ~(7 << 4);
- if (!is_device)
- USB_TRANSCEIVER_CTRL_REG |= (3 << 1);
-
- return 3 << 16;
- }
-
- /* alternate pin config, external transceiver */
- if (cpu_is_omap15xx()) {
- printk(KERN_ERR "no usb0 alt pin config on 15xx\n");
- return 0;
- }
-
- omap_cfg_reg(V6_USB0_TXD);
- omap_cfg_reg(W9_USB0_TXEN);
- omap_cfg_reg(W5_USB0_SE0);
-
- /* NOTE: SPEED and SUSP aren't configured here */
-
- if (nwires != 3)
- omap_cfg_reg(Y5_USB0_RCV);
- if (nwires != 6)
- USB_TRANSCEIVER_CTRL_REG &= ~CONF_USB2_UNI_R;
-
- switch (nwires) {
- case 3:
- syscon1 = 2;
- break;
- case 4:
- syscon1 = 1;
- break;
- case 6:
- syscon1 = 3;
- omap_cfg_reg(AA9_USB0_VP);
- omap_cfg_reg(R9_USB0_VM);
- USB_TRANSCEIVER_CTRL_REG |= CONF_USB2_UNI_R;
- break;
- default:
- printk(KERN_ERR "illegal usb%d %d-wire transceiver\n",
- 0, nwires);
- }
- return syscon1 << 16;
-}
-
-static u32 __init omap_usb1_init(unsigned nwires)
-{
- u32 syscon1 = 0;
-
- if (nwires != 6 && !cpu_is_omap15xx())
- USB_TRANSCEIVER_CTRL_REG &= ~CONF_USB1_UNI_R;
- if (nwires == 0)
- return 0;
-
- /* external transceiver */
- omap_cfg_reg(USB1_TXD);
- omap_cfg_reg(USB1_TXEN);
- if (cpu_is_omap15xx()) {
- omap_cfg_reg(USB1_SEO);
- omap_cfg_reg(USB1_SPEED);
- // SUSP
- } else if (cpu_is_omap1610() || cpu_is_omap5912()) {
- omap_cfg_reg(W13_1610_USB1_SE0);
- omap_cfg_reg(R13_1610_USB1_SPEED);
- // SUSP
- } else if (cpu_is_omap1710()) {
- omap_cfg_reg(R13_1710_USB1_SE0);
- // SUSP
- } else {
- pr_debug("usb unrecognized\n");
- }
- if (nwires != 3)
- omap_cfg_reg(USB1_RCV);
-
- switch (nwires) {
- case 3:
- syscon1 = 2;
- break;
- case 4:
- syscon1 = 1;
- break;
- case 6:
- syscon1 = 3;
- omap_cfg_reg(USB1_VP);
- omap_cfg_reg(USB1_VM);
- if (!cpu_is_omap15xx())
- USB_TRANSCEIVER_CTRL_REG |= CONF_USB1_UNI_R;
- break;
- default:
- printk(KERN_ERR "illegal usb%d %d-wire transceiver\n",
- 1, nwires);
- }
- return syscon1 << 20;
-}
-
-static u32 __init omap_usb2_init(unsigned nwires, unsigned alt_pingroup)
-{
- u32 syscon1 = 0;
-
- /* NOTE erratum: must leave USB2_UNI_R set if usb0 in use */
- if (alt_pingroup || nwires == 0)
- return 0;
- if (nwires != 6 && !cpu_is_omap15xx())
- USB_TRANSCEIVER_CTRL_REG &= ~CONF_USB2_UNI_R;
-
- /* external transceiver */
- if (cpu_is_omap15xx()) {
- omap_cfg_reg(USB2_TXD);
- omap_cfg_reg(USB2_TXEN);
- omap_cfg_reg(USB2_SEO);
- if (nwires != 3)
- omap_cfg_reg(USB2_RCV);
- /* there is no USB2_SPEED */
- } else if (cpu_is_omap16xx()) {
- omap_cfg_reg(V6_USB2_TXD);
- omap_cfg_reg(W9_USB2_TXEN);
- omap_cfg_reg(W5_USB2_SE0);
- if (nwires != 3)
- omap_cfg_reg(Y5_USB2_RCV);
- // FIXME omap_cfg_reg(USB2_SPEED);
- } else {
- pr_debug("usb unrecognized\n");
- }
- // omap_cfg_reg(USB2_SUSP);
-
- switch (nwires) {
- case 3:
- syscon1 = 2;
- break;
- case 4:
- syscon1 = 1;
- break;
- case 6:
- syscon1 = 3;
- if (cpu_is_omap15xx()) {
- omap_cfg_reg(USB2_VP);
- omap_cfg_reg(USB2_VM);
- } else {
- omap_cfg_reg(AA9_USB2_VP);
- omap_cfg_reg(R9_USB2_VM);
- USB_TRANSCEIVER_CTRL_REG |= CONF_USB2_UNI_R;
- }
- break;
- default:
- printk(KERN_ERR "illegal usb%d %d-wire transceiver\n",
- 2, nwires);
- }
- return syscon1 << 24;
-}
-
-/*-------------------------------------------------------------------------*/
-
-#if defined(CONFIG_USB_GADGET_OMAP) || \
- defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) || \
- (defined(CONFIG_USB_OTG) && defined(CONFIG_ARCH_OMAP_OTG))
-static void usb_release(struct device *dev)
-{
- /* normally not freed */
-}
-#endif
-
-#ifdef CONFIG_USB_GADGET_OMAP
-
-static struct resource udc_resources[] = {
- /* order is significant! */
- { /* registers */
- .start = UDC_BASE,
- .end = UDC_BASE + 0xff,
- .flags = IORESOURCE_MEM,
- }, { /* general IRQ */
- .start = IH2_BASE + 20,
- .flags = IORESOURCE_IRQ,
- }, { /* PIO IRQ */
- .start = IH2_BASE + 30,
- .flags = IORESOURCE_IRQ,
- }, { /* SOF IRQ */
- .start = IH2_BASE + 29,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static u64 udc_dmamask = ~(u32)0;
-
-static struct platform_device udc_device = {
- .name = "omap_udc",
- .id = -1,
- .dev = {
- .release = usb_release,
- .dma_mask = &udc_dmamask,
- .coherent_dma_mask = 0xffffffff,
- },
- .num_resources = ARRAY_SIZE(udc_resources),
- .resource = udc_resources,
-};
-
-#endif
-
-#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
-
-/* The dmamask must be set for OHCI to work */
-static u64 ohci_dmamask = ~(u32)0;
-
-static struct resource ohci_resources[] = {
- {
- .start = OMAP_OHCI_BASE,
- .end = OMAP_OHCI_BASE + 4096,
- .flags = IORESOURCE_MEM,
- },
- {
- .start = INT_USB_HHC_1,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device ohci_device = {
- .name = "ohci",
- .id = -1,
- .dev = {
- .release = usb_release,
- .dma_mask = &ohci_dmamask,
- .coherent_dma_mask = 0xffffffff,
- },
- .num_resources = ARRAY_SIZE(ohci_resources),
- .resource = ohci_resources,
-};
-
-#endif
-
-#if defined(CONFIG_USB_OTG) && defined(CONFIG_ARCH_OMAP_OTG)
-
-static struct resource otg_resources[] = {
- /* order is significant! */
- {
- .start = OTG_BASE,
- .end = OTG_BASE + 0xff,
- .flags = IORESOURCE_MEM,
- }, {
- .start = IH2_BASE + 8,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device otg_device = {
- .name = "omap_otg",
- .id = -1,
- .dev = {
- .release = usb_release,
- },
- .num_resources = ARRAY_SIZE(otg_resources),
- .resource = otg_resources,
-};
-
-#endif
-
-/*-------------------------------------------------------------------------*/
-
-#define ULPD_CLOCK_CTRL_REG __REG16(ULPD_CLOCK_CTRL)
-#define ULPD_SOFT_REQ_REG __REG16(ULPD_SOFT_REQ)
-
-
-// FIXME correct answer depends on hmc_mode,
-// as does any nonzero value for config->otg port number
-#ifdef CONFIG_USB_GADGET_OMAP
-#define is_usb0_device(config) 1
-#else
-#define is_usb0_device(config) 0
-#endif
-
-/*-------------------------------------------------------------------------*/
-
-#ifdef CONFIG_ARCH_OMAP_OTG
-
-void __init
-omap_otg_init(struct omap_usb_config *config)
-{
- u32 syscon = OTG_SYSCON_1_REG & 0xffff;
- int status;
- int alt_pingroup = 0;
-
- /* NOTE: no bus or clock setup (yet?) */
-
- syscon = OTG_SYSCON_1_REG & 0xffff;
- if (!(syscon & OTG_RESET_DONE))
- pr_debug("USB resets not complete?\n");
-
- // OTG_IRQ_EN_REG = 0;
-
- /* pin muxing and transceiver pinouts */
- if (config->pins[0] > 2) /* alt pingroup 2 */
- alt_pingroup = 1;
- syscon |= omap_usb0_init(config->pins[0], is_usb0_device(config));
- syscon |= omap_usb1_init(config->pins[1]);
- syscon |= omap_usb2_init(config->pins[2], alt_pingroup);
- pr_debug("OTG_SYSCON_1_REG = %08x\n", syscon);
- OTG_SYSCON_1_REG = syscon;
-
- syscon = config->hmc_mode;
- syscon |= USBX_SYNCHRO | (4 << 16) /* B_ASE0_BRST */;
-#ifdef CONFIG_USB_OTG
- if (config->otg)
- syscon |= OTG_EN;
-#endif
- pr_debug("USB_TRANSCEIVER_CTRL_REG = %03x\n", USB_TRANSCEIVER_CTRL_REG);
- pr_debug("OTG_SYSCON_2_REG = %08x\n", syscon);
- OTG_SYSCON_2_REG = syscon;
-
- printk("USB: hmc %d", config->hmc_mode);
- if (alt_pingroup)
- printk(", usb2 alt %d wires", config->pins[2]);
- else if (config->pins[0])
- printk(", usb0 %d wires%s", config->pins[0],
- is_usb0_device(config) ? " (dev)" : "");
- if (config->pins[1])
- printk(", usb1 %d wires", config->pins[1]);
- if (!alt_pingroup && config->pins[2])
- printk(", usb2 %d wires", config->pins[2]);
- if (config->otg)
- printk(", Mini-AB on usb%d", config->otg - 1);
- printk("\n");
-
- /* leave USB clocks/controllers off until needed */
- ULPD_SOFT_REQ_REG &= ~SOFT_USB_CLK_REQ;
- ULPD_CLOCK_CTRL_REG &= ~USB_MCLK_EN;
- ULPD_CLOCK_CTRL_REG |= DIS_USB_PVCI_CLK;
- syscon = OTG_SYSCON_1_REG;
- syscon |= HST_IDLE_EN|DEV_IDLE_EN|OTG_IDLE_EN;
-
-#ifdef CONFIG_USB_GADGET_OMAP
- if (config->otg || config->register_dev) {
- syscon &= ~DEV_IDLE_EN;
- udc_device.dev.platform_data = config;
- /* FIXME patch IRQ numbers for omap730 */
- status = platform_device_register(&udc_device);
- if (status)
- pr_debug("can't register UDC device, %d\n", status);
- }
-#endif
-
-#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
- if (config->otg || config->register_host) {
- syscon &= ~HST_IDLE_EN;
- ohci_device.dev.platform_data = config;
- if (cpu_is_omap730())
- ohci_resources[1].start = INT_730_USB_HHC_1;
- status = platform_device_register(&ohci_device);
- if (status)
- pr_debug("can't register OHCI device, %d\n", status);
- }
-#endif
-
-#ifdef CONFIG_USB_OTG
- if (config->otg) {
- syscon &= ~OTG_IDLE_EN;
- otg_device.dev.platform_data = config;
- if (cpu_is_omap730())
- otg_resources[1].start = INT_730_USB_OTG;
- status = platform_device_register(&otg_device);
- if (status)
- pr_debug("can't register OTG device, %d\n", status);
- }
-#endif
- pr_debug("OTG_SYSCON_1_REG = %08x\n", syscon);
- OTG_SYSCON_1_REG = syscon;
-
- status = 0;
-}
-
-#else
-static inline void omap_otg_init(struct omap_usb_config *config) {}
-#endif
-
-/*-------------------------------------------------------------------------*/
-
-#ifdef CONFIG_ARCH_OMAP1510
-
-#define ULPD_DPLL_CTRL_REG __REG16(ULPD_DPLL_CTRL)
-#define DPLL_IOB (1 << 13)
-#define DPLL_PLL_ENABLE (1 << 4)
-#define DPLL_LOCK (1 << 0)
-
-#define ULPD_APLL_CTRL_REG __REG16(ULPD_APLL_CTRL)
-#define APLL_NDPLL_SWITCH (1 << 0)
-
-
-static void __init omap_1510_usb_init(struct omap_usb_config *config)
-{
- int status;
- unsigned int val;
-
- omap_usb0_init(config->pins[0], is_usb0_device(config));
- omap_usb1_init(config->pins[1]);
- omap_usb2_init(config->pins[2], 0);
-
- val = omap_readl(MOD_CONF_CTRL_0) & ~(0x3f << 1);
- val |= (config->hmc_mode << 1);
- omap_writel(val, MOD_CONF_CTRL_0);
-
- printk("USB: hmc %d", config->hmc_mode);
- if (config->pins[0])
- printk(", usb0 %d wires%s", config->pins[0],
- is_usb0_device(config) ? " (dev)" : "");
- if (config->pins[1])
- printk(", usb1 %d wires", config->pins[1]);
- if (config->pins[2])
- printk(", usb2 %d wires", config->pins[2]);
- printk("\n");
-
- /* use DPLL for 48 MHz function clock */
- pr_debug("APLL %04x DPLL %04x REQ %04x\n", ULPD_APLL_CTRL_REG,
- ULPD_DPLL_CTRL_REG, ULPD_SOFT_REQ_REG);
- ULPD_APLL_CTRL_REG &= ~APLL_NDPLL_SWITCH;
- ULPD_DPLL_CTRL_REG |= DPLL_IOB | DPLL_PLL_ENABLE;
- ULPD_SOFT_REQ_REG |= SOFT_UDC_REQ | SOFT_DPLL_REQ;
- while (!(ULPD_DPLL_CTRL_REG & DPLL_LOCK))
- cpu_relax();
-
-#ifdef CONFIG_USB_GADGET_OMAP
- if (config->register_dev) {
- udc_device.dev.platform_data = config;
- status = platform_device_register(&udc_device);
- if (status)
- pr_debug("can't register UDC device, %d\n", status);
- /* udc driver gates 48MHz by D+ pullup */
- }
-#endif
-
-#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
- if (config->register_host) {
- ohci_device.dev.platform_data = config;
- status = platform_device_register(&ohci_device);
- if (status)
- pr_debug("can't register OHCI device, %d\n", status);
- /* hcd explicitly gates 48MHz */
- }
-#endif
-}
-
-#else
-static inline void omap_1510_usb_init(struct omap_usb_config *config) {}
-#endif
-
-/*-------------------------------------------------------------------------*/
-
-static struct omap_usb_config platform_data;
-
-static int __init
-omap_usb_init(void)
-{
- const struct omap_usb_config *config;
-
- config = omap_get_config(OMAP_TAG_USB, struct omap_usb_config);
- if (config == NULL) {
- printk(KERN_ERR "USB: No board-specific "
- "platform config found\n");
- return -ENODEV;
- }
- platform_data = *config;
-
- if (cpu_is_omap730() || cpu_is_omap16xx())
- omap_otg_init(&platform_data);
- else if (cpu_is_omap15xx())
- omap_1510_usb_init(&platform_data);
- else {
- printk(KERN_ERR "USB: No init for your chip yet\n");
- return -ENODEV;
- }
- return 0;
-}
-
-subsys_initcall(omap_usb_init);
projects / linux-2.6 / commitdiff