[ARM] 3407/1: lpd7x: documetation update

Patch from Marc Singer

New documentation for the touchscreen controllers and LCD panels.

Signed-off-by: Marc Singer <elf@buici.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

diff --git a/Documentation/arm/Sharp-LH/ADC-LH7-Touchscreen b/Documentation/arm/Sharp-LH/ADC-LH7-Touchscreen
new file mode 100644 (file)
index 0000000..1e6a23f
--- /dev/null
+++ b/Documentation/arm/Sharp-LH/ADC-LH7-Touchscreen
@@ -0,0 +1,61 @@
+README on the ADC/Touchscreen Controller
+========================================
+
+The LH79524 and LH7A404 include a built-in Analog to Digital
+controller (ADC) that is used to process input from a touchscreen.
+The driver only implements a four-wire touch panel protocol.
+
+The touchscreen driver is maintenance free except for the pen-down or
+touch threshold.  Some resistive displays and board combinations may
+require tuning of this threshold.  The driver exposes some of it's
+internal state in the sys filesystem.  If the kernel is configured
+with it, CONFIG_SYSFS, and sysfs is mounted at /sys, there will be a
+directory
+
+  /sys/devices/platform/adc-lh7.0
+
+containing these files.
+
+  -r--r--r--    1 root     root         4096 Jan  1 00:00 samples
+  -rw-r--r--    1 root     root         4096 Jan  1 00:00 threshold
+  -r--r--r--    1 root     root         4096 Jan  1 00:00 threshold_range
+
+The threshold is the current touch threshold.  It defaults to 750 on
+most targets.
+
+  # cat threshold
+ 750
+
+The threshold_range contains the range of valid values for the
+threshold.  Values outside of this range will be silently ignored.
+
+  # cat threshold_range
+  0 1023
+
+To change the threshold, write a value to the threshold file.
+
+  # echo 500 > threshold
+  # cat threshold
+  500
+
+The samples file contains the most recently sampled values from the
+ADC.  There are 12.  Below are typical of the last sampled values when
+the pen has been released.  The first two and last two samples are for
+detecting whether or not the pen is down.  The third through sixth are
+X coordinate samples.  The seventh through tenth are Y coordinate
+samples.
+
+  # cat samples
+  1023 1023 0 0 0 0 530 529 530 529 1023 1023
+
+To determine a reasonable threshold, press on the touch panel with an
+appropriate stylus and read the values from samples.
+
+  # cat samples
+  1023 676 92 103 101 102 855 919 922 922 1023 679
+
+The first and eleventh samples are discarded.  Thus, the important
+values are the second and twelfth which are used to determine if the
+pen is down.  When both are below the threshold, the driver registers
+that the pen is down.  When either is above the threshold, it
+registers then pen is up.

diff --git a/Documentation/arm/Sharp-LH/LCDPanels b/Documentation/arm/Sharp-LH/LCDPanels
new file mode 100644 (file)
index 0000000..fb1b21c
--- /dev/null
+++ b/Documentation/arm/Sharp-LH/LCDPanels
@@ -0,0 +1,59 @@
+README on the LCD Panels
+========================
+
+Configuration options for several LCD panels, available from Logic PD,
+are included in the kernel source.  This README will help you
+understand the configuration data and give you some guidance for
+adding support for other panels if you wish.
+
+
+lcd-panels.h
+------------
+
+There is no way, at present, to detect which panel is attached to the
+system at runtime.  Thus the kernel configuration is static.  The file
+arch/arm/mach-ld7a40x/lcd-panels.h (or similar) defines all of the
+panel specific parameters.
+
+It should be possible for this data to be shared among several device
+families.  The current layout may be insufficiently general, but it is
+amenable to improvement.
+
+
+PIXEL_CLOCK
+-----------
+
+The panel data sheets will give a range of acceptable pixel clocks.
+The fundamental LCDCLK input frequency is divided down by a PCD
+constant in field '.tim2'.  It may happen that it is impossible to set
+the pixel clock within this range.  A clock which is too slow will
+tend to flicker.  For the highest quality image, set the clock as high
+as possible.
+
+
+MARGINS
+-------
+
+These values may be difficult to glean from the panel data sheet.  In
+the case of the Sharp panels, the upper margin is explicitly called
+out as a specific number of lines from the top of the frame.  The
+other values may not matter as much as the panels tend to
+automatically center the image.
+
+
+Sync Sense
+----------
+
+The sense of the hsync and vsync pulses may be called out in the data
+sheet.  On one panel, the sense of these pulses determine the height
+of the visible region on the panel.  Most of the Sharp panels use
+negative sense sync pulses set by the TIM2_IHS and TIM2_IVS bits in
+'.tim2'.
+
+
+Pel Layout
+----------
+
+The Sharp color TFT panels are all configured for 16 bit direct color
+modes.  The amba-lcd driver sets the pel mode to 565 for 5 bits of
+each red and blue and 6 bits of green.