/* CPLD doesn't have ack capability, but some devices may */
#if defined (CPLD_INTMASK_TOUCH)
- /* The touch control *must* mask the the interrupt because the
+ /* The touch control *must* mask the interrupt because the
* interrupt bit is read by the driver to determine if the pen
* is still down. */
if (irq == IRQ_TOUCH)
depends on ACPI
default n
---help---
- This enables the the kernel to boot on EFI platforms using
+ This enables the kernel to boot on EFI platforms using
system configuration information passed to it from the firmware.
This also enables the kernel to use any EFI runtime services that are
available (such as the EFI variable services).
* We pretend to bring them out of full D3 state, and restore the proper
* IRQ, PCI cache line size, and BARs, otherwise the device won't function
* properly. In some cases, the device will generate an interrupt on
- * the wrong IRQ line, causing any devices sharing the the line it's
+ * the wrong IRQ line, causing any devices sharing the line it's
* *supposed* to use to be disabled by the kernel's IRQ debug code.
*/
static u16 toshiba_line_size;
skb_put(skb, (msg->size - msg->leadin_ignore - msg->tailout_ignore));
/*
- * Move the data over from the the other side.
+ * Move the data over from the other side.
*/
if ((XPNET_VERSION_MINOR(msg->version) == 1) &&
(msg->embedded_bytes != 0)) {
hex "Address of the base of system vectors"
default "0"
help
- Define the address of the the system vectors. Commonly this is
+ Define the address of the system vectors. Commonly this is
put at the start of RAM, but it doesn't have to be. On ColdFire
platforms this address is programmed into the VBR register, thus
actually setting the address to use.
* Overflow check: For the 64bit handler, we need at least one
* free instruction slot for the wrap-around branch. In worst
* case, if the intended insertion point is a delay slot, we
- * need three, with the the second nop'ed and the third being
+ * need three, with the second nop'ed and the third being
* unused.
*/
#ifdef CONFIG_32BIT
* to "proper" values now (otherwise we'll wind up restoring
* whatever was last stored in the task structure, which might
* be inconsistent if an interrupt occured while on the gateway
- * page) Note that we may be "trashing" values the user put in
- * them, but we don't support the the user changing them.
+ * page). Note that we may be "trashing" values the user put in
+ * them, but we don't support the user changing them.
*/
STREG %r0,PT_SR2(%r16)
depends on ADVANCED_OPTIONS && NOT_COHERENT_CACHE
help
This option allows you to set the base virtual address
- of the the consistent memory pool. This pool of virtual
+ of the consistent memory pool. This pool of virtual
memory is used to make consistent memory allocations.
config CONSISTENT_START
bool "Set custom consistent memory pool size"
depends on ADVANCED_OPTIONS && NOT_COHERENT_CACHE
help
- This option allows you to set the size of the the
+ This option allows you to set the size of the
consistent memory pool. This pool of virtual memory
is used to make consistent memory allocations.
depends on ADVANCED_OPTIONS && NOT_COHERENT_CACHE
help
This option allows you to set the base virtual address
- of the the consistent memory pool. This pool of virtual
+ of the consistent memory pool. This pool of virtual
memory is used to make consistent memory allocations.
config CONSISTENT_START
bool "Set custom consistent memory pool size"
depends on ADVANCED_OPTIONS && NOT_COHERENT_CACHE
help
- This option allows you to set the size of the the
+ This option allows you to set the size of the
consistent memory pool. This pool of virtual memory
is used to make consistent memory allocations.
define archhelp
echo '* linux - Binary kernel image (./linux) - for backward'
echo ' compatibility only, this creates a hard link to the'
- echo ' real kernel binary, the the "vmlinux" binary you'
+ echo ' real kernel binary, the "vmlinux" binary you'
echo ' find in the kernel root.'
endef
}
/* Common setup code for both startup command line and mconsole initialization.
- * @lines contains the the array (of size @num) to modify;
+ * @lines contains the array (of size @num) to modify;
* @init is the setup string;
*/
#define PTRACE_OLDSETOPTIONS 21
#endif
-/* These are before the system call, so the the system call number is RAX
+/* These are before the system call, so the system call number is RAX
* rather than ORIG_RAX, and arg4 is R10 rather than RCX
*/
#define REGS_SYSCALL_NR PT_INDEX(RAX)
sst.w lp, PTO+PT_GPR(GPR_LP)[ep]; \
type ## _STATE_SAVER
/* Pop a register state pushed by PUSH_STATE, except for the stack pointer,
- from the the stack. */
+ from the stack. */
#define POP_STATE(type) \
mov sp, ep; \
type ## _STATE_RESTORER; \
*
* DO NOT COMBINE this function with <arch/xtensa/lib/hal/memcopy.S>.
* It needs to remain separate and distinct. The hal files are part
- * of the the Xtensa link-time HAL, and those files may differ per
+ * of the Xtensa link-time HAL, and those files may differ per
* processor configuration. Patching the kernel for another
* processor configuration includes replacing the hal files, and we
- * could loose the special functionality for accessing user-space
+ * could lose the special functionality for accessing user-space
* memory during such a patch. We sacrifice a little code space here
* in favor to simplify code maintenance.
*
projects / linux-2.6 / commitdiff