#define USB_PID_WINFAST_DTV_DONGLE_COLD 0x6025
#define USB_PID_WINFAST_DTV_DONGLE_WARM 0x6026
#define USB_PID_WINFAST_DTV_DONGLE_STK7700P 0x6f00
-#define USB_PID_GENPIX_8PSK_COLD 0x0200
-#define USB_PID_GENPIX_8PSK_WARM 0x0201
+#define USB_PID_GENPIX_8PSK_REV_1_COLD 0x0200
+#define USB_PID_GENPIX_8PSK_REV_1_WARM 0x0201
+#define USB_PID_GENPIX_8PSK_REV_2 0x0202
+#define USB_PID_GENPIX_SKYWALKER_1 0x0203
+#define USB_PID_GENPIX_SKYWALKER_CW3K 0x0204
#define USB_PID_SIGMATEK_DVB_110 0x6610
#define USB_PID_MSI_DIGI_VOX_MINI_II 0x1513
#define USB_PID_OPERA1_COLD 0x2830
/* DVB USB compliant Linux driver for the
- * - GENPIX 8pks/qpsk USB2.0 DVB-S module
+ * - GENPIX 8pks/qpsk/DCII USB2.0 DVB-S module
*
- * Copyright (C) 2006 Alan Nisota (alannisota@gmail.com)
+ * Copyright (C) 2006,2007 Alan Nisota (alannisota@gmail.com)
+ * Copyright (C) 2006,2007 Genpix Electronics (genpix@genpix-electronics.com)
*
* Thanks to GENPIX for the sample code used to implement this module.
*
struct gp8psk_fe_state {
struct dvb_frontend fe;
-
struct dvb_usb_device *d;
-
+ u8 lock;
u16 snr;
-
- unsigned long next_snr_check;
+ unsigned long next_status_check;
+ unsigned long status_check_interval;
};
+static int gp8psk_fe_update_status(struct gp8psk_fe_state *st)
+{
+ u8 buf[6];
+ if (time_after(jiffies,st->next_status_check)) {
+ gp8psk_usb_in_op(st->d, GET_SIGNAL_LOCK, 0,0,&st->lock,1);
+ gp8psk_usb_in_op(st->d, GET_SIGNAL_STRENGTH, 0,0,buf,6);
+ st->snr = (buf[1]) << 8 | buf[0];
+ st->next_status_check = jiffies + (st->status_check_interval*HZ)/1000;
+ }
+ return 0;
+}
+
static int gp8psk_fe_read_status(struct dvb_frontend* fe, fe_status_t *status)
{
struct gp8psk_fe_state *st = fe->demodulator_priv;
- u8 lock;
+ gp8psk_fe_update_status(st);
- if (gp8psk_usb_in_op(st->d, GET_SIGNAL_LOCK, 0, 0, &lock,1))
- return -EINVAL;
-
- if (lock)
+ if (st->lock)
*status = FE_HAS_LOCK | FE_HAS_SYNC | FE_HAS_VITERBI | FE_HAS_SIGNAL | FE_HAS_CARRIER;
else
*status = 0;
+ if (*status & FE_HAS_LOCK)
+ st->status_check_interval = 1000;
+ else
+ st->status_check_interval = 100;
return 0;
}
static int gp8psk_fe_read_snr(struct dvb_frontend* fe, u16 *snr)
{
struct gp8psk_fe_state *st = fe->demodulator_priv;
- u8 buf[2];
-
- if (time_after(jiffies,st->next_snr_check)) {
- gp8psk_usb_in_op(st->d,GET_SIGNAL_STRENGTH,0,0,buf,2);
- *snr = (int)(buf[1]) << 8 | buf[0];
- /* snr is reported in dBu*256 */
- /* snr / 38.4 ~= 100% strength */
- /* snr * 17 returns 100% strength as 65535 */
- if (*snr <= 3855)
- *snr = (*snr<<4) + *snr; // snr * 17
- else
- *snr = 65535;
- st->next_snr_check = jiffies + (10*HZ)/1000;
- } else {
- *snr = st->snr;
- }
+ gp8psk_fe_update_status(st);
+ /* snr is reported in dBu*256 */
+ *snr = st->snr;
return 0;
}
static int gp8psk_fe_read_signal_strength(struct dvb_frontend* fe, u16 *strength)
{
- return gp8psk_fe_read_snr(fe, strength);
+ struct gp8psk_fe_state *st = fe->demodulator_priv;
+ gp8psk_fe_update_status(st);
+ /* snr is reported in dBu*256 */
+ /* snr / 38.4 ~= 100% strength */
+ /* snr * 17 returns 100% strength as 65535 */
+ if (st->snr > 0xf00)
+ *strength = 0xffff;
+ else
+ *strength = (st->snr << 4) + st->snr; /* snr*17 */
+ return 0;
}
static int gp8psk_fe_get_tune_settings(struct dvb_frontend* fe, struct dvb_frontend_tune_settings *tune)
{
- tune->min_delay_ms = 800;
+ tune->min_delay_ms = 200;
return 0;
}
gp8psk_usb_out_op(state->d,TUNE_8PSK,0,0,cmd,10);
- state->next_snr_check = jiffies;
+ state->lock = 0;
+ state->next_status_check = jiffies;
+ state->status_check_interval = 200;
return 0;
}
return 0;
}
+static int gp8psk_fe_enable_high_lnb_voltage(struct dvb_frontend* fe, long onoff)
+{
+ struct gp8psk_fe_state* state = fe->demodulator_priv;
+ return gp8psk_usb_out_op(state->d, USE_EXTRA_VOLT, onoff, 0,NULL,0);
+}
+
static int gp8psk_fe_send_legacy_dish_cmd (struct dvb_frontend* fe, unsigned long sw_cmd)
{
struct gp8psk_fe_state* state = fe->demodulator_priv;
static struct dvb_frontend_ops gp8psk_fe_ops = {
.info = {
- .name = "Genpix 8psk-USB DVB-S",
+ .name = "Genpix 8psk-to-USB2 DVB-S",
.type = FE_QPSK,
- .frequency_min = 950000,
- .frequency_max = 2150000,
+ .frequency_min = 800000,
+ .frequency_max = 2250000,
.frequency_stepsize = 100,
.symbol_rate_min = 1000000,
.symbol_rate_max = 45000000,
.set_tone = gp8psk_fe_set_tone,
.set_voltage = gp8psk_fe_set_voltage,
.dishnetwork_send_legacy_command = gp8psk_fe_send_legacy_dish_cmd,
+ .enable_high_lnb_voltage = gp8psk_fe_enable_high_lnb_voltage
};
/* DVB USB compliant Linux driver for the
- * - GENPIX 8pks/qpsk USB2.0 DVB-S module
+ * - GENPIX 8pks/qpsk/DCII USB2.0 DVB-S module
*
- * Copyright (C) 2006 Alan Nisota (alannisota@gmail.com)
+ * Copyright (C) 2006,2007 Alan Nisota (alannisota@gmail.com)
+ * Copyright (C) 2006,2007 Genpix Electronics (genpix@genpix-electronics.com)
*
* Thanks to GENPIX for the sample code used to implement this module.
*
}
if (ret < 0 || ret != blen) {
- warn("usb in operation failed.");
+ warn("usb in %d operation failed.", req);
ret = -EIO;
} else
ret = 0;
if (gp8psk_usb_out_op(d, LOAD_BCM4500,1,0,NULL, 0))
goto out_rel_fw;
- info("downloaidng bcm4500 firmware from file '%s'",bcm4500_firmware);
+ info("downloading bcm4500 firmware from file '%s'",bcm4500_firmware);
ptr = fw->data;
- buf = kmalloc(512, GFP_KERNEL | GFP_DMA);
+ buf = kmalloc(64, GFP_KERNEL | GFP_DMA);
while (ptr[0] != 0xff) {
u16 buflen = ptr[0] + 4;
static int gp8psk_power_ctrl(struct dvb_usb_device *d, int onoff)
{
u8 status, buf;
+ int gp_product_id = le16_to_cpu(d->udev->descriptor.idProduct);
+
if (onoff) {
gp8psk_usb_in_op(d, GET_8PSK_CONFIG,0,0,&status,1);
- if (! (status & 0x01)) /* started */
+ if (! (status & bm8pskStarted)) { /* started */
+ if(gp_product_id == USB_PID_GENPIX_SKYWALKER_CW3K)
+ gp8psk_usb_out_op(d, CW3K_INIT, 1, 0, NULL, 0);
if (gp8psk_usb_in_op(d, BOOT_8PSK, 1, 0, &buf, 1))
return -EINVAL;
+ }
- if (! (status & 0x02)) /* BCM4500 firmware loaded */
- if(gp8psk_load_bcm4500fw(d))
- return EINVAL;
+ if (gp_product_id == USB_PID_GENPIX_8PSK_REV_1_WARM)
+ if (! (status & bm8pskFW_Loaded)) /* BCM4500 firmware loaded */
+ if(gp8psk_load_bcm4500fw(d))
+ return EINVAL;
- if (! (status & 0x04)) /* LNB Power */
+ if (! (status & bmIntersilOn)) /* LNB Power */
if (gp8psk_usb_in_op(d, START_INTERSIL, 1, 0,
&buf, 1))
return EINVAL;
- /* Set DVB mode */
- if(gp8psk_usb_out_op(d, SET_DVB_MODE, 1, 0, NULL, 0))
- return -EINVAL;
- gp8psk_usb_in_op(d, GET_8PSK_CONFIG,0,0,&status,1);
+ /* Set DVB mode to 1 */
+ if (gp_product_id == USB_PID_GENPIX_8PSK_REV_1_WARM)
+ if (gp8psk_usb_out_op(d, SET_DVB_MODE, 1, 0, NULL, 0))
+ return EINVAL;
+ /* Abort possible TS (if previous tune crashed) */
+ if (gp8psk_usb_out_op(d, ARM_TRANSFER, 0, 0, NULL, 0))
+ return EINVAL;
} else {
/* Turn off LNB power */
if (gp8psk_usb_in_op(d, START_INTERSIL, 0, 0, &buf, 1))
/* Turn off 8psk power */
if (gp8psk_usb_in_op(d, BOOT_8PSK, 0, 0, &buf, 1))
return -EINVAL;
-
+ if(gp_product_id == USB_PID_GENPIX_SKYWALKER_CW3K)
+ gp8psk_usb_out_op(d, CW3K_INIT, 0, 0, NULL, 0);
}
return 0;
}
+int gp8psk_bcm4500_reload(struct dvb_usb_device *d)
+{
+ u8 buf;
+ int gp_product_id = le16_to_cpu(d->udev->descriptor.idProduct);
+ /* Turn off 8psk power */
+ if (gp8psk_usb_in_op(d, BOOT_8PSK, 0, 0, &buf, 1))
+ return -EINVAL;
+ /* Turn On 8psk power */
+ if (gp8psk_usb_in_op(d, BOOT_8PSK, 1, 0, &buf, 1))
+ return -EINVAL;
+ /* load BCM4500 firmware */
+ if (gp_product_id == USB_PID_GENPIX_8PSK_REV_1_WARM)
+ if (gp8psk_load_bcm4500fw(d))
+ return EINVAL;
+ return 0;
+}
static int gp8psk_streaming_ctrl(struct dvb_usb_adapter *adap, int onoff)
{
static int gp8psk_usb_probe(struct usb_interface *intf,
const struct usb_device_id *id)
{
- return dvb_usb_device_init(intf,&gp8psk_properties,THIS_MODULE,NULL);
+ int ret;
+ struct usb_device *udev = interface_to_usbdev(intf);
+ ret = dvb_usb_device_init(intf,&gp8psk_properties,THIS_MODULE,NULL);
+ if (ret == 0) {
+ info("found Genpix USB device pID = %x (hex)",
+ le16_to_cpu(udev->descriptor.idProduct));
+ }
+ return ret;
}
static struct usb_device_id gp8psk_usb_table [] = {
- { USB_DEVICE(USB_VID_GENPIX, USB_PID_GENPIX_8PSK_COLD) },
- { USB_DEVICE(USB_VID_GENPIX, USB_PID_GENPIX_8PSK_WARM) },
+ { USB_DEVICE(USB_VID_GENPIX, USB_PID_GENPIX_8PSK_REV_1_COLD) },
+ { USB_DEVICE(USB_VID_GENPIX, USB_PID_GENPIX_8PSK_REV_1_WARM) },
+ { USB_DEVICE(USB_VID_GENPIX, USB_PID_GENPIX_8PSK_REV_2) },
+ { USB_DEVICE(USB_VID_GENPIX, USB_PID_GENPIX_SKYWALKER_1) },
+ { USB_DEVICE(USB_VID_GENPIX, USB_PID_GENPIX_SKYWALKER_CW3K) },
{ 0 },
};
MODULE_DEVICE_TABLE(usb, gp8psk_usb_table);
.generic_bulk_ctrl_endpoint = 0x01,
- .num_device_descs = 1,
+ .num_device_descs = 4,
.devices = {
- { .name = "Genpix 8PSK-USB DVB-S USB2.0 receiver",
+ { .name = "Genpix 8PSK-to-USB2 Rev.1 DVB-S receiver",
.cold_ids = { &gp8psk_usb_table[0], NULL },
.warm_ids = { &gp8psk_usb_table[1], NULL },
},
+ { .name = "Genpix 8PSK-to-USB2 Rev.2 DVB-S receiver",
+ .cold_ids = { NULL },
+ .warm_ids = { &gp8psk_usb_table[2], NULL },
+ },
+ { .name = "Genpix SkyWalker-1 DVB-S receiver",
+ .cold_ids = { NULL },
+ .warm_ids = { &gp8psk_usb_table[3], NULL },
+ },
+ { .name = "Genpix SkyWalker-CW3K DVB-S receiver",
+ .cold_ids = { NULL },
+ .warm_ids = { &gp8psk_usb_table[4], NULL },
+ },
{ NULL },
}
};
module_exit(gp8psk_usb_module_exit);
MODULE_AUTHOR("Alan Nisota <alannisota@gamil.com>");
-MODULE_DESCRIPTION("Driver for Genpix 8psk-USB DVB-S USB2.0");
-MODULE_VERSION("1.0");
+MODULE_DESCRIPTION("Driver for Genpix 8psk-to-USB2 DVB-S");
+MODULE_VERSION("1.1");
MODULE_LICENSE("GPL");
/* DVB USB compliant Linux driver for the
- * - GENPIX 8pks/qpsk USB2.0 DVB-S module
+ * - GENPIX 8pks/qpsk/DCII USB2.0 DVB-S module
*
* Copyright (C) 2006 Alan Nisota (alannisota@gmail.com)
+ * Copyright (C) 2006,2007 Alan Nisota (alannisota@gmail.com)
*
* Thanks to GENPIX for the sample code used to implement this module.
*
#define TH_COMMAND_IN 0xC0
#define TH_COMMAND_OUT 0xC1
-/* command bytes */
-#define GET_8PSK_CONFIG 0x80
+/* gp8psk commands */
+
+#define GET_8PSK_CONFIG 0x80 /* in */
#define SET_8PSK_CONFIG 0x81
+#define I2C_WRITE 0x83
+#define I2C_READ 0x84
#define ARM_TRANSFER 0x85
#define TUNE_8PSK 0x86
-#define GET_SIGNAL_STRENGTH 0x87
+#define GET_SIGNAL_STRENGTH 0x87 /* in */
#define LOAD_BCM4500 0x88
-#define BOOT_8PSK 0x89
-#define START_INTERSIL 0x8A
+#define BOOT_8PSK 0x89 /* in */
+#define START_INTERSIL 0x8A /* in */
#define SET_LNB_VOLTAGE 0x8B
#define SET_22KHZ_TONE 0x8C
#define SEND_DISEQC_COMMAND 0x8D
#define SET_DVB_MODE 0x8E
#define SET_DN_SWITCH 0x8F
-#define GET_SIGNAL_LOCK 0x90
+#define GET_SIGNAL_LOCK 0x90 /* in */
+#define GET_SERIAL_NUMBER 0x93 /* in */
+#define USE_EXTRA_VOLT 0x94
+#define CW3K_INIT 0x9d
+
+/* PSK_configuration bits */
+#define bm8pskStarted 0x01
+#define bm8pskFW_Loaded 0x02
+#define bmIntersilOn 0x04
+#define bmDVBmode 0x08
+#define bm22kHz 0x10
+#define bmSEL18V 0x20
+#define bmDCtuned 0x40
+#define bmArmed 0x80
/* Satellite modulation modes */
#define ADV_MOD_DVB_QPSK 0 /* DVB-S QPSK */
extern int gp8psk_usb_in_op(struct dvb_usb_device *d, u8 req, u16 value, u16 index, u8 *b, int blen);
extern int gp8psk_usb_out_op(struct dvb_usb_device *d, u8 req, u16 value,
u16 index, u8 *b, int blen);
+extern int gp8psk_bcm4500_reload(struct dvb_usb_device *d);
#endif
projects / linux-2.6 / commitdiff