#include <asm/arch/board.h>
#include <asm/arch/common.h>
#include <asm/arch/gpmc.h>
-#include "prcm-regs.h"
#include <asm/io.h>
int eth_cs;
unsigned long cs_mem_base;
unsigned int rate;
- struct clk *l3ck;
+ struct clk *gpmc_fck;
eth_cs = SDP2430_SMC91X_CS;
- l3ck = clk_get(NULL, "core_l3_ck");
- if (IS_ERR(l3ck))
- rate = 100000000;
- else
- rate = clk_get_rate(l3ck);
+ gpmc_fck = clk_get(NULL, "gpmc_fck"); /* Always on ENABLE_ON_INIT */
+ if (IS_ERR(gpmc_fck)) {
+ WARN_ON(1);
+ return;
+ }
+
+ clk_enable(gpmc_fck);
+ rate = clk_get_rate(gpmc_fck);
/* Make sure CS1 timings are correct, for 2430 always muxed */
gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG1, 0x00011200);
if (gpmc_cs_request(eth_cs, SZ_16M, &cs_mem_base) < 0) {
printk(KERN_ERR "Failed to request GPMC mem for smc91x\n");
- return;
+ goto out;
}
sdp2430_smc91x_resources[0].start = cs_mem_base + 0x300;
printk(KERN_ERR "Failed to request GPIO%d for smc91x IRQ\n",
OMAP24XX_ETHR_GPIO_IRQ);
gpmc_cs_free(eth_cs);
- return;
+ goto out;
}
omap_set_gpio_direction(OMAP24XX_ETHR_GPIO_IRQ, 1);
+out:
+ clk_disable(gpmc_fck);
+ clk_put(gpmc_fck);
}
static void __init omap_2430sdp_init_irq(void)
#include <linux/interrupt.h>
#include <linux/delay.h>
#include <linux/leds.h>
+#include <linux/err.h>
+#include <linux/clk.h>
#include <asm/hardware.h>
#include <asm/mach-types.h>
#include <asm/arch/board.h>
#include <asm/arch/common.h>
#include <asm/arch/gpmc.h>
-#include "prcm-regs.h"
+#include <asm/arch/control.h>
/* LED & Switch macros */
#define LED0_GPIO13 13
{
unsigned long base;
+ unsigned int rate;
+ struct clk *gpmc_fck;
+ int eth_cs;
+
+ gpmc_fck = clk_get(NULL, "gpmc_fck"); /* Always on ENABLE_ON_INIT */
+ if (IS_ERR(gpmc_fck)) {
+ WARN_ON(1);
+ return;
+ }
+
+ clk_enable(gpmc_fck);
+ rate = clk_get_rate(gpmc_fck);
+
+ eth_cs = APOLLON_ETH_CS;
+
/* Make sure CS1 timings are correct */
- GPMC_CONFIG1_1 = 0x00011203;
- GPMC_CONFIG2_1 = 0x001f1f01;
- GPMC_CONFIG3_1 = 0x00080803;
- GPMC_CONFIG4_1 = 0x1c091c09;
- GPMC_CONFIG5_1 = 0x041f1f1f;
- GPMC_CONFIG6_1 = 0x000004c4;
+ gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG1, 0x00011200);
+
+ if (rate >= 160000000) {
+ gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG2, 0x001f1f01);
+ gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG3, 0x00080803);
+ gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG4, 0x1c0b1c0a);
+ gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG5, 0x041f1F1F);
+ gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG6, 0x000004C4);
+ } else if (rate >= 130000000) {
+ gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG2, 0x001f1f00);
+ gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG3, 0x00080802);
+ gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG4, 0x1C091C09);
+ gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG5, 0x041f1F1F);
+ gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG6, 0x000004C4);
+ } else {/* rate = 100000000 */
+ gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG2, 0x001f1f00);
+ gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG3, 0x00080802);
+ gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG4, 0x1C091C09);
+ gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG5, 0x031A1F1F);
+ gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG6, 0x000003C2);
+ }
if (gpmc_cs_request(APOLLON_ETH_CS, SZ_16M, &base) < 0) {
printk(KERN_ERR "Failed to request GPMC CS for smc91x\n");
- return;
+ goto out;
}
apollon_smc91x_resources[0].start = base + 0x300;
apollon_smc91x_resources[0].end = base + 0x30f;
printk(KERN_ERR "Failed to request GPIO%d for smc91x IRQ\n",
APOLLON_ETHR_GPIO_IRQ);
gpmc_cs_free(APOLLON_ETH_CS);
- return;
+ goto out;
}
omap_set_gpio_direction(APOLLON_ETHR_GPIO_IRQ, 1);
+
+out:
+ clk_disable(gpmc_fck);
+ clk_put(gpmc_fck);
}
static void __init omap_apollon_init_irq(void)
static void __init omap_apollon_init(void)
{
+ u32 v;
+
apollon_led_init();
apollon_sw_init();
apollon_flash_init();
omap_cfg_reg(W19_24XX_SYS_NIRQ);
/* Use Interal loop-back in MMC/SDIO Module Input Clock selection */
- CONTROL_DEVCONF |= (1 << 24);
+ v = omap_ctrl_readl(OMAP2_CONTROL_DEVCONF0);
+ v |= (1 << 24);
+ omap_ctrl_writel(v, OMAP2_CONTROL_DEVCONF0);
/*
* Make sure the serial ports are muxed on at this point.
#include <linux/delay.h>
#include <linux/workqueue.h>
#include <linux/input.h>
+#include <linux/err.h>
+#include <linux/clk.h>
#include <asm/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/map.h>
#include <asm/mach/flash.h>
+#include <asm/arch/control.h>
#include <asm/arch/gpio.h>
#include <asm/arch/gpioexpander.h>
#include <asm/arch/mux.h>
#include <asm/arch/keypad.h>
#include <asm/arch/menelaus.h>
#include <asm/arch/dma.h>
-#include "prcm-regs.h"
+#include <asm/arch/gpmc.h>
#include <asm/io.h>
+#define H4_FLASH_CS 0
+#define H4_SMC91X_CS 1
+
static unsigned int row_gpios[6] = { 88, 89, 124, 11, 6, 96 };
static unsigned int col_gpios[7] = { 90, 91, 100, 36, 12, 97, 98 };
};
static struct resource h4_flash_resource = {
- .start = H4_CS0_BASE,
- .end = H4_CS0_BASE + SZ_64M - 1,
.flags = IORESOURCE_MEM,
};
&h4_lcd_device,
};
+/* 2420 Sysboot setup (2430 is different) */
+static u32 get_sysboot_value(void)
+{
+ return (omap_ctrl_readl(OMAP24XX_CONTROL_STATUS) &
+ (OMAP2_SYSBOOT_5_MASK | OMAP2_SYSBOOT_4_MASK |
+ OMAP2_SYSBOOT_3_MASK | OMAP2_SYSBOOT_2_MASK |
+ OMAP2_SYSBOOT_1_MASK | OMAP2_SYSBOOT_0_MASK));
+}
+
+/* H4-2420's always used muxed mode, H4-2422's always use non-muxed
+ *
+ * Note: OMAP-GIT doesn't correctly do is_cpu_omap2422 and is_cpu_omap2423
+ * correctly. The macro needs to look at production_id not just hawkeye.
+ */
+static u32 is_gpmc_muxed(void)
+{
+ u32 mux;
+ mux = get_sysboot_value();
+ if ((mux & 0xF) == 0xd)
+ return 1; /* NAND config (could be either) */
+ if (mux & 0x2) /* if mux'ed */
+ return 1;
+ else
+ return 0;
+}
+
static inline void __init h4_init_debug(void)
{
+ int eth_cs;
+ unsigned long cs_mem_base;
+ unsigned int muxed, rate;
+ struct clk *gpmc_fck;
+
+ eth_cs = H4_SMC91X_CS;
+
+ gpmc_fck = clk_get(NULL, "gpmc_fck"); /* Always on ENABLE_ON_INIT */
+ if (IS_ERR(gpmc_fck)) {
+ WARN_ON(1);
+ return;
+ }
+
+ clk_enable(gpmc_fck);
+ rate = clk_get_rate(gpmc_fck);
+ clk_disable(gpmc_fck);
+ clk_put(gpmc_fck);
+
+ if (is_gpmc_muxed())
+ muxed = 0x200;
+ else
+ muxed = 0;
+
/* Make sure CS1 timings are correct */
- GPMC_CONFIG1_1 = 0x00011200;
- GPMC_CONFIG2_1 = 0x001f1f01;
- GPMC_CONFIG3_1 = 0x00080803;
- GPMC_CONFIG4_1 = 0x1c091c09;
- GPMC_CONFIG5_1 = 0x041f1f1f;
- GPMC_CONFIG6_1 = 0x000004c4;
- GPMC_CONFIG7_1 = 0x00000f40 | (0x08000000 >> 24);
+ gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG1,
+ 0x00011000 | muxed);
+
+ if (rate >= 160000000) {
+ gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG2, 0x001f1f01);
+ gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG3, 0x00080803);
+ gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG4, 0x1c0b1c0a);
+ gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG5, 0x041f1F1F);
+ gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG6, 0x000004C4);
+ } else if (rate >= 130000000) {
+ gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG2, 0x001f1f00);
+ gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG3, 0x00080802);
+ gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG4, 0x1C091C09);
+ gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG5, 0x041f1F1F);
+ gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG6, 0x000004C4);
+ } else {/* rate = 100000000 */
+ gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG2, 0x001f1f00);
+ gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG3, 0x00080802);
+ gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG4, 0x1C091C09);
+ gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG5, 0x031A1F1F);
+ gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG6, 0x000003C2);
+ }
+
+ if (gpmc_cs_request(eth_cs, SZ_16M, &cs_mem_base) < 0) {
+ printk(KERN_ERR "Failed to request GPMC mem for smc91x\n");
+ goto out;
+ }
+
udelay(100);
omap_cfg_reg(M15_24XX_GPIO92);
if (debug_card_init(cs_mem_base, OMAP24XX_ETHR_GPIO_IRQ) < 0)
gpmc_cs_free(eth_cs);
+
+out:
+ clk_disable(gpmc_fck);
+ clk_put(gpmc_fck);
+}
+
+static void __init h4_init_flash(void)
+{
+ unsigned long base;
+
+ if (gpmc_cs_request(H4_FLASH_CS, SZ_64M, &base) < 0) {
+ printk("Can't request GPMC CS for flash\n");
+ return;
+ }
+ h4_flash_resource.start = base;
+ h4_flash_resource.end = base + SZ_64M - 1;
}
static void __init omap_h4_init_irq(void)
omap2_init_common_hw();
omap_init_irq();
omap_gpio_init();
+ h4_init_flash();
}
static struct omap_uart_config h4_uart_config __initdata = {
static void __iomem *gpmc_cs_base =
(void __iomem *) IO_ADDRESS(GPMC_BASE) + GPMC_CS0;
-static struct clk *gpmc_l3_clk;
+static struct clk *gpmc_fck;
static void gpmc_write_reg(int idx, u32 val)
{
return __raw_readl(gpmc_cs_base + (cs * GPMC_CS_SIZE) + idx);
}
-/* TODO: Add support for gpmc_fck to clock framework and use it */
unsigned long gpmc_get_fclk_period(void)
{
/* In picoseconds */
- return 1000000000 / ((clk_get_rate(gpmc_l3_clk)) / 1000);
+ return 1000000000 / ((clk_get_rate(gpmc_fck)) / 1000);
}
unsigned int gpmc_ns_to_ticks(unsigned int time_ns)
{
u32 l;
- gpmc_l3_clk = clk_get(NULL, "core_l3_ck");
- BUG_ON(IS_ERR(gpmc_l3_clk));
+ gpmc_fck = clk_get(NULL, "gpmc_fck"); /* Always on ENABLE_ON_INIT */
+ if (IS_ERR(gpmc_fck))
+ WARN_ON(1);
+ else
+ clk_enable(gpmc_fck);
l = gpmc_read_reg(GPMC_REVISION);
printk(KERN_INFO "GPMC revision %d.%d\n", (l >> 4) & 0x0f, l & 0x0f);
#include <asm/arch/clock.h>
#include <asm/arch/sram.h>
-#include "prcm-regs.h"
+#include "prm.h"
+
#include "memory.h"
+#include "sdrc.h"
+unsigned long omap2_sdrc_base;
+unsigned long omap2_sms_base;
static struct memory_timings mem_timings;
+static u32 curr_perf_level = CORE_CLK_SRC_DPLL_X2;
u32 omap2_memory_get_slow_dll_ctrl(void)
{
unsigned long dll_cnt;
u32 fast_dll = 0;
- mem_timings.m_type = !((SDRC_MR_0 & 0x3) == 0x1); /* DDR = 1, SDR = 0 */
+ mem_timings.m_type = !((sdrc_read_reg(SDRC_MR_0) & 0x3) == 0x1); /* DDR = 1, SDR = 0 */
/* 2422 es2.05 and beyond has a single SIP DDR instead of 2 like others.
* In the case of 2422, its ok to use CS1 instead of CS0.
mem_timings.dll_mode = M_LOCK;
if (mem_timings.base_cs == 0) {
- fast_dll = SDRC_DLLA_CTRL;
- dll_cnt = SDRC_DLLA_STATUS & 0xff00;
+ fast_dll = sdrc_read_reg(SDRC_DLLA_CTRL);
+ dll_cnt = sdrc_read_reg(SDRC_DLLA_STATUS) & 0xff00;
} else {
- fast_dll = SDRC_DLLB_CTRL;
- dll_cnt = SDRC_DLLB_STATUS & 0xff00;
+ fast_dll = sdrc_read_reg(SDRC_DLLB_CTRL);
+ dll_cnt = sdrc_read_reg(SDRC_DLLB_STATUS) & 0xff00;
}
if (force_lock_to_unlock_mode) {
fast_dll &= ~0xff00;
{
u32 l;
- l = SMS_SYSCONFIG;
+ l = sms_read_reg(SMS_SYSCONFIG);
l &= ~(0x3 << 3);
l |= (0x2 << 3);
- SMS_SYSCONFIG = l;
+ sms_write_reg(l, SMS_SYSCONFIG);
- l = SDRC_SYSCONFIG;
+ l = sdrc_read_reg(SDRC_SYSCONFIG);
l &= ~(0x3 << 3);
l |= (0x2 << 3);
- SDRC_SYSCONFIG = l;
-
+ sdrc_write_reg(l, SDRC_SYSCONFIG);
}
#include <asm/io.h>
#include <linux/spinlock.h>
+#include <asm/arch/control.h>
#include <asm/arch/mux.h>
#ifdef CONFIG_OMAP_MUX
#define OMAP24XX_PINS_SZ 0
#endif /* CONFIG_ARCH_OMAP24XX */
-#define OMAP24XX_L4_BASE 0x48000000
#define OMAP24XX_PULL_ENA (1 << 3)
#define OMAP24XX_PULL_UP (1 << 4)
-/* REVISIT: Convert this code to use ctrl_{read,write}_reg */
#if defined(CONFIG_OMAP_MUX_DEBUG) || defined(CONFIG_OMAP_MUX_WARNINGS)
void __init_or_module omap2_cfg_debug(const struct pin_config *cfg, u8 reg)
{
u16 orig;
u8 warn = 0, debug = 0;
- orig = omap_readb(OMAP24XX_L4_BASE + cfg->mux_reg);
+ orig = omap_ctrl_readb(cfg->mux_reg);
#ifdef CONFIG_OMAP_MUX_DEBUG
debug = cfg->debug;
if (debug || warn)
printk(KERN_WARNING
"MUX: setup %s (0x%08x): 0x%02x -> 0x%02x\n",
- cfg->name, omap_readb(OMAP24XX_L4_BASE + cfg->mux_reg));
+ cfg->name, omap_ctrl_base_get() + cfg->mux_reg,
+ orig, reg);
}
#else
#define omap2_cfg_debug(x, y) do {} while (0)
if (cfg->pu_pd_val)
reg |= OMAP24XX_PULL_UP;
omap2_cfg_debug(cfg, reg);
- omap_writeb(reg, OMAP24XX_L4_BASE + cfg->mux_reg);
+ omap_ctrl_writeb(reg, cfg->mux_reg);
spin_unlock_irqrestore(&mux_spin_lock, flags);
return 0;
#ifndef __ARCH_ARM_MACH_OMAP2_PRCM_H
#define __ARCH_ARM_MACH_OMAP2_PRCM_H
+#ifdef CONFIG_ARCH_OMAP2420
+#define OMAP24XX_32KSYNCT_BASE (L4_24XX_BASE + 0x4000)
+#define OMAP24XX_PRCM_BASE (L4_24XX_BASE + 0x8000)
+#define OMAP24XX_SDRC_BASE (L3_24XX_BASE + 0x9000)
+#define OMAP242X_CONTROL_STATUS (L4_24XX_BASE + 0x2f8)
+#endif
+
+#ifdef CONFIG_ARCH_OMAP2430
+#define OMAP24XX_32KSYNCT_BASE (L4_WK_243X_BASE + 0x20000)
+#define OMAP24XX_PRCM_BASE (L4_WK_243X_BASE + 0x6000)
+#define OMAP24XX_SDRC_BASE (0x6D000000)
+#define OMAP242X_CONTROL_STATUS (L4_24XX_BASE + 0x2f8)
+#endif
+
/* SET_PERFORMANCE_LEVEL PARAMETERS */
#define PRCM_HALF_SPEED 1
#define PRCM_FULL_SPEED 2
#include <linux/init.h>
#include <linux/clk.h>
-#include "prcm-regs.h"
+#include <asm/io.h>
+
+#include "prm.h"
+#include "prm-regbits-24xx.h"
extern void omap2_clk_prepare_for_reboot(void);
u32 omap_prcm_get_reset_sources(void)
{
- return RM_RSTST_WKUP & 0x7f;
+ return prm_read_mod_reg(WKUP_MOD, RM_RSTST) & 0x7f;
}
EXPORT_SYMBOL(omap_prcm_get_reset_sources);
/* Resets clock rates and reboots the system. Only called from system.h */
void omap_prcm_arch_reset(char mode)
{
+ u32 wkup;
omap2_clk_prepare_for_reboot();
- RM_RSTCTRL_WKUP |= 2;
+
+ if (cpu_is_omap24xx()) {
+ wkup = prm_read_mod_reg(WKUP_MOD, RM_RSTCTRL) | OMAP_RST_DPLL3;
+ prm_write_mod_reg(wkup, WKUP_MOD, RM_RSTCTRL);
+ }
}
#include <asm/arch/io.h>
#include <asm/arch/pm.h>
-#define A_32KSYNC_CR_V IO_ADDRESS(OMAP_TIMER32K_BASE+0x10)
-#define A_PRCM_VOLTCTRL_V IO_ADDRESS(OMAP24XX_PRCM_BASE+0x50)
-#define A_PRCM_CLKCFG_CTRL_V IO_ADDRESS(OMAP24XX_PRCM_BASE+0x80)
-#define A_CM_CLKEN_PLL_V IO_ADDRESS(OMAP24XX_PRCM_BASE+0x500)
-#define A_CM_IDLEST_CKGEN_V IO_ADDRESS(OMAP24XX_PRCM_BASE+0x520)
-#define A_CM_CLKSEL1_PLL_V IO_ADDRESS(OMAP24XX_PRCM_BASE+0x540)
-#define A_CM_CLKSEL2_PLL_V IO_ADDRESS(OMAP24XX_PRCM_BASE+0x544)
+#include "sdrc.h"
-#define A_SDRC_DLLA_CTRL_V IO_ADDRESS(OMAP24XX_SDRC_BASE+0x60)
-#define A_SDRC_POWER_V IO_ADDRESS(OMAP24XX_SDRC_BASE+0x70)
-#define A_SDRC_RFR_CTRL_V IO_ADDRESS(OMAP24XX_SDRC_BASE+0xA4)
+/* First address of reserved address space? apparently valid for OMAP2 & 3 */
#define A_SDRC0_V (0xC0000000)
-#define A_SDRC_MANUAL_V IO_ADDRESS(OMAP24XX_SDRC_BASE+0xA8)
.text
ldmfd sp!, {r0 - r12, pc} @ restore regs and return
A_SDRC_POWER:
- .word A_SDRC_POWER_V
+ .word OMAP242X_SDRC_REGADDR(SDRC_POWER)
A_SDRC0:
.word A_SDRC0_V
-A_CM_CLKSEL2_PLL_S:
- .word A_CM_CLKSEL2_PLL_V
-A_CM_CLKEN_PLL:
- .word A_CM_CLKEN_PLL_V
A_SDRC_DLLA_CTRL_S:
- .word A_SDRC_DLLA_CTRL_V
-A_SDRC_MANUAL_S:
- .word A_SDRC_MANUAL_V
+ .word OMAP242X_SDRC_REGADDR(SDRC_DLLA_CTRL)
ENTRY(omap24xx_cpu_suspend_sz)
.word . - omap24xx_cpu_suspend
#include <asm/arch/io.h>
#include <asm/hardware.h>
-#include "prcm-regs.h"
+#include "sdrc.h"
+#include "prm.h"
+#include "cm.h"
-#define TIMER_32KSYNCT_CR_V IO_ADDRESS(OMAP24XX_32KSYNCT_BASE + 0x010)
-
-#define CM_CLKSEL2_PLL_V IO_ADDRESS(OMAP24XX_PRCM_BASE + 0x544)
-#define PRCM_VOLTCTRL_V IO_ADDRESS(OMAP24XX_PRCM_BASE + 0x050)
-#define PRCM_CLKCFG_CTRL_V IO_ADDRESS(OMAP24XX_PRCM_BASE + 0x080)
-#define CM_CLKEN_PLL_V IO_ADDRESS(OMAP24XX_PRCM_BASE + 0x500)
-#define CM_IDLEST_CKGEN_V IO_ADDRESS(OMAP24XX_PRCM_BASE + 0x520)
-#define CM_CLKSEL1_PLL_V IO_ADDRESS(OMAP24XX_PRCM_BASE + 0x540)
-
-#define SDRC_DLLA_CTRL_V IO_ADDRESS(OMAP24XX_SDRC_BASE + 0x060)
-#define SDRC_RFR_CTRL_V IO_ADDRESS(OMAP24XX_SDRC_BASE + 0x0a4)
+#define TIMER_32KSYNCT_CR_V IO_ADDRESS(OMAP2420_32KSYNCT_BASE + 0x010)
.text
/* relative load constants */
cm_clksel2_pll:
- .word CM_CLKSEL2_PLL_V
+ .word OMAP2420_CM_REGADDR(PLL_MOD, CM_CLKSEL2)
sdrc_dlla_ctrl:
- .word SDRC_DLLA_CTRL_V
+ .word OMAP242X_SDRC_REGADDR(SDRC_DLLA_CTRL)
prcm_voltctrl:
- .word PRCM_VOLTCTRL_V
+ .word OMAP2420_PRM_REGADDR(OCP_MOD, 0x50)
prcm_mask_val:
.word 0xFFFF3FFC
timer_32ksynct_cr:
mov pc, lr @ back to caller
ddr_cm_clksel2_pll:
- .word CM_CLKSEL2_PLL_V
+ .word OMAP2420_CM_REGADDR(PLL_MOD, CM_CLKSEL2)
ddr_sdrc_dlla_ctrl:
- .word SDRC_DLLA_CTRL_V
+ .word OMAP242X_SDRC_REGADDR(SDRC_DLLA_CTRL)
ddr_sdrc_rfr_ctrl:
- .word SDRC_RFR_CTRL_V
+ .word OMAP242X_SDRC_REGADDR(SDRC_RFR_CTRL_0)
ddr_prcm_voltctrl:
- .word PRCM_VOLTCTRL_V
+ .word OMAP2420_PRM_REGADDR(OCP_MOD, 0x50)
ddr_prcm_mask_val:
.word 0xFFFF3FFC
ddr_timer_32ksynct:
ldmfd sp!, {r0-r12, pc} @ restore regs and return
set_config:
- .word PRCM_CLKCFG_CTRL_V
+ .word OMAP2420_PRM_REGADDR(OCP_MOD, 0x80)
pll_ctl:
- .word CM_CLKEN_PLL_V
+ .word OMAP2420_CM_REGADDR(PLL_MOD, CM_FCLKEN1)
pll_stat:
- .word CM_IDLEST_CKGEN_V
+ .word OMAP2420_CM_REGADDR(PLL_MOD, CM_IDLEST1)
pll_div:
- .word CM_CLKSEL1_PLL_V
+ .word OMAP2420_CM_REGADDR(PLL_MOD, CM_CLKSEL)
sdrc_rfr:
- .word SDRC_RFR_CTRL_V
+ .word OMAP242X_SDRC_REGADDR(SDRC_RFR_CTRL_0)
dlla_ctrl:
- .word SDRC_DLLA_CTRL_V
+ .word OMAP242X_SDRC_REGADDR(SDRC_DLLA_CTRL)
ENTRY(sram_set_prcm_sz)
.word . - sram_set_prcm
#include <asm/setup.h>
#include <asm/arch/board.h>
+#include <asm/arch/control.h>
#include <asm/arch/mux.h>
#include <asm/arch/fpga.h>
#include <asm/arch/clock.h>
+#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3)
+# include "../mach-omap2/sdrc.h"
+#endif
+
#define NO_LENGTH_CHECK 0xffffffff
unsigned char omap_bootloader_tag[512];
#if defined(CONFIG_ARCH_OMAP16XX)
#define TIMER_32K_SYNCHRONIZED 0xfffbc410
-#elif defined(CONFIG_ARCH_OMAP24XX)
-#define TIMER_32K_SYNCHRONIZED (OMAP24XX_32KSYNCT_BASE + 0x10)
+#elif defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX)
+#define TIMER_32K_SYNCHRONIZED (OMAP2_32KSYNCT_BASE + 0x10)
#endif
#ifdef TIMER_32K_SYNCHRONIZED
static char err[] __initdata = KERN_ERR
"%s: can't register clocksource!\n";
- if (cpu_is_omap16xx() || cpu_is_omap24xx()) {
+ if (cpu_is_omap16xx() || cpu_class_is_omap2()) {
+ struct clk *sync_32k_ick;
+
+ sync_32k_ick = clk_get(NULL, "omap_32ksync_ick");
+ if (sync_32k_ick)
+ clk_enable(sync_32k_ick);
+
clocksource_32k.mult = clocksource_hz2mult(32768,
clocksource_32k.shift);
arch_initcall(omap_init_clocksource_32k);
#endif /* TIMER_32K_SYNCHRONIZED */
+
+/* Global address base setup code */
+
+#if defined(CONFIG_ARCH_OMAP2420)
+void __init omap2_set_globals_242x(void)
+{
+ omap2_sdrc_base = OMAP2420_SDRC_BASE;
+ omap2_sms_base = OMAP2420_SMS_BASE;
+ omap_ctrl_base_set(OMAP2420_CTRL_BASE);
+}
+#endif
+
+#if defined(CONFIG_ARCH_OMAP2430)
+void __init omap2_set_globals_243x(void)
+{
+ omap2_sdrc_base = OMAP243X_SDRC_BASE;
+ omap2_sms_base = OMAP243X_SMS_BASE;
+ omap_ctrl_base_set(OMAP243X_CTRL_BASE);
+}
+#endif
+
+#if defined(CONFIG_ARCH_OMAP3430)
+void __init omap2_set_globals_343x(void)
+{
+ omap2_sdrc_base = OMAP343X_SDRC_BASE;
+ omap2_sms_base = OMAP343X_SMS_BASE;
+ omap_ctrl_base_set(OMAP343X_CTRL_BASE);
+}
+#endif
+
#define CLOCK_IN_OMAP242X (1 << 25)
#define CLOCK_IN_OMAP243X (1 << 26)
+/* CM_CLKSEL2_PLL.CORE_CLK_SRC options (24XX) */
+#define CORE_CLK_SRC_32K 0
+#define CORE_CLK_SRC_DPLL 1
+#define CORE_CLK_SRC_DPLL_X2 2
+
#endif
.endm
.macro get_irqnr_and_base, irqnr, irqstat, base, tmp
- ldr \base, =VA_IC_BASE
+ ldr \base, =OMAP2_VA_IC_BASE
ldr \irqnr, [\base, #0x98] /* IRQ pending reg 1 */
cmp \irqnr, #0x0
bne 2222f
#define OMAP243X_GPMC_PHYS OMAP243X_GPMC_BASE /* 0x49000000 */
#define OMAP243X_GPMC_VIRT 0xFE000000
#define OMAP243X_GPMC_SIZE SZ_1M
+#define OMAP243X_SDRC_PHYS OMAP243X_SDRC_BASE
+#define OMAP243X_SDRC_VIRT 0xFD000000
+#define OMAP243X_SDRC_SIZE SZ_1M
+#define OMAP243X_SMS_PHYS OMAP243X_SMS_BASE
+#define OMAP243X_SMS_VIRT 0xFC000000
+#define OMAP243X_SMS_SIZE SZ_1M
+
#endif
#define IO_OFFSET 0x90000000
#define io_v2p(va) ((va) - IO_OFFSET) /* Works for L3 and L4 */
/* DSP */
-#define DSP_MEM_24XX_PHYS OMAP24XX_DSP_MEM_BASE /* 0x58000000 */
+#define DSP_MEM_24XX_PHYS OMAP2420_DSP_MEM_BASE /* 0x58000000 */
#define DSP_MEM_24XX_VIRT 0xe0000000
#define DSP_MEM_24XX_SIZE 0x28000
-#define DSP_IPI_24XX_PHYS OMAP24XX_DSP_IPI_BASE /* 0x59000000 */
+#define DSP_IPI_24XX_PHYS OMAP2420_DSP_IPI_BASE /* 0x59000000 */
#define DSP_IPI_24XX_VIRT 0xe1000000
#define DSP_IPI_24XX_SIZE SZ_4K
-#define DSP_MMU_24XX_PHYS OMAP24XX_DSP_MMU_BASE /* 0x5a000000 */
+#define DSP_MMU_24XX_PHYS OMAP2420_DSP_MMU_BASE /* 0x5a000000 */
#define DSP_MMU_24XX_VIRT 0xe2000000
#define DSP_MMU_24XX_SIZE SZ_4K
+#elif defined(CONFIG_ARCH_OMAP3)
+
+/* We map both L3 and L4 on OMAP3 */
+#define L3_34XX_PHYS L3_34XX_BASE /* 0x68000000 */
+#define L3_34XX_VIRT 0xf8000000
+#define L3_34XX_SIZE SZ_1M /* 44kB of 128MB used, want 1MB sect */
+
+#define L4_34XX_PHYS L4_34XX_BASE /* 0x48000000 */
+#define L4_34XX_VIRT 0xd8000000
+#define L4_34XX_SIZE SZ_4M /* 1MB of 128MB used, want 1MB sect */
+
+/*
+ * Need to look at the Size 4M for L4.
+ * VPOM3430 was not working for Int controller
+ */
+
+#define L4_WK_34XX_PHYS L4_WK_34XX_BASE /* 0x48300000 */
+#define L4_WK_34XX_VIRT 0xd8300000
+#define L4_WK_34XX_SIZE SZ_1M
+
+#define L4_PER_34XX_PHYS L4_PER_34XX_BASE /* 0x49000000 */
+#define L4_PER_34XX_VIRT 0xd9000000
+#define L4_PER_34XX_SIZE SZ_1M
+
+#define L4_EMU_34XX_PHYS L4_EMU_34XX_BASE /* 0x54000000 */
+#define L4_EMU_34XX_VIRT 0xe4000000
+#define L4_EMU_34XX_SIZE SZ_64M
+
+#define OMAP34XX_GPMC_PHYS OMAP34XX_GPMC_BASE /* 0x6E000000 */
+#define OMAP34XX_GPMC_VIRT 0xFE000000
+#define OMAP34XX_GPMC_SIZE SZ_1M
+
+#define OMAP343X_SMS_PHYS OMAP343X_SMS_BASE /* 0x6C000000 */
+#define OMAP343X_SMS_VIRT 0xFC000000
+#define OMAP343X_SMS_SIZE SZ_1M
+
+#define OMAP343X_SDRC_PHYS OMAP343X_SDRC_BASE /* 0x6D000000 */
+#define OMAP343X_SDRC_VIRT 0xFD000000
+#define OMAP343X_SDRC_SIZE SZ_1M
+
+
+#define IO_OFFSET 0x90000000
+#define IO_ADDRESS(pa) ((pa) + IO_OFFSET)/* Works for L3 and L4 */
+#define io_p2v(pa) ((pa) + IO_OFFSET)/* Works for L3 and L4 */
+#define io_v2p(va) ((va) - IO_OFFSET)/* Works for L3 and L4 */
+
+/* DSP */
+#define DSP_MEM_34XX_PHYS OMAP34XX_DSP_MEM_BASE /* 0x58000000 */
+#define DSP_MEM_34XX_VIRT 0xe0000000
+#define DSP_MEM_34XX_SIZE 0x28000
+#define DSP_IPI_34XX_PHYS OMAP34XX_DSP_IPI_BASE /* 0x59000000 */
+#define DSP_IPI_34XX_VIRT 0xe1000000
+#define DSP_IPI_34XX_SIZE SZ_4K
+#define DSP_MMU_34XX_PHYS OMAP34XX_DSP_MMU_BASE /* 0x5a000000 */
+#define DSP_MMU_34XX_VIRT 0xe2000000
+#define DSP_MMU_34XX_SIZE SZ_4K
+
#endif
#ifndef __ASSEMBLER__
+/*
+ * include/asm-arm/arch-omap/omap24xx.h
+ *
+ * This file contains the processor specific definitions
+ * of the TI OMAP24XX.
+ *
+ * Copyright (C) 2007 Texas Instruments.
+ * Copyright (C) 2007 Nokia Corporation.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ */
+
#ifndef __ASM_ARCH_OMAP24XX_H
#define __ASM_ARCH_OMAP24XX_H
/* interrupt controller */
#define OMAP24XX_IC_BASE (L4_24XX_BASE + 0xfe000)
-#define VA_IC_BASE IO_ADDRESS(OMAP24XX_IC_BASE)
#define OMAP24XX_IVA_INTC_BASE 0x40000000
#define IRQ_SIR_IRQ 0x0040
-#ifdef CONFIG_ARCH_OMAP2420
-#define OMAP24XX_32KSYNCT_BASE (L4_24XX_BASE + 0x4000)
-#define OMAP24XX_PRCM_BASE (L4_24XX_BASE + 0x8000)
-#define OMAP24XX_SDRC_BASE (L3_24XX_BASE + 0x9000)
-#define OMAP242X_CONTROL_STATUS (L4_24XX_BASE + 0x2f8)
-#endif
+#define OMAP2420_CTRL_BASE L4_24XX_BASE
+#define OMAP2420_32KSYNCT_BASE (L4_24XX_BASE + 0x4000)
+#define OMAP2420_PRCM_BASE (L4_24XX_BASE + 0x8000)
+#define OMAP2420_CM_BASE (L4_24XX_BASE + 0x8000)
+#define OMAP2420_PRM_BASE OMAP2420_CM_BASE
+#define OMAP2420_SDRC_BASE (L3_24XX_BASE + 0x9000)
+#define OMAP2420_SMS_BASE 0x68008000
-#ifdef CONFIG_ARCH_OMAP2430
-#define OMAP24XX_32KSYNCT_BASE (L4_WK_243X_BASE + 0x20000)
-#define OMAP24XX_PRCM_BASE (L4_WK_243X_BASE + 0x6000)
-#define OMAP24XX_SDRC_BASE (0x6D000000)
-#define OMAP242X_CONTROL_STATUS (L4_24XX_BASE + 0x2f8)
+#define OMAP2430_32KSYNCT_BASE (L4_WK_243X_BASE + 0x20000)
+#define OMAP2430_PRCM_BASE (L4_WK_243X_BASE + 0x6000)
+#define OMAP2430_CM_BASE (L4_WK_243X_BASE + 0x6000)
+#define OMAP2430_PRM_BASE OMAP2430_CM_BASE
+
+#define OMAP243X_SMS_BASE 0x6C000000
+#define OMAP243X_SDRC_BASE 0x6D000000
#define OMAP243X_GPMC_BASE 0x6E000000
-#endif
+#define OMAP243X_SCM_BASE (L4_WK_243X_BASE + 0x2000)
+#define OMAP243X_CTRL_BASE OMAP243X_SCM_BASE
+#define OMAP243X_HS_BASE (L4_24XX_BASE + 0x000ac000)
/* DSP SS */
-#define OMAP24XX_DSP_BASE 0x58000000
-#define OMAP24XX_DSP_MEM_BASE (OMAP24XX_DSP_BASE + 0x0)
-#define OMAP24XX_DSP_IPI_BASE (OMAP24XX_DSP_BASE + 0x1000000)
-#define OMAP24XX_DSP_MMU_BASE (OMAP24XX_DSP_BASE + 0x2000000)
+#define OMAP2420_DSP_BASE 0x58000000
+#define OMAP2420_DSP_MEM_BASE (OMAP2420_DSP_BASE + 0x0)
+#define OMAP2420_DSP_IPI_BASE (OMAP2420_DSP_BASE + 0x1000000)
+#define OMAP2420_DSP_MMU_BASE (OMAP2420_DSP_BASE + 0x2000000)
+
+#define OMAP243X_DSP_BASE 0x5C000000
+#define OMAP243X_DSP_MEM_BASE (OMAP243X_DSP_BASE + 0x0)
+#define OMAP243X_DSP_MMU_BASE (OMAP243X_DSP_BASE + 0x1000000)
/* Mailbox */
#define OMAP24XX_MAILBOX_BASE (L4_24XX_BASE + 0x94000)
+/* Camera */
+#define OMAP24XX_CAMERA_BASE (L4_24XX_BASE + 0x52000)
+
+/* Security */
+#define OMAP24XX_SEC_BASE (L4_24XX_BASE + 0xA0000)
+#define OMAP24XX_SEC_RNG_BASE (OMAP24XX_SEC_BASE + 0x0000)
+#define OMAP24XX_SEC_DES_BASE (OMAP24XX_SEC_BASE + 0x2000)
+#define OMAP24XX_SEC_SHA1MD5_BASE (OMAP24XX_SEC_BASE + 0x4000)
+#define OMAP24XX_SEC_AES_BASE (OMAP24XX_SEC_BASE + 0x6000)
+#define OMAP24XX_SEC_PKA_BASE (OMAP24XX_SEC_BASE + 0x8000)
+
+#if defined(CONFIG_ARCH_OMAP2420)
+
+#define OMAP2_32KSYNCT_BASE OMAP2420_32KSYNCT_BASE
+#define OMAP2_PRCM_BASE OMAP2420_PRCM_BASE
+#define OMAP2_CM_BASE OMAP2420_CM_BASE
+#define OMAP2_PRM_BASE OMAP2420_PRM_BASE
+#define OMAP2_VA_IC_BASE IO_ADDRESS(OMAP24XX_IC_BASE)
+
+#elif defined(CONFIG_ARCH_OMAP2430)
+
+#define OMAP2_32KSYNCT_BASE OMAP2430_32KSYNCT_BASE
+#define OMAP2_PRCM_BASE OMAP2430_PRCM_BASE
+#define OMAP2_CM_BASE OMAP2430_CM_BASE
+#define OMAP2_PRM_BASE OMAP2430_PRM_BASE
+#define OMAP2_VA_IC_BASE IO_ADDRESS(OMAP24XX_IC_BASE)
+
+#endif
+
#endif /* __ASM_ARCH_OMAP24XX_H */
projects / linux-2.6 / commitdiff