* DCD. However, the pin multiplexing aren't changed and should be set either
* by the bootloader or in the platform init code.
*
- * The idx field must be equal to the PSC index ( e.g. 0 for PSC1, 1 for PSC2,
+ * The idx field must be equal to the PSC index (e.g. 0 for PSC1, 1 for PSC2,
* and so on). So the PSC1 is mapped to /dev/ttyPSC0, PSC2 to /dev/ttyPSC1 and
* so on. But be warned, it's an ABSOLUTE REQUIREMENT ! This is needed mainly
* fpr the console code : without this 1:1 mapping, at early boot time, when we
#include <linux/sysrq.h>
#include <linux/console.h>
-#include <asm/delay.h>
-#include <asm/io.h>
+#include <linux/delay.h>
+#include <linux/io.h>
#if defined(CONFIG_PPC_MERGE)
#include <linux/of.h>
/* Forward declaration of the interruption handling routine */
-static irqreturn_t mpc52xx_uart_int(int irq,void *dev_id);
+static irqreturn_t mpc52xx_uart_int(int irq, void *dev_id);
/* Simple macro to test if a port is console or not. This one is taken
* for serial_core.c and maybe should be moved to serial_core.h ? */
#ifdef CONFIG_SERIAL_CORE_CONSOLE
-#define uart_console(port) ((port)->cons && (port)->cons->index == (port)->line)
+#define uart_console(port) \
+ ((port)->cons && (port)->cons->index == (port)->line)
#else
#define uart_console(port) (0)
#endif
{
/* port->lock taken by caller */
port->read_status_mask &= ~MPC52xx_PSC_IMR_TXRDY;
- out_be16(&PSC(port)->mpc52xx_psc_imr,port->read_status_mask);
+ out_be16(&PSC(port)->mpc52xx_psc_imr, port->read_status_mask);
}
static void
{
/* port->lock taken by caller */
port->read_status_mask |= MPC52xx_PSC_IMR_TXRDY;
- out_be16(&PSC(port)->mpc52xx_psc_imr,port->read_status_mask);
+ out_be16(&PSC(port)->mpc52xx_psc_imr, port->read_status_mask);
}
static void
/* Make sure tx interrupts are on */
/* Truly necessary ??? They should be anyway */
port->read_status_mask |= MPC52xx_PSC_IMR_TXRDY;
- out_be16(&PSC(port)->mpc52xx_psc_imr,port->read_status_mask);
+ out_be16(&PSC(port)->mpc52xx_psc_imr, port->read_status_mask);
}
spin_unlock_irqrestore(&port->lock, flags);
{
/* port->lock taken by caller */
port->read_status_mask &= ~MPC52xx_PSC_IMR_RXRDY;
- out_be16(&PSC(port)->mpc52xx_psc_imr,port->read_status_mask);
+ out_be16(&PSC(port)->mpc52xx_psc_imr, port->read_status_mask);
}
static void
unsigned long flags;
spin_lock_irqsave(&port->lock, flags);
- if ( ctl == -1 )
- out_8(&PSC(port)->command,MPC52xx_PSC_START_BRK);
+ if (ctl == -1)
+ out_8(&PSC(port)->command, MPC52xx_PSC_START_BRK);
else
- out_8(&PSC(port)->command,MPC52xx_PSC_STOP_BRK);
+ out_8(&PSC(port)->command, MPC52xx_PSC_STOP_BRK);
spin_unlock_irqrestore(&port->lock, flags);
}
return ret;
/* Reset/activate the port, clear and enable interrupts */
- out_8(&psc->command,MPC52xx_PSC_RST_RX);
- out_8(&psc->command,MPC52xx_PSC_RST_TX);
+ out_8(&psc->command, MPC52xx_PSC_RST_RX);
+ out_8(&psc->command, MPC52xx_PSC_RST_TX);
- out_be32(&psc->sicr,0); /* UART mode DCD ignored */
+ out_be32(&psc->sicr, 0); /* UART mode DCD ignored */
out_be16(&psc->mpc52xx_psc_clock_select, 0xdd00); /* /16 prescaler on */
out_be16(&fifo->tfalarm, 0x80);
port->read_status_mask |= MPC52xx_PSC_IMR_RXRDY | MPC52xx_PSC_IMR_TXRDY;
- out_be16(&psc->mpc52xx_psc_imr,port->read_status_mask);
+ out_be16(&psc->mpc52xx_psc_imr, port->read_status_mask);
- out_8(&psc->command,MPC52xx_PSC_TX_ENABLE);
- out_8(&psc->command,MPC52xx_PSC_RX_ENABLE);
+ out_8(&psc->command, MPC52xx_PSC_TX_ENABLE);
+ out_8(&psc->command, MPC52xx_PSC_RX_ENABLE);
return 0;
}
struct mpc52xx_psc __iomem *psc = PSC(port);
/* Shut down the port. Leave TX active if on a console port */
- out_8(&psc->command,MPC52xx_PSC_RST_RX);
+ out_8(&psc->command, MPC52xx_PSC_RST_RX);
if (!uart_console(port))
- out_8(&psc->command,MPC52xx_PSC_RST_TX);
+ out_8(&psc->command, MPC52xx_PSC_RST_TX);
port->read_status_mask = 0;
- out_be16(&psc->mpc52xx_psc_imr,port->read_status_mask);
+ out_be16(&psc->mpc52xx_psc_imr, port->read_status_mask);
/* Release interrupt */
free_irq(port->irq, port);
static void
mpc52xx_uart_set_termios(struct uart_port *port, struct ktermios *new,
- struct ktermios *old)
+ struct ktermios *old)
{
struct mpc52xx_psc __iomem *psc = PSC(port);
unsigned long flags;
mr1 = 0;
switch (new->c_cflag & CSIZE) {
- case CS5: mr1 |= MPC52xx_PSC_MODE_5_BITS;
- break;
- case CS6: mr1 |= MPC52xx_PSC_MODE_6_BITS;
- break;
- case CS7: mr1 |= MPC52xx_PSC_MODE_7_BITS;
- break;
- case CS8:
- default: mr1 |= MPC52xx_PSC_MODE_8_BITS;
+ case CS5: mr1 |= MPC52xx_PSC_MODE_5_BITS;
+ break;
+ case CS6: mr1 |= MPC52xx_PSC_MODE_6_BITS;
+ break;
+ case CS7: mr1 |= MPC52xx_PSC_MODE_7_BITS;
+ break;
+ case CS8:
+ default: mr1 |= MPC52xx_PSC_MODE_8_BITS;
}
if (new->c_cflag & PARENB) {
udelay(1);
if (!j)
- printk( KERN_ERR "mpc52xx_uart.c: "
+ printk(KERN_ERR "mpc52xx_uart.c: "
"Unable to flush RX & TX fifos in-time in set_termios."
- "Some chars may have been lost.\n" );
+ "Some chars may have been lost.\n");
/* Reset the TX & RX */
- out_8(&psc->command,MPC52xx_PSC_RST_RX);
- out_8(&psc->command,MPC52xx_PSC_RST_TX);
+ out_8(&psc->command, MPC52xx_PSC_RST_RX);
+ out_8(&psc->command, MPC52xx_PSC_RST_TX);
/* Send new mode settings */
- out_8(&psc->command,MPC52xx_PSC_SEL_MODE_REG_1);
- out_8(&psc->mode,mr1);
- out_8(&psc->mode,mr2);
- out_8(&psc->ctur,ctr >> 8);
- out_8(&psc->ctlr,ctr & 0xff);
+ out_8(&psc->command, MPC52xx_PSC_SEL_MODE_REG_1);
+ out_8(&psc->mode, mr1);
+ out_8(&psc->mode, mr2);
+ out_8(&psc->ctur, ctr >> 8);
+ out_8(&psc->ctlr, ctr & 0xff);
/* Reenable TX & RX */
- out_8(&psc->command,MPC52xx_PSC_TX_ENABLE);
- out_8(&psc->command,MPC52xx_PSC_RX_ENABLE);
+ out_8(&psc->command, MPC52xx_PSC_TX_ENABLE);
+ out_8(&psc->command, MPC52xx_PSC_RX_ENABLE);
/* We're all set, release the lock */
spin_unlock_irqrestore(&port->lock, flags);
static void
mpc52xx_uart_release_port(struct uart_port *port)
{
- if (port->flags & UPF_IOREMAP) { /* remapped by us ? */
+ /* remapped by us ? */
+ if (port->flags & UPF_IOREMAP) {
iounmap(port->membase);
port->membase = NULL;
}
if (port->flags & UPF_IOREMAP) /* Need to remap ? */
port->membase = ioremap(port->mapbase,
- sizeof(struct mpc52xx_psc));
+ sizeof(struct mpc52xx_psc));
if (!port->membase)
return -EINVAL;
static void
mpc52xx_uart_config_port(struct uart_port *port, int flags)
{
- if ( (flags & UART_CONFIG_TYPE) &&
- (mpc52xx_uart_request_port(port) == 0) )
- port->type = PORT_MPC52xx;
+ if ((flags & UART_CONFIG_TYPE)
+ && (mpc52xx_uart_request_port(port) == 0))
+ port->type = PORT_MPC52xx;
}
static int
mpc52xx_uart_verify_port(struct uart_port *port, struct serial_struct *ser)
{
- if ( ser->type != PORT_UNKNOWN && ser->type != PORT_MPC52xx )
+ if (ser->type != PORT_UNKNOWN && ser->type != PORT_MPC52xx)
return -EINVAL;
- if ( (ser->irq != port->irq) ||
- (ser->io_type != SERIAL_IO_MEM) ||
- (ser->baud_base != port->uartclk) ||
- (ser->iomem_base != (void*)port->mapbase) ||
- (ser->hub6 != 0 ) )
+ if ((ser->irq != port->irq) ||
+ (ser->io_type != SERIAL_IO_MEM) ||
+ (ser->baud_base != port->uartclk) ||
+ (ser->iomem_base != (void *)port->mapbase) ||
+ (ser->hub6 != 0))
return -EINVAL;
return 0;
unsigned short status;
/* While we can read, do so ! */
- while ( (status = in_be16(&PSC(port)->mpc52xx_psc_status)) &
- MPC52xx_PSC_SR_RXRDY) {
+ while ((status = in_be16(&PSC(port)->mpc52xx_psc_status)) &
+ MPC52xx_PSC_SR_RXRDY) {
/* Get the char */
ch = in_8(&PSC(port)->mpc52xx_psc_buffer_8);
flag = TTY_NORMAL;
port->icount.rx++;
- if ( status & (MPC52xx_PSC_SR_PE |
- MPC52xx_PSC_SR_FE |
- MPC52xx_PSC_SR_RB) ) {
+ if (status & (MPC52xx_PSC_SR_PE |
+ MPC52xx_PSC_SR_FE |
+ MPC52xx_PSC_SR_RB)) {
if (status & MPC52xx_PSC_SR_RB) {
flag = TTY_BREAK;
flag = TTY_FRAME;
/* Clear error condition */
- out_8(&PSC(port)->command,MPC52xx_PSC_RST_ERR_STAT);
+ out_8(&PSC(port)->command, MPC52xx_PSC_RST_ERR_STAT);
}
tty_insert_flip_char(tty, ch, flag);
/* Do we need to receive chars ? */
/* For this RX interrupts must be on and some chars waiting */
- if ( status & MPC52xx_PSC_IMR_RXRDY )
+ if (status & MPC52xx_PSC_IMR_RXRDY)
keepgoing |= mpc52xx_uart_int_rx_chars(port);
/* Do we need to send chars ? */
/* For this, TX must be ready and TX interrupt enabled */
- if ( status & MPC52xx_PSC_IMR_TXRDY )
+ if (status & MPC52xx_PSC_IMR_TXRDY)
keepgoing |= mpc52xx_uart_int_tx_chars(port);
/* Limit number of iteration */
- if ( !(--pass) )
+ if (!(--pass))
keepgoing = 0;
} while (keepgoing);
static void __init
mpc52xx_console_get_options(struct uart_port *port,
- int *baud, int *parity, int *bits, int *flow)
+ int *baud, int *parity, int *bits, int *flow)
{
struct mpc52xx_psc __iomem *psc = PSC(port);
unsigned char mr1;
pr_debug("mpc52xx_console_get_options(port=%p)\n", port);
/* Read the mode registers */
- out_8(&psc->command,MPC52xx_PSC_SEL_MODE_REG_1);
+ out_8(&psc->command, MPC52xx_PSC_SEL_MODE_REG_1);
mr1 = in_8(&psc->mode);
/* CT{U,L}R are write-only ! */
/* Parse them */
switch (mr1 & MPC52xx_PSC_MODE_BITS_MASK) {
- case MPC52xx_PSC_MODE_5_BITS: *bits = 5; break;
- case MPC52xx_PSC_MODE_6_BITS: *bits = 6; break;
- case MPC52xx_PSC_MODE_7_BITS: *bits = 7; break;
- case MPC52xx_PSC_MODE_8_BITS:
- default: *bits = 8;
+ case MPC52xx_PSC_MODE_5_BITS:
+ *bits = 5;
+ break;
+ case MPC52xx_PSC_MODE_6_BITS:
+ *bits = 6;
+ break;
+ case MPC52xx_PSC_MODE_7_BITS:
+ *bits = 7;
+ break;
+ case MPC52xx_PSC_MODE_8_BITS:
+ default:
+ *bits = 8;
}
if (mr1 & MPC52xx_PSC_MODE_PARNONE)
/* Wait the TX buffer to be empty */
j = 20000; /* Maximum wait */
while (!(in_be16(&psc->mpc52xx_psc_status) &
- MPC52xx_PSC_SR_TXEMP) && --j)
+ MPC52xx_PSC_SR_TXEMP) && --j)
udelay(1);
}
}
pr_debug("Console on ttyPSC%x is %s\n",
- co->index, mpc52xx_uart_nodes[co->index]->full_name);
+ co->index, mpc52xx_uart_nodes[co->index]->full_name);
/* Fetch register locations */
- if ((ret = of_address_to_resource(np, 0, &res)) != 0) {
+ ret = of_address_to_resource(np, 0, &res);
+ if (ret) {
pr_debug("Could not get resources for PSC%x\n", co->index);
return ret;
}
/* Search for bus-frequency property in this node or a parent */
- if ((ipb_freq = mpc52xx_find_ipb_freq(np)) == 0) {
+ ipb_freq = mpc52xx_find_ipb_freq(np);
+ if (ipb_freq == 0) {
pr_debug("Could not find IPB bus frequency!\n");
return -EINVAL;
}
return -EINVAL;
pr_debug("mpc52xx-psc uart at %p, mapped to %p, irq=%x, freq=%i\n",
- (void*)port->mapbase, port->membase, port->irq, port->uartclk);
+ (void *)port->mapbase, port->membase,
+ port->irq, port->uartclk);
/* Setup the port parameters accoding to options */
if (options)
mpc52xx_console_get_options(port, &baud, &parity, &bits, &flow);
pr_debug("Setting console parameters: %i %i%c1 flow=%c\n",
- baud, bits, parity, flow);
+ baud, bits, parity, flow);
return uart_set_options(port, co, baud, parity, bits, flow);
}
.device = uart_console_device,
.setup = mpc52xx_console_setup,
.flags = CON_PRINTBUFFER,
- .index = -1, /* Specified on the cmdline (e.g. console=ttyPSC0 ) */
+ .index = -1, /* Specified on the cmdline (e.g. console=ttyPSC0) */
.data = &mpc52xx_uart_driver,
};
/* ======================================================================== */
static struct uart_driver mpc52xx_uart_driver = {
- .owner = THIS_MODULE,
.driver_name = "mpc52xx_psc_uart",
.dev_name = "ttyPSC",
.major = SERIAL_PSC_MAJOR,
if (idx < 0 || idx >= MPC52xx_PSC_MAXNUM)
return -EINVAL;
- if (!mpc52xx_match_psc_function(idx,"uart"))
+ if (!mpc52xx_match_psc_function(idx, "uart"))
return -ENODEV;
/* Init the port structure */
port->fifosize = 512;
port->iotype = UPIO_MEM;
port->flags = UPF_BOOT_AUTOCONF |
- ( uart_console(port) ? 0 : UPF_IOREMAP );
+ (uart_console(port) ? 0 : UPF_IOREMAP);
port->line = idx;
port->ops = &mpc52xx_uart_ops;
port->dev = &dev->dev;
/* Search for IRQ and mapbase */
- for (i=0 ; i<dev->num_resources ; i++, res++) {
+ for (i = 0 ; i < dev->num_resources ; i++, res++) {
if (res->flags & IORESOURCE_MEM)
port->mapbase = res->start;
else if (res->flags & IORESOURCE_IRQ)
/* Add the port to the uart sub-system */
ret = uart_add_one_port(&mpc52xx_uart_driver, port);
if (!ret)
- platform_set_drvdata(dev, (void*)port);
+ platform_set_drvdata(dev, (void *)port);
return ret;
}
.resume = mpc52xx_uart_resume,
#endif
.driver = {
+ .owner = THIS_MODULE,
.name = "mpc52xx-psc",
},
};
if (idx >= MPC52xx_PSC_MAXNUM)
return -EINVAL;
pr_debug("Found %s assigned to ttyPSC%x\n",
- mpc52xx_uart_nodes[idx]->full_name, idx);
+ mpc52xx_uart_nodes[idx]->full_name, idx);
/* Search for bus-frequency property in this node or a parent */
- if ((ipb_freq = mpc52xx_find_ipb_freq(op->node)) == 0) {
+ ipb_freq = mpc52xx_find_ipb_freq(op->node);
+ if (ipb_freq == 0) {
dev_dbg(&op->dev, "Could not find IPB bus frequency!\n");
return -EINVAL;
}
port->fifosize = 512;
port->iotype = UPIO_MEM;
port->flags = UPF_BOOT_AUTOCONF |
- ( uart_console(port) ? 0 : UPF_IOREMAP );
+ (uart_console(port) ? 0 : UPF_IOREMAP);
port->line = idx;
port->ops = &mpc52xx_uart_ops;
port->dev = &op->dev;
/* Search for IRQ and mapbase */
- if ((ret = of_address_to_resource(op->node, 0, &res)) != 0)
+ ret = of_address_to_resource(op->node, 0, &res);
+ if (ret)
return ret;
port->mapbase = res.start;
port->irq = irq_of_parse_and_map(op->node, 0);
dev_dbg(&op->dev, "mpc52xx-psc uart at %p, irq=%x, freq=%i\n",
- (void*)port->mapbase, port->irq, port->uartclk);
+ (void *)port->mapbase, port->irq, port->uartclk);
- if ((port->irq==NO_IRQ) || !port->mapbase) {
+ if ((port->irq == NO_IRQ) || !port->mapbase) {
printk(KERN_ERR "Could not allocate resources for PSC\n");
return -EINVAL;
}
/* Add the port to the uart sub-system */
ret = uart_add_one_port(&mpc52xx_uart_driver, port);
if (!ret)
- dev_set_drvdata(&op->dev, (void*)port);
+ dev_set_drvdata(&op->dev, (void *)port);
return ret;
}
if (idx < 0)
return; /* No free slot; abort */
+ of_node_get(np);
/* If the slot is already occupied, then swap slots */
if (mpc52xx_uart_nodes[idx] && (free_idx != -1))
mpc52xx_uart_nodes[free_idx] = mpc52xx_uart_nodes[idx];
static void
mpc52xx_uart_of_enumerate(void)
{
- static int enum_done = 0;
+ static int enum_done;
struct device_node *np;
const unsigned int *devno;
int i;
/* Is a particular device number requested? */
devno = of_get_property(np, "port-number", NULL);
- mpc52xx_uart_of_assign(of_node_get(np), devno ? *devno : -1);
+ mpc52xx_uart_of_assign(np, devno ? *devno : -1);
}
enum_done = 1;
for (i = 0; i < MPC52xx_PSC_MAXNUM; i++) {
if (mpc52xx_uart_nodes[i])
pr_debug("%s assigned to ttyPSC%x\n",
- mpc52xx_uart_nodes[i]->full_name, i);
+ mpc52xx_uart_nodes[i]->full_name, i);
}
}
MODULE_DEVICE_TABLE(of, mpc52xx_uart_of_match);
static struct of_platform_driver mpc52xx_uart_of_driver = {
- .owner = THIS_MODULE,
- .name = "mpc52xx-psc-uart",
.match_table = mpc52xx_uart_of_match,
.probe = mpc52xx_uart_of_probe,
.remove = mpc52xx_uart_of_remove,
printk(KERN_INFO "Serial: MPC52xx PSC UART driver\n");
- if ((ret = uart_register_driver(&mpc52xx_uart_driver)) != 0) {
+ ret = uart_register_driver(&mpc52xx_uart_driver);
+ if (ret) {
printk(KERN_ERR "%s: uart_register_driver failed (%i)\n",
__FILE__, ret);
return ret;
projects / linux-2.6 / commitdiff