qla3xxx: Adding support for the Agere PHY (ET1011C)

This PHY support patch was written by Benjamin Li.
Signed-off-by: Benjamin Li <benjamin.li@qlogic.com>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

diff --git a/drivers/net/qla3xxx.c b/drivers/net/qla3xxx.c
index c2eb2c93803bdda740ef7ceda892adcfc89f7577..4061f7de48afd00a4a6f3845e2f948bdf8b44bf2 100755 (executable)
--- a/drivers/net/qla3xxx.c
+++ b/drivers/net/qla3xxx.c
@@ -71,6 +71,30 @@ static struct pci_device_id ql3xxx_pci_tbl[] __devinitdata = {
 
 MODULE_DEVICE_TABLE(pci, ql3xxx_pci_tbl);
 
+/*
+ *  These are the known PHY's which are used
+ */
+typedef enum {
+   PHY_TYPE_UNKNOWN   = 0,
+   PHY_VITESSE_VSC8211,
+   PHY_AGERE_ET1011C,
+   MAX_PHY_DEV_TYPES
+} PHY_DEVICE_et;
+
+typedef struct {
+       PHY_DEVICE_et phyDevice; 
+       u32             phyIdOUI;
+       u16             phyIdModel;
+       char            *name;
+} PHY_DEVICE_INFO_t;
+
+const PHY_DEVICE_INFO_t PHY_DEVICES[] =
+       {{PHY_TYPE_UNKNOWN,    0x000000, 0x0, "PHY_TYPE_UNKNOWN"},
+        {PHY_VITESSE_VSC8211, 0x0003f1, 0xb, "PHY_VITESSE_VSC8211"},
+        {PHY_AGERE_ET1011C,   0x00a0bc, 0x1, "PHY_AGERE_ET1011C"},
+};
+
+
 /*
  * Caller must take hw_lock.
  */
@@ -662,7 +686,7 @@ static u8 ql_mii_disable_scan_mode(struct ql3_adapter *qdev)
 }
 
 static int ql_mii_write_reg_ex(struct ql3_adapter *qdev,
-                              u16 regAddr, u16 value, u32 mac_index)
+                              u16 regAddr, u16 value, u32 phyAddr)
 {
        struct ql3xxx_port_registers __iomem *port_regs =
                        qdev->mem_map_registers;
@@ -680,7 +704,7 @@ static int ql_mii_write_reg_ex(struct ql3_adapter *qdev,
        }
 
        ql_write_page0_reg(qdev, &port_regs->macMIIMgmtAddrReg,
-                          PHYAddr[mac_index] | regAddr);
+                          phyAddr | regAddr);
 
        ql_write_page0_reg(qdev, &port_regs->macMIIMgmtDataReg, value);
 
@@ -701,7 +725,7 @@ static int ql_mii_write_reg_ex(struct ql3_adapter *qdev,
 }
 
 static int ql_mii_read_reg_ex(struct ql3_adapter *qdev, u16 regAddr,
-                             u16 * value, u32 mac_index)
+                             u16 * value, u32 phyAddr)
 {
        struct ql3xxx_port_registers __iomem *port_regs =
                        qdev->mem_map_registers;
@@ -720,7 +744,7 @@ static int ql_mii_read_reg_ex(struct ql3_adapter *qdev, u16 regAddr,
        }
 
        ql_write_page0_reg(qdev, &port_regs->macMIIMgmtAddrReg,
-                          PHYAddr[mac_index] | regAddr);
+                          phyAddr | regAddr);
 
        ql_write_page0_reg(qdev, &port_regs->macMIIMgmtControlReg,
                           (MAC_MII_CONTROL_RC << 16));
@@ -850,28 +874,31 @@ static void ql_petbi_start_neg(struct ql3_adapter *qdev)
 
 }
 
-static void ql_petbi_reset_ex(struct ql3_adapter *qdev, u32 mac_index)
+static void ql_petbi_reset_ex(struct ql3_adapter *qdev)
 {
        ql_mii_write_reg_ex(qdev, PETBI_CONTROL_REG, PETBI_CTRL_SOFT_RESET,
-                           mac_index);
+                           PHYAddr[qdev->mac_index]);
 }
 
-static void ql_petbi_start_neg_ex(struct ql3_adapter *qdev, u32 mac_index)
+static void ql_petbi_start_neg_ex(struct ql3_adapter *qdev)
 {
        u16 reg;
 
        /* Enable Auto-negotiation sense */
-       ql_mii_read_reg_ex(qdev, PETBI_TBI_CTRL, &reg, mac_index);
+       ql_mii_read_reg_ex(qdev, PETBI_TBI_CTRL, &reg, 
+                          PHYAddr[qdev->mac_index]);
        reg |= PETBI_TBI_AUTO_SENSE;
-       ql_mii_write_reg_ex(qdev, PETBI_TBI_CTRL, reg, mac_index);
+       ql_mii_write_reg_ex(qdev, PETBI_TBI_CTRL, reg, 
+                           PHYAddr[qdev->mac_index]);
 
        ql_mii_write_reg_ex(qdev, PETBI_NEG_ADVER,
-                           PETBI_NEG_PAUSE | PETBI_NEG_DUPLEX, mac_index);
+                           PETBI_NEG_PAUSE | PETBI_NEG_DUPLEX, 
+                           PHYAddr[qdev->mac_index]);
 
        ql_mii_write_reg_ex(qdev, PETBI_CONTROL_REG,
                            PETBI_CTRL_AUTO_NEG | PETBI_CTRL_RESTART_NEG |
                            PETBI_CTRL_FULL_DUPLEX | PETBI_CTRL_SPEED_1000,
-                           mac_index);
+                           PHYAddr[qdev->mac_index]);
 }
 
 static void ql_petbi_init(struct ql3_adapter *qdev)
@@ -880,10 +907,10 @@ static void ql_petbi_init(struct ql3_adapter *qdev)
        ql_petbi_start_neg(qdev);
 }
 
-static void ql_petbi_init_ex(struct ql3_adapter *qdev, u32 mac_index)
+static void ql_petbi_init_ex(struct ql3_adapter *qdev)
 {
-       ql_petbi_reset_ex(qdev, mac_index);
-       ql_petbi_start_neg_ex(qdev, mac_index);
+       ql_petbi_reset_ex(qdev);
+       ql_petbi_start_neg_ex(qdev);
 }
 
 static int ql_is_petbi_neg_pause(struct ql3_adapter *qdev)
@@ -896,33 +923,128 @@ static int ql_is_petbi_neg_pause(struct ql3_adapter *qdev)
        return (reg & PETBI_NEG_PAUSE_MASK) == PETBI_NEG_PAUSE;
 }
 
+static void phyAgereSpecificInit(struct ql3_adapter *qdev, u32 miiAddr)
+{
+       printk(KERN_INFO "%s: enabling Agere specific PHY\n", qdev->ndev->name);
+       /* power down device bit 11 = 1 */
+       ql_mii_write_reg_ex(qdev, 0x00, 0x1940, miiAddr);
+       /* enable diagnostic mode bit 2 = 1 */
+       ql_mii_write_reg_ex(qdev, 0x12, 0x840e, miiAddr);
+       /* 1000MB amplitude adjust (see Agere errata) */
+       ql_mii_write_reg_ex(qdev, 0x10, 0x8805, miiAddr);
+       /* 1000MB amplitude adjust (see Agere errata) */
+       ql_mii_write_reg_ex(qdev, 0x11, 0xf03e, miiAddr);
+       /* 100MB amplitude adjust (see Agere errata) */
+       ql_mii_write_reg_ex(qdev, 0x10, 0x8806, miiAddr);
+       /* 100MB amplitude adjust (see Agere errata) */
+       ql_mii_write_reg_ex(qdev, 0x11, 0x003e, miiAddr);
+       /* 10MB amplitude adjust (see Agere errata) */
+       ql_mii_write_reg_ex(qdev, 0x10, 0x8807, miiAddr);
+       /* 10MB amplitude adjust (see Agere errata) */
+       ql_mii_write_reg_ex(qdev, 0x11, 0x1f00, miiAddr);
+       /* point to hidden reg 0x2806 */
+       ql_mii_write_reg_ex(qdev, 0x10, 0x2806, miiAddr);
+       /* Write new PHYAD w/bit 5 set */
+       ql_mii_write_reg_ex(qdev, 0x11, 0x0020 | (PHYAddr[qdev->mac_index] >> 8), miiAddr);
+       /* 
+        * Disable diagnostic mode bit 2 = 0
+        * Power up device bit 11 = 0
+        * Link up (on) and activity (blink)
+        */
+       ql_mii_write_reg(qdev, 0x12, 0x840a);
+       ql_mii_write_reg(qdev, 0x00, 0x1140);
+       ql_mii_write_reg(qdev, 0x1c, 0xfaf0);
+}
+
+static PHY_DEVICE_et getPhyType (struct ql3_adapter *qdev, 
+                                u16 phyIdReg0, u16 phyIdReg1)
+{
+       PHY_DEVICE_et result = PHY_TYPE_UNKNOWN;
+       u32   oui;     
+       u16   model;
+       int i;   
+
+       if (phyIdReg0 == 0xffff) {
+               return result;
+       }
+   
+       if (phyIdReg1 == 0xffff) {
+               return result;
+       }
+
+       /* oui is split between two registers */
+       oui = (phyIdReg0 << 6) | ((phyIdReg1 & PHY_OUI_1_MASK) >> 10);
+
+       model = (phyIdReg1 & PHY_MODEL_MASK) >> 4;
+
+       /* Scan table for this PHY */
+       for(i = 0; i < MAX_PHY_DEV_TYPES; i++) {
+               if ((oui == PHY_DEVICES[i].phyIdOUI) && (model == PHY_DEVICES[i].phyIdModel))
+               {
+                       result = PHY_DEVICES[i].phyDevice;
+
+                       printk(KERN_INFO "%s: Phy: %s\n",
+                               qdev->ndev->name, PHY_DEVICES[i].name);
+                       
+                       break;
+               }
+       }
+
+       return result;
+}
+
 static int ql_phy_get_speed(struct ql3_adapter *qdev)
 {
        u16 reg;
 
+       switch(qdev->phyType) {
+       case PHY_AGERE_ET1011C:
+       {
+               if (ql_mii_read_reg(qdev, 0x1A, &reg) < 0)
+                       return 0;
+
+               reg = (reg >> 8) & 3;
+               break;
+       }
+       default:
        if (ql_mii_read_reg(qdev, AUX_CONTROL_STATUS, &reg) < 0)
                return 0;
 
        reg = (((reg & 0x18) >> 3) & 3);
+       }
 
-       if (reg == 2)
+       switch(reg) {
+               case 2:
                return SPEED_1000;
-       else if (reg == 1)
+               case 1:
                return SPEED_100;
-       else if (reg == 0)
+               case 0:
                return SPEED_10;
-       else
+               default:
                return -1;
+       }
 }
 
 static int ql_is_full_dup(struct ql3_adapter *qdev)
 {
        u16 reg;
 
-       if (ql_mii_read_reg(qdev, AUX_CONTROL_STATUS, &reg) < 0)
-               return 0;
-
-       return (reg & PHY_AUX_DUPLEX_STAT) != 0;
+       switch(qdev->phyType) {
+       case PHY_AGERE_ET1011C:
+       {
+               if (ql_mii_read_reg(qdev, 0x1A, &reg))
+                       return 0;
+                       
+               return ((reg & 0x0080) && (reg & 0x1000)) != 0;
+       }
+       case PHY_VITESSE_VSC8211:
+       default:
+       {
+               if (ql_mii_read_reg(qdev, AUX_CONTROL_STATUS, &reg) < 0)
+                       return 0;
+               return (reg & PHY_AUX_DUPLEX_STAT) != 0;
+       }
+       }
 }
 
 static int ql_is_phy_neg_pause(struct ql3_adapter *qdev)
@@ -935,6 +1057,73 @@ static int ql_is_phy_neg_pause(struct ql3_adapter *qdev)
        return (reg & PHY_NEG_PAUSE) != 0;
 }
 
+static int PHY_Setup(struct ql3_adapter *qdev)
+{
+       u16   reg1;
+       u16   reg2;
+       bool  agereAddrChangeNeeded = false;
+       u32 miiAddr = 0;
+       int err;
+
+       /*  Determine the PHY we are using by reading the ID's */
+       err = ql_mii_read_reg(qdev, PHY_ID_0_REG, &reg1);
+       if(err != 0) {
+               printk(KERN_ERR "%s: Could not read from reg PHY_ID_0_REG\n",
+                      qdev->ndev->name);
+                return err;
+       }
+
+       err = ql_mii_read_reg(qdev, PHY_ID_1_REG, &reg2);
+       if(err != 0) {
+               printk(KERN_ERR "%s: Could not read from reg PHY_ID_0_REG\n",
+                      qdev->ndev->name);
+                return err;
+       }
+
+       /*  Check if we have a Agere PHY */
+       if ((reg1 == 0xffff) || (reg2 == 0xffff)) {
+
+               /* Determine which MII address we should be using 
+                  determined by the index of the card */
+               if (qdev->mac_index == 0) {
+                       miiAddr = MII_AGERE_ADDR_1;
+               } else {
+                       miiAddr = MII_AGERE_ADDR_2;
+               }
+      
+               err =ql_mii_read_reg_ex(qdev, PHY_ID_0_REG, &reg1, miiAddr);
+               if(err != 0) {
+                       printk(KERN_ERR "%s: Could not read from reg PHY_ID_0_REG after Agere detected\n",
+                              qdev->ndev->name);
+                       return err; 
+               }
+
+               err = ql_mii_read_reg_ex(qdev, PHY_ID_1_REG, &reg2, miiAddr);
+               if(err != 0) {
+                       printk(KERN_ERR "%s: Could not read from reg PHY_ID_0_REG after Agere detected\n",
+                              qdev->ndev->name);
+                       return err;
+               }
+   
+               /*  We need to remember to initialize the Agere PHY */
+               agereAddrChangeNeeded = true; 
+       }
+
+       /*  Determine the particular PHY we have on board to apply
+           PHY specific initializations */
+       qdev->phyType = getPhyType(qdev, reg1, reg2);
+
+       if ((qdev->phyType == PHY_AGERE_ET1011C) && agereAddrChangeNeeded) {
+               /* need this here so address gets changed */
+               phyAgereSpecificInit(qdev, miiAddr);  
+       } else if (qdev->phyType == PHY_TYPE_UNKNOWN) {
+               printk(KERN_ERR "%s: PHY is unknown\n", qdev->ndev->name);
+               return -EIO;
+       }
+
+       return 0;
+}
+
 /*
  * Caller holds hw_lock.
  */
@@ -1205,15 +1394,14 @@ static int ql_link_down_detect_clear(struct ql3_adapter *qdev)
 /*
  * Caller holds hw_lock.
  */
-static int ql_this_adapter_controls_port(struct ql3_adapter *qdev,
-                                        u32 mac_index)
+static int ql_this_adapter_controls_port(struct ql3_adapter *qdev)
 {
        struct ql3xxx_port_registers __iomem *port_regs =
                        qdev->mem_map_registers;
        u32 bitToCheck = 0;
        u32 temp;
 
-       switch (mac_index) {
+       switch (qdev->mac_index) {
        case 0:
                bitToCheck = PORT_STATUS_F1_ENABLED;
                break;
@@ -1238,27 +1426,96 @@ static int ql_this_adapter_controls_port(struct ql3_adapter *qdev,
        }
 }
 
-static void ql_phy_reset_ex(struct ql3_adapter *qdev, u32 mac_index)
+static void ql_phy_reset_ex(struct ql3_adapter *qdev)
 {
-       ql_mii_write_reg_ex(qdev, CONTROL_REG, PHY_CTRL_SOFT_RESET, mac_index);
+       ql_mii_write_reg_ex(qdev, CONTROL_REG, PHY_CTRL_SOFT_RESET, 
+                           PHYAddr[qdev->mac_index]);
 }
 
-static void ql_phy_start_neg_ex(struct ql3_adapter *qdev, u32 mac_index)
+static void ql_phy_start_neg_ex(struct ql3_adapter *qdev)
 {
        u16 reg;
+       u16 portConfiguration;
 
-       ql_mii_write_reg_ex(qdev, PHY_NEG_ADVER,
-                           PHY_NEG_PAUSE | PHY_NEG_ADV_SPEED | 1, mac_index);
+       if(qdev->phyType == PHY_AGERE_ET1011C) {
+               /* turn off external loopback */
+               ql_mii_write_reg(qdev, 0x13, 0x0000); 
+       }
+
+       if(qdev->mac_index == 0)
+               portConfiguration = qdev->nvram_data.macCfg_port0.portConfiguration;
+       else
+               portConfiguration = qdev->nvram_data.macCfg_port1.portConfiguration;
+
+       /*  Some HBA's in the field are set to 0 and they need to
+           be reinterpreted with a default value */
+       if(portConfiguration == 0)
+               portConfiguration = PORT_CONFIG_DEFAULT;
+
+       /* Set the 1000 advertisements */
+       ql_mii_read_reg_ex(qdev, PHY_GIG_CONTROL, &reg, 
+                          PHYAddr[qdev->mac_index]);
+       reg &= ~PHY_GIG_ALL_PARAMS;
+
+       if(portConfiguration & 
+          PORT_CONFIG_FULL_DUPLEX_ENABLED &
+          PORT_CONFIG_1000MB_SPEED) {
+               reg |= PHY_GIG_ADV_1000F;
+       }
+        
+       if(portConfiguration & 
+          PORT_CONFIG_HALF_DUPLEX_ENABLED &
+          PORT_CONFIG_1000MB_SPEED) {
+               reg |= PHY_GIG_ADV_1000H;
+       }
+
+       ql_mii_write_reg_ex(qdev, PHY_GIG_CONTROL, reg, 
+                           PHYAddr[qdev->mac_index]);
+
+       /* Set the 10/100 & pause negotiation advertisements */
+       ql_mii_read_reg_ex(qdev, PHY_NEG_ADVER, &reg,
+                          PHYAddr[qdev->mac_index]);
+       reg &= ~PHY_NEG_ALL_PARAMS;
+
+       if(portConfiguration & PORT_CONFIG_SYM_PAUSE_ENABLED)
+               reg |= PHY_NEG_ASY_PAUSE | PHY_NEG_SYM_PAUSE;
+
+       if(portConfiguration & PORT_CONFIG_FULL_DUPLEX_ENABLED) {
+               if(portConfiguration & PORT_CONFIG_100MB_SPEED)
+                       reg |= PHY_NEG_ADV_100F;
+               
+               if(portConfiguration & PORT_CONFIG_10MB_SPEED)
+                       reg |= PHY_NEG_ADV_10F;
+       }
 
-       ql_mii_read_reg_ex(qdev, CONTROL_REG, &reg, mac_index);
-       ql_mii_write_reg_ex(qdev, CONTROL_REG, reg | PHY_CTRL_RESTART_NEG,
-                           mac_index);
+       if(portConfiguration & PORT_CONFIG_HALF_DUPLEX_ENABLED) {
+               if(portConfiguration & PORT_CONFIG_100MB_SPEED)
+                       reg |= PHY_NEG_ADV_100H;
+               
+               if(portConfiguration & PORT_CONFIG_10MB_SPEED)
+                       reg |= PHY_NEG_ADV_10H;
+       }
+
+       if(portConfiguration &
+          PORT_CONFIG_1000MB_SPEED) {
+               reg |= 1;       
+       }
+
+       ql_mii_write_reg_ex(qdev, PHY_NEG_ADVER, reg, 
+                           PHYAddr[qdev->mac_index]);
+
+       ql_mii_read_reg_ex(qdev, CONTROL_REG, &reg, PHYAddr[qdev->mac_index]);
+       
+       ql_mii_write_reg_ex(qdev, CONTROL_REG, 
+                           reg | PHY_CTRL_RESTART_NEG | PHY_CTRL_AUTO_NEG,
+                           PHYAddr[qdev->mac_index]);
 }
 
-static void ql_phy_init_ex(struct ql3_adapter *qdev, u32 mac_index)
+static void ql_phy_init_ex(struct ql3_adapter *qdev)
 {
-       ql_phy_reset_ex(qdev, mac_index);
-       ql_phy_start_neg_ex(qdev, mac_index);
+       ql_phy_reset_ex(qdev);
+       PHY_Setup(qdev);
+       ql_phy_start_neg_ex(qdev);
 }
 
 /*
@@ -1295,14 +1552,17 @@ static int ql_port_start(struct ql3_adapter *qdev)
 {
        if(ql_sem_spinlock(qdev, QL_PHY_GIO_SEM_MASK,
                (QL_RESOURCE_BITS_BASE_CODE | (qdev->mac_index) *
-                        2) << 7))
+                        2) << 7)) {
+               printk(KERN_ERR "%s: Could not get hw lock for GIO\n",
+                      qdev->ndev->name);
                return -1;
+       }
 
        if (ql_is_fiber(qdev)) {
                ql_petbi_init(qdev);
        } else {
                /* Copper port */
-               ql_phy_init_ex(qdev, qdev->mac_index);
+               ql_phy_init_ex(qdev);
        }
 
        ql_sem_unlock(qdev, QL_PHY_GIO_SEM_MASK);
@@ -1453,7 +1713,7 @@ static void ql_link_state_machine(struct ql3_adapter *qdev)
  */
 static void ql_get_phy_owner(struct ql3_adapter *qdev)
 {
-       if (ql_this_adapter_controls_port(qdev, qdev->mac_index))
+       if (ql_this_adapter_controls_port(qdev))
                set_bit(QL_LINK_MASTER,&qdev->flags);
        else
                clear_bit(QL_LINK_MASTER,&qdev->flags);
@@ -1467,11 +1727,11 @@ static void ql_init_scan_mode(struct ql3_adapter *qdev)
        ql_mii_enable_scan_mode(qdev);
 
        if (test_bit(QL_LINK_OPTICAL,&qdev->flags)) {
-               if (ql_this_adapter_controls_port(qdev, qdev->mac_index))
-                       ql_petbi_init_ex(qdev, qdev->mac_index);
+               if (ql_this_adapter_controls_port(qdev))
+                       ql_petbi_init_ex(qdev);
        } else {
-               if (ql_this_adapter_controls_port(qdev, qdev->mac_index))
-                       ql_phy_init_ex(qdev, qdev->mac_index);
+               if (ql_this_adapter_controls_port(qdev))
+                       ql_phy_init_ex(qdev);
        }
 }
 
@@ -3092,6 +3352,7 @@ static int ql_adapter_initialize(struct ql3_adapter *qdev)
                goto out;
        }
 
+       PHY_Setup(qdev);
        ql_init_scan_mode(qdev);
        ql_get_phy_owner(qdev);
 

diff --git a/drivers/net/qla3xxx.h b/drivers/net/qla3xxx.h
index 0203f88f0544413eb52c6a30c5c70797435aff92..4a832c46c274813541731937374389caad3efbe9 100755 (executable)
--- a/drivers/net/qla3xxx.h
+++ b/drivers/net/qla3xxx.h
@@ -293,6 +293,16 @@ struct net_rsp_iocb {
 
 #define MII_SCAN_REGISTER 0x00000001
 
+#define PHY_ID_0_REG    2
+#define PHY_ID_1_REG    3
+
+#define PHY_OUI_1_MASK       0xfc00
+#define PHY_MODEL_MASK       0x03f0
+
+/*  Address for the Agere Phy */
+#define MII_AGERE_ADDR_1  0x00001000
+#define MII_AGERE_ADDR_2  0x00001100
+
 /* 32-bit ispControlStatus */
 enum {
        ISP_CONTROL_NP_MASK = 0x0003,
@@ -789,6 +799,7 @@ enum {
        PHY_CTRL_LOOPBACK = 0x4000,
 
        PETBI_CONTROL_REG = 0x00,
+       PETBI_CTRL_ALL_PARAMS = 0x7140,
        PETBI_CTRL_SOFT_RESET = 0x8000,
        PETBI_CTRL_AUTO_NEG = 0x1000,
        PETBI_CTRL_RESTART_NEG = 0x0200,
@@ -811,6 +822,23 @@ enum {
        PETBI_EXPANSION_REG = 0x06,
        PETBI_EXP_PAGE_RX = 0x0002,
 
+       PHY_GIG_CONTROL = 9,
+       PHY_GIG_ENABLE_MAN = 0x1000,  /* Enable Master/Slave Manual Config*/
+       PHY_GIG_SET_MASTER = 0x0800,  /* Set Master (slave if clear)*/
+       PHY_GIG_ALL_PARAMS = 0x0300,
+       PHY_GIG_ADV_1000F = 0x0200,
+       PHY_GIG_ADV_1000H = 0x0100,
+
+       PHY_NEG_ADVER = 4,
+       PHY_NEG_ALL_PARAMS = 0x0fe0,
+       PHY_NEG_ASY_PAUSE =  0x0800,
+       PHY_NEG_SYM_PAUSE =  0x0400,
+       PHY_NEG_ADV_SPEED =  0x01e0,
+       PHY_NEG_ADV_100F =   0x0100,
+       PHY_NEG_ADV_100H =   0x0080,
+       PHY_NEG_ADV_10F =    0x0040,
+       PHY_NEG_ADV_10H =    0x0020,
+
        PETBI_TBI_CTRL = 0x11,
        PETBI_TBI_RESET = 0x8000,
        PETBI_TBI_AUTO_SENSE = 0x0100,
@@ -826,8 +854,7 @@ enum {
        PHY_AUX_RESET_STICK = 0x0002,
        PHY_NEG_PAUSE = 0x0400,
        PHY_CTRL_SOFT_RESET = 0x8000,
-       PHY_NEG_ADVER = 4,
-       PHY_NEG_ADV_SPEED = 0x01e0,
+       PHY_CTRL_AUTO_NEG = 0x1000,
        PHY_CTRL_RESTART_NEG = 0x0200,
 };
 enum {
@@ -892,6 +919,7 @@ enum {EEPROM_SIZE = FM93C86A_SIZE_16,
        u16 pauseThreshold_mac;
        u16 resumeThreshold_mac;
        u16 portConfiguration;
+#define PORT_CONFIG_DEFAULT                 0xf700
 #define PORT_CONFIG_AUTO_NEG_ENABLED        0x8000
 #define PORT_CONFIG_SYM_PAUSE_ENABLED       0x4000
 #define PORT_CONFIG_FULL_DUPLEX_ENABLED     0x2000
@@ -1259,6 +1287,7 @@ struct ql3_adapter {
        struct delayed_work tx_timeout_work;
        u32 max_frame_size;
        u32 device_id;
+       u16 phyType;
 };
 
 #endif                         /* _QLA3XXX_H_ */