be called ibmveth.
config IBM_EMAC
- bool "IBM PPC4xx EMAC driver support"
+ tristate "PowerPC 4xx on-chip Ethernet support"
depends on 4xx
- select CRC32
- ---help---
- This driver supports the IBM PPC4xx EMAC family of on-chip
- Ethernet controllers.
-
-config IBM_EMAC_ERRMSG
- bool "Verbose error messages"
- depends on IBM_EMAC && BROKEN
+ help
+ This driver supports the PowerPC 4xx EMAC family of on-chip
+ Ethernet controllers.
config IBM_EMAC_RXB
int "Number of receive buffers"
depends on IBM_EMAC
- default "128" if IBM_EMAC4
- default "64"
+ default "128"
config IBM_EMAC_TXB
int "Number of transmit buffers"
depends on IBM_EMAC
- default "128" if IBM_EMAC4
- default "8"
+ default "64"
+
+config IBM_EMAC_POLL_WEIGHT
+ int "MAL NAPI polling weight"
+ depends on IBM_EMAC
+ default "32"
-config IBM_EMAC_FGAP
- int "Frame gap"
+config IBM_EMAC_RX_COPY_THRESHOLD
+ int "RX skb copy threshold (bytes)"
depends on IBM_EMAC
- default "8"
+ default "256"
-config IBM_EMAC_SKBRES
- int "Skb reserve amount"
+config IBM_EMAC_RX_SKB_HEADROOM
+ int "Additional RX skb headroom (bytes)"
depends on IBM_EMAC
default "0"
+ help
+ Additional receive skb headroom. Note, that driver
+ will always reserve at least 2 bytes to make IP header
+ aligned, so usualy there is no need to add any additional
+ headroom.
+
+ If unsure, set to 0.
+
+config IBM_EMAC_PHY_RX_CLK_FIX
+ bool "PHY Rx clock workaround"
+ depends on IBM_EMAC && (405EP || 440GX || 440EP)
+ help
+ Enable this if EMAC attached to a PHY which doesn't generate
+ RX clock if there is no link, if this is the case, you will
+ see "TX disable timeout" or "RX disable timeout" in the system
+ log.
+
+ If unsure, say N.
+
+config IBM_EMAC_DEBUG
+ bool "Debugging"
+ depends on IBM_EMAC
+ default n
+
+config IBM_EMAC_ZMII
+ bool
+ depends on IBM_EMAC && (NP405H || NP405L || 44x)
+ default y
+
+config IBM_EMAC_RGMII
+ bool
+ depends on IBM_EMAC && 440GX
+ default y
+
+config IBM_EMAC_TAH
+ bool
+ depends on IBM_EMAC && 440GX
+ default y
config NET_PCI
bool "EISA, VLB, PCI and on board controllers"
#
-# Makefile for the IBM PPC4xx EMAC controllers
+# Makefile for the PowerPC 4xx on-chip ethernet driver
#
obj-$(CONFIG_IBM_EMAC) += ibm_emac.o
-ibm_emac-objs := ibm_emac_mal.o ibm_emac_core.o ibm_emac_phy.o
-
-# Only need this if you want to see additional debug messages
-ifeq ($(CONFIG_IBM_EMAC_ERRMSG), y)
-ibm_emac-objs += ibm_emac_debug.o
-endif
+ibm_emac-objs := ibm_emac_mal.o ibm_emac_core.o ibm_emac_phy.o
+ibm_emac-$(CONFIG_IBM_EMAC_ZMII) += ibm_emac_zmii.o
+ibm_emac-$(CONFIG_IBM_EMAC_RGMII) += ibm_emac_rgmii.o
+ibm_emac-$(CONFIG_IBM_EMAC_TAH) += ibm_emac_tah.o
+ibm_emac-$(CONFIG_IBM_EMAC_DEBUG) += ibm_emac_debug.o
/*
- * ibm_emac.h
+ * drivers/net/ibm_emac/ibm_emac.h
*
+ * Register definitions for PowerPC 4xx on-chip ethernet contoller
*
- * Armin Kuster akuster@mvista.com
- * June, 2002
+ * Copyright (c) 2004, 2005 Zultys Technologies.
+ * Eugene Surovegin <eugene.surovegin@zultys.com> or <ebs@ebshome.net>
*
- * Copyright 2002 MontaVista Softare Inc.
+ * Based on original work by
+ * Matt Porter <mporter@kernel.crashing.org>
+ * Armin Kuster <akuster@mvista.com>
+ * Copyright 2002-2004 MontaVista Software Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
+ *
*/
+#ifndef __IBM_EMAC_H_
+#define __IBM_EMAC_H_
+
+#include <linux/config.h>
+#include <linux/types.h>
+
+/* This is a simple check to prevent use of this driver on non-tested SoCs */
+#if !defined(CONFIG_405GP) && !defined(CONFIG_405GPR) && !defined(CONFIG_405EP) && \
+ !defined(CONFIG_440GP) && !defined(CONFIG_440GX) && !defined(CONFIG_440SP) && \
+ !defined(CONFIG_440EP) && !defined(CONFIG_NP405H)
+#error "Unknown SoC. Please, check chip user manual and make sure EMAC defines are OK"
+#endif
+
+/* EMAC registers Write Access rules */
+struct emac_regs {
+ u32 mr0; /* special */
+ u32 mr1; /* Reset */
+ u32 tmr0; /* special */
+ u32 tmr1; /* special */
+ u32 rmr; /* Reset */
+ u32 isr; /* Always */
+ u32 iser; /* Reset */
+ u32 iahr; /* Reset, R, T */
+ u32 ialr; /* Reset, R, T */
+ u32 vtpid; /* Reset, R, T */
+ u32 vtci; /* Reset, R, T */
+ u32 ptr; /* Reset, T */
+ u32 iaht1; /* Reset, R */
+ u32 iaht2; /* Reset, R */
+ u32 iaht3; /* Reset, R */
+ u32 iaht4; /* Reset, R */
+ u32 gaht1; /* Reset, R */
+ u32 gaht2; /* Reset, R */
+ u32 gaht3; /* Reset, R */
+ u32 gaht4; /* Reset, R */
+ u32 lsah;
+ u32 lsal;
+ u32 ipgvr; /* Reset, T */
+ u32 stacr; /* special */
+ u32 trtr; /* special */
+ u32 rwmr; /* Reset */
+ u32 octx;
+ u32 ocrx;
+ u32 ipcr;
+};
+
+#if !defined(CONFIG_IBM_EMAC4)
+#define EMAC_ETHTOOL_REGS_VER 0
+#define EMAC_ETHTOOL_REGS_SIZE (sizeof(struct emac_regs) - sizeof(u32))
+#else
+#define EMAC_ETHTOOL_REGS_VER 1
+#define EMAC_ETHTOOL_REGS_SIZE sizeof(struct emac_regs)
+#endif
-#ifndef _IBM_EMAC_H_
-#define _IBM_EMAC_H_
-/* General defines needed for the driver */
+/* EMACx_MR0 */
+#define EMAC_MR0_RXI 0x80000000
+#define EMAC_MR0_TXI 0x40000000
+#define EMAC_MR0_SRST 0x20000000
+#define EMAC_MR0_TXE 0x10000000
+#define EMAC_MR0_RXE 0x08000000
+#define EMAC_MR0_WKE 0x04000000
-/* Emac */
-typedef struct emac_regs {
- u32 em0mr0;
- u32 em0mr1;
- u32 em0tmr0;
- u32 em0tmr1;
- u32 em0rmr;
- u32 em0isr;
- u32 em0iser;
- u32 em0iahr;
- u32 em0ialr;
- u32 em0vtpid;
- u32 em0vtci;
- u32 em0ptr;
- u32 em0iaht1;
- u32 em0iaht2;
- u32 em0iaht3;
- u32 em0iaht4;
- u32 em0gaht1;
- u32 em0gaht2;
- u32 em0gaht3;
- u32 em0gaht4;
- u32 em0lsah;
- u32 em0lsal;
- u32 em0ipgvr;
- u32 em0stacr;
- u32 em0trtr;
- u32 em0rwmr;
-} emac_t;
+/* EMACx_MR1 */
+#define EMAC_MR1_FDE 0x80000000
+#define EMAC_MR1_ILE 0x40000000
+#define EMAC_MR1_VLE 0x20000000
+#define EMAC_MR1_EIFC 0x10000000
+#define EMAC_MR1_APP 0x08000000
+#define EMAC_MR1_IST 0x01000000
-/* MODE REG 0 */
-#define EMAC_M0_RXI 0x80000000
-#define EMAC_M0_TXI 0x40000000
-#define EMAC_M0_SRST 0x20000000
-#define EMAC_M0_TXE 0x10000000
-#define EMAC_M0_RXE 0x08000000
-#define EMAC_M0_WKE 0x04000000
+#define EMAC_MR1_MF_MASK 0x00c00000
+#define EMAC_MR1_MF_10 0x00000000
+#define EMAC_MR1_MF_100 0x00400000
+#if !defined(CONFIG_IBM_EMAC4)
+#define EMAC_MR1_MF_1000 0x00000000
+#define EMAC_MR1_MF_1000GPCS 0x00000000
+#define EMAC_MR1_MF_IPPA(id) 0x00000000
+#else
+#define EMAC_MR1_MF_1000 0x00800000
+#define EMAC_MR1_MF_1000GPCS 0x00c00000
+#define EMAC_MR1_MF_IPPA(id) (((id) & 0x1f) << 6)
+#endif
-/* MODE Reg 1 */
-#define EMAC_M1_FDE 0x80000000
-#define EMAC_M1_ILE 0x40000000
-#define EMAC_M1_VLE 0x20000000
-#define EMAC_M1_EIFC 0x10000000
-#define EMAC_M1_APP 0x08000000
-#define EMAC_M1_AEMI 0x02000000
-#define EMAC_M1_IST 0x01000000
-#define EMAC_M1_MF_1000GPCS 0x00c00000 /* Internal GPCS */
-#define EMAC_M1_MF_1000MBPS 0x00800000 /* External GPCS */
-#define EMAC_M1_MF_100MBPS 0x00400000
-#define EMAC_M1_RFS_16K 0x00280000 /* 000 for 512 byte */
-#define EMAC_M1_TR 0x00008000
-#ifdef CONFIG_IBM_EMAC4
-#define EMAC_M1_RFS_8K 0x00200000
-#define EMAC_M1_RFS_4K 0x00180000
-#define EMAC_M1_RFS_2K 0x00100000
-#define EMAC_M1_RFS_1K 0x00080000
-#define EMAC_M1_TX_FIFO_16K 0x00050000 /* 0's for 512 byte */
-#define EMAC_M1_TX_FIFO_8K 0x00040000
-#define EMAC_M1_TX_FIFO_4K 0x00030000
-#define EMAC_M1_TX_FIFO_2K 0x00020000
-#define EMAC_M1_TX_FIFO_1K 0x00010000
-#define EMAC_M1_TX_TR 0x00008000
-#define EMAC_M1_TX_MWSW 0x00001000 /* 0 wait for status */
-#define EMAC_M1_JUMBO_ENABLE 0x00000800 /* Upt to 9Kr status */
-#define EMAC_M1_OPB_CLK_66 0x00000008 /* 66Mhz */
-#define EMAC_M1_OPB_CLK_83 0x00000010 /* 83Mhz */
-#define EMAC_M1_OPB_CLK_100 0x00000018 /* 100Mhz */
-#define EMAC_M1_OPB_CLK_100P 0x00000020 /* 100Mhz+ */
-#else /* CONFIG_IBM_EMAC4 */
-#define EMAC_M1_RFS_4K 0x00300000 /* ~4k for 512 byte */
-#define EMAC_M1_RFS_2K 0x00200000
-#define EMAC_M1_RFS_1K 0x00100000
-#define EMAC_M1_TX_FIFO_2K 0x00080000 /* 0's for 512 byte */
-#define EMAC_M1_TX_FIFO_1K 0x00040000
-#define EMAC_M1_TR0_DEPEND 0x00010000 /* 0'x for single packet */
-#define EMAC_M1_TR1_DEPEND 0x00004000
-#define EMAC_M1_TR1_MULTI 0x00002000
-#define EMAC_M1_JUMBO_ENABLE 0x00001000
-#endif /* CONFIG_IBM_EMAC4 */
-#define EMAC_M1_BASE (EMAC_M1_TX_FIFO_2K | \
- EMAC_M1_APP | \
- EMAC_M1_TR | EMAC_M1_VLE)
+#define EMAC_TX_FIFO_SIZE 2048
-/* Transmit Mode Register 0 */
-#define EMAC_TMR0_GNP0 0x80000000
-#define EMAC_TMR0_GNP1 0x40000000
-#define EMAC_TMR0_GNPD 0x20000000
-#define EMAC_TMR0_FC 0x10000000
+#if !defined(CONFIG_IBM_EMAC4)
+#define EMAC_MR1_RFS_4K 0x00300000
+#define EMAC_MR1_RFS_16K 0x00000000
+#define EMAC_RX_FIFO_SIZE(gige) 4096
+#define EMAC_MR1_TFS_2K 0x00080000
+#define EMAC_MR1_TR0_MULT 0x00008000
+#define EMAC_MR1_JPSM 0x00000000
+#define EMAC_MR1_BASE(opb) (EMAC_MR1_TFS_2K | EMAC_MR1_TR0_MULT)
+#else
+#define EMAC_MR1_RFS_4K 0x00180000
+#define EMAC_MR1_RFS_16K 0x00280000
+#define EMAC_RX_FIFO_SIZE(gige) ((gige) ? 16384 : 4096)
+#define EMAC_MR1_TFS_2K 0x00020000
+#define EMAC_MR1_TR 0x00008000
+#define EMAC_MR1_MWSW_001 0x00001000
+#define EMAC_MR1_JPSM 0x00000800
+#define EMAC_MR1_OBCI_MASK 0x00000038
+#define EMAC_MR1_OBCI_50 0x00000000
+#define EMAC_MR1_OBCI_66 0x00000008
+#define EMAC_MR1_OBCI_83 0x00000010
+#define EMAC_MR1_OBCI_100 0x00000018
+#define EMAC_MR1_OBCI_100P 0x00000020
+#define EMAC_MR1_OBCI(freq) ((freq) <= 50 ? EMAC_MR1_OBCI_50 : \
+ (freq) <= 66 ? EMAC_MR1_OBCI_66 : \
+ (freq) <= 83 ? EMAC_MR1_OBCI_83 : \
+ (freq) <= 100 ? EMAC_MR1_OBCI_100 : EMAC_MR1_OBCI_100P)
+#define EMAC_MR1_BASE(opb) (EMAC_MR1_TFS_2K | EMAC_MR1_TR | \
+ EMAC_MR1_MWSW_001 | EMAC_MR1_OBCI(opb))
+#endif
+
+/* EMACx_TMR0 */
+#define EMAC_TMR0_GNP 0x80000000
+#if !defined(CONFIG_IBM_EMAC4)
+#define EMAC_TMR0_DEFAULT 0x00000000
+#else
#define EMAC_TMR0_TFAE_2_32 0x00000001
#define EMAC_TMR0_TFAE_4_64 0x00000002
#define EMAC_TMR0_TFAE_8_128 0x00000003
#define EMAC_TMR0_TFAE_32_512 0x00000005
#define EMAC_TMR0_TFAE_64_1024 0x00000006
#define EMAC_TMR0_TFAE_128_2048 0x00000007
+#define EMAC_TMR0_DEFAULT EMAC_TMR0_TFAE_2_32
+#endif
+#define EMAC_TMR0_XMIT (EMAC_TMR0_GNP | EMAC_TMR0_DEFAULT)
+
+/* EMACx_TMR1 */
+
+/* IBM manuals are not very clear here.
+ * This is my interpretation of how things are. --ebs
+ */
+#if defined(CONFIG_40x)
+#define EMAC_FIFO_ENTRY_SIZE 8
+#define EMAC_MAL_BURST_SIZE (16 * 4)
+#else
+#define EMAC_FIFO_ENTRY_SIZE 16
+#define EMAC_MAL_BURST_SIZE (64 * 4)
+#endif
+
+#if !defined(CONFIG_IBM_EMAC4)
+#define EMAC_TMR1(l,h) (((l) << 27) | (((h) & 0xff) << 16))
+#else
+#define EMAC_TMR1(l,h) (((l) << 27) | (((h) & 0x3ff) << 14))
+#endif
-/* Receive Mode Register */
+/* EMACx_RMR */
#define EMAC_RMR_SP 0x80000000
#define EMAC_RMR_SFCS 0x40000000
-#define EMAC_RMR_ARRP 0x20000000
-#define EMAC_RMR_ARP 0x10000000
-#define EMAC_RMR_AROP 0x08000000
-#define EMAC_RMR_ARPI 0x04000000
+#define EMAC_RMR_RRP 0x20000000
+#define EMAC_RMR_RFP 0x10000000
+#define EMAC_RMR_ROP 0x08000000
+#define EMAC_RMR_RPIR 0x04000000
#define EMAC_RMR_PPP 0x02000000
#define EMAC_RMR_PME 0x01000000
#define EMAC_RMR_PMME 0x00800000
#define EMAC_RMR_MIAE 0x00200000
#define EMAC_RMR_BAE 0x00100000
#define EMAC_RMR_MAE 0x00080000
+#if !defined(CONFIG_IBM_EMAC4)
+#define EMAC_RMR_BASE 0x00000000
+#else
#define EMAC_RMR_RFAF_2_32 0x00000001
#define EMAC_RMR_RFAF_4_64 0x00000002
#define EMAC_RMR_RFAF_8_128 0x00000003
#define EMAC_RMR_RFAF_32_512 0x00000005
#define EMAC_RMR_RFAF_64_1024 0x00000006
#define EMAC_RMR_RFAF_128_2048 0x00000007
-#define EMAC_RMR_BASE (EMAC_RMR_IAE | EMAC_RMR_BAE)
+#define EMAC_RMR_BASE EMAC_RMR_RFAF_128_2048
+#endif
-/* Interrupt Status & enable Regs */
+/* EMACx_ISR & EMACx_ISER */
+#if !defined(CONFIG_IBM_EMAC4)
+#define EMAC_ISR_TXPE 0x00000000
+#define EMAC_ISR_RXPE 0x00000000
+#define EMAC_ISR_TXUE 0x00000000
+#define EMAC_ISR_RXOE 0x00000000
+#else
+#define EMAC_ISR_TXPE 0x20000000
+#define EMAC_ISR_RXPE 0x10000000
+#define EMAC_ISR_TXUE 0x08000000
+#define EMAC_ISR_RXOE 0x04000000
+#endif
#define EMAC_ISR_OVR 0x02000000
#define EMAC_ISR_PP 0x01000000
#define EMAC_ISR_BP 0x00800000
#define EMAC_ISR_PTLE 0x00040000
#define EMAC_ISR_ORE 0x00020000
#define EMAC_ISR_IRE 0x00010000
-#define EMAC_ISR_DBDM 0x00000200
-#define EMAC_ISR_DB0 0x00000100
-#define EMAC_ISR_SE0 0x00000080
-#define EMAC_ISR_TE0 0x00000040
-#define EMAC_ISR_DB1 0x00000020
-#define EMAC_ISR_SE1 0x00000010
-#define EMAC_ISR_TE1 0x00000008
+#define EMAC_ISR_SQE 0x00000080
+#define EMAC_ISR_TE 0x00000040
#define EMAC_ISR_MOS 0x00000002
#define EMAC_ISR_MOF 0x00000001
-/* STA CONTROL REG */
+/* EMACx_STACR */
+#define EMAC_STACR_PHYD_MASK 0xffff
+#define EMAC_STACR_PHYD_SHIFT 16
#define EMAC_STACR_OC 0x00008000
#define EMAC_STACR_PHYE 0x00004000
-#define EMAC_STACR_WRITE 0x00002000
-#define EMAC_STACR_READ 0x00001000
-#define EMAC_STACR_CLK_83MHZ 0x00000800 /* 0's for 50Mhz */
-#define EMAC_STACR_CLK_66MHZ 0x00000400
-#define EMAC_STACR_CLK_100MHZ 0x00000C00
+#define EMAC_STACR_STAC_MASK 0x00003000
+#define EMAC_STACR_STAC_READ 0x00001000
+#define EMAC_STACR_STAC_WRITE 0x00002000
+#if !defined(CONFIG_IBM_EMAC4)
+#define EMAC_STACR_OPBC_MASK 0x00000C00
+#define EMAC_STACR_OPBC_50 0x00000000
+#define EMAC_STACR_OPBC_66 0x00000400
+#define EMAC_STACR_OPBC_83 0x00000800
+#define EMAC_STACR_OPBC_100 0x00000C00
+#define EMAC_STACR_OPBC(freq) ((freq) <= 50 ? EMAC_STACR_OPBC_50 : \
+ (freq) <= 66 ? EMAC_STACR_OPBC_66 : \
+ (freq) <= 83 ? EMAC_STACR_OPBC_83 : EMAC_STACR_OPBC_100)
+#define EMAC_STACR_BASE(opb) EMAC_STACR_OPBC(opb)
+#else
+#define EMAC_STACR_BASE(opb) 0x00000000
+#endif
+#define EMAC_STACR_PCDA_MASK 0x1f
+#define EMAC_STACR_PCDA_SHIFT 5
+#define EMAC_STACR_PRA_MASK 0x1f
+
+/* EMACx_TRTR */
+#if !defined(CONFIG_IBM_EMAC4)
+#define EMAC_TRTR_SHIFT 27
+#else
+#define EMAC_TRTR_SHIFT 24
+#endif
+#define EMAC_TRTR(size) ((((size) >> 6) - 1) << EMAC_TRTR_SHIFT)
-/* Transmit Request Threshold Register */
-#define EMAC_TRTR_1600 0x18000000 /* 0's for 64 Bytes */
-#define EMAC_TRTR_1024 0x0f000000
-#define EMAC_TRTR_512 0x07000000
-#define EMAC_TRTR_256 0x03000000
-#define EMAC_TRTR_192 0x10000000
-#define EMAC_TRTR_128 0x01000000
+/* EMACx_RWMR */
+#if !defined(CONFIG_IBM_EMAC4)
+#define EMAC_RWMR(l,h) (((l) << 23) | ( ((h) & 0x1ff) << 7))
+#else
+#define EMAC_RWMR(l,h) (((l) << 22) | ( ((h) & 0x3ff) << 6))
+#endif
+/* EMAC specific TX descriptor control fields (write access) */
#define EMAC_TX_CTRL_GFCS 0x0200
#define EMAC_TX_CTRL_GP 0x0100
#define EMAC_TX_CTRL_ISA 0x0080
#define EMAC_TX_CTRL_RSA 0x0040
#define EMAC_TX_CTRL_IVT 0x0020
#define EMAC_TX_CTRL_RVT 0x0010
-#define EMAC_TX_CTRL_TAH_CSUM 0x000e /* TAH only */
-#define EMAC_TX_CTRL_TAH_SEG4 0x000a /* TAH only */
-#define EMAC_TX_CTRL_TAH_SEG3 0x0008 /* TAH only */
-#define EMAC_TX_CTRL_TAH_SEG2 0x0006 /* TAH only */
-#define EMAC_TX_CTRL_TAH_SEG1 0x0004 /* TAH only */
-#define EMAC_TX_CTRL_TAH_SEG0 0x0002 /* TAH only */
-#define EMAC_TX_CTRL_TAH_DIS 0x0000 /* TAH only */
+#define EMAC_TX_CTRL_TAH_CSUM 0x000e
-#define EMAC_TX_CTRL_DFLT ( \
- MAL_TX_CTRL_INTR | EMAC_TX_CTRL_GFCS | EMAC_TX_CTRL_GP )
-
-/* madmal transmit status / Control bits */
+/* EMAC specific TX descriptor status fields (read access) */
#define EMAC_TX_ST_BFCS 0x0200
-#define EMAC_TX_ST_BPP 0x0100
#define EMAC_TX_ST_LCS 0x0080
#define EMAC_TX_ST_ED 0x0040
#define EMAC_TX_ST_EC 0x0020
#define EMAC_TX_ST_SC 0x0004
#define EMAC_TX_ST_UR 0x0002
#define EMAC_TX_ST_SQE 0x0001
+#if !defined(CONFIG_IBM_EMAC_TAH)
+#define EMAC_IS_BAD_TX(v) ((v) & (EMAC_TX_ST_LCS | EMAC_TX_ST_ED | \
+ EMAC_TX_ST_EC | EMAC_TX_ST_LC | \
+ EMAC_TX_ST_MC | EMAC_TX_ST_UR))
+#else
+#define EMAC_IS_BAD_TX(v) ((v) & (EMAC_TX_ST_LCS | EMAC_TX_ST_ED | \
+ EMAC_TX_ST_EC | EMAC_TX_ST_LC))
+#endif
-/* madmal receive status / Control bits */
+/* EMAC specific RX descriptor status fields (read access) */
#define EMAC_RX_ST_OE 0x0200
#define EMAC_RX_ST_PP 0x0100
#define EMAC_RX_ST_BP 0x0080
#define EMAC_RX_ST_PTL 0x0004
#define EMAC_RX_ST_ORE 0x0002
#define EMAC_RX_ST_IRE 0x0001
-#define EMAC_BAD_RX_PACKET 0x02ff
-#define EMAC_CSUM_VER_ERROR 0x0003
-
-/* identify a bad rx packet dependent on emac features */
-#ifdef CONFIG_IBM_EMAC4
-#define EMAC_IS_BAD_RX_PACKET(desc) \
- (((desc & (EMAC_BAD_RX_PACKET & ~EMAC_CSUM_VER_ERROR)) || \
- ((desc & EMAC_CSUM_VER_ERROR) == EMAC_RX_ST_ORE) || \
- ((desc & EMAC_CSUM_VER_ERROR) == EMAC_RX_ST_IRE)))
-#else
-#define EMAC_IS_BAD_RX_PACKET(desc) \
- (desc & EMAC_BAD_RX_PACKET)
-#endif
-
-/* SoC implementation specific EMAC register defaults */
-#if defined(CONFIG_440GP)
-#define EMAC_RWMR_DEFAULT 0x80009000
-#define EMAC_TMR0_DEFAULT 0x00000000
-#define EMAC_TMR1_DEFAULT 0xf8640000
-#elif defined(CONFIG_440GX)
-#define EMAC_RWMR_DEFAULT 0x1000a200
-#define EMAC_TMR0_DEFAULT EMAC_TMR0_TFAE_2_32
-#define EMAC_TMR1_DEFAULT 0xa00f0000
-#elif defined(CONFIG_440SP)
-#define EMAC_RWMR_DEFAULT 0x08002000
-#define EMAC_TMR0_DEFAULT EMAC_TMR0_TFAE_128_2048
-#define EMAC_TMR1_DEFAULT 0xf8200000
-#else
-#define EMAC_RWMR_DEFAULT 0x0f002000
-#define EMAC_TMR0_DEFAULT 0x00000000
-#define EMAC_TMR1_DEFAULT 0x380f0000
-#endif /* CONFIG_440GP */
-
-/* Revision specific EMAC register defaults */
-#ifdef CONFIG_IBM_EMAC4
-#define EMAC_M1_DEFAULT (EMAC_M1_BASE | \
- EMAC_M1_OPB_CLK_83 | \
- EMAC_M1_TX_MWSW)
-#define EMAC_RMR_DEFAULT (EMAC_RMR_BASE | \
- EMAC_RMR_RFAF_128_2048)
-#define EMAC_TMR0_XMIT (EMAC_TMR0_GNP0 | \
- EMAC_TMR0_DEFAULT)
-#define EMAC_TRTR_DEFAULT EMAC_TRTR_1024
-#else /* !CONFIG_IBM_EMAC4 */
-#define EMAC_M1_DEFAULT EMAC_M1_BASE
-#define EMAC_RMR_DEFAULT EMAC_RMR_BASE
-#define EMAC_TMR0_XMIT EMAC_TMR0_GNP0
-#define EMAC_TRTR_DEFAULT EMAC_TRTR_1600
-#endif /* CONFIG_IBM_EMAC4 */
-
-#endif
+#define EMAC_RX_TAH_BAD_CSUM 0x0003
+#define EMAC_BAD_RX_MASK (EMAC_RX_ST_OE | EMAC_RX_ST_BP | \
+ EMAC_RX_ST_RP | EMAC_RX_ST_SE | \
+ EMAC_RX_ST_AE | EMAC_RX_ST_BFCS | \
+ EMAC_RX_ST_PTL | EMAC_RX_ST_ORE | \
+ EMAC_RX_ST_IRE )
+#endif /* __IBM_EMAC_H_ */
/*
- * ibm_emac_core.c
+ * drivers/net/ibm_emac/ibm_emac_core.c
*
- * Ethernet driver for the built in ethernet on the IBM 4xx PowerPC
- * processors.
- *
- * (c) 2003 Benjamin Herrenschmidt <benh@kernel.crashing.org>
+ * Driver for PowerPC 4xx on-chip ethernet controller.
*
- * Based on original work by
+ * Copyright (c) 2004, 2005 Zultys Technologies.
+ * Eugene Surovegin <eugene.surovegin@zultys.com> or <ebs@ebshome.net>
*
+ * Based on original work by
+ * Matt Porter <mporter@kernel.crashing.org>
+ * (c) 2003 Benjamin Herrenschmidt <benh@kernel.crashing.org>
* Armin Kuster <akuster@mvista.com>
* Johnnie Peters <jpeters@mvista.com>
*
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
- * TODO
- * - Check for races in the "remove" code path
- * - Add some Power Management to the MAC and the PHY
- * - Audit remaining of non-rewritten code (--BenH)
- * - Cleanup message display using msglevel mecanism
- * - Address all errata
- * - Audit all register update paths to ensure they
- * are being written post soft reset if required.
+ *
*/
+
+#include <linux/config.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/sched.h>
#include <linux/string.h>
-#include <linux/timer.h>
-#include <linux/ptrace.h>
#include <linux/errno.h>
-#include <linux/ioport.h>
-#include <linux/slab.h>
#include <linux/interrupt.h>
#include <linux/delay.h>
#include <linux/init.h>
#include <linux/types.h>
-#include <linux/dma-mapping.h>
+#include <linux/pci.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/skbuff.h>
+#include <linux/crc32.h>
#include <linux/ethtool.h>
#include <linux/mii.h>
#include <linux/bitops.h>
#include <asm/processor.h>
#include <asm/io.h>
#include <asm/dma.h>
-#include <asm/irq.h>
#include <asm/uaccess.h>
#include <asm/ocp.h>
-#include <linux/netdevice.h>
-#include <linux/etherdevice.h>
-#include <linux/skbuff.h>
-#include <linux/crc32.h>
-
#include "ibm_emac_core.h"
-
-//#define MDIO_DEBUG(fmt) printk fmt
-#define MDIO_DEBUG(fmt)
-
-//#define LINK_DEBUG(fmt) printk fmt
-#define LINK_DEBUG(fmt)
-
-//#define PKT_DEBUG(fmt) printk fmt
-#define PKT_DEBUG(fmt)
-
-#define DRV_NAME "emac"
-#define DRV_VERSION "2.0"
-#define DRV_AUTHOR "Benjamin Herrenschmidt <benh@kernel.crashing.org>"
-#define DRV_DESC "IBM EMAC Ethernet driver"
+#include "ibm_emac_debug.h"
/*
- * When mdio_idx >= 0, contains a list of emac ocp_devs
- * that have had their initialization deferred until the
- * common MDIO controller has been initialized.
+ * Lack of dma_unmap_???? calls is intentional.
+ *
+ * API-correct usage requires additional support state information to be
+ * maintained for every RX and TX buffer descriptor (BD). Unfortunately, due to
+ * EMAC design (e.g. TX buffer passed from network stack can be split into
+ * several BDs, dma_map_single/dma_map_page can be used to map particular BD),
+ * maintaining such information will add additional overhead.
+ * Current DMA API implementation for 4xx processors only ensures cache coherency
+ * and dma_unmap_???? routines are empty and are likely to stay this way.
+ * I decided to omit dma_unmap_??? calls because I don't want to add additional
+ * complexity just for the sake of following some abstract API, when it doesn't
+ * add any real benefit to the driver. I understand that this decision maybe
+ * controversial, but I really tried to make code API-correct and efficient
+ * at the same time and didn't come up with code I liked :(. --ebs
*/
-LIST_HEAD(emac_init_list);
-MODULE_AUTHOR(DRV_AUTHOR);
+#define DRV_NAME "emac"
+#define DRV_VERSION "3.53"
+#define DRV_DESC "PPC 4xx OCP EMAC driver"
+
MODULE_DESCRIPTION(DRV_DESC);
+MODULE_AUTHOR
+ ("Eugene Surovegin <eugene.surovegin@zultys.com> or <ebs@ebshome.net>");
MODULE_LICENSE("GPL");
-static int skb_res = SKB_RES;
-module_param(skb_res, int, 0444);
-MODULE_PARM_DESC(skb_res, "Amount of data to reserve on skb buffs\n"
- "The 405 handles a misaligned IP header fine but\n"
- "this can help if you are routing to a tunnel or a\n"
- "device that needs aligned data. 0..2");
+/* minimum number of free TX descriptors required to wake up TX process */
+#define EMAC_TX_WAKEUP_THRESH (NUM_TX_BUFF / 4)
-#define RGMII_PRIV(ocpdev) ((struct ibm_ocp_rgmii*)ocp_get_drvdata(ocpdev))
-
-static unsigned int rgmii_enable[] = {
- RGMII_RTBI,
- RGMII_RGMII,
- RGMII_TBI,
- RGMII_GMII
-};
+/* If packet size is less than this number, we allocate small skb and copy packet
+ * contents into it instead of just sending original big skb up
+ */
+#define EMAC_RX_COPY_THRESH CONFIG_IBM_EMAC_RX_COPY_THRESHOLD
-static unsigned int rgmii_speed_mask[] = {
- RGMII_MII2_SPDMASK,
- RGMII_MII3_SPDMASK
-};
+/* Since multiple EMACs share MDIO lines in various ways, we need
+ * to avoid re-using the same PHY ID in cases where the arch didn't
+ * setup precise phy_map entries
+ */
+static u32 busy_phy_map;
-static unsigned int rgmii_speed100[] = {
- RGMII_MII2_100MB,
- RGMII_MII3_100MB
-};
+#if defined(CONFIG_IBM_EMAC_PHY_RX_CLK_FIX) && (defined(CONFIG_405EP) || defined(CONFIG_440EP))
+/* 405EP has "EMAC to PHY Control Register" (CPC0_EPCTL) which can help us
+ * with PHY RX clock problem.
+ * 440EP has more sane SDR0_MFR register implementation than 440GX, which
+ * also allows controlling each EMAC clock
+ */
+static inline void EMAC_RX_CLK_TX(int idx)
+{
+ unsigned long flags;
+ local_irq_save(flags);
-static unsigned int rgmii_speed1000[] = {
- RGMII_MII2_1000MB,
- RGMII_MII3_1000MB
-};
+#if defined(CONFIG_405EP)
+ mtdcr(0xf3, mfdcr(0xf3) | (1 << idx));
+#else /* CONFIG_440EP */
+ SDR_WRITE(DCRN_SDR_MFR, SDR_READ(DCRN_SDR_MFR) | (0x08000000 >> idx));
+#endif
-#define ZMII_PRIV(ocpdev) ((struct ibm_ocp_zmii*)ocp_get_drvdata(ocpdev))
+ local_irq_restore(flags);
+}
-static unsigned int zmii_enable[][4] = {
- {ZMII_SMII0, ZMII_RMII0, ZMII_MII0,
- ~(ZMII_MDI1 | ZMII_MDI2 | ZMII_MDI3)},
- {ZMII_SMII1, ZMII_RMII1, ZMII_MII1,
- ~(ZMII_MDI0 | ZMII_MDI2 | ZMII_MDI3)},
- {ZMII_SMII2, ZMII_RMII2, ZMII_MII2,
- ~(ZMII_MDI0 | ZMII_MDI1 | ZMII_MDI3)},
- {ZMII_SMII3, ZMII_RMII3, ZMII_MII3, ~(ZMII_MDI0 | ZMII_MDI1 | ZMII_MDI2)}
-};
+static inline void EMAC_RX_CLK_DEFAULT(int idx)
+{
+ unsigned long flags;
+ local_irq_save(flags);
-static unsigned int mdi_enable[] = {
- ZMII_MDI0,
- ZMII_MDI1,
- ZMII_MDI2,
- ZMII_MDI3
-};
+#if defined(CONFIG_405EP)
+ mtdcr(0xf3, mfdcr(0xf3) & ~(1 << idx));
+#else /* CONFIG_440EP */
+ SDR_WRITE(DCRN_SDR_MFR, SDR_READ(DCRN_SDR_MFR) & ~(0x08000000 >> idx));
+#endif
-static unsigned int zmii_speed = 0x0;
-static unsigned int zmii_speed100[] = {
- ZMII_MII0_100MB,
- ZMII_MII1_100MB,
- ZMII_MII2_100MB,
- ZMII_MII3_100MB
-};
+ local_irq_restore(flags);
+}
+#else
+#define EMAC_RX_CLK_TX(idx) ((void)0)
+#define EMAC_RX_CLK_DEFAULT(idx) ((void)0)
+#endif
-/* Since multiple EMACs share MDIO lines in various ways, we need
- * to avoid re-using the same PHY ID in cases where the arch didn't
- * setup precise phy_map entries
+#if defined(CONFIG_IBM_EMAC_PHY_RX_CLK_FIX) && defined(CONFIG_440GX)
+/* We can switch Ethernet clock to the internal source through SDR0_MFR[ECS],
+ * unfortunately this is less flexible than 440EP case, because it's a global
+ * setting for all EMACs, therefore we do this clock trick only during probe.
*/
-static u32 busy_phy_map = 0;
+#define EMAC_CLK_INTERNAL SDR_WRITE(DCRN_SDR_MFR, \
+ SDR_READ(DCRN_SDR_MFR) | 0x08000000)
+#define EMAC_CLK_EXTERNAL SDR_WRITE(DCRN_SDR_MFR, \
+ SDR_READ(DCRN_SDR_MFR) & ~0x08000000)
+#else
+#define EMAC_CLK_INTERNAL ((void)0)
+#define EMAC_CLK_EXTERNAL ((void)0)
+#endif
-/* If EMACs share a common MDIO device, this points to it */
-static struct net_device *mdio_ndev = NULL;
+/* I don't want to litter system log with timeout errors
+ * when we have brain-damaged PHY.
+ */
+static inline void emac_report_timeout_error(struct ocp_enet_private *dev,
+ const char *error)
+{
+#if defined(CONFIG_IBM_EMAC_PHY_RX_CLK_FIX)
+ DBG("%d: %s" NL, dev->def->index, error);
+#else
+ if (net_ratelimit())
+ printk(KERN_ERR "emac%d: %s\n", dev->def->index, error);
+#endif
+}
-struct emac_def_dev {
- struct list_head link;
- struct ocp_device *ocpdev;
- struct ibm_ocp_mal *mal;
+/* PHY polling intervals */
+#define PHY_POLL_LINK_ON HZ
+#define PHY_POLL_LINK_OFF (HZ / 5)
+
+/* Please, keep in sync with struct ibm_emac_stats/ibm_emac_error_stats */
+static const char emac_stats_keys[EMAC_ETHTOOL_STATS_COUNT][ETH_GSTRING_LEN] = {
+ "rx_packets", "rx_bytes", "tx_packets", "tx_bytes", "rx_packets_csum",
+ "tx_packets_csum", "tx_undo", "rx_dropped_stack", "rx_dropped_oom",
+ "rx_dropped_error", "rx_dropped_resize", "rx_dropped_mtu",
+ "rx_stopped", "rx_bd_errors", "rx_bd_overrun", "rx_bd_bad_packet",
+ "rx_bd_runt_packet", "rx_bd_short_event", "rx_bd_alignment_error",
+ "rx_bd_bad_fcs", "rx_bd_packet_too_long", "rx_bd_out_of_range",
+ "rx_bd_in_range", "rx_parity", "rx_fifo_overrun", "rx_overrun",
+ "rx_bad_packet", "rx_runt_packet", "rx_short_event",
+ "rx_alignment_error", "rx_bad_fcs", "rx_packet_too_long",
+ "rx_out_of_range", "rx_in_range", "tx_dropped", "tx_bd_errors",
+ "tx_bd_bad_fcs", "tx_bd_carrier_loss", "tx_bd_excessive_deferral",
+ "tx_bd_excessive_collisions", "tx_bd_late_collision",
+ "tx_bd_multple_collisions", "tx_bd_single_collision",
+ "tx_bd_underrun", "tx_bd_sqe", "tx_parity", "tx_underrun", "tx_sqe",
+ "tx_errors"
};
-static struct net_device_stats *emac_stats(struct net_device *dev)
+static irqreturn_t emac_irq(int irq, void *dev_instance, struct pt_regs *regs);
+static void emac_clean_tx_ring(struct ocp_enet_private *dev);
+
+static inline int emac_phy_supports_gige(int phy_mode)
{
- struct ocp_enet_private *fep = dev->priv;
- return &fep->stats;
-};
+ return phy_mode == PHY_MODE_GMII ||
+ phy_mode == PHY_MODE_RGMII ||
+ phy_mode == PHY_MODE_TBI ||
+ phy_mode == PHY_MODE_RTBI;
+}
-static int
-emac_init_rgmii(struct ocp_device *rgmii_dev, int input, int phy_mode)
+static inline int emac_phy_gpcs(int phy_mode)
{
- struct ibm_ocp_rgmii *rgmii = RGMII_PRIV(rgmii_dev);
- const char *mode_name[] = { "RTBI", "RGMII", "TBI", "GMII" };
- int mode = -1;
+ return phy_mode == PHY_MODE_TBI ||
+ phy_mode == PHY_MODE_RTBI;
+}
- if (!rgmii) {
- rgmii = kmalloc(sizeof(struct ibm_ocp_rgmii), GFP_KERNEL);
+static inline void emac_tx_enable(struct ocp_enet_private *dev)
+{
+ struct emac_regs *p = dev->emacp;
+ unsigned long flags;
+ u32 r;
- if (rgmii == NULL) {
- printk(KERN_ERR
- "rgmii%d: Out of memory allocating RGMII structure!\n",
- rgmii_dev->def->index);
- return -ENOMEM;
- }
+ local_irq_save(flags);
- memset(rgmii, 0, sizeof(*rgmii));
+ DBG("%d: tx_enable" NL, dev->def->index);
- rgmii->base =
- (struct rgmii_regs *)ioremap(rgmii_dev->def->paddr,
- sizeof(*rgmii->base));
- if (rgmii->base == NULL) {
- printk(KERN_ERR
- "rgmii%d: Cannot ioremap bridge registers!\n",
- rgmii_dev->def->index);
+ r = in_be32(&p->mr0);
+ if (!(r & EMAC_MR0_TXE))
+ out_be32(&p->mr0, r | EMAC_MR0_TXE);
+ local_irq_restore(flags);
+}
- kfree(rgmii);
- return -ENOMEM;
- }
- ocp_set_drvdata(rgmii_dev, rgmii);
- }
+static void emac_tx_disable(struct ocp_enet_private *dev)
+{
+ struct emac_regs *p = dev->emacp;
+ unsigned long flags;
+ u32 r;
- if (phy_mode) {
- switch (phy_mode) {
- case PHY_MODE_GMII:
- mode = GMII;
- break;
- case PHY_MODE_TBI:
- mode = TBI;
- break;
- case PHY_MODE_RTBI:
- mode = RTBI;
- break;
- case PHY_MODE_RGMII:
- default:
- mode = RGMII;
- }
- rgmii->base->fer &= ~RGMII_FER_MASK(input);
- rgmii->base->fer |= rgmii_enable[mode] << (4 * input);
- } else {
- switch ((rgmii->base->fer & RGMII_FER_MASK(input)) >> (4 *
- input)) {
- case RGMII_RTBI:
- mode = RTBI;
- break;
- case RGMII_RGMII:
- mode = RGMII;
- break;
- case RGMII_TBI:
- mode = TBI;
- break;
- case RGMII_GMII:
- mode = GMII;
- }
- }
+ local_irq_save(flags);
- /* Set mode to RGMII if nothing valid is detected */
- if (mode < 0)
- mode = RGMII;
+ DBG("%d: tx_disable" NL, dev->def->index);
+
+ r = in_be32(&p->mr0);
+ if (r & EMAC_MR0_TXE) {
+ int n = 300;
+ out_be32(&p->mr0, r & ~EMAC_MR0_TXE);
+ while (!(in_be32(&p->mr0) & EMAC_MR0_TXI) && n)
+ --n;
+ if (unlikely(!n))
+ emac_report_timeout_error(dev, "TX disable timeout");
+ }
+ local_irq_restore(flags);
+}
- printk(KERN_NOTICE "rgmii%d: input %d in %s mode\n",
- rgmii_dev->def->index, input, mode_name[mode]);
+static void emac_rx_enable(struct ocp_enet_private *dev)
+{
+ struct emac_regs *p = dev->emacp;
+ unsigned long flags;
+ u32 r;
- rgmii->mode[input] = mode;
- rgmii->users++;
+ local_irq_save(flags);
+ if (unlikely(dev->commac.rx_stopped))
+ goto out;
- return 0;
+ DBG("%d: rx_enable" NL, dev->def->index);
+
+ r = in_be32(&p->mr0);
+ if (!(r & EMAC_MR0_RXE)) {
+ if (unlikely(!(r & EMAC_MR0_RXI))) {
+ /* Wait if previous async disable is still in progress */
+ int n = 100;
+ while (!(r = in_be32(&p->mr0) & EMAC_MR0_RXI) && n)
+ --n;
+ if (unlikely(!n))
+ emac_report_timeout_error(dev,
+ "RX disable timeout");
+ }
+ out_be32(&p->mr0, r | EMAC_MR0_RXE);
+ }
+ out:
+ local_irq_restore(flags);
}
-static void
-emac_rgmii_port_speed(struct ocp_device *ocpdev, int input, int speed)
+static void emac_rx_disable(struct ocp_enet_private *dev)
{
- struct ibm_ocp_rgmii *rgmii = RGMII_PRIV(ocpdev);
- unsigned int rgmii_speed;
-
- rgmii_speed = in_be32(&rgmii->base->ssr);
+ struct emac_regs *p = dev->emacp;
+ unsigned long flags;
+ u32 r;
- rgmii_speed &= ~rgmii_speed_mask[input];
+ local_irq_save(flags);
- if (speed == 1000)
- rgmii_speed |= rgmii_speed1000[input];
- else if (speed == 100)
- rgmii_speed |= rgmii_speed100[input];
+ DBG("%d: rx_disable" NL, dev->def->index);
- out_be32(&rgmii->base->ssr, rgmii_speed);
+ r = in_be32(&p->mr0);
+ if (r & EMAC_MR0_RXE) {
+ int n = 300;
+ out_be32(&p->mr0, r & ~EMAC_MR0_RXE);
+ while (!(in_be32(&p->mr0) & EMAC_MR0_RXI) && n)
+ --n;
+ if (unlikely(!n))
+ emac_report_timeout_error(dev, "RX disable timeout");
+ }
+ local_irq_restore(flags);
}
-static void emac_close_rgmii(struct ocp_device *ocpdev)
+static inline void emac_rx_disable_async(struct ocp_enet_private *dev)
{
- struct ibm_ocp_rgmii *rgmii = RGMII_PRIV(ocpdev);
- BUG_ON(!rgmii || rgmii->users == 0);
+ struct emac_regs *p = dev->emacp;
+ unsigned long flags;
+ u32 r;
- if (!--rgmii->users) {
- ocp_set_drvdata(ocpdev, NULL);
- iounmap((void *)rgmii->base);
- kfree(rgmii);
- }
+ local_irq_save(flags);
+
+ DBG("%d: rx_disable_async" NL, dev->def->index);
+
+ r = in_be32(&p->mr0);
+ if (r & EMAC_MR0_RXE)
+ out_be32(&p->mr0, r & ~EMAC_MR0_RXE);
+ local_irq_restore(flags);
}
-static int emac_init_zmii(struct ocp_device *zmii_dev, int input, int phy_mode)
+static int emac_reset(struct ocp_enet_private *dev)
{
- struct ibm_ocp_zmii *zmii = ZMII_PRIV(zmii_dev);
- const char *mode_name[] = { "SMII", "RMII", "MII" };
- int mode = -1;
+ struct emac_regs *p = dev->emacp;
+ unsigned long flags;
+ int n = 20;
- if (!zmii) {
- zmii = kmalloc(sizeof(struct ibm_ocp_zmii), GFP_KERNEL);
- if (zmii == NULL) {
- printk(KERN_ERR
- "zmii%d: Out of memory allocating ZMII structure!\n",
- zmii_dev->def->index);
- return -ENOMEM;
- }
- memset(zmii, 0, sizeof(*zmii));
+ DBG("%d: reset" NL, dev->def->index);
- zmii->base =
- (struct zmii_regs *)ioremap(zmii_dev->def->paddr,
- sizeof(*zmii->base));
- if (zmii->base == NULL) {
- printk(KERN_ERR
- "zmii%d: Cannot ioremap bridge registers!\n",
- zmii_dev->def->index);
+ local_irq_save(flags);
- kfree(zmii);
- return -ENOMEM;
- }
- ocp_set_drvdata(zmii_dev, zmii);
+ if (!dev->reset_failed) {
+ /* 40x erratum suggests stopping RX channel before reset,
+ * we stop TX as well
+ */
+ emac_rx_disable(dev);
+ emac_tx_disable(dev);
}
- if (phy_mode) {
- switch (phy_mode) {
- case PHY_MODE_MII:
- mode = MII;
- break;
- case PHY_MODE_RMII:
- mode = RMII;
- break;
- case PHY_MODE_SMII:
- default:
- mode = SMII;
- }
- zmii->base->fer &= ~ZMII_FER_MASK(input);
- zmii->base->fer |= zmii_enable[input][mode];
+ out_be32(&p->mr0, EMAC_MR0_SRST);
+ while ((in_be32(&p->mr0) & EMAC_MR0_SRST) && n)
+ --n;
+ local_irq_restore(flags);
+
+ if (n) {
+ dev->reset_failed = 0;
+ return 0;
} else {
- switch ((zmii->base->fer & ZMII_FER_MASK(input)) << (4 * input)) {
- case ZMII_MII0:
- mode = MII;
- break;
- case ZMII_RMII0:
- mode = RMII;
- break;
- case ZMII_SMII0:
- mode = SMII;
- }
+ emac_report_timeout_error(dev, "reset timeout");
+ dev->reset_failed = 1;
+ return -ETIMEDOUT;
}
+}
- /* Set mode to SMII if nothing valid is detected */
- if (mode < 0)
- mode = SMII;
+static void emac_hash_mc(struct ocp_enet_private *dev)
+{
+ struct emac_regs *p = dev->emacp;
+ u16 gaht[4] = { 0 };
+ struct dev_mc_list *dmi;
- printk(KERN_NOTICE "zmii%d: input %d in %s mode\n",
- zmii_dev->def->index, input, mode_name[mode]);
+ DBG("%d: hash_mc %d" NL, dev->def->index, dev->ndev->mc_count);
- zmii->mode[input] = mode;
- zmii->users++;
+ for (dmi = dev->ndev->mc_list; dmi; dmi = dmi->next) {
+ int bit;
+ DBG2("%d: mc %02x:%02x:%02x:%02x:%02x:%02x" NL,
+ dev->def->index,
+ dmi->dmi_addr[0], dmi->dmi_addr[1], dmi->dmi_addr[2],
+ dmi->dmi_addr[3], dmi->dmi_addr[4], dmi->dmi_addr[5]);
- return 0;
+ bit = 63 - (ether_crc(ETH_ALEN, dmi->dmi_addr) >> 26);
+ gaht[bit >> 4] |= 0x8000 >> (bit & 0x0f);
+ }
+ out_be32(&p->gaht1, gaht[0]);
+ out_be32(&p->gaht2, gaht[1]);
+ out_be32(&p->gaht3, gaht[2]);
+ out_be32(&p->gaht4, gaht[3]);
}
-static void emac_enable_zmii_port(struct ocp_device *ocpdev, int input)
+static inline u32 emac_iff2rmr(struct net_device *ndev)
{
- u32 mask;
- struct ibm_ocp_zmii *zmii = ZMII_PRIV(ocpdev);
+ u32 r = EMAC_RMR_SP | EMAC_RMR_SFCS | EMAC_RMR_IAE | EMAC_RMR_BAE |
+ EMAC_RMR_BASE;
+
+ if (ndev->flags & IFF_PROMISC)
+ r |= EMAC_RMR_PME;
+ else if (ndev->flags & IFF_ALLMULTI || ndev->mc_count > 32)
+ r |= EMAC_RMR_PMME;
+ else if (ndev->mc_count > 0)
+ r |= EMAC_RMR_MAE;
- mask = in_be32(&zmii->base->fer);
- mask &= zmii_enable[input][MDI]; /* turn all non enabled MDI's off */
- mask |= zmii_enable[input][zmii->mode[input]] | mdi_enable[input];
- out_be32(&zmii->base->fer, mask);
+ return r;
}
-static void
-emac_zmii_port_speed(struct ocp_device *ocpdev, int input, int speed)
+static inline int emac_opb_mhz(void)
{
- struct ibm_ocp_zmii *zmii = ZMII_PRIV(ocpdev);
-
- if (speed == 100)
- zmii_speed |= zmii_speed100[input];
- else
- zmii_speed &= ~zmii_speed100[input];
-
- out_be32(&zmii->base->ssr, zmii_speed);
+ return (ocp_sys_info.opb_bus_freq + 500000) / 1000000;
}
-static void emac_close_zmii(struct ocp_device *ocpdev)
+/* BHs disabled */
+static int emac_configure(struct ocp_enet_private *dev)
{
- struct ibm_ocp_zmii *zmii = ZMII_PRIV(ocpdev);
- BUG_ON(!zmii || zmii->users == 0);
+ struct emac_regs *p = dev->emacp;
+ struct net_device *ndev = dev->ndev;
+ int gige;
+ u32 r;
- if (!--zmii->users) {
- ocp_set_drvdata(ocpdev, NULL);
- iounmap((void *)zmii->base);
- kfree(zmii);
- }
-}
+ DBG("%d: configure" NL, dev->def->index);
-int emac_phy_read(struct net_device *dev, int mii_id, int reg)
-{
- int count;
- uint32_t stacr;
- struct ocp_enet_private *fep = dev->priv;
- emac_t *emacp = fep->emacp;
+ if (emac_reset(dev) < 0)
+ return -ETIMEDOUT;
- MDIO_DEBUG(("%s: phy_read, id: 0x%x, reg: 0x%x\n", dev->name, mii_id,
- reg));
+ tah_reset(dev->tah_dev);
- /* Enable proper ZMII port */
- if (fep->zmii_dev)
- emac_enable_zmii_port(fep->zmii_dev, fep->zmii_input);
+ /* Mode register */
+ r = EMAC_MR1_BASE(emac_opb_mhz()) | EMAC_MR1_VLE | EMAC_MR1_IST;
+ if (dev->phy.duplex == DUPLEX_FULL)
+ r |= EMAC_MR1_FDE;
+ switch (dev->phy.speed) {
+ case SPEED_1000:
+ if (emac_phy_gpcs(dev->phy.mode)) {
+ r |= EMAC_MR1_MF_1000GPCS |
+ EMAC_MR1_MF_IPPA(dev->phy.address);
- /* Use the EMAC that has the MDIO port */
- if (fep->mdio_dev) {
- dev = fep->mdio_dev;
- fep = dev->priv;
- emacp = fep->emacp;
+ /* Put some arbitrary OUI, Manuf & Rev IDs so we can
+ * identify this GPCS PHY later.
+ */
+ out_be32(&p->ipcr, 0xdeadbeef);
+ } else
+ r |= EMAC_MR1_MF_1000;
+ r |= EMAC_MR1_RFS_16K;
+ gige = 1;
+
+ if (dev->ndev->mtu > ETH_DATA_LEN)
+ r |= EMAC_MR1_JPSM;
+ break;
+ case SPEED_100:
+ r |= EMAC_MR1_MF_100;
+ /* Fall through */
+ default:
+ r |= EMAC_MR1_RFS_4K;
+ gige = 0;
+ break;
}
- count = 0;
- while ((((stacr = in_be32(&emacp->em0stacr)) & EMAC_STACR_OC) == 0)
- && (count++ < MDIO_DELAY))
- udelay(1);
- MDIO_DEBUG((" (count was %d)\n", count));
+ if (dev->rgmii_dev)
+ rgmii_set_speed(dev->rgmii_dev, dev->rgmii_input,
+ dev->phy.speed);
+ else
+ zmii_set_speed(dev->zmii_dev, dev->zmii_input, dev->phy.speed);
- if ((stacr & EMAC_STACR_OC) == 0) {
- printk(KERN_WARNING "%s: PHY read timeout #1!\n", dev->name);
- return -1;
+#if !defined(CONFIG_40x)
+ /* on 40x erratum forces us to NOT use integrated flow control,
+ * let's hope it works on 44x ;)
+ */
+ if (dev->phy.duplex == DUPLEX_FULL) {
+ if (dev->phy.pause)
+ r |= EMAC_MR1_EIFC | EMAC_MR1_APP;
+ else if (dev->phy.asym_pause)
+ r |= EMAC_MR1_APP;
}
+#endif
+ out_be32(&p->mr1, r);
+
+ /* Set individual MAC address */
+ out_be32(&p->iahr, (ndev->dev_addr[0] << 8) | ndev->dev_addr[1]);
+ out_be32(&p->ialr, (ndev->dev_addr[2] << 24) |
+ (ndev->dev_addr[3] << 16) | (ndev->dev_addr[4] << 8) |
+ ndev->dev_addr[5]);
+
+ /* VLAN Tag Protocol ID */
+ out_be32(&p->vtpid, 0x8100);
+
+ /* Receive mode register */
+ r = emac_iff2rmr(ndev);
+ if (r & EMAC_RMR_MAE)
+ emac_hash_mc(dev);
+ out_be32(&p->rmr, r);
+
+ /* FIFOs thresholds */
+ r = EMAC_TMR1((EMAC_MAL_BURST_SIZE / EMAC_FIFO_ENTRY_SIZE) + 1,
+ EMAC_TX_FIFO_SIZE / 2 / EMAC_FIFO_ENTRY_SIZE);
+ out_be32(&p->tmr1, r);
+ out_be32(&p->trtr, EMAC_TRTR(EMAC_TX_FIFO_SIZE / 2));
+
+ /* PAUSE frame is sent when RX FIFO reaches its high-water mark,
+ there should be still enough space in FIFO to allow the our link
+ partner time to process this frame and also time to send PAUSE
+ frame itself.
+
+ Here is the worst case scenario for the RX FIFO "headroom"
+ (from "The Switch Book") (100Mbps, without preamble, inter-frame gap):
+
+ 1) One maximum-length frame on TX 1522 bytes
+ 2) One PAUSE frame time 64 bytes
+ 3) PAUSE frame decode time allowance 64 bytes
+ 4) One maximum-length frame on RX 1522 bytes
+ 5) Round-trip propagation delay of the link (100Mb) 15 bytes
+ ----------
+ 3187 bytes
+
+ I chose to set high-water mark to RX_FIFO_SIZE / 4 (1024 bytes)
+ low-water mark to RX_FIFO_SIZE / 8 (512 bytes)
+ */
+ r = EMAC_RWMR(EMAC_RX_FIFO_SIZE(gige) / 8 / EMAC_FIFO_ENTRY_SIZE,
+ EMAC_RX_FIFO_SIZE(gige) / 4 / EMAC_FIFO_ENTRY_SIZE);
+ out_be32(&p->rwmr, r);
+
+ /* Set PAUSE timer to the maximum */
+ out_be32(&p->ptr, 0xffff);
+
+ /* IRQ sources */
+ out_be32(&p->iser, EMAC_ISR_TXPE | EMAC_ISR_RXPE | /* EMAC_ISR_TXUE |
+ EMAC_ISR_RXOE | */ EMAC_ISR_OVR | EMAC_ISR_BP | EMAC_ISR_SE |
+ EMAC_ISR_ALE | EMAC_ISR_BFCS | EMAC_ISR_PTLE | EMAC_ISR_ORE |
+ EMAC_ISR_IRE | EMAC_ISR_TE);
+
+ /* We need to take GPCS PHY out of isolate mode after EMAC reset */
+ if (emac_phy_gpcs(dev->phy.mode))
+ mii_reset_phy(&dev->phy);
+
+ return 0;
+}
- /* Clear the speed bits and make a read request to the PHY */
- stacr = ((EMAC_STACR_READ | (reg & 0x1f)) & ~EMAC_STACR_CLK_100MHZ);
- stacr |= ((mii_id & 0x1F) << 5);
+/* BHs disabled */
+static void emac_reinitialize(struct ocp_enet_private *dev)
+{
+ DBG("%d: reinitialize" NL, dev->def->index);
- out_be32(&emacp->em0stacr, stacr);
+ if (!emac_configure(dev)) {
+ emac_tx_enable(dev);
+ emac_rx_enable(dev);
+ }
+}
- count = 0;
- while ((((stacr = in_be32(&emacp->em0stacr)) & EMAC_STACR_OC) == 0)
- && (count++ < MDIO_DELAY))
- udelay(1);
- MDIO_DEBUG((" (count was %d)\n", count));
+/* BHs disabled */
+static void emac_full_tx_reset(struct net_device *ndev)
+{
+ struct ocp_enet_private *dev = ndev->priv;
+ struct ocp_func_emac_data *emacdata = dev->def->additions;
- if ((stacr & EMAC_STACR_OC) == 0) {
- printk(KERN_WARNING "%s: PHY read timeout #2!\n", dev->name);
- return -1;
- }
+ DBG("%d: full_tx_reset" NL, dev->def->index);
- /* Check for a read error */
- if (stacr & EMAC_STACR_PHYE) {
- MDIO_DEBUG(("EMAC MDIO PHY error !\n"));
- return -1;
- }
+ emac_tx_disable(dev);
+ mal_disable_tx_channel(dev->mal, emacdata->mal_tx_chan);
+ emac_clean_tx_ring(dev);
+ dev->tx_cnt = dev->tx_slot = dev->ack_slot = 0;
+
+ emac_configure(dev);
- MDIO_DEBUG((" -> 0x%x\n", stacr >> 16));
+ mal_enable_tx_channel(dev->mal, emacdata->mal_tx_chan);
+ emac_tx_enable(dev);
+ emac_rx_enable(dev);
- return (stacr >> 16);
+ netif_wake_queue(ndev);
}
-void emac_phy_write(struct net_device *dev, int mii_id, int reg, int data)
+static int __emac_mdio_read(struct ocp_enet_private *dev, u8 id, u8 reg)
{
- int count;
- uint32_t stacr;
- struct ocp_enet_private *fep = dev->priv;
- emac_t *emacp = fep->emacp;
+ struct emac_regs *p = dev->emacp;
+ u32 r;
+ int n;
- MDIO_DEBUG(("%s phy_write, id: 0x%x, reg: 0x%x, data: 0x%x\n",
- dev->name, mii_id, reg, data));
+ DBG2("%d: mdio_read(%02x,%02x)" NL, dev->def->index, id, reg);
- /* Enable proper ZMII port */
- if (fep->zmii_dev)
- emac_enable_zmii_port(fep->zmii_dev, fep->zmii_input);
+ /* Enable proper MDIO port */
+ zmii_enable_mdio(dev->zmii_dev, dev->zmii_input);
- /* Use the EMAC that has the MDIO port */
- if (fep->mdio_dev) {
- dev = fep->mdio_dev;
- fep = dev->priv;
- emacp = fep->emacp;
+ /* Wait for management interface to become idle */
+ n = 10;
+ while (!(in_be32(&p->stacr) & EMAC_STACR_OC)) {
+ udelay(1);
+ if (!--n)
+ goto to;
}
- count = 0;
- while ((((stacr = in_be32(&emacp->em0stacr)) & EMAC_STACR_OC) == 0)
- && (count++ < MDIO_DELAY))
+ /* Issue read command */
+ out_be32(&p->stacr,
+ EMAC_STACR_BASE(emac_opb_mhz()) | EMAC_STACR_STAC_READ |
+ (reg & EMAC_STACR_PRA_MASK)
+ | ((id & EMAC_STACR_PCDA_MASK) << EMAC_STACR_PCDA_SHIFT));
+
+ /* Wait for read to complete */
+ n = 100;
+ while (!((r = in_be32(&p->stacr)) & EMAC_STACR_OC)) {
udelay(1);
- MDIO_DEBUG((" (count was %d)\n", count));
+ if (!--n)
+ goto to;
+ }
- if ((stacr & EMAC_STACR_OC) == 0) {
- printk(KERN_WARNING "%s: PHY write timeout #2!\n", dev->name);
- return;
+ if (unlikely(r & EMAC_STACR_PHYE)) {
+ DBG("%d: mdio_read(%02x, %02x) failed" NL, dev->def->index,
+ id, reg);
+ return -EREMOTEIO;
}
- /* Clear the speed bits and make a read request to the PHY */
+ r = ((r >> EMAC_STACR_PHYD_SHIFT) & EMAC_STACR_PHYD_MASK);
+ DBG2("%d: mdio_read -> %04x" NL, dev->def->index, r);
+ return r;
+ to:
+ DBG("%d: MII management interface timeout (read)" NL, dev->def->index);
+ return -ETIMEDOUT;
+}
+
+static void __emac_mdio_write(struct ocp_enet_private *dev, u8 id, u8 reg,
+ u16 val)
+{
+ struct emac_regs *p = dev->emacp;
+ int n;
- stacr = ((EMAC_STACR_WRITE | (reg & 0x1f)) & ~EMAC_STACR_CLK_100MHZ);
- stacr |= ((mii_id & 0x1f) << 5) | ((data & 0xffff) << 16);
+ DBG2("%d: mdio_write(%02x,%02x,%04x)" NL, dev->def->index, id, reg,
+ val);
- out_be32(&emacp->em0stacr, stacr);
+ /* Enable proper MDIO port */
+ zmii_enable_mdio(dev->zmii_dev, dev->zmii_input);
- count = 0;
- while ((((stacr = in_be32(&emacp->em0stacr)) & EMAC_STACR_OC) == 0)
- && (count++ < MDIO_DELAY))
+ /* Wait for management interface to be idle */
+ n = 10;
+ while (!(in_be32(&p->stacr) & EMAC_STACR_OC)) {
udelay(1);
- MDIO_DEBUG((" (count was %d)\n", count));
+ if (!--n)
+ goto to;
+ }
- if ((stacr & EMAC_STACR_OC) == 0)
- printk(KERN_WARNING "%s: PHY write timeout #2!\n", dev->name);
+ /* Issue write command */
+ out_be32(&p->stacr,
+ EMAC_STACR_BASE(emac_opb_mhz()) | EMAC_STACR_STAC_WRITE |
+ (reg & EMAC_STACR_PRA_MASK) |
+ ((id & EMAC_STACR_PCDA_MASK) << EMAC_STACR_PCDA_SHIFT) |
+ (val << EMAC_STACR_PHYD_SHIFT));
- /* Check for a write error */
- if ((stacr & EMAC_STACR_PHYE) != 0) {
- MDIO_DEBUG(("EMAC MDIO PHY error !\n"));
+ /* Wait for write to complete */
+ n = 100;
+ while (!(in_be32(&p->stacr) & EMAC_STACR_OC)) {
+ udelay(1);
+ if (!--n)
+ goto to;
}
+ return;
+ to:
+ DBG("%d: MII management interface timeout (write)" NL, dev->def->index);
}
-static void emac_txeob_dev(void *param, u32 chanmask)
+static int emac_mdio_read(struct net_device *ndev, int id, int reg)
{
- struct net_device *dev = param;
- struct ocp_enet_private *fep = dev->priv;
- unsigned long flags;
-
- spin_lock_irqsave(&fep->lock, flags);
-
- PKT_DEBUG(("emac_txeob_dev() entry, tx_cnt: %d\n", fep->tx_cnt));
-
- while (fep->tx_cnt &&
- !(fep->tx_desc[fep->ack_slot].ctrl & MAL_TX_CTRL_READY)) {
+ struct ocp_enet_private *dev = ndev->priv;
+ int res;
+
+ local_bh_disable();
+ res = __emac_mdio_read(dev->mdio_dev ? dev->mdio_dev : dev, (u8) id,
+ (u8) reg);
+ local_bh_enable();
+ return res;
+}
- if (fep->tx_desc[fep->ack_slot].ctrl & MAL_TX_CTRL_LAST) {
- /* Tell the system the transmit completed. */
- dma_unmap_single(&fep->ocpdev->dev,
- fep->tx_desc[fep->ack_slot].data_ptr,
- fep->tx_desc[fep->ack_slot].data_len,
- DMA_TO_DEVICE);
- dev_kfree_skb_irq(fep->tx_skb[fep->ack_slot]);
+static void emac_mdio_write(struct net_device *ndev, int id, int reg, int val)
+{
+ struct ocp_enet_private *dev = ndev->priv;
- if (fep->tx_desc[fep->ack_slot].ctrl &
- (EMAC_TX_ST_EC | EMAC_TX_ST_MC | EMAC_TX_ST_SC))
- fep->stats.collisions++;
- }
+ local_bh_disable();
+ __emac_mdio_write(dev->mdio_dev ? dev->mdio_dev : dev, (u8) id,
+ (u8) reg, (u16) val);
+ local_bh_enable();
+}
- fep->tx_skb[fep->ack_slot] = (struct sk_buff *)NULL;
- if (++fep->ack_slot == NUM_TX_BUFF)
- fep->ack_slot = 0;
+/* BHs disabled */
+static void emac_set_multicast_list(struct net_device *ndev)
+{
+ struct ocp_enet_private *dev = ndev->priv;
+ struct emac_regs *p = dev->emacp;
+ u32 rmr = emac_iff2rmr(ndev);
+
+ DBG("%d: multicast %08x" NL, dev->def->index, rmr);
+ BUG_ON(!netif_running(dev->ndev));
+
+ /* I decided to relax register access rules here to avoid
+ * full EMAC reset.
+ *
+ * There is a real problem with EMAC4 core if we use MWSW_001 bit
+ * in MR1 register and do a full EMAC reset.
+ * One TX BD status update is delayed and, after EMAC reset, it
+ * never happens, resulting in TX hung (it'll be recovered by TX
+ * timeout handler eventually, but this is just gross).
+ * So we either have to do full TX reset or try to cheat here :)
+ *
+ * The only required change is to RX mode register, so I *think* all
+ * we need is just to stop RX channel. This seems to work on all
+ * tested SoCs. --ebs
+ */
+ emac_rx_disable(dev);
+ if (rmr & EMAC_RMR_MAE)
+ emac_hash_mc(dev);
+ out_be32(&p->rmr, rmr);
+ emac_rx_enable(dev);
+}
- fep->tx_cnt--;
+/* BHs disabled */
+static int emac_resize_rx_ring(struct ocp_enet_private *dev, int new_mtu)
+{
+ struct ocp_func_emac_data *emacdata = dev->def->additions;
+ int rx_sync_size = emac_rx_sync_size(new_mtu);
+ int rx_skb_size = emac_rx_skb_size(new_mtu);
+ int i, ret = 0;
+
+ emac_rx_disable(dev);
+ mal_disable_rx_channel(dev->mal, emacdata->mal_rx_chan);
+
+ if (dev->rx_sg_skb) {
+ ++dev->estats.rx_dropped_resize;
+ dev_kfree_skb(dev->rx_sg_skb);
+ dev->rx_sg_skb = NULL;
}
- if (fep->tx_cnt < NUM_TX_BUFF)
- netif_wake_queue(dev);
- PKT_DEBUG(("emac_txeob_dev() exit, tx_cnt: %d\n", fep->tx_cnt));
+ /* Make a first pass over RX ring and mark BDs ready, dropping
+ * non-processed packets on the way. We need this as a separate pass
+ * to simplify error recovery in the case of allocation failure later.
+ */
+ for (i = 0; i < NUM_RX_BUFF; ++i) {
+ if (dev->rx_desc[i].ctrl & MAL_RX_CTRL_FIRST)
+ ++dev->estats.rx_dropped_resize;
- spin_unlock_irqrestore(&fep->lock, flags);
-}
+ dev->rx_desc[i].data_len = 0;
+ dev->rx_desc[i].ctrl = MAL_RX_CTRL_EMPTY |
+ (i == (NUM_RX_BUFF - 1) ? MAL_RX_CTRL_WRAP : 0);
+ }
-/*
- Fill/Re-fill the rx chain with valid ctrl/ptrs.
- This function will fill from rx_slot up to the parm end.
- So to completely fill the chain pre-set rx_slot to 0 and
- pass in an end of 0.
- */
-static void emac_rx_fill(struct net_device *dev, int end)
-{
- int i;
- struct ocp_enet_private *fep = dev->priv;
-
- i = fep->rx_slot;
- do {
- /* We don't want the 16 bytes skb_reserve done by dev_alloc_skb,
- * it breaks our cache line alignement. However, we still allocate
- * +16 so that we end up allocating the exact same size as
- * dev_alloc_skb() would do.
- * Also, because of the skb_res, the max DMA size we give to EMAC
- * is slighly wrong, causing it to potentially DMA 2 more bytes
- * from a broken/oversized packet. These 16 bytes will take care
- * that we don't walk on somebody else toes with that.
- */
- fep->rx_skb[i] =
- alloc_skb(fep->rx_buffer_size + 16, GFP_ATOMIC);
-
- if (fep->rx_skb[i] == NULL) {
- /* Keep rx_slot here, the next time clean/fill is called
- * we will try again before the MAL wraps back here
- * If the MAL tries to use this descriptor with
- * the EMPTY bit off it will cause the
- * rxde interrupt. That is where we will
- * try again to allocate an sk_buff.
- */
- break;
+ /* Reallocate RX ring only if bigger skb buffers are required */
+ if (rx_skb_size <= dev->rx_skb_size)
+ goto skip;
+ /* Second pass, allocate new skbs */
+ for (i = 0; i < NUM_RX_BUFF; ++i) {
+ struct sk_buff *skb = alloc_skb(rx_skb_size, GFP_ATOMIC);
+ if (!skb) {
+ ret = -ENOMEM;
+ goto oom;
}
- if (skb_res)
- skb_reserve(fep->rx_skb[i], skb_res);
+ BUG_ON(!dev->rx_skb[i]);
+ dev_kfree_skb(dev->rx_skb[i]);
- /* We must NOT dma_map_single the cache line right after the
- * buffer, so we must crop our sync size to account for the
- * reserved space
- */
- fep->rx_desc[i].data_ptr =
- (unsigned char *)dma_map_single(&fep->ocpdev->dev,
- (void *)fep->rx_skb[i]->
- data,
- fep->rx_buffer_size -
- skb_res, DMA_FROM_DEVICE);
-
- /*
- * Some 4xx implementations use the previously
- * reserved bits in data_len to encode the MS
- * 4-bits of a 36-bit physical address (ERPN)
- * This must be initialized.
- */
- fep->rx_desc[i].data_len = 0;
- fep->rx_desc[i].ctrl = MAL_RX_CTRL_EMPTY | MAL_RX_CTRL_INTR |
- (i == (NUM_RX_BUFF - 1) ? MAL_RX_CTRL_WRAP : 0);
+ skb_reserve(skb, EMAC_RX_SKB_HEADROOM + 2);
+ dev->rx_desc[i].data_ptr =
+ dma_map_single(dev->ldev, skb->data - 2, rx_sync_size,
+ DMA_FROM_DEVICE) + 2;
+ dev->rx_skb[i] = skb;
+ }
+ skip:
+ /* Check if we need to change "Jumbo" bit in MR1 */
+ if ((new_mtu > ETH_DATA_LEN) ^ (dev->ndev->mtu > ETH_DATA_LEN)) {
+ /* This is to prevent starting RX channel in emac_rx_enable() */
+ dev->commac.rx_stopped = 1;
+
+ dev->ndev->mtu = new_mtu;
+ emac_full_tx_reset(dev->ndev);
+ }
- } while ((i = (i + 1) % NUM_RX_BUFF) != end);
+ mal_set_rcbs(dev->mal, emacdata->mal_rx_chan, emac_rx_size(new_mtu));
+ oom:
+ /* Restart RX */
+ dev->commac.rx_stopped = dev->rx_slot = 0;
+ mal_enable_rx_channel(dev->mal, emacdata->mal_rx_chan);
+ emac_rx_enable(dev);
- fep->rx_slot = i;
+ return ret;
}
-static void
-emac_rx_csum(struct net_device *dev, unsigned short ctrl, struct sk_buff *skb)
+/* Process ctx, rtnl_lock semaphore */
+static int emac_change_mtu(struct net_device *ndev, int new_mtu)
{
- struct ocp_enet_private *fep = dev->priv;
+ struct ocp_enet_private *dev = ndev->priv;
+ int ret = 0;
- /* Exit if interface has no TAH engine */
- if (!fep->tah_dev) {
- skb->ip_summed = CHECKSUM_NONE;
- return;
- }
+ if (new_mtu < EMAC_MIN_MTU || new_mtu > EMAC_MAX_MTU)
+ return -EINVAL;
- /* Check for TCP/UDP/IP csum error */
- if (ctrl & EMAC_CSUM_VER_ERROR) {
- /* Let the stack verify checksum errors */
- skb->ip_summed = CHECKSUM_NONE;
-/* adapter->hw_csum_err++; */
- } else {
- /* Csum is good */
- skb->ip_summed = CHECKSUM_UNNECESSARY;
-/* adapter->hw_csum_good++; */
- }
-}
+ DBG("%d: change_mtu(%d)" NL, dev->def->index, new_mtu);
-static int emac_rx_clean(struct net_device *dev)
-{
- int i, b, bnum = 0, buf[6];
- int error, frame_length;
- struct ocp_enet_private *fep = dev->priv;
- unsigned short ctrl;
+ local_bh_disable();
+ if (netif_running(ndev)) {
+ /* Check if we really need to reinitalize RX ring */
+ if (emac_rx_skb_size(ndev->mtu) != emac_rx_skb_size(new_mtu))
+ ret = emac_resize_rx_ring(dev, new_mtu);
+ }
- i = fep->rx_slot;
+ if (!ret) {
+ ndev->mtu = new_mtu;
+ dev->rx_skb_size = emac_rx_skb_size(new_mtu);
+ dev->rx_sync_size = emac_rx_sync_size(new_mtu);
+ }
+ local_bh_enable();
- PKT_DEBUG(("emac_rx_clean() entry, rx_slot: %d\n", fep->rx_slot));
+ return ret;
+}
- do {
- if (fep->rx_skb[i] == NULL)
- continue; /*we have already handled the packet but haved failed to alloc */
- /*
- since rx_desc is in uncached mem we don't keep reading it directly
- we pull out a local copy of ctrl and do the checks on the copy.
- */
- ctrl = fep->rx_desc[i].ctrl;
- if (ctrl & MAL_RX_CTRL_EMPTY)
- break; /*we don't have any more ready packets */
-
- if (EMAC_IS_BAD_RX_PACKET(ctrl)) {
- fep->stats.rx_errors++;
- fep->stats.rx_dropped++;
-
- if (ctrl & EMAC_RX_ST_OE)
- fep->stats.rx_fifo_errors++;
- if (ctrl & EMAC_RX_ST_AE)
- fep->stats.rx_frame_errors++;
- if (ctrl & EMAC_RX_ST_BFCS)
- fep->stats.rx_crc_errors++;
- if (ctrl & (EMAC_RX_ST_RP | EMAC_RX_ST_PTL |
- EMAC_RX_ST_ORE | EMAC_RX_ST_IRE))
- fep->stats.rx_length_errors++;
- } else {
- if ((ctrl & (MAL_RX_CTRL_FIRST | MAL_RX_CTRL_LAST)) ==
- (MAL_RX_CTRL_FIRST | MAL_RX_CTRL_LAST)) {
- /* Single descriptor packet */
- emac_rx_csum(dev, ctrl, fep->rx_skb[i]);
- /* Send the skb up the chain. */
- frame_length = fep->rx_desc[i].data_len - 4;
- skb_put(fep->rx_skb[i], frame_length);
- fep->rx_skb[i]->dev = dev;
- fep->rx_skb[i]->protocol =
- eth_type_trans(fep->rx_skb[i], dev);
- error = netif_rx(fep->rx_skb[i]);
-
- if ((error == NET_RX_DROP) ||
- (error == NET_RX_BAD)) {
- fep->stats.rx_dropped++;
- } else {
- fep->stats.rx_packets++;
- fep->stats.rx_bytes += frame_length;
- }
- fep->rx_skb[i] = NULL;
- } else {
- /* Multiple descriptor packet */
- if (ctrl & MAL_RX_CTRL_FIRST) {
- if (fep->rx_desc[(i + 1) % NUM_RX_BUFF].
- ctrl & MAL_RX_CTRL_EMPTY)
- break;
- bnum = 0;
- buf[bnum] = i;
- ++bnum;
- continue;
- }
- if (((ctrl & MAL_RX_CTRL_FIRST) !=
- MAL_RX_CTRL_FIRST) &&
- ((ctrl & MAL_RX_CTRL_LAST) !=
- MAL_RX_CTRL_LAST)) {
- if (fep->rx_desc[(i + 1) %
- NUM_RX_BUFF].ctrl &
- MAL_RX_CTRL_EMPTY) {
- i = buf[0];
- break;
- }
- buf[bnum] = i;
- ++bnum;
- continue;
- }
- if (ctrl & MAL_RX_CTRL_LAST) {
- buf[bnum] = i;
- ++bnum;
- skb_put(fep->rx_skb[buf[0]],
- fep->rx_desc[buf[0]].data_len);
- for (b = 1; b < bnum; b++) {
- /*
- * MAL is braindead, we need
- * to copy the remainder
- * of the packet from the
- * latter descriptor buffers
- * to the first skb. Then
- * dispose of the source
- * skbs.
- *
- * Once the stack is fixed
- * to handle frags on most
- * protocols we can generate
- * a fragmented skb with
- * no copies.
- */
- memcpy(fep->rx_skb[buf[0]]->
- data +
- fep->rx_skb[buf[0]]->len,
- fep->rx_skb[buf[b]]->
- data,
- fep->rx_desc[buf[b]].
- data_len);
- skb_put(fep->rx_skb[buf[0]],
- fep->rx_desc[buf[b]].
- data_len);
- dma_unmap_single(&fep->ocpdev->
- dev,
- fep->
- rx_desc[buf
- [b]].
- data_ptr,
- fep->
- rx_desc[buf
- [b]].
- data_len,
- DMA_FROM_DEVICE);
- dev_kfree_skb(fep->
- rx_skb[buf[b]]);
- }
- emac_rx_csum(dev, ctrl,
- fep->rx_skb[buf[0]]);
-
- fep->rx_skb[buf[0]]->dev = dev;
- fep->rx_skb[buf[0]]->protocol =
- eth_type_trans(fep->rx_skb[buf[0]],
- dev);
- error = netif_rx(fep->rx_skb[buf[0]]);
-
- if ((error == NET_RX_DROP)
- || (error == NET_RX_BAD)) {
- fep->stats.rx_dropped++;
- } else {
- fep->stats.rx_packets++;
- fep->stats.rx_bytes +=
- fep->rx_skb[buf[0]]->len;
- }
- for (b = 0; b < bnum; b++)
- fep->rx_skb[buf[b]] = NULL;
- }
- }
+static void emac_clean_tx_ring(struct ocp_enet_private *dev)
+{
+ int i;
+ for (i = 0; i < NUM_TX_BUFF; ++i) {
+ if (dev->tx_skb[i]) {
+ dev_kfree_skb(dev->tx_skb[i]);
+ dev->tx_skb[i] = NULL;
+ if (dev->tx_desc[i].ctrl & MAL_TX_CTRL_READY)
+ ++dev->estats.tx_dropped;
}
- } while ((i = (i + 1) % NUM_RX_BUFF) != fep->rx_slot);
-
- PKT_DEBUG(("emac_rx_clean() exit, rx_slot: %d\n", fep->rx_slot));
-
- return i;
+ dev->tx_desc[i].ctrl = 0;
+ dev->tx_desc[i].data_ptr = 0;
+ }
}
-static void emac_rxeob_dev(void *param, u32 chanmask)
+static void emac_clean_rx_ring(struct ocp_enet_private *dev)
{
- struct net_device *dev = param;
- struct ocp_enet_private *fep = dev->priv;
- unsigned long flags;
- int n;
+ int i;
+ for (i = 0; i < NUM_RX_BUFF; ++i)
+ if (dev->rx_skb[i]) {
+ dev->rx_desc[i].ctrl = 0;
+ dev_kfree_skb(dev->rx_skb[i]);
+ dev->rx_skb[i] = NULL;
+ dev->rx_desc[i].data_ptr = 0;
+ }
- spin_lock_irqsave(&fep->lock, flags);
- if ((n = emac_rx_clean(dev)) != fep->rx_slot)
- emac_rx_fill(dev, n);
- spin_unlock_irqrestore(&fep->lock, flags);
+ if (dev->rx_sg_skb) {
+ dev_kfree_skb(dev->rx_sg_skb);
+ dev->rx_sg_skb = NULL;
+ }
}
-/*
- * This interrupt should never occurr, we don't program
- * the MAL for contiunous mode.
- */
-static void emac_txde_dev(void *param, u32 chanmask)
+static inline int emac_alloc_rx_skb(struct ocp_enet_private *dev, int slot,
+ int flags)
{
- struct net_device *dev = param;
- struct ocp_enet_private *fep = dev->priv;
+ struct sk_buff *skb = alloc_skb(dev->rx_skb_size, flags);
+ if (unlikely(!skb))
+ return -ENOMEM;
- printk(KERN_WARNING "%s: transmit descriptor error\n", dev->name);
+ dev->rx_skb[slot] = skb;
+ dev->rx_desc[slot].data_len = 0;
- emac_mac_dump(dev);
- emac_mal_dump(dev);
+ skb_reserve(skb, EMAC_RX_SKB_HEADROOM + 2);
+ dev->rx_desc[slot].data_ptr =
+ dma_map_single(dev->ldev, skb->data - 2, dev->rx_sync_size,
+ DMA_FROM_DEVICE) + 2;
+ barrier();
+ dev->rx_desc[slot].ctrl = MAL_RX_CTRL_EMPTY |
+ (slot == (NUM_RX_BUFF - 1) ? MAL_RX_CTRL_WRAP : 0);
- /* Reenable the transmit channel */
- mal_enable_tx_channels(fep->mal, fep->commac.tx_chan_mask);
+ return 0;
}
-/*
- * This interrupt should be very rare at best. This occurs when
- * the hardware has a problem with the receive descriptors. The manual
- * states that it occurs when the hardware cannot the receive descriptor
- * empty bit is not set. The recovery mechanism will be to
- * traverse through the descriptors, handle any that are marked to be
- * handled and reinitialize each along the way. At that point the driver
- * will be restarted.
- */
-static void emac_rxde_dev(void *param, u32 chanmask)
+static void emac_print_link_status(struct ocp_enet_private *dev)
{
- struct net_device *dev = param;
- struct ocp_enet_private *fep = dev->priv;
- unsigned long flags;
-
- if (net_ratelimit()) {
- printk(KERN_WARNING "%s: receive descriptor error\n",
- fep->ndev->name);
+ if (netif_carrier_ok(dev->ndev))
+ printk(KERN_INFO "%s: link is up, %d %s%s\n",
+ dev->ndev->name, dev->phy.speed,
+ dev->phy.duplex == DUPLEX_FULL ? "FDX" : "HDX",
+ dev->phy.pause ? ", pause enabled" :
+ dev->phy.asym_pause ? ", assymetric pause enabled" : "");
+ else
+ printk(KERN_INFO "%s: link is down\n", dev->ndev->name);
+}
- emac_mac_dump(dev);
- emac_mal_dump(dev);
- emac_desc_dump(dev);
+/* Process ctx, rtnl_lock semaphore */
+static int emac_open(struct net_device *ndev)
+{
+ struct ocp_enet_private *dev = ndev->priv;
+ struct ocp_func_emac_data *emacdata = dev->def->additions;
+ int err, i;
+
+ DBG("%d: open" NL, dev->def->index);
+
+ /* Setup error IRQ handler */
+ err = request_irq(dev->def->irq, emac_irq, 0, "EMAC", dev);
+ if (err) {
+ printk(KERN_ERR "%s: failed to request IRQ %d\n",
+ ndev->name, dev->def->irq);
+ return err;
}
- /* Disable RX channel */
- spin_lock_irqsave(&fep->lock, flags);
- mal_disable_rx_channels(fep->mal, fep->commac.rx_chan_mask);
-
- /* For now, charge the error against all emacs */
- fep->stats.rx_errors++;
-
- /* so do we have any good packets still? */
- emac_rx_clean(dev);
-
- /* When the interface is restarted it resets processing to the
- * first descriptor in the table.
- */
-
- fep->rx_slot = 0;
- emac_rx_fill(dev, 0);
+ /* Allocate RX ring */
+ for (i = 0; i < NUM_RX_BUFF; ++i)
+ if (emac_alloc_rx_skb(dev, i, GFP_KERNEL)) {
+ printk(KERN_ERR "%s: failed to allocate RX ring\n",
+ ndev->name);
+ goto oom;
+ }
- set_mal_dcrn(fep->mal, DCRN_MALRXEOBISR, fep->commac.rx_chan_mask);
- set_mal_dcrn(fep->mal, DCRN_MALRXDEIR, fep->commac.rx_chan_mask);
+ local_bh_disable();
+ dev->tx_cnt = dev->tx_slot = dev->ack_slot = dev->rx_slot =
+ dev->commac.rx_stopped = 0;
+ dev->rx_sg_skb = NULL;
+
+ if (dev->phy.address >= 0) {
+ int link_poll_interval;
+ if (dev->phy.def->ops->poll_link(&dev->phy)) {
+ dev->phy.def->ops->read_link(&dev->phy);
+ EMAC_RX_CLK_DEFAULT(dev->def->index);
+ netif_carrier_on(dev->ndev);
+ link_poll_interval = PHY_POLL_LINK_ON;
+ } else {
+ EMAC_RX_CLK_TX(dev->def->index);
+ netif_carrier_off(dev->ndev);
+ link_poll_interval = PHY_POLL_LINK_OFF;
+ }
+ mod_timer(&dev->link_timer, jiffies + link_poll_interval);
+ emac_print_link_status(dev);
+ } else
+ netif_carrier_on(dev->ndev);
+
+ emac_configure(dev);
+ mal_poll_add(dev->mal, &dev->commac);
+ mal_enable_tx_channel(dev->mal, emacdata->mal_tx_chan);
+ mal_set_rcbs(dev->mal, emacdata->mal_rx_chan, emac_rx_size(ndev->mtu));
+ mal_enable_rx_channel(dev->mal, emacdata->mal_rx_chan);
+ emac_tx_enable(dev);
+ emac_rx_enable(dev);
+ netif_start_queue(ndev);
+ local_bh_enable();
- /* Reenable the receive channels */
- mal_enable_rx_channels(fep->mal, fep->commac.rx_chan_mask);
- spin_unlock_irqrestore(&fep->lock, flags);
+ return 0;
+ oom:
+ emac_clean_rx_ring(dev);
+ free_irq(dev->def->irq, dev);
+ return -ENOMEM;
}
-static irqreturn_t
-emac_mac_irq(int irq, void *dev_instance, struct pt_regs *regs)
+/* BHs disabled */
+static int emac_link_differs(struct ocp_enet_private *dev)
{
- struct net_device *dev = dev_instance;
- struct ocp_enet_private *fep = dev->priv;
- emac_t *emacp = fep->emacp;
- unsigned long tmp_em0isr;
+ u32 r = in_be32(&dev->emacp->mr1);
- /* EMAC interrupt */
- tmp_em0isr = in_be32(&emacp->em0isr);
- if (tmp_em0isr & (EMAC_ISR_TE0 | EMAC_ISR_TE1)) {
- /* This error is a hard transmit error - could retransmit */
- fep->stats.tx_errors++;
+ int duplex = r & EMAC_MR1_FDE ? DUPLEX_FULL : DUPLEX_HALF;
+ int speed, pause, asym_pause;
- /* Reenable the transmit channel */
- mal_enable_tx_channels(fep->mal, fep->commac.tx_chan_mask);
+ if (r & (EMAC_MR1_MF_1000 | EMAC_MR1_MF_1000GPCS))
+ speed = SPEED_1000;
+ else if (r & EMAC_MR1_MF_100)
+ speed = SPEED_100;
+ else
+ speed = SPEED_10;
- } else {
- fep->stats.rx_errors++;
+ switch (r & (EMAC_MR1_EIFC | EMAC_MR1_APP)) {
+ case (EMAC_MR1_EIFC | EMAC_MR1_APP):
+ pause = 1;
+ asym_pause = 0;
+ break;
+ case EMAC_MR1_APP:
+ pause = 0;
+ asym_pause = 1;
+ break;
+ default:
+ pause = asym_pause = 0;
}
-
- if (tmp_em0isr & EMAC_ISR_RP)
- fep->stats.rx_length_errors++;
- if (tmp_em0isr & EMAC_ISR_ALE)
- fep->stats.rx_frame_errors++;
- if (tmp_em0isr & EMAC_ISR_BFCS)
- fep->stats.rx_crc_errors++;
- if (tmp_em0isr & EMAC_ISR_PTLE)
- fep->stats.rx_length_errors++;
- if (tmp_em0isr & EMAC_ISR_ORE)
- fep->stats.rx_length_errors++;
- if (tmp_em0isr & EMAC_ISR_TE0)
- fep->stats.tx_aborted_errors++;
-
- emac_err_dump(dev, tmp_em0isr);
-
- out_be32(&emacp->em0isr, tmp_em0isr);
-
- return IRQ_HANDLED;
+ return speed != dev->phy.speed || duplex != dev->phy.duplex ||
+ pause != dev->phy.pause || asym_pause != dev->phy.asym_pause;
}
-static int emac_start_xmit(struct sk_buff *skb, struct net_device *dev)
+/* BHs disabled */
+static void emac_link_timer(unsigned long data)
{
- unsigned short ctrl;
- unsigned long flags;
- struct ocp_enet_private *fep = dev->priv;
- emac_t *emacp = fep->emacp;
- int len = skb->len;
- unsigned int offset = 0, size, f, tx_slot_first;
- unsigned int nr_frags = skb_shinfo(skb)->nr_frags;
-
- spin_lock_irqsave(&fep->lock, flags);
-
- len -= skb->data_len;
+ struct ocp_enet_private *dev = (struct ocp_enet_private *)data;
+ int link_poll_interval;
- if ((fep->tx_cnt + nr_frags + len / DESC_BUF_SIZE + 1) > NUM_TX_BUFF) {
- PKT_DEBUG(("emac_start_xmit() stopping queue\n"));
- netif_stop_queue(dev);
- spin_unlock_irqrestore(&fep->lock, flags);
- return -EBUSY;
- }
+ DBG2("%d: link timer" NL, dev->def->index);
- tx_slot_first = fep->tx_slot;
+ if (dev->phy.def->ops->poll_link(&dev->phy)) {
+ if (!netif_carrier_ok(dev->ndev)) {
+ EMAC_RX_CLK_DEFAULT(dev->def->index);
- while (len) {
- size = min(len, DESC_BUF_SIZE);
+ /* Get new link parameters */
+ dev->phy.def->ops->read_link(&dev->phy);
- fep->tx_desc[fep->tx_slot].data_len = (short)size;
- fep->tx_desc[fep->tx_slot].data_ptr =
- (unsigned char *)dma_map_single(&fep->ocpdev->dev,
- (void *)((unsigned int)skb->
- data + offset),
- size, DMA_TO_DEVICE);
+ if (dev->tah_dev || emac_link_differs(dev))
+ emac_full_tx_reset(dev->ndev);
- ctrl = EMAC_TX_CTRL_DFLT;
- if (fep->tx_slot != tx_slot_first)
- ctrl |= MAL_TX_CTRL_READY;
- if ((NUM_TX_BUFF - 1) == fep->tx_slot)
- ctrl |= MAL_TX_CTRL_WRAP;
- if (!nr_frags && (len == size)) {
- ctrl |= MAL_TX_CTRL_LAST;
- fep->tx_skb[fep->tx_slot] = skb;
+ netif_carrier_on(dev->ndev);
+ emac_print_link_status(dev);
+ }
+ link_poll_interval = PHY_POLL_LINK_ON;
+ } else {
+ if (netif_carrier_ok(dev->ndev)) {
+ EMAC_RX_CLK_TX(dev->def->index);
+#if defined(CONFIG_IBM_EMAC_PHY_RX_CLK_FIX)
+ emac_reinitialize(dev);
+#endif
+ netif_carrier_off(dev->ndev);
+ emac_print_link_status(dev);
}
- if (skb->ip_summed == CHECKSUM_HW)
- ctrl |= EMAC_TX_CTRL_TAH_CSUM;
-
- fep->tx_desc[fep->tx_slot].ctrl = ctrl;
-
- len -= size;
- offset += size;
- /* Bump tx count */
- if (++fep->tx_cnt == NUM_TX_BUFF)
- netif_stop_queue(dev);
+ /* Retry reset if the previous attempt failed.
+ * This is needed mostly for CONFIG_IBM_EMAC_PHY_RX_CLK_FIX
+ * case, but I left it here because it shouldn't trigger for
+ * sane PHYs anyway.
+ */
+ if (unlikely(dev->reset_failed))
+ emac_reinitialize(dev);
- /* Next descriptor */
- if (++fep->tx_slot == NUM_TX_BUFF)
- fep->tx_slot = 0;
+ link_poll_interval = PHY_POLL_LINK_OFF;
}
+ mod_timer(&dev->link_timer, jiffies + link_poll_interval);
+}
- for (f = 0; f < nr_frags; f++) {
- struct skb_frag_struct *frag;
-
- frag = &skb_shinfo(skb)->frags[f];
- len = frag->size;
- offset = 0;
-
- while (len) {
- size = min(len, DESC_BUF_SIZE);
-
- dma_map_page(&fep->ocpdev->dev,
- frag->page,
- frag->page_offset + offset,
- size, DMA_TO_DEVICE);
-
- ctrl = EMAC_TX_CTRL_DFLT | MAL_TX_CTRL_READY;
- if ((NUM_TX_BUFF - 1) == fep->tx_slot)
- ctrl |= MAL_TX_CTRL_WRAP;
- if ((f == (nr_frags - 1)) && (len == size)) {
- ctrl |= MAL_TX_CTRL_LAST;
- fep->tx_skb[fep->tx_slot] = skb;
- }
-
- if (skb->ip_summed == CHECKSUM_HW)
- ctrl |= EMAC_TX_CTRL_TAH_CSUM;
-
- fep->tx_desc[fep->tx_slot].data_len = (short)size;
- fep->tx_desc[fep->tx_slot].data_ptr =
- (char *)((page_to_pfn(frag->page) << PAGE_SHIFT) +
- frag->page_offset + offset);
- fep->tx_desc[fep->tx_slot].ctrl = ctrl;
-
- len -= size;
- offset += size;
-
- /* Bump tx count */
- if (++fep->tx_cnt == NUM_TX_BUFF)
- netif_stop_queue(dev);
+/* BHs disabled */
+static void emac_force_link_update(struct ocp_enet_private *dev)
+{
+ netif_carrier_off(dev->ndev);
+ if (timer_pending(&dev->link_timer))
+ mod_timer(&dev->link_timer, jiffies + PHY_POLL_LINK_OFF);
+}
- /* Next descriptor */
- if (++fep->tx_slot == NUM_TX_BUFF)
- fep->tx_slot = 0;
- }
- }
+/* Process ctx, rtnl_lock semaphore */
+static int emac_close(struct net_device *ndev)
+{
+ struct ocp_enet_private *dev = ndev->priv;
+ struct ocp_func_emac_data *emacdata = dev->def->additions;
- /*
- * Deferred set READY on first descriptor of packet to
- * avoid TX MAL race.
- */
- fep->tx_desc[tx_slot_first].ctrl |= MAL_TX_CTRL_READY;
+ DBG("%d: close" NL, dev->def->index);
- /* Send the packet out. */
- out_be32(&emacp->em0tmr0, EMAC_TMR0_XMIT);
+ local_bh_disable();
- fep->stats.tx_packets++;
- fep->stats.tx_bytes += skb->len;
+ if (dev->phy.address >= 0)
+ del_timer_sync(&dev->link_timer);
- PKT_DEBUG(("emac_start_xmit() exitn"));
+ netif_stop_queue(ndev);
+ emac_rx_disable(dev);
+ emac_tx_disable(dev);
+ mal_disable_rx_channel(dev->mal, emacdata->mal_rx_chan);
+ mal_disable_tx_channel(dev->mal, emacdata->mal_tx_chan);
+ mal_poll_del(dev->mal, &dev->commac);
+ local_bh_enable();
- spin_unlock_irqrestore(&fep->lock, flags);
+ emac_clean_tx_ring(dev);
+ emac_clean_rx_ring(dev);
+ free_irq(dev->def->irq, dev);
return 0;
}
-static int emac_adjust_to_link(struct ocp_enet_private *fep)
+static inline u16 emac_tx_csum(struct ocp_enet_private *dev,
+ struct sk_buff *skb)
{
- emac_t *emacp = fep->emacp;
- unsigned long mode_reg;
- int full_duplex, speed;
-
- full_duplex = 0;
- speed = SPEED_10;
-
- /* set mode register 1 defaults */
- mode_reg = EMAC_M1_DEFAULT;
-
- /* Read link mode on PHY */
- if (fep->phy_mii.def->ops->read_link(&fep->phy_mii) == 0) {
- /* If an error occurred, we don't deal with it yet */
- full_duplex = (fep->phy_mii.duplex == DUPLEX_FULL);
- speed = fep->phy_mii.speed;
+#if defined(CONFIG_IBM_EMAC_TAH)
+ if (skb->ip_summed == CHECKSUM_HW) {
+ ++dev->stats.tx_packets_csum;
+ return EMAC_TX_CTRL_TAH_CSUM;
}
+#endif
+ return 0;
+}
+static inline int emac_xmit_finish(struct ocp_enet_private *dev, int len)
+{
+ struct emac_regs *p = dev->emacp;
+ struct net_device *ndev = dev->ndev;
- /* set speed (default is 10Mb) */
- switch (speed) {
- case SPEED_1000:
- mode_reg |= EMAC_M1_RFS_16K;
- if (fep->rgmii_dev) {
- struct ibm_ocp_rgmii *rgmii = RGMII_PRIV(fep->rgmii_dev);
-
- if ((rgmii->mode[fep->rgmii_input] == RTBI)
- || (rgmii->mode[fep->rgmii_input] == TBI))
- mode_reg |= EMAC_M1_MF_1000GPCS;
- else
- mode_reg |= EMAC_M1_MF_1000MBPS;
-
- emac_rgmii_port_speed(fep->rgmii_dev, fep->rgmii_input,
- 1000);
- }
- break;
- case SPEED_100:
- mode_reg |= EMAC_M1_MF_100MBPS | EMAC_M1_RFS_4K;
- if (fep->rgmii_dev)
- emac_rgmii_port_speed(fep->rgmii_dev, fep->rgmii_input,
- 100);
- if (fep->zmii_dev)
- emac_zmii_port_speed(fep->zmii_dev, fep->zmii_input,
- 100);
- break;
- case SPEED_10:
- default:
- mode_reg = (mode_reg & ~EMAC_M1_MF_100MBPS) | EMAC_M1_RFS_4K;
- if (fep->rgmii_dev)
- emac_rgmii_port_speed(fep->rgmii_dev, fep->rgmii_input,
- 10);
- if (fep->zmii_dev)
- emac_zmii_port_speed(fep->zmii_dev, fep->zmii_input,
- 10);
- }
-
- if (full_duplex)
- mode_reg |= EMAC_M1_FDE | EMAC_M1_EIFC | EMAC_M1_IST;
- else
- mode_reg &= ~(EMAC_M1_FDE | EMAC_M1_EIFC | EMAC_M1_ILE);
+ /* Send the packet out */
+ out_be32(&p->tmr0, EMAC_TMR0_XMIT);
- LINK_DEBUG(("%s: adjust to link, speed: %d, duplex: %d, opened: %d\n",
- fep->ndev->name, speed, full_duplex, fep->opened));
+ if (unlikely(++dev->tx_cnt == NUM_TX_BUFF)) {
+ netif_stop_queue(ndev);
+ DBG2("%d: stopped TX queue" NL, dev->def->index);
+ }
- printk(KERN_INFO "%s: Speed: %d, %s duplex.\n",
- fep->ndev->name, speed, full_duplex ? "Full" : "Half");
- if (fep->opened)
- out_be32(&emacp->em0mr1, mode_reg);
+ ndev->trans_start = jiffies;
+ ++dev->stats.tx_packets;
+ dev->stats.tx_bytes += len;
return 0;
}
-static int emac_set_mac_address(struct net_device *ndev, void *p)
+/* BHs disabled */
+static int emac_start_xmit(struct sk_buff *skb, struct net_device *ndev)
{
- struct ocp_enet_private *fep = ndev->priv;
- emac_t *emacp = fep->emacp;
- struct sockaddr *addr = p;
+ struct ocp_enet_private *dev = ndev->priv;
+ unsigned int len = skb->len;
+ int slot;
- if (!is_valid_ether_addr(addr->sa_data))
- return -EADDRNOTAVAIL;
+ u16 ctrl = EMAC_TX_CTRL_GFCS | EMAC_TX_CTRL_GP | MAL_TX_CTRL_READY |
+ MAL_TX_CTRL_LAST | emac_tx_csum(dev, skb);
- memcpy(ndev->dev_addr, addr->sa_data, ndev->addr_len);
+ slot = dev->tx_slot++;
+ if (dev->tx_slot == NUM_TX_BUFF) {
+ dev->tx_slot = 0;
+ ctrl |= MAL_TX_CTRL_WRAP;
+ }
- /* set the high address */
- out_be32(&emacp->em0iahr,
- (fep->ndev->dev_addr[0] << 8) | fep->ndev->dev_addr[1]);
+ DBG2("%d: xmit(%u) %d" NL, dev->def->index, len, slot);
- /* set the low address */
- out_be32(&emacp->em0ialr,
- (fep->ndev->dev_addr[2] << 24) | (fep->ndev->dev_addr[3] << 16)
- | (fep->ndev->dev_addr[4] << 8) | fep->ndev->dev_addr[5]);
+ dev->tx_skb[slot] = skb;
+ dev->tx_desc[slot].data_ptr = dma_map_single(dev->ldev, skb->data, len,
+ DMA_TO_DEVICE);
+ dev->tx_desc[slot].data_len = (u16) len;
+ barrier();
+ dev->tx_desc[slot].ctrl = ctrl;
- return 0;
+ return emac_xmit_finish(dev, len);
}
-static int emac_change_mtu(struct net_device *dev, int new_mtu)
+#if defined(CONFIG_IBM_EMAC_TAH)
+static inline int emac_xmit_split(struct ocp_enet_private *dev, int slot,
+ u32 pd, int len, int last, u16 base_ctrl)
{
- struct ocp_enet_private *fep = dev->priv;
- int old_mtu = dev->mtu;
- unsigned long mode_reg;
- emac_t *emacp = fep->emacp;
- u32 em0mr0;
- int i, full;
- unsigned long flags;
-
- if ((new_mtu < EMAC_MIN_MTU) || (new_mtu > EMAC_MAX_MTU)) {
- printk(KERN_ERR
- "emac: Invalid MTU setting, MTU must be between %d and %d\n",
- EMAC_MIN_MTU, EMAC_MAX_MTU);
- return -EINVAL;
- }
+ while (1) {
+ u16 ctrl = base_ctrl;
+ int chunk = min(len, MAL_MAX_TX_SIZE);
+ len -= chunk;
- if (old_mtu != new_mtu && netif_running(dev)) {
- /* Stop rx engine */
- em0mr0 = in_be32(&emacp->em0mr0);
- out_be32(&emacp->em0mr0, em0mr0 & ~EMAC_M0_RXE);
-
- /* Wait for descriptors to be empty */
- do {
- full = 0;
- for (i = 0; i < NUM_RX_BUFF; i++)
- if (!(fep->rx_desc[i].ctrl & MAL_RX_CTRL_EMPTY)) {
- printk(KERN_NOTICE
- "emac: RX ring is still full\n");
- full = 1;
- }
- } while (full);
-
- spin_lock_irqsave(&fep->lock, flags);
-
- mal_disable_rx_channels(fep->mal, fep->commac.rx_chan_mask);
-
- /* Destroy all old rx skbs */
- for (i = 0; i < NUM_RX_BUFF; i++) {
- dma_unmap_single(&fep->ocpdev->dev,
- fep->rx_desc[i].data_ptr,
- fep->rx_desc[i].data_len,
- DMA_FROM_DEVICE);
- dev_kfree_skb(fep->rx_skb[i]);
- fep->rx_skb[i] = NULL;
- }
+ slot = (slot + 1) % NUM_TX_BUFF;
- /* Set new rx_buffer_size, jumbo cap, and advertise new mtu */
- mode_reg = in_be32(&emacp->em0mr1);
- if (new_mtu > ENET_DEF_MTU_SIZE) {
- mode_reg |= EMAC_M1_JUMBO_ENABLE;
- fep->rx_buffer_size = EMAC_MAX_FRAME;
- } else {
- mode_reg &= ~EMAC_M1_JUMBO_ENABLE;
- fep->rx_buffer_size = ENET_DEF_BUF_SIZE;
- }
- dev->mtu = new_mtu;
- out_be32(&emacp->em0mr1, mode_reg);
+ if (last && !len)
+ ctrl |= MAL_TX_CTRL_LAST;
+ if (slot == NUM_TX_BUFF - 1)
+ ctrl |= MAL_TX_CTRL_WRAP;
- /* Re-init rx skbs */
- fep->rx_slot = 0;
- emac_rx_fill(dev, 0);
+ dev->tx_skb[slot] = NULL;
+ dev->tx_desc[slot].data_ptr = pd;
+ dev->tx_desc[slot].data_len = (u16) chunk;
+ dev->tx_desc[slot].ctrl = ctrl;
+ ++dev->tx_cnt;
- /* Restart the rx engine */
- mal_enable_rx_channels(fep->mal, fep->commac.rx_chan_mask);
- out_be32(&emacp->em0mr0, em0mr0 | EMAC_M0_RXE);
+ if (!len)
+ break;
- spin_unlock_irqrestore(&fep->lock, flags);
+ pd += chunk;
}
-
- return 0;
+ return slot;
}
-static void __emac_set_multicast_list(struct net_device *dev)
+/* BHs disabled (SG version for TAH equipped EMACs) */
+static int emac_start_xmit_sg(struct sk_buff *skb, struct net_device *ndev)
{
- struct ocp_enet_private *fep = dev->priv;
- emac_t *emacp = fep->emacp;
- u32 rmr = in_be32(&emacp->em0rmr);
-
- /* First clear all special bits, they can be set later */
- rmr &= ~(EMAC_RMR_PME | EMAC_RMR_PMME | EMAC_RMR_MAE);
+ struct ocp_enet_private *dev = ndev->priv;
+ int nr_frags = skb_shinfo(skb)->nr_frags;
+ int len = skb->len, chunk;
+ int slot, i;
+ u16 ctrl;
+ u32 pd;
- if (dev->flags & IFF_PROMISC) {
- rmr |= EMAC_RMR_PME;
- } else if (dev->flags & IFF_ALLMULTI || 32 < dev->mc_count) {
- /*
- * Must be setting up to use multicast
- * Now check for promiscuous multicast
- */
- rmr |= EMAC_RMR_PMME;
- } else if (dev->flags & IFF_MULTICAST && 0 < dev->mc_count) {
- unsigned short em0gaht[4] = { 0, 0, 0, 0 };
- struct dev_mc_list *dmi;
-
- /* Need to hash on the multicast address. */
- for (dmi = dev->mc_list; dmi; dmi = dmi->next) {
- unsigned long mc_crc;
- unsigned int bit_number;
-
- mc_crc = ether_crc(6, (char *)dmi->dmi_addr);
- bit_number = 63 - (mc_crc >> 26); /* MSB: 0 LSB: 63 */
- em0gaht[bit_number >> 4] |=
- 0x8000 >> (bit_number & 0x0f);
- }
- emacp->em0gaht1 = em0gaht[0];
- emacp->em0gaht2 = em0gaht[1];
- emacp->em0gaht3 = em0gaht[2];
- emacp->em0gaht4 = em0gaht[3];
+ /* This is common "fast" path */
+ if (likely(!nr_frags && len <= MAL_MAX_TX_SIZE))
+ return emac_start_xmit(skb, ndev);
- /* Turn on multicast addressing */
- rmr |= EMAC_RMR_MAE;
- }
- out_be32(&emacp->em0rmr, rmr);
-}
+ len -= skb->data_len;
-static int emac_init_tah(struct ocp_enet_private *fep)
-{
- tah_t *tahp;
+ /* Note, this is only an *estimation*, we can still run out of empty
+ * slots because of the additional fragmentation into
+ * MAL_MAX_TX_SIZE-sized chunks
+ */
+ if (unlikely(dev->tx_cnt + nr_frags + mal_tx_chunks(len) > NUM_TX_BUFF))
+ goto stop_queue;
+
+ ctrl = EMAC_TX_CTRL_GFCS | EMAC_TX_CTRL_GP | MAL_TX_CTRL_READY |
+ emac_tx_csum(dev, skb);
+ slot = dev->tx_slot;
+
+ /* skb data */
+ dev->tx_skb[slot] = NULL;
+ chunk = min(len, MAL_MAX_TX_SIZE);
+ dev->tx_desc[slot].data_ptr = pd =
+ dma_map_single(dev->ldev, skb->data, len, DMA_TO_DEVICE);
+ dev->tx_desc[slot].data_len = (u16) chunk;
+ len -= chunk;
+ if (unlikely(len))
+ slot = emac_xmit_split(dev, slot, pd + chunk, len, !nr_frags,
+ ctrl);
+ /* skb fragments */
+ for (i = 0; i < nr_frags; ++i) {
+ struct skb_frag_struct *frag = &skb_shinfo(skb)->frags[i];
+ len = frag->size;
- /* Initialize TAH and enable checksum verification */
- tahp = (tah_t *) ioremap(fep->tah_dev->def->paddr, sizeof(*tahp));
+ if (unlikely(dev->tx_cnt + mal_tx_chunks(len) >= NUM_TX_BUFF))
+ goto undo_frame;
- if (tahp == NULL) {
- printk(KERN_ERR "tah%d: Cannot ioremap TAH registers!\n",
- fep->tah_dev->def->index);
+ pd = dma_map_page(dev->ldev, frag->page, frag->page_offset, len,
+ DMA_TO_DEVICE);
- return -ENOMEM;
+ slot = emac_xmit_split(dev, slot, pd, len, i == nr_frags - 1,
+ ctrl);
}
- out_be32(&tahp->tah_mr, TAH_MR_SR);
+ DBG2("%d: xmit_sg(%u) %d - %d" NL, dev->def->index, skb->len,
+ dev->tx_slot, slot);
- /* wait for reset to complete */
- while (in_be32(&tahp->tah_mr) & TAH_MR_SR) ;
+ /* Attach skb to the last slot so we don't release it too early */
+ dev->tx_skb[slot] = skb;
- /* 10KB TAH TX FIFO accomodates the max MTU of 9000 */
- out_be32(&tahp->tah_mr,
- TAH_MR_CVR | TAH_MR_ST_768 | TAH_MR_TFS_10KB | TAH_MR_DTFP |
- TAH_MR_DIG);
+ /* Send the packet out */
+ if (dev->tx_slot == NUM_TX_BUFF - 1)
+ ctrl |= MAL_TX_CTRL_WRAP;
+ barrier();
+ dev->tx_desc[dev->tx_slot].ctrl = ctrl;
+ dev->tx_slot = (slot + 1) % NUM_TX_BUFF;
- iounmap(tahp);
+ return emac_xmit_finish(dev, skb->len);
- return 0;
+ undo_frame:
+ /* Well, too bad. Our previous estimation was overly optimistic.
+ * Undo everything.
+ */
+ while (slot != dev->tx_slot) {
+ dev->tx_desc[slot].ctrl = 0;
+ --dev->tx_cnt;
+ if (--slot < 0)
+ slot = NUM_TX_BUFF - 1;
+ }
+ ++dev->estats.tx_undo;
+
+ stop_queue:
+ netif_stop_queue(ndev);
+ DBG2("%d: stopped TX queue" NL, dev->def->index);
+ return 1;
+}
+#else
+# define emac_start_xmit_sg emac_start_xmit
+#endif /* !defined(CONFIG_IBM_EMAC_TAH) */
+
+/* BHs disabled */
+static void emac_parse_tx_error(struct ocp_enet_private *dev, u16 ctrl)
+{
+ struct ibm_emac_error_stats *st = &dev->estats;
+ DBG("%d: BD TX error %04x" NL, dev->def->index, ctrl);
+
+ ++st->tx_bd_errors;
+ if (ctrl & EMAC_TX_ST_BFCS)
+ ++st->tx_bd_bad_fcs;
+ if (ctrl & EMAC_TX_ST_LCS)
+ ++st->tx_bd_carrier_loss;
+ if (ctrl & EMAC_TX_ST_ED)
+ ++st->tx_bd_excessive_deferral;
+ if (ctrl & EMAC_TX_ST_EC)
+ ++st->tx_bd_excessive_collisions;
+ if (ctrl & EMAC_TX_ST_LC)
+ ++st->tx_bd_late_collision;
+ if (ctrl & EMAC_TX_ST_MC)
+ ++st->tx_bd_multple_collisions;
+ if (ctrl & EMAC_TX_ST_SC)
+ ++st->tx_bd_single_collision;
+ if (ctrl & EMAC_TX_ST_UR)
+ ++st->tx_bd_underrun;
+ if (ctrl & EMAC_TX_ST_SQE)
+ ++st->tx_bd_sqe;
}
-static void emac_init_rings(struct net_device *dev)
+static void emac_poll_tx(void *param)
{
- struct ocp_enet_private *ep = dev->priv;
- int loop;
+ struct ocp_enet_private *dev = param;
+ DBG2("%d: poll_tx, %d %d" NL, dev->def->index, dev->tx_cnt,
+ dev->ack_slot);
+
+ if (dev->tx_cnt) {
+ u16 ctrl;
+ int slot = dev->ack_slot, n = 0;
+ again:
+ ctrl = dev->tx_desc[slot].ctrl;
+ if (!(ctrl & MAL_TX_CTRL_READY)) {
+ struct sk_buff *skb = dev->tx_skb[slot];
+ ++n;
+
+ if (skb) {
+ dev_kfree_skb(skb);
+ dev->tx_skb[slot] = NULL;
+ }
+ slot = (slot + 1) % NUM_TX_BUFF;
- ep->tx_desc = (struct mal_descriptor *)((char *)ep->mal->tx_virt_addr +
- (ep->mal_tx_chan *
- MAL_DT_ALIGN));
- ep->rx_desc =
- (struct mal_descriptor *)((char *)ep->mal->rx_virt_addr +
- (ep->mal_rx_chan * MAL_DT_ALIGN));
+ if (unlikely(EMAC_IS_BAD_TX(ctrl)))
+ emac_parse_tx_error(dev, ctrl);
- /* Fill in the transmit descriptor ring. */
- for (loop = 0; loop < NUM_TX_BUFF; loop++) {
- if (ep->tx_skb[loop]) {
- dma_unmap_single(&ep->ocpdev->dev,
- ep->tx_desc[loop].data_ptr,
- ep->tx_desc[loop].data_len,
- DMA_TO_DEVICE);
- dev_kfree_skb_irq(ep->tx_skb[loop]);
+ if (--dev->tx_cnt)
+ goto again;
}
- ep->tx_skb[loop] = NULL;
- ep->tx_desc[loop].ctrl = 0;
- ep->tx_desc[loop].data_len = 0;
- ep->tx_desc[loop].data_ptr = NULL;
- }
- ep->tx_desc[loop - 1].ctrl |= MAL_TX_CTRL_WRAP;
-
- /* Format the receive descriptor ring. */
- ep->rx_slot = 0;
- /* Default is MTU=1500 + Ethernet overhead */
- ep->rx_buffer_size = dev->mtu + ENET_HEADER_SIZE + ENET_FCS_SIZE;
- emac_rx_fill(dev, 0);
- if (ep->rx_slot != 0) {
- printk(KERN_ERR
- "%s: Not enough mem for RxChain durning Open?\n",
- dev->name);
- /*We couldn't fill the ring at startup?
- *We could clean up and fail to open but right now we will try to
- *carry on. It may be a sign of a bad NUM_RX_BUFF value
- */
- }
+ if (n) {
+ dev->ack_slot = slot;
+ if (netif_queue_stopped(dev->ndev) &&
+ dev->tx_cnt < EMAC_TX_WAKEUP_THRESH)
+ netif_wake_queue(dev->ndev);
- ep->tx_cnt = 0;
- ep->tx_slot = 0;
- ep->ack_slot = 0;
+ DBG2("%d: tx %d pkts" NL, dev->def->index, n);
+ }
+ }
}
-static void emac_reset_configure(struct ocp_enet_private *fep)
+static inline void emac_recycle_rx_skb(struct ocp_enet_private *dev, int slot,
+ int len)
{
- emac_t *emacp = fep->emacp;
- int i;
+ struct sk_buff *skb = dev->rx_skb[slot];
+ DBG2("%d: recycle %d %d" NL, dev->def->index, slot, len);
- mal_disable_tx_channels(fep->mal, fep->commac.tx_chan_mask);
- mal_disable_rx_channels(fep->mal, fep->commac.rx_chan_mask);
+ if (len)
+ dma_map_single(dev->ldev, skb->data - 2,
+ EMAC_DMA_ALIGN(len + 2), DMA_FROM_DEVICE);
- /*
- * Check for a link, some PHYs don't provide a clock if
- * no link is present. Some EMACs will not come out of
- * soft reset without a PHY clock present.
- */
- if (fep->phy_mii.def->ops->poll_link(&fep->phy_mii)) {
- /* Reset the EMAC */
- out_be32(&emacp->em0mr0, EMAC_M0_SRST);
- udelay(20);
- for (i = 0; i < 100; i++) {
- if ((in_be32(&emacp->em0mr0) & EMAC_M0_SRST) == 0)
- break;
- udelay(10);
- }
+ dev->rx_desc[slot].data_len = 0;
+ barrier();
+ dev->rx_desc[slot].ctrl = MAL_RX_CTRL_EMPTY |
+ (slot == (NUM_RX_BUFF - 1) ? MAL_RX_CTRL_WRAP : 0);
+}
+
+static void emac_parse_rx_error(struct ocp_enet_private *dev, u16 ctrl)
+{
+ struct ibm_emac_error_stats *st = &dev->estats;
+ DBG("%d: BD RX error %04x" NL, dev->def->index, ctrl);
+
+ ++st->rx_bd_errors;
+ if (ctrl & EMAC_RX_ST_OE)
+ ++st->rx_bd_overrun;
+ if (ctrl & EMAC_RX_ST_BP)
+ ++st->rx_bd_bad_packet;
+ if (ctrl & EMAC_RX_ST_RP)
+ ++st->rx_bd_runt_packet;
+ if (ctrl & EMAC_RX_ST_SE)
+ ++st->rx_bd_short_event;
+ if (ctrl & EMAC_RX_ST_AE)
+ ++st->rx_bd_alignment_error;
+ if (ctrl & EMAC_RX_ST_BFCS)
+ ++st->rx_bd_bad_fcs;
+ if (ctrl & EMAC_RX_ST_PTL)
+ ++st->rx_bd_packet_too_long;
+ if (ctrl & EMAC_RX_ST_ORE)
+ ++st->rx_bd_out_of_range;
+ if (ctrl & EMAC_RX_ST_IRE)
+ ++st->rx_bd_in_range;
+}
+
+static inline void emac_rx_csum(struct ocp_enet_private *dev,
+ struct sk_buff *skb, u16 ctrl)
+{
+#if defined(CONFIG_IBM_EMAC_TAH)
+ if (!ctrl && dev->tah_dev) {
+ skb->ip_summed = CHECKSUM_UNNECESSARY;
+ ++dev->stats.rx_packets_csum;
+ }
+#endif
+}
- if (i >= 100) {
- printk(KERN_ERR "%s: Cannot reset EMAC\n",
- fep->ndev->name);
- return;
+static inline int emac_rx_sg_append(struct ocp_enet_private *dev, int slot)
+{
+ if (likely(dev->rx_sg_skb != NULL)) {
+ int len = dev->rx_desc[slot].data_len;
+ int tot_len = dev->rx_sg_skb->len + len;
+
+ if (unlikely(tot_len + 2 > dev->rx_skb_size)) {
+ ++dev->estats.rx_dropped_mtu;
+ dev_kfree_skb(dev->rx_sg_skb);
+ dev->rx_sg_skb = NULL;
+ } else {
+ cacheable_memcpy(dev->rx_sg_skb->tail,
+ dev->rx_skb[slot]->data, len);
+ skb_put(dev->rx_sg_skb, len);
+ emac_recycle_rx_skb(dev, slot, len);
+ return 0;
}
}
+ emac_recycle_rx_skb(dev, slot, 0);
+ return -1;
+}
- /* Switch IRQs off for now */
- out_be32(&emacp->em0iser, 0);
+/* BHs disabled */
+static int emac_poll_rx(void *param, int budget)
+{
+ struct ocp_enet_private *dev = param;
+ int slot = dev->rx_slot, received = 0;
+
+ DBG2("%d: poll_rx(%d)" NL, dev->def->index, budget);
- /* Configure MAL rx channel */
- mal_set_rcbs(fep->mal, fep->mal_rx_chan, DESC_BUF_SIZE_REG);
+ again:
+ while (budget > 0) {
+ int len;
+ struct sk_buff *skb;
+ u16 ctrl = dev->rx_desc[slot].ctrl;
+
+ if (ctrl & MAL_RX_CTRL_EMPTY)
+ break;
- /* set the high address */
- out_be32(&emacp->em0iahr,
- (fep->ndev->dev_addr[0] << 8) | fep->ndev->dev_addr[1]);
+ skb = dev->rx_skb[slot];
+ barrier();
+ len = dev->rx_desc[slot].data_len;
- /* set the low address */
- out_be32(&emacp->em0ialr,
- (fep->ndev->dev_addr[2] << 24) | (fep->ndev->dev_addr[3] << 16)
- | (fep->ndev->dev_addr[4] << 8) | fep->ndev->dev_addr[5]);
+ if (unlikely(!MAL_IS_SINGLE_RX(ctrl)))
+ goto sg;
- /* Adjust to link */
- if (netif_carrier_ok(fep->ndev))
- emac_adjust_to_link(fep);
+ ctrl &= EMAC_BAD_RX_MASK;
+ if (unlikely(ctrl && ctrl != EMAC_RX_TAH_BAD_CSUM)) {
+ emac_parse_rx_error(dev, ctrl);
+ ++dev->estats.rx_dropped_error;
+ emac_recycle_rx_skb(dev, slot, 0);
+ len = 0;
+ goto next;
+ }
- /* enable broadcast/individual address and RX FIFO defaults */
- out_be32(&emacp->em0rmr, EMAC_RMR_DEFAULT);
+ if (len && len < EMAC_RX_COPY_THRESH) {
+ struct sk_buff *copy_skb =
+ alloc_skb(len + EMAC_RX_SKB_HEADROOM + 2, GFP_ATOMIC);
+ if (unlikely(!copy_skb))
+ goto oom;
+
+ skb_reserve(copy_skb, EMAC_RX_SKB_HEADROOM + 2);
+ cacheable_memcpy(copy_skb->data - 2, skb->data - 2,
+ len + 2);
+ emac_recycle_rx_skb(dev, slot, len);
+ skb = copy_skb;
+ } else if (unlikely(emac_alloc_rx_skb(dev, slot, GFP_ATOMIC)))
+ goto oom;
+
+ skb_put(skb, len);
+ push_packet:
+ skb->dev = dev->ndev;
+ skb->protocol = eth_type_trans(skb, dev->ndev);
+ emac_rx_csum(dev, skb, ctrl);
+
+ if (unlikely(netif_receive_skb(skb) == NET_RX_DROP))
+ ++dev->estats.rx_dropped_stack;
+ next:
+ ++dev->stats.rx_packets;
+ skip:
+ dev->stats.rx_bytes += len;
+ slot = (slot + 1) % NUM_RX_BUFF;
+ --budget;
+ ++received;
+ continue;
+ sg:
+ if (ctrl & MAL_RX_CTRL_FIRST) {
+ BUG_ON(dev->rx_sg_skb);
+ if (unlikely(emac_alloc_rx_skb(dev, slot, GFP_ATOMIC))) {
+ DBG("%d: rx OOM %d" NL, dev->def->index, slot);
+ ++dev->estats.rx_dropped_oom;
+ emac_recycle_rx_skb(dev, slot, 0);
+ } else {
+ dev->rx_sg_skb = skb;
+ skb_put(skb, len);
+ }
+ } else if (!emac_rx_sg_append(dev, slot) &&
+ (ctrl & MAL_RX_CTRL_LAST)) {
+
+ skb = dev->rx_sg_skb;
+ dev->rx_sg_skb = NULL;
+
+ ctrl &= EMAC_BAD_RX_MASK;
+ if (unlikely(ctrl && ctrl != EMAC_RX_TAH_BAD_CSUM)) {
+ emac_parse_rx_error(dev, ctrl);
+ ++dev->estats.rx_dropped_error;
+ dev_kfree_skb(skb);
+ len = 0;
+ } else
+ goto push_packet;
+ }
+ goto skip;
+ oom:
+ DBG("%d: rx OOM %d" NL, dev->def->index, slot);
+ /* Drop the packet and recycle skb */
+ ++dev->estats.rx_dropped_oom;
+ emac_recycle_rx_skb(dev, slot, 0);
+ goto next;
+ }
- /* set transmit request threshold register */
- out_be32(&emacp->em0trtr, EMAC_TRTR_DEFAULT);
+ if (received) {
+ DBG2("%d: rx %d BDs" NL, dev->def->index, received);
+ dev->rx_slot = slot;
+ }
- /* Reconfigure multicast */
- __emac_set_multicast_list(fep->ndev);
+ if (unlikely(budget && dev->commac.rx_stopped)) {
+ struct ocp_func_emac_data *emacdata = dev->def->additions;
- /* Set receiver/transmitter defaults */
- out_be32(&emacp->em0rwmr, EMAC_RWMR_DEFAULT);
- out_be32(&emacp->em0tmr0, EMAC_TMR0_DEFAULT);
- out_be32(&emacp->em0tmr1, EMAC_TMR1_DEFAULT);
+ barrier();
+ if (!(dev->rx_desc[slot].ctrl & MAL_RX_CTRL_EMPTY)) {
+ DBG2("%d: rx restart" NL, dev->def->index);
+ received = 0;
+ goto again;
+ }
- /* set frame gap */
- out_be32(&emacp->em0ipgvr, CONFIG_IBM_EMAC_FGAP);
-
- /* set VLAN Tag Protocol Identifier */
- out_be32(&emacp->em0vtpid, 0x8100);
+ if (dev->rx_sg_skb) {
+ DBG2("%d: dropping partial rx packet" NL,
+ dev->def->index);
+ ++dev->estats.rx_dropped_error;
+ dev_kfree_skb(dev->rx_sg_skb);
+ dev->rx_sg_skb = NULL;
+ }
- /* Init ring buffers */
- emac_init_rings(fep->ndev);
+ dev->commac.rx_stopped = 0;
+ mal_enable_rx_channel(dev->mal, emacdata->mal_rx_chan);
+ emac_rx_enable(dev);
+ dev->rx_slot = 0;
+ }
+ return received;
}
-static void emac_kick(struct ocp_enet_private *fep)
+/* BHs disabled */
+static int emac_peek_rx(void *param)
{
- emac_t *emacp = fep->emacp;
- unsigned long emac_ier;
-
- emac_ier = EMAC_ISR_PP | EMAC_ISR_BP | EMAC_ISR_RP |
- EMAC_ISR_SE | EMAC_ISR_PTLE | EMAC_ISR_ALE |
- EMAC_ISR_BFCS | EMAC_ISR_ORE | EMAC_ISR_IRE;
+ struct ocp_enet_private *dev = param;
+ return !(dev->rx_desc[dev->rx_slot].ctrl & MAL_RX_CTRL_EMPTY);
+}
- out_be32(&emacp->em0iser, emac_ier);
+/* BHs disabled */
+static int emac_peek_rx_sg(void *param)
+{
+ struct ocp_enet_private *dev = param;
+ int slot = dev->rx_slot;
+ while (1) {
+ u16 ctrl = dev->rx_desc[slot].ctrl;
+ if (ctrl & MAL_RX_CTRL_EMPTY)
+ return 0;
+ else if (ctrl & MAL_RX_CTRL_LAST)
+ return 1;
- /* enable all MAL transmit and receive channels */
- mal_enable_tx_channels(fep->mal, fep->commac.tx_chan_mask);
- mal_enable_rx_channels(fep->mal, fep->commac.rx_chan_mask);
+ slot = (slot + 1) % NUM_RX_BUFF;
- /* set transmit and receive enable */
- out_be32(&emacp->em0mr0, EMAC_M0_TXE | EMAC_M0_RXE);
+ /* I'm just being paranoid here :) */
+ if (unlikely(slot == dev->rx_slot))
+ return 0;
+ }
}
-static void
-emac_start_link(struct ocp_enet_private *fep, struct ethtool_cmd *ep)
+/* Hard IRQ */
+static void emac_rxde(void *param)
{
- u32 advertise;
- int autoneg;
- int forced_speed;
- int forced_duplex;
+ struct ocp_enet_private *dev = param;
+ ++dev->estats.rx_stopped;
+ emac_rx_disable_async(dev);
+}
- /* Default advertise */
- advertise = ADVERTISED_10baseT_Half | ADVERTISED_10baseT_Full |
- ADVERTISED_100baseT_Half | ADVERTISED_100baseT_Full |
- ADVERTISED_1000baseT_Half | ADVERTISED_1000baseT_Full;
- autoneg = fep->want_autoneg;
- forced_speed = fep->phy_mii.speed;
- forced_duplex = fep->phy_mii.duplex;
+/* Hard IRQ */
+static irqreturn_t emac_irq(int irq, void *dev_instance, struct pt_regs *regs)
+{
+ struct ocp_enet_private *dev = dev_instance;
+ struct emac_regs *p = dev->emacp;
+ struct ibm_emac_error_stats *st = &dev->estats;
+
+ u32 isr = in_be32(&p->isr);
+ out_be32(&p->isr, isr);
+
+ DBG("%d: isr = %08x" NL, dev->def->index, isr);
+
+ if (isr & EMAC_ISR_TXPE)
+ ++st->tx_parity;
+ if (isr & EMAC_ISR_RXPE)
+ ++st->rx_parity;
+ if (isr & EMAC_ISR_TXUE)
+ ++st->tx_underrun;
+ if (isr & EMAC_ISR_RXOE)
+ ++st->rx_fifo_overrun;
+ if (isr & EMAC_ISR_OVR)
+ ++st->rx_overrun;
+ if (isr & EMAC_ISR_BP)
+ ++st->rx_bad_packet;
+ if (isr & EMAC_ISR_RP)
+ ++st->rx_runt_packet;
+ if (isr & EMAC_ISR_SE)
+ ++st->rx_short_event;
+ if (isr & EMAC_ISR_ALE)
+ ++st->rx_alignment_error;
+ if (isr & EMAC_ISR_BFCS)
+ ++st->rx_bad_fcs;
+ if (isr & EMAC_ISR_PTLE)
+ ++st->rx_packet_too_long;
+ if (isr & EMAC_ISR_ORE)
+ ++st->rx_out_of_range;
+ if (isr & EMAC_ISR_IRE)
+ ++st->rx_in_range;
+ if (isr & EMAC_ISR_SQE)
+ ++st->tx_sqe;
+ if (isr & EMAC_ISR_TE)
+ ++st->tx_errors;
- /* Setup link parameters */
- if (ep) {
- if (ep->autoneg == AUTONEG_ENABLE) {
- advertise = ep->advertising;
- autoneg = 1;
- } else {
- autoneg = 0;
- forced_speed = ep->speed;
- forced_duplex = ep->duplex;
- }
- }
+ return IRQ_HANDLED;
+}
- /* Configure PHY & start aneg */
- fep->want_autoneg = autoneg;
- if (autoneg) {
- LINK_DEBUG(("%s: start link aneg, advertise: 0x%x\n",
- fep->ndev->name, advertise));
- fep->phy_mii.def->ops->setup_aneg(&fep->phy_mii, advertise);
- } else {
- LINK_DEBUG(("%s: start link forced, speed: %d, duplex: %d\n",
- fep->ndev->name, forced_speed, forced_duplex));
- fep->phy_mii.def->ops->setup_forced(&fep->phy_mii, forced_speed,
- forced_duplex);
- }
- fep->timer_ticks = 0;
- mod_timer(&fep->link_timer, jiffies + HZ);
+static struct net_device_stats *emac_stats(struct net_device *ndev)
+{
+ struct ocp_enet_private *dev = ndev->priv;
+ struct ibm_emac_stats *st = &dev->stats;
+ struct ibm_emac_error_stats *est = &dev->estats;
+ struct net_device_stats *nst = &dev->nstats;
+
+ DBG2("%d: stats" NL, dev->def->index);
+
+ /* Compute "legacy" statistics */
+ local_irq_disable();
+ nst->rx_packets = (unsigned long)st->rx_packets;
+ nst->rx_bytes = (unsigned long)st->rx_bytes;
+ nst->tx_packets = (unsigned long)st->tx_packets;
+ nst->tx_bytes = (unsigned long)st->tx_bytes;
+ nst->rx_dropped = (unsigned long)(est->rx_dropped_oom +
+ est->rx_dropped_error +
+ est->rx_dropped_resize +
+ est->rx_dropped_mtu);
+ nst->tx_dropped = (unsigned long)est->tx_dropped;
+
+ nst->rx_errors = (unsigned long)est->rx_bd_errors;
+ nst->rx_fifo_errors = (unsigned long)(est->rx_bd_overrun +
+ est->rx_fifo_overrun +
+ est->rx_overrun);
+ nst->rx_frame_errors = (unsigned long)(est->rx_bd_alignment_error +
+ est->rx_alignment_error);
+ nst->rx_crc_errors = (unsigned long)(est->rx_bd_bad_fcs +
+ est->rx_bad_fcs);
+ nst->rx_length_errors = (unsigned long)(est->rx_bd_runt_packet +
+ est->rx_bd_short_event +
+ est->rx_bd_packet_too_long +
+ est->rx_bd_out_of_range +
+ est->rx_bd_in_range +
+ est->rx_runt_packet +
+ est->rx_short_event +
+ est->rx_packet_too_long +
+ est->rx_out_of_range +
+ est->rx_in_range);
+
+ nst->tx_errors = (unsigned long)(est->tx_bd_errors + est->tx_errors);
+ nst->tx_fifo_errors = (unsigned long)(est->tx_bd_underrun +
+ est->tx_underrun);
+ nst->tx_carrier_errors = (unsigned long)est->tx_bd_carrier_loss;
+ nst->collisions = (unsigned long)(est->tx_bd_excessive_deferral +
+ est->tx_bd_excessive_collisions +
+ est->tx_bd_late_collision +
+ est->tx_bd_multple_collisions);
+ local_irq_enable();
+ return nst;
}
-static void emac_link_timer(unsigned long data)
+static void emac_remove(struct ocp_device *ocpdev)
{
- struct ocp_enet_private *fep = (struct ocp_enet_private *)data;
- int link;
+ struct ocp_enet_private *dev = ocp_get_drvdata(ocpdev);
- if (fep->going_away)
- return;
+ DBG("%d: remove" NL, dev->def->index);
- spin_lock_irq(&fep->lock);
+ ocp_set_drvdata(ocpdev, 0);
+ unregister_netdev(dev->ndev);
- link = fep->phy_mii.def->ops->poll_link(&fep->phy_mii);
- LINK_DEBUG(("%s: poll_link: %d\n", fep->ndev->name, link));
+ tah_fini(dev->tah_dev);
+ rgmii_fini(dev->rgmii_dev, dev->rgmii_input);
+ zmii_fini(dev->zmii_dev, dev->zmii_input);
- if (link == netif_carrier_ok(fep->ndev)) {
- if (!link && fep->want_autoneg && (++fep->timer_ticks) > 10)
- emac_start_link(fep, NULL);
- goto out;
- }
- printk(KERN_INFO "%s: Link is %s\n", fep->ndev->name,
- link ? "Up" : "Down");
- if (link) {
- netif_carrier_on(fep->ndev);
- /* Chip needs a full reset on config change. That sucks, so I
- * should ultimately move that to some tasklet to limit
- * latency peaks caused by this code
- */
- emac_reset_configure(fep);
- if (fep->opened)
- emac_kick(fep);
- } else {
- fep->timer_ticks = 0;
- netif_carrier_off(fep->ndev);
- }
- out:
- mod_timer(&fep->link_timer, jiffies + HZ);
- spin_unlock_irq(&fep->lock);
+ emac_dbg_register(dev->def->index, 0);
+
+ mal_unregister_commac(dev->mal, &dev->commac);
+ iounmap((void *)dev->emacp);
+ kfree(dev->ndev);
}
-static void emac_set_multicast_list(struct net_device *dev)
-{
- struct ocp_enet_private *fep = dev->priv;
+static struct mal_commac_ops emac_commac_ops = {
+ .poll_tx = &emac_poll_tx,
+ .poll_rx = &emac_poll_rx,
+ .peek_rx = &emac_peek_rx,
+ .rxde = &emac_rxde,
+};
- spin_lock_irq(&fep->lock);
- __emac_set_multicast_list(dev);
- spin_unlock_irq(&fep->lock);
-}
+static struct mal_commac_ops emac_commac_sg_ops = {
+ .poll_tx = &emac_poll_tx,
+ .poll_rx = &emac_poll_rx,
+ .peek_rx = &emac_peek_rx_sg,
+ .rxde = &emac_rxde,
+};
-static int emac_get_settings(struct net_device *ndev, struct ethtool_cmd *cmd)
+/* Ethtool support */
+static int emac_ethtool_get_settings(struct net_device *ndev,
+ struct ethtool_cmd *cmd)
{
- struct ocp_enet_private *fep = ndev->priv;
+ struct ocp_enet_private *dev = ndev->priv;
- cmd->supported = fep->phy_mii.def->features;
+ cmd->supported = dev->phy.features;
cmd->port = PORT_MII;
- cmd->transceiver = XCVR_EXTERNAL;
- cmd->phy_address = fep->mii_phy_addr;
- spin_lock_irq(&fep->lock);
- cmd->autoneg = fep->want_autoneg;
- cmd->speed = fep->phy_mii.speed;
- cmd->duplex = fep->phy_mii.duplex;
- spin_unlock_irq(&fep->lock);
+ cmd->phy_address = dev->phy.address;
+ cmd->transceiver =
+ dev->phy.address >= 0 ? XCVR_EXTERNAL : XCVR_INTERNAL;
+
+ local_bh_disable();
+ cmd->advertising = dev->phy.advertising;
+ cmd->autoneg = dev->phy.autoneg;
+ cmd->speed = dev->phy.speed;
+ cmd->duplex = dev->phy.duplex;
+ local_bh_enable();
+
return 0;
}
-static int emac_set_settings(struct net_device *ndev, struct ethtool_cmd *cmd)
+static int emac_ethtool_set_settings(struct net_device *ndev,
+ struct ethtool_cmd *cmd)
{
- struct ocp_enet_private *fep = ndev->priv;
- unsigned long features = fep->phy_mii.def->features;
+ struct ocp_enet_private *dev = ndev->priv;
+ u32 f = dev->phy.features;
- if (!capable(CAP_NET_ADMIN))
- return -EPERM;
+ DBG("%d: set_settings(%d, %d, %d, 0x%08x)" NL, dev->def->index,
+ cmd->autoneg, cmd->speed, cmd->duplex, cmd->advertising);
+ /* Basic sanity checks */
+ if (dev->phy.address < 0)
+ return -EOPNOTSUPP;
if (cmd->autoneg != AUTONEG_ENABLE && cmd->autoneg != AUTONEG_DISABLE)
return -EINVAL;
if (cmd->autoneg == AUTONEG_ENABLE && cmd->advertising == 0)
return -EINVAL;
if (cmd->duplex != DUPLEX_HALF && cmd->duplex != DUPLEX_FULL)
return -EINVAL;
- if (cmd->autoneg == AUTONEG_DISABLE)
+
+ if (cmd->autoneg == AUTONEG_DISABLE) {
switch (cmd->speed) {
case SPEED_10:
- if (cmd->duplex == DUPLEX_HALF &&
- (features & SUPPORTED_10baseT_Half) == 0)
+ if (cmd->duplex == DUPLEX_HALF
+ && !(f & SUPPORTED_10baseT_Half))
return -EINVAL;
- if (cmd->duplex == DUPLEX_FULL &&
- (features & SUPPORTED_10baseT_Full) == 0)
+ if (cmd->duplex == DUPLEX_FULL
+ && !(f & SUPPORTED_10baseT_Full))
return -EINVAL;
break;
case SPEED_100:
- if (cmd->duplex == DUPLEX_HALF &&
- (features & SUPPORTED_100baseT_Half) == 0)
+ if (cmd->duplex == DUPLEX_HALF
+ && !(f & SUPPORTED_100baseT_Half))
return -EINVAL;
- if (cmd->duplex == DUPLEX_FULL &&
- (features & SUPPORTED_100baseT_Full) == 0)
+ if (cmd->duplex == DUPLEX_FULL
+ && !(f & SUPPORTED_100baseT_Full))
return -EINVAL;
break;
case SPEED_1000:
- if (cmd->duplex == DUPLEX_HALF &&
- (features & SUPPORTED_1000baseT_Half) == 0)
+ if (cmd->duplex == DUPLEX_HALF
+ && !(f & SUPPORTED_1000baseT_Half))
return -EINVAL;
- if (cmd->duplex == DUPLEX_FULL &&
- (features & SUPPORTED_1000baseT_Full) == 0)
+ if (cmd->duplex == DUPLEX_FULL
+ && !(f & SUPPORTED_1000baseT_Full))
return -EINVAL;
break;
default:
return -EINVAL;
- } else if ((features & SUPPORTED_Autoneg) == 0)
- return -EINVAL;
- spin_lock_irq(&fep->lock);
- emac_start_link(fep, cmd);
- spin_unlock_irq(&fep->lock);
+ }
+
+ local_bh_disable();
+ dev->phy.def->ops->setup_forced(&dev->phy, cmd->speed,
+ cmd->duplex);
+
+ } else {
+ if (!(f & SUPPORTED_Autoneg))
+ return -EINVAL;
+
+ local_bh_disable();
+ dev->phy.def->ops->setup_aneg(&dev->phy,
+ (cmd->advertising & f) |
+ (dev->phy.advertising &
+ (ADVERTISED_Pause |
+ ADVERTISED_Asym_Pause)));
+ }
+ emac_force_link_update(dev);
+ local_bh_enable();
+
return 0;
}
-static void
-emac_get_drvinfo(struct net_device *ndev, struct ethtool_drvinfo *info)
+static void emac_ethtool_get_ringparam(struct net_device *ndev,
+ struct ethtool_ringparam *rp)
{
- struct ocp_enet_private *fep = ndev->priv;
-
- strcpy(info->driver, DRV_NAME);
- strcpy(info->version, DRV_VERSION);
- info->fw_version[0] = '\0';
- sprintf(info->bus_info, "IBM EMAC %d", fep->ocpdev->def->index);
- info->regdump_len = 0;
+ rp->rx_max_pending = rp->rx_pending = NUM_RX_BUFF;
+ rp->tx_max_pending = rp->tx_pending = NUM_TX_BUFF;
}
-static int emac_nway_reset(struct net_device *ndev)
+static void emac_ethtool_get_pauseparam(struct net_device *ndev,
+ struct ethtool_pauseparam *pp)
{
- struct ocp_enet_private *fep = ndev->priv;
+ struct ocp_enet_private *dev = ndev->priv;
+
+ local_bh_disable();
+ if ((dev->phy.features & SUPPORTED_Autoneg) &&
+ (dev->phy.advertising & (ADVERTISED_Pause | ADVERTISED_Asym_Pause)))
+ pp->autoneg = 1;
+
+ if (dev->phy.duplex == DUPLEX_FULL) {
+ if (dev->phy.pause)
+ pp->rx_pause = pp->tx_pause = 1;
+ else if (dev->phy.asym_pause)
+ pp->tx_pause = 1;
+ }
+ local_bh_enable();
+}
- if (!fep->want_autoneg)
- return -EINVAL;
- spin_lock_irq(&fep->lock);
- emac_start_link(fep, NULL);
- spin_unlock_irq(&fep->lock);
- return 0;
+static u32 emac_ethtool_get_rx_csum(struct net_device *ndev)
+{
+ struct ocp_enet_private *dev = ndev->priv;
+ return dev->tah_dev != 0;
}
-static u32 emac_get_link(struct net_device *ndev)
+static int emac_get_regs_len(struct ocp_enet_private *dev)
{
- return netif_carrier_ok(ndev);
+ return sizeof(struct emac_ethtool_regs_subhdr) + EMAC_ETHTOOL_REGS_SIZE;
}
-static struct ethtool_ops emac_ethtool_ops = {
- .get_settings = emac_get_settings,
- .set_settings = emac_set_settings,
- .get_drvinfo = emac_get_drvinfo,
- .nway_reset = emac_nway_reset,
- .get_link = emac_get_link
-};
+static int emac_ethtool_get_regs_len(struct net_device *ndev)
+{
+ struct ocp_enet_private *dev = ndev->priv;
+ return sizeof(struct emac_ethtool_regs_hdr) +
+ emac_get_regs_len(dev) + mal_get_regs_len(dev->mal) +
+ zmii_get_regs_len(dev->zmii_dev) +
+ rgmii_get_regs_len(dev->rgmii_dev) +
+ tah_get_regs_len(dev->tah_dev);
+}
-static int emac_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
+static void *emac_dump_regs(struct ocp_enet_private *dev, void *buf)
{
- struct ocp_enet_private *fep = dev->priv;
- uint16_t *data = (uint16_t *) & rq->ifr_ifru;
+ struct emac_ethtool_regs_subhdr *hdr = buf;
- switch (cmd) {
- case SIOCGMIIPHY:
- data[0] = fep->mii_phy_addr;
- /* Fall through */
- case SIOCGMIIREG:
- data[3] = emac_phy_read(dev, fep->mii_phy_addr, data[1]);
- return 0;
- case SIOCSMIIREG:
- if (!capable(CAP_NET_ADMIN))
- return -EPERM;
+ hdr->version = EMAC_ETHTOOL_REGS_VER;
+ hdr->index = dev->def->index;
+ memcpy_fromio(hdr + 1, dev->emacp, EMAC_ETHTOOL_REGS_SIZE);
+ return ((void *)(hdr + 1) + EMAC_ETHTOOL_REGS_SIZE);
+}
- emac_phy_write(dev, fep->mii_phy_addr, data[1], data[2]);
- return 0;
- default:
- return -EOPNOTSUPP;
+static void emac_ethtool_get_regs(struct net_device *ndev,
+ struct ethtool_regs *regs, void *buf)
+{
+ struct ocp_enet_private *dev = ndev->priv;
+ struct emac_ethtool_regs_hdr *hdr = buf;
+
+ hdr->components = 0;
+ buf = hdr + 1;
+
+ local_irq_disable();
+ buf = mal_dump_regs(dev->mal, buf);
+ buf = emac_dump_regs(dev, buf);
+ if (dev->zmii_dev) {
+ hdr->components |= EMAC_ETHTOOL_REGS_ZMII;
+ buf = zmii_dump_regs(dev->zmii_dev, buf);
+ }
+ if (dev->rgmii_dev) {
+ hdr->components |= EMAC_ETHTOOL_REGS_RGMII;
+ buf = rgmii_dump_regs(dev->rgmii_dev, buf);
}
+ if (dev->tah_dev) {
+ hdr->components |= EMAC_ETHTOOL_REGS_TAH;
+ buf = tah_dump_regs(dev->tah_dev, buf);
+ }
+ local_irq_enable();
}
-static int emac_open(struct net_device *dev)
+static int emac_ethtool_nway_reset(struct net_device *ndev)
{
- struct ocp_enet_private *fep = dev->priv;
- int rc;
+ struct ocp_enet_private *dev = ndev->priv;
+ int res = 0;
- spin_lock_irq(&fep->lock);
+ DBG("%d: nway_reset" NL, dev->def->index);
- fep->opened = 1;
- netif_carrier_off(dev);
+ if (dev->phy.address < 0)
+ return -EOPNOTSUPP;
- /* Reset & configure the chip */
- emac_reset_configure(fep);
+ local_bh_disable();
+ if (!dev->phy.autoneg) {
+ res = -EINVAL;
+ goto out;
+ }
- spin_unlock_irq(&fep->lock);
+ dev->phy.def->ops->setup_aneg(&dev->phy, dev->phy.advertising);
+ emac_force_link_update(dev);
- /* Request our interrupt lines */
- rc = request_irq(dev->irq, emac_mac_irq, 0, "IBM EMAC MAC", dev);
- if (rc != 0) {
- printk("dev->irq %d failed\n", dev->irq);
- goto bail;
- }
- /* Kick the chip rx & tx channels into life */
- spin_lock_irq(&fep->lock);
- emac_kick(fep);
- spin_unlock_irq(&fep->lock);
+ out:
+ local_bh_enable();
+ return res;
+}
- netif_start_queue(dev);
- bail:
- return rc;
+static int emac_ethtool_get_stats_count(struct net_device *ndev)
+{
+ return EMAC_ETHTOOL_STATS_COUNT;
}
-static int emac_close(struct net_device *dev)
+static void emac_ethtool_get_strings(struct net_device *ndev, u32 stringset,
+ u8 * buf)
{
- struct ocp_enet_private *fep = dev->priv;
- emac_t *emacp = fep->emacp;
+ if (stringset == ETH_SS_STATS)
+ memcpy(buf, &emac_stats_keys, sizeof(emac_stats_keys));
+}
- /* XXX Stop IRQ emitting here */
- spin_lock_irq(&fep->lock);
- fep->opened = 0;
- mal_disable_tx_channels(fep->mal, fep->commac.tx_chan_mask);
- mal_disable_rx_channels(fep->mal, fep->commac.rx_chan_mask);
- netif_carrier_off(dev);
- netif_stop_queue(dev);
+static void emac_ethtool_get_ethtool_stats(struct net_device *ndev,
+ struct ethtool_stats *estats,
+ u64 * tmp_stats)
+{
+ struct ocp_enet_private *dev = ndev->priv;
+ local_irq_disable();
+ memcpy(tmp_stats, &dev->stats, sizeof(dev->stats));
+ tmp_stats += sizeof(dev->stats) / sizeof(u64);
+ memcpy(tmp_stats, &dev->estats, sizeof(dev->estats));
+ local_irq_enable();
+}
- /*
- * Check for a link, some PHYs don't provide a clock if
- * no link is present. Some EMACs will not come out of
- * soft reset without a PHY clock present.
- */
- if (fep->phy_mii.def->ops->poll_link(&fep->phy_mii)) {
- out_be32(&emacp->em0mr0, EMAC_M0_SRST);
- udelay(10);
+static void emac_ethtool_get_drvinfo(struct net_device *ndev,
+ struct ethtool_drvinfo *info)
+{
+ struct ocp_enet_private *dev = ndev->priv;
- if (emacp->em0mr0 & EMAC_M0_SRST) {
- /*not sure what to do here hopefully it clears before another open */
- printk(KERN_ERR
- "%s: Phy SoftReset didn't clear, no link?\n",
- dev->name);
- }
- }
+ strcpy(info->driver, "ibm_emac");
+ strcpy(info->version, DRV_VERSION);
+ info->fw_version[0] = '\0';
+ sprintf(info->bus_info, "PPC 4xx EMAC %d", dev->def->index);
+ info->n_stats = emac_ethtool_get_stats_count(ndev);
+ info->regdump_len = emac_ethtool_get_regs_len(ndev);
+}
- /* Free the irq's */
- free_irq(dev->irq, dev);
+static struct ethtool_ops emac_ethtool_ops = {
+ .get_settings = emac_ethtool_get_settings,
+ .set_settings = emac_ethtool_set_settings,
+ .get_drvinfo = emac_ethtool_get_drvinfo,
- spin_unlock_irq(&fep->lock);
+ .get_regs_len = emac_ethtool_get_regs_len,
+ .get_regs = emac_ethtool_get_regs,
- return 0;
-}
+ .nway_reset = emac_ethtool_nway_reset,
-static void emac_remove(struct ocp_device *ocpdev)
-{
- struct net_device *dev = ocp_get_drvdata(ocpdev);
- struct ocp_enet_private *ep = dev->priv;
-
- /* FIXME: locking, races, ... */
- ep->going_away = 1;
- ocp_set_drvdata(ocpdev, NULL);
- if (ep->rgmii_dev)
- emac_close_rgmii(ep->rgmii_dev);
- if (ep->zmii_dev)
- emac_close_zmii(ep->zmii_dev);
-
- unregister_netdev(dev);
- del_timer_sync(&ep->link_timer);
- mal_unregister_commac(ep->mal, &ep->commac);
- iounmap((void *)ep->emacp);
- kfree(dev);
-}
-
-struct mal_commac_ops emac_commac_ops = {
- .txeob = &emac_txeob_dev,
- .txde = &emac_txde_dev,
- .rxeob = &emac_rxeob_dev,
- .rxde = &emac_rxde_dev,
+ .get_ringparam = emac_ethtool_get_ringparam,
+ .get_pauseparam = emac_ethtool_get_pauseparam,
+
+ .get_rx_csum = emac_ethtool_get_rx_csum,
+
+ .get_strings = emac_ethtool_get_strings,
+ .get_stats_count = emac_ethtool_get_stats_count,
+ .get_ethtool_stats = emac_ethtool_get_ethtool_stats,
+
+ .get_link = ethtool_op_get_link,
+ .get_tx_csum = ethtool_op_get_tx_csum,
+ .get_sg = ethtool_op_get_sg,
};
-#ifdef CONFIG_NET_POLL_CONTROLLER
-static void emac_netpoll(struct net_device *ndev)
+static int emac_ioctl(struct net_device *ndev, struct ifreq *rq, int cmd)
{
- emac_rxeob_dev((void *)ndev, 0);
- emac_txeob_dev((void *)ndev, 0);
+ struct ocp_enet_private *dev = ndev->priv;
+ uint16_t *data = (uint16_t *) & rq->ifr_ifru;
+
+ DBG("%d: ioctl %08x" NL, dev->def->index, cmd);
+
+ if (dev->phy.address < 0)
+ return -EOPNOTSUPP;
+
+ switch (cmd) {
+ case SIOCGMIIPHY:
+ case SIOCDEVPRIVATE:
+ data[0] = dev->phy.address;
+ /* Fall through */
+ case SIOCGMIIREG:
+ case SIOCDEVPRIVATE + 1:
+ data[3] = emac_mdio_read(ndev, dev->phy.address, data[1]);
+ return 0;
+
+ case SIOCSMIIREG:
+ case SIOCDEVPRIVATE + 2:
+ if (!capable(CAP_NET_ADMIN))
+ return -EPERM;
+ emac_mdio_write(ndev, dev->phy.address, data[1], data[2]);
+ return 0;
+ default:
+ return -EOPNOTSUPP;
+ }
}
-#endif
-static int emac_init_device(struct ocp_device *ocpdev, struct ibm_ocp_mal *mal)
+static int __init emac_probe(struct ocp_device *ocpdev)
{
- int deferred_init = 0;
- int rc = 0, i;
+ struct ocp_func_emac_data *emacdata = ocpdev->def->additions;
struct net_device *ndev;
- struct ocp_enet_private *ep;
- struct ocp_func_emac_data *emacdata;
- int commac_reg = 0;
- u32 phy_map;
+ struct ocp_device *maldev;
+ struct ocp_enet_private *dev;
+ int err, i;
+
+ DBG("%d: probe" NL, ocpdev->def->index);
- emacdata = (struct ocp_func_emac_data *)ocpdev->def->additions;
if (!emacdata) {
printk(KERN_ERR "emac%d: Missing additional data!\n",
ocpdev->def->index);
/* Allocate our net_device structure */
ndev = alloc_etherdev(sizeof(struct ocp_enet_private));
- if (ndev == NULL) {
- printk(KERN_ERR
- "emac%d: Could not allocate ethernet device.\n",
+ if (!ndev) {
+ printk(KERN_ERR "emac%d: could not allocate ethernet device!\n",
ocpdev->def->index);
return -ENOMEM;
}
- ep = ndev->priv;
- ep->ndev = ndev;
- ep->ocpdev = ocpdev;
- ndev->irq = ocpdev->def->irq;
- ep->wol_irq = emacdata->wol_irq;
- if (emacdata->mdio_idx >= 0) {
- if (emacdata->mdio_idx == ocpdev->def->index) {
- /* Set the common MDIO net_device */
- mdio_ndev = ndev;
- deferred_init = 1;
- }
- ep->mdio_dev = mdio_ndev;
- } else {
- ep->mdio_dev = ndev;
- }
+ dev = ndev->priv;
+ dev->ndev = ndev;
+ dev->ldev = &ocpdev->dev;
+ dev->def = ocpdev->def;
+ SET_MODULE_OWNER(ndev);
- ocp_set_drvdata(ocpdev, ndev);
-
- spin_lock_init(&ep->lock);
-
- /* Fill out MAL informations and register commac */
- ep->mal = mal;
- ep->mal_tx_chan = emacdata->mal_tx_chan;
- ep->mal_rx_chan = emacdata->mal_rx_chan;
- ep->commac.ops = &emac_commac_ops;
- ep->commac.dev = ndev;
- ep->commac.tx_chan_mask = MAL_CHAN_MASK(ep->mal_tx_chan);
- ep->commac.rx_chan_mask = MAL_CHAN_MASK(ep->mal_rx_chan);
- rc = mal_register_commac(ep->mal, &ep->commac);
- if (rc != 0)
- goto bail;
- commac_reg = 1;
-
- /* Map our MMIOs */
- ep->emacp = (emac_t *) ioremap(ocpdev->def->paddr, sizeof(emac_t));
-
- /* Check if we need to attach to a ZMII */
- if (emacdata->zmii_idx >= 0) {
- ep->zmii_input = emacdata->zmii_mux;
- ep->zmii_dev =
- ocp_find_device(OCP_ANY_ID, OCP_FUNC_ZMII,
- emacdata->zmii_idx);
- if (ep->zmii_dev == NULL)
- printk(KERN_WARNING
- "emac%d: ZMII %d requested but not found !\n",
- ocpdev->def->index, emacdata->zmii_idx);
- else if ((rc =
- emac_init_zmii(ep->zmii_dev, ep->zmii_input,
- emacdata->phy_mode)) != 0)
- goto bail;
+ /* Find MAL device we are connected to */
+ maldev =
+ ocp_find_device(OCP_VENDOR_IBM, OCP_FUNC_MAL, emacdata->mal_idx);
+ if (!maldev) {
+ printk(KERN_ERR "emac%d: unknown mal%d device!\n",
+ dev->def->index, emacdata->mal_idx);
+ err = -ENODEV;
+ goto out;
+ }
+ dev->mal = ocp_get_drvdata(maldev);
+ if (!dev->mal) {
+ printk(KERN_ERR "emac%d: mal%d hasn't been initialized yet!\n",
+ dev->def->index, emacdata->mal_idx);
+ err = -ENODEV;
+ goto out;
}
- /* Check if we need to attach to a RGMII */
- if (emacdata->rgmii_idx >= 0) {
- ep->rgmii_input = emacdata->rgmii_mux;
- ep->rgmii_dev =
- ocp_find_device(OCP_ANY_ID, OCP_FUNC_RGMII,
- emacdata->rgmii_idx);
- if (ep->rgmii_dev == NULL)
- printk(KERN_WARNING
- "emac%d: RGMII %d requested but not found !\n",
- ocpdev->def->index, emacdata->rgmii_idx);
- else if ((rc =
- emac_init_rgmii(ep->rgmii_dev, ep->rgmii_input,
- emacdata->phy_mode)) != 0)
- goto bail;
+ /* Register with MAL */
+ dev->commac.ops = &emac_commac_ops;
+ dev->commac.dev = dev;
+ dev->commac.tx_chan_mask = MAL_CHAN_MASK(emacdata->mal_tx_chan);
+ dev->commac.rx_chan_mask = MAL_CHAN_MASK(emacdata->mal_rx_chan);
+ err = mal_register_commac(dev->mal, &dev->commac);
+ if (err) {
+ printk(KERN_ERR "emac%d: failed to register with mal%d!\n",
+ dev->def->index, emacdata->mal_idx);
+ goto out;
+ }
+ dev->rx_skb_size = emac_rx_skb_size(ndev->mtu);
+ dev->rx_sync_size = emac_rx_sync_size(ndev->mtu);
+
+ /* Get pointers to BD rings */
+ dev->tx_desc =
+ dev->mal->bd_virt + mal_tx_bd_offset(dev->mal,
+ emacdata->mal_tx_chan);
+ dev->rx_desc =
+ dev->mal->bd_virt + mal_rx_bd_offset(dev->mal,
+ emacdata->mal_rx_chan);
+
+ DBG("%d: tx_desc %p" NL, ocpdev->def->index, dev->tx_desc);
+ DBG("%d: rx_desc %p" NL, ocpdev->def->index, dev->rx_desc);
+
+ /* Clean rings */
+ memset(dev->tx_desc, 0, NUM_TX_BUFF * sizeof(struct mal_descriptor));
+ memset(dev->rx_desc, 0, NUM_RX_BUFF * sizeof(struct mal_descriptor));
+
+ /* If we depend on another EMAC for MDIO, check whether it was probed already */
+ if (emacdata->mdio_idx >= 0 && emacdata->mdio_idx != ocpdev->def->index) {
+ struct ocp_device *mdiodev =
+ ocp_find_device(OCP_VENDOR_IBM, OCP_FUNC_EMAC,
+ emacdata->mdio_idx);
+ if (!mdiodev) {
+ printk(KERN_ERR "emac%d: unknown emac%d device!\n",
+ dev->def->index, emacdata->mdio_idx);
+ err = -ENODEV;
+ goto out2;
+ }
+ dev->mdio_dev = ocp_get_drvdata(mdiodev);
+ if (!dev->mdio_dev) {
+ printk(KERN_ERR
+ "emac%d: emac%d hasn't been initialized yet!\n",
+ dev->def->index, emacdata->mdio_idx);
+ err = -ENODEV;
+ goto out2;
+ }
}
- /* Check if we need to attach to a TAH */
- if (emacdata->tah_idx >= 0) {
- ep->tah_dev =
- ocp_find_device(OCP_ANY_ID, OCP_FUNC_TAH,
- emacdata->tah_idx);
- if (ep->tah_dev == NULL)
- printk(KERN_WARNING
- "emac%d: TAH %d requested but not found !\n",
- ocpdev->def->index, emacdata->tah_idx);
- else if ((rc = emac_init_tah(ep)) != 0)
- goto bail;
+ /* Attach to ZMII, if needed */
+ if ((err = zmii_attach(dev)) != 0)
+ goto out2;
+
+ /* Attach to RGMII, if needed */
+ if ((err = rgmii_attach(dev)) != 0)
+ goto out3;
+
+ /* Attach to TAH, if needed */
+ if ((err = tah_attach(dev)) != 0)
+ goto out4;
+
+ /* Map EMAC regs */
+ dev->emacp =
+ (struct emac_regs *)ioremap(dev->def->paddr,
+ sizeof(struct emac_regs));
+ if (!dev->emacp) {
+ printk(KERN_ERR "emac%d: could not ioremap device registers!\n",
+ dev->def->index);
+ err = -ENOMEM;
+ goto out5;
}
- if (deferred_init) {
- if (!list_empty(&emac_init_list)) {
- struct list_head *entry;
- struct emac_def_dev *ddev;
+ /* Fill in MAC address */
+ for (i = 0; i < 6; ++i)
+ ndev->dev_addr[i] = emacdata->mac_addr[i];
- list_for_each(entry, &emac_init_list) {
- ddev =
- list_entry(entry, struct emac_def_dev,
- link);
- emac_init_device(ddev->ocpdev, ddev->mal);
- }
+ /* Set some link defaults before we can find out real parameters */
+ dev->phy.speed = SPEED_100;
+ dev->phy.duplex = DUPLEX_FULL;
+ dev->phy.autoneg = AUTONEG_DISABLE;
+ dev->phy.pause = dev->phy.asym_pause = 0;
+ init_timer(&dev->link_timer);
+ dev->link_timer.function = emac_link_timer;
+ dev->link_timer.data = (unsigned long)dev;
+
+ /* Find PHY if any */
+ dev->phy.dev = ndev;
+ dev->phy.mode = emacdata->phy_mode;
+ if (emacdata->phy_map != 0xffffffff) {
+ u32 phy_map = emacdata->phy_map | busy_phy_map;
+ u32 adv;
+
+ DBG("%d: PHY maps %08x %08x" NL, dev->def->index,
+ emacdata->phy_map, busy_phy_map);
+
+ EMAC_RX_CLK_TX(dev->def->index);
+
+ dev->phy.mdio_read = emac_mdio_read;
+ dev->phy.mdio_write = emac_mdio_write;
+
+ /* Configure EMAC with defaults so we can at least use MDIO
+ * This is needed mostly for 440GX
+ */
+ if (emac_phy_gpcs(dev->phy.mode)) {
+ /* XXX
+ * Make GPCS PHY address equal to EMAC index.
+ * We probably should take into account busy_phy_map
+ * and/or phy_map here.
+ */
+ dev->phy.address = dev->def->index;
}
- }
+
+ emac_configure(dev);
+
+ for (i = 0; i < 0x20; phy_map >>= 1, ++i)
+ if (!(phy_map & 1)) {
+ int r;
+ busy_phy_map |= 1 << i;
- /* Init link monitoring timer */
- init_timer(&ep->link_timer);
- ep->link_timer.function = emac_link_timer;
- ep->link_timer.data = (unsigned long)ep;
- ep->timer_ticks = 0;
-
- /* Fill up the mii_phy structure */
- ep->phy_mii.dev = ndev;
- ep->phy_mii.mdio_read = emac_phy_read;
- ep->phy_mii.mdio_write = emac_phy_write;
- ep->phy_mii.mode = emacdata->phy_mode;
-
- /* Find PHY */
- phy_map = emacdata->phy_map | busy_phy_map;
- for (i = 0; i <= 0x1f; i++, phy_map >>= 1) {
- if ((phy_map & 0x1) == 0) {
- int val = emac_phy_read(ndev, i, MII_BMCR);
- if (val != 0xffff && val != -1)
- break;
+ /* Quick check if there is a PHY at the address */
+ r = emac_mdio_read(dev->ndev, i, MII_BMCR);
+ if (r == 0xffff || r < 0)
+ continue;
+ if (!mii_phy_probe(&dev->phy, i))
+ break;
+ }
+ if (i == 0x20) {
+ printk(KERN_WARNING "emac%d: can't find PHY!\n",
+ dev->def->index);
+ goto out6;
}
- }
- if (i == 0x20) {
- printk(KERN_WARNING "emac%d: Can't find PHY.\n",
- ocpdev->def->index);
- rc = -ENODEV;
- goto bail;
- }
- busy_phy_map |= 1 << i;
- ep->mii_phy_addr = i;
- rc = mii_phy_probe(&ep->phy_mii, i);
- if (rc) {
- printk(KERN_WARNING "emac%d: Failed to probe PHY type.\n",
- ocpdev->def->index);
- rc = -ENODEV;
- goto bail;
- }
-
- /* Disable any PHY features not supported by the platform */
- ep->phy_mii.def->features &= ~emacdata->phy_feat_exc;
- /* Setup initial PHY config & startup aneg */
- if (ep->phy_mii.def->ops->init)
- ep->phy_mii.def->ops->init(&ep->phy_mii);
- netif_carrier_off(ndev);
- if (ep->phy_mii.def->features & SUPPORTED_Autoneg)
- ep->want_autoneg = 1;
- else {
- ep->want_autoneg = 0;
+ /* Init PHY */
+ if (dev->phy.def->ops->init)
+ dev->phy.def->ops->init(&dev->phy);
- /* Select highest supported speed/duplex */
- if (ep->phy_mii.def->features & SUPPORTED_1000baseT_Full) {
- ep->phy_mii.speed = SPEED_1000;
- ep->phy_mii.duplex = DUPLEX_FULL;
- } else if (ep->phy_mii.def->features &
- SUPPORTED_1000baseT_Half) {
- ep->phy_mii.speed = SPEED_1000;
- ep->phy_mii.duplex = DUPLEX_HALF;
- } else if (ep->phy_mii.def->features &
- SUPPORTED_100baseT_Full) {
- ep->phy_mii.speed = SPEED_100;
- ep->phy_mii.duplex = DUPLEX_FULL;
- } else if (ep->phy_mii.def->features &
- SUPPORTED_100baseT_Half) {
- ep->phy_mii.speed = SPEED_100;
- ep->phy_mii.duplex = DUPLEX_HALF;
- } else if (ep->phy_mii.def->features &
- SUPPORTED_10baseT_Full) {
- ep->phy_mii.speed = SPEED_10;
- ep->phy_mii.duplex = DUPLEX_FULL;
+ /* Disable any PHY features not supported by the platform */
+ dev->phy.def->features &= ~emacdata->phy_feat_exc;
+
+ /* Setup initial link parameters */
+ if (dev->phy.features & SUPPORTED_Autoneg) {
+ adv = dev->phy.features;
+#if !defined(CONFIG_40x)
+ adv |= ADVERTISED_Pause | ADVERTISED_Asym_Pause;
+#endif
+ /* Restart autonegotiation */
+ dev->phy.def->ops->setup_aneg(&dev->phy, adv);
} else {
- ep->phy_mii.speed = SPEED_10;
- ep->phy_mii.duplex = DUPLEX_HALF;
+ u32 f = dev->phy.def->features;
+ int speed = SPEED_10, fd = DUPLEX_HALF;
+
+ /* Select highest supported speed/duplex */
+ if (f & SUPPORTED_1000baseT_Full) {
+ speed = SPEED_1000;
+ fd = DUPLEX_FULL;
+ } else if (f & SUPPORTED_1000baseT_Half)
+ speed = SPEED_1000;
+ else if (f & SUPPORTED_100baseT_Full) {
+ speed = SPEED_100;
+ fd = DUPLEX_FULL;
+ } else if (f & SUPPORTED_100baseT_Half)
+ speed = SPEED_100;
+ else if (f & SUPPORTED_10baseT_Full)
+ fd = DUPLEX_FULL;
+
+ /* Force link parameters */
+ dev->phy.def->ops->setup_forced(&dev->phy, speed, fd);
}
- }
- emac_start_link(ep, NULL);
+ } else {
+ emac_reset(dev);
- /* read the MAC Address */
- for (i = 0; i < 6; i++)
- ndev->dev_addr[i] = emacdata->mac_addr[i];
+ /* PHY-less configuration.
+ * XXX I probably should move these settings to emacdata
+ */
+ dev->phy.address = -1;
+ dev->phy.features = SUPPORTED_100baseT_Full | SUPPORTED_MII;
+ dev->phy.pause = 1;
+ }
/* Fill in the driver function table */
ndev->open = &emac_open;
- ndev->hard_start_xmit = &emac_start_xmit;
+ if (dev->tah_dev) {
+ ndev->hard_start_xmit = &emac_start_xmit_sg;
+ ndev->features |= NETIF_F_IP_CSUM | NETIF_F_SG;
+ } else
+ ndev->hard_start_xmit = &emac_start_xmit;
+ ndev->tx_timeout = &emac_full_tx_reset;
+ ndev->watchdog_timeo = 5 * HZ;
ndev->stop = &emac_close;
ndev->get_stats = &emac_stats;
- if (emacdata->jumbo)
- ndev->change_mtu = &emac_change_mtu;
- ndev->set_mac_address = &emac_set_mac_address;
ndev->set_multicast_list = &emac_set_multicast_list;
ndev->do_ioctl = &emac_ioctl;
+ if (emac_phy_supports_gige(emacdata->phy_mode)) {
+ ndev->change_mtu = &emac_change_mtu;
+ dev->commac.ops = &emac_commac_sg_ops;
+ }
SET_ETHTOOL_OPS(ndev, &emac_ethtool_ops);
- if (emacdata->tah_idx >= 0)
- ndev->features = NETIF_F_IP_CSUM | NETIF_F_SG;
-#ifdef CONFIG_NET_POLL_CONTROLLER
- ndev->poll_controller = emac_netpoll;
-#endif
- SET_MODULE_OWNER(ndev);
+ netif_carrier_off(ndev);
+ netif_stop_queue(ndev);
+
+ err = register_netdev(ndev);
+ if (err) {
+ printk(KERN_ERR "emac%d: failed to register net device (%d)!\n",
+ dev->def->index, err);
+ goto out6;
+ }
- rc = register_netdev(ndev);
- if (rc != 0)
- goto bail;
+ ocp_set_drvdata(ocpdev, dev);
- printk("%s: IBM emac, MAC %02x:%02x:%02x:%02x:%02x:%02x\n",
- ndev->name,
+ printk("%s: emac%d, MAC %02x:%02x:%02x:%02x:%02x:%02x\n",
+ ndev->name, dev->def->index,
ndev->dev_addr[0], ndev->dev_addr[1], ndev->dev_addr[2],
ndev->dev_addr[3], ndev->dev_addr[4], ndev->dev_addr[5]);
- printk(KERN_INFO "%s: Found %s PHY (0x%02x)\n",
- ndev->name, ep->phy_mii.def->name, ep->mii_phy_addr);
-
- bail:
- if (rc && commac_reg)
- mal_unregister_commac(ep->mal, &ep->commac);
- if (rc && ndev)
- kfree(ndev);
-
- return rc;
-}
-
-static int emac_probe(struct ocp_device *ocpdev)
-{
- struct ocp_device *maldev;
- struct ibm_ocp_mal *mal;
- struct ocp_func_emac_data *emacdata;
-
- emacdata = (struct ocp_func_emac_data *)ocpdev->def->additions;
- if (emacdata == NULL) {
- printk(KERN_ERR "emac%d: Missing additional datas !\n",
- ocpdev->def->index);
- return -ENODEV;
- }
- /* Get the MAL device */
- maldev = ocp_find_device(OCP_ANY_ID, OCP_FUNC_MAL, emacdata->mal_idx);
- if (maldev == NULL) {
- printk("No maldev\n");
- return -ENODEV;
- }
- /*
- * Get MAL driver data, it must be here due to link order.
- * When the driver is modularized, symbol dependencies will
- * ensure the MAL driver is already present if built as a
- * module.
- */
- mal = (struct ibm_ocp_mal *)ocp_get_drvdata(maldev);
- if (mal == NULL) {
- printk("No maldrv\n");
- return -ENODEV;
- }
+ if (dev->phy.address >= 0)
+ printk("%s: found %s PHY (0x%02x)\n", ndev->name,
+ dev->phy.def->name, dev->phy.address);
- /* If we depend on another EMAC for MDIO, wait for it to show up */
- if (emacdata->mdio_idx >= 0 &&
- (emacdata->mdio_idx != ocpdev->def->index) && !mdio_ndev) {
- struct emac_def_dev *ddev;
- /* Add this index to the deferred init table */
- ddev = kmalloc(sizeof(struct emac_def_dev), GFP_KERNEL);
- ddev->ocpdev = ocpdev;
- ddev->mal = mal;
- list_add_tail(&ddev->link, &emac_init_list);
- } else {
- emac_init_device(ocpdev, mal);
- }
+ emac_dbg_register(dev->def->index, dev);
return 0;
+ out6:
+ iounmap((void *)dev->emacp);
+ out5:
+ tah_fini(dev->tah_dev);
+ out4:
+ rgmii_fini(dev->rgmii_dev, dev->rgmii_input);
+ out3:
+ zmii_fini(dev->zmii_dev, dev->zmii_input);
+ out2:
+ mal_unregister_commac(dev->mal, &dev->commac);
+ out:
+ kfree(ndev);
+ return err;
}
-/* Structure for a device driver */
static struct ocp_device_id emac_ids[] = {
- {.vendor = OCP_ANY_ID,.function = OCP_FUNC_EMAC},
- {.vendor = OCP_VENDOR_INVALID}
+ { .vendor = OCP_VENDOR_IBM, .function = OCP_FUNC_EMAC },
+ { .vendor = OCP_VENDOR_INVALID}
};
static struct ocp_driver emac_driver = {
.name = "emac",
.id_table = emac_ids,
-
.probe = emac_probe,
.remove = emac_remove,
};
static int __init emac_init(void)
{
- printk(KERN_INFO DRV_NAME ": " DRV_DESC ", version " DRV_VERSION "\n");
- printk(KERN_INFO "Maintained by " DRV_AUTHOR "\n");
+ printk(KERN_INFO DRV_DESC ", version " DRV_VERSION "\n");
+
+ DBG(": init" NL);
- if (skb_res > 2) {
- printk(KERN_WARNING "Invalid skb_res: %d, cropping to 2\n",
- skb_res);
- skb_res = 2;
+ if (mal_init())
+ return -ENODEV;
+
+ EMAC_CLK_INTERNAL;
+ if (ocp_register_driver(&emac_driver)) {
+ EMAC_CLK_EXTERNAL;
+ ocp_unregister_driver(&emac_driver);
+ mal_exit();
+ return -ENODEV;
}
+ EMAC_CLK_EXTERNAL;
- return ocp_register_driver(&emac_driver);
+ emac_init_debug();
+ return 0;
}
static void __exit emac_exit(void)
{
+ DBG(": exit" NL);
ocp_unregister_driver(&emac_driver);
+ mal_exit();
+ emac_fini_debug();
}
module_init(emac_init);
/*
- * ibm_emac_core.h
+ * drivers/net/ibm_emac/ibm_emac_core.h
*
- * Ethernet driver for the built in ethernet on the IBM 405 PowerPC
- * processor.
+ * Driver for PowerPC 4xx on-chip ethernet controller.
*
- * Armin Kuster akuster@mvista.com
- * Sept, 2001
+ * Copyright (c) 2004, 2005 Zultys Technologies.
+ * Eugene Surovegin <eugene.surovegin@zultys.com> or <ebs@ebshome.net>
*
- * Orignial driver
- * Johnnie Peters
- * jpeters@mvista.com
- *
- * Copyright 2000 MontaVista Softare Inc.
+ * Based on original work by
+ * Armin Kuster <akuster@mvista.com>
+ * Johnnie Peters <jpeters@mvista.com>
+ * Copyright 2000, 2001 MontaVista Softare Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
+ *
*/
+#ifndef __IBM_EMAC_CORE_H_
+#define __IBM_EMAC_CORE_H_
-#ifndef _IBM_EMAC_CORE_H_
-#define _IBM_EMAC_CORE_H_
-
+#include <linux/config.h>
#include <linux/netdevice.h>
+#include <linux/dma-mapping.h>
#include <asm/ocp.h>
-#include <asm/mmu.h> /* For phys_addr_t */
#include "ibm_emac.h"
#include "ibm_emac_phy.h"
-#include "ibm_emac_rgmii.h"
#include "ibm_emac_zmii.h"
+#include "ibm_emac_rgmii.h"
#include "ibm_emac_mal.h"
#include "ibm_emac_tah.h"
-#ifndef CONFIG_IBM_EMAC_TXB
-#define NUM_TX_BUFF 64
-#define NUM_RX_BUFF 64
-#else
-#define NUM_TX_BUFF CONFIG_IBM_EMAC_TXB
-#define NUM_RX_BUFF CONFIG_IBM_EMAC_RXB
-#endif
+#define NUM_TX_BUFF CONFIG_IBM_EMAC_TXB
+#define NUM_RX_BUFF CONFIG_IBM_EMAC_RXB
-/* This does 16 byte alignment, exactly what we need.
- * The packet length includes FCS, but we don't want to
- * include that when passing upstream as it messes up
- * bridging applications.
- */
-#ifndef CONFIG_IBM_EMAC_SKBRES
-#define SKB_RES 2
-#else
-#define SKB_RES CONFIG_IBM_EMAC_SKBRES
+/* Simple sanity check */
+#if NUM_TX_BUFF > 256 || NUM_RX_BUFF > 256
+#error Invalid number of buffer descriptors (greater than 256)
#endif
-/* Note about alignement. alloc_skb() returns a cache line
- * aligned buffer. However, dev_alloc_skb() will add 16 more
- * bytes and "reserve" them, so our buffer will actually end
- * on a half cache line. What we do is to use directly
- * alloc_skb, allocate 16 more bytes to match the total amount
- * allocated by dev_alloc_skb(), but we don't reserve.
+// XXX
+#define EMAC_MIN_MTU 46
+#define EMAC_MAX_MTU 9000
+
+/* Maximum L2 header length (VLAN tagged, no FCS) */
+#define EMAC_MTU_OVERHEAD (6 * 2 + 2 + 4)
+
+/* RX BD size for the given MTU */
+static inline int emac_rx_size(int mtu)
+{
+ if (mtu > ETH_DATA_LEN)
+ return MAL_MAX_RX_SIZE;
+ else
+ return mal_rx_size(ETH_DATA_LEN + EMAC_MTU_OVERHEAD);
+}
+
+#define EMAC_DMA_ALIGN(x) ALIGN((x), dma_get_cache_alignment())
+
+#define EMAC_RX_SKB_HEADROOM \
+ EMAC_DMA_ALIGN(CONFIG_IBM_EMAC_RX_SKB_HEADROOM)
+
+/* Size of RX skb for the given MTU */
+static inline int emac_rx_skb_size(int mtu)
+{
+ int size = max(mtu + EMAC_MTU_OVERHEAD, emac_rx_size(mtu));
+ return EMAC_DMA_ALIGN(size + 2) + EMAC_RX_SKB_HEADROOM;
+}
+
+/* RX DMA sync size */
+static inline int emac_rx_sync_size(int mtu)
+{
+ return EMAC_DMA_ALIGN(emac_rx_size(mtu) + 2);
+}
+
+/* Driver statistcs is split into two parts to make it more cache friendly:
+ * - normal statistics (packet count, etc)
+ * - error statistics
+ *
+ * When statistics is requested by ethtool, these parts are concatenated,
+ * normal one goes first.
+ *
+ * Please, keep these structures in sync with emac_stats_keys.
*/
-#define MAX_NUM_BUF_DESC 255
-#define DESC_BUF_SIZE 4080 /* max 4096-16 */
-#define DESC_BUF_SIZE_REG (DESC_BUF_SIZE / 16)
-
-/* Transmitter timeout. */
-#define TX_TIMEOUT (2*HZ)
-
-/* MDIO latency delay */
-#define MDIO_DELAY 250
-
-/* Power managment shift registers */
-#define IBM_CPM_EMMII 0 /* Shift value for MII */
-#define IBM_CPM_EMRX 1 /* Shift value for recv */
-#define IBM_CPM_EMTX 2 /* Shift value for MAC */
-#define IBM_CPM_EMAC(x) (((x)>>IBM_CPM_EMMII) | ((x)>>IBM_CPM_EMRX) | ((x)>>IBM_CPM_EMTX))
-
-#define ENET_HEADER_SIZE 14
-#define ENET_FCS_SIZE 4
-#define ENET_DEF_MTU_SIZE 1500
-#define ENET_DEF_BUF_SIZE (ENET_DEF_MTU_SIZE + ENET_HEADER_SIZE + ENET_FCS_SIZE)
-#define EMAC_MIN_FRAME 64
-#define EMAC_MAX_FRAME 9018
-#define EMAC_MIN_MTU (EMAC_MIN_FRAME - ENET_HEADER_SIZE - ENET_FCS_SIZE)
-#define EMAC_MAX_MTU (EMAC_MAX_FRAME - ENET_HEADER_SIZE - ENET_FCS_SIZE)
-
-#ifdef CONFIG_IBM_EMAC_ERRMSG
-void emac_serr_dump_0(struct net_device *dev);
-void emac_serr_dump_1(struct net_device *dev);
-void emac_err_dump(struct net_device *dev, int em0isr);
-void emac_phy_dump(struct net_device *);
-void emac_desc_dump(struct net_device *);
-void emac_mac_dump(struct net_device *);
-void emac_mal_dump(struct net_device *);
-#else
-#define emac_serr_dump_0(dev) do { } while (0)
-#define emac_serr_dump_1(dev) do { } while (0)
-#define emac_err_dump(dev,x) do { } while (0)
-#define emac_phy_dump(dev) do { } while (0)
-#define emac_desc_dump(dev) do { } while (0)
-#define emac_mac_dump(dev) do { } while (0)
-#define emac_mal_dump(dev) do { } while (0)
-#endif
+
+/* Normal TX/RX Statistics */
+struct ibm_emac_stats {
+ u64 rx_packets;
+ u64 rx_bytes;
+ u64 tx_packets;
+ u64 tx_bytes;
+ u64 rx_packets_csum;
+ u64 tx_packets_csum;
+};
+
+/* Error statistics */
+struct ibm_emac_error_stats {
+ u64 tx_undo;
+
+ /* Software RX Errors */
+ u64 rx_dropped_stack;
+ u64 rx_dropped_oom;
+ u64 rx_dropped_error;
+ u64 rx_dropped_resize;
+ u64 rx_dropped_mtu;
+ u64 rx_stopped;
+ /* BD reported RX errors */
+ u64 rx_bd_errors;
+ u64 rx_bd_overrun;
+ u64 rx_bd_bad_packet;
+ u64 rx_bd_runt_packet;
+ u64 rx_bd_short_event;
+ u64 rx_bd_alignment_error;
+ u64 rx_bd_bad_fcs;
+ u64 rx_bd_packet_too_long;
+ u64 rx_bd_out_of_range;
+ u64 rx_bd_in_range;
+ /* EMAC IRQ reported RX errors */
+ u64 rx_parity;
+ u64 rx_fifo_overrun;
+ u64 rx_overrun;
+ u64 rx_bad_packet;
+ u64 rx_runt_packet;
+ u64 rx_short_event;
+ u64 rx_alignment_error;
+ u64 rx_bad_fcs;
+ u64 rx_packet_too_long;
+ u64 rx_out_of_range;
+ u64 rx_in_range;
+
+ /* Software TX Errors */
+ u64 tx_dropped;
+ /* BD reported TX errors */
+ u64 tx_bd_errors;
+ u64 tx_bd_bad_fcs;
+ u64 tx_bd_carrier_loss;
+ u64 tx_bd_excessive_deferral;
+ u64 tx_bd_excessive_collisions;
+ u64 tx_bd_late_collision;
+ u64 tx_bd_multple_collisions;
+ u64 tx_bd_single_collision;
+ u64 tx_bd_underrun;
+ u64 tx_bd_sqe;
+ /* EMAC IRQ reported TX errors */
+ u64 tx_parity;
+ u64 tx_underrun;
+ u64 tx_sqe;
+ u64 tx_errors;
+};
+
+#define EMAC_ETHTOOL_STATS_COUNT ((sizeof(struct ibm_emac_stats) + \
+ sizeof(struct ibm_emac_error_stats)) \
+ / sizeof(u64))
struct ocp_enet_private {
- struct sk_buff *tx_skb[NUM_TX_BUFF];
- struct sk_buff *rx_skb[NUM_RX_BUFF];
- struct mal_descriptor *tx_desc;
- struct mal_descriptor *rx_desc;
- struct mal_descriptor *rx_dirty;
- struct net_device_stats stats;
- int tx_cnt;
- int rx_slot;
- int dirty_rx;
- int tx_slot;
- int ack_slot;
- int rx_buffer_size;
-
- struct mii_phy phy_mii;
- int mii_phy_addr;
- int want_autoneg;
- int timer_ticks;
- struct timer_list link_timer;
- struct net_device *mdio_dev;
-
- struct ocp_device *rgmii_dev;
- int rgmii_input;
-
- struct ocp_device *zmii_dev;
- int zmii_input;
-
- struct ibm_ocp_mal *mal;
- int mal_tx_chan, mal_rx_chan;
- struct mal_commac commac;
-
- struct ocp_device *tah_dev;
-
- int opened;
- int going_away;
- int wol_irq;
- emac_t *emacp;
- struct ocp_device *ocpdev;
- struct net_device *ndev;
- spinlock_t lock;
+ struct net_device *ndev; /* 0 */
+ struct emac_regs *emacp;
+
+ struct mal_descriptor *tx_desc;
+ int tx_cnt;
+ int tx_slot;
+ int ack_slot;
+
+ struct mal_descriptor *rx_desc;
+ int rx_slot;
+ struct sk_buff *rx_sg_skb; /* 1 */
+ int rx_skb_size;
+ int rx_sync_size;
+
+ struct ibm_emac_stats stats;
+ struct ocp_device *tah_dev;
+
+ struct ibm_ocp_mal *mal;
+ struct mal_commac commac;
+
+ struct sk_buff *tx_skb[NUM_TX_BUFF];
+ struct sk_buff *rx_skb[NUM_RX_BUFF];
+
+ struct ocp_device *zmii_dev;
+ int zmii_input;
+ struct ocp_enet_private *mdio_dev;
+ struct ocp_device *rgmii_dev;
+ int rgmii_input;
+
+ struct ocp_def *def;
+
+ struct mii_phy phy;
+ struct timer_list link_timer;
+ int reset_failed;
+
+ struct ibm_emac_error_stats estats;
+ struct net_device_stats nstats;
+
+ struct device* ldev;
};
-#endif /* _IBM_EMAC_CORE_H_ */
+
+/* Ethtool get_regs complex data.
+ * We want to get not just EMAC registers, but also MAL, ZMII, RGMII, TAH
+ * when available.
+ *
+ * Returned BLOB consists of the ibm_emac_ethtool_regs_hdr,
+ * MAL registers, EMAC registers and optional ZMII, RGMII, TAH registers.
+ * Each register component is preceded with emac_ethtool_regs_subhdr.
+ * Order of the optional headers follows their relative bit posititions
+ * in emac_ethtool_regs_hdr.components
+ */
+#define EMAC_ETHTOOL_REGS_ZMII 0x00000001
+#define EMAC_ETHTOOL_REGS_RGMII 0x00000002
+#define EMAC_ETHTOOL_REGS_TAH 0x00000004
+
+struct emac_ethtool_regs_hdr {
+ u32 components;
+};
+
+struct emac_ethtool_regs_subhdr {
+ u32 version;
+ u32 index;
+};
+
+#endif /* __IBM_EMAC_CORE_H_ */
/*
- * ibm_ocp_debug.c
+ * drivers/net/ibm_emac/ibm_emac_debug.c
*
- * This has all the debug routines that where in *_enet.c
+ * Driver for PowerPC 4xx on-chip ethernet controller, debug print routines.
*
- * Armin Kuster akuster@mvista.com
- * April , 2002
- *
- * Copyright 2002 MontaVista Softare Inc.
+ * Copyright (c) 2004, 2005 Zultys Technologies
+ * Eugene Surovegin <eugene.surovegin@zultys.com> or <ebs@ebshome.net>
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
+ *
*/
-
#include <linux/config.h>
+#include <linux/init.h>
+#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/netdevice.h>
+#include <linux/sysrq.h>
#include <asm/io.h>
-#include "ibm_ocp_mal.h"
-#include "ibm_ocp_zmii.h"
-#include "ibm_ocp_enet.h"
-extern int emac_phy_read(struct net_device *dev, int mii_id, int reg);
+#include "ibm_emac_core.h"
+
+static void emac_desc_dump(int idx, struct ocp_enet_private *p)
+{
+ int i;
+ printk("** EMAC%d TX BDs **\n"
+ " tx_cnt = %d tx_slot = %d ack_slot = %d\n",
+ idx, p->tx_cnt, p->tx_slot, p->ack_slot);
+ for (i = 0; i < NUM_TX_BUFF / 2; ++i)
+ printk
+ ("bd[%2d] 0x%08x %c 0x%04x %4u - bd[%2d] 0x%08x %c 0x%04x %4u\n",
+ i, p->tx_desc[i].data_ptr, p->tx_skb[i] ? 'V' : ' ',
+ p->tx_desc[i].ctrl, p->tx_desc[i].data_len,
+ NUM_TX_BUFF / 2 + i,
+ p->tx_desc[NUM_TX_BUFF / 2 + i].data_ptr,
+ p->tx_skb[NUM_TX_BUFF / 2 + i] ? 'V' : ' ',
+ p->tx_desc[NUM_TX_BUFF / 2 + i].ctrl,
+ p->tx_desc[NUM_TX_BUFF / 2 + i].data_len);
+
+ printk("** EMAC%d RX BDs **\n"
+ " rx_slot = %d rx_stopped = %d rx_skb_size = %d rx_sync_size = %d\n"
+ " rx_sg_skb = 0x%p\n",
+ idx, p->rx_slot, p->commac.rx_stopped, p->rx_skb_size,
+ p->rx_sync_size, p->rx_sg_skb);
+ for (i = 0; i < NUM_RX_BUFF / 2; ++i)
+ printk
+ ("bd[%2d] 0x%08x %c 0x%04x %4u - bd[%2d] 0x%08x %c 0x%04x %4u\n",
+ i, p->rx_desc[i].data_ptr, p->rx_skb[i] ? 'V' : ' ',
+ p->rx_desc[i].ctrl, p->rx_desc[i].data_len,
+ NUM_RX_BUFF / 2 + i,
+ p->rx_desc[NUM_RX_BUFF / 2 + i].data_ptr,
+ p->rx_skb[NUM_RX_BUFF / 2 + i] ? 'V' : ' ',
+ p->rx_desc[NUM_RX_BUFF / 2 + i].ctrl,
+ p->rx_desc[NUM_RX_BUFF / 2 + i].data_len);
+}
+
+static void emac_mac_dump(int idx, struct ocp_enet_private *dev)
+{
+ struct emac_regs *p = dev->emacp;
+
+ printk("** EMAC%d registers **\n"
+ "MR0 = 0x%08x MR1 = 0x%08x TMR0 = 0x%08x TMR1 = 0x%08x\n"
+ "RMR = 0x%08x ISR = 0x%08x ISER = 0x%08x\n"
+ "IAR = %04x%08x VTPID = 0x%04x VTCI = 0x%04x\n"
+ "IAHT: 0x%04x 0x%04x 0x%04x 0x%04x "
+ "GAHT: 0x%04x 0x%04x 0x%04x 0x%04x\n"
+ "LSA = %04x%08x IPGVR = 0x%04x\n"
+ "STACR = 0x%08x TRTR = 0x%08x RWMR = 0x%08x\n"
+ "OCTX = 0x%08x OCRX = 0x%08x IPCR = 0x%08x\n",
+ idx, in_be32(&p->mr0), in_be32(&p->mr1),
+ in_be32(&p->tmr0), in_be32(&p->tmr1),
+ in_be32(&p->rmr), in_be32(&p->isr), in_be32(&p->iser),
+ in_be32(&p->iahr), in_be32(&p->ialr), in_be32(&p->vtpid),
+ in_be32(&p->vtci),
+ in_be32(&p->iaht1), in_be32(&p->iaht2), in_be32(&p->iaht3),
+ in_be32(&p->iaht4),
+ in_be32(&p->gaht1), in_be32(&p->gaht2), in_be32(&p->gaht3),
+ in_be32(&p->gaht4),
+ in_be32(&p->lsah), in_be32(&p->lsal), in_be32(&p->ipgvr),
+ in_be32(&p->stacr), in_be32(&p->trtr), in_be32(&p->rwmr),
+ in_be32(&p->octx), in_be32(&p->ocrx), in_be32(&p->ipcr)
+ );
+
+ emac_desc_dump(idx, dev);
+}
+
+static void emac_mal_dump(struct ibm_ocp_mal *mal)
+{
+ struct ocp_func_mal_data *maldata = mal->def->additions;
+ int i;
+
+ printk("** MAL%d Registers **\n"
+ "CFG = 0x%08x ESR = 0x%08x IER = 0x%08x\n"
+ "TX|CASR = 0x%08x CARR = 0x%08x EOBISR = 0x%08x DEIR = 0x%08x\n"
+ "RX|CASR = 0x%08x CARR = 0x%08x EOBISR = 0x%08x DEIR = 0x%08x\n",
+ mal->def->index,
+ get_mal_dcrn(mal, MAL_CFG), get_mal_dcrn(mal, MAL_ESR),
+ get_mal_dcrn(mal, MAL_IER),
+ get_mal_dcrn(mal, MAL_TXCASR), get_mal_dcrn(mal, MAL_TXCARR),
+ get_mal_dcrn(mal, MAL_TXEOBISR), get_mal_dcrn(mal, MAL_TXDEIR),
+ get_mal_dcrn(mal, MAL_RXCASR), get_mal_dcrn(mal, MAL_RXCARR),
+ get_mal_dcrn(mal, MAL_RXEOBISR), get_mal_dcrn(mal, MAL_RXDEIR)
+ );
+
+ printk("TX|");
+ for (i = 0; i < maldata->num_tx_chans; ++i) {
+ if (i && !(i % 4))
+ printk("\n ");
+ printk("CTP%d = 0x%08x ", i, get_mal_dcrn(mal, MAL_TXCTPR(i)));
+ }
+ printk("\nRX|");
+ for (i = 0; i < maldata->num_rx_chans; ++i) {
+ if (i && !(i % 4))
+ printk("\n ");
+ printk("CTP%d = 0x%08x ", i, get_mal_dcrn(mal, MAL_RXCTPR(i)));
+ }
+ printk("\n ");
+ for (i = 0; i < maldata->num_rx_chans; ++i) {
+ u32 r = get_mal_dcrn(mal, MAL_RCBS(i));
+ if (i && !(i % 3))
+ printk("\n ");
+ printk("RCBS%d = 0x%08x (%d) ", i, r, r * 16);
+ }
+ printk("\n");
+}
+
+static struct ocp_enet_private *__emacs[4];
+static struct ibm_ocp_mal *__mals[1];
-void emac_phy_dump(struct net_device *dev)
+void emac_dbg_register(int idx, struct ocp_enet_private *dev)
{
- struct ocp_enet_private *fep = dev->priv;
- unsigned long i;
- uint data;
-
- printk(KERN_DEBUG " Prepare for Phy dump....\n");
- for (i = 0; i < 0x1A; i++) {
- data = emac_phy_read(dev, fep->mii_phy_addr, i);
- printk(KERN_DEBUG "Phy reg 0x%lx ==> %4x\n", i, data);
- if (i == 0x07)
- i = 0x0f;
+ unsigned long flags;
+
+ if (idx >= sizeof(__emacs) / sizeof(__emacs[0])) {
+ printk(KERN_WARNING
+ "invalid index %d when registering EMAC for debugging\n",
+ idx);
+ return;
}
+
+ local_irq_save(flags);
+ __emacs[idx] = dev;
+ local_irq_restore(flags);
}
-void emac_desc_dump(struct net_device *dev)
+void mal_dbg_register(int idx, struct ibm_ocp_mal *mal)
{
- struct ocp_enet_private *fep = dev->priv;
- int curr_slot;
-
- printk(KERN_DEBUG
- "dumping the receive descriptors: current slot is %d\n",
- fep->rx_slot);
- for (curr_slot = 0; curr_slot < NUM_RX_BUFF; curr_slot++) {
- printk(KERN_DEBUG
- "Desc %02d: status 0x%04x, length %3d, addr 0x%x\n",
- curr_slot, fep->rx_desc[curr_slot].ctrl,
- fep->rx_desc[curr_slot].data_len,
- (unsigned int)fep->rx_desc[curr_slot].data_ptr);
+ unsigned long flags;
+
+ if (idx >= sizeof(__mals) / sizeof(__mals[0])) {
+ printk(KERN_WARNING
+ "invalid index %d when registering MAL for debugging\n",
+ idx);
+ return;
}
+
+ local_irq_save(flags);
+ __mals[idx] = mal;
+ local_irq_restore(flags);
}
-void emac_mac_dump(struct net_device *dev)
+void emac_dbg_dump_all(void)
{
- struct ocp_enet_private *fep = dev->priv;
- volatile emac_t *emacp = fep->emacp;
-
- printk(KERN_DEBUG "EMAC DEBUG ********** \n");
- printk(KERN_DEBUG "EMAC_M0 ==> 0x%x\n", in_be32(&emacp->em0mr0));
- printk(KERN_DEBUG "EMAC_M1 ==> 0x%x\n", in_be32(&emacp->em0mr1));
- printk(KERN_DEBUG "EMAC_TXM0==> 0x%x\n", in_be32(&emacp->em0tmr0));
- printk(KERN_DEBUG "EMAC_TXM1==> 0x%x\n", in_be32(&emacp->em0tmr1));
- printk(KERN_DEBUG "EMAC_RXM ==> 0x%x\n", in_be32(&emacp->em0rmr));
- printk(KERN_DEBUG "EMAC_ISR ==> 0x%x\n", in_be32(&emacp->em0isr));
- printk(KERN_DEBUG "EMAC_IER ==> 0x%x\n", in_be32(&emacp->em0iser));
- printk(KERN_DEBUG "EMAC_IAH ==> 0x%x\n", in_be32(&emacp->em0iahr));
- printk(KERN_DEBUG "EMAC_IAL ==> 0x%x\n", in_be32(&emacp->em0ialr));
- printk(KERN_DEBUG "EMAC_VLAN_TPID_REG ==> 0x%x\n",
- in_be32(&emacp->em0vtpid));
+ unsigned int i;
+ unsigned long flags;
+
+ local_irq_save(flags);
+
+ for (i = 0; i < sizeof(__mals) / sizeof(__mals[0]); ++i)
+ if (__mals[i])
+ emac_mal_dump(__mals[i]);
+
+ for (i = 0; i < sizeof(__emacs) / sizeof(__emacs[0]); ++i)
+ if (__emacs[i])
+ emac_mac_dump(i, __emacs[i]);
+
+ local_irq_restore(flags);
}
-void emac_mal_dump(struct net_device *dev)
+#if defined(CONFIG_MAGIC_SYSRQ)
+static void emac_sysrq_handler(int key, struct pt_regs *pt_regs,
+ struct tty_struct *tty)
{
- struct ibm_ocp_mal *mal = ((struct ocp_enet_private *)dev->priv)->mal;
-
- printk(KERN_DEBUG " MAL DEBUG ********** \n");
- printk(KERN_DEBUG " MCR ==> 0x%x\n",
- (unsigned int)get_mal_dcrn(mal, DCRN_MALCR));
- printk(KERN_DEBUG " ESR ==> 0x%x\n",
- (unsigned int)get_mal_dcrn(mal, DCRN_MALESR));
- printk(KERN_DEBUG " IER ==> 0x%x\n",
- (unsigned int)get_mal_dcrn(mal, DCRN_MALIER));
-#ifdef CONFIG_40x
- printk(KERN_DEBUG " DBR ==> 0x%x\n",
- (unsigned int)get_mal_dcrn(mal, DCRN_MALDBR));
-#endif /* CONFIG_40x */
- printk(KERN_DEBUG " TXCASR ==> 0x%x\n",
- (unsigned int)get_mal_dcrn(mal, DCRN_MALTXCASR));
- printk(KERN_DEBUG " TXCARR ==> 0x%x\n",
- (unsigned int)get_mal_dcrn(mal, DCRN_MALTXCARR));
- printk(KERN_DEBUG " TXEOBISR ==> 0x%x\n",
- (unsigned int)get_mal_dcrn(mal, DCRN_MALTXEOBISR));
- printk(KERN_DEBUG " TXDEIR ==> 0x%x\n",
- (unsigned int)get_mal_dcrn(mal, DCRN_MALTXDEIR));
- printk(KERN_DEBUG " RXCASR ==> 0x%x\n",
- (unsigned int)get_mal_dcrn(mal, DCRN_MALRXCASR));
- printk(KERN_DEBUG " RXCARR ==> 0x%x\n",
- (unsigned int)get_mal_dcrn(mal, DCRN_MALRXCARR));
- printk(KERN_DEBUG " RXEOBISR ==> 0x%x\n",
- (unsigned int)get_mal_dcrn(mal, DCRN_MALRXEOBISR));
- printk(KERN_DEBUG " RXDEIR ==> 0x%x\n",
- (unsigned int)get_mal_dcrn(mal, DCRN_MALRXDEIR));
- printk(KERN_DEBUG " TXCTP0R ==> 0x%x\n",
- (unsigned int)get_mal_dcrn(mal, DCRN_MALTXCTP0R));
- printk(KERN_DEBUG " TXCTP1R ==> 0x%x\n",
- (unsigned int)get_mal_dcrn(mal, DCRN_MALTXCTP1R));
- printk(KERN_DEBUG " TXCTP2R ==> 0x%x\n",
- (unsigned int)get_mal_dcrn(mal, DCRN_MALTXCTP2R));
- printk(KERN_DEBUG " TXCTP3R ==> 0x%x\n",
- (unsigned int)get_mal_dcrn(mal, DCRN_MALTXCTP3R));
- printk(KERN_DEBUG " RXCTP0R ==> 0x%x\n",
- (unsigned int)get_mal_dcrn(mal, DCRN_MALRXCTP0R));
- printk(KERN_DEBUG " RXCTP1R ==> 0x%x\n",
- (unsigned int)get_mal_dcrn(mal, DCRN_MALRXCTP1R));
- printk(KERN_DEBUG " RCBS0 ==> 0x%x\n",
- (unsigned int)get_mal_dcrn(mal, DCRN_MALRCBS0));
- printk(KERN_DEBUG " RCBS1 ==> 0x%x\n",
- (unsigned int)get_mal_dcrn(mal, DCRN_MALRCBS1));
+ emac_dbg_dump_all();
}
-void emac_serr_dump_0(struct net_device *dev)
+static struct sysrq_key_op emac_sysrq_op = {
+ .handler = emac_sysrq_handler,
+ .help_msg = "emaC",
+ .action_msg = "Show EMAC(s) status",
+};
+
+int __init emac_init_debug(void)
{
- struct ibm_ocp_mal *mal = ((struct ocp_enet_private *)dev->priv)->mal;
- unsigned long int mal_error, plb_error, plb_addr;
-
- mal_error = get_mal_dcrn(mal, DCRN_MALESR);
- printk(KERN_DEBUG "ppc405_eth_serr: %s channel %ld \n",
- (mal_error & 0x40000000) ? "Receive" :
- "Transmit", (mal_error & 0x3e000000) >> 25);
- printk(KERN_DEBUG " ----- latched error -----\n");
- if (mal_error & MALESR_DE)
- printk(KERN_DEBUG " DE: descriptor error\n");
- if (mal_error & MALESR_OEN)
- printk(KERN_DEBUG " ONE: OPB non-fullword error\n");
- if (mal_error & MALESR_OTE)
- printk(KERN_DEBUG " OTE: OPB timeout error\n");
- if (mal_error & MALESR_OSE)
- printk(KERN_DEBUG " OSE: OPB slave error\n");
-
- if (mal_error & MALESR_PEIN) {
- plb_error = mfdcr(DCRN_PLB0_BESR);
- printk(KERN_DEBUG
- " PEIN: PLB error, PLB0_BESR is 0x%x\n",
- (unsigned int)plb_error);
- plb_addr = mfdcr(DCRN_PLB0_BEAR);
- printk(KERN_DEBUG
- " PEIN: PLB error, PLB0_BEAR is 0x%x\n",
- (unsigned int)plb_addr);
- }
+ return register_sysrq_key('c', &emac_sysrq_op);
}
-void emac_serr_dump_1(struct net_device *dev)
+void __exit emac_fini_debug(void)
{
- struct ibm_ocp_mal *mal = ((struct ocp_enet_private *)dev->priv)->mal;
- int mal_error = get_mal_dcrn(mal, DCRN_MALESR);
-
- printk(KERN_DEBUG " ----- cumulative errors -----\n");
- if (mal_error & MALESR_DEI)
- printk(KERN_DEBUG " DEI: descriptor error interrupt\n");
- if (mal_error & MALESR_ONEI)
- printk(KERN_DEBUG " OPB non-fullword error interrupt\n");
- if (mal_error & MALESR_OTEI)
- printk(KERN_DEBUG " OTEI: timeout error interrupt\n");
- if (mal_error & MALESR_OSEI)
- printk(KERN_DEBUG " OSEI: slave error interrupt\n");
- if (mal_error & MALESR_PBEI)
- printk(KERN_DEBUG " PBEI: PLB bus error interrupt\n");
+ unregister_sysrq_key('c', &emac_sysrq_op);
}
-void emac_err_dump(struct net_device *dev, int em0isr)
+#else
+int __init emac_init_debug(void)
+{
+ return 0;
+}
+void __exit emac_fini_debug(void)
{
- printk(KERN_DEBUG "%s: on-chip ethernet error:\n", dev->name);
-
- if (em0isr & EMAC_ISR_OVR)
- printk(KERN_DEBUG " OVR: overrun\n");
- if (em0isr & EMAC_ISR_PP)
- printk(KERN_DEBUG " PP: control pause packet\n");
- if (em0isr & EMAC_ISR_BP)
- printk(KERN_DEBUG " BP: packet error\n");
- if (em0isr & EMAC_ISR_RP)
- printk(KERN_DEBUG " RP: runt packet\n");
- if (em0isr & EMAC_ISR_SE)
- printk(KERN_DEBUG " SE: short event\n");
- if (em0isr & EMAC_ISR_ALE)
- printk(KERN_DEBUG " ALE: odd number of nibbles in packet\n");
- if (em0isr & EMAC_ISR_BFCS)
- printk(KERN_DEBUG " BFCS: bad FCS\n");
- if (em0isr & EMAC_ISR_PTLE)
- printk(KERN_DEBUG " PTLE: oversized packet\n");
- if (em0isr & EMAC_ISR_ORE)
- printk(KERN_DEBUG
- " ORE: packet length field > max allowed LLC\n");
- if (em0isr & EMAC_ISR_IRE)
- printk(KERN_DEBUG " IRE: In Range error\n");
- if (em0isr & EMAC_ISR_DBDM)
- printk(KERN_DEBUG " DBDM: xmit error or SQE\n");
- if (em0isr & EMAC_ISR_DB0)
- printk(KERN_DEBUG " DB0: xmit error or SQE on TX channel 0\n");
- if (em0isr & EMAC_ISR_SE0)
- printk(KERN_DEBUG
- " SE0: Signal Quality Error test failure from TX channel 0\n");
- if (em0isr & EMAC_ISR_TE0)
- printk(KERN_DEBUG " TE0: xmit channel 0 aborted\n");
- if (em0isr & EMAC_ISR_DB1)
- printk(KERN_DEBUG " DB1: xmit error or SQE on TX channel \n");
- if (em0isr & EMAC_ISR_SE1)
- printk(KERN_DEBUG
- " SE1: Signal Quality Error test failure from TX channel 1\n");
- if (em0isr & EMAC_ISR_TE1)
- printk(KERN_DEBUG " TE1: xmit channel 1 aborted\n");
- if (em0isr & EMAC_ISR_MOS)
- printk(KERN_DEBUG " MOS\n");
- if (em0isr & EMAC_ISR_MOF)
- printk(KERN_DEBUG " MOF\n");
-
- emac_mac_dump(dev);
- emac_mal_dump(dev);
}
+#endif /* CONFIG_MAGIC_SYSRQ */
--- /dev/null
+/*
+ * drivers/net/ibm_emac/ibm_ocp_debug.h
+ *
+ * Driver for PowerPC 4xx on-chip ethernet controller, debug print routines.
+ *
+ * Copyright (c) 2004, 2005 Zultys Technologies
+ * Eugene Surovegin <eugene.surovegin@zultys.com> or <ebs@ebshome.net>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ */
+#ifndef __IBM_EMAC_DEBUG_H_
+#define __IBM_EMAC_DEBUG_H_
+
+#include <linux/config.h>
+#include <linux/init.h>
+#include "ibm_emac_core.h"
+#include "ibm_emac_mal.h"
+
+#if defined(CONFIG_IBM_EMAC_DEBUG)
+void emac_dbg_register(int idx, struct ocp_enet_private *dev);
+void mal_dbg_register(int idx, struct ibm_ocp_mal *mal);
+int emac_init_debug(void) __init;
+void emac_fini_debug(void) __exit;
+void emac_dbg_dump_all(void);
+# define DBG_LEVEL 1
+#else
+# define emac_dbg_register(x,y) ((void)0)
+# define mal_dbg_register(x,y) ((void)0)
+# define emac_init_debug() ((void)0)
+# define emac_fini_debug() ((void)0)
+# define emac_dbg_dump_all() ((void)0)
+# define DBG_LEVEL 0
+#endif
+
+#if DBG_LEVEL > 0
+# define DBG(f,x...) printk("emac" f, ##x)
+# define MAL_DBG(f,x...) printk("mal" f, ##x)
+# define ZMII_DBG(f,x...) printk("zmii" f, ##x)
+# define RGMII_DBG(f,x...) printk("rgmii" f, ##x)
+# define NL "\n"
+#else
+# define DBG(f,x...) ((void)0)
+# define MAL_DBG(f,x...) ((void)0)
+# define ZMII_DBG(f,x...) ((void)0)
+# define RGMII_DBG(f,x...) ((void)0)
+#endif
+#if DBG_LEVEL > 1
+# define DBG2(f,x...) DBG(f, ##x)
+# define MAL_DBG2(f,x...) MAL_DBG(f, ##x)
+# define ZMII_DBG2(f,x...) ZMII_DBG(f, ##x)
+# define RGMII_DBG2(f,x...) RGMII_DBG(f, ##x)
+#else
+# define DBG2(f,x...) ((void)0)
+# define MAL_DBG2(f,x...) ((void)0)
+# define ZMII_DBG2(f,x...) ((void)0)
+# define RGMII_DBG2(f,x...) ((void)0)
+#endif
+
+#endif /* __IBM_EMAC_DEBUG_H_ */
/*
- * ibm_ocp_mal.c
+ * drivers/net/ibm_emac/ibm_emac_mal.c
*
- * Armin Kuster akuster@mvista.com
- * Juen, 2002
+ * Memory Access Layer (MAL) support
+ *
+ * Copyright (c) 2004, 2005 Zultys Technologies.
+ * Eugene Surovegin <eugene.surovegin@zultys.com> or <ebs@ebshome.net>
*
- * Copyright 2002 MontaVista Softare Inc.
+ * Based on original work by
+ * Benjamin Herrenschmidt <benh@kernel.crashing.org>,
+ * David Gibson <hermes@gibson.dropbear.id.au>,
+ *
+ * Armin Kuster <akuster@mvista.com>
+ * Copyright 2002 MontaVista Softare Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
+ *
*/
-
#include <linux/config.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/errno.h>
#include <linux/netdevice.h>
#include <linux/init.h>
+#include <linux/interrupt.h>
#include <linux/dma-mapping.h>
-#include <asm/io.h>
-#include <asm/irq.h>
#include <asm/ocp.h>
+#include "ibm_emac_core.h"
#include "ibm_emac_mal.h"
+#include "ibm_emac_debug.h"
-// Locking: Should we share a lock with the client ? The client could provide
-// a lock pointer (optionally) in the commac structure... I don't think this is
-// really necessary though
-
-/* This lock protects the commac list. On today UP implementations, it's
- * really only used as IRQ protection in mal_{register,unregister}_commac()
- */
-static DEFINE_RWLOCK(mal_list_lock);
-
-int mal_register_commac(struct ibm_ocp_mal *mal, struct mal_commac *commac)
+int __init mal_register_commac(struct ibm_ocp_mal *mal,
+ struct mal_commac *commac)
{
unsigned long flags;
+ local_irq_save(flags);
- write_lock_irqsave(&mal_list_lock, flags);
+ MAL_DBG("%d: reg(%08x, %08x)" NL, mal->def->index,
+ commac->tx_chan_mask, commac->rx_chan_mask);
- /* Don't let multiple commacs claim the same channel */
+ /* Don't let multiple commacs claim the same channel(s) */
if ((mal->tx_chan_mask & commac->tx_chan_mask) ||
(mal->rx_chan_mask & commac->rx_chan_mask)) {
- write_unlock_irqrestore(&mal_list_lock, flags);
+ local_irq_restore(flags);
+ printk(KERN_WARNING "mal%d: COMMAC channels conflict!\n",
+ mal->def->index);
return -EBUSY;
}
mal->tx_chan_mask |= commac->tx_chan_mask;
mal->rx_chan_mask |= commac->rx_chan_mask;
+ list_add(&commac->list, &mal->list);
- list_add(&commac->list, &mal->commac);
-
- write_unlock_irqrestore(&mal_list_lock, flags);
-
+ local_irq_restore(flags);
return 0;
}
-int mal_unregister_commac(struct ibm_ocp_mal *mal, struct mal_commac *commac)
+void __exit mal_unregister_commac(struct ibm_ocp_mal *mal,
+ struct mal_commac *commac)
{
unsigned long flags;
+ local_irq_save(flags);
- write_lock_irqsave(&mal_list_lock, flags);
+ MAL_DBG("%d: unreg(%08x, %08x)" NL, mal->def->index,
+ commac->tx_chan_mask, commac->rx_chan_mask);
mal->tx_chan_mask &= ~commac->tx_chan_mask;
mal->rx_chan_mask &= ~commac->rx_chan_mask;
-
list_del_init(&commac->list);
- write_unlock_irqrestore(&mal_list_lock, flags);
-
- return 0;
+ local_irq_restore(flags);
}
int mal_set_rcbs(struct ibm_ocp_mal *mal, int channel, unsigned long size)
{
- switch (channel) {
- case 0:
- set_mal_dcrn(mal, DCRN_MALRCBS0, size);
- break;
-#ifdef DCRN_MALRCBS1
- case 1:
- set_mal_dcrn(mal, DCRN_MALRCBS1, size);
- break;
-#endif
-#ifdef DCRN_MALRCBS2
- case 2:
- set_mal_dcrn(mal, DCRN_MALRCBS2, size);
- break;
-#endif
-#ifdef DCRN_MALRCBS3
- case 3:
- set_mal_dcrn(mal, DCRN_MALRCBS3, size);
- break;
-#endif
- default:
+ struct ocp_func_mal_data *maldata = mal->def->additions;
+ BUG_ON(channel < 0 || channel >= maldata->num_rx_chans ||
+ size > MAL_MAX_RX_SIZE);
+
+ MAL_DBG("%d: set_rbcs(%d, %lu)" NL, mal->def->index, channel, size);
+
+ if (size & 0xf) {
+ printk(KERN_WARNING
+ "mal%d: incorrect RX size %lu for the channel %d\n",
+ mal->def->index, size, channel);
return -EINVAL;
}
+ set_mal_dcrn(mal, MAL_RCBS(channel), size >> 4);
return 0;
}
-static irqreturn_t mal_serr(int irq, void *dev_instance, struct pt_regs *regs)
+int mal_tx_bd_offset(struct ibm_ocp_mal *mal, int channel)
{
- struct ibm_ocp_mal *mal = dev_instance;
- unsigned long mal_error;
+ struct ocp_func_mal_data *maldata = mal->def->additions;
+ BUG_ON(channel < 0 || channel >= maldata->num_tx_chans);
+ return channel * NUM_TX_BUFF;
+}
- /*
- * This SERR applies to one of the devices on the MAL, here we charge
- * it against the first EMAC registered for the MAL.
- */
+int mal_rx_bd_offset(struct ibm_ocp_mal *mal, int channel)
+{
+ struct ocp_func_mal_data *maldata = mal->def->additions;
+ BUG_ON(channel < 0 || channel >= maldata->num_rx_chans);
+ return maldata->num_tx_chans * NUM_TX_BUFF + channel * NUM_RX_BUFF;
+}
- mal_error = get_mal_dcrn(mal, DCRN_MALESR);
+void mal_enable_tx_channel(struct ibm_ocp_mal *mal, int channel)
+{
+ local_bh_disable();
+ MAL_DBG("%d: enable_tx(%d)" NL, mal->def->index, channel);
+ set_mal_dcrn(mal, MAL_TXCASR,
+ get_mal_dcrn(mal, MAL_TXCASR) | MAL_CHAN_MASK(channel));
+ local_bh_enable();
+}
- printk(KERN_ERR "%s: System Error (MALESR=%lx)\n",
- "MAL" /* FIXME: get the name right */ , mal_error);
+void mal_disable_tx_channel(struct ibm_ocp_mal *mal, int channel)
+{
+ set_mal_dcrn(mal, MAL_TXCARR, MAL_CHAN_MASK(channel));
+ MAL_DBG("%d: disable_tx(%d)" NL, mal->def->index, channel);
+}
- /* FIXME: decipher error */
- /* DIXME: distribute to commacs, if possible */
+void mal_enable_rx_channel(struct ibm_ocp_mal *mal, int channel)
+{
+ local_bh_disable();
+ MAL_DBG("%d: enable_rx(%d)" NL, mal->def->index, channel);
+ set_mal_dcrn(mal, MAL_RXCASR,
+ get_mal_dcrn(mal, MAL_RXCASR) | MAL_CHAN_MASK(channel));
+ local_bh_enable();
+}
- /* Clear the error status register */
- set_mal_dcrn(mal, DCRN_MALESR, mal_error);
+void mal_disable_rx_channel(struct ibm_ocp_mal *mal, int channel)
+{
+ set_mal_dcrn(mal, MAL_RXCARR, MAL_CHAN_MASK(channel));
+ MAL_DBG("%d: disable_rx(%d)" NL, mal->def->index, channel);
+}
- return IRQ_HANDLED;
+void mal_poll_add(struct ibm_ocp_mal *mal, struct mal_commac *commac)
+{
+ local_bh_disable();
+ MAL_DBG("%d: poll_add(%p)" NL, mal->def->index, commac);
+ list_add_tail(&commac->poll_list, &mal->poll_list);
+ local_bh_enable();
}
-static irqreturn_t mal_txeob(int irq, void *dev_instance, struct pt_regs *regs)
+void mal_poll_del(struct ibm_ocp_mal *mal, struct mal_commac *commac)
+{
+ local_bh_disable();
+ MAL_DBG("%d: poll_del(%p)" NL, mal->def->index, commac);
+ list_del(&commac->poll_list);
+ local_bh_enable();
+}
+
+/* synchronized by mal_poll() */
+static inline void mal_enable_eob_irq(struct ibm_ocp_mal *mal)
+{
+ MAL_DBG2("%d: enable_irq" NL, mal->def->index);
+ set_mal_dcrn(mal, MAL_CFG, get_mal_dcrn(mal, MAL_CFG) | MAL_CFG_EOPIE);
+}
+
+/* synchronized by __LINK_STATE_RX_SCHED bit in ndev->state */
+static inline void mal_disable_eob_irq(struct ibm_ocp_mal *mal)
+{
+ set_mal_dcrn(mal, MAL_CFG, get_mal_dcrn(mal, MAL_CFG) & ~MAL_CFG_EOPIE);
+ MAL_DBG2("%d: disable_irq" NL, mal->def->index);
+}
+
+static irqreturn_t mal_serr(int irq, void *dev_instance, struct pt_regs *regs)
{
struct ibm_ocp_mal *mal = dev_instance;
- struct list_head *l;
- unsigned long isr;
+ u32 esr = get_mal_dcrn(mal, MAL_ESR);
- isr = get_mal_dcrn(mal, DCRN_MALTXEOBISR);
- set_mal_dcrn(mal, DCRN_MALTXEOBISR, isr);
+ /* Clear the error status register */
+ set_mal_dcrn(mal, MAL_ESR, esr);
- read_lock(&mal_list_lock);
- list_for_each(l, &mal->commac) {
- struct mal_commac *mc = list_entry(l, struct mal_commac, list);
+ MAL_DBG("%d: SERR %08x" NL, mal->def->index, esr);
- if (isr & mc->tx_chan_mask) {
- mc->ops->txeob(mc->dev, isr & mc->tx_chan_mask);
+ if (esr & MAL_ESR_EVB) {
+ if (esr & MAL_ESR_DE) {
+ /* We ignore Descriptor error,
+ * TXDE or RXDE interrupt will be generated anyway.
+ */
+ return IRQ_HANDLED;
}
+
+ if (esr & MAL_ESR_PEIN) {
+ /* PLB error, it's probably buggy hardware or
+ * incorrect physical address in BD (i.e. bug)
+ */
+ if (net_ratelimit())
+ printk(KERN_ERR
+ "mal%d: system error, PLB (ESR = 0x%08x)\n",
+ mal->def->index, esr);
+ return IRQ_HANDLED;
+ }
+
+ /* OPB error, it's probably buggy hardware or incorrect EBC setup */
+ if (net_ratelimit())
+ printk(KERN_ERR
+ "mal%d: system error, OPB (ESR = 0x%08x)\n",
+ mal->def->index, esr);
}
- read_unlock(&mal_list_lock);
+ return IRQ_HANDLED;
+}
+
+static inline void mal_schedule_poll(struct ibm_ocp_mal *mal)
+{
+ if (likely(netif_rx_schedule_prep(&mal->poll_dev))) {
+ MAL_DBG2("%d: schedule_poll" NL, mal->def->index);
+ mal_disable_eob_irq(mal);
+ __netif_rx_schedule(&mal->poll_dev);
+ } else
+ MAL_DBG2("%d: already in poll" NL, mal->def->index);
+}
+static irqreturn_t mal_txeob(int irq, void *dev_instance, struct pt_regs *regs)
+{
+ struct ibm_ocp_mal *mal = dev_instance;
+ u32 r = get_mal_dcrn(mal, MAL_TXEOBISR);
+ MAL_DBG2("%d: txeob %08x" NL, mal->def->index, r);
+ mal_schedule_poll(mal);
+ set_mal_dcrn(mal, MAL_TXEOBISR, r);
return IRQ_HANDLED;
}
static irqreturn_t mal_rxeob(int irq, void *dev_instance, struct pt_regs *regs)
{
struct ibm_ocp_mal *mal = dev_instance;
- struct list_head *l;
- unsigned long isr;
+ u32 r = get_mal_dcrn(mal, MAL_RXEOBISR);
+ MAL_DBG2("%d: rxeob %08x" NL, mal->def->index, r);
+ mal_schedule_poll(mal);
+ set_mal_dcrn(mal, MAL_RXEOBISR, r);
+ return IRQ_HANDLED;
+}
- isr = get_mal_dcrn(mal, DCRN_MALRXEOBISR);
- set_mal_dcrn(mal, DCRN_MALRXEOBISR, isr);
+static irqreturn_t mal_txde(int irq, void *dev_instance, struct pt_regs *regs)
+{
+ struct ibm_ocp_mal *mal = dev_instance;
+ u32 deir = get_mal_dcrn(mal, MAL_TXDEIR);
+ set_mal_dcrn(mal, MAL_TXDEIR, deir);
- read_lock(&mal_list_lock);
- list_for_each(l, &mal->commac) {
- struct mal_commac *mc = list_entry(l, struct mal_commac, list);
+ MAL_DBG("%d: txde %08x" NL, mal->def->index, deir);
- if (isr & mc->rx_chan_mask) {
- mc->ops->rxeob(mc->dev, isr & mc->rx_chan_mask);
- }
- }
- read_unlock(&mal_list_lock);
+ if (net_ratelimit())
+ printk(KERN_ERR
+ "mal%d: TX descriptor error (TXDEIR = 0x%08x)\n",
+ mal->def->index, deir);
return IRQ_HANDLED;
}
-static irqreturn_t mal_txde(int irq, void *dev_instance, struct pt_regs *regs)
+static irqreturn_t mal_rxde(int irq, void *dev_instance, struct pt_regs *regs)
{
struct ibm_ocp_mal *mal = dev_instance;
struct list_head *l;
- unsigned long deir;
+ u32 deir = get_mal_dcrn(mal, MAL_RXDEIR);
- deir = get_mal_dcrn(mal, DCRN_MALTXDEIR);
+ MAL_DBG("%d: rxde %08x" NL, mal->def->index, deir);
- /* FIXME: print which MAL correctly */
- printk(KERN_WARNING "%s: Tx descriptor error (MALTXDEIR=%lx)\n",
- "MAL", deir);
-
- read_lock(&mal_list_lock);
- list_for_each(l, &mal->commac) {
+ list_for_each(l, &mal->list) {
struct mal_commac *mc = list_entry(l, struct mal_commac, list);
-
- if (deir & mc->tx_chan_mask) {
- mc->ops->txde(mc->dev, deir & mc->tx_chan_mask);
+ if (deir & mc->rx_chan_mask) {
+ mc->rx_stopped = 1;
+ mc->ops->rxde(mc->dev);
}
}
- read_unlock(&mal_list_lock);
+
+ mal_schedule_poll(mal);
+ set_mal_dcrn(mal, MAL_RXDEIR, deir);
return IRQ_HANDLED;
}
-/*
- * This interrupt should be very rare at best. This occurs when
- * the hardware has a problem with the receive descriptors. The manual
- * states that it occurs when the hardware cannot the receive descriptor
- * empty bit is not set. The recovery mechanism will be to
- * traverse through the descriptors, handle any that are marked to be
- * handled and reinitialize each along the way. At that point the driver
- * will be restarted.
- */
-static irqreturn_t mal_rxde(int irq, void *dev_instance, struct pt_regs *regs)
+static int mal_poll(struct net_device *ndev, int *budget)
{
- struct ibm_ocp_mal *mal = dev_instance;
+ struct ibm_ocp_mal *mal = ndev->priv;
struct list_head *l;
- unsigned long deir;
-
- deir = get_mal_dcrn(mal, DCRN_MALRXDEIR);
+ int rx_work_limit = min(ndev->quota, *budget), received = 0, done;
+
+ MAL_DBG2("%d: poll(%d) %d ->" NL, mal->def->index, *budget,
+ rx_work_limit);
+ again:
+ /* Process TX skbs */
+ list_for_each(l, &mal->poll_list) {
+ struct mal_commac *mc =
+ list_entry(l, struct mal_commac, poll_list);
+ mc->ops->poll_tx(mc->dev);
+ }
- /*
- * This really is needed. This case encountered in stress testing.
+ /* Process RX skbs.
+ * We _might_ need something more smart here to enforce polling fairness.
*/
- if (deir == 0)
- return IRQ_HANDLED;
-
- /* FIXME: print which MAL correctly */
- printk(KERN_WARNING "%s: Rx descriptor error (MALRXDEIR=%lx)\n",
- "MAL", deir);
-
- read_lock(&mal_list_lock);
- list_for_each(l, &mal->commac) {
- struct mal_commac *mc = list_entry(l, struct mal_commac, list);
+ list_for_each(l, &mal->poll_list) {
+ struct mal_commac *mc =
+ list_entry(l, struct mal_commac, poll_list);
+ int n = mc->ops->poll_rx(mc->dev, rx_work_limit);
+ if (n) {
+ received += n;
+ rx_work_limit -= n;
+ if (rx_work_limit <= 0) {
+ done = 0;
+ goto more_work; // XXX What if this is the last one ?
+ }
+ }
+ }
- if (deir & mc->rx_chan_mask) {
- mc->ops->rxde(mc->dev, deir & mc->rx_chan_mask);
+ /* We need to disable IRQs to protect from RXDE IRQ here */
+ local_irq_disable();
+ __netif_rx_complete(ndev);
+ mal_enable_eob_irq(mal);
+ local_irq_enable();
+
+ done = 1;
+
+ /* Check for "rotting" packet(s) */
+ list_for_each(l, &mal->poll_list) {
+ struct mal_commac *mc =
+ list_entry(l, struct mal_commac, poll_list);
+ if (unlikely(mc->ops->peek_rx(mc->dev) || mc->rx_stopped)) {
+ MAL_DBG2("%d: rotting packet" NL, mal->def->index);
+ if (netif_rx_reschedule(ndev, received))
+ mal_disable_eob_irq(mal);
+ else
+ MAL_DBG2("%d: already in poll list" NL,
+ mal->def->index);
+
+ if (rx_work_limit > 0)
+ goto again;
+ else
+ goto more_work;
}
+ mc->ops->poll_tx(mc->dev);
}
- read_unlock(&mal_list_lock);
- return IRQ_HANDLED;
+ more_work:
+ ndev->quota -= received;
+ *budget -= received;
+
+ MAL_DBG2("%d: poll() %d <- %d" NL, mal->def->index, *budget,
+ done ? 0 : 1);
+ return done ? 0 : 1;
+}
+
+static void mal_reset(struct ibm_ocp_mal *mal)
+{
+ int n = 10;
+ MAL_DBG("%d: reset" NL, mal->def->index);
+
+ set_mal_dcrn(mal, MAL_CFG, MAL_CFG_SR);
+
+ /* Wait for reset to complete (1 system clock) */
+ while ((get_mal_dcrn(mal, MAL_CFG) & MAL_CFG_SR) && n)
+ --n;
+
+ if (unlikely(!n))
+ printk(KERN_ERR "mal%d: reset timeout\n", mal->def->index);
+}
+
+int mal_get_regs_len(struct ibm_ocp_mal *mal)
+{
+ return sizeof(struct emac_ethtool_regs_subhdr) +
+ sizeof(struct ibm_mal_regs);
+}
+
+void *mal_dump_regs(struct ibm_ocp_mal *mal, void *buf)
+{
+ struct emac_ethtool_regs_subhdr *hdr = buf;
+ struct ibm_mal_regs *regs = (struct ibm_mal_regs *)(hdr + 1);
+ struct ocp_func_mal_data *maldata = mal->def->additions;
+ int i;
+
+ hdr->version = MAL_VERSION;
+ hdr->index = mal->def->index;
+
+ regs->tx_count = maldata->num_tx_chans;
+ regs->rx_count = maldata->num_rx_chans;
+
+ regs->cfg = get_mal_dcrn(mal, MAL_CFG);
+ regs->esr = get_mal_dcrn(mal, MAL_ESR);
+ regs->ier = get_mal_dcrn(mal, MAL_IER);
+ regs->tx_casr = get_mal_dcrn(mal, MAL_TXCASR);
+ regs->tx_carr = get_mal_dcrn(mal, MAL_TXCARR);
+ regs->tx_eobisr = get_mal_dcrn(mal, MAL_TXEOBISR);
+ regs->tx_deir = get_mal_dcrn(mal, MAL_TXDEIR);
+ regs->rx_casr = get_mal_dcrn(mal, MAL_RXCASR);
+ regs->rx_carr = get_mal_dcrn(mal, MAL_RXCARR);
+ regs->rx_eobisr = get_mal_dcrn(mal, MAL_RXEOBISR);
+ regs->rx_deir = get_mal_dcrn(mal, MAL_RXDEIR);
+
+ for (i = 0; i < regs->tx_count; ++i)
+ regs->tx_ctpr[i] = get_mal_dcrn(mal, MAL_TXCTPR(i));
+
+ for (i = 0; i < regs->rx_count; ++i) {
+ regs->rx_ctpr[i] = get_mal_dcrn(mal, MAL_RXCTPR(i));
+ regs->rcbs[i] = get_mal_dcrn(mal, MAL_RCBS(i));
+ }
+ return regs + 1;
}
static int __init mal_probe(struct ocp_device *ocpdev)
{
- struct ibm_ocp_mal *mal = NULL;
+ struct ibm_ocp_mal *mal;
struct ocp_func_mal_data *maldata;
- int err = 0;
+ int err = 0, i, bd_size;
+
+ MAL_DBG("%d: probe" NL, ocpdev->def->index);
- maldata = (struct ocp_func_mal_data *)ocpdev->def->additions;
+ maldata = ocpdev->def->additions;
if (maldata == NULL) {
- printk(KERN_ERR "mal%d: Missing additional datas !\n",
+ printk(KERN_ERR "mal%d: missing additional data!\n",
ocpdev->def->index);
return -ENODEV;
}
- mal = kmalloc(sizeof(struct ibm_ocp_mal), GFP_KERNEL);
- if (mal == NULL) {
+ mal = kzalloc(sizeof(struct ibm_ocp_mal), GFP_KERNEL);
+ if (!mal) {
printk(KERN_ERR
- "mal%d: Out of memory allocating MAL structure !\n",
+ "mal%d: out of memory allocating MAL structure!\n",
ocpdev->def->index);
return -ENOMEM;
}
- memset(mal, 0, sizeof(*mal));
-
- switch (ocpdev->def->index) {
- case 0:
- mal->dcrbase = DCRN_MAL_BASE;
- break;
-#ifdef DCRN_MAL1_BASE
- case 1:
- mal->dcrbase = DCRN_MAL1_BASE;
- break;
-#endif
- default:
- BUG();
- }
-
- /**************************/
+ mal->dcrbase = maldata->dcr_base;
+ mal->def = ocpdev->def;
- INIT_LIST_HEAD(&mal->commac);
+ INIT_LIST_HEAD(&mal->poll_list);
+ set_bit(__LINK_STATE_START, &mal->poll_dev.state);
+ mal->poll_dev.weight = CONFIG_IBM_EMAC_POLL_WEIGHT;
+ mal->poll_dev.poll = mal_poll;
+ mal->poll_dev.priv = mal;
+ atomic_set(&mal->poll_dev.refcnt, 1);
- set_mal_dcrn(mal, DCRN_MALRXCARR, 0xFFFFFFFF);
- set_mal_dcrn(mal, DCRN_MALTXCARR, 0xFFFFFFFF);
+ INIT_LIST_HEAD(&mal->list);
- set_mal_dcrn(mal, DCRN_MALCR, MALCR_MMSR); /* 384 */
- /* FIXME: Add delay */
+ /* Load power-on reset defaults */
+ mal_reset(mal);
/* Set the MAL configuration register */
- set_mal_dcrn(mal, DCRN_MALCR,
- MALCR_PLBB | MALCR_OPBBL | MALCR_LEA |
- MALCR_PLBLT_DEFAULT);
-
- /* It would be nice to allocate buffers separately for each
- * channel, but we can't because the channels share the upper
- * 13 bits of address lines. Each channels buffer must also
- * be 4k aligned, so we allocate 4k for each channel. This is
- * inefficient FIXME: do better, if possible */
- mal->tx_virt_addr = dma_alloc_coherent(&ocpdev->dev,
- MAL_DT_ALIGN *
- maldata->num_tx_chans,
- &mal->tx_phys_addr, GFP_KERNEL);
- if (mal->tx_virt_addr == NULL) {
+ set_mal_dcrn(mal, MAL_CFG, MAL_CFG_DEFAULT | MAL_CFG_PLBB |
+ MAL_CFG_OPBBL | MAL_CFG_LEA);
+
+ mal_enable_eob_irq(mal);
+
+ /* Allocate space for BD rings */
+ BUG_ON(maldata->num_tx_chans <= 0 || maldata->num_tx_chans > 32);
+ BUG_ON(maldata->num_rx_chans <= 0 || maldata->num_rx_chans > 32);
+ bd_size = sizeof(struct mal_descriptor) *
+ (NUM_TX_BUFF * maldata->num_tx_chans +
+ NUM_RX_BUFF * maldata->num_rx_chans);
+ mal->bd_virt =
+ dma_alloc_coherent(&ocpdev->dev, bd_size, &mal->bd_dma, GFP_KERNEL);
+
+ if (!mal->bd_virt) {
printk(KERN_ERR
- "mal%d: Out of memory allocating MAL descriptors !\n",
- ocpdev->def->index);
+ "mal%d: out of memory allocating RX/TX descriptors!\n",
+ mal->def->index);
err = -ENOMEM;
goto fail;
}
+ memset(mal->bd_virt, 0, bd_size);
- /* God, oh, god, I hate DCRs */
- set_mal_dcrn(mal, DCRN_MALTXCTP0R, mal->tx_phys_addr);
-#ifdef DCRN_MALTXCTP1R
- if (maldata->num_tx_chans > 1)
- set_mal_dcrn(mal, DCRN_MALTXCTP1R,
- mal->tx_phys_addr + MAL_DT_ALIGN);
-#endif /* DCRN_MALTXCTP1R */
-#ifdef DCRN_MALTXCTP2R
- if (maldata->num_tx_chans > 2)
- set_mal_dcrn(mal, DCRN_MALTXCTP2R,
- mal->tx_phys_addr + 2 * MAL_DT_ALIGN);
-#endif /* DCRN_MALTXCTP2R */
-#ifdef DCRN_MALTXCTP3R
- if (maldata->num_tx_chans > 3)
- set_mal_dcrn(mal, DCRN_MALTXCTP3R,
- mal->tx_phys_addr + 3 * MAL_DT_ALIGN);
-#endif /* DCRN_MALTXCTP3R */
-#ifdef DCRN_MALTXCTP4R
- if (maldata->num_tx_chans > 4)
- set_mal_dcrn(mal, DCRN_MALTXCTP4R,
- mal->tx_phys_addr + 4 * MAL_DT_ALIGN);
-#endif /* DCRN_MALTXCTP4R */
-#ifdef DCRN_MALTXCTP5R
- if (maldata->num_tx_chans > 5)
- set_mal_dcrn(mal, DCRN_MALTXCTP5R,
- mal->tx_phys_addr + 5 * MAL_DT_ALIGN);
-#endif /* DCRN_MALTXCTP5R */
-#ifdef DCRN_MALTXCTP6R
- if (maldata->num_tx_chans > 6)
- set_mal_dcrn(mal, DCRN_MALTXCTP6R,
- mal->tx_phys_addr + 6 * MAL_DT_ALIGN);
-#endif /* DCRN_MALTXCTP6R */
-#ifdef DCRN_MALTXCTP7R
- if (maldata->num_tx_chans > 7)
- set_mal_dcrn(mal, DCRN_MALTXCTP7R,
- mal->tx_phys_addr + 7 * MAL_DT_ALIGN);
-#endif /* DCRN_MALTXCTP7R */
-
- mal->rx_virt_addr = dma_alloc_coherent(&ocpdev->dev,
- MAL_DT_ALIGN *
- maldata->num_rx_chans,
- &mal->rx_phys_addr, GFP_KERNEL);
-
- set_mal_dcrn(mal, DCRN_MALRXCTP0R, mal->rx_phys_addr);
-#ifdef DCRN_MALRXCTP1R
- if (maldata->num_rx_chans > 1)
- set_mal_dcrn(mal, DCRN_MALRXCTP1R,
- mal->rx_phys_addr + MAL_DT_ALIGN);
-#endif /* DCRN_MALRXCTP1R */
-#ifdef DCRN_MALRXCTP2R
- if (maldata->num_rx_chans > 2)
- set_mal_dcrn(mal, DCRN_MALRXCTP2R,
- mal->rx_phys_addr + 2 * MAL_DT_ALIGN);
-#endif /* DCRN_MALRXCTP2R */
-#ifdef DCRN_MALRXCTP3R
- if (maldata->num_rx_chans > 3)
- set_mal_dcrn(mal, DCRN_MALRXCTP3R,
- mal->rx_phys_addr + 3 * MAL_DT_ALIGN);
-#endif /* DCRN_MALRXCTP3R */
+ for (i = 0; i < maldata->num_tx_chans; ++i)
+ set_mal_dcrn(mal, MAL_TXCTPR(i), mal->bd_dma +
+ sizeof(struct mal_descriptor) *
+ mal_tx_bd_offset(mal, i));
+
+ for (i = 0; i < maldata->num_rx_chans; ++i)
+ set_mal_dcrn(mal, MAL_RXCTPR(i), mal->bd_dma +
+ sizeof(struct mal_descriptor) *
+ mal_rx_bd_offset(mal, i));
err = request_irq(maldata->serr_irq, mal_serr, 0, "MAL SERR", mal);
if (err)
- goto fail;
- err = request_irq(maldata->txde_irq, mal_txde, 0, "MAL TX DE ", mal);
+ goto fail2;
+ err = request_irq(maldata->txde_irq, mal_txde, 0, "MAL TX DE", mal);
if (err)
- goto fail;
+ goto fail3;
err = request_irq(maldata->txeob_irq, mal_txeob, 0, "MAL TX EOB", mal);
if (err)
- goto fail;
+ goto fail4;
err = request_irq(maldata->rxde_irq, mal_rxde, 0, "MAL RX DE", mal);
if (err)
- goto fail;
+ goto fail5;
err = request_irq(maldata->rxeob_irq, mal_rxeob, 0, "MAL RX EOB", mal);
if (err)
- goto fail;
+ goto fail6;
- set_mal_dcrn(mal, DCRN_MALIER,
- MALIER_DE | MALIER_NE | MALIER_TE |
- MALIER_OPBE | MALIER_PLBE);
+ /* Enable all MAL SERR interrupt sources */
+ set_mal_dcrn(mal, MAL_IER, MAL_IER_EVENTS);
- /* Advertise me to the rest of the world */
+ /* Advertise this instance to the rest of the world */
ocp_set_drvdata(ocpdev, mal);
- printk(KERN_INFO "mal%d: Initialized, %d tx channels, %d rx channels\n",
- ocpdev->def->index, maldata->num_tx_chans,
- maldata->num_rx_chans);
+ mal_dbg_register(mal->def->index, mal);
+ printk(KERN_INFO "mal%d: initialized, %d TX channels, %d RX channels\n",
+ mal->def->index, maldata->num_tx_chans, maldata->num_rx_chans);
return 0;
+ fail6:
+ free_irq(maldata->rxde_irq, mal);
+ fail5:
+ free_irq(maldata->txeob_irq, mal);
+ fail4:
+ free_irq(maldata->txde_irq, mal);
+ fail3:
+ free_irq(maldata->serr_irq, mal);
+ fail2:
+ dma_free_coherent(&ocpdev->dev, bd_size, mal->bd_virt, mal->bd_dma);
fail:
- /* FIXME: dispose requested IRQs ! */
- if (err && mal)
- kfree(mal);
+ kfree(mal);
return err;
}
static void __exit mal_remove(struct ocp_device *ocpdev)
{
struct ibm_ocp_mal *mal = ocp_get_drvdata(ocpdev);
- struct ocp_func_mal_data *maldata = ocpdev->def->additions;
+ struct ocp_func_mal_data *maldata = mal->def->additions;
+
+ MAL_DBG("%d: remove" NL, mal->def->index);
- BUG_ON(!maldata);
+ /* Syncronize with scheduled polling,
+ stolen from net/core/dev.c:dev_close()
+ */
+ clear_bit(__LINK_STATE_START, &mal->poll_dev.state);
+ netif_poll_disable(&mal->poll_dev);
+
+ if (!list_empty(&mal->list)) {
+ /* This is *very* bad */
+ printk(KERN_EMERG
+ "mal%d: commac list is not empty on remove!\n",
+ mal->def->index);
+ }
ocp_set_drvdata(ocpdev, NULL);
- /* FIXME: shut down the MAL, deal with dependency with emac */
free_irq(maldata->serr_irq, mal);
free_irq(maldata->txde_irq, mal);
free_irq(maldata->txeob_irq, mal);
free_irq(maldata->rxde_irq, mal);
free_irq(maldata->rxeob_irq, mal);
- if (mal->tx_virt_addr)
- dma_free_coherent(&ocpdev->dev,
- MAL_DT_ALIGN * maldata->num_tx_chans,
- mal->tx_virt_addr, mal->tx_phys_addr);
+ mal_reset(mal);
- if (mal->rx_virt_addr)
- dma_free_coherent(&ocpdev->dev,
- MAL_DT_ALIGN * maldata->num_rx_chans,
- mal->rx_virt_addr, mal->rx_phys_addr);
+ mal_dbg_register(mal->def->index, NULL);
+
+ dma_free_coherent(&ocpdev->dev,
+ sizeof(struct mal_descriptor) *
+ (NUM_TX_BUFF * maldata->num_tx_chans +
+ NUM_RX_BUFF * maldata->num_rx_chans), mal->bd_virt,
+ mal->bd_dma);
kfree(mal);
}
/* Structure for a device driver */
static struct ocp_device_id mal_ids[] = {
- {.vendor = OCP_ANY_ID,.function = OCP_FUNC_MAL},
- {.vendor = OCP_VENDOR_INVALID}
+ { .vendor = OCP_VENDOR_IBM, .function = OCP_FUNC_MAL },
+ { .vendor = OCP_VENDOR_INVALID}
};
static struct ocp_driver mal_driver = {
.remove = mal_remove,
};
-static int __init init_mals(void)
+int __init mal_init(void)
{
- int rc;
-
- rc = ocp_register_driver(&mal_driver);
- if (rc < 0) {
- ocp_unregister_driver(&mal_driver);
- return -ENODEV;
- }
-
- return 0;
+ MAL_DBG(": init" NL);
+ return ocp_register_driver(&mal_driver);
}
-static void __exit exit_mals(void)
+void __exit mal_exit(void)
{
+ MAL_DBG(": exit" NL);
ocp_unregister_driver(&mal_driver);
}
-
-module_init(init_mals);
-module_exit(exit_mals);
-#ifndef _IBM_EMAC_MAL_H
-#define _IBM_EMAC_MAL_H
+/*
+ * drivers/net/ibm_emac/ibm_emac_mal.h
+ *
+ * Memory Access Layer (MAL) support
+ *
+ * Copyright (c) 2004, 2005 Zultys Technologies.
+ * Eugene Surovegin <eugene.surovegin@zultys.com> or <ebs@ebshome.net>
+ *
+ * Based on original work by
+ * Armin Kuster <akuster@mvista.com>
+ * Copyright 2002 MontaVista Softare Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ */
+#ifndef __IBM_EMAC_MAL_H_
+#define __IBM_EMAC_MAL_H_
+#include <linux/config.h>
+#include <linux/init.h>
#include <linux/list.h>
+#include <linux/netdevice.h>
-#define MAL_DT_ALIGN (4096) /* Alignment for each channel's descriptor table */
+#include <asm/io.h>
-#define MAL_CHAN_MASK(chan) (0x80000000 >> (chan))
+/*
+ * These MAL "versions" probably aren't the real versions IBM uses for these
+ * MAL cores, I assigned them just to make #ifdefs in this file nicer and
+ * reflect the fact that 40x and 44x have slightly different MALs. --ebs
+ */
+#if defined(CONFIG_405GP) || defined(CONFIG_405GPR) || defined(CONFIG_405EP) || \
+ defined(CONFIG_440EP) || defined(CONFIG_NP405H)
+#define MAL_VERSION 1
+#elif defined(CONFIG_440GP) || defined(CONFIG_440GX) || defined(CONFIG_440SP)
+#define MAL_VERSION 2
+#else
+#error "Unknown SoC, please check chip manual and choose MAL 'version'"
+#endif
+
+/* MALx DCR registers */
+#define MAL_CFG 0x00
+#define MAL_CFG_SR 0x80000000
+#define MAL_CFG_PLBB 0x00004000
+#define MAL_CFG_OPBBL 0x00000080
+#define MAL_CFG_EOPIE 0x00000004
+#define MAL_CFG_LEA 0x00000002
+#define MAL_CFG_SD 0x00000001
+#if MAL_VERSION == 1
+#define MAL_CFG_PLBP_MASK 0x00c00000
+#define MAL_CFG_PLBP_10 0x00800000
+#define MAL_CFG_GA 0x00200000
+#define MAL_CFG_OA 0x00100000
+#define MAL_CFG_PLBLE 0x00080000
+#define MAL_CFG_PLBT_MASK 0x00078000
+#define MAL_CFG_DEFAULT (MAL_CFG_PLBP_10 | MAL_CFG_PLBT_MASK)
+#elif MAL_VERSION == 2
+#define MAL_CFG_RPP_MASK 0x00c00000
+#define MAL_CFG_RPP_10 0x00800000
+#define MAL_CFG_RMBS_MASK 0x00300000
+#define MAL_CFG_WPP_MASK 0x000c0000
+#define MAL_CFG_WPP_10 0x00080000
+#define MAL_CFG_WMBS_MASK 0x00030000
+#define MAL_CFG_PLBLE 0x00008000
+#define MAL_CFG_DEFAULT (MAL_CFG_RMBS_MASK | MAL_CFG_WMBS_MASK | \
+ MAL_CFG_RPP_10 | MAL_CFG_WPP_10)
+#else
+#error "Unknown MAL version"
+#endif
+
+#define MAL_ESR 0x01
+#define MAL_ESR_EVB 0x80000000
+#define MAL_ESR_CIDT 0x40000000
+#define MAL_ESR_CID_MASK 0x3e000000
+#define MAL_ESR_CID_SHIFT 25
+#define MAL_ESR_DE 0x00100000
+#define MAL_ESR_OTE 0x00040000
+#define MAL_ESR_OSE 0x00020000
+#define MAL_ESR_PEIN 0x00010000
+#define MAL_ESR_DEI 0x00000010
+#define MAL_ESR_OTEI 0x00000004
+#define MAL_ESR_OSEI 0x00000002
+#define MAL_ESR_PBEI 0x00000001
+#if MAL_VERSION == 1
+#define MAL_ESR_ONE 0x00080000
+#define MAL_ESR_ONEI 0x00000008
+#elif MAL_VERSION == 2
+#define MAL_ESR_PTE 0x00800000
+#define MAL_ESR_PRE 0x00400000
+#define MAL_ESR_PWE 0x00200000
+#define MAL_ESR_PTEI 0x00000080
+#define MAL_ESR_PREI 0x00000040
+#define MAL_ESR_PWEI 0x00000020
+#else
+#error "Unknown MAL version"
+#endif
+
+#define MAL_IER 0x02
+#define MAL_IER_DE 0x00000010
+#define MAL_IER_OTE 0x00000004
+#define MAL_IER_OE 0x00000002
+#define MAL_IER_PE 0x00000001
+#if MAL_VERSION == 1
+#define MAL_IER_NWE 0x00000008
+#define MAL_IER_SOC_EVENTS MAL_IER_NWE
+#elif MAL_VERSION == 2
+#define MAL_IER_PT 0x00000080
+#define MAL_IER_PRE 0x00000040
+#define MAL_IER_PWE 0x00000020
+#define MAL_IER_SOC_EVENTS (MAL_IER_PT | MAL_IER_PRE | MAL_IER_PWE)
+#else
+#error "Unknown MAL version"
+#endif
+#define MAL_IER_EVENTS (MAL_IER_SOC_EVENTS | MAL_IER_OTE | \
+ MAL_IER_OTE | MAL_IER_OE | MAL_IER_PE)
+
+#define MAL_TXCASR 0x04
+#define MAL_TXCARR 0x05
+#define MAL_TXEOBISR 0x06
+#define MAL_TXDEIR 0x07
+#define MAL_RXCASR 0x10
+#define MAL_RXCARR 0x11
+#define MAL_RXEOBISR 0x12
+#define MAL_RXDEIR 0x13
+#define MAL_TXCTPR(n) ((n) + 0x20)
+#define MAL_RXCTPR(n) ((n) + 0x40)
+#define MAL_RCBS(n) ((n) + 0x60)
+
+/* In reality MAL can handle TX buffers up to 4095 bytes long,
+ * but this isn't a good round number :) --ebs
+ */
+#define MAL_MAX_TX_SIZE 4080
+#define MAL_MAX_RX_SIZE 4080
+
+static inline int mal_rx_size(int len)
+{
+ len = (len + 0xf) & ~0xf;
+ return len > MAL_MAX_RX_SIZE ? MAL_MAX_RX_SIZE : len;
+}
+
+static inline int mal_tx_chunks(int len)
+{
+ return (len + MAL_MAX_TX_SIZE - 1) / MAL_MAX_TX_SIZE;
+}
+
+#define MAL_CHAN_MASK(n) (0x80000000 >> (n))
/* MAL Buffer Descriptor structure */
struct mal_descriptor {
- unsigned short ctrl; /* MAL / Commac status control bits */
- short data_len; /* Max length is 4K-1 (12 bits) */
- unsigned char *data_ptr; /* pointer to actual data buffer */
-} __attribute__ ((packed));
+ u16 ctrl; /* MAL / Commac status control bits */
+ u16 data_len; /* Max length is 4K-1 (12 bits) */
+ u32 data_ptr; /* pointer to actual data buffer */
+};
/* the following defines are for the MadMAL status and control registers. */
/* MADMAL transmit and receive status/control bits */
-#define MAL_RX_CTRL_EMPTY 0x8000
-#define MAL_RX_CTRL_WRAP 0x4000
-#define MAL_RX_CTRL_CM 0x2000
-#define MAL_RX_CTRL_LAST 0x1000
-#define MAL_RX_CTRL_FIRST 0x0800
-#define MAL_RX_CTRL_INTR 0x0400
-
-#define MAL_TX_CTRL_READY 0x8000
-#define MAL_TX_CTRL_WRAP 0x4000
-#define MAL_TX_CTRL_CM 0x2000
-#define MAL_TX_CTRL_LAST 0x1000
-#define MAL_TX_CTRL_INTR 0x0400
+#define MAL_RX_CTRL_EMPTY 0x8000
+#define MAL_RX_CTRL_WRAP 0x4000
+#define MAL_RX_CTRL_CM 0x2000
+#define MAL_RX_CTRL_LAST 0x1000
+#define MAL_RX_CTRL_FIRST 0x0800
+#define MAL_RX_CTRL_INTR 0x0400
+#define MAL_RX_CTRL_SINGLE (MAL_RX_CTRL_LAST | MAL_RX_CTRL_FIRST)
+#define MAL_IS_SINGLE_RX(ctrl) (((ctrl) & MAL_RX_CTRL_SINGLE) == MAL_RX_CTRL_SINGLE)
+
+#define MAL_TX_CTRL_READY 0x8000
+#define MAL_TX_CTRL_WRAP 0x4000
+#define MAL_TX_CTRL_CM 0x2000
+#define MAL_TX_CTRL_LAST 0x1000
+#define MAL_TX_CTRL_INTR 0x0400
struct mal_commac_ops {
- void (*txeob) (void *dev, u32 chanmask);
- void (*txde) (void *dev, u32 chanmask);
- void (*rxeob) (void *dev, u32 chanmask);
- void (*rxde) (void *dev, u32 chanmask);
+ void (*poll_tx) (void *dev);
+ int (*poll_rx) (void *dev, int budget);
+ int (*peek_rx) (void *dev);
+ void (*rxde) (void *dev);
};
struct mal_commac {
- struct mal_commac_ops *ops;
- void *dev;
- u32 tx_chan_mask, rx_chan_mask;
- struct list_head list;
+ struct mal_commac_ops *ops;
+ void *dev;
+ struct list_head poll_list;
+ int rx_stopped;
+
+ u32 tx_chan_mask;
+ u32 rx_chan_mask;
+ struct list_head list;
};
struct ibm_ocp_mal {
- int dcrbase;
+ int dcrbase;
- struct list_head commac;
- u32 tx_chan_mask, rx_chan_mask;
+ struct list_head poll_list;
+ struct net_device poll_dev;
- dma_addr_t tx_phys_addr;
- struct mal_descriptor *tx_virt_addr;
+ struct list_head list;
+ u32 tx_chan_mask;
+ u32 rx_chan_mask;
- dma_addr_t rx_phys_addr;
- struct mal_descriptor *rx_virt_addr;
-};
+ dma_addr_t bd_dma;
+ struct mal_descriptor *bd_virt;
-#define GET_MAL_STANZA(base,dcrn) \
- case base: \
- x = mfdcr(dcrn(base)); \
- break;
-
-#define SET_MAL_STANZA(base,dcrn, val) \
- case base: \
- mtdcr(dcrn(base), (val)); \
- break;
-
-#define GET_MAL0_STANZA(dcrn) GET_MAL_STANZA(DCRN_MAL_BASE,dcrn)
-#define SET_MAL0_STANZA(dcrn,val) SET_MAL_STANZA(DCRN_MAL_BASE,dcrn,val)
-
-#ifdef DCRN_MAL1_BASE
-#define GET_MAL1_STANZA(dcrn) GET_MAL_STANZA(DCRN_MAL1_BASE,dcrn)
-#define SET_MAL1_STANZA(dcrn,val) SET_MAL_STANZA(DCRN_MAL1_BASE,dcrn,val)
-#else /* ! DCRN_MAL1_BASE */
-#define GET_MAL1_STANZA(dcrn)
-#define SET_MAL1_STANZA(dcrn,val)
-#endif
+ struct ocp_def *def;
+};
-#define get_mal_dcrn(mal, dcrn) ({ \
- u32 x; \
- switch ((mal)->dcrbase) { \
- GET_MAL0_STANZA(dcrn) \
- GET_MAL1_STANZA(dcrn) \
- default: \
- x = 0; \
- BUG(); \
- } \
-x; })
-
-#define set_mal_dcrn(mal, dcrn, val) do { \
- switch ((mal)->dcrbase) { \
- SET_MAL0_STANZA(dcrn,val) \
- SET_MAL1_STANZA(dcrn,val) \
- default: \
- BUG(); \
- } } while (0)
-
-static inline void mal_enable_tx_channels(struct ibm_ocp_mal *mal, u32 chanmask)
+static inline u32 get_mal_dcrn(struct ibm_ocp_mal *mal, int reg)
{
- set_mal_dcrn(mal, DCRN_MALTXCASR,
- get_mal_dcrn(mal, DCRN_MALTXCASR) | chanmask);
+ return mfdcr(mal->dcrbase + reg);
}
-static inline void mal_disable_tx_channels(struct ibm_ocp_mal *mal,
- u32 chanmask)
+static inline void set_mal_dcrn(struct ibm_ocp_mal *mal, int reg, u32 val)
{
- set_mal_dcrn(mal, DCRN_MALTXCARR, chanmask);
+ mtdcr(mal->dcrbase + reg, val);
}
-static inline void mal_enable_rx_channels(struct ibm_ocp_mal *mal, u32 chanmask)
-{
- set_mal_dcrn(mal, DCRN_MALRXCASR,
- get_mal_dcrn(mal, DCRN_MALRXCASR) | chanmask);
-}
+/* Register MAL devices */
+int mal_init(void) __init;
+void mal_exit(void) __exit;
-static inline void mal_disable_rx_channels(struct ibm_ocp_mal *mal,
- u32 chanmask)
-{
- set_mal_dcrn(mal, DCRN_MALRXCARR, chanmask);
-}
+int mal_register_commac(struct ibm_ocp_mal *mal,
+ struct mal_commac *commac) __init;
+void mal_unregister_commac(struct ibm_ocp_mal *mal,
+ struct mal_commac *commac) __exit;
+int mal_set_rcbs(struct ibm_ocp_mal *mal, int channel, unsigned long size);
+
+/* Returns BD ring offset for a particular channel
+ (in 'struct mal_descriptor' elements)
+*/
+int mal_tx_bd_offset(struct ibm_ocp_mal *mal, int channel);
+int mal_rx_bd_offset(struct ibm_ocp_mal *mal, int channel);
+
+void mal_enable_tx_channel(struct ibm_ocp_mal *mal, int channel);
+void mal_disable_tx_channel(struct ibm_ocp_mal *mal, int channel);
+void mal_enable_rx_channel(struct ibm_ocp_mal *mal, int channel);
+void mal_disable_rx_channel(struct ibm_ocp_mal *mal, int channel);
-extern int mal_register_commac(struct ibm_ocp_mal *mal,
- struct mal_commac *commac);
-extern int mal_unregister_commac(struct ibm_ocp_mal *mal,
- struct mal_commac *commac);
+/* Add/remove EMAC to/from MAL polling list */
+void mal_poll_add(struct ibm_ocp_mal *mal, struct mal_commac *commac);
+void mal_poll_del(struct ibm_ocp_mal *mal, struct mal_commac *commac);
+
+/* Ethtool MAL registers */
+struct ibm_mal_regs {
+ u32 tx_count;
+ u32 rx_count;
+
+ u32 cfg;
+ u32 esr;
+ u32 ier;
+ u32 tx_casr;
+ u32 tx_carr;
+ u32 tx_eobisr;
+ u32 tx_deir;
+ u32 rx_casr;
+ u32 rx_carr;
+ u32 rx_eobisr;
+ u32 rx_deir;
+ u32 tx_ctpr[32];
+ u32 rx_ctpr[32];
+ u32 rcbs[32];
+};
-extern int mal_set_rcbs(struct ibm_ocp_mal *mal, int channel,
- unsigned long size);
+int mal_get_regs_len(struct ibm_ocp_mal *mal);
+void *mal_dump_regs(struct ibm_ocp_mal *mal, void *buf);
-#endif /* _IBM_EMAC_MAL_H */
+#endif /* __IBM_EMAC_MAL_H_ */
/*
- * ibm_ocp_phy.c
+ * drivers/net/ibm_emac/ibm_emac_phy.c
*
- * PHY drivers for the ibm ocp ethernet driver. Borrowed
- * from sungem_phy.c, though I only kept the generic MII
+ * Driver for PowerPC 4xx on-chip ethernet controller, PHY support.
+ * Borrowed from sungem_phy.c, though I only kept the generic MII
* driver for now.
*
* This file should be shared with other drivers or eventually
* merged as the "low level" part of miilib
*
* (c) 2003, Benjamin Herrenscmidt (benh@kernel.crashing.org)
+ * (c) 2004-2005, Eugene Surovegin <ebs@ebshome.net>
*
*/
-
#include <linux/config.h>
-
#include <linux/module.h>
-
#include <linux/kernel.h>
-#include <linux/sched.h>
#include <linux/types.h>
#include <linux/netdevice.h>
-#include <linux/etherdevice.h>
#include <linux/mii.h>
#include <linux/ethtool.h>
#include <linux/delay.h>
+#include <asm/ocp.h>
+
#include "ibm_emac_phy.h"
-static int reset_one_mii_phy(struct mii_phy *phy, int phy_id)
+static inline int phy_read(struct mii_phy *phy, int reg)
+{
+ return phy->mdio_read(phy->dev, phy->address, reg);
+}
+
+static inline void phy_write(struct mii_phy *phy, int reg, int val)
{
- u16 val;
+ phy->mdio_write(phy->dev, phy->address, reg, val);
+}
+
+int mii_reset_phy(struct mii_phy *phy)
+{
+ int val;
int limit = 10000;
- val = __phy_read(phy, phy_id, MII_BMCR);
+ val = phy_read(phy, MII_BMCR);
val &= ~BMCR_ISOLATE;
val |= BMCR_RESET;
- __phy_write(phy, phy_id, MII_BMCR, val);
+ phy_write(phy, MII_BMCR, val);
- udelay(100);
+ udelay(300);
while (limit--) {
- val = __phy_read(phy, phy_id, MII_BMCR);
- if ((val & BMCR_RESET) == 0)
+ val = phy_read(phy, MII_BMCR);
+ if (val >= 0 && (val & BMCR_RESET) == 0)
break;
udelay(10);
}
if ((val & BMCR_ISOLATE) && limit > 0)
- __phy_write(phy, phy_id, MII_BMCR, val & ~BMCR_ISOLATE);
-
- return (limit <= 0);
-}
-
-static int cis8201_init(struct mii_phy *phy)
-{
- u16 epcr;
-
- epcr = phy_read(phy, MII_CIS8201_EPCR);
- epcr &= ~EPCR_MODE_MASK;
-
- switch (phy->mode) {
- case PHY_MODE_TBI:
- epcr |= EPCR_TBI_MODE;
- break;
- case PHY_MODE_RTBI:
- epcr |= EPCR_RTBI_MODE;
- break;
- case PHY_MODE_GMII:
- epcr |= EPCR_GMII_MODE;
- break;
- case PHY_MODE_RGMII:
- default:
- epcr |= EPCR_RGMII_MODE;
- }
+ phy_write(phy, MII_BMCR, val & ~BMCR_ISOLATE);
- phy_write(phy, MII_CIS8201_EPCR, epcr);
-
- return 0;
+ return limit <= 0;
}
static int genmii_setup_aneg(struct mii_phy *phy, u32 advertise)
{
- u16 ctl, adv;
+ int ctl, adv;
- phy->autoneg = 1;
+ phy->autoneg = AUTONEG_ENABLE;
phy->speed = SPEED_10;
phy->duplex = DUPLEX_HALF;
- phy->pause = 0;
+ phy->pause = phy->asym_pause = 0;
phy->advertising = advertise;
/* Setup standard advertise */
adv = phy_read(phy, MII_ADVERTISE);
- adv &= ~(ADVERTISE_ALL | ADVERTISE_100BASE4);
+ if (adv < 0)
+ return adv;
+ adv &= ~(ADVERTISE_ALL | ADVERTISE_100BASE4 | ADVERTISE_PAUSE_CAP |
+ ADVERTISE_PAUSE_ASYM);
if (advertise & ADVERTISED_10baseT_Half)
adv |= ADVERTISE_10HALF;
if (advertise & ADVERTISED_10baseT_Full)
adv |= ADVERTISE_100HALF;
if (advertise & ADVERTISED_100baseT_Full)
adv |= ADVERTISE_100FULL;
+ if (advertise & ADVERTISED_Pause)
+ adv |= ADVERTISE_PAUSE_CAP;
+ if (advertise & ADVERTISED_Asym_Pause)
+ adv |= ADVERTISE_PAUSE_ASYM;
phy_write(phy, MII_ADVERTISE, adv);
+ if (phy->features &
+ (SUPPORTED_1000baseT_Full | SUPPORTED_1000baseT_Half)) {
+ adv = phy_read(phy, MII_CTRL1000);
+ if (adv < 0)
+ return adv;
+ adv &= ~(ADVERTISE_1000FULL | ADVERTISE_1000HALF);
+ if (advertise & ADVERTISED_1000baseT_Full)
+ adv |= ADVERTISE_1000FULL;
+ if (advertise & ADVERTISED_1000baseT_Half)
+ adv |= ADVERTISE_1000HALF;
+ phy_write(phy, MII_CTRL1000, adv);
+ }
+
/* Start/Restart aneg */
ctl = phy_read(phy, MII_BMCR);
ctl |= (BMCR_ANENABLE | BMCR_ANRESTART);
static int genmii_setup_forced(struct mii_phy *phy, int speed, int fd)
{
- u16 ctl;
+ int ctl;
- phy->autoneg = 0;
+ phy->autoneg = AUTONEG_DISABLE;
phy->speed = speed;
phy->duplex = fd;
- phy->pause = 0;
+ phy->pause = phy->asym_pause = 0;
ctl = phy_read(phy, MII_BMCR);
+ if (ctl < 0)
+ return ctl;
ctl &= ~(BMCR_FULLDPLX | BMCR_SPEED100 | BMCR_ANENABLE);
/* First reset the PHY */
ctl |= BMCR_SPEED100;
break;
case SPEED_1000:
+ ctl |= BMCR_SPEED1000;
+ break;
default:
return -EINVAL;
}
static int genmii_poll_link(struct mii_phy *phy)
{
- u16 status;
+ int status;
- (void)phy_read(phy, MII_BMSR);
+ /* Clear latched value with dummy read */
+ phy_read(phy, MII_BMSR);
status = phy_read(phy, MII_BMSR);
- if ((status & BMSR_LSTATUS) == 0)
+ if (status < 0 || (status & BMSR_LSTATUS) == 0)
return 0;
- if (phy->autoneg && !(status & BMSR_ANEGCOMPLETE))
+ if (phy->autoneg == AUTONEG_ENABLE && !(status & BMSR_ANEGCOMPLETE))
return 0;
return 1;
}
-#define MII_CIS8201_ACSR 0x1c
-#define ACSR_DUPLEX_STATUS 0x0020
-#define ACSR_SPEED_1000BASET 0x0010
-#define ACSR_SPEED_100BASET 0x0008
-
-static int cis8201_read_link(struct mii_phy *phy)
+static int genmii_read_link(struct mii_phy *phy)
{
- u16 acsr;
+ if (phy->autoneg == AUTONEG_ENABLE) {
+ int glpa = 0;
+ int lpa = phy_read(phy, MII_LPA) & phy_read(phy, MII_ADVERTISE);
+ if (lpa < 0)
+ return lpa;
+
+ if (phy->features &
+ (SUPPORTED_1000baseT_Full | SUPPORTED_1000baseT_Half)) {
+ int adv = phy_read(phy, MII_CTRL1000);
+ glpa = phy_read(phy, MII_STAT1000);
+
+ if (glpa < 0 || adv < 0)
+ return adv;
+
+ glpa &= adv << 2;
+ }
+
+ phy->speed = SPEED_10;
+ phy->duplex = DUPLEX_HALF;
+ phy->pause = phy->asym_pause = 0;
+
+ if (glpa & (LPA_1000FULL | LPA_1000HALF)) {
+ phy->speed = SPEED_1000;
+ if (glpa & LPA_1000FULL)
+ phy->duplex = DUPLEX_FULL;
+ } else if (lpa & (LPA_100FULL | LPA_100HALF)) {
+ phy->speed = SPEED_100;
+ if (lpa & LPA_100FULL)
+ phy->duplex = DUPLEX_FULL;
+ } else if (lpa & LPA_10FULL)
+ phy->duplex = DUPLEX_FULL;
- if (phy->autoneg) {
- acsr = phy_read(phy, MII_CIS8201_ACSR);
+ if (phy->duplex == DUPLEX_FULL) {
+ phy->pause = lpa & LPA_PAUSE_CAP ? 1 : 0;
+ phy->asym_pause = lpa & LPA_PAUSE_ASYM ? 1 : 0;
+ }
+ } else {
+ int bmcr = phy_read(phy, MII_BMCR);
+ if (bmcr < 0)
+ return bmcr;
- if (acsr & ACSR_DUPLEX_STATUS)
+ if (bmcr & BMCR_FULLDPLX)
phy->duplex = DUPLEX_FULL;
else
phy->duplex = DUPLEX_HALF;
- if (acsr & ACSR_SPEED_1000BASET) {
+ if (bmcr & BMCR_SPEED1000)
phy->speed = SPEED_1000;
- } else if (acsr & ACSR_SPEED_100BASET)
+ else if (bmcr & BMCR_SPEED100)
phy->speed = SPEED_100;
else
phy->speed = SPEED_10;
- phy->pause = 0;
- }
- /* On non-aneg, we assume what we put in BMCR is the speed,
- * though magic-aneg shouldn't prevent this case from occurring
- */
+ phy->pause = phy->asym_pause = 0;
+ }
return 0;
}
-static int genmii_read_link(struct mii_phy *phy)
+/* Generic implementation for most 10/100/1000 PHYs */
+static struct mii_phy_ops generic_phy_ops = {
+ .setup_aneg = genmii_setup_aneg,
+ .setup_forced = genmii_setup_forced,
+ .poll_link = genmii_poll_link,
+ .read_link = genmii_read_link
+};
+
+static struct mii_phy_def genmii_phy_def = {
+ .phy_id = 0x00000000,
+ .phy_id_mask = 0x00000000,
+ .name = "Generic MII",
+ .ops = &generic_phy_ops
+};
+
+/* CIS8201 */
+#define MII_CIS8201_EPCR 0x17
+#define EPCR_MODE_MASK 0x3000
+#define EPCR_GMII_MODE 0x0000
+#define EPCR_RGMII_MODE 0x1000
+#define EPCR_TBI_MODE 0x2000
+#define EPCR_RTBI_MODE 0x3000
+
+static int cis8201_init(struct mii_phy *phy)
{
- u16 lpa;
+ int epcr;
- if (phy->autoneg) {
- lpa = phy_read(phy, MII_LPA) & phy_read(phy, MII_ADVERTISE);
+ epcr = phy_read(phy, MII_CIS8201_EPCR);
+ if (epcr < 0)
+ return epcr;
- phy->speed = SPEED_10;
- phy->duplex = DUPLEX_HALF;
- phy->pause = 0;
+ epcr &= ~EPCR_MODE_MASK;
- if (lpa & (LPA_100FULL | LPA_100HALF)) {
- phy->speed = SPEED_100;
- if (lpa & LPA_100FULL)
- phy->duplex = DUPLEX_FULL;
- } else if (lpa & LPA_10FULL)
- phy->duplex = DUPLEX_FULL;
+ switch (phy->mode) {
+ case PHY_MODE_TBI:
+ epcr |= EPCR_TBI_MODE;
+ break;
+ case PHY_MODE_RTBI:
+ epcr |= EPCR_RTBI_MODE;
+ break;
+ case PHY_MODE_GMII:
+ epcr |= EPCR_GMII_MODE;
+ break;
+ case PHY_MODE_RGMII:
+ default:
+ epcr |= EPCR_RGMII_MODE;
}
- /* On non-aneg, we assume what we put in BMCR is the speed,
- * though magic-aneg shouldn't prevent this case from occurring
- */
+
+ phy_write(phy, MII_CIS8201_EPCR, epcr);
return 0;
}
-#define MII_BASIC_FEATURES (SUPPORTED_10baseT_Half | SUPPORTED_10baseT_Full | \
- SUPPORTED_100baseT_Half | SUPPORTED_100baseT_Full | \
- SUPPORTED_Autoneg | SUPPORTED_TP | SUPPORTED_MII)
-#define MII_GBIT_FEATURES (MII_BASIC_FEATURES | \
- SUPPORTED_1000baseT_Half | SUPPORTED_1000baseT_Full)
-
-/* CIS8201 phy ops */
static struct mii_phy_ops cis8201_phy_ops = {
- init:cis8201_init,
- setup_aneg:genmii_setup_aneg,
- setup_forced:genmii_setup_forced,
- poll_link:genmii_poll_link,
- read_link:cis8201_read_link
-};
-
-/* Generic implementation for most 10/100 PHYs */
-static struct mii_phy_ops generic_phy_ops = {
- setup_aneg:genmii_setup_aneg,
- setup_forced:genmii_setup_forced,
- poll_link:genmii_poll_link,
- read_link:genmii_read_link
+ .init = cis8201_init,
+ .setup_aneg = genmii_setup_aneg,
+ .setup_forced = genmii_setup_forced,
+ .poll_link = genmii_poll_link,
+ .read_link = genmii_read_link
};
static struct mii_phy_def cis8201_phy_def = {
- phy_id:0x000fc410,
- phy_id_mask:0x000ffff0,
- name:"CIS8201 Gigabit Ethernet",
- features:MII_GBIT_FEATURES,
- magic_aneg:0,
- ops:&cis8201_phy_ops
-};
-
-static struct mii_phy_def genmii_phy_def = {
- phy_id:0x00000000,
- phy_id_mask:0x00000000,
- name:"Generic MII",
- features:MII_BASIC_FEATURES,
- magic_aneg:0,
- ops:&generic_phy_ops
+ .phy_id = 0x000fc410,
+ .phy_id_mask = 0x000ffff0,
+ .name = "CIS8201 Gigabit Ethernet",
+ .ops = &cis8201_phy_ops
};
static struct mii_phy_def *mii_phy_table[] = {
NULL
};
-int mii_phy_probe(struct mii_phy *phy, int mii_id)
+int mii_phy_probe(struct mii_phy *phy, int address)
{
- int rc;
- u32 id;
struct mii_phy_def *def;
int i;
+ u32 id;
- phy->autoneg = 0;
+ phy->autoneg = AUTONEG_DISABLE;
phy->advertising = 0;
- phy->mii_id = mii_id;
- phy->speed = 0;
- phy->duplex = 0;
- phy->pause = 0;
-
- /* Take PHY out of isloate mode and reset it. */
- rc = reset_one_mii_phy(phy, mii_id);
- if (rc)
+ phy->address = address;
+ phy->speed = SPEED_10;
+ phy->duplex = DUPLEX_HALF;
+ phy->pause = phy->asym_pause = 0;
+
+ /* Take PHY out of isolate mode and reset it. */
+ if (mii_reset_phy(phy))
return -ENODEV;
/* Read ID and find matching entry */
- id = (phy_read(phy, MII_PHYSID1) << 16 | phy_read(phy, MII_PHYSID2))
- & 0xfffffff0;
+ id = (phy_read(phy, MII_PHYSID1) << 16) | phy_read(phy, MII_PHYSID2);
for (i = 0; (def = mii_phy_table[i]) != NULL; i++)
if ((id & def->phy_id_mask) == def->phy_id)
break;
/* Should never be NULL (we have a generic entry), but... */
- if (def == NULL)
+ if (!def)
return -ENODEV;
phy->def = def;
+ /* Determine PHY features if needed */
+ phy->features = def->features;
+ if (!phy->features) {
+ u16 bmsr = phy_read(phy, MII_BMSR);
+ if (bmsr & BMSR_ANEGCAPABLE)
+ phy->features |= SUPPORTED_Autoneg;
+ if (bmsr & BMSR_10HALF)
+ phy->features |= SUPPORTED_10baseT_Half;
+ if (bmsr & BMSR_10FULL)
+ phy->features |= SUPPORTED_10baseT_Full;
+ if (bmsr & BMSR_100HALF)
+ phy->features |= SUPPORTED_100baseT_Half;
+ if (bmsr & BMSR_100FULL)
+ phy->features |= SUPPORTED_100baseT_Full;
+ if (bmsr & BMSR_ESTATEN) {
+ u16 esr = phy_read(phy, MII_ESTATUS);
+ if (esr & ESTATUS_1000_TFULL)
+ phy->features |= SUPPORTED_1000baseT_Full;
+ if (esr & ESTATUS_1000_THALF)
+ phy->features |= SUPPORTED_1000baseT_Half;
+ }
+ phy->features |= SUPPORTED_MII;
+ }
+
/* Setup default advertising */
- phy->advertising = def->features;
+ phy->advertising = phy->features;
return 0;
}
-
/*
- * ibm_emac_phy.h
- *
+ * drivers/net/ibm_emac/ibm_emac_phy.h
*
- * Benjamin Herrenschmidt <benh@kernel.crashing.org>
- * February 2003
+ * Driver for PowerPC 4xx on-chip ethernet controller, PHY support
*
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
+ * Benjamin Herrenschmidt <benh@kernel.crashing.org>
+ * February 2003
*
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
+ * Minor additions by Eugene Surovegin <ebs@ebshome.net>, 2004
*
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
*
* This file basically duplicates sungem_phy.{c,h} with different PHYs
* supported. I'm looking into merging that in a single mii layer more
* flexible than mii.c
*/
-#ifndef _IBM_EMAC_PHY_H_
-#define _IBM_EMAC_PHY_H_
-
-/*
- * PHY mode settings
- * Used for multi-mode capable PHYs
- */
-#define PHY_MODE_NA 0
-#define PHY_MODE_MII 1
-#define PHY_MODE_RMII 2
-#define PHY_MODE_SMII 3
-#define PHY_MODE_RGMII 4
-#define PHY_MODE_TBI 5
-#define PHY_MODE_GMII 6
-#define PHY_MODE_RTBI 7
-#define PHY_MODE_SGMII 8
-
-/*
- * PHY specific registers/values
- */
-
-/* CIS8201 */
-#define MII_CIS8201_EPCR 0x17
-#define EPCR_MODE_MASK 0x3000
-#define EPCR_GMII_MODE 0x0000
-#define EPCR_RGMII_MODE 0x1000
-#define EPCR_TBI_MODE 0x2000
-#define EPCR_RTBI_MODE 0x3000
+#ifndef _IBM_OCP_PHY_H_
+#define _IBM_OCP_PHY_H_
struct mii_phy;
struct mii_phy_def {
u32 phy_id; /* Concatenated ID1 << 16 | ID2 */
u32 phy_id_mask; /* Significant bits */
- u32 features; /* Ethtool SUPPORTED_* defines */
+ u32 features; /* Ethtool SUPPORTED_* defines or
+ 0 for autodetect */
int magic_aneg; /* Autoneg does all speed test for us */
const char *name;
const struct mii_phy_ops *ops;
/* An instance of a PHY, partially borrowed from mii_if_info */
struct mii_phy {
struct mii_phy_def *def;
- int advertising;
- int mii_id;
+ u32 advertising; /* Ethtool ADVERTISED_* defines */
+ u32 features; /* Copied from mii_phy_def.features
+ or determined automaticaly */
+ int address; /* PHY address */
+ int mode; /* PHY mode */
/* 1: autoneg enabled, 0: disabled */
int autoneg;
int speed;
int duplex;
int pause;
-
- /* PHY mode - if needed */
- int mode;
+ int asym_pause;
/* Provided by host chip */
struct net_device *dev;
- int (*mdio_read) (struct net_device * dev, int mii_id, int reg);
- void (*mdio_write) (struct net_device * dev, int mii_id, int reg,
+ int (*mdio_read) (struct net_device * dev, int addr, int reg);
+ void (*mdio_write) (struct net_device * dev, int addr, int reg,
int val);
};
/* Pass in a struct mii_phy with dev, mdio_read and mdio_write
* filled, the remaining fields will be filled on return
*/
-extern int mii_phy_probe(struct mii_phy *phy, int mii_id);
-
-static inline int __phy_read(struct mii_phy *phy, int id, int reg)
-{
- return phy->mdio_read(phy->dev, id, reg);
-}
-
-static inline void __phy_write(struct mii_phy *phy, int id, int reg, int val)
-{
- phy->mdio_write(phy->dev, id, reg, val);
-}
-
-static inline int phy_read(struct mii_phy *phy, int reg)
-{
- return phy->mdio_read(phy->dev, phy->mii_id, reg);
-}
-
-static inline void phy_write(struct mii_phy *phy, int reg, int val)
-{
- phy->mdio_write(phy->dev, phy->mii_id, reg, val);
-}
+int mii_phy_probe(struct mii_phy *phy, int address);
+int mii_reset_phy(struct mii_phy *phy);
-#endif /* _IBM_EMAC_PHY_H_ */
+#endif /* _IBM_OCP_PHY_H_ */
--- /dev/null
+/*
+ * drivers/net/ibm_emac/ibm_emac_rgmii.c
+ *
+ * Driver for PowerPC 4xx on-chip ethernet controller, RGMII bridge support.
+ *
+ * Copyright (c) 2004, 2005 Zultys Technologies.
+ * Eugene Surovegin <eugene.surovegin@zultys.com> or <ebs@ebshome.net>
+ *
+ * Based on original work by
+ * Matt Porter <mporter@kernel.crashing.org>
+ * Copyright 2004 MontaVista Software, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ */
+#include <linux/config.h>
+#include <linux/kernel.h>
+#include <linux/ethtool.h>
+#include <asm/io.h>
+
+#include "ibm_emac_core.h"
+#include "ibm_emac_debug.h"
+
+/* RGMIIx_FER */
+#define RGMII_FER_MASK(idx) (0x7 << ((idx) * 4))
+#define RGMII_FER_RTBI(idx) (0x4 << ((idx) * 4))
+#define RGMII_FER_RGMII(idx) (0x5 << ((idx) * 4))
+#define RGMII_FER_TBI(idx) (0x6 << ((idx) * 4))
+#define RGMII_FER_GMII(idx) (0x7 << ((idx) * 4))
+
+/* RGMIIx_SSR */
+#define RGMII_SSR_MASK(idx) (0x7 << ((idx) * 8))
+#define RGMII_SSR_100(idx) (0x2 << ((idx) * 8))
+#define RGMII_SSR_1000(idx) (0x4 << ((idx) * 8))
+
+/* RGMII bridge supports only GMII/TBI and RGMII/RTBI PHYs */
+static inline int rgmii_valid_mode(int phy_mode)
+{
+ return phy_mode == PHY_MODE_GMII ||
+ phy_mode == PHY_MODE_RGMII ||
+ phy_mode == PHY_MODE_TBI ||
+ phy_mode == PHY_MODE_RTBI;
+}
+
+static inline const char *rgmii_mode_name(int mode)
+{
+ switch (mode) {
+ case PHY_MODE_RGMII:
+ return "RGMII";
+ case PHY_MODE_TBI:
+ return "TBI";
+ case PHY_MODE_GMII:
+ return "GMII";
+ case PHY_MODE_RTBI:
+ return "RTBI";
+ default:
+ BUG();
+ }
+}
+
+static inline u32 rgmii_mode_mask(int mode, int input)
+{
+ switch (mode) {
+ case PHY_MODE_RGMII:
+ return RGMII_FER_RGMII(input);
+ case PHY_MODE_TBI:
+ return RGMII_FER_TBI(input);
+ case PHY_MODE_GMII:
+ return RGMII_FER_GMII(input);
+ case PHY_MODE_RTBI:
+ return RGMII_FER_RTBI(input);
+ default:
+ BUG();
+ }
+}
+
+static int __init rgmii_init(struct ocp_device *ocpdev, int input, int mode)
+{
+ struct ibm_ocp_rgmii *dev = ocp_get_drvdata(ocpdev);
+ struct rgmii_regs *p;
+
+ RGMII_DBG("%d: init(%d, %d)" NL, ocpdev->def->index, input, mode);
+
+ if (!dev) {
+ dev = kzalloc(sizeof(struct ibm_ocp_rgmii), GFP_KERNEL);
+ if (!dev) {
+ printk(KERN_ERR
+ "rgmii%d: couldn't allocate device structure!\n",
+ ocpdev->def->index);
+ return -ENOMEM;
+ }
+
+ p = (struct rgmii_regs *)ioremap(ocpdev->def->paddr,
+ sizeof(struct rgmii_regs));
+ if (!p) {
+ printk(KERN_ERR
+ "rgmii%d: could not ioremap device registers!\n",
+ ocpdev->def->index);
+ kfree(dev);
+ return -ENOMEM;
+ }
+
+ dev->base = p;
+ ocp_set_drvdata(ocpdev, dev);
+
+ /* Disable all inputs by default */
+ out_be32(&p->fer, 0);
+ } else
+ p = dev->base;
+
+ /* Enable this input */
+ out_be32(&p->fer, in_be32(&p->fer) | rgmii_mode_mask(mode, input));
+
+ printk(KERN_NOTICE "rgmii%d: input %d in %s mode\n",
+ ocpdev->def->index, input, rgmii_mode_name(mode));
+
+ ++dev->users;
+ return 0;
+}
+
+int __init rgmii_attach(void *emac)
+{
+ struct ocp_enet_private *dev = emac;
+ struct ocp_func_emac_data *emacdata = dev->def->additions;
+
+ /* Check if we need to attach to a RGMII */
+ if (emacdata->rgmii_idx >= 0 && rgmii_valid_mode(emacdata->phy_mode)) {
+ dev->rgmii_input = emacdata->rgmii_mux;
+ dev->rgmii_dev =
+ ocp_find_device(OCP_VENDOR_IBM, OCP_FUNC_RGMII,
+ emacdata->rgmii_idx);
+ if (!dev->rgmii_dev) {
+ printk(KERN_ERR "emac%d: unknown rgmii%d!\n",
+ dev->def->index, emacdata->rgmii_idx);
+ return -ENODEV;
+ }
+ if (rgmii_init
+ (dev->rgmii_dev, dev->rgmii_input, emacdata->phy_mode)) {
+ printk(KERN_ERR
+ "emac%d: rgmii%d initialization failed!\n",
+ dev->def->index, emacdata->rgmii_idx);
+ return -ENODEV;
+ }
+ }
+ return 0;
+}
+
+void rgmii_set_speed(struct ocp_device *ocpdev, int input, int speed)
+{
+ struct ibm_ocp_rgmii *dev = ocp_get_drvdata(ocpdev);
+ u32 ssr = in_be32(&dev->base->ssr) & ~RGMII_SSR_MASK(input);
+
+ RGMII_DBG("%d: speed(%d, %d)" NL, ocpdev->def->index, input, speed);
+
+ if (speed == SPEED_1000)
+ ssr |= RGMII_SSR_1000(input);
+ else if (speed == SPEED_100)
+ ssr |= RGMII_SSR_100(input);
+
+ out_be32(&dev->base->ssr, ssr);
+}
+
+void __exit __rgmii_fini(struct ocp_device *ocpdev, int input)
+{
+ struct ibm_ocp_rgmii *dev = ocp_get_drvdata(ocpdev);
+ BUG_ON(!dev || dev->users == 0);
+
+ RGMII_DBG("%d: fini(%d)" NL, ocpdev->def->index, input);
+
+ /* Disable this input */
+ out_be32(&dev->base->fer,
+ in_be32(&dev->base->fer) & ~RGMII_FER_MASK(input));
+
+ if (!--dev->users) {
+ /* Free everything if this is the last user */
+ ocp_set_drvdata(ocpdev, NULL);
+ iounmap((void *)dev->base);
+ kfree(dev);
+ }
+}
+
+int __rgmii_get_regs_len(struct ocp_device *ocpdev)
+{
+ return sizeof(struct emac_ethtool_regs_subhdr) +
+ sizeof(struct rgmii_regs);
+}
+
+void *rgmii_dump_regs(struct ocp_device *ocpdev, void *buf)
+{
+ struct ibm_ocp_rgmii *dev = ocp_get_drvdata(ocpdev);
+ struct emac_ethtool_regs_subhdr *hdr = buf;
+ struct rgmii_regs *regs = (struct rgmii_regs *)(hdr + 1);
+
+ hdr->version = 0;
+ hdr->index = ocpdev->def->index;
+ memcpy_fromio(regs, dev->base, sizeof(struct rgmii_regs));
+ return regs + 1;
+}
/*
- * Defines for the IBM RGMII bridge
+ * drivers/net/ibm_emac/ibm_emac_rgmii.c
+ *
+ * Driver for PowerPC 4xx on-chip ethernet controller, RGMII bridge support.
*
* Based on ocp_zmii.h/ibm_emac_zmii.h
* Armin Kuster akuster@mvista.com
* Copyright 2004 MontaVista Software, Inc.
* Matt Porter <mporter@kernel.crashing.org>
*
+ * Copyright (c) 2004, 2005 Zultys Technologies.
+ * Eugene Surovegin <eugene.surovegin@zultys.com> or <ebs@ebshome.net>
+ *
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
#include <linux/config.h>
/* RGMII bridge */
-typedef struct rgmii_regs {
+struct rgmii_regs {
u32 fer; /* Function enable register */
u32 ssr; /* Speed select register */
-} rgmii_t;
-
-#define RGMII_INPUTS 4
+};
/* RGMII device */
struct ibm_ocp_rgmii {
struct rgmii_regs *base;
- int mode[RGMII_INPUTS];
int users; /* number of EMACs using this RGMII bridge */
};
-/* Fuctional Enable Reg */
-#define RGMII_FER_MASK(x) (0x00000007 << (4*x))
-#define RGMII_RTBI 0x00000004
-#define RGMII_RGMII 0x00000005
-#define RGMII_TBI 0x00000006
-#define RGMII_GMII 0x00000007
-
-/* Speed Selection reg */
+#ifdef CONFIG_IBM_EMAC_RGMII
+int rgmii_attach(void *emac) __init;
-#define RGMII_SP2_100 0x00000002
-#define RGMII_SP2_1000 0x00000004
-#define RGMII_SP3_100 0x00000200
-#define RGMII_SP3_1000 0x00000400
+void __rgmii_fini(struct ocp_device *ocpdev, int input) __exit;
+static inline void rgmii_fini(struct ocp_device *ocpdev, int input)
+{
+ if (ocpdev)
+ __rgmii_fini(ocpdev, input);
+}
-#define RGMII_MII2_SPDMASK 0x00000007
-#define RGMII_MII3_SPDMASK 0x00000700
+void rgmii_set_speed(struct ocp_device *ocpdev, int input, int speed);
-#define RGMII_MII2_100MB RGMII_SP2_100 & ~RGMII_SP2_1000
-#define RGMII_MII2_1000MB RGMII_SP2_1000 & ~RGMII_SP2_100
-#define RGMII_MII2_10MB ~(RGMII_SP2_100 | RGMII_SP2_1000)
-#define RGMII_MII3_100MB RGMII_SP3_100 & ~RGMII_SP3_1000
-#define RGMII_MII3_1000MB RGMII_SP3_1000 & ~RGMII_SP3_100
-#define RGMII_MII3_10MB ~(RGMII_SP3_100 | RGMII_SP3_1000)
+int __rgmii_get_regs_len(struct ocp_device *ocpdev);
+static inline int rgmii_get_regs_len(struct ocp_device *ocpdev)
+{
+ return ocpdev ? __rgmii_get_regs_len(ocpdev) : 0;
+}
-#define RTBI 0
-#define RGMII 1
-#define TBI 2
-#define GMII 3
+void *rgmii_dump_regs(struct ocp_device *ocpdev, void *buf);
+#else
+# define rgmii_attach(x) 0
+# define rgmii_fini(x,y) ((void)0)
+# define rgmii_set_speed(x,y,z) ((void)0)
+# define rgmii_get_regs_len(x) 0
+# define rgmii_dump_regs(x,buf) (buf)
+#endif /* !CONFIG_IBM_EMAC_RGMII */
#endif /* _IBM_EMAC_RGMII_H_ */
--- /dev/null
+/*
+ * drivers/net/ibm_emac/ibm_emac_tah.c
+ *
+ * Driver for PowerPC 4xx on-chip ethernet controller, TAH support.
+ *
+ * Copyright 2004 MontaVista Software, Inc.
+ * Matt Porter <mporter@kernel.crashing.org>
+ *
+ * Copyright (c) 2005 Eugene Surovegin <ebs@ebshome.net>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+#include <linux/config.h>
+#include <asm/io.h>
+
+#include "ibm_emac_core.h"
+
+static int __init tah_init(struct ocp_device *ocpdev)
+{
+ struct tah_regs *p;
+
+ if (ocp_get_drvdata(ocpdev)) {
+ printk(KERN_ERR "tah%d: already in use!\n", ocpdev->def->index);
+ return -EBUSY;
+ }
+
+ /* Initialize TAH and enable IPv4 checksum verification, no TSO yet */
+ p = (struct tah_regs *)ioremap(ocpdev->def->paddr, sizeof(*p));
+ if (!p) {
+ printk(KERN_ERR "tah%d: could not ioremap device registers!\n",
+ ocpdev->def->index);
+ return -ENOMEM;
+ }
+ ocp_set_drvdata(ocpdev, p);
+ __tah_reset(ocpdev);
+
+ return 0;
+}
+
+int __init tah_attach(void *emac)
+{
+ struct ocp_enet_private *dev = emac;
+ struct ocp_func_emac_data *emacdata = dev->def->additions;
+
+ /* Check if we need to attach to a TAH */
+ if (emacdata->tah_idx >= 0) {
+ dev->tah_dev = ocp_find_device(OCP_ANY_ID, OCP_FUNC_TAH,
+ emacdata->tah_idx);
+ if (!dev->tah_dev) {
+ printk(KERN_ERR "emac%d: unknown tah%d!\n",
+ dev->def->index, emacdata->tah_idx);
+ return -ENODEV;
+ }
+ if (tah_init(dev->tah_dev)) {
+ printk(KERN_ERR
+ "emac%d: tah%d initialization failed!\n",
+ dev->def->index, emacdata->tah_idx);
+ return -ENODEV;
+ }
+ }
+ return 0;
+}
+
+void __exit __tah_fini(struct ocp_device *ocpdev)
+{
+ struct tah_regs *p = ocp_get_drvdata(ocpdev);
+ BUG_ON(!p);
+ ocp_set_drvdata(ocpdev, NULL);
+ iounmap((void *)p);
+}
+
+void __tah_reset(struct ocp_device *ocpdev)
+{
+ struct tah_regs *p = ocp_get_drvdata(ocpdev);
+ int n;
+
+ /* Reset TAH */
+ out_be32(&p->mr, TAH_MR_SR);
+ n = 100;
+ while ((in_be32(&p->mr) & TAH_MR_SR) && n)
+ --n;
+
+ if (unlikely(!n))
+ printk(KERN_ERR "tah%d: reset timeout\n", ocpdev->def->index);
+
+ /* 10KB TAH TX FIFO accomodates the max MTU of 9000 */
+ out_be32(&p->mr,
+ TAH_MR_CVR | TAH_MR_ST_768 | TAH_MR_TFS_10KB | TAH_MR_DTFP |
+ TAH_MR_DIG);
+}
+
+int __tah_get_regs_len(struct ocp_device *ocpdev)
+{
+ return sizeof(struct emac_ethtool_regs_subhdr) +
+ sizeof(struct tah_regs);
+}
+
+void *tah_dump_regs(struct ocp_device *ocpdev, void *buf)
+{
+ struct tah_regs *dev = ocp_get_drvdata(ocpdev);
+ struct emac_ethtool_regs_subhdr *hdr = buf;
+ struct tah_regs *regs = (struct tah_regs *)(hdr + 1);
+
+ hdr->version = 0;
+ hdr->index = ocpdev->def->index;
+ memcpy_fromio(regs, dev, sizeof(struct tah_regs));
+ return regs + 1;
+}
/*
- * Defines for the IBM TAH
+ * drivers/net/ibm_emac/ibm_emac_tah.h
+ *
+ * Driver for PowerPC 4xx on-chip ethernet controller, TAH support.
*
* Copyright 2004 MontaVista Software, Inc.
* Matt Porter <mporter@kernel.crashing.org>
*
+ * Copyright (c) 2005 Eugene Surovegin <ebs@ebshome.net>
+ *
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
#ifndef _IBM_EMAC_TAH_H
#define _IBM_EMAC_TAH_H
+#include <linux/config.h>
+#include <linux/init.h>
+#include <asm/ocp.h>
+
/* TAH */
-typedef struct tah_regs {
- u32 tah_revid;
+struct tah_regs {
+ u32 revid;
u32 pad[3];
- u32 tah_mr;
- u32 tah_ssr0;
- u32 tah_ssr1;
- u32 tah_ssr2;
- u32 tah_ssr3;
- u32 tah_ssr4;
- u32 tah_ssr5;
- u32 tah_tsr;
-} tah_t;
+ u32 mr;
+ u32 ssr0;
+ u32 ssr1;
+ u32 ssr2;
+ u32 ssr3;
+ u32 ssr4;
+ u32 ssr5;
+ u32 tsr;
+};
/* TAH engine */
-#define TAH_MR_CVR 0x80000000
-#define TAH_MR_SR 0x40000000
-#define TAH_MR_ST_256 0x01000000
-#define TAH_MR_ST_512 0x02000000
-#define TAH_MR_ST_768 0x03000000
-#define TAH_MR_ST_1024 0x04000000
-#define TAH_MR_ST_1280 0x05000000
-#define TAH_MR_ST_1536 0x06000000
-#define TAH_MR_TFS_16KB 0x00000000
-#define TAH_MR_TFS_2KB 0x00200000
-#define TAH_MR_TFS_4KB 0x00400000
-#define TAH_MR_TFS_6KB 0x00600000
-#define TAH_MR_TFS_8KB 0x00800000
-#define TAH_MR_TFS_10KB 0x00a00000
-#define TAH_MR_DTFP 0x00100000
-#define TAH_MR_DIG 0x00080000
+#define TAH_MR_CVR 0x80000000
+#define TAH_MR_SR 0x40000000
+#define TAH_MR_ST_256 0x01000000
+#define TAH_MR_ST_512 0x02000000
+#define TAH_MR_ST_768 0x03000000
+#define TAH_MR_ST_1024 0x04000000
+#define TAH_MR_ST_1280 0x05000000
+#define TAH_MR_ST_1536 0x06000000
+#define TAH_MR_TFS_16KB 0x00000000
+#define TAH_MR_TFS_2KB 0x00200000
+#define TAH_MR_TFS_4KB 0x00400000
+#define TAH_MR_TFS_6KB 0x00600000
+#define TAH_MR_TFS_8KB 0x00800000
+#define TAH_MR_TFS_10KB 0x00a00000
+#define TAH_MR_DTFP 0x00100000
+#define TAH_MR_DIG 0x00080000
+
+#ifdef CONFIG_IBM_EMAC_TAH
+int tah_attach(void *emac) __init;
+
+void __tah_fini(struct ocp_device *ocpdev) __exit;
+static inline void tah_fini(struct ocp_device *ocpdev)
+{
+ if (ocpdev)
+ __tah_fini(ocpdev);
+}
+
+void __tah_reset(struct ocp_device *ocpdev);
+static inline void tah_reset(struct ocp_device *ocpdev)
+{
+ if (ocpdev)
+ __tah_reset(ocpdev);
+}
+
+int __tah_get_regs_len(struct ocp_device *ocpdev);
+static inline int tah_get_regs_len(struct ocp_device *ocpdev)
+{
+ return ocpdev ? __tah_get_regs_len(ocpdev) : 0;
+}
+
+void *tah_dump_regs(struct ocp_device *ocpdev, void *buf);
+#else
+# define tah_attach(x) 0
+# define tah_fini(x) ((void)0)
+# define tah_reset(x) ((void)0)
+# define tah_get_regs_len(x) 0
+# define tah_dump_regs(x,buf) (buf)
+#endif /* !CONFIG_IBM_EMAC_TAH */
#endif /* _IBM_EMAC_TAH_H */
--- /dev/null
+/*
+ * drivers/net/ibm_emac/ibm_emac_zmii.c
+ *
+ * Driver for PowerPC 4xx on-chip ethernet controller, ZMII bridge support.
+ *
+ * Copyright (c) 2004, 2005 Zultys Technologies.
+ * Eugene Surovegin <eugene.surovegin@zultys.com> or <ebs@ebshome.net>
+ *
+ * Based on original work by
+ * Armin Kuster <akuster@mvista.com>
+ * Copyright 2001 MontaVista Softare Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ */
+#include <linux/config.h>
+#include <linux/kernel.h>
+#include <linux/ethtool.h>
+#include <asm/io.h>
+
+#include "ibm_emac_core.h"
+#include "ibm_emac_debug.h"
+
+/* ZMIIx_FER */
+#define ZMII_FER_MDI(idx) (0x80000000 >> ((idx) * 4))
+#define ZMII_FER_MDI_ALL (ZMII_FER_MDI(0) | ZMII_FER_MDI(1) | \
+ ZMII_FER_MDI(2) | ZMII_FER_MDI(3))
+
+#define ZMII_FER_SMII(idx) (0x40000000 >> ((idx) * 4))
+#define ZMII_FER_RMII(idx) (0x20000000 >> ((idx) * 4))
+#define ZMII_FER_MII(idx) (0x10000000 >> ((idx) * 4))
+
+/* ZMIIx_SSR */
+#define ZMII_SSR_SCI(idx) (0x40000000 >> ((idx) * 4))
+#define ZMII_SSR_FSS(idx) (0x20000000 >> ((idx) * 4))
+#define ZMII_SSR_SP(idx) (0x10000000 >> ((idx) * 4))
+
+/* ZMII only supports MII, RMII and SMII
+ * we also support autodetection for backward compatibility
+ */
+static inline int zmii_valid_mode(int mode)
+{
+ return mode == PHY_MODE_MII ||
+ mode == PHY_MODE_RMII ||
+ mode == PHY_MODE_SMII ||
+ mode == PHY_MODE_NA;
+}
+
+static inline const char *zmii_mode_name(int mode)
+{
+ switch (mode) {
+ case PHY_MODE_MII:
+ return "MII";
+ case PHY_MODE_RMII:
+ return "RMII";
+ case PHY_MODE_SMII:
+ return "SMII";
+ default:
+ BUG();
+ }
+}
+
+static inline u32 zmii_mode_mask(int mode, int input)
+{
+ switch (mode) {
+ case PHY_MODE_MII:
+ return ZMII_FER_MII(input);
+ case PHY_MODE_RMII:
+ return ZMII_FER_RMII(input);
+ case PHY_MODE_SMII:
+ return ZMII_FER_SMII(input);
+ default:
+ return 0;
+ }
+}
+
+static int __init zmii_init(struct ocp_device *ocpdev, int input, int *mode)
+{
+ struct ibm_ocp_zmii *dev = ocp_get_drvdata(ocpdev);
+ struct zmii_regs *p;
+
+ ZMII_DBG("%d: init(%d, %d)" NL, ocpdev->def->index, input, *mode);
+
+ if (!dev) {
+ dev = kzalloc(sizeof(struct ibm_ocp_zmii), GFP_KERNEL);
+ if (!dev) {
+ printk(KERN_ERR
+ "zmii%d: couldn't allocate device structure!\n",
+ ocpdev->def->index);
+ return -ENOMEM;
+ }
+ dev->mode = PHY_MODE_NA;
+
+ p = (struct zmii_regs *)ioremap(ocpdev->def->paddr,
+ sizeof(struct zmii_regs));
+ if (!p) {
+ printk(KERN_ERR
+ "zmii%d: could not ioremap device registers!\n",
+ ocpdev->def->index);
+ kfree(dev);
+ return -ENOMEM;
+ }
+ dev->base = p;
+ ocp_set_drvdata(ocpdev, dev);
+
+ /* We may need FER value for autodetection later */
+ dev->fer_save = in_be32(&p->fer);
+
+ /* Disable all inputs by default */
+ out_be32(&p->fer, 0);
+ } else
+ p = dev->base;
+
+ if (!zmii_valid_mode(*mode)) {
+ /* Probably an EMAC connected to RGMII,
+ * but it still may need ZMII for MDIO
+ */
+ goto out;
+ }
+
+ /* Autodetect ZMII mode if not specified.
+ * This is only for backward compatibility with the old driver.
+ * Please, always specify PHY mode in your board port to avoid
+ * any surprises.
+ */
+ if (dev->mode == PHY_MODE_NA) {
+ if (*mode == PHY_MODE_NA) {
+ u32 r = dev->fer_save;
+
+ ZMII_DBG("%d: autodetecting mode, FER = 0x%08x" NL,
+ ocpdev->def->index, r);
+
+ if (r & (ZMII_FER_MII(0) | ZMII_FER_MII(1)))
+ dev->mode = PHY_MODE_MII;
+ else if (r & (ZMII_FER_RMII(0) | ZMII_FER_RMII(1)))
+ dev->mode = PHY_MODE_RMII;
+ else
+ dev->mode = PHY_MODE_SMII;
+ } else
+ dev->mode = *mode;
+
+ printk(KERN_NOTICE "zmii%d: bridge in %s mode\n",
+ ocpdev->def->index, zmii_mode_name(dev->mode));
+ } else {
+ /* All inputs must use the same mode */
+ if (*mode != PHY_MODE_NA && *mode != dev->mode) {
+ printk(KERN_ERR
+ "zmii%d: invalid mode %d specified for input %d\n",
+ ocpdev->def->index, *mode, input);
+ return -EINVAL;
+ }
+ }
+
+ /* Report back correct PHY mode,
+ * it may be used during PHY initialization.
+ */
+ *mode = dev->mode;
+
+ /* Enable this input */
+ out_be32(&p->fer, in_be32(&p->fer) | zmii_mode_mask(dev->mode, input));
+ out:
+ ++dev->users;
+ return 0;
+}
+
+int __init zmii_attach(void *emac)
+{
+ struct ocp_enet_private *dev = emac;
+ struct ocp_func_emac_data *emacdata = dev->def->additions;
+
+ if (emacdata->zmii_idx >= 0) {
+ dev->zmii_input = emacdata->zmii_mux;
+ dev->zmii_dev =
+ ocp_find_device(OCP_VENDOR_IBM, OCP_FUNC_ZMII,
+ emacdata->zmii_idx);
+ if (!dev->zmii_dev) {
+ printk(KERN_ERR "emac%d: unknown zmii%d!\n",
+ dev->def->index, emacdata->zmii_idx);
+ return -ENODEV;
+ }
+ if (zmii_init
+ (dev->zmii_dev, dev->zmii_input, &emacdata->phy_mode)) {
+ printk(KERN_ERR
+ "emac%d: zmii%d initialization failed!\n",
+ dev->def->index, emacdata->zmii_idx);
+ return -ENODEV;
+ }
+ }
+ return 0;
+}
+
+void __zmii_enable_mdio(struct ocp_device *ocpdev, int input)
+{
+ struct ibm_ocp_zmii *dev = ocp_get_drvdata(ocpdev);
+ u32 fer = in_be32(&dev->base->fer) & ~ZMII_FER_MDI_ALL;
+
+ ZMII_DBG2("%d: mdio(%d)" NL, ocpdev->def->index, input);
+
+ out_be32(&dev->base->fer, fer | ZMII_FER_MDI(input));
+}
+
+void __zmii_set_speed(struct ocp_device *ocpdev, int input, int speed)
+{
+ struct ibm_ocp_zmii *dev = ocp_get_drvdata(ocpdev);
+ u32 ssr = in_be32(&dev->base->ssr);
+
+ ZMII_DBG("%d: speed(%d, %d)" NL, ocpdev->def->index, input, speed);
+
+ if (speed == SPEED_100)
+ ssr |= ZMII_SSR_SP(input);
+ else
+ ssr &= ~ZMII_SSR_SP(input);
+
+ out_be32(&dev->base->ssr, ssr);
+}
+
+void __exit __zmii_fini(struct ocp_device *ocpdev, int input)
+{
+ struct ibm_ocp_zmii *dev = ocp_get_drvdata(ocpdev);
+ BUG_ON(!dev || dev->users == 0);
+
+ ZMII_DBG("%d: fini(%d)" NL, ocpdev->def->index, input);
+
+ /* Disable this input */
+ out_be32(&dev->base->fer,
+ in_be32(&dev->base->fer) & ~zmii_mode_mask(dev->mode, input));
+
+ if (!--dev->users) {
+ /* Free everything if this is the last user */
+ ocp_set_drvdata(ocpdev, NULL);
+ iounmap((void *)dev->base);
+ kfree(dev);
+ }
+}
+
+int __zmii_get_regs_len(struct ocp_device *ocpdev)
+{
+ return sizeof(struct emac_ethtool_regs_subhdr) +
+ sizeof(struct zmii_regs);
+}
+
+void *zmii_dump_regs(struct ocp_device *ocpdev, void *buf)
+{
+ struct ibm_ocp_zmii *dev = ocp_get_drvdata(ocpdev);
+ struct emac_ethtool_regs_subhdr *hdr = buf;
+ struct zmii_regs *regs = (struct zmii_regs *)(hdr + 1);
+
+ hdr->version = 0;
+ hdr->index = ocpdev->def->index;
+ memcpy_fromio(regs, dev->base, sizeof(struct zmii_regs));
+ return regs + 1;
+}
/*
- * ocp_zmii.h
+ * drivers/net/ibm_emac/ibm_emac_zmii.h
*
- * Defines for the IBM ZMII bridge
+ * Driver for PowerPC 4xx on-chip ethernet controller, ZMII bridge support.
*
- * Armin Kuster akuster@mvista.com
- * Dec, 2001
+ * Copyright (c) 2004, 2005 Zultys Technologies.
+ * Eugene Surovegin <eugene.surovegin@zultys.com> or <ebs@ebshome.net>
*
- * Copyright 2001 MontaVista Softare Inc.
+ * Based on original work by
+ * Armin Kuster <akuster@mvista.com>
+ * Copyright 2001 MontaVista Softare Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
+ *
*/
-
#ifndef _IBM_EMAC_ZMII_H_
#define _IBM_EMAC_ZMII_H_
#include <linux/config.h>
+#include <linux/init.h>
+#include <asm/ocp.h>
/* ZMII bridge registers */
struct zmii_regs {
u32 smiirs; /* SMII status reg */
};
-#define ZMII_INPUTS 4
-
/* ZMII device */
struct ibm_ocp_zmii {
struct zmii_regs *base;
- int mode[ZMII_INPUTS];
+ int mode; /* subset of PHY_MODE_XXXX */
int users; /* number of EMACs using this ZMII bridge */
+ u32 fer_save; /* FER value left by firmware */
};
-/* Fuctional Enable Reg */
-
-#define ZMII_FER_MASK(x) (0xf0000000 >> (4*x))
-
-#define ZMII_MDI0 0x80000000
-#define ZMII_SMII0 0x40000000
-#define ZMII_RMII0 0x20000000
-#define ZMII_MII0 0x10000000
-#define ZMII_MDI1 0x08000000
-#define ZMII_SMII1 0x04000000
-#define ZMII_RMII1 0x02000000
-#define ZMII_MII1 0x01000000
-#define ZMII_MDI2 0x00800000
-#define ZMII_SMII2 0x00400000
-#define ZMII_RMII2 0x00200000
-#define ZMII_MII2 0x00100000
-#define ZMII_MDI3 0x00080000
-#define ZMII_SMII3 0x00040000
-#define ZMII_RMII3 0x00020000
-#define ZMII_MII3 0x00010000
+#ifdef CONFIG_IBM_EMAC_ZMII
+int zmii_attach(void *emac) __init;
-/* Speed Selection reg */
+void __zmii_fini(struct ocp_device *ocpdev, int input) __exit;
+static inline void zmii_fini(struct ocp_device *ocpdev, int input)
+{
+ if (ocpdev)
+ __zmii_fini(ocpdev, input);
+}
-#define ZMII_SCI0 0x40000000
-#define ZMII_FSS0 0x20000000
-#define ZMII_SP0 0x10000000
-#define ZMII_SCI1 0x04000000
-#define ZMII_FSS1 0x02000000
-#define ZMII_SP1 0x01000000
-#define ZMII_SCI2 0x00400000
-#define ZMII_FSS2 0x00200000
-#define ZMII_SP2 0x00100000
-#define ZMII_SCI3 0x00040000
-#define ZMII_FSS3 0x00020000
-#define ZMII_SP3 0x00010000
+void __zmii_enable_mdio(struct ocp_device *ocpdev, int input);
+static inline void zmii_enable_mdio(struct ocp_device *ocpdev, int input)
+{
+ if (ocpdev)
+ __zmii_enable_mdio(ocpdev, input);
+}
-#define ZMII_MII0_100MB ZMII_SP0
-#define ZMII_MII0_10MB ~ZMII_SP0
-#define ZMII_MII1_100MB ZMII_SP1
-#define ZMII_MII1_10MB ~ZMII_SP1
-#define ZMII_MII2_100MB ZMII_SP2
-#define ZMII_MII2_10MB ~ZMII_SP2
-#define ZMII_MII3_100MB ZMII_SP3
-#define ZMII_MII3_10MB ~ZMII_SP3
+void __zmii_set_speed(struct ocp_device *ocpdev, int input, int speed);
+static inline void zmii_set_speed(struct ocp_device *ocpdev, int input,
+ int speed)
+{
+ if (ocpdev)
+ __zmii_set_speed(ocpdev, input, speed);
+}
-/* SMII Status reg */
+int __zmii_get_regs_len(struct ocp_device *ocpdev);
+static inline int zmii_get_regs_len(struct ocp_device *ocpdev)
+{
+ return ocpdev ? __zmii_get_regs_len(ocpdev) : 0;
+}
-#define ZMII_STS0 0xFF000000 /* EMAC0 smii status mask */
-#define ZMII_STS1 0x00FF0000 /* EMAC1 smii status mask */
+void *zmii_dump_regs(struct ocp_device *ocpdev, void *buf);
-#define SMII 0
-#define RMII 1
-#define MII 2
-#define MDI 3
+#else
+# define zmii_attach(x) 0
+# define zmii_fini(x,y) ((void)0)
+# define zmii_enable_mdio(x,y) ((void)0)
+# define zmii_set_speed(x,y,z) ((void)0)
+# define zmii_get_regs_len(x) 0
+# define zmii_dump_regs(x,buf) (buf)
+#endif /* !CONFIG_IBM_EMAC_ZMII */
#endif /* _IBM_EMAC_ZMII_H_ */
projects / linux-2.6 / commitdiff