Patch to add core platform support for the PMC-Sierra MSP71xx devices.
Signed-off-by: Marc St-Jean <Marc_St-Jean@pmc-sierra.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
--- /dev/null
+#
+# Makefile for the PMC-Sierra MSP SOCs
+#
+obj-y += msp_prom.o msp_setup.o msp_irq.o \
+ msp_time.o msp_serial.o msp_elb.o
+obj-$(CONFIG_PMC_MSP7120_GW) += msp_hwbutton.o
+obj-$(CONFIG_IRQ_MSP_SLP) += msp_irq_slp.o
+obj-$(CONFIG_IRQ_MSP_CIC) += msp_irq_cic.o
+obj-$(CONFIG_PCI) += msp_pci.o
+obj-$(CONFIG_MSPETH) += msp_eth.o
+obj-$(CONFIG_USB_MSP71XX) += msp_usb.o
--- /dev/null
+/*
+ * Sets up the proper Chip Select configuration registers. It is assumed that
+ * PMON sets up the ADDR and MASK registers properly.
+ *
+ * Copyright 2005-2006 PMC-Sierra, Inc.
+ * Author: Marc St-Jean, Marc_St-Jean@pmc-sierra.com
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
+ * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
+ * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
+ * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <msp_regs.h>
+
+static int __init msp_elb_setup(void)
+{
+#if defined(CONFIG_PMC_MSP7120_GW) \
+ || defined(CONFIG_PMC_MSP7120_EVAL)
+ /*
+ * Force all CNFG to be identical and equal to CS0,
+ * according to OPS doc
+ */
+ *CS1_CNFG_REG = *CS2_CNFG_REG = *CS3_CNFG_REG = *CS0_CNFG_REG;
+#endif
+ return 0;
+}
+
+subsys_initcall(msp_elb_setup);
--- /dev/null
+/*
+ * Sets up interrupt handlers for various hardware switches which are
+ * connected to interrupt lines.
+ *
+ * Copyright 2005-2207 PMC-Sierra, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
+ * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
+ * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
+ * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+
+#include <msp_int.h>
+#include <msp_regs.h>
+#include <msp_regops.h>
+#ifdef CONFIG_PMCTWILED
+#include <msp_led_macros.h>
+#endif
+
+/* For hwbutton_interrupt->initial_state */
+#define HWBUTTON_HI 0x1
+#define HWBUTTON_LO 0x2
+
+/*
+ * This struct describes a hardware button
+ */
+struct hwbutton_interrupt {
+ char *name; /* Name of button */
+ int irq; /* Actual LINUX IRQ */
+ int eirq; /* Extended IRQ number (0-7) */
+ int initial_state; /* The "normal" state of the switch */
+ void (*handle_hi)(void *); /* Handler: switch input has gone HI */
+ void (*handle_lo)(void *); /* Handler: switch input has gone LO */
+ void *data; /* Optional data to pass to handler */
+};
+
+#ifdef CONFIG_PMC_MSP7120_GW
+extern void msp_restart(char *);
+
+static void softreset_push(void *data)
+{
+ printk(KERN_WARNING "SOFTRESET switch was pushed\n");
+
+ /*
+ * In the future you could move this to the release handler,
+ * timing the difference between the 'push' and 'release', and only
+ * doing this ungraceful restart if the button has been down for
+ * a certain amount of time; otherwise doing a graceful restart.
+ */
+
+ msp_restart(NULL);
+}
+
+static void softreset_release(void *data)
+{
+ printk(KERN_WARNING "SOFTRESET switch was released\n");
+
+ /* Do nothing */
+}
+
+static void standby_on(void *data)
+{
+ printk(KERN_WARNING "STANDBY switch was set to ON (not implemented)\n");
+
+ /* TODO: Put board in standby mode */
+#ifdef CONFIG_PMCTWILED
+ msp_led_turn_off(MSP_LED_PWRSTANDBY_GREEN);
+ msp_led_turn_on(MSP_LED_PWRSTANDBY_RED);
+#endif
+}
+
+static void standby_off(void *data)
+{
+ printk(KERN_WARNING
+ "STANDBY switch was set to OFF (not implemented)\n");
+
+ /* TODO: Take out of standby mode */
+#ifdef CONFIG_PMCTWILED
+ msp_led_turn_on(MSP_LED_PWRSTANDBY_GREEN);
+ msp_led_turn_off(MSP_LED_PWRSTANDBY_RED);
+#endif
+}
+
+static struct hwbutton_interrupt softreset_sw = {
+ .name = "Softreset button",
+ .irq = MSP_INT_EXT0,
+ .eirq = 0,
+ .initial_state = HWBUTTON_HI,
+ .handle_hi = softreset_release,
+ .handle_lo = softreset_push,
+ .data = NULL,
+};
+
+static struct hwbutton_interrupt standby_sw = {
+ .name = "Standby switch",
+ .irq = MSP_INT_EXT1,
+ .eirq = 1,
+ .initial_state = HWBUTTON_HI,
+ .handle_hi = standby_off,
+ .handle_lo = standby_on,
+ .data = NULL,
+};
+#endif /* CONFIG_PMC_MSP7120_GW */
+
+static irqreturn_t hwbutton_handler(int irq, void *data)
+{
+ struct hwbutton_interrupt *hirq = data;
+ unsigned long cic_ext = *CIC_EXT_CFG_REG;
+
+ if (irq != hirq->irq)
+ return IRQ_NONE;
+
+ if (CIC_EXT_IS_ACTIVE_HI(cic_ext, hirq->eirq)) {
+ /* Interrupt: pin is now HI */
+ CIC_EXT_SET_ACTIVE_LO(cic_ext, hirq->eirq);
+ hirq->handle_hi(hirq->data);
+ } else {
+ /* Interrupt: pin is now LO */
+ CIC_EXT_SET_ACTIVE_HI(cic_ext, hirq->eirq);
+ hirq->handle_lo(hirq->data);
+ }
+
+ /*
+ * Invert the POLARITY of this level interrupt to ack the interrupt
+ * Thus next state change will invoke the opposite message
+ */
+ *CIC_EXT_CFG_REG = cic_ext;
+
+ return IRQ_HANDLED;
+}
+
+static int msp_hwbutton_register(struct hwbutton_interrupt *hirq)
+{
+ unsigned long cic_ext;
+
+ if (hirq->handle_hi == NULL || hirq->handle_lo == NULL)
+ return -EINVAL;
+
+ cic_ext = *CIC_EXT_CFG_REG;
+ CIC_EXT_SET_TRIGGER_LEVEL(cic_ext, hirq->eirq);
+ if (hirq->initial_state == HWBUTTON_HI)
+ CIC_EXT_SET_ACTIVE_LO(cic_ext, hirq->eirq);
+ else
+ CIC_EXT_SET_ACTIVE_HI(cic_ext, hirq->eirq);
+ *CIC_EXT_CFG_REG = cic_ext;
+
+ return request_irq(hirq->irq, hwbutton_handler, SA_INTERRUPT,
+ hirq->name, (void *)hirq);
+}
+
+static int __init msp_hwbutton_setup(void)
+{
+#ifdef CONFIG_PMC_MSP7120_GW
+ msp_hwbutton_register(&softreset_sw);
+ msp_hwbutton_register(&standby_sw);
+#endif
+ return 0;
+}
+
+subsys_initcall(msp_hwbutton_setup);
--- /dev/null
+/*
+ * IRQ vector handles
+ *
+ * Copyright (C) 1995, 1996, 1997, 2003 by Ralf Baechle
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/irq.h>
+#include <linux/interrupt.h>
+#include <linux/ptrace.h>
+#include <linux/time.h>
+
+#include <asm/irq_cpu.h>
+
+#include <msp_int.h>
+
+extern void msp_int_handle(void);
+
+/* SLP bases systems */
+extern void msp_slp_irq_init(void);
+extern void msp_slp_irq_dispatch(void);
+
+/* CIC based systems */
+extern void msp_cic_irq_init(void);
+extern void msp_cic_irq_dispatch(void);
+
+/*
+ * The PMC-Sierra MSP interrupts are arranged in a 3 level cascaded
+ * hierarchical system. The first level are the direct MIPS interrupts
+ * and are assigned the interrupt range 0-7. The second level is the SLM
+ * interrupt controller and is assigned the range 8-39. The third level
+ * comprises the Peripherial block, the PCI block, the PCI MSI block and
+ * the SLP. The PCI interrupts and the SLP errors are handled by the
+ * relevant subsystems so the core interrupt code needs only concern
+ * itself with the Peripheral block. These are assigned interrupts in
+ * the range 40-71.
+ */
+
+asmlinkage void plat_irq_dispatch(struct pt_regs *regs)
+{
+ u32 pending;
+
+ pending = read_c0_status() & read_c0_cause();
+
+ /*
+ * jump to the correct interrupt routine
+ * These are arranged in priority order and the timer
+ * comes first!
+ */
+
+#ifdef CONFIG_IRQ_MSP_CIC /* break out the CIC stuff for now */
+ if (pending & C_IRQ4) /* do the peripherals first, that's the timer */
+ msp_cic_irq_dispatch();
+
+ else if (pending & C_IRQ0)
+ do_IRQ(MSP_INT_MAC0);
+
+ else if (pending & C_IRQ1)
+ do_IRQ(MSP_INT_MAC1);
+
+ else if (pending & C_IRQ2)
+ do_IRQ(MSP_INT_USB);
+
+ else if (pending & C_IRQ3)
+ do_IRQ(MSP_INT_SAR);
+
+ else if (pending & C_IRQ5)
+ do_IRQ(MSP_INT_SEC);
+
+#else
+ if (pending & C_IRQ5)
+ do_IRQ(MSP_INT_TIMER);
+
+ else if (pending & C_IRQ0)
+ do_IRQ(MSP_INT_MAC0);
+
+ else if (pending & C_IRQ1)
+ do_IRQ(MSP_INT_MAC1);
+
+ else if (pending & C_IRQ3)
+ do_IRQ(MSP_INT_VE);
+
+ else if (pending & C_IRQ4)
+ msp_slp_irq_dispatch();
+#endif
+
+ else if (pending & C_SW0) /* do software after hardware */
+ do_IRQ(MSP_INT_SW0);
+
+ else if (pending & C_SW1)
+ do_IRQ(MSP_INT_SW1);
+}
+
+static struct irqaction cascade_msp = {
+ .handler = no_action,
+ .name = "MSP cascade"
+};
+
+
+void __init arch_init_irq(void)
+{
+ /* initialize the 1st-level CPU based interrupt controller */
+ mips_cpu_irq_init();
+
+#ifdef CONFIG_IRQ_MSP_CIC
+ msp_cic_irq_init();
+
+ /* setup the cascaded interrupts */
+ setup_irq(MSP_INT_CIC, &cascade_msp);
+ setup_irq(MSP_INT_PER, &cascade_msp);
+#else
+ /* setup the 2nd-level SLP register based interrupt controller */
+ msp_slp_irq_init();
+
+ /* setup the cascaded SLP/PER interrupts */
+ setup_irq(MSP_INT_SLP, &cascade_msp);
+ setup_irq(MSP_INT_PER, &cascade_msp);
+#endif
+}
--- /dev/null
+/*
+ * This file define the irq handler for MSP SLM subsystem interrupts.
+ *
+ * Copyright 2005-2007 PMC-Sierra, Inc, derived from irq_cpu.c
+ * Author: Andrew Hughes, Andrew_Hughes@pmc-sierra.com
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/bitops.h>
+
+#include <asm/system.h>
+
+#include <msp_cic_int.h>
+#include <msp_regs.h>
+
+/*
+ * NOTE: We are only enabling support for VPE0 right now.
+ */
+
+static inline void unmask_msp_cic_irq(unsigned int irq)
+{
+
+ /* check for PER interrupt range */
+ if (irq < MSP_PER_INTBASE)
+ *CIC_VPE0_MSK_REG |= (1 << (irq - MSP_CIC_INTBASE));
+ else
+ *PER_INT_MSK_REG |= (1 << (irq - MSP_PER_INTBASE));
+}
+
+static inline void mask_msp_cic_irq(unsigned int irq)
+{
+ /* check for PER interrupt range */
+ if (irq < MSP_PER_INTBASE)
+ *CIC_VPE0_MSK_REG &= ~(1 << (irq - MSP_CIC_INTBASE));
+ else
+ *PER_INT_MSK_REG &= ~(1 << (irq - MSP_PER_INTBASE));
+}
+
+/*
+ * While we ack the interrupt interrupts are disabled and thus we don't need
+ * to deal with concurrency issues. Same for msp_cic_irq_end.
+ */
+static inline void ack_msp_cic_irq(unsigned int irq)
+{
+ mask_msp_cic_irq(irq);
+
+ /*
+ * only really necessary for 18, 16-14 and sometimes 3:0 (since
+ * these can be edge sensitive) but it doesn't hurt for the others.
+ */
+
+ /* check for PER interrupt range */
+ if (irq < MSP_PER_INTBASE)
+ *CIC_STS_REG = (1 << (irq - MSP_CIC_INTBASE));
+ else
+ *PER_INT_STS_REG = (1 << (irq - MSP_PER_INTBASE));
+}
+
+static struct irq_chip msp_cic_irq_controller = {
+ .name = "MSP_CIC",
+ .ack = ack_msp_cic_irq,
+ .mask = ack_msp_cic_irq,
+ .mask_ack = ack_msp_cic_irq,
+ .unmask = unmask_msp_cic_irq,
+};
+
+
+void __init msp_cic_irq_init(void)
+{
+ int i;
+
+ /* Mask/clear interrupts. */
+ *CIC_VPE0_MSK_REG = 0x00000000;
+ *PER_INT_MSK_REG = 0x00000000;
+ *CIC_STS_REG = 0xFFFFFFFF;
+ *PER_INT_STS_REG = 0xFFFFFFFF;
+
+#if defined(CONFIG_PMC_MSP7120_GW) || \
+ defined(CONFIG_PMC_MSP7120_EVAL)
+ /*
+ * The MSP7120 RG and EVBD boards use IRQ[6:4] for PCI.
+ * These inputs map to EXT_INT_POL[6:4] inside the CIC.
+ * They are to be active low, level sensitive.
+ */
+ *CIC_EXT_CFG_REG &= 0xFFFF8F8F;
+#endif
+
+ /* initialize all the IRQ descriptors */
+ for (i = MSP_CIC_INTBASE; i < MSP_PER_INTBASE + 32; i++)
+ set_irq_chip_and_handler(i, &msp_cic_irq_controller,
+ handle_level_irq);
+}
+
+void msp_cic_irq_dispatch(void)
+{
+ u32 pending;
+ int intbase;
+
+ intbase = MSP_CIC_INTBASE;
+ pending = *CIC_STS_REG & *CIC_VPE0_MSK_REG;
+
+ /* check for PER interrupt */
+ if (pending == (1 << (MSP_INT_PER - MSP_CIC_INTBASE))) {
+ intbase = MSP_PER_INTBASE;
+ pending = *PER_INT_STS_REG & *PER_INT_MSK_REG;
+ }
+
+ /* check for spurious interrupt */
+ if (pending == 0x00000000) {
+ printk(KERN_ERR
+ "Spurious %s interrupt? status %08x, mask %08x\n",
+ (intbase == MSP_CIC_INTBASE) ? "CIC" : "PER",
+ (intbase == MSP_CIC_INTBASE) ?
+ *CIC_STS_REG : *PER_INT_STS_REG,
+ (intbase == MSP_CIC_INTBASE) ?
+ *CIC_VPE0_MSK_REG : *PER_INT_MSK_REG);
+ return;
+ }
+
+ /* check for the timer and dispatch it first */
+ if ((intbase == MSP_CIC_INTBASE) &&
+ (pending & (1 << (MSP_INT_VPE0_TIMER - MSP_CIC_INTBASE))))
+ do_IRQ(MSP_INT_VPE0_TIMER);
+ else
+ do_IRQ(ffs(pending) + intbase - 1);
+}
+
--- /dev/null
+/*
+ * This file define the irq handler for MSP SLM subsystem interrupts.
+ *
+ * Copyright 2005-2006 PMC-Sierra, Inc, derived from irq_cpu.c
+ * Author: Andrew Hughes, Andrew_Hughes@pmc-sierra.com
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/bitops.h>
+
+#include <asm/mipsregs.h>
+#include <asm/system.h>
+
+#include <msp_slp_int.h>
+#include <msp_regs.h>
+
+static inline void unmask_msp_slp_irq(unsigned int irq)
+{
+ /* check for PER interrupt range */
+ if (irq < MSP_PER_INTBASE)
+ *SLP_INT_MSK_REG |= (1 << (irq - MSP_SLP_INTBASE));
+ else
+ *PER_INT_MSK_REG |= (1 << (irq - MSP_PER_INTBASE));
+}
+
+static inline void mask_msp_slp_irq(unsigned int irq)
+{
+ /* check for PER interrupt range */
+ if (irq < MSP_PER_INTBASE)
+ *SLP_INT_MSK_REG &= ~(1 << (irq - MSP_SLP_INTBASE));
+ else
+ *PER_INT_MSK_REG &= ~(1 << (irq - MSP_PER_INTBASE));
+}
+
+/*
+ * While we ack the interrupt interrupts are disabled and thus we don't need
+ * to deal with concurrency issues. Same for msp_slp_irq_end.
+ */
+static inline void ack_msp_slp_irq(unsigned int irq)
+{
+ mask_slp_irq(irq);
+
+ /*
+ * only really necessary for 18, 16-14 and sometimes 3:0 (since
+ * these can be edge sensitive) but it doesn't hurt for the others.
+ */
+
+ /* check for PER interrupt range */
+ if (irq < MSP_PER_INTBASE)
+ *SLP_INT_STS_REG = (1 << (irq - MSP_SLP_INTBASE));
+ else
+ *PER_INT_STS_REG = (1 << (irq - MSP_PER_INTBASE));
+}
+
+static struct irq_chip msp_slp_irq_controller = {
+ .name = "MSP_SLP",
+ .ack = ack_msp_slp_irq,
+ .mask = ack_msp_slp_irq,
+ .mask_ack = ack_msp_slp_irq,
+ .unmask = unmask_msp_slp_irq,
+};
+
+void __init msp_slp_irq_init(void)
+{
+ int i;
+
+ /* Mask/clear interrupts. */
+ *SLP_INT_MSK_REG = 0x00000000;
+ *PER_INT_MSK_REG = 0x00000000;
+ *SLP_INT_STS_REG = 0xFFFFFFFF;
+ *PER_INT_STS_REG = 0xFFFFFFFF;
+
+ /* initialize all the IRQ descriptors */
+ for (i = MSP_SLP_INTBASE; i < MSP_PER_INTBASE + 32; i++)
+ set_irq_chip_and_handler(i, &msp_slp_irq_controller
+ handle_level_irq);
+}
+
+void msp_slp_irq_dispatch(void)
+{
+ u32 pending;
+ int intbase;
+
+ intbase = MSP_SLP_INTBASE;
+ pending = *SLP_INT_STS_REG & *SLP_INT_MSK_REG;
+
+ /* check for PER interrupt */
+ if (pending == (1 << (MSP_INT_PER - MSP_SLP_INTBASE))) {
+ intbase = MSP_PER_INTBASE;
+ pending = *PER_INT_STS_REG & *PER_INT_MSK_REG;
+ }
+
+ /* check for spurious interrupt */
+ if (pending == 0x00000000) {
+ printk(KERN_ERR "Spurious %s interrupt?\n",
+ (intbase == MSP_SLP_INTBASE) ? "SLP" : "PER");
+ return;
+ }
+
+ /* dispatch the irq */
+ do_IRQ(ffs(pending) + intbase - 1);
+}
--- /dev/null
+/*
+ * BRIEF MODULE DESCRIPTION
+ * PROM library initialisation code, assuming a version of
+ * pmon is the boot code.
+ *
+ * Copyright 2000,2001 MontaVista Software Inc.
+ * Author: MontaVista Software, Inc.
+ * ppopov@mvista.com or source@mvista.com
+ *
+ * This file was derived from Carsten Langgaard's
+ * arch/mips/mips-boards/xx files.
+ *
+ * Carsten Langgaard, carstenl@mips.com
+ * Copyright (C) 1999,2000 MIPS Technologies, Inc. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
+ * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
+ * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
+ * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/string.h>
+#include <linux/interrupt.h>
+#include <linux/mm.h>
+#ifdef CONFIG_CRAMFS
+#include <linux/cramfs_fs.h>
+#endif
+#ifdef CONFIG_SQUASHFS
+#include <linux/squashfs_fs.h>
+#endif
+
+#include <asm/addrspace.h>
+#include <asm/bootinfo.h>
+#include <asm-generic/sections.h>
+#include <asm/page.h>
+
+#include <msp_prom.h>
+#include <msp_regs.h>
+
+/* global PROM environment variables and pointers */
+int prom_argc;
+char **prom_argv, **prom_envp;
+int *prom_vec;
+
+/* debug flag */
+int init_debug = 1;
+
+/* memory blocks */
+struct prom_pmemblock mdesc[PROM_MAX_PMEMBLOCKS];
+
+/* default feature sets */
+static char msp_default_features[] =
+#if defined(CONFIG_PMC_MSP4200_EVAL) \
+ || defined(CONFIG_PMC_MSP4200_GW)
+ "ERER";
+#elif defined(CONFIG_PMC_MSP7120_EVAL) \
+ || defined(CONFIG_PMC_MSP7120_GW)
+ "EMEMSP";
+#elif defined(CONFIG_PMC_MSP7120_FPGA)
+ "EMEM";
+#endif
+
+/* conversion functions */
+static inline unsigned char str2hexnum(unsigned char c)
+{
+ if (c >= '0' && c <= '9')
+ return c - '0';
+ if (c >= 'a' && c <= 'f')
+ return c - 'a' + 10;
+ return 0; /* foo */
+}
+
+static inline int str2eaddr(unsigned char *ea, unsigned char *str)
+{
+ int index = 0;
+ unsigned char num = 0;
+
+ while (*str != '\0') {
+ if ((*str == '.') || (*str == ':')) {
+ ea[index++] = num;
+ num = 0;
+ str++;
+ } else {
+ num = num << 4;
+ num |= str2hexnum(*str++);
+ }
+ }
+
+ if (index == 5) {
+ ea[index++] = num;
+ return 0;
+ } else
+ return -1;
+}
+EXPORT_SYMBOL(str2eaddr);
+
+static inline unsigned long str2hex(unsigned char *str)
+{
+ int value = 0;
+
+ while (*str) {
+ value = value << 4;
+ value |= str2hexnum(*str++);
+ }
+
+ return value;
+}
+
+/* function to query the system information */
+const char *get_system_type(void)
+{
+#if defined(CONFIG_PMC_MSP4200_EVAL)
+ return "PMC-Sierra MSP4200 Eval Board";
+#elif defined(CONFIG_PMC_MSP4200_GW)
+ return "PMC-Sierra MSP4200 VoIP Gateway";
+#elif defined(CONFIG_PMC_MSP7120_EVAL)
+ return "PMC-Sierra MSP7120 Eval Board";
+#elif defined(CONFIG_PMC_MSP7120_GW)
+ return "PMC-Sierra MSP7120 Residential Gateway";
+#elif defined(CONFIG_PMC_MSP7120_FPGA)
+ return "PMC-Sierra MSP7120 FPGA";
+#else
+ #error "What is the type of *your* MSP?"
+#endif
+}
+
+int get_ethernet_addr(char *ethaddr_name, char *ethernet_addr)
+{
+ char *ethaddr_str;
+
+ ethaddr_str = prom_getenv(ethaddr_name);
+ if (!ethaddr_str) {
+ printk(KERN_WARNING "%s not set in boot prom\n", ethaddr_name);
+ return -1;
+ }
+
+ if (str2eaddr(ethernet_addr, ethaddr_str) == -1) {
+ printk(KERN_WARNING "%s badly formatted-<%s>\n",
+ ethaddr_name, ethaddr_str);
+ return -1;
+ }
+
+ if (init_debug > 1) {
+ int i;
+ printk(KERN_DEBUG "get_ethernet_addr: for %s ", ethaddr_name);
+ for (i = 0; i < 5; i++)
+ printk(KERN_DEBUG "%02x:",
+ (unsigned char)*(ethernet_addr+i));
+ printk(KERN_DEBUG "%02x\n", *(ethernet_addr+i));
+ }
+
+ return 0;
+}
+EXPORT_SYMBOL(get_ethernet_addr);
+
+static char *get_features(void)
+{
+ char *feature = prom_getenv(FEATURES);
+
+ if (feature == NULL) {
+ /* default features based on MACHINE_TYPE */
+ feature = msp_default_features;
+ }
+
+ return feature;
+}
+
+static char test_feature(char c)
+{
+ char *feature = get_features();
+
+ while (*feature) {
+ if (*feature++ == c)
+ return *feature;
+ feature++;
+ }
+
+ return FEATURE_NOEXIST;
+}
+
+unsigned long get_deviceid(void)
+{
+ char *deviceid = prom_getenv(DEVICEID);
+
+ if (deviceid == NULL)
+ return *DEV_ID_REG;
+ else
+ return str2hex(deviceid);
+}
+
+char identify_pci(void)
+{
+ return test_feature(PCI_KEY);
+}
+EXPORT_SYMBOL(identify_pci);
+
+char identify_pcimux(void)
+{
+ return test_feature(PCIMUX_KEY);
+}
+
+char identify_sec(void)
+{
+ return test_feature(SEC_KEY);
+}
+EXPORT_SYMBOL(identify_sec);
+
+char identify_spad(void)
+{
+ return test_feature(SPAD_KEY);
+}
+EXPORT_SYMBOL(identify_spad);
+
+char identify_tdm(void)
+{
+ return test_feature(TDM_KEY);
+}
+EXPORT_SYMBOL(identify_tdm);
+
+char identify_zsp(void)
+{
+ return test_feature(ZSP_KEY);
+}
+EXPORT_SYMBOL(identify_zsp);
+
+static char identify_enetfeature(char key, unsigned long interface_num)
+{
+ char *feature = get_features();
+
+ while (*feature) {
+ if (*feature++ == key && interface_num-- == 0)
+ return *feature;
+ feature++;
+ }
+
+ return FEATURE_NOEXIST;
+}
+
+char identify_enet(unsigned long interface_num)
+{
+ return identify_enetfeature(ENET_KEY, interface_num);
+}
+EXPORT_SYMBOL(identify_enet);
+
+char identify_enetTxD(unsigned long interface_num)
+{
+ return identify_enetfeature(ENETTXD_KEY, interface_num);
+}
+EXPORT_SYMBOL(identify_enetTxD);
+
+unsigned long identify_family(void)
+{
+ unsigned long deviceid;
+
+ deviceid = get_deviceid();
+
+ return deviceid & CPU_DEVID_FAMILY;
+}
+EXPORT_SYMBOL(identify_family);
+
+unsigned long identify_revision(void)
+{
+ unsigned long deviceid;
+
+ deviceid = get_deviceid();
+
+ return deviceid & CPU_DEVID_REVISION;
+}
+EXPORT_SYMBOL(identify_revision);
+
+/* PROM environment functions */
+char *prom_getenv(char *env_name)
+{
+ /*
+ * Return a pointer to the given environment variable. prom_envp
+ * points to a null terminated array of pointers to variables.
+ * Environment variables are stored in the form of "memsize=64"
+ */
+
+ char **var = prom_envp;
+ int i = strlen(env_name);
+
+ while (*var) {
+ if (strncmp(env_name, *var, i) == 0) {
+ return (*var + strlen(env_name) + 1);
+ }
+ var++;
+ }
+
+ return NULL;
+}
+
+/* PROM commandline functions */
+char *prom_getcmdline(void)
+{
+ return &(arcs_cmdline[0]);
+}
+EXPORT_SYMBOL(prom_getcmdline);
+
+void __init prom_init_cmdline(void)
+{
+ char *cp;
+ int actr;
+
+ actr = 1; /* Always ignore argv[0] */
+
+ cp = &(arcs_cmdline[0]);
+ while (actr < prom_argc) {
+ strcpy(cp, prom_argv[actr]);
+ cp += strlen(prom_argv[actr]);
+ *cp++ = ' ';
+ actr++;
+ }
+ if (cp != &(arcs_cmdline[0])) /* get rid of trailing space */
+ --cp;
+ *cp = '\0';
+}
+
+/* memory allocation functions */
+static int __init prom_memtype_classify(unsigned int type)
+{
+ switch (type) {
+ case yamon_free:
+ return BOOT_MEM_RAM;
+ case yamon_prom:
+ return BOOT_MEM_ROM_DATA;
+ default:
+ return BOOT_MEM_RESERVED;
+ }
+}
+
+void __init prom_meminit(void)
+{
+ struct prom_pmemblock *p;
+
+ p = prom_getmdesc();
+
+ while (p->size) {
+ long type;
+ unsigned long base, size;
+
+ type = prom_memtype_classify(p->type);
+ base = p->base;
+ size = p->size;
+
+ add_memory_region(base, size, type);
+ p++;
+ }
+}
+
+void __init prom_free_prom_memory(void)
+{
+ int argc;
+ char **argv;
+ char **envp;
+ char *ptr;
+ int len = 0;
+ int i;
+ unsigned long addr;
+
+ /*
+ * preserve environment variables and command line from pmon/bbload
+ * first preserve the command line
+ */
+ for (argc = 0; argc < prom_argc; argc++) {
+ len += sizeof(char *); /* length of pointer */
+ len += strlen(prom_argv[argc]) + 1; /* length of string */
+ }
+ len += sizeof(char *); /* plus length of null pointer */
+
+ argv = kmalloc(len, GFP_KERNEL);
+ ptr = (char *) &argv[prom_argc + 1]; /* strings follow array */
+
+ for (argc = 0; argc < prom_argc; argc++) {
+ argv[argc] = ptr;
+ strcpy(ptr, prom_argv[argc]);
+ ptr += strlen(prom_argv[argc]) + 1;
+ }
+ argv[prom_argc] = NULL; /* end array with null pointer */
+ prom_argv = argv;
+
+ /* next preserve the environment variables */
+ len = 0;
+ i = 0;
+ for (envp = prom_envp; *envp != NULL; envp++) {
+ i++; /* count number of environment variables */
+ len += sizeof(char *); /* length of pointer */
+ len += strlen(*envp) + 1; /* length of string */
+ }
+ len += sizeof(char *); /* plus length of null pointer */
+
+ envp = kmalloc(len, GFP_KERNEL);
+ ptr = (char *) &envp[i+1];
+
+ for (argc = 0; argc < i; argc++) {
+ envp[argc] = ptr;
+ strcpy(ptr, prom_envp[argc]);
+ ptr += strlen(prom_envp[argc]) + 1;
+ }
+ envp[i] = NULL; /* end array with null pointer */
+ prom_envp = envp;
+
+ for (i = 0; i < boot_mem_map.nr_map; i++) {
+ if (boot_mem_map.map[i].type != BOOT_MEM_ROM_DATA)
+ continue;
+
+ addr = boot_mem_map.map[i].addr;
+ free_init_pages("prom memory",
+ addr, addr + boot_mem_map.map[i].size);
+ }
+}
+
+struct prom_pmemblock *__init prom_getmdesc(void)
+{
+ static char memsz_env[] __initdata = "memsize";
+ static char heaptop_env[] __initdata = "heaptop";
+ char *str;
+ unsigned int memsize;
+ unsigned int heaptop;
+#ifdef CONFIG_MTD_PMC_MSP_RAMROOT
+ void *ramroot_start;
+ unsigned long ramroot_size;
+#endif
+ int i;
+
+ str = prom_getenv(memsz_env);
+ if (!str) {
+ ppfinit("memsize not set in boot prom, "
+ "set to default (32Mb)\n");
+ memsize = 0x02000000;
+ } else {
+ memsize = simple_strtol(str, NULL, 0);
+
+ if (memsize == 0) {
+ /* if memsize is a bad size, use reasonable default */
+ memsize = 0x02000000;
+ }
+
+ /* convert to physical address (removing caching bits, etc) */
+ memsize = CPHYSADDR(memsize);
+ }
+
+ str = prom_getenv(heaptop_env);
+ if (!str) {
+ heaptop = CPHYSADDR((u32)&_text);
+ ppfinit("heaptop not set in boot prom, "
+ "set to default 0x%08x\n", heaptop);
+ } else {
+ heaptop = simple_strtol(str, NULL, 16);
+ if (heaptop == 0) {
+ /* heaptop conversion bad, might have 0xValue */
+ heaptop = simple_strtol(str, NULL, 0);
+
+ if (heaptop == 0) {
+ /* heaptop still bad, use reasonable default */
+ heaptop = CPHYSADDR((u32)&_text);
+ }
+ }
+
+ /* convert to physical address (removing caching bits, etc) */
+ heaptop = CPHYSADDR((u32)heaptop);
+ }
+
+ /* the base region */
+ i = 0;
+ mdesc[i].type = BOOT_MEM_RESERVED;
+ mdesc[i].base = 0x00000000;
+ mdesc[i].size = PAGE_ALIGN(0x300 + 0x80);
+ /* jtag interrupt vector + sizeof vector */
+
+ /* PMON data */
+ if (heaptop > mdesc[i].base + mdesc[i].size) {
+ i++; /* 1 */
+ mdesc[i].type = BOOT_MEM_ROM_DATA;
+ mdesc[i].base = mdesc[i-1].base + mdesc[i-1].size;
+ mdesc[i].size = heaptop - mdesc[i].base;
+ }
+
+ /* end of PMON data to start of kernel -- probably zero .. */
+ if (heaptop != CPHYSADDR((u32)_text)) {
+ i++; /* 2 */
+ mdesc[i].type = BOOT_MEM_RAM;
+ mdesc[i].base = heaptop;
+ mdesc[i].size = CPHYSADDR((u32)_text) - mdesc[i].base;
+ }
+
+ /* kernel proper */
+ i++; /* 3 */
+ mdesc[i].type = BOOT_MEM_RESERVED;
+ mdesc[i].base = CPHYSADDR((u32)_text);
+#ifdef CONFIG_MTD_PMC_MSP_RAMROOT
+ if (get_ramroot(&ramroot_start, &ramroot_size)) {
+ /*
+ * Rootfs in RAM -- follows kernel
+ * Combine rootfs image with kernel block so a
+ * page (4k) isn't wasted between memory blocks
+ */
+ mdesc[i].size = CPHYSADDR(PAGE_ALIGN(
+ (u32)ramroot_start + ramroot_size)) - mdesc[i].base;
+ } else
+#endif
+ mdesc[i].size = CPHYSADDR(PAGE_ALIGN(
+ (u32)_end)) - mdesc[i].base;
+
+ /* Remainder of RAM -- under memsize */
+ i++; /* 5 */
+ mdesc[i].type = yamon_free;
+ mdesc[i].base = mdesc[i-1].base + mdesc[i-1].size;
+ mdesc[i].size = memsize - mdesc[i].base;
+
+ return &mdesc[0];
+}
+
+/* rootfs functions */
+#ifdef CONFIG_MTD_PMC_MSP_RAMROOT
+bool get_ramroot(void **start, unsigned long *size)
+{
+ extern char _end[];
+
+ /* Check for start following the end of the kernel */
+ void *check_start = (void *)_end;
+
+ /* Check for supported rootfs types */
+#ifdef CONFIG_CRAMFS
+ if (*(__u32 *)check_start == CRAMFS_MAGIC) {
+ /* Get CRAMFS size */
+ *start = check_start;
+ *size = PAGE_ALIGN(((struct cramfs_super *)
+ check_start)->size);
+
+ return true;
+ }
+#endif
+#ifdef CONFIG_SQUASHFS
+ if (*((unsigned int *)check_start) == SQUASHFS_MAGIC) {
+ /* Get SQUASHFS size */
+ *start = check_start;
+ *size = PAGE_ALIGN(((struct squashfs_super_block *)
+ check_start)->bytes_used);
+
+ return true;
+ }
+#endif
+
+ return false;
+}
+EXPORT_SYMBOL(get_ramroot);
+#endif
--- /dev/null
+/*
+ * The generic setup file for PMC-Sierra MSP processors
+ *
+ * Copyright 2005-2007 PMC-Sierra, Inc,
+ * Author: Jun Sun, jsun@mvista.com or jsun@junsun.net
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <asm/bootinfo.h>
+#include <asm/cacheflush.h>
+#include <asm/r4kcache.h>
+#include <asm/reboot.h>
+#include <asm/time.h>
+
+#include <msp_prom.h>
+#include <msp_regs.h>
+
+#if defined(CONFIG_PMC_MSP7120_GW)
+#include <msp_regops.h>
+#include <msp_gpio.h>
+#define MSP_BOARD_RESET_GPIO 9
+#endif
+
+extern void msp_timer_init(void);
+extern void msp_serial_setup(void);
+extern void pmctwiled_setup(void);
+
+#if defined(CONFIG_PMC_MSP7120_EVAL) || \
+ defined(CONFIG_PMC_MSP7120_GW) || \
+ defined(CONFIG_PMC_MSP7120_FPGA)
+/*
+ * Performs the reset for MSP7120-based boards
+ */
+void msp7120_reset(void)
+{
+ void *start, *end, *iptr;
+ register int i;
+
+ /* Diasble all interrupts */
+ local_irq_disable();
+#ifdef CONFIG_SYS_SUPPORTS_MULTITHREADING
+ dvpe();
+#endif
+
+ /* Cache the reset code of this function */
+ __asm__ __volatile__ (
+ " .set push \n"
+ " .set mips3 \n"
+ " la %0,startpoint \n"
+ " la %1,endpoint \n"
+ " .set pop \n"
+ : "=r" (start), "=r" (end)
+ :
+ );
+
+ for (iptr = (void *)((unsigned int)start & ~(L1_CACHE_BYTES - 1));
+ iptr < end; iptr += L1_CACHE_BYTES)
+ cache_op(Fill, iptr);
+
+ __asm__ __volatile__ (
+ "startpoint: \n"
+ );
+
+ /* Put the DDRC into self-refresh mode */
+ DDRC_INDIRECT_WRITE(DDRC_CTL(10), 0xb, 1 << 16);
+
+ /*
+ * IMPORTANT!
+ * DO NOT do anything from here on out that might even
+ * think about fetching from RAM - i.e., don't call any
+ * non-inlined functions, and be VERY sure that any inline
+ * functions you do call do NOT access any sort of RAM
+ * anywhere!
+ */
+
+ /* Wait a bit for the DDRC to settle */
+ for (i = 0; i < 100000000; i++);
+
+#if defined(CONFIG_PMC_MSP7120_GW)
+ /*
+ * Set GPIO 9 HI, (tied to board reset logic)
+ * GPIO 9 is the 4th GPIO of register 3
+ *
+ * NOTE: We cannot use the higher-level msp_gpio_mode()/out()
+ * as GPIO char driver may not be enabled and it would look up
+ * data inRAM!
+ */
+ set_value_reg32(GPIO_CFG3_REG,
+ basic_mode_mask(MSP_BOARD_RESET_GPIO),
+ basic_mode(MSP_GPIO_OUTPUT, MSP_BOARD_RESET_GPIO));
+ set_reg32(GPIO_DATA3_REG,
+ basic_data_mask(MSP_BOARD_RESET_GPIO));
+
+ /*
+ * In case GPIO9 doesn't reset the board (jumper configurable!)
+ * fallback to device reset below.
+ */
+#endif
+ /* Set bit 1 of the MSP7120 reset register */
+ *RST_SET_REG = 0x00000001;
+
+ __asm__ __volatile__ (
+ "endpoint: \n"
+ );
+}
+#endif
+
+void msp_restart(char *command)
+{
+ printk(KERN_WARNING "Now rebooting .......\n");
+
+#if defined(CONFIG_PMC_MSP7120_EVAL) || \
+ defined(CONFIG_PMC_MSP7120_GW) || \
+ defined(CONFIG_PMC_MSP7120_FPGA)
+ msp7120_reset();
+#else
+ /* No chip-specific reset code, just jump to the ROM reset vector */
+ set_c0_status(ST0_BEV | ST0_ERL);
+ change_c0_config(CONF_CM_CMASK, CONF_CM_UNCACHED);
+ flush_cache_all();
+ write_c0_wired(0);
+
+ __asm__ __volatile__("jr\t%0"::"r"(0xbfc00000));
+#endif
+}
+
+void msp_halt(void)
+{
+ printk(KERN_WARNING "\n** You can safely turn off the power\n");
+ while (1)
+ /* If possible call official function to get CPU WARs */
+ if (cpu_wait)
+ (*cpu_wait)();
+ else
+ __asm__(".set\tmips3\n\t" "wait\n\t" ".set\tmips0");
+}
+
+void msp_power_off(void)
+{
+ msp_halt();
+}
+
+void __init plat_mem_setup(void)
+{
+ _machine_restart = msp_restart;
+ _machine_halt = msp_halt;
+ pm_power_off = msp_power_off;
+
+ board_time_init = msp_timer_init;
+}
+
+void __init prom_init(void)
+{
+ unsigned long family;
+ unsigned long revision;
+
+ prom_argc = fw_arg0;
+ prom_argv = (char **)fw_arg1;
+ prom_envp = (char **)fw_arg2;
+
+ /*
+ * Someday we can use this with PMON2000 to get a
+ * platform call prom routines for output etc. without
+ * having to use grody hacks. For now it's unused.
+ *
+ * struct callvectors *cv = (struct callvectors *) fw_arg3;
+ */
+ family = identify_family();
+ revision = identify_revision();
+
+ switch (family) {
+ case FAMILY_FPGA:
+ if (FPGA_IS_MSP4200(revision)) {
+ /* Old-style revision ID */
+ mips_machgroup = MACH_GROUP_MSP;
+ mips_machtype = MACH_MSP4200_FPGA;
+ } else {
+ mips_machgroup = MACH_GROUP_MSP;
+ mips_machtype = MACH_MSP_OTHER;
+ }
+ break;
+
+ case FAMILY_MSP4200:
+ mips_machgroup = MACH_GROUP_MSP;
+#if defined(CONFIG_PMC_MSP4200_EVAL)
+ mips_machtype = MACH_MSP4200_EVAL;
+#elif defined(CONFIG_PMC_MSP4200_GW)
+ mips_machtype = MACH_MSP4200_GW;
+#else
+ mips_machtype = MACH_MSP_OTHER;
+#endif
+ break;
+
+ case FAMILY_MSP4200_FPGA:
+ mips_machgroup = MACH_GROUP_MSP;
+ mips_machtype = MACH_MSP4200_FPGA;
+ break;
+
+ case FAMILY_MSP7100:
+ mips_machgroup = MACH_GROUP_MSP;
+#if defined(CONFIG_PMC_MSP7120_EVAL)
+ mips_machtype = MACH_MSP7120_EVAL;
+#elif defined(CONFIG_PMC_MSP7120_GW)
+ mips_machtype = MACH_MSP7120_GW;
+#else
+ mips_machtype = MACH_MSP_OTHER;
+#endif
+ break;
+
+ case FAMILY_MSP7100_FPGA:
+ mips_machgroup = MACH_GROUP_MSP;
+ mips_machtype = MACH_MSP7120_FPGA;
+ break;
+
+ default:
+ /* we don't recognize the machine */
+ mips_machgroup = MACH_GROUP_UNKNOWN;
+ mips_machtype = MACH_UNKNOWN;
+ break;
+ }
+
+ /* make sure we have the right initialization routine - sanity */
+ if (mips_machgroup != MACH_GROUP_MSP) {
+ ppfinit("Unknown machine group in a "
+ "MSP initialization routine\n");
+ panic("***Bogosity factor five***, exiting\n");
+ }
+
+ prom_init_cmdline();
+
+ prom_meminit();
+
+ /*
+ * Sub-system setup follows.
+ * Setup functions can either be called here or using the
+ * subsys_initcall mechanism (i.e. see msp_pci_setup). The
+ * order in which they are called can be changed by using the
+ * link order in arch/mips/pmc-sierra/msp71xx/Makefile.
+ *
+ * NOTE: Please keep sub-system specific initialization code
+ * in separate specific files.
+ */
+ msp_serial_setup();
+
+#ifdef CONFIG_PMCTWILED
+ /*
+ * Setup LED states before the subsys_initcall loads other
+ * dependant drivers/modules.
+ */
+ pmctwiled_setup();
+#endif
+}
--- /dev/null
+/*
+ * Setting up the clock on MSP SOCs. No RTC typically.
+ *
+ * Carsten Langgaard, carstenl@mips.com
+ * Copyright (C) 1999,2000 MIPS Technologies, Inc. All rights reserved.
+ *
+ * ########################################################################
+ *
+ * This program is free software; you can distribute it and/or modify it
+ * under the terms of the GNU General Public License (Version 2) as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ * for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+ *
+ * ########################################################################
+ */
+
+#include <linux/init.h>
+#include <linux/kernel_stat.h>
+#include <linux/sched.h>
+#include <linux/spinlock.h>
+#include <linux/module.h>
+#include <linux/ptrace.h>
+
+#include <asm/mipsregs.h>
+#include <asm/time.h>
+
+#include <msp_prom.h>
+#include <msp_int.h>
+#include <msp_regs.h>
+
+void __init msp_timer_init(void)
+{
+ char *endp, *s;
+ unsigned long cpu_rate = 0;
+
+ if (cpu_rate == 0) {
+ s = prom_getenv("clkfreqhz");
+ cpu_rate = simple_strtoul(s, &endp, 10);
+ if (endp != NULL && *endp != 0) {
+ printk(KERN_ERR
+ "Clock rate in Hz parse error: %s\n", s);
+ cpu_rate = 0;
+ }
+ }
+
+ if (cpu_rate == 0) {
+ s = prom_getenv("clkfreq");
+ cpu_rate = 1000 * simple_strtoul(s, &endp, 10);
+ if (endp != NULL && *endp != 0) {
+ printk(KERN_ERR
+ "Clock rate in MHz parse error: %s\n", s);
+ cpu_rate = 0;
+ }
+ }
+
+ if (cpu_rate == 0) {
+#if defined(CONFIG_PMC_MSP7120_EVAL) \
+ || defined(CONFIG_PMC_MSP7120_GW)
+ cpu_rate = 400000000;
+#elif defined(CONFIG_PMC_MSP7120_FPGA)
+ cpu_rate = 25000000;
+#else
+ cpu_rate = 150000000;
+#endif
+ printk(KERN_ERR
+ "Failed to determine CPU clock rate, "
+ "assuming %ld hz ...\n", cpu_rate);
+ }
+
+ printk(KERN_WARNING "Clock rate set to %ld\n", cpu_rate);
+
+ /* timer frequency is 1/2 clock rate */
+ mips_hpt_frequency = cpu_rate/2;
+}
+
+
+void __init plat_timer_setup(struct irqaction *irq)
+{
+#ifdef CONFIG_IRQ_MSP_CIC
+ /* we are using the vpe0 counter for timer interrupts */
+ setup_irq(MSP_INT_VPE0_TIMER, irq);
+#else
+ /* we are using the mips counter for timer interrupts */
+ setup_irq(MSP_INT_TIMER, irq);
+#endif
+}
--- /dev/null
+/*
+ * The setup file for USB related hardware on PMC-Sierra MSP processors.
+ *
+ * Copyright 2006-2007 PMC-Sierra, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
+ * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
+ * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
+ * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/dma-mapping.h>
+#include <linux/init.h>
+#include <linux/ioport.h>
+#include <linux/platform_device.h>
+
+#include <asm/mipsregs.h>
+
+#include <msp_regs.h>
+#include <msp_int.h>
+#include <msp_prom.h>
+
+#if defined(CONFIG_USB_EHCI_HCD)
+static struct resource msp_usbhost_resources [] = {
+ [0] = {
+ .start = MSP_USB_BASE_START,
+ .end = MSP_USB_BASE_END,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = MSP_INT_USB,
+ .end = MSP_INT_USB,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static u64 msp_usbhost_dma_mask = DMA_32BIT_MASK;
+
+static struct platform_device msp_usbhost_device = {
+ .name = "pmcmsp-ehci",
+ .id = 0,
+ .dev = {
+ .dma_mask = &msp_usbhost_dma_mask,
+ .coherent_dma_mask = DMA_32BIT_MASK,
+ },
+ .num_resources = ARRAY_SIZE (msp_usbhost_resources),
+ .resource = msp_usbhost_resources,
+};
+#endif /* CONFIG_USB_EHCI_HCD */
+
+#if defined(CONFIG_USB_GADGET)
+static struct resource msp_usbdev_resources [] = {
+ [0] = {
+ .start = MSP_USB_BASE,
+ .end = MSP_USB_BASE_END,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = MSP_INT_USB,
+ .end = MSP_INT_USB,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static u64 msp_usbdev_dma_mask = DMA_32BIT_MASK;
+
+static struct platform_device msp_usbdev_device = {
+ .name = "msp71xx_udc",
+ .id = 0,
+ .dev = {
+ .dma_mask = &msp_usbdev_dma_mask,
+ .coherent_dma_mask = DMA_32BIT_MASK,
+ },
+ .num_resources = ARRAY_SIZE (msp_usbdev_resources),
+ .resource = msp_usbdev_resources,
+};
+#endif /* CONFIG_USB_GADGET */
+
+#if defined(CONFIG_USB_EHCI_HCD) || defined(CONFIG_USB_GADGET)
+static struct platform_device *msp_devs[1];
+#endif
+
+
+static int __init msp_usb_setup(void)
+{
+#if defined(CONFIG_USB_EHCI_HCD) || defined(CONFIG_USB_GADGET)
+ char *strp;
+ char envstr[32];
+ unsigned int val = 0;
+ int result = 0;
+
+ /*
+ * construct environment name usbmode
+ * set usbmode <host/device> as pmon environment var
+ */
+ snprintf((char *)&envstr[0], sizeof(envstr), "usbmode");
+
+#if defined(CONFIG_USB_EHCI_HCD)
+ /* default to host mode */
+ val = 1;
+#endif
+
+ /* get environment string */
+ strp = prom_getenv((char *)&envstr[0]);
+ if (strp) {
+ if (!strcmp(strp, "device"))
+ val = 0;
+ }
+
+ if (val) {
+#if defined(CONFIG_USB_EHCI_HCD)
+ /* get host mode device */
+ msp_devs[0] = &msp_usbhost_device;
+ ppfinit("platform add USB HOST done %s.\n",
+ msp_devs[0]->name);
+
+ result = platform_add_devices(msp_devs, ARRAY_SIZE (msp_devs));
+#endif /* CONFIG_USB_EHCI_HCD */
+ }
+#if defined(CONFIG_USB_GADGET)
+ else {
+ /* get device mode structure */
+ msp_devs[0] = &msp_usbdev_device;
+ ppfinit("platform add USB DEVICE done %s.\n",
+ msp_devs[0]->name);
+
+ result = platform_add_devices(msp_devs, ARRAY_SIZE (msp_devs));
+ }
+#endif /* CONFIG_USB_GADGET */
+#endif /* CONFIG_USB_EHCI_HCD || CONFIG_USB_GADGET */
+
+ return result;
+}
+
+subsys_initcall(msp_usb_setup);
--- /dev/null
+/*
+ * Defines for the MSP interrupt controller.
+ *
+ * Copyright (C) 1999 MIPS Technologies, Inc. All rights reserved.
+ * Author: Carsten Langgaard, carstenl@mips.com
+ *
+ * ########################################################################
+ *
+ * This program is free software; you can distribute it and/or modify it
+ * under the terms of the GNU General Public License (Version 2) as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ * for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+ *
+ * ########################################################################
+ */
+
+#ifndef _MSP_CIC_INT_H
+#define _MSP_CIC_INT_H
+
+/*
+ * The PMC-Sierra CIC interrupts are all centrally managed by the
+ * CIC sub-system.
+ * We attempt to keep the interrupt numbers as consistent as possible
+ * across all of the MSP devices, but some differences will creep in ...
+ * The interrupts which are directly forwarded to the MIPS core interrupts
+ * are assigned interrupts in the range 0-7, interrupts cascaded through
+ * the CIC are assigned interrupts 8-39. The cascade occurs on C_IRQ4
+ * (MSP_INT_CIC). Currently we don't really distinguish between VPE1
+ * and VPE0 (or thread contexts for that matter). Will have to fix.
+ * The PER interrupts are assigned interrupts in the range 40-71.
+*/
+
+
+/*
+ * IRQs directly forwarded to the CPU
+ */
+#define MSP_MIPS_INTBASE 0
+#define MSP_INT_SW0 0 /* IRQ for swint0, C_SW0 */
+#define MSP_INT_SW1 1 /* IRQ for swint1, C_SW1 */
+#define MSP_INT_MAC0 2 /* IRQ for MAC 0, C_IRQ0 */
+#define MSP_INT_MAC1 3 /* IRQ for MAC 1, C_IRQ1 */
+#define MSP_INT_USB 4 /* IRQ for USB, C_IRQ2 */
+#define MSP_INT_SAR 5 /* IRQ for ADSL2+ SAR, C_IRQ3 */
+#define MSP_INT_CIC 6 /* IRQ for CIC block, C_IRQ4 */
+#define MSP_INT_SEC 7 /* IRQ for Sec engine, C_IRQ5 */
+
+/*
+ * IRQs cascaded on CPU interrupt 4 (CAUSE bit 12, C_IRQ4)
+ * These defines should be tied to the register definitions for the CIC
+ * interrupt routine. For now, just use hard-coded values.
+ */
+#define MSP_CIC_INTBASE (MSP_MIPS_INTBASE + 8)
+#define MSP_INT_EXT0 (MSP_CIC_INTBASE + 0)
+ /* External interrupt 0 */
+#define MSP_INT_EXT1 (MSP_CIC_INTBASE + 1)
+ /* External interrupt 1 */
+#define MSP_INT_EXT2 (MSP_CIC_INTBASE + 2)
+ /* External interrupt 2 */
+#define MSP_INT_EXT3 (MSP_CIC_INTBASE + 3)
+ /* External interrupt 3 */
+#define MSP_INT_CPUIF (MSP_CIC_INTBASE + 4)
+ /* CPU interface interrupt */
+#define MSP_INT_EXT4 (MSP_CIC_INTBASE + 5)
+ /* External interrupt 4 */
+#define MSP_INT_CIC_USB (MSP_CIC_INTBASE + 6)
+ /* Cascaded IRQ for USB */
+#define MSP_INT_MBOX (MSP_CIC_INTBASE + 7)
+ /* Sec engine mailbox IRQ */
+#define MSP_INT_EXT5 (MSP_CIC_INTBASE + 8)
+ /* External interrupt 5 */
+#define MSP_INT_TDM (MSP_CIC_INTBASE + 9)
+ /* TDM interrupt */
+#define MSP_INT_CIC_MAC0 (MSP_CIC_INTBASE + 10)
+ /* Cascaded IRQ for MAC 0 */
+#define MSP_INT_CIC_MAC1 (MSP_CIC_INTBASE + 11)
+ /* Cascaded IRQ for MAC 1 */
+#define MSP_INT_CIC_SEC (MSP_CIC_INTBASE + 12)
+ /* Cascaded IRQ for sec engine */
+#define MSP_INT_PER (MSP_CIC_INTBASE + 13)
+ /* Peripheral interrupt */
+#define MSP_INT_TIMER0 (MSP_CIC_INTBASE + 14)
+ /* SLP timer 0 */
+#define MSP_INT_TIMER1 (MSP_CIC_INTBASE + 15)
+ /* SLP timer 1 */
+#define MSP_INT_TIMER2 (MSP_CIC_INTBASE + 16)
+ /* SLP timer 2 */
+#define MSP_INT_VPE0_TIMER (MSP_CIC_INTBASE + 17)
+ /* VPE0 MIPS timer */
+#define MSP_INT_BLKCP (MSP_CIC_INTBASE + 18)
+ /* Block Copy */
+#define MSP_INT_UART0 (MSP_CIC_INTBASE + 19)
+ /* UART 0 */
+#define MSP_INT_PCI (MSP_CIC_INTBASE + 20)
+ /* PCI subsystem */
+#define MSP_INT_EXT6 (MSP_CIC_INTBASE + 21)
+ /* External interrupt 5 */
+#define MSP_INT_PCI_MSI (MSP_CIC_INTBASE + 22)
+ /* PCI Message Signal */
+#define MSP_INT_CIC_SAR (MSP_CIC_INTBASE + 23)
+ /* Cascaded ADSL2+ SAR IRQ */
+#define MSP_INT_DSL (MSP_CIC_INTBASE + 24)
+ /* ADSL2+ IRQ */
+#define MSP_INT_CIC_ERR (MSP_CIC_INTBASE + 25)
+ /* SLP error condition */
+#define MSP_INT_VPE1_TIMER (MSP_CIC_INTBASE + 26)
+ /* VPE1 MIPS timer */
+#define MSP_INT_VPE0_PC (MSP_CIC_INTBASE + 27)
+ /* VPE0 Performance counter */
+#define MSP_INT_VPE1_PC (MSP_CIC_INTBASE + 28)
+ /* VPE1 Performance counter */
+#define MSP_INT_EXT7 (MSP_CIC_INTBASE + 29)
+ /* External interrupt 5 */
+#define MSP_INT_VPE0_SW (MSP_CIC_INTBASE + 30)
+ /* VPE0 Software interrupt */
+#define MSP_INT_VPE1_SW (MSP_CIC_INTBASE + 31)
+ /* VPE0 Software interrupt */
+
+/*
+ * IRQs cascaded on CIC PER interrupt (MSP_INT_PER)
+ */
+#define MSP_PER_INTBASE (MSP_CIC_INTBASE + 32)
+/* Reserved 0-1 */
+#define MSP_INT_UART1 (MSP_PER_INTBASE + 2)
+ /* UART 1 */
+/* Reserved 3-5 */
+#define MSP_INT_2WIRE (MSP_PER_INTBASE + 6)
+ /* 2-wire */
+#define MSP_INT_TM0 (MSP_PER_INTBASE + 7)
+ /* Peripheral timer block out 0 */
+#define MSP_INT_TM1 (MSP_PER_INTBASE + 8)
+ /* Peripheral timer block out 1 */
+/* Reserved 9 */
+#define MSP_INT_SPRX (MSP_PER_INTBASE + 10)
+ /* SPI RX complete */
+#define MSP_INT_SPTX (MSP_PER_INTBASE + 11)
+ /* SPI TX complete */
+#define MSP_INT_GPIO (MSP_PER_INTBASE + 12)
+ /* GPIO */
+#define MSP_INT_PER_ERR (MSP_PER_INTBASE + 13)
+ /* Peripheral error */
+/* Reserved 14-31 */
+
+#endif /* !_MSP_CIC_INT_H */
--- /dev/null
+/*
+ * Defines for the MSP interrupt handlers.
+ *
+ * Copyright (C) 2005, PMC-Sierra, Inc. All rights reserved.
+ * Author: Andrew Hughes, Andrew_Hughes@pmc-sierra.com
+ *
+ * ########################################################################
+ *
+ * This program is free software; you can distribute it and/or modify it
+ * under the terms of the GNU General Public License (Version 2) as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ * for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+ *
+ * ########################################################################
+ */
+
+#ifndef _MSP_INT_H
+#define _MSP_INT_H
+
+/*
+ * The PMC-Sierra MSP product line has at least two different interrupt
+ * controllers, the SLP register based scheme and the CIC interrupt
+ * controller block mechanism. This file distinguishes between them
+ * so that devices see a uniform interface.
+ */
+
+#if defined(CONFIG_IRQ_MSP_SLP)
+ #include "msp_slp_int.h"
+#elif defined(CONFIG_IRQ_MSP_CIC)
+ #include "msp_cic_int.h"
+#else
+ #error "What sort of interrupt controller does *your* MSP have?"
+#endif
+
+#endif /* !_MSP_INT_H */
--- /dev/null
+/*
+ * MIPS boards bootprom interface for the Linux kernel.
+ *
+ * Copyright (C) 2000 MIPS Technologies, Inc. All rights reserved.
+ * Author: Carsten Langgaard, carstenl@mips.com
+ *
+ * ########################################################################
+ *
+ * This program is free software; you can distribute it and/or modify it
+ * under the terms of the GNU General Public License (Version 2) as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ * for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+ *
+ * ########################################################################
+ */
+
+#ifndef _ASM_MSP_PROM_H
+#define _ASM_MSP_PROM_H
+
+#include <linux/types.h>
+
+#define DEVICEID "deviceid"
+#define FEATURES "features"
+#define PROM_ENV "prom_env"
+#define PROM_ENV_FILE "/proc/"PROM_ENV
+#define PROM_ENV_SIZE 256
+
+#define CPU_DEVID_FAMILY 0x0000ff00
+#define CPU_DEVID_REVISION 0x000000ff
+
+#define FPGA_IS_POLO(revision) \
+ (((revision >= 0xb0) && (revision < 0xd0)))
+#define FPGA_IS_5000(revision) \
+ ((revision >= 0x80) && (revision <= 0x90))
+#define FPGA_IS_ZEUS(revision) ((revision < 0x7f))
+#define FPGA_IS_DUET(revision) \
+ (((revision >= 0xa0) && (revision < 0xb0)))
+#define FPGA_IS_MSP4200(revision) ((revision >= 0xd0))
+#define FPGA_IS_MSP7100(revision) ((revision >= 0xd0))
+
+#define MACHINE_TYPE_POLO "POLO"
+#define MACHINE_TYPE_DUET "DUET"
+#define MACHINE_TYPE_ZEUS "ZEUS"
+#define MACHINE_TYPE_MSP2000REVB "MSP2000REVB"
+#define MACHINE_TYPE_MSP5000 "MSP5000"
+#define MACHINE_TYPE_MSP4200 "MSP4200"
+#define MACHINE_TYPE_MSP7120 "MSP7120"
+#define MACHINE_TYPE_MSP7130 "MSP7130"
+#define MACHINE_TYPE_OTHER "OTHER"
+
+#define MACHINE_TYPE_POLO_FPGA "POLO-FPGA"
+#define MACHINE_TYPE_DUET_FPGA "DUET-FPGA"
+#define MACHINE_TYPE_ZEUS_FPGA "ZEUS_FPGA"
+#define MACHINE_TYPE_MSP2000REVB_FPGA "MSP2000REVB-FPGA"
+#define MACHINE_TYPE_MSP5000_FPGA "MSP5000-FPGA"
+#define MACHINE_TYPE_MSP4200_FPGA "MSP4200-FPGA"
+#define MACHINE_TYPE_MSP7100_FPGA "MSP7100-FPGA"
+#define MACHINE_TYPE_OTHER_FPGA "OTHER-FPGA"
+
+/* Device Family definitions */
+#define FAMILY_FPGA 0x0000
+#define FAMILY_ZEUS 0x1000
+#define FAMILY_POLO 0x2000
+#define FAMILY_DUET 0x4000
+#define FAMILY_TRIAD 0x5000
+#define FAMILY_MSP4200 0x4200
+#define FAMILY_MSP4200_FPGA 0x4f00
+#define FAMILY_MSP7100 0x7100
+#define FAMILY_MSP7100_FPGA 0x7f00
+
+/* Device Type definitions */
+#define TYPE_MSP7120 0x7120
+#define TYPE_MSP7130 0x7130
+
+#define ENET_KEY 'E'
+#define ENETTXD_KEY 'e'
+#define PCI_KEY 'P'
+#define PCIMUX_KEY 'p'
+#define SEC_KEY 'S'
+#define SPAD_KEY 'D'
+#define TDM_KEY 'T'
+#define ZSP_KEY 'Z'
+
+#define FEATURE_NOEXIST '-'
+#define FEATURE_EXIST '+'
+
+#define ENET_MII 'M'
+#define ENET_RMII 'R'
+
+#define ENETTXD_FALLING 'F'
+#define ENETTXD_RISING 'R'
+
+#define PCI_HOST 'H'
+#define PCI_PERIPHERAL 'P'
+
+#define PCIMUX_FULL 'F'
+#define PCIMUX_SINGLE 'S'
+
+#define SEC_DUET 'D'
+#define SEC_POLO 'P'
+#define SEC_SLOW 'S'
+#define SEC_TRIAD 'T'
+
+#define SPAD_POLO 'P'
+
+#define TDM_DUET 'D' /* DUET TDMs might exist */
+#define TDM_POLO 'P' /* POLO TDMs might exist */
+#define TDM_TRIAD 'T' /* TRIAD TDMs might exist */
+
+#define ZSP_DUET 'D' /* one DUET zsp engine */
+#define ZSP_TRIAD 'T' /* two TRIAD zsp engines */
+
+extern char *prom_getcmdline(void);
+extern char *prom_getenv(char *name);
+extern void prom_init_cmdline(void);
+extern void prom_meminit(void);
+extern void prom_fixup_mem_map(unsigned long start_mem,
+ unsigned long end_mem);
+
+#ifdef CONFIG_MTD_PMC_MSP_RAMROOT
+extern bool get_ramroot(void **start, unsigned long *size);
+#endif
+
+extern int get_ethernet_addr(char *ethaddr_name, char *ethernet_addr);
+extern unsigned long get_deviceid(void);
+extern char identify_enet(unsigned long interface_num);
+extern char identify_enetTxD(unsigned long interface_num);
+extern char identify_pci(void);
+extern char identify_sec(void);
+extern char identify_spad(void);
+extern char identify_sec(void);
+extern char identify_tdm(void);
+extern char identify_zsp(void);
+extern unsigned long identify_family(void);
+extern unsigned long identify_revision(void);
+
+/*
+ * The following macro calls prom_printf and puts the format string
+ * into an init section so it can be reclaimed.
+ */
+#define ppfinit(f, x...) \
+ do { \
+ static char _f[] __initdata = KERN_INFO f; \
+ printk(_f, ## x); \
+ } while (0)
+
+/* Memory descriptor management. */
+#define PROM_MAX_PMEMBLOCKS 7 /* 6 used */
+
+enum yamon_memtypes {
+ yamon_dontuse,
+ yamon_prom,
+ yamon_free,
+};
+
+struct prom_pmemblock {
+ unsigned long base; /* Within KSEG0. */
+ unsigned int size; /* In bytes. */
+ unsigned int type; /* free or prom memory */
+};
+
+extern int prom_argc;
+extern char **prom_argv;
+extern char **prom_envp;
+extern int *prom_vec;
+extern struct prom_pmemblock *prom_getmdesc(void);
+
+#endif /* !_ASM_MSP_PROM_H */
--- /dev/null
+/*
+ * SMP/VPE-safe functions to access "registers" (see note).
+ *
+ * NOTES:
+* - These macros use ll/sc instructions, so it is your responsibility to
+ * ensure these are available on your platform before including this file.
+ * - The MIPS32 spec states that ll/sc results are undefined for uncached
+ * accesses. This means they can't be used on HW registers accessed
+ * through kseg1. Code which requires these macros for this purpose must
+ * front-end the registers with cached memory "registers" and have a single
+ * thread update the actual HW registers.
+ * - A maximum of 2k of code can be inserted between ll and sc. Every
+ * memory accesses between the instructions will increase the chance of
+ * sc failing and having to loop.
+ * - When using custom_read_reg32/custom_write_reg32 only perform the
+ * necessary logical operations on the register value in between these
+ * two calls. All other logic should be performed before the first call.
+ * - There is a bug on the R10000 chips which has a workaround. If you
+ * are affected by this bug, make sure to define the symbol 'R10000_LLSC_WAR'
+ * to be non-zero. If you are using this header from within linux, you may
+ * include <asm/war.h> before including this file to have this defined
+ * appropriately for you.
+ *
+ * Copyright 2005-2007 PMC-Sierra, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
+ * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO
+ * EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc., 675
+ * Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#ifndef __ASM_REGOPS_H__
+#define __ASM_REGOPS_H__
+
+#include <linux/types.h>
+
+#include <asm/war.h>
+
+#ifndef R10000_LLSC_WAR
+#define R10000_LLSC_WAR 0
+#endif
+
+#if R10000_LLSC_WAR == 1
+#define __beqz "beqzl "
+#else
+#define __beqz "beqz "
+#endif
+
+#ifndef _LINUX_TYPES_H
+typedef unsigned int u32;
+#endif
+
+/*
+ * Sets all the masked bits to the corresponding value bits
+ */
+static inline void set_value_reg32(volatile u32 *const addr,
+ u32 const mask,
+ u32 const value)
+{
+ u32 temp;
+
+ __asm__ __volatile__(
+ " .set push \n"
+ " .set mips3 \n"
+ "1: ll %0, %1 # set_value_reg32 \n"
+ " and %0, %2 \n"
+ " or %0, %3 \n"
+ " sc %0, %1 \n"
+ " "__beqz"%0, 1b \n"
+ " nop \n"
+ " .set pop \n"
+ : "=&r" (temp), "=m" (*addr)
+ : "ir" (~mask), "ir" (value), "m" (*addr));
+}
+
+/*
+ * Sets all the masked bits to '1'
+ */
+static inline void set_reg32(volatile u32 *const addr,
+ u32 const mask)
+{
+ u32 temp;
+
+ __asm__ __volatile__(
+ " .set push \n"
+ " .set mips3 \n"
+ "1: ll %0, %1 # set_reg32 \n"
+ " or %0, %2 \n"
+ " sc %0, %1 \n"
+ " "__beqz"%0, 1b \n"
+ " nop \n"
+ " .set pop \n"
+ : "=&r" (temp), "=m" (*addr)
+ : "ir" (mask), "m" (*addr));
+}
+
+/*
+ * Sets all the masked bits to '0'
+ */
+static inline void clear_reg32(volatile u32 *const addr,
+ u32 const mask)
+{
+ u32 temp;
+
+ __asm__ __volatile__(
+ " .set push \n"
+ " .set mips3 \n"
+ "1: ll %0, %1 # clear_reg32 \n"
+ " and %0, %2 \n"
+ " sc %0, %1 \n"
+ " "__beqz"%0, 1b \n"
+ " nop \n"
+ " .set pop \n"
+ : "=&r" (temp), "=m" (*addr)
+ : "ir" (~mask), "m" (*addr));
+}
+
+/*
+ * Toggles all masked bits from '0' to '1' and '1' to '0'
+ */
+static inline void toggle_reg32(volatile u32 *const addr,
+ u32 const mask)
+{
+ u32 temp;
+
+ __asm__ __volatile__(
+ " .set push \n"
+ " .set mips3 \n"
+ "1: ll %0, %1 # toggle_reg32 \n"
+ " xor %0, %2 \n"
+ " sc %0, %1 \n"
+ " "__beqz"%0, 1b \n"
+ " nop \n"
+ " .set pop \n"
+ : "=&r" (temp), "=m" (*addr)
+ : "ir" (mask), "m" (*addr));
+}
+
+/*
+ * Read all masked bits others are returned as '0'
+ */
+static inline u32 read_reg32(volatile u32 *const addr,
+ u32 const mask)
+{
+ u32 temp;
+
+ __asm__ __volatile__(
+ " .set push \n"
+ " .set noreorder \n"
+ " lw %0, %1 # read \n"
+ " and %0, %2 # mask \n"
+ " .set pop \n"
+ : "=&r" (temp)
+ : "m" (*addr), "ir" (mask));
+
+ return temp;
+}
+
+/*
+ * blocking_read_reg32 - Read address with blocking load
+ *
+ * Uncached writes need to be read back to ensure they reach RAM.
+ * The returned value must be 'used' to prevent from becoming a
+ * non-blocking load.
+ */
+static inline u32 blocking_read_reg32(volatile u32 *const addr)
+{
+ u32 temp;
+
+ __asm__ __volatile__(
+ " .set push \n"
+ " .set noreorder \n"
+ " lw %0, %1 # read \n"
+ " move %0, %0 # block \n"
+ " .set pop \n"
+ : "=&r" (temp)
+ : "m" (*addr));
+
+ return temp;
+}
+
+/*
+ * For special strange cases only:
+ *
+ * If you need custom processing within a ll/sc loop, use the following macros
+ * VERY CAREFULLY:
+ *
+ * u32 tmp; <-- Define a variable to hold the data
+ *
+ * custom_read_reg32(address, tmp); <-- Reads the address and put the value
+ * in the 'tmp' variable given
+ *
+ * From here on out, you are (basicly) atomic, so don't do anything too
+ * fancy!
+ * Also, this code may loop if the end of this block fails to write
+ * everything back safely due do the other CPU, so do NOT do anything
+ * with side-effects!
+ *
+ * custom_write_reg32(address, tmp); <-- Writes back 'tmp' safely.
+ */
+#define custom_read_reg32(address, tmp) \
+ __asm__ __volatile__( \
+ " .set push \n" \
+ " .set mips3 \n" \
+ "1: ll %0, %1 #custom_read_reg32 \n" \
+ " .set pop \n" \
+ : "=r" (tmp), "=m" (*address) \
+ : "m" (*address))
+
+#define custom_write_reg32(address, tmp) \
+ __asm__ __volatile__( \
+ " .set push \n" \
+ " .set mips3 \n" \
+ " sc %0, %1 #custom_write_reg32 \n" \
+ " "__beqz"%0, 1b \n" \
+ " nop \n" \
+ " .set pop \n" \
+ : "=&r" (tmp), "=m" (*address) \
+ : "0" (tmp), "m" (*address))
+
+#endif /* __ASM_REGOPS_H__ */
--- /dev/null
+/*
+ * Defines for the address space, registers and register configuration
+ * (bit masks, access macros etc) for the PMC-Sierra line of MSP products.
+ * This file contains addess maps for all the devices in the line of
+ * products but only has register definitions and configuration masks for
+ * registers which aren't definitely associated with any device. Things
+ * like clock settings, reset access, the ELB etc. Individual device
+ * drivers will reference the appropriate XXX_BASE value defined here
+ * and have individual registers offset from that.
+ *
+ * Copyright (C) 2005-2007 PMC-Sierra, Inc. All rights reserved.
+ * Author: Andrew Hughes, Andrew_Hughes@pmc-sierra.com
+ *
+ * ########################################################################
+ *
+ * This program is free software; you can distribute it and/or modify it
+ * under the terms of the GNU General Public License (Version 2) as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ * for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+ *
+ * ########################################################################
+ */
+
+#include <asm/addrspace.h>
+#include <linux/types.h>
+
+#ifndef _ASM_MSP_REGS_H
+#define _ASM_MSP_REGS_H
+
+/*
+ ########################################################################
+ # Address space and device base definitions #
+ ########################################################################
+ */
+
+/*
+ ***************************************************************************
+ * System Logic and Peripherals (ELB, UART0, etc) device address space *
+ ***************************************************************************
+ */
+#define MSP_SLP_BASE 0x1c000000
+ /* System Logic and Peripherals */
+#define MSP_RST_BASE (MSP_SLP_BASE + 0x10)
+ /* System reset register base */
+#define MSP_RST_SIZE 0x0C /* System reset register space */
+
+#define MSP_WTIMER_BASE (MSP_SLP_BASE + 0x04C)
+ /* watchdog timer base */
+#define MSP_ITIMER_BASE (MSP_SLP_BASE + 0x054)
+ /* internal timer base */
+#define MSP_UART0_BASE (MSP_SLP_BASE + 0x100)
+ /* UART0 controller base */
+#define MSP_BCPY_CTRL_BASE (MSP_SLP_BASE + 0x120)
+ /* Block Copy controller base */
+#define MSP_BCPY_DESC_BASE (MSP_SLP_BASE + 0x160)
+ /* Block Copy descriptor base */
+
+/*
+ ***************************************************************************
+ * PCI address space *
+ ***************************************************************************
+ */
+#define MSP_PCI_BASE 0x19000000
+
+/*
+ ***************************************************************************
+ * MSbus device address space *
+ ***************************************************************************
+ */
+#define MSP_MSB_BASE 0x18000000
+ /* MSbus address start */
+#define MSP_PER_BASE (MSP_MSB_BASE + 0x400000)
+ /* Peripheral device registers */
+#define MSP_MAC0_BASE (MSP_MSB_BASE + 0x600000)
+ /* MAC A device registers */
+#define MSP_MAC1_BASE (MSP_MSB_BASE + 0x700000)
+ /* MAC B device registers */
+#define MSP_MAC_SIZE 0xE0 /* MAC register space */
+
+#define MSP_SEC_BASE (MSP_MSB_BASE + 0x800000)
+ /* Security Engine registers */
+#define MSP_MAC2_BASE (MSP_MSB_BASE + 0x900000)
+ /* MAC C device registers */
+#define MSP_ADSL2_BASE (MSP_MSB_BASE + 0xA80000)
+ /* ADSL2 device registers */
+#define MSP_USB_BASE (MSP_MSB_BASE + 0xB40000)
+ /* USB device registers */
+#define MSP_USB_BASE_START (MSP_MSB_BASE + 0xB40100)
+ /* USB device registers */
+#define MSP_USB_BASE_END (MSP_MSB_BASE + 0xB401FF)
+ /* USB device registers */
+#define MSP_CPUIF_BASE (MSP_MSB_BASE + 0xC00000)
+ /* CPU interface registers */
+
+/* Devices within the MSbus peripheral block */
+#define MSP_UART1_BASE (MSP_PER_BASE + 0x030)
+ /* UART1 controller base */
+#define MSP_SPI_BASE (MSP_PER_BASE + 0x058)
+ /* SPI/MPI control registers */
+#define MSP_TWI_BASE (MSP_PER_BASE + 0x090)
+ /* Two-wire control registers */
+#define MSP_PTIMER_BASE (MSP_PER_BASE + 0x0F0)
+ /* Programmable timer control */
+
+/*
+ ***************************************************************************
+ * Physical Memory configuration address space *
+ ***************************************************************************
+ */
+#define MSP_MEM_CFG_BASE 0x17f00000
+
+#define MSP_MEM_INDIRECT_CTL_10 0x10
+
+/*
+ * Notes:
+ * 1) The SPI registers are split into two blocks, one offset from the
+ * MSP_SPI_BASE by 0x00 and the other offset from the MSP_SPI_BASE by
+ * 0x68. The SPI driver definitions for the register must be aware
+ * of this.
+ * 2) The block copy engine register are divided into two regions, one
+ * for the control/configuration of the engine proper and one for the
+ * values of the descriptors used in the copy process. These have
+ * different base defines (CTRL_BASE vs DESC_BASE)
+ * 3) These constants are for physical addresses which means that they
+ * work correctly with "ioremap" and friends. This means that device
+ * drivers will need to remap these addresses using ioremap and perhaps
+ * the readw/writew macros. Or they could use the regptr() macro
+ * defined below, but the readw/writew calls are the correct thing.
+ * 4) The UARTs have an additional status register offset from the base
+ * address. This register isn't used in the standard 8250 driver but
+ * may be used in other software. Consult the hardware datasheet for
+ * offset details.
+ * 5) For some unknown reason the security engine (MSP_SEC_BASE) registers
+ * start at an offset of 0x84 from the base address but the block of
+ * registers before this is reserved for the security engine. The
+ * driver will have to be aware of this but it makes the register
+ * definitions line up better with the documentation.
+ */
+
+/*
+ ########################################################################
+ # System register definitions. Not associated with a specific device #
+ ########################################################################
+ */
+
+/*
+ * This macro maps the physical register number into uncached space
+ * and (for C code) casts it into a u32 pointer so it can be dereferenced
+ * Normally these would be accessed with ioremap and readX/writeX, but
+ * these are convenient for a lot of internal kernel code.
+ */
+#ifdef __ASSEMBLER__
+ #define regptr(addr) (KSEG1ADDR(addr))
+#else
+ #define regptr(addr) ((volatile u32 *const)(KSEG1ADDR(addr)))
+#endif
+
+/*
+ ***************************************************************************
+ * System Logic and Peripherals (RESET, ELB, etc) registers *
+ ***************************************************************************
+ */
+
+/* System Control register definitions */
+#define DEV_ID_REG regptr(MSP_SLP_BASE + 0x00)
+ /* Device-ID RO */
+#define FWR_ID_REG regptr(MSP_SLP_BASE + 0x04)
+ /* Firmware-ID Register RW */
+#define SYS_ID_REG0 regptr(MSP_SLP_BASE + 0x08)
+ /* System-ID Register-0 RW */
+#define SYS_ID_REG1 regptr(MSP_SLP_BASE + 0x0C)
+ /* System-ID Register-1 RW */
+
+/* System Reset register definitions */
+#define RST_STS_REG regptr(MSP_SLP_BASE + 0x10)
+ /* System Reset Status RO */
+#define RST_SET_REG regptr(MSP_SLP_BASE + 0x14)
+ /* System Set Reset WO */
+#define RST_CLR_REG regptr(MSP_SLP_BASE + 0x18)
+ /* System Clear Reset WO */
+
+/* System Clock Registers */
+#define PCI_SLP_REG regptr(MSP_SLP_BASE + 0x1C)
+ /* PCI clock generator RW */
+#define URT_SLP_REG regptr(MSP_SLP_BASE + 0x20)
+ /* UART clock generator RW */
+/* reserved (MSP_SLP_BASE + 0x24) */
+/* reserved (MSP_SLP_BASE + 0x28) */
+#define PLL1_SLP_REG regptr(MSP_SLP_BASE + 0x2C)
+ /* PLL1 clock generator RW */
+#define PLL0_SLP_REG regptr(MSP_SLP_BASE + 0x30)
+ /* PLL0 clock generator RW */
+#define MIPS_SLP_REG regptr(MSP_SLP_BASE + 0x34)
+ /* MIPS clock generator RW */
+#define VE_SLP_REG regptr(MSP_SLP_BASE + 0x38)
+ /* Voice Eng clock generator RW */
+/* reserved (MSP_SLP_BASE + 0x3C) */
+#define MSB_SLP_REG regptr(MSP_SLP_BASE + 0x40)
+ /* MS-Bus clock generator RW */
+#define SMAC_SLP_REG regptr(MSP_SLP_BASE + 0x44)
+ /* Sec & MAC clock generator RW */
+#define PERF_SLP_REG regptr(MSP_SLP_BASE + 0x48)
+ /* Per & TDM clock generator RW */
+
+/* Interrupt Controller Registers */
+#define SLP_INT_STS_REG regptr(MSP_SLP_BASE + 0x70)
+ /* Interrupt status register RW */
+#define SLP_INT_MSK_REG regptr(MSP_SLP_BASE + 0x74)
+ /* Interrupt enable/mask RW */
+#define SE_MBOX_REG regptr(MSP_SLP_BASE + 0x78)
+ /* Security Engine mailbox RW */
+#define VE_MBOX_REG regptr(MSP_SLP_BASE + 0x7C)
+ /* Voice Engine mailbox RW */
+
+/* ELB Controller Registers */
+#define CS0_CNFG_REG regptr(MSP_SLP_BASE + 0x80)
+ /* ELB CS0 Configuration Reg */
+#define CS0_ADDR_REG regptr(MSP_SLP_BASE + 0x84)
+ /* ELB CS0 Base Address Reg */
+#define CS0_MASK_REG regptr(MSP_SLP_BASE + 0x88)
+ /* ELB CS0 Mask Register */
+#define CS0_ACCESS_REG regptr(MSP_SLP_BASE + 0x8C)
+ /* ELB CS0 access register */
+
+#define CS1_CNFG_REG regptr(MSP_SLP_BASE + 0x90)
+ /* ELB CS1 Configuration Reg */
+#define CS1_ADDR_REG regptr(MSP_SLP_BASE + 0x94)
+ /* ELB CS1 Base Address Reg */
+#define CS1_MASK_REG regptr(MSP_SLP_BASE + 0x98)
+ /* ELB CS1 Mask Register */
+#define CS1_ACCESS_REG regptr(MSP_SLP_BASE + 0x9C)
+ /* ELB CS1 access register */
+
+#define CS2_CNFG_REG regptr(MSP_SLP_BASE + 0xA0)
+ /* ELB CS2 Configuration Reg */
+#define CS2_ADDR_REG regptr(MSP_SLP_BASE + 0xA4)
+ /* ELB CS2 Base Address Reg */
+#define CS2_MASK_REG regptr(MSP_SLP_BASE + 0xA8)
+ /* ELB CS2 Mask Register */
+#define CS2_ACCESS_REG regptr(MSP_SLP_BASE + 0xAC)
+ /* ELB CS2 access register */
+
+#define CS3_CNFG_REG regptr(MSP_SLP_BASE + 0xB0)
+ /* ELB CS3 Configuration Reg */
+#define CS3_ADDR_REG regptr(MSP_SLP_BASE + 0xB4)
+ /* ELB CS3 Base Address Reg */
+#define CS3_MASK_REG regptr(MSP_SLP_BASE + 0xB8)
+ /* ELB CS3 Mask Register */
+#define CS3_ACCESS_REG regptr(MSP_SLP_BASE + 0xBC)
+ /* ELB CS3 access register */
+
+#define CS4_CNFG_REG regptr(MSP_SLP_BASE + 0xC0)
+ /* ELB CS4 Configuration Reg */
+#define CS4_ADDR_REG regptr(MSP_SLP_BASE + 0xC4)
+ /* ELB CS4 Base Address Reg */
+#define CS4_MASK_REG regptr(MSP_SLP_BASE + 0xC8)
+ /* ELB CS4 Mask Register */
+#define CS4_ACCESS_REG regptr(MSP_SLP_BASE + 0xCC)
+ /* ELB CS4 access register */
+
+#define CS5_CNFG_REG regptr(MSP_SLP_BASE + 0xD0)
+ /* ELB CS5 Configuration Reg */
+#define CS5_ADDR_REG regptr(MSP_SLP_BASE + 0xD4)
+ /* ELB CS5 Base Address Reg */
+#define CS5_MASK_REG regptr(MSP_SLP_BASE + 0xD8)
+ /* ELB CS5 Mask Register */
+#define CS5_ACCESS_REG regptr(MSP_SLP_BASE + 0xDC)
+ /* ELB CS5 access register */
+
+/* reserved 0xE0 - 0xE8 */
+#define ELB_1PC_EN_REG regptr(MSP_SLP_BASE + 0xEC)
+ /* ELB single PC card detect */
+
+/* reserved 0xF0 - 0xF8 */
+#define ELB_CLK_CFG_REG regptr(MSP_SLP_BASE + 0xFC)
+ /* SDRAM read/ELB timing Reg */
+
+/* Extended UART status registers */
+#define UART0_STATUS_REG regptr(MSP_UART0_BASE + 0x0c0)
+ /* UART Status Register 0 */
+#define UART1_STATUS_REG regptr(MSP_UART1_BASE + 0x170)
+ /* UART Status Register 1 */
+
+/* Performance monitoring registers */
+#define PERF_MON_CTRL_REG regptr(MSP_SLP_BASE + 0x140)
+ /* Performance monitor control */
+#define PERF_MON_CLR_REG regptr(MSP_SLP_BASE + 0x144)
+ /* Performance monitor clear */
+#define PERF_MON_CNTH_REG regptr(MSP_SLP_BASE + 0x148)
+ /* Perf monitor counter high */
+#define PERF_MON_CNTL_REG regptr(MSP_SLP_BASE + 0x14C)
+ /* Perf monitor counter low */
+
+/* System control registers */
+#define SYS_CTRL_REG regptr(MSP_SLP_BASE + 0x150)
+ /* System control register */
+#define SYS_ERR1_REG regptr(MSP_SLP_BASE + 0x154)
+ /* System Error status 1 */
+#define SYS_ERR2_REG regptr(MSP_SLP_BASE + 0x158)
+ /* System Error status 2 */
+#define SYS_INT_CFG_REG regptr(MSP_SLP_BASE + 0x15C)
+ /* System Interrupt config */
+
+/* Voice Engine Memory configuration */
+#define VE_MEM_REG regptr(MSP_SLP_BASE + 0x17C)
+ /* Voice engine memory config */
+
+/* CPU/SLP Error Status registers */
+#define CPU_ERR1_REG regptr(MSP_SLP_BASE + 0x180)
+ /* CPU/SLP Error status 1 */
+#define CPU_ERR2_REG regptr(MSP_SLP_BASE + 0x184)
+ /* CPU/SLP Error status 1 */
+
+#define EXTENDED_GPIO_REG regptr(MSP_SLP_BASE + 0x188)
+ /* Extended GPIO register */
+
+/* System Error registers */
+#define SLP_ERR_STS_REG regptr(MSP_SLP_BASE + 0x190)
+ /* Int status for SLP errors */
+#define SLP_ERR_MSK_REG regptr(MSP_SLP_BASE + 0x194)
+ /* Int mask for SLP errors */
+#define SLP_ELB_ERST_REG regptr(MSP_SLP_BASE + 0x198)
+ /* External ELB reset */
+#define SLP_BOOT_STS_REG regptr(MSP_SLP_BASE + 0x19C)
+ /* Boot Status */
+
+/* Extended ELB addressing */
+#define CS0_EXT_ADDR_REG regptr(MSP_SLP_BASE + 0x1A0)
+ /* CS0 Extended address */
+#define CS1_EXT_ADDR_REG regptr(MSP_SLP_BASE + 0x1A4)
+ /* CS1 Extended address */
+#define CS2_EXT_ADDR_REG regptr(MSP_SLP_BASE + 0x1A8)
+ /* CS2 Extended address */
+#define CS3_EXT_ADDR_REG regptr(MSP_SLP_BASE + 0x1AC)
+ /* CS3 Extended address */
+/* reserved 0x1B0 */
+#define CS5_EXT_ADDR_REG regptr(MSP_SLP_BASE + 0x1B4)
+ /* CS5 Extended address */
+
+/* PLL Adjustment registers */
+#define PLL_LOCK_REG regptr(MSP_SLP_BASE + 0x200)
+ /* PLL0 lock status */
+#define PLL_ARST_REG regptr(MSP_SLP_BASE + 0x204)
+ /* PLL Analog reset status */
+#define PLL0_ADJ_REG regptr(MSP_SLP_BASE + 0x208)
+ /* PLL0 Adjustment value */
+#define PLL1_ADJ_REG regptr(MSP_SLP_BASE + 0x20C)
+ /* PLL1 Adjustment value */
+
+/*
+ ***************************************************************************
+ * Peripheral Register definitions *
+ ***************************************************************************
+ */
+
+/* Peripheral status */
+#define PER_CTRL_REG regptr(MSP_PER_BASE + 0x50)
+ /* Peripheral control register */
+#define PER_STS_REG regptr(MSP_PER_BASE + 0x54)
+ /* Peripheral status register */
+
+/* SPI/MPI Registers */
+#define SMPI_TX_SZ_REG regptr(MSP_PER_BASE + 0x58)
+ /* SPI/MPI Tx Size register */
+#define SMPI_RX_SZ_REG regptr(MSP_PER_BASE + 0x5C)
+ /* SPI/MPI Rx Size register */
+#define SMPI_CTL_REG regptr(MSP_PER_BASE + 0x60)
+ /* SPI/MPI Control register */
+#define SMPI_MS_REG regptr(MSP_PER_BASE + 0x64)
+ /* SPI/MPI Chip Select reg */
+#define SMPI_CORE_DATA_REG regptr(MSP_PER_BASE + 0xC0)
+ /* SPI/MPI Core Data reg */
+#define SMPI_CORE_CTRL_REG regptr(MSP_PER_BASE + 0xC4)
+ /* SPI/MPI Core Control reg */
+#define SMPI_CORE_STAT_REG regptr(MSP_PER_BASE + 0xC8)
+ /* SPI/MPI Core Status reg */
+#define SMPI_CORE_SSEL_REG regptr(MSP_PER_BASE + 0xCC)
+ /* SPI/MPI Core Ssel reg */
+#define SMPI_FIFO_REG regptr(MSP_PER_BASE + 0xD0)
+ /* SPI/MPI Data FIFO reg */
+
+/* Peripheral Block Error Registers */
+#define PER_ERR_STS_REG regptr(MSP_PER_BASE + 0x70)
+ /* Error Bit Status Register */
+#define PER_ERR_MSK_REG regptr(MSP_PER_BASE + 0x74)
+ /* Error Bit Mask Register */
+#define PER_HDR1_REG regptr(MSP_PER_BASE + 0x78)
+ /* Error Header 1 Register */
+#define PER_HDR2_REG regptr(MSP_PER_BASE + 0x7C)
+ /* Error Header 2 Register */
+
+/* Peripheral Block Interrupt Registers */
+#define PER_INT_STS_REG regptr(MSP_PER_BASE + 0x80)
+ /* Interrupt status register */
+#define PER_INT_MSK_REG regptr(MSP_PER_BASE + 0x84)
+ /* Interrupt Mask Register */
+#define GPIO_INT_STS_REG regptr(MSP_PER_BASE + 0x88)
+ /* GPIO interrupt status reg */
+#define GPIO_INT_MSK_REG regptr(MSP_PER_BASE + 0x8C)
+ /* GPIO interrupt MASK Reg */
+
+/* POLO GPIO registers */
+#define POLO_GPIO_DAT1_REG regptr(MSP_PER_BASE + 0x0E0)
+ /* Polo GPIO[8:0] data reg */
+#define POLO_GPIO_CFG1_REG regptr(MSP_PER_BASE + 0x0E4)
+ /* Polo GPIO[7:0] config reg */
+#define POLO_GPIO_CFG2_REG regptr(MSP_PER_BASE + 0x0E8)
+ /* Polo GPIO[15:8] config reg */
+#define POLO_GPIO_OD1_REG regptr(MSP_PER_BASE + 0x0EC)
+ /* Polo GPIO[31:0] output drive */
+#define POLO_GPIO_CFG3_REG regptr(MSP_PER_BASE + 0x170)
+ /* Polo GPIO[23:16] config reg */
+#define POLO_GPIO_DAT2_REG regptr(MSP_PER_BASE + 0x174)
+ /* Polo GPIO[15:9] data reg */
+#define POLO_GPIO_DAT3_REG regptr(MSP_PER_BASE + 0x178)
+ /* Polo GPIO[23:16] data reg */
+#define POLO_GPIO_DAT4_REG regptr(MSP_PER_BASE + 0x17C)
+ /* Polo GPIO[31:24] data reg */
+#define POLO_GPIO_DAT5_REG regptr(MSP_PER_BASE + 0x180)
+ /* Polo GPIO[39:32] data reg */
+#define POLO_GPIO_DAT6_REG regptr(MSP_PER_BASE + 0x184)
+ /* Polo GPIO[47:40] data reg */
+#define POLO_GPIO_DAT7_REG regptr(MSP_PER_BASE + 0x188)
+ /* Polo GPIO[54:48] data reg */
+#define POLO_GPIO_CFG4_REG regptr(MSP_PER_BASE + 0x18C)
+ /* Polo GPIO[31:24] config reg */
+#define POLO_GPIO_CFG5_REG regptr(MSP_PER_BASE + 0x190)
+ /* Polo GPIO[39:32] config reg */
+#define POLO_GPIO_CFG6_REG regptr(MSP_PER_BASE + 0x194)
+ /* Polo GPIO[47:40] config reg */
+#define POLO_GPIO_CFG7_REG regptr(MSP_PER_BASE + 0x198)
+ /* Polo GPIO[54:48] config reg */
+#define POLO_GPIO_OD2_REG regptr(MSP_PER_BASE + 0x19C)
+ /* Polo GPIO[54:32] output drive */
+
+/* Generic GPIO registers */
+#define GPIO_DATA1_REG regptr(MSP_PER_BASE + 0x170)
+ /* GPIO[1:0] data register */
+#define GPIO_DATA2_REG regptr(MSP_PER_BASE + 0x174)
+ /* GPIO[5:2] data register */
+#define GPIO_DATA3_REG regptr(MSP_PER_BASE + 0x178)
+ /* GPIO[9:6] data register */
+#define GPIO_DATA4_REG regptr(MSP_PER_BASE + 0x17C)
+ /* GPIO[15:10] data register */
+#define GPIO_CFG1_REG regptr(MSP_PER_BASE + 0x180)
+ /* GPIO[1:0] config register */
+#define GPIO_CFG2_REG regptr(MSP_PER_BASE + 0x184)
+ /* GPIO[5:2] config register */
+#define GPIO_CFG3_REG regptr(MSP_PER_BASE + 0x188)
+ /* GPIO[9:6] config register */
+#define GPIO_CFG4_REG regptr(MSP_PER_BASE + 0x18C)
+ /* GPIO[15:10] config register */
+#define GPIO_OD_REG regptr(MSP_PER_BASE + 0x190)
+ /* GPIO[15:0] output drive */
+
+/*
+ ***************************************************************************
+ * CPU Interface register definitions *
+ ***************************************************************************
+ */
+#define PCI_FLUSH_REG regptr(MSP_CPUIF_BASE + 0x00)
+ /* PCI-SDRAM queue flush trigger */
+#define OCP_ERR1_REG regptr(MSP_CPUIF_BASE + 0x04)
+ /* OCP Error Attribute 1 */
+#define OCP_ERR2_REG regptr(MSP_CPUIF_BASE + 0x08)
+ /* OCP Error Attribute 2 */
+#define OCP_STS_REG regptr(MSP_CPUIF_BASE + 0x0C)
+ /* OCP Error Status */
+#define CPUIF_PM_REG regptr(MSP_CPUIF_BASE + 0x10)
+ /* CPU policy configuration */
+#define CPUIF_CFG_REG regptr(MSP_CPUIF_BASE + 0x10)
+ /* Misc configuration options */
+
+/* Central Interrupt Controller Registers */
+#define MSP_CIC_BASE (MSP_CPUIF_BASE + 0x8000)
+ /* Central Interrupt registers */
+#define CIC_EXT_CFG_REG regptr(MSP_CIC_BASE + 0x00)
+ /* External interrupt config */
+#define CIC_STS_REG regptr(MSP_CIC_BASE + 0x04)
+ /* CIC Interrupt Status */
+#define CIC_VPE0_MSK_REG regptr(MSP_CIC_BASE + 0x08)
+ /* VPE0 Interrupt Mask */
+#define CIC_VPE1_MSK_REG regptr(MSP_CIC_BASE + 0x0C)
+ /* VPE1 Interrupt Mask */
+#define CIC_TC0_MSK_REG regptr(MSP_CIC_BASE + 0x10)
+ /* Thread Context 0 Int Mask */
+#define CIC_TC1_MSK_REG regptr(MSP_CIC_BASE + 0x14)
+ /* Thread Context 1 Int Mask */
+#define CIC_TC2_MSK_REG regptr(MSP_CIC_BASE + 0x18)
+ /* Thread Context 2 Int Mask */
+#define CIC_TC3_MSK_REG regptr(MSP_CIC_BASE + 0x18)
+ /* Thread Context 3 Int Mask */
+#define CIC_TC4_MSK_REG regptr(MSP_CIC_BASE + 0x18)
+ /* Thread Context 4 Int Mask */
+#define CIC_PCIMSI_STS_REG regptr(MSP_CIC_BASE + 0x18)
+#define CIC_PCIMSI_MSK_REG regptr(MSP_CIC_BASE + 0x18)
+#define CIC_PCIFLSH_REG regptr(MSP_CIC_BASE + 0x18)
+#define CIC_VPE0_SWINT_REG regptr(MSP_CIC_BASE + 0x08)
+
+
+/*
+ ***************************************************************************
+ * Memory controller registers *
+ ***************************************************************************
+ */
+#define MEM_CFG1_REG regptr(MSP_MEM_CFG_BASE + 0x00)
+#define MEM_SS_ADDR regptr(MSP_MEM_CFG_BASE + 0x00)
+#define MEM_SS_DATA regptr(MSP_MEM_CFG_BASE + 0x04)
+#define MEM_SS_WRITE regptr(MSP_MEM_CFG_BASE + 0x08)
+
+/*
+ ***************************************************************************
+ * PCI controller registers *
+ ***************************************************************************
+ */
+#define PCI_BASE_REG regptr(MSP_PCI_BASE + 0x00)
+#define PCI_CONFIG_SPACE_REG regptr(MSP_PCI_BASE + 0x800)
+#define PCI_JTAG_DEVID_REG regptr(MSP_SLP_BASE + 0x13c)
+
+/*
+ ########################################################################
+ # Register content & macro definitions #
+ ########################################################################
+ */
+
+/*
+ ***************************************************************************
+ * DEV_ID defines *
+ ***************************************************************************
+ */
+#define DEV_ID_PCI_DIS (1 << 26) /* Set if PCI disabled */
+#define DEV_ID_PCI_HOST (1 << 20) /* Set if PCI host */
+#define DEV_ID_SINGLE_PC (1 << 19) /* Set if single PC Card */
+#define DEV_ID_FAMILY (0xff << 8) /* family ID code */
+#define POLO_ZEUS_SUB_FAMILY (0x7 << 16) /* sub family for Polo/Zeus */
+
+#define MSPFPGA_ID (0x00 << 8) /* you are on your own here */
+#define MSP5000_ID (0x50 << 8)
+#define MSP4F00_ID (0x4f << 8) /* FPGA version of MSP4200 */
+#define MSP4E00_ID (0x4f << 8) /* FPGA version of MSP7120 */
+#define MSP4200_ID (0x42 << 8)
+#define MSP4000_ID (0x40 << 8)
+#define MSP2XXX_ID (0x20 << 8)
+#define MSPZEUS_ID (0x10 << 8)
+
+#define MSP2004_SUB_ID (0x0 << 16)
+#define MSP2005_SUB_ID (0x1 << 16)
+#define MSP2006_SUB_ID (0x1 << 16)
+#define MSP2007_SUB_ID (0x2 << 16)
+#define MSP2010_SUB_ID (0x3 << 16)
+#define MSP2015_SUB_ID (0x4 << 16)
+#define MSP2020_SUB_ID (0x5 << 16)
+#define MSP2100_SUB_ID (0x6 << 16)
+
+/*
+ ***************************************************************************
+ * RESET defines *
+ ***************************************************************************
+ */
+#define MSP_GR_RST (0x01 << 0) /* Global reset bit */
+#define MSP_MR_RST (0x01 << 1) /* MIPS reset bit */
+#define MSP_PD_RST (0x01 << 2) /* PVC DMA reset bit */
+#define MSP_PP_RST (0x01 << 3) /* PVC reset bit */
+/* reserved */
+#define MSP_EA_RST (0x01 << 6) /* Mac A reset bit */
+#define MSP_EB_RST (0x01 << 7) /* Mac B reset bit */
+#define MSP_SE_RST (0x01 << 8) /* Security Eng reset bit */
+#define MSP_PB_RST (0x01 << 9) /* Per block reset bit */
+#define MSP_EC_RST (0x01 << 10) /* Mac C reset bit */
+#define MSP_TW_RST (0x01 << 11) /* TWI reset bit */
+#define MSP_SPI_RST (0x01 << 12) /* SPI/MPI reset bit */
+#define MSP_U1_RST (0x01 << 13) /* UART1 reset bit */
+#define MSP_U0_RST (0x01 << 14) /* UART0 reset bit */
+
+/*
+ ***************************************************************************
+ * UART defines *
+ ***************************************************************************
+ */
+#ifndef CONFIG_MSP_FPGA
+#define MSP_BASE_BAUD 25000000
+#else
+#define MSP_BASE_BAUD 6000000
+#endif
+#define MSP_UART_REG_LEN 0x20
+
+/*
+ ***************************************************************************
+ * ELB defines *
+ ***************************************************************************
+ */
+#define PCCARD_32 0x02 /* Set if is PCCARD 32 (Cardbus) */
+#define SINGLE_PCCARD 0x01 /* Set to enable single PC card */
+
+/*
+ ***************************************************************************
+ * CIC defines *
+ ***************************************************************************
+ */
+
+/* CIC_EXT_CFG_REG */
+#define EXT_INT_POL(eirq) (1 << (eirq + 8))
+#define EXT_INT_EDGE(eirq) (1 << eirq)
+
+#define CIC_EXT_SET_TRIGGER_LEVEL(reg, eirq) (reg &= ~EXT_INT_EDGE(eirq))
+#define CIC_EXT_SET_TRIGGER_EDGE(reg, eirq) (reg |= EXT_INT_EDGE(eirq))
+#define CIC_EXT_SET_ACTIVE_HI(reg, eirq) (reg |= EXT_INT_POL(eirq))
+#define CIC_EXT_SET_ACTIVE_LO(reg, eirq) (reg &= ~EXT_INT_POL(eirq))
+#define CIC_EXT_SET_ACTIVE_RISING CIC_EXT_SET_ACTIVE_HI
+#define CIC_EXT_SET_ACTIVE_FALLING CIC_EXT_SET_ACTIVE_LO
+
+#define CIC_EXT_IS_TRIGGER_LEVEL(reg, eirq) \
+ ((reg & EXT_INT_EDGE(eirq)) == 0)
+#define CIC_EXT_IS_TRIGGER_EDGE(reg, eirq) (reg & EXT_INT_EDGE(eirq))
+#define CIC_EXT_IS_ACTIVE_HI(reg, eirq) (reg & EXT_INT_POL(eirq))
+#define CIC_EXT_IS_ACTIVE_LO(reg, eirq) \
+ ((reg & EXT_INT_POL(eirq)) == 0)
+#define CIC_EXT_IS_ACTIVE_RISING CIC_EXT_IS_ACTIVE_HI
+#define CIC_EXT_IS_ACTIVE_FALLING CIC_EXT_IS_ACTIVE_LO
+
+/*
+ ***************************************************************************
+ * Memory Controller defines *
+ ***************************************************************************
+ */
+
+/* Indirect memory controller registers */
+#define DDRC_CFG(n) (n)
+#define DDRC_DEBUG(n) (0x04 + n)
+#define DDRC_CTL(n) (0x40 + n)
+
+/* Macro to perform DDRC indirect write */
+#define DDRC_INDIRECT_WRITE(reg, mask, value) \
+({ \
+ *MEM_SS_ADDR = (((mask) & 0xf) << 8) | ((reg) & 0xff); \
+ *MEM_SS_DATA = (value); \
+ *MEM_SS_WRITE = 1; \
+})
+
+/*
+ ***************************************************************************
+ * SPI/MPI Mode *
+ ***************************************************************************
+ */
+#define SPI_MPI_RX_BUSY 0x00008000 /* SPI/MPI Receive Busy */
+#define SPI_MPI_FIFO_EMPTY 0x00004000 /* SPI/MPI Fifo Empty */
+#define SPI_MPI_TX_BUSY 0x00002000 /* SPI/MPI Transmit Busy */
+#define SPI_MPI_FIFO_FULL 0x00001000 /* SPI/MPU FIFO full */
+
+/*
+ ***************************************************************************
+ * SPI/MPI Control Register *
+ ***************************************************************************
+ */
+#define SPI_MPI_RX_START 0x00000004 /* Start receive command */
+#define SPI_MPI_FLUSH_Q 0x00000002 /* Flush SPI/MPI Queue */
+#define SPI_MPI_TX_START 0x00000001 /* Start Transmit Command */
+
+#endif /* !_ASM_MSP_REGS_H */
--- /dev/null
+/*
+ * Defines for the MSP interrupt controller.
+ *
+ * Copyright (C) 1999 MIPS Technologies, Inc. All rights reserved.
+ * Author: Carsten Langgaard, carstenl@mips.com
+ *
+ * ########################################################################
+ *
+ * This program is free software; you can distribute it and/or modify it
+ * under the terms of the GNU General Public License (Version 2) as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ * for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+ *
+ * ########################################################################
+ */
+
+#ifndef _MSP_SLP_INT_H
+#define _MSP_SLP_INT_H
+
+/*
+ * The PMC-Sierra SLP interrupts are arranged in a 3 level cascaded
+ * hierarchical system. The first level are the direct MIPS interrupts
+ * and are assigned the interrupt range 0-7. The second level is the SLM
+ * interrupt controller and is assigned the range 8-39. The third level
+ * comprises the Peripherial block, the PCI block, the PCI MSI block and
+ * the SLP. The PCI interrupts and the SLP errors are handled by the
+ * relevant subsystems so the core interrupt code needs only concern
+ * itself with the Peripheral block. These are assigned interrupts in
+ * the range 40-71.
+ */
+
+/*
+ * IRQs directly connected to CPU
+ */
+#define MSP_MIPS_INTBASE 0
+#define MSP_INT_SW0 0 /* IRQ for swint0, C_SW0 */
+#define MSP_INT_SW1 1 /* IRQ for swint1, C_SW1 */
+#define MSP_INT_MAC0 2 /* IRQ for MAC 0, C_IRQ0 */
+#define MSP_INT_MAC1 3 /* IRQ for MAC 1, C_IRQ1 */
+#define MSP_INT_C_IRQ2 4 /* Wired off, C_IRQ2 */
+#define MSP_INT_VE 5 /* IRQ for Voice Engine, C_IRQ3 */
+#define MSP_INT_SLP 6 /* IRQ for SLM block, C_IRQ4 */
+#define MSP_INT_TIMER 7 /* IRQ for the MIPS timer, C_IRQ5 */
+
+/*
+ * IRQs cascaded on CPU interrupt 4 (CAUSE bit 12, C_IRQ4)
+ * These defines should be tied to the register definition for the SLM
+ * interrupt routine. For now, just use hard-coded values.
+ */
+#define MSP_SLP_INTBASE (MSP_MIPS_INTBASE + 8)
+#define MSP_INT_EXT0 (MSP_SLP_INTBASE + 0)
+ /* External interrupt 0 */
+#define MSP_INT_EXT1 (MSP_SLP_INTBASE + 1)
+ /* External interrupt 1 */
+#define MSP_INT_EXT2 (MSP_SLP_INTBASE + 2)
+ /* External interrupt 2 */
+#define MSP_INT_EXT3 (MSP_SLP_INTBASE + 3)
+ /* External interrupt 3 */
+/* Reserved 4-7 */
+
+/*
+ *************************************************************************
+ * DANGER/DANGER/DANGER/DANGER/DANGER/DANGER/DANGER/DANGER/DANGER/DANGER *
+ * Some MSP produces have this interrupt labelled as Voice and some are *
+ * SEC mbox ... *
+ *************************************************************************
+ */
+#define MSP_INT_SLP_VE (MSP_SLP_INTBASE + 8)
+ /* Cascaded IRQ for Voice Engine*/
+#define MSP_INT_SLP_TDM (MSP_SLP_INTBASE + 9)
+ /* TDM interrupt */
+#define MSP_INT_SLP_MAC0 (MSP_SLP_INTBASE + 10)
+ /* Cascaded IRQ for MAC 0 */
+#define MSP_INT_SLP_MAC1 (MSP_SLP_INTBASE + 11)
+ /* Cascaded IRQ for MAC 1 */
+#define MSP_INT_SEC (MSP_SLP_INTBASE + 12)
+ /* IRQ for security engine */
+#define MSP_INT_PER (MSP_SLP_INTBASE + 13)
+ /* Peripheral interrupt */
+#define MSP_INT_TIMER0 (MSP_SLP_INTBASE + 14)
+ /* SLP timer 0 */
+#define MSP_INT_TIMER1 (MSP_SLP_INTBASE + 15)
+ /* SLP timer 1 */
+#define MSP_INT_TIMER2 (MSP_SLP_INTBASE + 16)
+ /* SLP timer 2 */
+#define MSP_INT_SLP_TIMER (MSP_SLP_INTBASE + 17)
+ /* Cascaded MIPS timer */
+#define MSP_INT_BLKCP (MSP_SLP_INTBASE + 18)
+ /* Block Copy */
+#define MSP_INT_UART0 (MSP_SLP_INTBASE + 19)
+ /* UART 0 */
+#define MSP_INT_PCI (MSP_SLP_INTBASE + 20)
+ /* PCI subsystem */
+#define MSP_INT_PCI_DBELL (MSP_SLP_INTBASE + 21)
+ /* PCI doorbell */
+#define MSP_INT_PCI_MSI (MSP_SLP_INTBASE + 22)
+ /* PCI Message Signal */
+#define MSP_INT_PCI_BC0 (MSP_SLP_INTBASE + 23)
+ /* PCI Block Copy 0 */
+#define MSP_INT_PCI_BC1 (MSP_SLP_INTBASE + 24)
+ /* PCI Block Copy 1 */
+#define MSP_INT_SLP_ERR (MSP_SLP_INTBASE + 25)
+ /* SLP error condition */
+#define MSP_INT_MAC2 (MSP_SLP_INTBASE + 26)
+ /* IRQ for MAC2 */
+/* Reserved 26-31 */
+
+/*
+ * IRQs cascaded on SLP PER interrupt (MSP_INT_PER)
+ */
+#define MSP_PER_INTBASE (MSP_SLP_INTBASE + 32)
+/* Reserved 0-1 */
+#define MSP_INT_UART1 (MSP_PER_INTBASE + 2)
+ /* UART 1 */
+/* Reserved 3-5 */
+#define MSP_INT_2WIRE (MSP_PER_INTBASE + 6)
+ /* 2-wire */
+#define MSP_INT_TM0 (MSP_PER_INTBASE + 7)
+ /* Peripheral timer block out 0 */
+#define MSP_INT_TM1 (MSP_PER_INTBASE + 8)
+ /* Peripheral timer block out 1 */
+/* Reserved 9 */
+#define MSP_INT_SPRX (MSP_PER_INTBASE + 10)
+ /* SPI RX complete */
+#define MSP_INT_SPTX (MSP_PER_INTBASE + 11)
+ /* SPI TX complete */
+#define MSP_INT_GPIO (MSP_PER_INTBASE + 12)
+ /* GPIO */
+#define MSP_INT_PER_ERR (MSP_PER_INTBASE + 13)
+ /* Peripheral error */
+/* Reserved 14-31 */
+
+#endif /* !_MSP_SLP_INT_H */
projects / linux-2.6 / commitdiff