]> err.no Git - linux-2.6/commitdiff
[PATCH] pata_ali: suspend/resume support
authorAlan <alan@lxorguk.ukuu.org.uk>
Wed, 22 Nov 2006 17:26:06 +0000 (17:26 +0000)
committerJeff Garzik <jeff@garzik.org>
Sat, 2 Dec 2006 03:46:44 +0000 (22:46 -0500)
Various chipset functions must be reprogrammed on a resume from RAM,
without this things like ATAPI DMA stop working on resume with some
chipset variants. Split the chipset programming and init time method selection into two functions.

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
drivers/ata/pata_ali.c

index e6d2b840e8706ad5e32ab9337fe72d1f428420ac..ae6d573574cd4f4aa585792279e00c73d01c5da2 100644 (file)
@@ -34,7 +34,7 @@
 #include <linux/dmi.h>
 
 #define DRV_NAME "pata_ali"
-#define DRV_VERSION "0.6.6"
+#define DRV_VERSION "0.7.1"
 
 /*
  *     Cable special cases
@@ -348,6 +348,8 @@ static struct scsi_host_template ali_sht = {
        .slave_configure        = ata_scsi_slave_config,
        .slave_destroy          = ata_scsi_slave_destroy,
        .bios_param             = ata_std_bios_param,
+       .resume                 = ata_scsi_device_resume,
+       .suspend                = ata_scsi_device_suspend,
 };
 
 /*
@@ -497,6 +499,69 @@ static struct ata_port_operations ali_c5_port_ops = {
        .host_stop      = ata_host_stop
 };
 
+
+/**
+ *     ali_init_chipset        -       chip setup function
+ *     @pdev: PCI device of ATA controller
+ *
+ *     Perform the setup on the device that must be done both at boot
+ *     and at resume time.
+ */
+static void ali_init_chipset(struct pci_dev *pdev)
+{
+       u8 rev, tmp;
+       struct pci_dev *north, *isa_bridge;
+
+       pci_read_config_byte(pdev, PCI_REVISION_ID, &rev);
+
+       /*
+        * The chipset revision selects the driver operations and
+        * mode data.
+        */
+
+       if (rev >= 0x20 && rev < 0xC2) {
+               /* 1543-E/F, 1543C-C, 1543C-D, 1543C-E */
+               pci_read_config_byte(pdev, 0x4B, &tmp);
+               /* Clear CD-ROM DMA write bit */
+               tmp &= 0x7F;
+               pci_write_config_byte(pdev, 0x4B, tmp);
+       } else if (rev >= 0xC2) {
+               /* Enable cable detection logic */
+               pci_read_config_byte(pdev, 0x4B, &tmp);
+               pci_write_config_byte(pdev, 0x4B, tmp | 0x08);
+       }
+       north = pci_get_slot(pdev->bus, PCI_DEVFN(0,0));
+       isa_bridge = pci_get_device(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1533, NULL);
+
+       if (north && north->vendor == PCI_VENDOR_ID_AL && isa_bridge) {
+               /* Configure the ALi bridge logic. For non ALi rely on BIOS.
+                  Set the south bridge enable bit */
+               pci_read_config_byte(isa_bridge, 0x79, &tmp);
+               if (rev == 0xC2)
+                       pci_write_config_byte(isa_bridge, 0x79, tmp | 0x04);
+               else if (rev > 0xC2)
+                       pci_write_config_byte(isa_bridge, 0x79, tmp | 0x02);
+       }
+       if (rev >= 0x20) {
+               /*
+                * CD_ROM DMA on (0x53 bit 0). Enable this even if we want
+                * to use PIO. 0x53 bit 1 (rev 20 only) - enable FIFO control
+                * via 0x54/55.
+                */
+               pci_read_config_byte(pdev, 0x53, &tmp);
+               if (rev <= 0x20)
+                       tmp &= ~0x02;
+               if (rev >= 0xc7)
+                       tmp |= 0x03;
+               else
+                       tmp |= 0x01;    /* CD_ROM enable for DMA */
+               pci_write_config_byte(pdev, 0x53, tmp);
+       }
+       pci_dev_put(isa_bridge);
+       pci_dev_put(north);
+       ata_pci_clear_simplex(pdev);
+}
 /**
  *     ali_init_one            -       discovery callback
  *     @pdev: PCI device ID
@@ -570,7 +635,7 @@ static int ali_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
 
        static struct ata_port_info *port_info[2];
        u8 rev, tmp;
-       struct pci_dev *north, *isa_bridge;
+       struct pci_dev *isa_bridge;
 
        pci_read_config_byte(pdev, PCI_REVISION_ID, &rev);
 
@@ -582,11 +647,6 @@ static int ali_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
        if (rev < 0x20) {
                port_info[0] = port_info[1] = &info_early;
        } else if (rev < 0xC2) {
-               /* 1543-E/F, 1543C-C, 1543C-D, 1543C-E */
-               pci_read_config_byte(pdev, 0x4B, &tmp);
-               /* Clear CD-ROM DMA write bit */
-               tmp &= 0x7F;
-               pci_write_config_byte(pdev, 0x4B, tmp);
                port_info[0] = port_info[1] = &info_20;
        } else if (rev == 0xC2) {
                port_info[0] = port_info[1] = &info_c2;
@@ -597,54 +657,25 @@ static int ali_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
        } else
                port_info[0] = port_info[1] = &info_c5;
 
-       if (rev >= 0xC2) {
-               /* Enable cable detection logic */
-               pci_read_config_byte(pdev, 0x4B, &tmp);
-               pci_write_config_byte(pdev, 0x4B, tmp | 0x08);
-       }
-
-       north = pci_get_slot(pdev->bus, PCI_DEVFN(0,0));
+       ali_init_chipset(pdev);
+       
        isa_bridge = pci_get_device(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1533, NULL);
-
-       if (north && north->vendor == PCI_VENDOR_ID_AL) {
-               /* Configure the ALi bridge logic. For non ALi rely on BIOS.
-                  Set the south bridge enable bit */
-               pci_read_config_byte(isa_bridge, 0x79, &tmp);
-               if (rev == 0xC2)
-                       pci_write_config_byte(isa_bridge, 0x79, tmp | 0x04);
-               else if (rev > 0xC2)
-                       pci_write_config_byte(isa_bridge, 0x79, tmp | 0x02);
+       if (isa_bridge && rev >= 0x20 && rev < 0xC2) {
+               /* Are we paired with a UDMA capable chip */
+               pci_read_config_byte(isa_bridge, 0x5E, &tmp);
+               if ((tmp & 0x1E) == 0x12)
+                       port_info[0] = port_info[1] = &info_20_udma;
+               pci_dev_put(isa_bridge);
        }
-
-       if (rev >= 0x20) {
-               if (rev < 0xC2) {
-                       /* Are we paired with a UDMA capable chip */
-                       pci_read_config_byte(isa_bridge, 0x5E, &tmp);
-                       if ((tmp & 0x1E) == 0x12)
-                               port_info[0] = port_info[1] = &info_20_udma;
-               }
-               /*
-                * CD_ROM DMA on (0x53 bit 0). Enable this even if we want
-                * to use PIO. 0x53 bit 1 (rev 20 only) - enable FIFO control
-                * via 0x54/55.
-                */
-               pci_read_config_byte(pdev, 0x53, &tmp);
-               if (rev <= 0x20)
-                       tmp &= ~0x02;
-               if (rev >= 0xc7)
-                       tmp |= 0x03;
-               else
-                       tmp |= 0x01;    /* CD_ROM enable for DMA */
-               pci_write_config_byte(pdev, 0x53, tmp);
-       }
-
-       pci_dev_put(isa_bridge);
-       pci_dev_put(north);
-
-       ata_pci_clear_simplex(pdev);
        return ata_pci_init_one(pdev, port_info, 2);
 }
 
+static int ali_reinit_one(struct pci_dev *pdev)
+{
+       ali_init_chipset(pdev);
+       return ata_pci_device_resume(pdev);
+}
+
 static const struct pci_device_id ali[] = {
        { PCI_VDEVICE(AL, PCI_DEVICE_ID_AL_M5228), },
        { PCI_VDEVICE(AL, PCI_DEVICE_ID_AL_M5229), },
@@ -656,7 +687,9 @@ static struct pci_driver ali_pci_driver = {
        .name           = DRV_NAME,
        .id_table       = ali,
        .probe          = ali_init_one,
-       .remove         = ata_pci_remove_one
+       .remove         = ata_pci_remove_one,
+       .suspend        = ata_pci_device_suspend,
+       .resume         = ali_reinit_one,
 };
 
 static int __init ali_init(void)