+++ /dev/null
-#include <linux/module.h>
-#include <linux/smp.h>
-#include <linux/delay.h>
-
-#include <asm/io.h>
-#include "piix4.h"
-
-void (*pm_power_off)(void);
-EXPORT_SYMBOL(pm_power_off);
-
-void machine_shutdown(void)
-{
-#ifdef CONFIG_SMP
- smp_send_stop();
-#endif
-}
-
-void machine_emergency_restart(void)
-{
- /*
- * Visual Workstations restart after this
- * register is poked on the PIIX4
- */
- outb(PIIX4_RESET_VAL, PIIX4_RESET_PORT);
-}
-
-void machine_restart(char * __unused)
-{
- machine_shutdown();
- machine_emergency_restart();
-}
-
-void machine_power_off(void)
-{
- unsigned short pm_status;
-/* extern unsigned int pci_bus0; */
-
- while ((pm_status = inw(PMSTS_PORT)) & 0x100)
- outw(pm_status, PMSTS_PORT);
-
- outw(PM_SUSPEND_ENABLE, PMCNTRL_PORT);
-
- mdelay(10);
-
-#define PCI_CONF1_ADDRESS(bus, devfn, reg) \
- (0x80000000 | (bus << 16) | (devfn << 8) | (reg & ~3))
-
-/* outl(PCI_CONF1_ADDRESS(pci_bus0, SPECIAL_DEV, SPECIAL_REG), 0xCF8); */
- outl(PIIX_SPECIAL_STOP, 0xCFC);
-}
-
-void machine_halt(void)
-{
-}
-
#include <asm/e820.h>
#include <asm/setup.h>
+/*
+ * Any quirks to be performed to initialize timers/irqs/etc?
+ */
+int (*arch_time_init_quirk)(void);
+int (*arch_pre_intr_init_quirk)(void);
+int (*arch_intr_init_quirk)(void);
+int (*arch_trap_init_quirk)(void);
+
#ifdef CONFIG_HOTPLUG_CPU
#define DEFAULT_SEND_IPI (1)
#else
**/
void __init pre_intr_init_hook(void)
{
+ if (arch_pre_intr_init_quirk) {
+ if (arch_pre_intr_init_quirk())
+ return;
+ }
init_ISA_irqs();
}
**/
void __init intr_init_hook(void)
{
+ if (arch_intr_init_quirk) {
+ if (arch_intr_init_quirk())
+ return;
+ }
#ifdef CONFIG_X86_LOCAL_APIC
apic_intr_init();
#endif
**/
void __init trap_init_hook(void)
{
+ if (arch_trap_init_quirk) {
+ if (arch_trap_init_quirk())
+ return;
+ }
}
static struct irqaction irq0 = {
**/
void __init time_init_hook(void)
{
+ if (arch_time_init_quirk) {
+ /*
+ * A nonzero return code does not mean failure, it means
+ * that the architecture quirk does not want any
+ * generic (timer) setup to be performed after this:
+ */
+ if (arch_time_init_quirk())
+ return;
+ }
+
irq0.mask = cpumask_of_cpu(0);
setup_irq(0, &irq0);
}
--- /dev/null
+/*
+ * Unmaintained SGI Visual Workstation support.
+ * Split out from setup.c by davej@suse.de
+ */
+
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/smp.h>
+
+#include <asm/arch_hooks.h>
+#include <asm/fixmap.h>
+#include <asm/reboot.h>
+#include <asm/setup.h>
+#include <asm/e820.h>
+#include <asm/io.h>
+
+#include <mach_ipi.h>
+
+#include "cobalt.h"
+#include "piix4.h"
+
+char visws_board_type = -1;
+char visws_board_rev = -1;
+
+static int __init visws_time_init_quirk(void)
+{
+ printk(KERN_INFO "Starting Cobalt Timer system clock\n");
+
+ /* Set the countdown value */
+ co_cpu_write(CO_CPU_TIMEVAL, CO_TIME_HZ/HZ);
+
+ /* Start the timer */
+ co_cpu_write(CO_CPU_CTRL, co_cpu_read(CO_CPU_CTRL) | CO_CTRL_TIMERUN);
+
+ /* Enable (unmask) the timer interrupt */
+ co_cpu_write(CO_CPU_CTRL, co_cpu_read(CO_CPU_CTRL) & ~CO_CTRL_TIMEMASK);
+
+ /*
+ * Zero return means the generic timer setup code will set up
+ * the standard vector:
+ */
+ return 0;
+}
+
+static int __init visws_pre_intr_init_quirk(void)
+{
+ init_VISWS_APIC_irqs();
+
+ /*
+ * We dont want ISA irqs to be set up by the generic code:
+ */
+ return 1;
+}
+
+/* Quirk for machine specific memory setup. */
+
+#define MB (1024 * 1024)
+
+unsigned long sgivwfb_mem_phys;
+unsigned long sgivwfb_mem_size;
+EXPORT_SYMBOL(sgivwfb_mem_phys);
+EXPORT_SYMBOL(sgivwfb_mem_size);
+
+long long mem_size __initdata = 0;
+
+static char * __init visws_memory_setup_quirk(void)
+{
+ long long gfx_mem_size = 8 * MB;
+
+ mem_size = boot_params.alt_mem_k;
+
+ if (!mem_size) {
+ printk(KERN_WARNING "Bootloader didn't set memory size, upgrade it !\n");
+ mem_size = 128 * MB;
+ }
+
+ /*
+ * this hardcodes the graphics memory to 8 MB
+ * it really should be sized dynamically (or at least
+ * set as a boot param)
+ */
+ if (!sgivwfb_mem_size) {
+ printk(KERN_WARNING "Defaulting to 8 MB framebuffer size\n");
+ sgivwfb_mem_size = 8 * MB;
+ }
+
+ /*
+ * Trim to nearest MB
+ */
+ sgivwfb_mem_size &= ~((1 << 20) - 1);
+ sgivwfb_mem_phys = mem_size - gfx_mem_size;
+
+ e820_add_region(0, LOWMEMSIZE(), E820_RAM);
+ e820_add_region(HIGH_MEMORY, mem_size - sgivwfb_mem_size - HIGH_MEMORY, E820_RAM);
+ e820_add_region(sgivwfb_mem_phys, sgivwfb_mem_size, E820_RESERVED);
+
+ return "PROM";
+}
+
+static void visws_machine_emergency_restart(void)
+{
+ /*
+ * Visual Workstations restart after this
+ * register is poked on the PIIX4
+ */
+ outb(PIIX4_RESET_VAL, PIIX4_RESET_PORT);
+}
+
+static void visws_machine_power_off(void)
+{
+ unsigned short pm_status;
+/* extern unsigned int pci_bus0; */
+
+ while ((pm_status = inw(PMSTS_PORT)) & 0x100)
+ outw(pm_status, PMSTS_PORT);
+
+ outw(PM_SUSPEND_ENABLE, PMCNTRL_PORT);
+
+ mdelay(10);
+
+#define PCI_CONF1_ADDRESS(bus, devfn, reg) \
+ (0x80000000 | (bus << 16) | (devfn << 8) | (reg & ~3))
+
+/* outl(PCI_CONF1_ADDRESS(pci_bus0, SPECIAL_DEV, SPECIAL_REG), 0xCF8); */
+ outl(PIIX_SPECIAL_STOP, 0xCFC);
+}
+
+extern int visws_trap_init_quirk(void);
+
+void __init visws_early_detect(void)
+{
+ int raw;
+
+ visws_board_type = (char)(inb_p(PIIX_GPI_BD_REG) & PIIX_GPI_BD_REG)
+ >> PIIX_GPI_BD_SHIFT;
+
+ if (visws_board_type < 0)
+ return;
+
+ /*
+ * Install special quirks for timer, interrupt and memory setup:
+ */
+ arch_time_init_quirk = visws_time_init_quirk;
+ arch_pre_intr_init_quirk = visws_pre_intr_init_quirk;
+ arch_memory_setup_quirk = visws_memory_setup_quirk;
+
+ /*
+ * Fall back to generic behavior for traps:
+ */
+ arch_intr_init_quirk = NULL;
+ arch_trap_init_quirk = visws_trap_init_quirk;
+
+ /*
+ * Install reboot quirks:
+ */
+ pm_power_off = visws_machine_power_off;
+ machine_ops.emergency_restart = visws_machine_emergency_restart;
+
+ /*
+ * Do not use broadcast IPIs:
+ */
+ no_broadcast = 0;
+
+ /*
+ * Get Board rev.
+ * First, we have to initialize the 307 part to allow us access
+ * to the GPIO registers. Let's map them at 0x0fc0 which is right
+ * after the PIIX4 PM section.
+ */
+ outb_p(SIO_DEV_SEL, SIO_INDEX);
+ outb_p(SIO_GP_DEV, SIO_DATA); /* Talk to GPIO regs. */
+
+ outb_p(SIO_DEV_MSB, SIO_INDEX);
+ outb_p(SIO_GP_MSB, SIO_DATA); /* MSB of GPIO base address */
+
+ outb_p(SIO_DEV_LSB, SIO_INDEX);
+ outb_p(SIO_GP_LSB, SIO_DATA); /* LSB of GPIO base address */
+
+ outb_p(SIO_DEV_ENB, SIO_INDEX);
+ outb_p(1, SIO_DATA); /* Enable GPIO registers. */
+
+ /*
+ * Now, we have to map the power management section to write
+ * a bit which enables access to the GPIO registers.
+ * What lunatic came up with this shit?
+ */
+ outb_p(SIO_DEV_SEL, SIO_INDEX);
+ outb_p(SIO_PM_DEV, SIO_DATA); /* Talk to GPIO regs. */
+
+ outb_p(SIO_DEV_MSB, SIO_INDEX);
+ outb_p(SIO_PM_MSB, SIO_DATA); /* MSB of PM base address */
+
+ outb_p(SIO_DEV_LSB, SIO_INDEX);
+ outb_p(SIO_PM_LSB, SIO_DATA); /* LSB of PM base address */
+
+ outb_p(SIO_DEV_ENB, SIO_INDEX);
+ outb_p(1, SIO_DATA); /* Enable PM registers. */
+
+ /*
+ * Now, write the PM register which enables the GPIO registers.
+ */
+ outb_p(SIO_PM_FER2, SIO_PM_INDEX);
+ outb_p(SIO_PM_GP_EN, SIO_PM_DATA);
+
+ /*
+ * Now, initialize the GPIO registers.
+ * We want them all to be inputs which is the
+ * power on default, so let's leave them alone.
+ * So, let's just read the board rev!
+ */
+ raw = inb_p(SIO_GP_DATA1);
+ raw &= 0x7f; /* 7 bits of valid board revision ID. */
+
+ if (visws_board_type == VISWS_320) {
+ if (raw < 0x6) {
+ visws_board_rev = 4;
+ } else if (raw < 0xc) {
+ visws_board_rev = 5;
+ } else {
+ visws_board_rev = 6;
+ }
+ } else if (visws_board_type == VISWS_540) {
+ visws_board_rev = 2;
+ } else {
+ visws_board_rev = raw;
+ }
+
+ printk(KERN_INFO "Silicon Graphics Visual Workstation %s (rev %d) detected\n",
+ (visws_board_type == VISWS_320 ? "320" :
+ (visws_board_type == VISWS_540 ? "540" :
+ "unknown")), visws_board_rev);
+}
projects / linux-2.6 / commitdiff