[PATCH] I2C: documentation update 1/3

This patch just changes the extension of Documentation/i2c/chips/smsc47b397.txt
to none - to conform with naming in i2c subsystem directory.

Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

diff --git a/Documentation/i2c/chips/smsc47b397.txt b/Documentation/i2c/chips/smsc47b397
similarity index 90%
rename from Documentation/i2c/chips/smsc47b397.txt
rename to Documentation/i2c/chips/smsc47b397
index 389edae7f8df7cefff3e60d172073917eadbb861..4737bb6109dacf234bb994035b48b4198b1a2fd3 100644 (file)
--- a/Documentation/i2c/chips/smsc47b397.txt
+++ b/Documentation/i2c/chips/smsc47b397
@@ -72,20 +72,20 @@ To program the configuration registers, the following sequence must be followed:
 
 Enter Configuration Mode
 To place the chip into the Configuration State The config key (0x55) is written
-to the CONFIG PORT (0x2E). 
+to the CONFIG PORT (0x2E).
 
 Configuration Mode
 In configuration mode, the INDEX PORT is located at the CONFIG PORT address and
 the DATA PORT is at INDEX PORT address + 1.
 
-The desired configuration registers are accessed in two steps: 
+The desired configuration registers are accessed in two steps:
 a.     Write the index of the Logical Device Number Configuration Register
        (i.e., 0x07) to the INDEX PORT and then write the number of the
        desired logical device to the DATA PORT.
 
 b.     Write the address of the desired configuration register within the
        logical device to the INDEX PORT and then write or read the config-
-       uration register through the DATA PORT.  
+       uration register through the DATA PORT.
 
 Note: If accessing the Global Configuration Registers, step (a) is not required.
 
@@ -96,18 +96,18 @@ The chip returns to the RUN State.  (This is important).
 Programming Example
 The following is an example of how to read the SIO Device ID located at 0x20
 
-; ENTER CONFIGURATION MODE   
+; ENTER CONFIGURATION MODE
 MOV    DX,02EH
 MOV    AX,055H
 OUT    DX,AL
-; GLOBAL CONFIGURATION  REGISTER 
+; GLOBAL CONFIGURATION  REGISTER
 MOV    DX,02EH
 MOV    AL,20H
-OUT    DX,AL 
+OUT    DX,AL
 ; READ THE DATA
 MOV    DX,02FH
 IN     AL,DX
-; EXIT CONFIGURATION MODE     
+; EXIT CONFIGURATION MODE
 MOV    DX,02EH
 MOV    AX,0AAH
 OUT    DX,AL
@@ -122,12 +122,12 @@ Obtaining the HWM Base Address.
 The following is an example of how to read the HWM Base Address located in
 Logical Device 8.
 
-; ENTER CONFIGURATION MODE   
+; ENTER CONFIGURATION MODE
 MOV    DX,02EH
 MOV    AX,055H
 OUT    DX,AL
-; CONFIGURE REGISTER CRE0,   
-; LOGICAL DEVICE 8           
+; CONFIGURE REGISTER CRE0,
+; LOGICAL DEVICE 8
 MOV    DX,02EH
 MOV    AL,07H
 OUT    DX,AL ;Point to LD# Config Reg
@@ -135,12 +135,12 @@ MOV       DX,02FH
 MOV    AL, 08H
 OUT    DX,AL;Point to Logical Device 8
 ;
-MOV    DX,02EH 
+MOV    DX,02EH
 MOV    AL,60H
 OUT    DX,AL   ; Point to HWM Base Addr MSB
 MOV    DX,02FH
 IN     AL,DX   ; Get MSB of HWM Base Addr
-; EXIT CONFIGURATION MODE     
+; EXIT CONFIGURATION MODE
 MOV    DX,02EH
 MOV    AX,0AAH
 OUT    DX,AL