APIC APIC support is enabled.
APM Advanced Power Management support is enabled.
AX25 Appropriate AX.25 support is enabled.
+ BLACKFIN Blackfin architecture is enabled.
DRM Direct Rendering Management support is enabled.
EDD BIOS Enhanced Disk Drive Services (EDD) is enabled
EFI EFI Partitioning (GPT) is enabled
dtc3181e= [HW,SCSI]
- earlyprintk= [X86-32,X86-64,SH]
+ earlyprintk= [X86-32,X86-64,SH,BLACKFIN]
earlyprintk=vga
earlyprintk=serial[,ttySn[,baudrate]]
S: Maintained
BLACKFIN ARCHITECTURE
-P: Aubrey Li
-M: aubrey.li@analog.com
-P: Bernd Schmidt
-M: bernd.schmidt@analog.com
P: Bryan Wu
M: bryan.wu@analog.com
-P: Grace Pan
-M: grace.pan@analog.com
-P: Marc Hoffman
-M: marc.hoffman@analog.com
-P: Michael Hennerich
-M: michael.hennerich@analog.com
-P: Mike Frysinger
-M: michael.frysinger@analog.com
-P: Jerry Zeng
-M: jerry.zeng@analog.com
-P: Jie Zhang
-M: jie.zhang@analog.com
-P: Robin Getz
-M: robin.getz@analog.com
-P: Roy Huang
-M: roy.huang@analog.com
-P: Sonic Zhang
-M: sonic.zhang@analog.com
-P: Vivi Li
-M: vivi.li@analog.com
-P: Yi Li
-M: yi.li@analog.com
L: uclinux-dist-devel@blackfin.uclinux.org (subscribers-only)
W: http://blackfin.uclinux.org
S: Supported
bool
default n
-config GENERIC_CALIBRATE_DELAY
+config GENERIC_GPIO
bool
default y
to the kernel, you may specify one here. As a minimum, you should specify
the memory size and the root device (e.g., mem=8M, root=/dev/nfs).
-comment "Board Setup"
+comment "Clock/PLL Setup"
config CLKIN_HZ
int "Crystal Frequency in Hz"
help
The frequency of CLKIN crystal oscillator on the board in Hz.
+config BFIN_KERNEL_CLOCK
+ bool "Re-program Clocks while Kernel boots?"
+ default n
+ help
+ This option decides if kernel clocks are re-programed from the
+ bootloader settings. If the clocks are not set, the SDRAM settings
+ are also not changed, and the Bootloader does 100% of the hardware
+ configuration.
+
+config PLL_BYPASS
+ bool "Bypass PLL"
+ depends on BFIN_KERNEL_CLOCK
+ default n
+
+config CLKIN_HALF
+ bool "Half Clock In"
+ depends on BFIN_KERNEL_CLOCK && (! PLL_BYPASS)
+ default n
+ help
+ If this is set the clock will be divided by 2, before it goes to the PLL.
+
+config VCO_MULT
+ int "VCO Multiplier"
+ depends on BFIN_KERNEL_CLOCK && (! PLL_BYPASS)
+ range 1 64
+ default "22" if BFIN533_EZKIT
+ default "45" if BFIN533_STAMP
+ default "20" if BFIN537_STAMP
+ default "22" if BFIN533_BLUETECHNIX_CM
+ default "20" if BFIN537_BLUETECHNIX_CM
+ default "20" if BFIN561_BLUETECHNIX_CM
+ default "20" if BFIN561_EZKIT
+ help
+ This controls the frequency of the on-chip PLL. This can be between 1 and 64.
+ PLL Frequency = (Crystal Frequency) * (this setting)
+
+choice
+ prompt "Core Clock Divider"
+ depends on BFIN_KERNEL_CLOCK
+ default CCLK_DIV_1
+ help
+ This sets the frequency of the core. It can be 1, 2, 4 or 8
+ Core Frequency = (PLL frequency) / (this setting)
+
+config CCLK_DIV_1
+ bool "1"
+
+config CCLK_DIV_2
+ bool "2"
+
+config CCLK_DIV_4
+ bool "4"
+
+config CCLK_DIV_8
+ bool "8"
+endchoice
+
+config SCLK_DIV
+ int "System Clock Divider"
+ depends on BFIN_KERNEL_CLOCK
+ range 1 15
+ default 5 if BFIN533_EZKIT
+ default 5 if BFIN533_STAMP
+ default 4 if BFIN537_STAMP
+ default 5 if BFIN533_BLUETECHNIX_CM
+ default 4 if BFIN537_BLUETECHNIX_CM
+ default 4 if BFIN561_BLUETECHNIX_CM
+ default 5 if BFIN561_EZKIT
+ help
+ This sets the frequency of the system clock (including SDRAM or DDR).
+ This can be between 1 and 15
+ System Clock = (PLL frequency) / (this setting)
+
+#
+# Max & Min Speeds for various Chips
+#
+config MAX_VCO_HZ
+ int
+ default 600000000 if BF522
+ default 600000000 if BF525
+ default 600000000 if BF527
+ default 400000000 if BF531
+ default 400000000 if BF532
+ default 750000000 if BF533
+ default 500000000 if BF534
+ default 400000000 if BF536
+ default 600000000 if BF537
+ default 533000000 if BF538
+ default 533000000 if BF539
+ default 600000000 if BF542
+ default 533000000 if BF544
+ default 533000000 if BF549
+ default 600000000 if BF561
+
+config MIN_VCO_HZ
+ int
+ default 50000000
+
+config MAX_SCLK_HZ
+ int
+ default 133000000
+
+config MIN_SCLK_HZ
+ int
+ default 27000000
+
+comment "Kernel Timer/Scheduler"
+
+source kernel/Kconfig.hz
+
+comment "Memory Setup"
+
config MEM_SIZE
int "SDRAM Memory Size in MBytes"
default 32 if BFIN533_EZKIT
config BOOT_LOAD
hex "Kernel load address for booting"
default "0x1000"
+ range 0x1000 0x20000000
help
This option allows you to set the load address of the kernel.
This can be useful if you are on a board which has a small amount
of memory or you wish to reserve some memory at the beginning of
the address space.
- Note that you generally want to keep this value at or above 4k
- (0x1000) as this will allow the kernel to capture NULL pointer
- references.
+ Note that you need to keep this value above 4k (0x1000) as this
+ memory region is used to capture NULL pointer references as well
+ as some core kernel functions.
comment "LED Status Indicators"
depends on (BFIN533_STAMP || BFIN533_BLUETECHNIX_CM)
help
Select the LED (marked on the board) for you to blink.
+choice
+ prompt "Blackfin Exception Scratch Register"
+ default BFIN_SCRATCH_REG_RETN
+ help
+ Select the resource to reserve for the Exception handler:
+ - RETN: Non-Maskable Interrupt (NMI)
+ - RETE: Exception Return (JTAG/ICE)
+ - CYCLES: Performance counter
+
+ If you are unsure, please select "RETN".
+
+config BFIN_SCRATCH_REG_RETN
+ bool "RETN"
+ help
+ Use the RETN register in the Blackfin exception handler
+ as a stack scratch register. This means you cannot
+ safely use NMI on the Blackfin while running Linux, but
+ you can debug the system with a JTAG ICE and use the
+ CYCLES performance registers.
+
+ If you are unsure, please select "RETN".
+
+config BFIN_SCRATCH_REG_RETE
+ bool "RETE"
+ help
+ Use the RETE register in the Blackfin exception handler
+ as a stack scratch register. This means you cannot
+ safely use a JTAG ICE while debugging a Blackfin board,
+ but you can safely use the CYCLES performance registers
+ and the NMI.
+
+ If you are unsure, please select "RETN".
+
+config BFIN_SCRATCH_REG_CYCLES
+ bool "CYCLES"
+ help
+ Use the CYCLES register in the Blackfin exception handler
+ as a stack scratch register. This means you cannot
+ safely use the CYCLES performance registers on a Blackfin
+ board at anytime, but you can debug the system with a JTAG
+ ICE and use the NMI.
+
+ If you are unsure, please select "RETN".
+
+endchoice
+
#
# Sorry - but you need to put the hex address here -
#
menu "Blackfin Kernel Optimizations"
-comment "Timer Tick"
-
-source kernel/Kconfig.hz
-
comment "Memory Optimizations"
config I_ENTRY_L1
comment "Cache Support"
-config BLKFIN_CACHE
+config BFIN_ICACHE
bool "Enable ICACHE"
-config BLKFIN_DCACHE
+config BFIN_DCACHE
bool "Enable DCACHE"
-config BLKFIN_DCACHE_BANKA
+config BFIN_DCACHE_BANKA
bool "Enable only 16k BankA DCACHE - BankB is SRAM"
- depends on BLKFIN_DCACHE && !BF531
+ depends on BFIN_DCACHE && !BF531
default n
-config BLKFIN_CACHE_LOCK
- bool "Enable Cache Locking"
+config BFIN_ICACHE_LOCK
+ bool "Enable Instruction Cache Locking"
choice
prompt "Policy"
- depends on BLKFIN_DCACHE
- default BLKFIN_WB
-config BLKFIN_WB
+ depends on BFIN_DCACHE
+ default BFIN_WB
+config BFIN_WB
bool "Write back"
help
Write Back Policy:
If you are unsure of the options and you want to be safe,
then go with Write Through.
-config BLKFIN_WT
+config BFIN_WT
bool "Write through"
help
Write Back Policy:
Set the max memory pieces for the L1 SRAM allocation algorithm.
Min value is 16. Max value is 1024.
-menu "Clock Settings"
-
-
-config BFIN_KERNEL_CLOCK
- bool "Re-program Clocks while Kernel boots?"
- default n
- help
- This option decides if kernel clocks are re-programed from the
- bootloader settings. If the clocks are not set, the SDRAM settings
- are also not changed, and the Bootloader does 100% of the hardware
- configuration.
-
-config VCO_MULT
- int "VCO Multiplier"
- depends on BFIN_KERNEL_CLOCK
- default "22" if BFIN533_EZKIT
- default "45" if BFIN533_STAMP
- default "20" if BFIN537_STAMP
- default "22" if BFIN533_BLUETECHNIX_CM
- default "20" if BFIN537_BLUETECHNIX_CM
- default "20" if BFIN561_BLUETECHNIX_CM
- default "20" if BFIN561_EZKIT
-
-config CCLK_DIV
- int "Core Clock Divider"
- depends on BFIN_KERNEL_CLOCK
- default 1 if BFIN533_EZKIT
- default 1 if BFIN533_STAMP
- default 1 if BFIN537_STAMP
- default 1 if BFIN533_BLUETECHNIX_CM
- default 1 if BFIN537_BLUETECHNIX_CM
- default 1 if BFIN561_BLUETECHNIX_CM
- default 1 if BFIN561_EZKIT
-
-config SCLK_DIV
- int "System Clock Divider"
- depends on BFIN_KERNEL_CLOCK
- default 5 if BFIN533_EZKIT
- default 5 if BFIN533_STAMP
- default 4 if BFIN537_STAMP
- default 5 if BFIN533_BLUETECHNIX_CM
- default 4 if BFIN537_BLUETECHNIX_CM
- default 4 if BFIN561_BLUETECHNIX_CM
- default 5 if BFIN561_EZKIT
-
-config CLKIN_HALF
- bool "Half ClockIn"
- depends on BFIN_KERNEL_CLOCK
- default n
-
-config PLL_BYPASS
- bool "Bypass PLL"
- depends on BFIN_KERNEL_CLOCK
- default n
-
-endmenu
-
comment "Asynchonous Memory Configuration"
-menu "EBIU_AMBCTL Global Control"
+menu "EBIU_AMGCTL Global Control"
config C_AMCKEN
bool "Enable CLKOUT"
default y
also relocates the irq_panic() function to L1 memory, (which is
un-cached).
-config DEBUG_KERNEL_START
- bool "Debug Kernel Startup"
- depends on DEBUG_KERNEL
- help
- Say Y here to put in an mini-execption handler before the kernel
- replaces the bootloader exception handler. This will stop kernels
- from dieing at startup with no visible error messages.
-
-config DEBUG_SERIAL_EARLY_INIT
- bool "Initialize serial driver early"
- default n
- depends on SERIAL_BFIN
- help
- Say Y here if you want to get kernel output early when kernel
- crashes before the normal console initialization. If this option
- is enable, console output will always go to the ttyBF0, no matter
- what kernel boot paramters you set.
-
config DEBUG_HUNT_FOR_ZERO
bool "Catch NULL pointer reads/writes"
default y
Enabling this option will take up an extra entry in CPLB table.
Otherwise, there is no extra overhead.
+config DEBUG_BFIN_HWTRACE_ON
+ bool "Turn on Blackfin's Hardware Trace"
+ default y
+ help
+ All Blackfins include a Trace Unit which stores a history of the last
+ 16 changes in program flow taken by the program sequencer. The history
+ allows the user to recreate the program sequencer’s recent path. This
+ can be handy when an application dies - we print out the execution
+ path of how it got to the offending instruction.
+
+ By turning this off, you may save a tiny amount of power.
+
+choice
+ prompt "Omit loop Tracing"
+ default DEBUG_BFIN_HWTRACE_COMPRESSION_OFF
+ depends on DEBUG_BFIN_HWTRACE_ON
+ help
+ The trace buffer can be configured to omit recording of changes in
+ program flow that match either the last entry or one of the last
+ two entries. Omitting one of these entries from the record prevents
+ the trace buffer from overflowing because of any sort of loop (for, do
+ while, etc) in the program.
+
+ Because zero-overhead Hardware loops are not recorded in the trace buffer,
+ this feature can be used to prevent trace overflow from loops that
+ are nested four deep.
+
+config DEBUG_BFIN_HWTRACE_COMPRESSION_OFF
+ bool "Trace all Loops"
+ help
+ The trace buffer records all changes of flow
+
+config DEBUG_BFIN_HWTRACE_COMPRESSION_ONE
+ bool "Compress single-level loops"
+ help
+ The trace buffer does not record single loops - helpful if trace
+ is spinning on a while or do loop.
+
+config DEBUG_BFIN_HWTRACE_COMPRESSION_TWO
+ bool "Compress two-level loops"
+ help
+ The trace buffer does not record loops two levels deep. Helpful if
+ the trace is spinning in a nested loop
+
+endchoice
+
+config DEBUG_BFIN_HWTRACE_COMPRESSION
+ int
+ depends on DEBUG_BFIN_HWTRACE_ON
+ default 0 if DEBUG_BFIN_HWTRACE_COMPRESSION_OFF
+ default 1 if DEBUG_BFIN_HWTRACE_COMPRESSION_ONE
+ default 2 if DEBUG_BFIN_HWTRACE_COMPRESSION_TWO
+
+
+config DEBUG_BFIN_HWTRACE_EXPAND
+ bool "Expand Trace Buffer greater than 16 entries"
+ depends on DEBUG_BFIN_HWTRACE_ON
+ default n
+ help
+ By selecting this option, every time the 16 hardware entries in
+ the Blackfin's HW Trace buffer are full, the kernel will move them
+ into a software buffer, for dumping when there is an issue. This
+ has a great impact on performance, (an interrupt every 16 change of
+ flows) and should normally be turned off, except in those nasty
+ debugging sessions
+
+config DEBUG_BFIN_HWTRACE_EXPAND_LEN
+ int "Size of Trace buffer (in power of 2k)"
+ range 0 4
+ depends on DEBUG_BFIN_HWTRACE_EXPAND
+ default 1
+ help
+ This sets the size of the software buffer that the trace information
+ is kept in.
+ 0 for (2^0) 1k, or 256 entries,
+ 1 for (2^1) 2k, or 512 entries,
+ 2 for (2^2) 4k, or 1024 entries,
+ 3 for (2^3) 8k, or 2048 entries,
+ 4 for (2^4) 16k, or 4096 entries
+
config DEBUG_BFIN_NO_KERN_HWTRACE
bool "Trace user apps (turn off hwtrace in kernel)"
+ depends on DEBUG_BFIN_HWTRACE_ON
default n
help
Some pieces of the kernel contain a lot of flow changes which can
Say Y here to disable hardware tracing in some known "jumpy" pieces
of code so that the trace buffer will extend further back.
+config EARLY_PRINTK
+ bool "Early printk"
+ default n
+ help
+ This option enables special console drivers which allow the kernel
+ to print messages very early in the bootup process.
+
+ This is useful for kernel debugging when your machine crashes very
+ early before the console code is initialized. After enabling this
+ feature, you must add "earlyprintk=serial,uart0,57600" to the
+ command line (bootargs). It is safe to say Y here in all cases, as
+ all of this lives in the init section and is thrown away after the
+ kernel boots completely.
+
config DUAL_CORE_TEST_MODULE
tristate "Dual Core Test Module"
depends on (BF561)
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.21.5
+# Linux kernel version: 2.6.22.6
#
# CONFIG_MMU is not set
# CONFIG_FPU is not set
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
# CONFIG_GENERIC_TIME is not set
-CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_GPIO=y
CONFIG_FORCE_MAX_ZONEORDER=14
+CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_IRQCHIP_DEMUX_GPIO=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
# CONFIG_TASKSTATS is not set
# CONFIG_UTS_NS is not set
# CONFIG_AUDIT is not set
-# CONFIG_IKCONFIG is not set
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
CONFIG_SYSFS_DEPRECATED=y
# CONFIG_RELAY is not set
CONFIG_BLK_DEV_INITRD=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
+CONFIG_VM_EVENT_COUNTERS=y
CONFIG_BIG_ORDER_ALLOC_NOFAIL_MAGIC=3
-CONFIG_BUDDY=y
# CONFIG_NP2 is not set
CONFIG_SLAB=y
-CONFIG_VM_EVENT_COUNTERS=y
+# CONFIG_SLUB is not set
+# CONFIG_SLOB is not set
CONFIG_RT_MUTEXES=y
CONFIG_TINY_SHMEM=y
CONFIG_BASE_SMALL=0
-# CONFIG_SLOB is not set
#
# Loadable module support
# CONFIG_CMDLINE_BOOL is not set
#
-# Board Setup
+# Clock/PLL Setup
#
CONFIG_CLKIN_HZ=27000000
-CONFIG_MEM_SIZE=32
-CONFIG_MEM_ADD_WIDTH=9
-CONFIG_BOOT_LOAD=0x1000
-
-#
-# Blackfin Kernel Optimizations
-#
+# CONFIG_BFIN_KERNEL_CLOCK is not set
+CONFIG_MAX_VCO_HZ=750000000
+CONFIG_MIN_VCO_HZ=50000000
+CONFIG_MAX_SCLK_HZ=133000000
+CONFIG_MIN_SCLK_HZ=27000000
#
-# Timer Tick
+# Kernel Timer/Scheduler
#
# CONFIG_HZ_100 is not set
CONFIG_HZ_250=y
# CONFIG_HZ_1000 is not set
CONFIG_HZ=250
+#
+# Memory Setup
+#
+CONFIG_MEM_SIZE=32
+CONFIG_MEM_ADD_WIDTH=9
+CONFIG_BOOT_LOAD=0x1000
+CONFIG_BFIN_SCRATCH_REG_RETN=y
+# CONFIG_BFIN_SCRATCH_REG_RETE is not set
+# CONFIG_BFIN_SCRATCH_REG_CYCLES is not set
+
+#
+# Blackfin Kernel Optimizations
+#
+
#
# Memory Optimizations
#
#
# Cache Support
#
-CONFIG_BLKFIN_CACHE=y
-CONFIG_BLKFIN_DCACHE=y
-# CONFIG_BLKFIN_DCACHE_BANKA is not set
-# CONFIG_BLKFIN_CACHE_LOCK is not set
-# CONFIG_BLKFIN_WB is not set
-CONFIG_BLKFIN_WT=y
+CONFIG_BFIN_ICACHE=y
+CONFIG_BFIN_DCACHE=y
+# CONFIG_BFIN_DCACHE_BANKA is not set
+# CONFIG_BFIN_ICACHE_LOCK is not set
+# CONFIG_BFIN_WB is not set
+CONFIG_BFIN_WT=y
CONFIG_L1_MAX_PIECE=16
-#
-# Clock Settings
-#
-# CONFIG_BFIN_KERNEL_CLOCK is not set
-
#
# Asynchonous Memory Configuration
#
CONFIG_BANK_0=0x7BB0
CONFIG_BANK_1=0x7BB0
CONFIG_BANK_2=0x7BB0
-CONFIG_BANK_3=0x99B3
+CONFIG_BANK_3=0xAAC3
#
# Bus options (PCI, PCMCIA, EISA, MCA, ISA)
#
# CONFIG_PCI is not set
+# CONFIG_ARCH_SUPPORTS_MSI is not set
#
# PCCARD (PCMCIA/CardBus) support
#
# CONFIG_PCCARD is not set
-#
-# PCI Hotplug Support
-#
-
#
# Executable file formats
#
#
# Networking options
#
-# CONFIG_NETDEBUG is not set
CONFIG_PACKET=y
# CONFIG_PACKET_MMAP is not set
CONFIG_UNIX=y
# CONFIG_NETLABEL is not set
# CONFIG_NETWORK_SECMARK is not set
# CONFIG_NETFILTER is not set
-
-#
-# DCCP Configuration (EXPERIMENTAL)
-#
# CONFIG_IP_DCCP is not set
-
-#
-# SCTP Configuration (EXPERIMENTAL)
-#
# CONFIG_IP_SCTP is not set
-
-#
-# TIPC Configuration (EXPERIMENTAL)
-#
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# FIR device drivers
#
# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_MAC80211 is not set
# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
#
# Device Drivers
# Connector - unified userspace <-> kernelspace linker
#
# CONFIG_CONNECTOR is not set
-
-#
-# Memory Technology Devices (MTD)
-#
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
# CONFIG_MTD_CONCAT is not set
CONFIG_MTD_RAM=y
CONFIG_MTD_ROM=m
# CONFIG_MTD_ABSENT is not set
-# CONFIG_MTD_OBSOLETE_CHIPS is not set
#
# Mapping drivers for chip access
# CONFIG_MTD_DOC2000 is not set
# CONFIG_MTD_DOC2001 is not set
# CONFIG_MTD_DOC2001PLUS is not set
-
-#
-# NAND Flash Device Drivers
-#
# CONFIG_MTD_NAND is not set
+# CONFIG_MTD_ONENAND is not set
#
-# OneNAND Flash Device Drivers
+# UBI - Unsorted block images
#
-# CONFIG_MTD_ONENAND is not set
+# CONFIG_MTD_UBI is not set
#
# Parallel port support
#
# Misc devices
#
-
-#
-# ATA/ATAPI/MFM/RLL support
-#
# CONFIG_IDE is not set
#
# CONFIG_RAID_ATTRS is not set
# CONFIG_SCSI is not set
# CONFIG_SCSI_NETLINK is not set
-
-#
-# Serial ATA (prod) and Parallel ATA (experimental) drivers
-#
# CONFIG_ATA is not set
#
#
# CONFIG_MD is not set
-#
-# Fusion MPT device support
-#
-# CONFIG_FUSION is not set
-
-#
-# IEEE 1394 (FireWire) support
-#
-
-#
-# I2O device support
-#
-
#
# Network device support
#
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
-
-#
-# PHY device support
-#
# CONFIG_PHYLIB is not set
#
CONFIG_MII=y
CONFIG_SMC91X=y
# CONFIG_SMSC911X is not set
+# CONFIG_DM9000 is not set
+CONFIG_NETDEV_1000=y
+CONFIG_NETDEV_10000=y
#
-# Ethernet (1000 Mbit)
-#
-
-#
-# Ethernet (10000 Mbit)
-#
-
-#
-# Token Ring devices
-#
-
-#
-# Wireless LAN (non-hamradio)
-#
-# CONFIG_NET_RADIO is not set
-
-#
-# Wan interfaces
+# Wireless LAN
#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
# CONFIG_WAN is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
#
CONFIG_INPUT=m
# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
#
# Userland interfaces
# CONFIG_INPUT_KEYBOARD is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
# CONFIG_INPUT_MISC is not set
#
# CONFIG_AD9960 is not set
# CONFIG_SPI_ADC_BF533 is not set
-# CONFIG_BF5xx_PFLAGS is not set
+# CONFIG_BFIN_PFLAGS is not set
# CONFIG_BF5xx_PPIFCD is not set
# CONFIG_BF5xx_TIMERS is not set
# CONFIG_BF5xx_PPI is not set
# IPMI
#
# CONFIG_IPMI_HANDLER is not set
-
-#
-# Watchdog Cards
-#
CONFIG_WATCHDOG=y
# CONFIG_WATCHDOG_NOWAYOUT is not set
CONFIG_HW_RANDOM=y
# CONFIG_GEN_RTC is not set
CONFIG_BLACKFIN_DPMC=y
-# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_RAW_DRIVER is not set
# TPM devices
#
# CONFIG_TCG_TPM is not set
-
-#
-# I2C support
-#
# CONFIG_I2C is not set
#
# SPI Protocol Masters
#
# CONFIG_SPI_AT25 is not set
+# CONFIG_SPI_SPIDEV is not set
#
# Dallas's 1-wire bus
#
# CONFIG_W1 is not set
-
-#
-# Hardware Monitoring support
-#
CONFIG_HWMON=y
# CONFIG_HWMON_VID is not set
# CONFIG_SENSORS_ABITUGURU is not set
# CONFIG_SENSORS_F71805F is not set
# CONFIG_SENSORS_LM70 is not set
# CONFIG_SENSORS_PC87427 is not set
+# CONFIG_SENSORS_SMSC47M1 is not set
+# CONFIG_SENSORS_SMSC47B397 is not set
# CONFIG_SENSORS_VT1211 is not set
+# CONFIG_SENSORS_W83627HF is not set
# CONFIG_HWMON_DEBUG_CHIP is not set
#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+CONFIG_DAB=y
#
-# Digital Video Broadcasting Devices
+# Graphics support
#
-# CONFIG_DVB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
-# Graphics support
+# Display device support
#
-# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+# CONFIG_DISPLAY_SUPPORT is not set
+# CONFIG_VGASTATE is not set
# CONFIG_FB is not set
#
# CONFIG_USB is not set
#
-# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
+# Enable Host or Gadget support to see Inventra options
#
#
-# USB Gadget Support
+# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
#
-# CONFIG_USB_GADGET is not set
#
-# MMC/SD Card support
+# USB Gadget Support
#
-# CONFIG_SPI_MMC is not set
+# CONFIG_USB_GADGET is not set
# CONFIG_MMC is not set
#
CONFIG_RTC_INTF_PROC=y
CONFIG_RTC_INTF_DEV=y
# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set
+# CONFIG_RTC_DRV_TEST is not set
+
+#
+# I2C RTC drivers
+#
+
+#
+# SPI RTC drivers
+#
+# CONFIG_RTC_DRV_RS5C348 is not set
+# CONFIG_RTC_DRV_MAX6902 is not set
#
-# RTC drivers
+# Platform RTC drivers
#
# CONFIG_RTC_DRV_DS1553 is not set
# CONFIG_RTC_DRV_DS1742 is not set
-# CONFIG_RTC_DRV_RS5C348 is not set
# CONFIG_RTC_DRV_M48T86 is not set
-# CONFIG_RTC_DRV_TEST is not set
-# CONFIG_RTC_DRV_MAX6902 is not set
# CONFIG_RTC_DRV_V3020 is not set
+
+#
+# on-CPU RTC drivers
+#
CONFIG_RTC_DRV_BFIN=y
#
# DMA Devices
#
-#
-# Auxiliary Display support
-#
-
-#
-# Virtualization
-#
-
#
# PBX support
#
CONFIG_LOCKD_V4=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=m
+# CONFIG_SUNRPC_BIND34 is not set
# CONFIG_RPCSEC_GSS_KRB5 is not set
# CONFIG_RPCSEC_GSS_SPKM3 is not set
CONFIG_SMB_FS=m
CONFIG_ENABLE_MUST_CHECK=y
# CONFIG_MAGIC_SYSRQ is not set
# CONFIG_UNUSED_SYMBOLS is not set
-# CONFIG_DEBUG_FS is not set
+CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_KERNEL is not set
-CONFIG_LOG_BUF_SHIFT=14
# CONFIG_DEBUG_BUGVERBOSE is not set
-# CONFIG_DEBUG_SERIAL_EARLY_INIT is not set
+CONFIG_DEBUG_MMRS=y
CONFIG_DEBUG_HUNT_FOR_ZERO=y
+CONFIG_DEBUG_BFIN_HWTRACE_ON=y
+CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION_OFF=y
+# CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION_ONE is not set
+# CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION_TWO is not set
+CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION=0
+# CONFIG_DEBUG_BFIN_HWTRACE_EXPAND is not set
# CONFIG_DEBUG_BFIN_NO_KERN_HWTRACE is not set
+CONFIG_EARLY_PRINTK=y
CONFIG_CPLB_INFO=y
CONFIG_ACCESS_CHECK=y
CONFIG_BITREVERSE=y
CONFIG_CRC_CCITT=m
# CONFIG_CRC16 is not set
+# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
# CONFIG_LIBCRC32C is not set
CONFIG_ZLIB_INFLATE=y
CONFIG_PLIST=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.21.5
+# Linux kernel version: 2.6.22.6
#
# CONFIG_MMU is not set
# CONFIG_FPU is not set
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
# CONFIG_GENERIC_TIME is not set
-CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_GPIO=y
CONFIG_FORCE_MAX_ZONEORDER=14
+CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_IRQCHIP_DEMUX_GPIO=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
# CONFIG_TASKSTATS is not set
# CONFIG_UTS_NS is not set
# CONFIG_AUDIT is not set
-# CONFIG_IKCONFIG is not set
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
CONFIG_SYSFS_DEPRECATED=y
# CONFIG_RELAY is not set
CONFIG_BLK_DEV_INITRD=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
+CONFIG_VM_EVENT_COUNTERS=y
CONFIG_BIG_ORDER_ALLOC_NOFAIL_MAGIC=3
-CONFIG_BUDDY=y
# CONFIG_NP2 is not set
CONFIG_SLAB=y
-CONFIG_VM_EVENT_COUNTERS=y
+# CONFIG_SLUB is not set
+# CONFIG_SLOB is not set
CONFIG_RT_MUTEXES=y
CONFIG_TINY_SHMEM=y
CONFIG_BASE_SMALL=0
-# CONFIG_SLOB is not set
#
# Loadable module support
# CONFIG_CMDLINE_BOOL is not set
#
-# Board Setup
+# Clock/PLL Setup
#
CONFIG_CLKIN_HZ=11059200
+# CONFIG_BFIN_KERNEL_CLOCK is not set
+CONFIG_MAX_VCO_HZ=750000000
+CONFIG_MIN_VCO_HZ=50000000
+CONFIG_MAX_SCLK_HZ=133000000
+CONFIG_MIN_SCLK_HZ=27000000
+
+#
+# Kernel Timer/Scheduler
+#
+# CONFIG_HZ_100 is not set
+CONFIG_HZ_250=y
+# CONFIG_HZ_300 is not set
+# CONFIG_HZ_1000 is not set
+CONFIG_HZ=250
+
+#
+# Memory Setup
+#
CONFIG_MEM_SIZE=128
CONFIG_MEM_ADD_WIDTH=11
CONFIG_ENET_FLASH_PIN=0
#
# CONFIG_BFIN_ALIVE_LED is not set
# CONFIG_BFIN_IDLE_LED is not set
+CONFIG_BFIN_SCRATCH_REG_RETN=y
+# CONFIG_BFIN_SCRATCH_REG_RETE is not set
+# CONFIG_BFIN_SCRATCH_REG_CYCLES is not set
CONFIG_BFIN_ALIVE_LED_PORT=0xFFC00700
CONFIG_BFIN_ALIVE_LED_DPORT=0xFFC00730
CONFIG_BFIN_IDLE_LED_PORT=0xFFC00700
# Blackfin Kernel Optimizations
#
-#
-# Timer Tick
-#
-# CONFIG_HZ_100 is not set
-CONFIG_HZ_250=y
-# CONFIG_HZ_300 is not set
-# CONFIG_HZ_1000 is not set
-CONFIG_HZ=250
-
#
# Memory Optimizations
#
#
# Cache Support
#
-CONFIG_BLKFIN_CACHE=y
-CONFIG_BLKFIN_DCACHE=y
-# CONFIG_BLKFIN_DCACHE_BANKA is not set
-# CONFIG_BLKFIN_CACHE_LOCK is not set
-# CONFIG_BLKFIN_WB is not set
-CONFIG_BLKFIN_WT=y
+CONFIG_BFIN_ICACHE=y
+CONFIG_BFIN_DCACHE=y
+# CONFIG_BFIN_DCACHE_BANKA is not set
+# CONFIG_BFIN_ICACHE_LOCK is not set
+# CONFIG_BFIN_WB is not set
+CONFIG_BFIN_WT=y
CONFIG_L1_MAX_PIECE=16
-#
-# Clock Settings
-#
-# CONFIG_BFIN_KERNEL_CLOCK is not set
-
#
# Asynchonous Memory Configuration
#
CONFIG_BANK_0=0x7BB0
CONFIG_BANK_1=0x7BB0
CONFIG_BANK_2=0x7BB0
-CONFIG_BANK_3=0x99B3
+CONFIG_BANK_3=0xAAC3
#
# Bus options (PCI, PCMCIA, EISA, MCA, ISA)
#
# CONFIG_PCI is not set
+# CONFIG_ARCH_SUPPORTS_MSI is not set
#
# PCCARD (PCMCIA/CardBus) support
#
# CONFIG_PCCARD is not set
-#
-# PCI Hotplug Support
-#
-
#
# Executable file formats
#
#
# Networking options
#
-# CONFIG_NETDEBUG is not set
CONFIG_PACKET=y
# CONFIG_PACKET_MMAP is not set
CONFIG_UNIX=y
# CONFIG_NETLABEL is not set
# CONFIG_NETWORK_SECMARK is not set
# CONFIG_NETFILTER is not set
-
-#
-# DCCP Configuration (EXPERIMENTAL)
-#
# CONFIG_IP_DCCP is not set
-
-#
-# SCTP Configuration (EXPERIMENTAL)
-#
# CONFIG_IP_SCTP is not set
-
-#
-# TIPC Configuration (EXPERIMENTAL)
-#
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# FIR device drivers
#
# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_MAC80211 is not set
# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
#
# Device Drivers
# Connector - unified userspace <-> kernelspace linker
#
# CONFIG_CONNECTOR is not set
-
-#
-# Memory Technology Devices (MTD)
-#
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
# CONFIG_MTD_CONCAT is not set
CONFIG_MTD_RAM=y
CONFIG_MTD_ROM=m
# CONFIG_MTD_ABSENT is not set
-# CONFIG_MTD_OBSOLETE_CHIPS is not set
#
# Mapping drivers for chip access
# CONFIG_MTD_DOC2000 is not set
# CONFIG_MTD_DOC2001 is not set
# CONFIG_MTD_DOC2001PLUS is not set
-
-#
-# NAND Flash Device Drivers
-#
# CONFIG_MTD_NAND is not set
+# CONFIG_MTD_ONENAND is not set
#
-# OneNAND Flash Device Drivers
+# UBI - Unsorted block images
#
-# CONFIG_MTD_ONENAND is not set
+# CONFIG_MTD_UBI is not set
#
# Parallel port support
#
# Misc devices
#
-
-#
-# ATA/ATAPI/MFM/RLL support
-#
# CONFIG_IDE is not set
#
# CONFIG_RAID_ATTRS is not set
# CONFIG_SCSI is not set
# CONFIG_SCSI_NETLINK is not set
-
-#
-# Serial ATA (prod) and Parallel ATA (experimental) drivers
-#
# CONFIG_ATA is not set
#
#
# CONFIG_MD is not set
-#
-# Fusion MPT device support
-#
-# CONFIG_FUSION is not set
-
-#
-# IEEE 1394 (FireWire) support
-#
-
-#
-# I2O device support
-#
-
#
# Network device support
#
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
-
-#
-# PHY device support
-#
# CONFIG_PHYLIB is not set
#
CONFIG_MII=y
CONFIG_SMC91X=y
# CONFIG_SMSC911X is not set
+# CONFIG_DM9000 is not set
+CONFIG_NETDEV_1000=y
+CONFIG_NETDEV_10000=y
#
-# Ethernet (1000 Mbit)
-#
-
-#
-# Ethernet (10000 Mbit)
-#
-
-#
-# Token Ring devices
-#
-
-#
-# Wireless LAN (non-hamradio)
-#
-# CONFIG_NET_RADIO is not set
-
-#
-# Wan interfaces
+# Wireless LAN
#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
# CONFIG_WAN is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
#
CONFIG_INPUT=y
# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
#
# Userland interfaces
# CONFIG_INPUT_KEYBOARD is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
CONFIG_INPUT_MISC=y
+# CONFIG_INPUT_ATI_REMOTE is not set
+# CONFIG_INPUT_ATI_REMOTE2 is not set
+# CONFIG_INPUT_KEYSPAN_REMOTE is not set
+# CONFIG_INPUT_POWERMATE is not set
+# CONFIG_INPUT_YEALINK is not set
# CONFIG_INPUT_UINPUT is not set
# CONFIG_BF53X_PFBUTTONS is not set
CONFIG_TWI_KEYPAD=m
#
# CONFIG_AD9960 is not set
# CONFIG_SPI_ADC_BF533 is not set
-# CONFIG_BF5xx_PFLAGS is not set
+# CONFIG_BFIN_PFLAGS is not set
# CONFIG_BF5xx_PPIFCD is not set
# CONFIG_BF5xx_TIMERS is not set
# CONFIG_BF5xx_PPI is not set
# IPMI
#
# CONFIG_IPMI_HANDLER is not set
-
-#
-# Watchdog Cards
-#
CONFIG_WATCHDOG=y
# CONFIG_WATCHDOG_NOWAYOUT is not set
CONFIG_HW_RANDOM=y
# CONFIG_GEN_RTC is not set
CONFIG_BLACKFIN_DPMC=y
-# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_RAW_DRIVER is not set
# TPM devices
#
# CONFIG_TCG_TPM is not set
-
-#
-# I2C support
-#
CONFIG_I2C=m
+CONFIG_I2C_BOARDINFO=y
CONFIG_I2C_CHARDEV=m
#
# I2C Hardware Bus support
#
# CONFIG_I2C_BLACKFIN_GPIO is not set
+# CONFIG_I2C_GPIO is not set
# CONFIG_I2C_OCORES is not set
# CONFIG_I2C_PARPORT_LIGHT is not set
+# CONFIG_I2C_SIMTEC is not set
# CONFIG_I2C_STUB is not set
-# CONFIG_I2C_PCA_ISA is not set
#
# Miscellaneous I2C Chip support
# SPI Protocol Masters
#
# CONFIG_SPI_AT25 is not set
+# CONFIG_SPI_SPIDEV is not set
#
# Dallas's 1-wire bus
#
# CONFIG_W1 is not set
-
-#
-# Hardware Monitoring support
-#
CONFIG_HWMON=y
# CONFIG_HWMON_VID is not set
# CONFIG_SENSORS_ABITUGURU is not set
+# CONFIG_SENSORS_AD7418 is not set
# CONFIG_SENSORS_ADM1021 is not set
# CONFIG_SENSORS_ADM1025 is not set
# CONFIG_SENSORS_ADM1026 is not set
# CONFIG_SENSORS_LM90 is not set
# CONFIG_SENSORS_LM92 is not set
# CONFIG_SENSORS_MAX1619 is not set
+# CONFIG_SENSORS_MAX6650 is not set
# CONFIG_SENSORS_PC87360 is not set
# CONFIG_SENSORS_PC87427 is not set
# CONFIG_SENSORS_SMSC47M1 is not set
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+CONFIG_DAB=y
#
-# Digital Video Broadcasting Devices
+# Graphics support
#
-# CONFIG_DVB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
-# Graphics support
+# Display device support
#
-# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+# CONFIG_DISPLAY_SUPPORT is not set
+# CONFIG_VGASTATE is not set
CONFIG_FB=m
CONFIG_FIRMWARE_EDID=y
# CONFIG_FB_DDC is not set
CONFIG_FB_CFB_FILLRECT=m
CONFIG_FB_CFB_COPYAREA=m
CONFIG_FB_CFB_IMAGEBLIT=m
+# CONFIG_FB_SYS_FILLRECT is not set
+# CONFIG_FB_SYS_COPYAREA is not set
+# CONFIG_FB_SYS_IMAGEBLIT is not set
+# CONFIG_FB_SYS_FOPS is not set
+CONFIG_FB_DEFERRED_IO=y
# CONFIG_FB_SVGALIB is not set
# CONFIG_FB_MACMODES is not set
# CONFIG_FB_BACKLIGHT is not set
# CONFIG_ADV7393_2XMEM is not set
# CONFIG_FB_S1D13XXX is not set
# CONFIG_FB_VIRTUAL is not set
-
-#
-# Logo configuration
-#
# CONFIG_LOGO is not set
#
# CONFIG_SND_BLACKFIN_AD1836_I2S is not set
CONFIG_SND_BLACKFIN_AD1836_MULSUB=y
# CONFIG_SND_BLACKFIN_AD1836_5P1 is not set
-CONFIG_SND_BLACKFIN_AD1981B=m
CONFIG_SND_BLACKFIN_SPORT=0
CONFIG_SND_BLACKFIN_SPI_PFBIT=4
CONFIG_SND_BFIN_AD73311=m
CONFIG_SND_BFIN_AD73311_SE=4
#
-# SoC audio support
+# System on Chip audio support
#
# CONFIG_SND_SOC is not set
+#
+# SoC Audio for the ADI Blackfin
+#
+# CONFIG_SND_BF5XX_HAVE_COLD_RESET is not set
+
#
# Open Sound System
#
# CONFIG_USB is not set
#
-# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
+# Enable Host or Gadget support to see Inventra options
#
#
-# USB Gadget Support
+# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
#
-# CONFIG_USB_GADGET is not set
#
-# MMC/SD Card support
+# USB Gadget Support
#
-# CONFIG_SPI_MMC is not set
+# CONFIG_USB_GADGET is not set
# CONFIG_MMC is not set
#
CONFIG_RTC_INTF_PROC=y
CONFIG_RTC_INTF_DEV=y
# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set
+# CONFIG_RTC_DRV_TEST is not set
#
-# RTC drivers
+# I2C RTC drivers
#
-# CONFIG_RTC_DRV_X1205 is not set
# CONFIG_RTC_DRV_DS1307 is not set
-# CONFIG_RTC_DRV_DS1553 is not set
-# CONFIG_RTC_DRV_ISL1208 is not set
# CONFIG_RTC_DRV_DS1672 is not set
-# CONFIG_RTC_DRV_DS1742 is not set
+# CONFIG_RTC_DRV_MAX6900 is not set
+# CONFIG_RTC_DRV_RS5C372 is not set
+# CONFIG_RTC_DRV_ISL1208 is not set
+# CONFIG_RTC_DRV_X1205 is not set
# CONFIG_RTC_DRV_PCF8563 is not set
+# CONFIG_RTC_DRV_PCF8583 is not set
+
+#
+# SPI RTC drivers
+#
# CONFIG_RTC_DRV_RS5C348 is not set
-# CONFIG_RTC_DRV_RS5C372 is not set
-# CONFIG_RTC_DRV_M48T86 is not set
-# CONFIG_RTC_DRV_TEST is not set
# CONFIG_RTC_DRV_MAX6902 is not set
-# CONFIG_RTC_DRV_V3020 is not set
-CONFIG_RTC_DRV_BFIN=y
#
-# DMA Engine support
+# Platform RTC drivers
#
-# CONFIG_DMA_ENGINE is not set
+# CONFIG_RTC_DRV_DS1553 is not set
+# CONFIG_RTC_DRV_DS1742 is not set
+# CONFIG_RTC_DRV_M48T86 is not set
+# CONFIG_RTC_DRV_V3020 is not set
#
-# DMA Clients
+# on-CPU RTC drivers
#
+CONFIG_RTC_DRV_BFIN=y
#
-# DMA Devices
+# DMA Engine support
#
+# CONFIG_DMA_ENGINE is not set
#
-# Auxiliary Display support
+# DMA Clients
#
#
-# Virtualization
+# DMA Devices
#
#
CONFIG_LOCKD_V4=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=m
+# CONFIG_SUNRPC_BIND34 is not set
# CONFIG_RPCSEC_GSS_KRB5 is not set
# CONFIG_RPCSEC_GSS_SPKM3 is not set
CONFIG_SMB_FS=m
CONFIG_ENABLE_MUST_CHECK=y
# CONFIG_MAGIC_SYSRQ is not set
# CONFIG_UNUSED_SYMBOLS is not set
-# CONFIG_DEBUG_FS is not set
+CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_KERNEL is not set
-CONFIG_LOG_BUF_SHIFT=14
# CONFIG_DEBUG_BUGVERBOSE is not set
-# CONFIG_DEBUG_SERIAL_EARLY_INIT is not set
+CONFIG_DEBUG_MMRS=y
CONFIG_DEBUG_HUNT_FOR_ZERO=y
+CONFIG_DEBUG_BFIN_HWTRACE_ON=y
+CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION_OFF=y
+# CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION_ONE is not set
+# CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION_TWO is not set
+CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION=0
+# CONFIG_DEBUG_BFIN_HWTRACE_EXPAND is not set
# CONFIG_DEBUG_BFIN_NO_KERN_HWTRACE is not set
+CONFIG_EARLY_PRINTK=y
CONFIG_CPLB_INFO=y
CONFIG_ACCESS_CHECK=y
CONFIG_BITREVERSE=y
CONFIG_CRC_CCITT=m
# CONFIG_CRC16 is not set
+# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
# CONFIG_LIBCRC32C is not set
CONFIG_ZLIB_INFLATE=y
CONFIG_PLIST=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.21.5
+# Linux kernel version: 2.6.22.6
#
# CONFIG_MMU is not set
# CONFIG_FPU is not set
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
# CONFIG_GENERIC_TIME is not set
-CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_GPIO=y
CONFIG_FORCE_MAX_ZONEORDER=14
+CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_IRQCHIP_DEMUX_GPIO=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
# CONFIG_TASKSTATS is not set
# CONFIG_UTS_NS is not set
# CONFIG_AUDIT is not set
-# CONFIG_IKCONFIG is not set
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
CONFIG_SYSFS_DEPRECATED=y
# CONFIG_RELAY is not set
CONFIG_BLK_DEV_INITRD=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
+CONFIG_VM_EVENT_COUNTERS=y
CONFIG_BIG_ORDER_ALLOC_NOFAIL_MAGIC=3
-CONFIG_BUDDY=y
# CONFIG_NP2 is not set
CONFIG_SLAB=y
-CONFIG_VM_EVENT_COUNTERS=y
+# CONFIG_SLUB is not set
+# CONFIG_SLOB is not set
CONFIG_RT_MUTEXES=y
CONFIG_TINY_SHMEM=y
CONFIG_BASE_SMALL=0
-# CONFIG_SLOB is not set
#
# Loadable module support
# BF537 Specific Configuration
#
-#
-# PORT F/G Selection
-#
-CONFIG_BF537_PORT_F=y
-# CONFIG_BF537_PORT_G is not set
-# CONFIG_BF537_PORT_H is not set
-
#
# Interrupt Priority Assignment
#
# CONFIG_CMDLINE_BOOL is not set
#
-# Board Setup
+# Clock/PLL Setup
#
CONFIG_CLKIN_HZ=25000000
-CONFIG_MEM_SIZE=64
-CONFIG_MEM_ADD_WIDTH=10
-CONFIG_BOOT_LOAD=0x1000
-
-#
-# Blackfin Kernel Optimizations
-#
+# CONFIG_BFIN_KERNEL_CLOCK is not set
+CONFIG_MAX_VCO_HZ=600000000
+CONFIG_MIN_VCO_HZ=50000000
+CONFIG_MAX_SCLK_HZ=133000000
+CONFIG_MIN_SCLK_HZ=27000000
#
-# Timer Tick
+# Kernel Timer/Scheduler
#
# CONFIG_HZ_100 is not set
CONFIG_HZ_250=y
# CONFIG_HZ_1000 is not set
CONFIG_HZ=250
+#
+# Memory Setup
+#
+CONFIG_MEM_SIZE=64
+CONFIG_MEM_ADD_WIDTH=10
+CONFIG_BOOT_LOAD=0x1000
+CONFIG_BFIN_SCRATCH_REG_RETN=y
+# CONFIG_BFIN_SCRATCH_REG_RETE is not set
+# CONFIG_BFIN_SCRATCH_REG_CYCLES is not set
+
+#
+# Blackfin Kernel Optimizations
+#
+
#
# Memory Optimizations
#
#
# Cache Support
#
-CONFIG_BLKFIN_CACHE=y
-CONFIG_BLKFIN_DCACHE=y
-# CONFIG_BLKFIN_DCACHE_BANKA is not set
-# CONFIG_BLKFIN_CACHE_LOCK is not set
-# CONFIG_BLKFIN_WB is not set
-CONFIG_BLKFIN_WT=y
+CONFIG_BFIN_ICACHE=y
+CONFIG_BFIN_DCACHE=y
+# CONFIG_BFIN_DCACHE_BANKA is not set
+# CONFIG_BFIN_ICACHE_LOCK is not set
+# CONFIG_BFIN_WB is not set
+CONFIG_BFIN_WT=y
CONFIG_L1_MAX_PIECE=16
-#
-# Clock Settings
-#
-# CONFIG_BFIN_KERNEL_CLOCK is not set
-
#
# Asynchonous Memory Configuration
#
# Bus options (PCI, PCMCIA, EISA, MCA, ISA)
#
# CONFIG_PCI is not set
+# CONFIG_ARCH_SUPPORTS_MSI is not set
#
# PCCARD (PCMCIA/CardBus) support
#
# CONFIG_PCCARD is not set
-#
-# PCI Hotplug Support
-#
-
#
# Executable file formats
#
#
# Networking options
#
-# CONFIG_NETDEBUG is not set
CONFIG_PACKET=y
# CONFIG_PACKET_MMAP is not set
CONFIG_UNIX=y
# CONFIG_NETLABEL is not set
# CONFIG_NETWORK_SECMARK is not set
# CONFIG_NETFILTER is not set
-
-#
-# DCCP Configuration (EXPERIMENTAL)
-#
# CONFIG_IP_DCCP is not set
-
-#
-# SCTP Configuration (EXPERIMENTAL)
-#
# CONFIG_IP_SCTP is not set
-
-#
-# TIPC Configuration (EXPERIMENTAL)
-#
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# FIR device drivers
#
# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_MAC80211 is not set
# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
#
# Device Drivers
# Connector - unified userspace <-> kernelspace linker
#
# CONFIG_CONNECTOR is not set
-
-#
-# Memory Technology Devices (MTD)
-#
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
# CONFIG_MTD_CONCAT is not set
CONFIG_MTD_RAM=y
CONFIG_MTD_ROM=m
# CONFIG_MTD_ABSENT is not set
-# CONFIG_MTD_OBSOLETE_CHIPS is not set
#
# Mapping drivers for chip access
# CONFIG_MTD_DOC2000 is not set
# CONFIG_MTD_DOC2001 is not set
# CONFIG_MTD_DOC2001PLUS is not set
-
-#
-# NAND Flash Device Drivers
-#
CONFIG_MTD_NAND=m
# CONFIG_MTD_NAND_VERIFY_WRITE is not set
# CONFIG_MTD_NAND_ECC_SMC is not set
+# CONFIG_MTD_NAND_MUSEUM_IDS is not set
CONFIG_MTD_NAND_BFIN=m
CONFIG_BFIN_NAND_BASE=0x20212000
CONFIG_BFIN_NAND_CLE=2
CONFIG_MTD_NAND_IDS=m
# CONFIG_MTD_NAND_DISKONCHIP is not set
# CONFIG_MTD_NAND_NANDSIM is not set
+# CONFIG_MTD_NAND_PLATFORM is not set
+# CONFIG_MTD_ONENAND is not set
#
-# OneNAND Flash Device Drivers
+# UBI - Unsorted block images
#
-# CONFIG_MTD_ONENAND is not set
+# CONFIG_MTD_UBI is not set
#
# Parallel port support
#
# Misc devices
#
-
-#
-# ATA/ATAPI/MFM/RLL support
-#
# CONFIG_IDE is not set
#
# CONFIG_RAID_ATTRS is not set
# CONFIG_SCSI is not set
# CONFIG_SCSI_NETLINK is not set
-
-#
-# Serial ATA (prod) and Parallel ATA (experimental) drivers
-#
# CONFIG_ATA is not set
#
#
# CONFIG_MD is not set
-#
-# Fusion MPT device support
-#
-# CONFIG_FUSION is not set
-
-#
-# IEEE 1394 (FireWire) support
-#
-
-#
-# I2O device support
-#
-
#
# Network device support
#
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
+CONFIG_PHYLIB=y
#
-# PHY device support
+# MII PHY device drivers
#
-# CONFIG_PHYLIB is not set
+# CONFIG_MARVELL_PHY is not set
+# CONFIG_DAVICOM_PHY is not set
+# CONFIG_QSEMI_PHY is not set
+# CONFIG_LXT_PHY is not set
+# CONFIG_CICADA_PHY is not set
+# CONFIG_VITESSE_PHY is not set
+CONFIG_SMSC_PHY=y
+# CONFIG_BROADCOM_PHY is not set
+# CONFIG_FIXED_PHY is not set
#
# Ethernet (10 or 100Mbit)
CONFIG_BFIN_RX_DESC_NUM=20
# CONFIG_BFIN_MAC_RMII is not set
# CONFIG_SMSC911X is not set
+# CONFIG_DM9000 is not set
+CONFIG_NETDEV_1000=y
+CONFIG_NETDEV_10000=y
#
-# Ethernet (1000 Mbit)
-#
-
-#
-# Ethernet (10000 Mbit)
-#
-
-#
-# Token Ring devices
-#
-
-#
-# Wireless LAN (non-hamradio)
-#
-# CONFIG_NET_RADIO is not set
-
-#
-# Wan interfaces
+# Wireless LAN
#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
# CONFIG_WAN is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
#
CONFIG_INPUT=y
# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
#
# Userland interfaces
# CONFIG_INPUT_KEYBOARD is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
CONFIG_INPUT_MISC=y
+# CONFIG_INPUT_ATI_REMOTE is not set
+# CONFIG_INPUT_ATI_REMOTE2 is not set
+# CONFIG_INPUT_KEYSPAN_REMOTE is not set
+# CONFIG_INPUT_POWERMATE is not set
+# CONFIG_INPUT_YEALINK is not set
# CONFIG_INPUT_UINPUT is not set
# CONFIG_BF53X_PFBUTTONS is not set
CONFIG_TWI_KEYPAD=m
#
# CONFIG_AD9960 is not set
# CONFIG_SPI_ADC_BF533 is not set
-# CONFIG_BF5xx_PFLAGS is not set
+# CONFIG_BFIN_PFLAGS is not set
# CONFIG_BF5xx_PPIFCD is not set
# CONFIG_BF5xx_TIMERS is not set
# CONFIG_BF5xx_PPI is not set
# IPMI
#
# CONFIG_IPMI_HANDLER is not set
-
-#
-# Watchdog Cards
-#
CONFIG_WATCHDOG=y
# CONFIG_WATCHDOG_NOWAYOUT is not set
CONFIG_HW_RANDOM=y
# CONFIG_GEN_RTC is not set
CONFIG_BLACKFIN_DPMC=y
-# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_RAW_DRIVER is not set
# TPM devices
#
# CONFIG_TCG_TPM is not set
-
-#
-# I2C support
-#
CONFIG_I2C=m
+CONFIG_I2C_BOARDINFO=y
CONFIG_I2C_CHARDEV=m
#
# CONFIG_I2C_BLACKFIN_GPIO is not set
CONFIG_I2C_BLACKFIN_TWI=m
CONFIG_I2C_BLACKFIN_TWI_CLK_KHZ=50
+# CONFIG_I2C_GPIO is not set
# CONFIG_I2C_OCORES is not set
# CONFIG_I2C_PARPORT_LIGHT is not set
+# CONFIG_I2C_SIMTEC is not set
# CONFIG_I2C_STUB is not set
-# CONFIG_I2C_PCA_ISA is not set
#
# Miscellaneous I2C Chip support
# SPI Protocol Masters
#
# CONFIG_SPI_AT25 is not set
+# CONFIG_SPI_SPIDEV is not set
#
# Dallas's 1-wire bus
#
# CONFIG_W1 is not set
-
-#
-# Hardware Monitoring support
-#
CONFIG_HWMON=y
# CONFIG_HWMON_VID is not set
# CONFIG_SENSORS_ABITUGURU is not set
+# CONFIG_SENSORS_AD7418 is not set
# CONFIG_SENSORS_ADM1021 is not set
# CONFIG_SENSORS_ADM1025 is not set
# CONFIG_SENSORS_ADM1026 is not set
# CONFIG_SENSORS_LM90 is not set
# CONFIG_SENSORS_LM92 is not set
# CONFIG_SENSORS_MAX1619 is not set
+# CONFIG_SENSORS_MAX6650 is not set
# CONFIG_SENSORS_PC87360 is not set
# CONFIG_SENSORS_PC87427 is not set
# CONFIG_SENSORS_SMSC47M1 is not set
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
-
-#
-# Digital Video Broadcasting Devices
-#
-# CONFIG_DVB is not set
+# CONFIG_DVB_CORE is not set
+CONFIG_DAB=y
#
# Graphics support
CONFIG_BACKLIGHT_LCD_SUPPORT=y
CONFIG_BACKLIGHT_CLASS_DEVICE=m
CONFIG_LCD_CLASS_DEVICE=m
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
+# CONFIG_VGASTATE is not set
CONFIG_FB=m
CONFIG_FIRMWARE_EDID=y
# CONFIG_FB_DDC is not set
CONFIG_FB_CFB_FILLRECT=m
CONFIG_FB_CFB_COPYAREA=m
CONFIG_FB_CFB_IMAGEBLIT=m
+# CONFIG_FB_SYS_FILLRECT is not set
+# CONFIG_FB_SYS_COPYAREA is not set
+# CONFIG_FB_SYS_IMAGEBLIT is not set
+# CONFIG_FB_SYS_FOPS is not set
+CONFIG_FB_DEFERRED_IO=y
# CONFIG_FB_SVGALIB is not set
# CONFIG_FB_MACMODES is not set
# CONFIG_FB_BACKLIGHT is not set
# CONFIG_FB_BFIN_BGR is not set
# CONFIG_FB_S1D13XXX is not set
# CONFIG_FB_VIRTUAL is not set
-
-#
-# Logo configuration
-#
# CONFIG_LOGO is not set
#
# CONFIG_SND_BLACKFIN_AD1836_I2S is not set
CONFIG_SND_BLACKFIN_AD1836_MULSUB=y
# CONFIG_SND_BLACKFIN_AD1836_5P1 is not set
-CONFIG_SND_BLACKFIN_AD1981B=m
CONFIG_SND_BLACKFIN_SPORT=0
CONFIG_SND_BLACKFIN_SPI_PFBIT=4
CONFIG_SND_BFIN_AD73311=m
CONFIG_SND_BFIN_AD73311_SE=4
#
-# SoC audio support
+# System on Chip audio support
#
# CONFIG_SND_SOC is not set
+#
+# SoC Audio for the ADI Blackfin
+#
+# CONFIG_SND_BF5XX_HAVE_COLD_RESET is not set
+
#
# Open Sound System
#
# CONFIG_USB is not set
#
-# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
+# Enable Host or Gadget support to see Inventra options
#
#
-# USB Gadget Support
+# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
#
-# CONFIG_USB_GADGET is not set
#
-# MMC/SD Card support
+# USB Gadget Support
#
-# CONFIG_SPI_MMC is not set
+# CONFIG_USB_GADGET is not set
# CONFIG_MMC is not set
#
CONFIG_RTC_INTF_PROC=y
CONFIG_RTC_INTF_DEV=y
# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set
+# CONFIG_RTC_DRV_TEST is not set
#
-# RTC drivers
+# I2C RTC drivers
#
-# CONFIG_RTC_DRV_X1205 is not set
# CONFIG_RTC_DRV_DS1307 is not set
-# CONFIG_RTC_DRV_DS1553 is not set
-# CONFIG_RTC_DRV_ISL1208 is not set
# CONFIG_RTC_DRV_DS1672 is not set
-# CONFIG_RTC_DRV_DS1742 is not set
+# CONFIG_RTC_DRV_MAX6900 is not set
+# CONFIG_RTC_DRV_RS5C372 is not set
+# CONFIG_RTC_DRV_ISL1208 is not set
+# CONFIG_RTC_DRV_X1205 is not set
# CONFIG_RTC_DRV_PCF8563 is not set
+# CONFIG_RTC_DRV_PCF8583 is not set
+
+#
+# SPI RTC drivers
+#
# CONFIG_RTC_DRV_RS5C348 is not set
-# CONFIG_RTC_DRV_RS5C372 is not set
-# CONFIG_RTC_DRV_M48T86 is not set
-# CONFIG_RTC_DRV_TEST is not set
# CONFIG_RTC_DRV_MAX6902 is not set
-# CONFIG_RTC_DRV_V3020 is not set
-CONFIG_RTC_DRV_BFIN=y
#
-# DMA Engine support
+# Platform RTC drivers
#
-# CONFIG_DMA_ENGINE is not set
+# CONFIG_RTC_DRV_DS1553 is not set
+# CONFIG_RTC_DRV_DS1742 is not set
+# CONFIG_RTC_DRV_M48T86 is not set
+# CONFIG_RTC_DRV_V3020 is not set
#
-# DMA Clients
+# on-CPU RTC drivers
#
+CONFIG_RTC_DRV_BFIN=y
#
-# DMA Devices
+# DMA Engine support
#
+# CONFIG_DMA_ENGINE is not set
#
-# Auxiliary Display support
+# DMA Clients
#
#
-# Virtualization
+# DMA Devices
#
#
CONFIG_LOCKD_V4=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=m
+# CONFIG_SUNRPC_BIND34 is not set
# CONFIG_RPCSEC_GSS_KRB5 is not set
# CONFIG_RPCSEC_GSS_SPKM3 is not set
CONFIG_SMB_FS=m
CONFIG_ENABLE_MUST_CHECK=y
# CONFIG_MAGIC_SYSRQ is not set
# CONFIG_UNUSED_SYMBOLS is not set
-# CONFIG_DEBUG_FS is not set
+CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_KERNEL is not set
-CONFIG_LOG_BUF_SHIFT=14
# CONFIG_DEBUG_BUGVERBOSE is not set
-# CONFIG_DEBUG_SERIAL_EARLY_INIT is not set
+CONFIG_DEBUG_MMRS=y
CONFIG_DEBUG_HUNT_FOR_ZERO=y
+CONFIG_DEBUG_BFIN_HWTRACE_ON=y
+CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION_OFF=y
+# CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION_ONE is not set
+# CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION_TWO is not set
+CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION=0
+# CONFIG_DEBUG_BFIN_HWTRACE_EXPAND is not set
# CONFIG_DEBUG_BFIN_NO_KERN_HWTRACE is not set
+CONFIG_EARLY_PRINTK=y
CONFIG_CPLB_INFO=y
CONFIG_ACCESS_CHECK=y
CONFIG_BITREVERSE=y
CONFIG_CRC_CCITT=m
# CONFIG_CRC16 is not set
+# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
# CONFIG_LIBCRC32C is not set
CONFIG_ZLIB_INFLATE=y
CONFIG_PLIST=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.21.5
+# Linux kernel version: 2.6.22.6
#
# CONFIG_MMU is not set
# CONFIG_FPU is not set
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
# CONFIG_GENERIC_TIME is not set
-CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_GPIO=y
CONFIG_FORCE_MAX_ZONEORDER=14
+CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_IRQCHIP_DEMUX_GPIO=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
# CONFIG_TASKSTATS is not set
# CONFIG_UTS_NS is not set
# CONFIG_AUDIT is not set
-# CONFIG_IKCONFIG is not set
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
CONFIG_SYSFS_DEPRECATED=y
# CONFIG_RELAY is not set
CONFIG_BLK_DEV_INITRD=y
CONFIG_UID16=y
CONFIG_SYSCTL_SYSCALL=y
CONFIG_KALLSYMS=y
-# CONFIG_KALLSYMS_ALL is not set
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
+CONFIG_VM_EVENT_COUNTERS=y
CONFIG_BIG_ORDER_ALLOC_NOFAIL_MAGIC=3
# CONFIG_NP2 is not set
CONFIG_SLAB=y
-CONFIG_VM_EVENT_COUNTERS=y
+# CONFIG_SLUB is not set
+# CONFIG_SLOB is not set
CONFIG_RT_MUTEXES=y
CONFIG_TINY_SHMEM=y
CONFIG_BASE_SMALL=0
-# CONFIG_SLOB is not set
#
# Loadable module support
#
# BF548 Specific Configuration
#
+# CONFIG_DEB_DMA_URGENT is not set
#
# Interrupt Priority Assignment
CONFIG_IRQ_PINT3=11
#
-# Board customizations
+# Pin Interrupt to Port Assignment
#
-# CONFIG_CMDLINE_BOOL is not set
#
-# Board Setup
+# Assignment
#
-CONFIG_CLKIN_HZ=25000000
-CONFIG_MEM_SIZE=64
-CONFIG_MEM_ADD_WIDTH=10
-CONFIG_BOOT_LOAD=0x1000
+CONFIG_PINTx_REASSIGN=y
+CONFIG_PINT0_ASSIGN=0x00000101
+CONFIG_PINT1_ASSIGN=0x01010000
+CONFIG_PINT2_ASSIGN=0x07000101
+CONFIG_PINT3_ASSIGN=0x02020303
#
-# Blackfin Kernel Optimizations
+# Board customizations
#
+# CONFIG_CMDLINE_BOOL is not set
#
-# Timer Tick
+# Clock/PLL Setup
+#
+CONFIG_CLKIN_HZ=25000000
+# CONFIG_BFIN_KERNEL_CLOCK is not set
+CONFIG_MAX_VCO_HZ=533000000
+CONFIG_MIN_VCO_HZ=50000000
+CONFIG_MAX_SCLK_HZ=133000000
+CONFIG_MIN_SCLK_HZ=27000000
+
+#
+# Kernel Timer/Scheduler
#
# CONFIG_HZ_100 is not set
CONFIG_HZ_250=y
# CONFIG_HZ_1000 is not set
CONFIG_HZ=250
+#
+# Memory Setup
+#
+CONFIG_MEM_SIZE=64
+CONFIG_MEM_ADD_WIDTH=10
+CONFIG_BOOT_LOAD=0x1000
+CONFIG_BFIN_SCRATCH_REG_RETN=y
+# CONFIG_BFIN_SCRATCH_REG_RETE is not set
+# CONFIG_BFIN_SCRATCH_REG_CYCLES is not set
+
+#
+# Blackfin Kernel Optimizations
+#
+
#
# Memory Optimizations
#
CONFIG_DO_IRQ_L1=y
CONFIG_CORE_TIMER_IRQ_L1=y
CONFIG_IDLE_L1=y
-CONFIG_SCHEDULE_L1=y
+# CONFIG_SCHEDULE_L1 is not set
CONFIG_ARITHMETIC_OPS_L1=y
CONFIG_ACCESS_OK_L1=y
-CONFIG_MEMSET_L1=y
-CONFIG_MEMCPY_L1=y
-CONFIG_SYS_BFIN_SPINLOCK_L1=y
+# CONFIG_MEMSET_L1 is not set
+# CONFIG_MEMCPY_L1 is not set
+# CONFIG_SYS_BFIN_SPINLOCK_L1 is not set
# CONFIG_IP_CHECKSUM_L1 is not set
CONFIG_CACHELINE_ALIGNED_L1=y
# CONFIG_SYSCALL_TAB_L1 is not set
#
# Cache Support
#
-CONFIG_BLKFIN_CACHE=y
-CONFIG_BLKFIN_DCACHE=y
-# CONFIG_BLKFIN_DCACHE_BANKA is not set
-# CONFIG_BLKFIN_CACHE_LOCK is not set
-# CONFIG_BLKFIN_WB is not set
-CONFIG_BLKFIN_WT=y
+CONFIG_BFIN_ICACHE=y
+CONFIG_BFIN_DCACHE=y
+# CONFIG_BFIN_DCACHE_BANKA is not set
+# CONFIG_BFIN_ICACHE_LOCK is not set
+# CONFIG_BFIN_WB is not set
+CONFIG_BFIN_WT=y
CONFIG_L1_MAX_PIECE=16
-#
-# Clock Settings
-#
-# CONFIG_BFIN_KERNEL_CLOCK is not set
-
#
# Asynchonous Memory Configuration
#
# EBIU_AMBCTL Global Control
#
CONFIG_C_AMCKEN=y
-CONFIG_C_CDPRIO=y
# CONFIG_C_AMBEN is not set
# CONFIG_C_AMBEN_B0 is not set
# CONFIG_C_AMBEN_B0_B1 is not set
# EBIU_AMBCTL Control
#
CONFIG_BANK_0=0x7BB0
-CONFIG_BANK_1=0x7BB0
+CONFIG_BANK_1=0x5554
CONFIG_BANK_2=0x7BB0
CONFIG_BANK_3=0x99B3
# Bus options (PCI, PCMCIA, EISA, MCA, ISA)
#
# CONFIG_PCI is not set
+# CONFIG_ARCH_SUPPORTS_MSI is not set
#
# PCCARD (PCMCIA/CardBus) support
#
# CONFIG_PCCARD is not set
-#
-# PCI Hotplug Support
-#
-
#
# Executable file formats
#
#
# Networking options
#
-# CONFIG_NETDEBUG is not set
CONFIG_PACKET=y
# CONFIG_PACKET_MMAP is not set
CONFIG_UNIX=y
# CONFIG_NETLABEL is not set
# CONFIG_NETWORK_SECMARK is not set
# CONFIG_NETFILTER is not set
-
-#
-# DCCP Configuration (EXPERIMENTAL)
-#
# CONFIG_IP_DCCP is not set
-
-#
-# SCTP Configuration (EXPERIMENTAL)
-#
# CONFIG_IP_SCTP is not set
-
-#
-# TIPC Configuration (EXPERIMENTAL)
-#
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_HAMRADIO is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_MAC80211 is not set
# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
#
# Device Drivers
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
# CONFIG_FW_LOADER is not set
-# CONFIG_DEBUG_DRIVER is not set
-# CONFIG_DEBUG_DEVRES is not set
# CONFIG_SYS_HYPERVISOR is not set
#
# Connector - unified userspace <-> kernelspace linker
#
# CONFIG_CONNECTOR is not set
-
-#
-# Memory Technology Devices (MTD)
-#
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
# CONFIG_MTD_CONCAT is not set
CONFIG_MTD_PARTITIONS=y
# CONFIG_MTD_REDBOOT_PARTS is not set
-# CONFIG_MTD_CMDLINE_PARTS is not set
+CONFIG_MTD_CMDLINE_PARTS=y
#
# User Modules And Translation Layers
#
-# CONFIG_MTD_CHAR is not set
+CONFIG_MTD_CHAR=y
CONFIG_MTD_BLKDEVS=y
CONFIG_MTD_BLOCK=y
# CONFIG_FTL is not set
#
# RAM/ROM/Flash chip drivers
#
-# CONFIG_MTD_CFI is not set
+CONFIG_MTD_CFI=y
# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_GEN_PROBE=y
+# CONFIG_MTD_CFI_ADV_OPTIONS is not set
CONFIG_MTD_MAP_BANK_WIDTH_1=y
CONFIG_MTD_MAP_BANK_WIDTH_2=y
CONFIG_MTD_MAP_BANK_WIDTH_4=y
CONFIG_MTD_CFI_I2=y
# CONFIG_MTD_CFI_I4 is not set
# CONFIG_MTD_CFI_I8 is not set
+CONFIG_MTD_CFI_INTELEXT=y
+# CONFIG_MTD_CFI_AMDSTD is not set
+# CONFIG_MTD_CFI_STAA is not set
+# CONFIG_MTD_MW320D is not set
+CONFIG_MTD_CFI_UTIL=y
CONFIG_MTD_RAM=y
# CONFIG_MTD_ROM is not set
# CONFIG_MTD_ABSENT is not set
-# CONFIG_MTD_OBSOLETE_CHIPS is not set
#
# Mapping drivers for chip access
#
CONFIG_MTD_COMPLEX_MAPPINGS=y
+CONFIG_MTD_PHYSMAP=y
+CONFIG_MTD_PHYSMAP_START=0x20000000
+CONFIG_MTD_PHYSMAP_LEN=0x400000
+CONFIG_MTD_PHYSMAP_BANKWIDTH=2
# CONFIG_MTD_BF5xx is not set
-CONFIG_MTD_UCLINUX=y
+# CONFIG_MTD_UCLINUX is not set
# CONFIG_MTD_PLATRAM is not set
#
# Self-contained MTD device drivers
#
+# CONFIG_MTD_DATAFLASH is not set
+# CONFIG_MTD_M25P80 is not set
# CONFIG_MTD_SLRAM is not set
# CONFIG_MTD_PHRAM is not set
# CONFIG_MTD_MTDRAM is not set
# CONFIG_MTD_DOC2000 is not set
# CONFIG_MTD_DOC2001 is not set
# CONFIG_MTD_DOC2001PLUS is not set
+CONFIG_MTD_NAND=y
+# CONFIG_MTD_NAND_VERIFY_WRITE is not set
+# CONFIG_MTD_NAND_ECC_SMC is not set
+# CONFIG_MTD_NAND_MUSEUM_IDS is not set
+# CONFIG_MTD_NAND_BFIN is not set
+CONFIG_MTD_NAND_IDS=y
+CONFIG_MTD_NAND_BF5XX=y
+CONFIG_MTD_NAND_BF5XX_HWECC=y
+# CONFIG_MTD_NAND_DISKONCHIP is not set
+# CONFIG_MTD_NAND_NANDSIM is not set
+# CONFIG_MTD_NAND_PLATFORM is not set
+# CONFIG_MTD_ONENAND is not set
#
-# NAND Flash Device Drivers
-#
-# CONFIG_MTD_NAND is not set
-
-#
-# OneNAND Flash Device Drivers
+# UBI - Unsorted block images
#
-# CONFIG_MTD_ONENAND is not set
+# CONFIG_MTD_UBI is not set
#
# Parallel port support
#
# Misc devices
#
-
-#
-# ATA/ATAPI/MFM/RLL support
-#
# CONFIG_IDE is not set
#
# SCSI device support
#
# CONFIG_RAID_ATTRS is not set
-# CONFIG_SCSI is not set
+CONFIG_SCSI=y
+# CONFIG_SCSI_TGT is not set
# CONFIG_SCSI_NETLINK is not set
+CONFIG_SCSI_PROC_FS=y
#
-# Serial ATA (prod) and Parallel ATA (experimental) drivers
+# SCSI support type (disk, tape, CD-ROM)
#
-# CONFIG_ATA is not set
+CONFIG_BLK_DEV_SD=y
+# CONFIG_CHR_DEV_ST is not set
+# CONFIG_CHR_DEV_OSST is not set
+CONFIG_BLK_DEV_SR=y
+# CONFIG_BLK_DEV_SR_VENDOR is not set
+# CONFIG_CHR_DEV_SG is not set
+# CONFIG_CHR_DEV_SCH is not set
#
-# Multi-device support (RAID and LVM)
+# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
-# CONFIG_MD is not set
+# CONFIG_SCSI_MULTI_LUN is not set
+# CONFIG_SCSI_CONSTANTS is not set
+# CONFIG_SCSI_LOGGING is not set
+# CONFIG_SCSI_SCAN_ASYNC is not set
+CONFIG_SCSI_WAIT_SCAN=m
#
-# Fusion MPT device support
+# SCSI Transports
#
-# CONFIG_FUSION is not set
+# CONFIG_SCSI_SPI_ATTRS is not set
+# CONFIG_SCSI_FC_ATTRS is not set
+# CONFIG_SCSI_ISCSI_ATTRS is not set
+# CONFIG_SCSI_SAS_ATTRS is not set
+# CONFIG_SCSI_SAS_LIBSAS is not set
#
-# IEEE 1394 (FireWire) support
+# SCSI low-level drivers
#
+# CONFIG_ISCSI_TCP is not set
+# CONFIG_SCSI_DEBUG is not set
+CONFIG_ATA=y
+# CONFIG_ATA_NONSTANDARD is not set
+# CONFIG_PATA_PLATFORM is not set
+CONFIG_PATA_BF54X=y
+CONFIG_PATA_BF54X_DMA=y
#
-# I2O device support
+# Multi-device support (RAID and LVM)
#
+# CONFIG_MD is not set
#
# Network device support
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
-
-#
-# PHY device support
-#
# CONFIG_PHYLIB is not set
#
CONFIG_NET_ETHERNET=y
CONFIG_MII=y
# CONFIG_SMC91X is not set
-# CONFIG_SMSC911X is not set
-
-#
-# Ethernet (1000 Mbit)
-#
-
-#
-# Ethernet (10000 Mbit)
-#
+CONFIG_SMSC911X=y
+# CONFIG_DM9000 is not set
+CONFIG_NETDEV_1000=y
+CONFIG_NETDEV_10000=y
#
-# Token Ring devices
-#
-
-#
-# Wireless LAN (non-hamradio)
-#
-# CONFIG_NET_RADIO is not set
-
-#
-# Wan interfaces
+# Wireless LAN
#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
# CONFIG_WAN is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
#
CONFIG_INPUT=y
# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
#
# Userland interfaces
# CONFIG_INPUT_KEYBOARD is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
CONFIG_INPUT_MISC=y
+# CONFIG_INPUT_ATI_REMOTE is not set
+# CONFIG_INPUT_ATI_REMOTE2 is not set
+# CONFIG_INPUT_KEYSPAN_REMOTE is not set
+# CONFIG_INPUT_POWERMATE is not set
+# CONFIG_INPUT_YEALINK is not set
# CONFIG_INPUT_UINPUT is not set
# CONFIG_BF53X_PFBUTTONS is not set
+# CONFIG_TWI_KEYPAD is not set
#
# Hardware I/O ports
#
# CONFIG_AD9960 is not set
# CONFIG_SPI_ADC_BF533 is not set
-# CONFIG_BF5xx_PFLAGS is not set
+# CONFIG_BFIN_PFLAGS is not set
# CONFIG_BF5xx_PPIFCD is not set
# CONFIG_BF5xx_TIMERS is not set
# CONFIG_BF5xx_PPI is not set
# CONFIG_BFIN_SPORT is not set
# CONFIG_BFIN_TIMER_LATENCY is not set
+# CONFIG_TWI_LCD is not set
+# CONFIG_AD5304 is not set
+# CONFIG_BF5xx_TEA5764 is not set
# CONFIG_BF5xx_FBDMA is not set
# CONFIG_VT is not set
# CONFIG_SERIAL_NONSTANDARD is not set
# IPMI
#
# CONFIG_IPMI_HANDLER is not set
-
-#
-# Watchdog Cards
-#
# CONFIG_WATCHDOG is not set
CONFIG_HW_RANDOM=y
# CONFIG_GEN_RTC is not set
-# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_RAW_DRIVER is not set
# TPM devices
#
# CONFIG_TCG_TPM is not set
+CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_CHARDEV=y
+
+#
+# I2C Algorithms
+#
+# CONFIG_I2C_ALGOBIT is not set
+# CONFIG_I2C_ALGOPCF is not set
+# CONFIG_I2C_ALGOPCA is not set
#
-# I2C support
+# I2C Hardware Bus support
#
-# CONFIG_I2C is not set
+# CONFIG_I2C_BLACKFIN_GPIO is not set
+CONFIG_I2C_BLACKFIN_TWI=y
+CONFIG_I2C_BLACKFIN_TWI_CLK_KHZ=50
+# CONFIG_I2C_GPIO is not set
+# CONFIG_I2C_OCORES is not set
+# CONFIG_I2C_PARPORT_LIGHT is not set
+# CONFIG_I2C_SIMTEC is not set
+# CONFIG_I2C_STUB is not set
+
+#
+# Miscellaneous I2C Chip support
+#
+# CONFIG_SENSORS_DS1337 is not set
+# CONFIG_SENSORS_DS1374 is not set
+# CONFIG_SENSORS_AD5252 is not set
+# CONFIG_SENSORS_EEPROM is not set
+# CONFIG_SENSORS_PCF8574 is not set
+# CONFIG_SENSORS_PCF8575 is not set
+# CONFIG_SENSORS_PCA9543 is not set
+# CONFIG_SENSORS_PCA9539 is not set
+# CONFIG_SENSORS_PCF8591 is not set
+# CONFIG_SENSORS_MAX6875 is not set
+# CONFIG_I2C_DEBUG_CORE is not set
+# CONFIG_I2C_DEBUG_ALGO is not set
+# CONFIG_I2C_DEBUG_BUS is not set
+# CONFIG_I2C_DEBUG_CHIP is not set
#
# SPI support
#
-# CONFIG_SPI is not set
-# CONFIG_SPI_MASTER is not set
+CONFIG_SPI=y
+CONFIG_SPI_MASTER=y
#
-# Dallas's 1-wire bus
+# SPI Master Controller Drivers
#
-# CONFIG_W1 is not set
+CONFIG_SPI_BFIN=y
+# CONFIG_SPI_BITBANG is not set
+
+#
+# SPI Protocol Masters
+#
+# CONFIG_SPI_AT25 is not set
+# CONFIG_SPI_SPIDEV is not set
#
-# Hardware Monitoring support
+# Dallas's 1-wire bus
#
+# CONFIG_W1 is not set
CONFIG_HWMON=y
# CONFIG_HWMON_VID is not set
# CONFIG_SENSORS_ABITUGURU is not set
+# CONFIG_SENSORS_AD7418 is not set
+# CONFIG_SENSORS_ADM1021 is not set
+# CONFIG_SENSORS_ADM1025 is not set
+# CONFIG_SENSORS_ADM1026 is not set
+# CONFIG_SENSORS_ADM1029 is not set
+# CONFIG_SENSORS_ADM1031 is not set
+# CONFIG_SENSORS_ADM9240 is not set
+# CONFIG_SENSORS_ASB100 is not set
+# CONFIG_SENSORS_ATXP1 is not set
+# CONFIG_SENSORS_DS1621 is not set
# CONFIG_SENSORS_F71805F is not set
+# CONFIG_SENSORS_FSCHER is not set
+# CONFIG_SENSORS_FSCPOS is not set
+# CONFIG_SENSORS_GL518SM is not set
+# CONFIG_SENSORS_GL520SM is not set
+# CONFIG_SENSORS_IT87 is not set
+# CONFIG_SENSORS_LM63 is not set
+# CONFIG_SENSORS_LM70 is not set
+# CONFIG_SENSORS_LM75 is not set
+# CONFIG_SENSORS_LM77 is not set
+# CONFIG_SENSORS_LM78 is not set
+# CONFIG_SENSORS_LM80 is not set
+# CONFIG_SENSORS_LM83 is not set
+# CONFIG_SENSORS_LM85 is not set
+# CONFIG_SENSORS_LM87 is not set
+# CONFIG_SENSORS_LM90 is not set
+# CONFIG_SENSORS_LM92 is not set
+# CONFIG_SENSORS_MAX1619 is not set
+# CONFIG_SENSORS_MAX6650 is not set
+# CONFIG_SENSORS_PC87360 is not set
# CONFIG_SENSORS_PC87427 is not set
+# CONFIG_SENSORS_SMSC47M1 is not set
+# CONFIG_SENSORS_SMSC47M192 is not set
+# CONFIG_SENSORS_SMSC47B397 is not set
# CONFIG_SENSORS_VT1211 is not set
+# CONFIG_SENSORS_W83781D is not set
+# CONFIG_SENSORS_W83791D is not set
+# CONFIG_SENSORS_W83792D is not set
+# CONFIG_SENSORS_W83793 is not set
+# CONFIG_SENSORS_W83L785TS is not set
+# CONFIG_SENSORS_W83627HF is not set
+# CONFIG_SENSORS_W83627EHF is not set
# CONFIG_HWMON_DEBUG_CHIP is not set
#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+CONFIG_DAB=y
#
-# Digital Video Broadcasting Devices
+# Graphics support
#
-# CONFIG_DVB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
-# Graphics support
+# Display device support
#
-# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+# CONFIG_DISPLAY_SUPPORT is not set
+# CONFIG_VGASTATE is not set
# CONFIG_FB is not set
#
# CONFIG_USB_ARCH_HAS_EHCI is not set
# CONFIG_USB is not set
+#
+# Enable Host or Gadget support to see Inventra options
+#
+
#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set
+CONFIG_MMC=m
+# CONFIG_MMC_DEBUG is not set
+# CONFIG_MMC_UNSAFE_RESUME is not set
+
+#
+# MMC/SD Card Drivers
+#
+CONFIG_MMC_BLOCK=m
#
-# MMC/SD Card support
+# MMC/SD Host Controller Drivers
#
-# CONFIG_MMC is not set
+CONFIG_SDH_BFIN=m
+# CONFIG_SPI_MMC is not set
#
# LED devices
CONFIG_RTC_INTF_PROC=y
CONFIG_RTC_INTF_DEV=y
# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set
+# CONFIG_RTC_DRV_TEST is not set
#
-# RTC drivers
+# I2C RTC drivers
+#
+# CONFIG_RTC_DRV_DS1307 is not set
+# CONFIG_RTC_DRV_DS1672 is not set
+# CONFIG_RTC_DRV_MAX6900 is not set
+# CONFIG_RTC_DRV_RS5C372 is not set
+# CONFIG_RTC_DRV_ISL1208 is not set
+# CONFIG_RTC_DRV_X1205 is not set
+# CONFIG_RTC_DRV_PCF8563 is not set
+# CONFIG_RTC_DRV_PCF8583 is not set
+
+#
+# SPI RTC drivers
+#
+# CONFIG_RTC_DRV_RS5C348 is not set
+# CONFIG_RTC_DRV_MAX6902 is not set
+
+#
+# Platform RTC drivers
#
# CONFIG_RTC_DRV_DS1553 is not set
# CONFIG_RTC_DRV_DS1742 is not set
# CONFIG_RTC_DRV_M48T86 is not set
-# CONFIG_RTC_DRV_TEST is not set
# CONFIG_RTC_DRV_V3020 is not set
+
+#
+# on-CPU RTC drivers
+#
CONFIG_RTC_DRV_BFIN=y
#
# DMA Devices
#
-#
-# Auxiliary Display support
-#
-
-#
-# Virtualization
-#
-
#
# PBX support
#
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
-# CONFIG_YAFFS_FS is not set
-# CONFIG_JFFS2_FS is not set
+CONFIG_YAFFS_FS=m
+CONFIG_YAFFS_YAFFS1=y
+# CONFIG_YAFFS_DOES_ECC is not set
+CONFIG_YAFFS_YAFFS2=y
+CONFIG_YAFFS_AUTO_YAFFS2=y
+# CONFIG_YAFFS_DISABLE_LAZY_LOAD is not set
+CONFIG_YAFFS_CHECKPOINT_RESERVED_BLOCKS=10
+# CONFIG_YAFFS_DISABLE_WIDE_TNODES is not set
+# CONFIG_YAFFS_ALWAYS_CHECK_CHUNK_ERASED is not set
+CONFIG_YAFFS_SHORT_NAMES_IN_RAM=y
+CONFIG_JFFS2_FS=m
+CONFIG_JFFS2_FS_DEBUG=0
+CONFIG_JFFS2_FS_WRITEBUFFER=y
+# CONFIG_JFFS2_SUMMARY is not set
+# CONFIG_JFFS2_FS_XATTR is not set
+# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
+CONFIG_JFFS2_ZLIB=y
+CONFIG_JFFS2_RTIME=y
+# CONFIG_JFFS2_RUBIN is not set
# CONFIG_CRAMFS is not set
# CONFIG_VXFS_FS is not set
# CONFIG_HPFS_FS is not set
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_MAGIC_SYSRQ=y
# CONFIG_UNUSED_SYMBOLS is not set
-# CONFIG_DEBUG_FS is not set
+CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
-CONFIG_DEBUG_KERNEL=y
-# CONFIG_DEBUG_SHIRQ is not set
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_DETECT_SOFTLOCKUP=y
-# CONFIG_SCHEDSTATS is not set
-# CONFIG_TIMER_STATS is not set
-# CONFIG_DEBUG_SLAB is not set
-# CONFIG_DEBUG_RT_MUTEXES is not set
-# CONFIG_RT_MUTEX_TESTER is not set
-# CONFIG_DEBUG_SPINLOCK is not set
-# CONFIG_DEBUG_MUTEXES is not set
-# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
-# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
-# CONFIG_DEBUG_KOBJECT is not set
+# CONFIG_DEBUG_KERNEL is not set
# CONFIG_DEBUG_BUGVERBOSE is not set
-CONFIG_DEBUG_INFO=y
-# CONFIG_DEBUG_VM is not set
-# CONFIG_DEBUG_LIST is not set
-CONFIG_FRAME_POINTER=y
-CONFIG_FORCED_INLINING=y
-# CONFIG_RCU_TORTURE_TEST is not set
-# CONFIG_FAULT_INJECTION is not set
-CONFIG_DEBUG_HWERR=y
-# CONFIG_DEBUG_ICACHE_CHECK is not set
-# CONFIG_DEBUG_KERNEL_START is not set
-# CONFIG_DEBUG_SERIAL_EARLY_INIT is not set
+CONFIG_DEBUG_MMRS=y
CONFIG_DEBUG_HUNT_FOR_ZERO=y
+CONFIG_DEBUG_BFIN_HWTRACE_ON=y
+CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION_OFF=y
+# CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION_ONE is not set
+# CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION_TWO is not set
+CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION=0
+# CONFIG_DEBUG_BFIN_HWTRACE_EXPAND is not set
# CONFIG_DEBUG_BFIN_NO_KERN_HWTRACE is not set
+CONFIG_EARLY_PRINTK=y
CONFIG_CPLB_INFO=y
CONFIG_ACCESS_CHECK=y
CONFIG_BITREVERSE=y
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
+# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
# CONFIG_LIBCRC32C is not set
CONFIG_ZLIB_INFLATE=y
+CONFIG_ZLIB_DEFLATE=m
CONFIG_PLIST=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.21.5
+# Linux kernel version: 2.6.22.6
#
# CONFIG_MMU is not set
# CONFIG_FPU is not set
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
# CONFIG_GENERIC_TIME is not set
-CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_GPIO=y
CONFIG_FORCE_MAX_ZONEORDER=14
+CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_IRQCHIP_DEMUX_GPIO=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
# CONFIG_TASKSTATS is not set
# CONFIG_UTS_NS is not set
# CONFIG_AUDIT is not set
-# CONFIG_IKCONFIG is not set
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
CONFIG_SYSFS_DEPRECATED=y
# CONFIG_RELAY is not set
CONFIG_BLK_DEV_INITRD=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
+CONFIG_VM_EVENT_COUNTERS=y
CONFIG_BIG_ORDER_ALLOC_NOFAIL_MAGIC=3
-CONFIG_BUDDY=y
# CONFIG_NP2 is not set
CONFIG_SLAB=y
-CONFIG_VM_EVENT_COUNTERS=y
+# CONFIG_SLUB is not set
+# CONFIG_SLOB is not set
CONFIG_RT_MUTEXES=y
CONFIG_TINY_SHMEM=y
CONFIG_BASE_SMALL=0
-# CONFIG_SLOB is not set
#
# Loadable module support
# CONFIG_CMDLINE_BOOL is not set
#
-# Board Setup
+# Clock/PLL Setup
#
CONFIG_CLKIN_HZ=30000000
-CONFIG_MEM_SIZE=64
-CONFIG_MEM_ADD_WIDTH=9
-CONFIG_BOOT_LOAD=0x1000
-
-#
-# Blackfin Kernel Optimizations
-#
+# CONFIG_BFIN_KERNEL_CLOCK is not set
+CONFIG_MAX_VCO_HZ=600000000
+CONFIG_MIN_VCO_HZ=50000000
+CONFIG_MAX_SCLK_HZ=133000000
+CONFIG_MIN_SCLK_HZ=27000000
#
-# Timer Tick
+# Kernel Timer/Scheduler
#
# CONFIG_HZ_100 is not set
CONFIG_HZ_250=y
# CONFIG_HZ_1000 is not set
CONFIG_HZ=250
+#
+# Memory Setup
+#
+CONFIG_MEM_SIZE=64
+CONFIG_MEM_ADD_WIDTH=9
+CONFIG_BOOT_LOAD=0x1000
+CONFIG_BFIN_SCRATCH_REG_RETN=y
+# CONFIG_BFIN_SCRATCH_REG_RETE is not set
+# CONFIG_BFIN_SCRATCH_REG_CYCLES is not set
+
+#
+# Blackfin Kernel Optimizations
+#
+
#
# Memory Optimizations
#
#
# Cache Support
#
-CONFIG_BLKFIN_CACHE=y
-CONFIG_BLKFIN_DCACHE=y
-# CONFIG_BLKFIN_DCACHE_BANKA is not set
-# CONFIG_BLKFIN_CACHE_LOCK is not set
-# CONFIG_BLKFIN_WB is not set
-CONFIG_BLKFIN_WT=y
+CONFIG_BFIN_ICACHE=y
+CONFIG_BFIN_DCACHE=y
+# CONFIG_BFIN_DCACHE_BANKA is not set
+# CONFIG_BFIN_ICACHE_LOCK is not set
+# CONFIG_BFIN_WB is not set
+CONFIG_BFIN_WT=y
CONFIG_L1_MAX_PIECE=16
-#
-# Clock Settings
-#
-# CONFIG_BFIN_KERNEL_CLOCK is not set
-
#
# Asynchonous Memory Configuration
#
CONFIG_BANK_0=0x7BB0
CONFIG_BANK_1=0x7BB0
CONFIG_BANK_2=0x7BB0
-CONFIG_BANK_3=0x99B3
+CONFIG_BANK_3=0xAAC3
#
# Bus options (PCI, PCMCIA, EISA, MCA, ISA)
#
# CONFIG_PCI is not set
+# CONFIG_ARCH_SUPPORTS_MSI is not set
#
# PCCARD (PCMCIA/CardBus) support
#
# CONFIG_PCCARD is not set
-#
-# PCI Hotplug Support
-#
-
#
# Executable file formats
#
#
# Networking options
#
-# CONFIG_NETDEBUG is not set
CONFIG_PACKET=y
# CONFIG_PACKET_MMAP is not set
CONFIG_UNIX=y
# CONFIG_NETLABEL is not set
# CONFIG_NETWORK_SECMARK is not set
# CONFIG_NETFILTER is not set
-
-#
-# DCCP Configuration (EXPERIMENTAL)
-#
# CONFIG_IP_DCCP is not set
-
-#
-# SCTP Configuration (EXPERIMENTAL)
-#
# CONFIG_IP_SCTP is not set
-
-#
-# TIPC Configuration (EXPERIMENTAL)
-#
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# FIR device drivers
#
# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_MAC80211 is not set
# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
#
# Device Drivers
# Connector - unified userspace <-> kernelspace linker
#
# CONFIG_CONNECTOR is not set
-
-#
-# Memory Technology Devices (MTD)
-#
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
# CONFIG_MTD_CONCAT is not set
CONFIG_MTD_RAM=y
CONFIG_MTD_ROM=m
# CONFIG_MTD_ABSENT is not set
-# CONFIG_MTD_OBSOLETE_CHIPS is not set
#
# Mapping drivers for chip access
# CONFIG_MTD_DOC2000 is not set
# CONFIG_MTD_DOC2001 is not set
# CONFIG_MTD_DOC2001PLUS is not set
-
-#
-# NAND Flash Device Drivers
-#
# CONFIG_MTD_NAND is not set
+# CONFIG_MTD_ONENAND is not set
#
-# OneNAND Flash Device Drivers
+# UBI - Unsorted block images
#
-# CONFIG_MTD_ONENAND is not set
+# CONFIG_MTD_UBI is not set
#
# Parallel port support
#
# Misc devices
#
-
-#
-# ATA/ATAPI/MFM/RLL support
-#
# CONFIG_IDE is not set
#
# CONFIG_RAID_ATTRS is not set
# CONFIG_SCSI is not set
# CONFIG_SCSI_NETLINK is not set
-
-#
-# Serial ATA (prod) and Parallel ATA (experimental) drivers
-#
# CONFIG_ATA is not set
#
#
# CONFIG_MD is not set
-#
-# Fusion MPT device support
-#
-# CONFIG_FUSION is not set
-
-#
-# IEEE 1394 (FireWire) support
-#
-
-#
-# I2O device support
-#
-
#
# Network device support
#
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
-
-#
-# PHY device support
-#
# CONFIG_PHYLIB is not set
#
CONFIG_MII=y
CONFIG_SMC91X=y
# CONFIG_SMSC911X is not set
+# CONFIG_DM9000 is not set
+CONFIG_NETDEV_1000=y
+CONFIG_NETDEV_10000=y
#
-# Ethernet (1000 Mbit)
-#
-
-#
-# Ethernet (10000 Mbit)
-#
-
-#
-# Token Ring devices
-#
-
-#
-# Wireless LAN (non-hamradio)
-#
-# CONFIG_NET_RADIO is not set
-
-#
-# Wan interfaces
+# Wireless LAN
#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
# CONFIG_WAN is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
#
CONFIG_INPUT=m
# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
#
# Userland interfaces
# CONFIG_INPUT_KEYBOARD is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
# CONFIG_INPUT_MISC is not set
#
# CONFIG_AD9960 is not set
# CONFIG_SPI_ADC_BF533 is not set
-# CONFIG_BF5xx_PFLAGS is not set
+# CONFIG_BFIN_PFLAGS is not set
# CONFIG_BF5xx_PPIFCD is not set
# CONFIG_BF5xx_TIMERS is not set
# CONFIG_BF5xx_PPI is not set
# IPMI
#
# CONFIG_IPMI_HANDLER is not set
-
-#
-# Watchdog Cards
-#
CONFIG_WATCHDOG=y
# CONFIG_WATCHDOG_NOWAYOUT is not set
CONFIG_BFIN_WDT=y
CONFIG_HW_RANDOM=y
# CONFIG_GEN_RTC is not set
-# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_RAW_DRIVER is not set
# TPM devices
#
# CONFIG_TCG_TPM is not set
-
-#
-# I2C support
-#
# CONFIG_I2C is not set
#
# SPI Protocol Masters
#
# CONFIG_SPI_AT25 is not set
+# CONFIG_SPI_SPIDEV is not set
#
# Dallas's 1-wire bus
#
# CONFIG_W1 is not set
-
-#
-# Hardware Monitoring support
-#
CONFIG_HWMON=y
# CONFIG_HWMON_VID is not set
# CONFIG_SENSORS_ABITUGURU is not set
# CONFIG_SENSORS_F71805F is not set
# CONFIG_SENSORS_LM70 is not set
# CONFIG_SENSORS_PC87427 is not set
+# CONFIG_SENSORS_SMSC47M1 is not set
+# CONFIG_SENSORS_SMSC47B397 is not set
# CONFIG_SENSORS_VT1211 is not set
+# CONFIG_SENSORS_W83627HF is not set
# CONFIG_HWMON_DEBUG_CHIP is not set
#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+CONFIG_DAB=y
#
-# Digital Video Broadcasting Devices
+# Graphics support
#
-# CONFIG_DVB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
-# Graphics support
+# Display device support
#
-# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+# CONFIG_DISPLAY_SUPPORT is not set
+# CONFIG_VGASTATE is not set
# CONFIG_FB is not set
#
# CONFIG_USB is not set
#
-# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
+# Enable Host or Gadget support to see Inventra options
#
#
-# USB Gadget Support
+# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
#
-# CONFIG_USB_GADGET is not set
#
-# MMC/SD Card support
+# USB Gadget Support
#
-# CONFIG_SPI_MMC is not set
+# CONFIG_USB_GADGET is not set
# CONFIG_MMC is not set
#
# DMA Devices
#
-#
-# Auxiliary Display support
-#
-
-#
-# Virtualization
-#
-
#
# PBX support
#
CONFIG_LOCKD_V4=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=m
+# CONFIG_SUNRPC_BIND34 is not set
# CONFIG_RPCSEC_GSS_KRB5 is not set
# CONFIG_RPCSEC_GSS_SPKM3 is not set
CONFIG_SMB_FS=m
CONFIG_ENABLE_MUST_CHECK=y
# CONFIG_MAGIC_SYSRQ is not set
# CONFIG_UNUSED_SYMBOLS is not set
-# CONFIG_DEBUG_FS is not set
+CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_KERNEL is not set
-CONFIG_LOG_BUF_SHIFT=14
# CONFIG_DEBUG_BUGVERBOSE is not set
-# CONFIG_DEBUG_SERIAL_EARLY_INIT is not set
+CONFIG_DEBUG_MMRS=y
CONFIG_DEBUG_HUNT_FOR_ZERO=y
+CONFIG_DEBUG_BFIN_HWTRACE_ON=y
+CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION_OFF=y
+# CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION_ONE is not set
+# CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION_TWO is not set
+CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION=0
+# CONFIG_DEBUG_BFIN_HWTRACE_EXPAND is not set
# CONFIG_DEBUG_BFIN_NO_KERN_HWTRACE is not set
+CONFIG_EARLY_PRINTK=y
# CONFIG_DUAL_CORE_TEST_MODULE is not set
CONFIG_CPLB_INFO=y
CONFIG_ACCESS_CHECK=y
CONFIG_BITREVERSE=y
CONFIG_CRC_CCITT=m
# CONFIG_CRC16 is not set
+# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
# CONFIG_LIBCRC32C is not set
CONFIG_ZLIB_INFLATE=y
CONFIG_PLIST=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.21.5
+# Linux kernel version: 2.6.22.6
#
# CONFIG_MMU is not set
# CONFIG_FPU is not set
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
# CONFIG_GENERIC_TIME is not set
-CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_GPIO=y
CONFIG_FORCE_MAX_ZONEORDER=14
+CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_IRQCHIP_DEMUX_GPIO=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
# CONFIG_UTS_NS is not set
# CONFIG_AUDIT is not set
# CONFIG_IKCONFIG is not set
+CONFIG_LOG_BUF_SHIFT=14
CONFIG_SYSFS_DEPRECATED=y
# CONFIG_RELAY is not set
# CONFIG_BLK_DEV_INITRD is not set
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
+CONFIG_VM_EVENT_COUNTERS=y
CONFIG_BIG_ORDER_ALLOC_NOFAIL_MAGIC=9
-CONFIG_BUDDY=y
# CONFIG_NP2 is not set
CONFIG_SLAB=y
-CONFIG_VM_EVENT_COUNTERS=y
+# CONFIG_SLUB is not set
+# CONFIG_SLOB is not set
CONFIG_RT_MUTEXES=y
CONFIG_TINY_SHMEM=y
CONFIG_BASE_SMALL=0
-# CONFIG_SLOB is not set
#
# Loadable module support
# BF537 Specific Configuration
#
-#
-# PORT F/G Selection
-#
-CONFIG_BF537_PORT_F=y
-# CONFIG_BF537_PORT_G is not set
-# CONFIG_BF537_PORT_H is not set
-
#
# Interrupt Priority Assignment
#
# CONFIG_CMDLINE_BOOL is not set
#
-# Board Setup
+# Clock/PLL Setup
#
CONFIG_CLKIN_HZ=24576000
-CONFIG_MEM_SIZE=64
-CONFIG_MEM_ADD_WIDTH=10
-CONFIG_BOOT_LOAD=0x1000
-
-#
-# Blackfin Kernel Optimizations
-#
+# CONFIG_BFIN_KERNEL_CLOCK is not set
+CONFIG_MAX_VCO_HZ=600000000
+CONFIG_MIN_VCO_HZ=50000000
+CONFIG_MAX_SCLK_HZ=133000000
+CONFIG_MIN_SCLK_HZ=27000000
#
-# Timer Tick
+# Kernel Timer/Scheduler
#
# CONFIG_HZ_100 is not set
CONFIG_HZ_250=y
# CONFIG_HZ_1000 is not set
CONFIG_HZ=250
+#
+# Memory Setup
+#
+CONFIG_MEM_SIZE=64
+CONFIG_MEM_ADD_WIDTH=10
+CONFIG_BOOT_LOAD=0x1000
+CONFIG_BFIN_SCRATCH_REG_RETN=y
+# CONFIG_BFIN_SCRATCH_REG_RETE is not set
+# CONFIG_BFIN_SCRATCH_REG_CYCLES is not set
+
+#
+# Blackfin Kernel Optimizations
+#
+
#
# Memory Optimizations
#
#
# Cache Support
#
-CONFIG_BLKFIN_CACHE=y
-CONFIG_BLKFIN_DCACHE=y
-# CONFIG_BLKFIN_DCACHE_BANKA is not set
-# CONFIG_BLKFIN_CACHE_LOCK is not set
-CONFIG_BLKFIN_WB=y
-# CONFIG_BLKFIN_WT is not set
+CONFIG_BFIN_ICACHE=y
+CONFIG_BFIN_DCACHE=y
+# CONFIG_BFIN_DCACHE_BANKA is not set
+# CONFIG_BFIN_ICACHE_LOCK is not set
+CONFIG_BFIN_WB=y
+# CONFIG_BFIN_WT is not set
CONFIG_L1_MAX_PIECE=16
-#
-# Clock Settings
-#
-# CONFIG_BFIN_KERNEL_CLOCK is not set
-
#
# Asynchonous Memory Configuration
#
# Bus options (PCI, PCMCIA, EISA, MCA, ISA)
#
# CONFIG_PCI is not set
+# CONFIG_ARCH_SUPPORTS_MSI is not set
#
# PCCARD (PCMCIA/CardBus) support
#
# CONFIG_PCCARD is not set
-#
-# PCI Hotplug Support
-#
-
#
# Executable file formats
#
#
# Networking options
#
-# CONFIG_NETDEBUG is not set
CONFIG_PACKET=y
# CONFIG_PACKET_MMAP is not set
CONFIG_UNIX=y
# CONFIG_NETLABEL is not set
# CONFIG_NETWORK_SECMARK is not set
# CONFIG_NETFILTER is not set
-
-#
-# DCCP Configuration (EXPERIMENTAL)
-#
# CONFIG_IP_DCCP is not set
-
-#
-# SCTP Configuration (EXPERIMENTAL)
-#
# CONFIG_IP_SCTP is not set
-
-#
-# TIPC Configuration (EXPERIMENTAL)
-#
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_HAMRADIO is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_MAC80211 is not set
# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
#
# Device Drivers
# Connector - unified userspace <-> kernelspace linker
#
# CONFIG_CONNECTOR is not set
-
-#
-# Memory Technology Devices (MTD)
-#
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
# CONFIG_MTD_CONCAT is not set
CONFIG_MTD_RAM=y
# CONFIG_MTD_ROM is not set
# CONFIG_MTD_ABSENT is not set
-# CONFIG_MTD_OBSOLETE_CHIPS is not set
#
# Mapping drivers for chip access
# CONFIG_MTD_DOC2000 is not set
# CONFIG_MTD_DOC2001 is not set
# CONFIG_MTD_DOC2001PLUS is not set
-
-#
-# NAND Flash Device Drivers
-#
CONFIG_MTD_NAND=y
# CONFIG_MTD_NAND_VERIFY_WRITE is not set
# CONFIG_MTD_NAND_ECC_SMC is not set
+# CONFIG_MTD_NAND_MUSEUM_IDS is not set
CONFIG_MTD_NAND_BFIN=y
CONFIG_BFIN_NAND_BASE=0x20100000
CONFIG_BFIN_NAND_CLE=2
CONFIG_MTD_NAND_IDS=y
# CONFIG_MTD_NAND_DISKONCHIP is not set
# CONFIG_MTD_NAND_NANDSIM is not set
+# CONFIG_MTD_NAND_PLATFORM is not set
+# CONFIG_MTD_ONENAND is not set
#
-# OneNAND Flash Device Drivers
+# UBI - Unsorted block images
#
-# CONFIG_MTD_ONENAND is not set
+# CONFIG_MTD_UBI is not set
#
# Parallel port support
#
# Misc devices
#
-
-#
-# ATA/ATAPI/MFM/RLL support
-#
# CONFIG_IDE is not set
#
# CONFIG_RAID_ATTRS is not set
# CONFIG_SCSI is not set
# CONFIG_SCSI_NETLINK is not set
-
-#
-# Serial ATA (prod) and Parallel ATA (experimental) drivers
-#
# CONFIG_ATA is not set
#
#
# CONFIG_MD is not set
-#
-# Fusion MPT device support
-#
-# CONFIG_FUSION is not set
-
-#
-# IEEE 1394 (FireWire) support
-#
-
-#
-# I2O device support
-#
-
#
# Network device support
#
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
+CONFIG_PHYLIB=y
#
-# PHY device support
+# MII PHY device drivers
#
-# CONFIG_PHYLIB is not set
+# CONFIG_MARVELL_PHY is not set
+# CONFIG_DAVICOM_PHY is not set
+# CONFIG_QSEMI_PHY is not set
+# CONFIG_LXT_PHY is not set
+# CONFIG_CICADA_PHY is not set
+# CONFIG_VITESSE_PHY is not set
+# CONFIG_SMSC_PHY is not set
+# CONFIG_BROADCOM_PHY is not set
+# CONFIG_FIXED_PHY is not set
#
# Ethernet (10 or 100Mbit)
CONFIG_BFIN_RX_DESC_NUM=100
CONFIG_BFIN_MAC_RMII=y
# CONFIG_SMSC911X is not set
+# CONFIG_DM9000 is not set
+CONFIG_NETDEV_1000=y
+CONFIG_NETDEV_10000=y
#
-# Ethernet (1000 Mbit)
-#
-
-#
-# Ethernet (10000 Mbit)
-#
-
-#
-# Token Ring devices
-#
-
-#
-# Wireless LAN (non-hamradio)
-#
-# CONFIG_NET_RADIO is not set
-
-#
-# Wan interfaces
+# Wireless LAN
#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
# CONFIG_WAN is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
#
CONFIG_INPUT=y
# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
#
# Userland interfaces
# CONFIG_INPUT_KEYBOARD is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
CONFIG_INPUT_TOUCHSCREEN=y
# CONFIG_TOUCHSCREEN_ADS7846 is not set
CONFIG_TOUCHSCREEN_AD7877=y
# CONFIG_TOUCHSCREEN_TOUCHRIGHT is not set
# CONFIG_TOUCHSCREEN_TOUCHWIN is not set
# CONFIG_TOUCHSCREEN_UCB1400 is not set
+# CONFIG_TOUCHSCREEN_USB_COMPOSITE is not set
CONFIG_INPUT_MISC=y
+# CONFIG_INPUT_ATI_REMOTE is not set
+# CONFIG_INPUT_ATI_REMOTE2 is not set
+# CONFIG_INPUT_KEYSPAN_REMOTE is not set
+# CONFIG_INPUT_POWERMATE is not set
+# CONFIG_INPUT_YEALINK is not set
CONFIG_INPUT_UINPUT=y
# CONFIG_BF53X_PFBUTTONS is not set
# CONFIG_TWI_KEYPAD is not set
#
# CONFIG_AD9960 is not set
# CONFIG_SPI_ADC_BF533 is not set
-# CONFIG_BF5xx_PFLAGS is not set
+# CONFIG_BFIN_PFLAGS is not set
# CONFIG_BF5xx_PPIFCD is not set
# CONFIG_BF5xx_TIMERS is not set
# CONFIG_BF5xx_PPI is not set
# IPMI
#
# CONFIG_IPMI_HANDLER is not set
-
-#
-# Watchdog Cards
-#
# CONFIG_WATCHDOG is not set
CONFIG_HW_RANDOM=y
# CONFIG_GEN_RTC is not set
-# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_RAW_DRIVER is not set
# TPM devices
#
# CONFIG_TCG_TPM is not set
-
-#
-# I2C support
-#
CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
CONFIG_I2C_CHARDEV=y
#
# CONFIG_I2C_BLACKFIN_GPIO is not set
CONFIG_I2C_BLACKFIN_TWI=y
CONFIG_I2C_BLACKFIN_TWI_CLK_KHZ=50
+# CONFIG_I2C_GPIO is not set
# CONFIG_I2C_OCORES is not set
# CONFIG_I2C_PARPORT_LIGHT is not set
+# CONFIG_I2C_SIMTEC is not set
# CONFIG_I2C_STUB is not set
-# CONFIG_I2C_PCA_ISA is not set
#
# Miscellaneous I2C Chip support
# SPI Protocol Masters
#
# CONFIG_SPI_AT25 is not set
+# CONFIG_SPI_SPIDEV is not set
#
# Dallas's 1-wire bus
#
# CONFIG_W1 is not set
-
-#
-# Hardware Monitoring support
-#
CONFIG_HWMON=y
# CONFIG_HWMON_VID is not set
# CONFIG_SENSORS_ABITUGURU is not set
+# CONFIG_SENSORS_AD7418 is not set
# CONFIG_SENSORS_ADM1021 is not set
# CONFIG_SENSORS_ADM1025 is not set
# CONFIG_SENSORS_ADM1026 is not set
# CONFIG_SENSORS_LM90 is not set
# CONFIG_SENSORS_LM92 is not set
# CONFIG_SENSORS_MAX1619 is not set
+# CONFIG_SENSORS_MAX6650 is not set
# CONFIG_SENSORS_PC87360 is not set
# CONFIG_SENSORS_PC87427 is not set
# CONFIG_SENSORS_SMSC47M1 is not set
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
-
-#
-# Digital Video Broadcasting Devices
-#
-# CONFIG_DVB is not set
+# CONFIG_DVB_CORE is not set
+CONFIG_DAB=y
#
# Graphics support
CONFIG_BACKLIGHT_LCD_SUPPORT=y
CONFIG_BACKLIGHT_CLASS_DEVICE=y
CONFIG_LCD_CLASS_DEVICE=y
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
+# CONFIG_VGASTATE is not set
CONFIG_FB=y
CONFIG_FIRMWARE_EDID=y
# CONFIG_FB_DDC is not set
CONFIG_FB_CFB_FILLRECT=y
CONFIG_FB_CFB_COPYAREA=y
CONFIG_FB_CFB_IMAGEBLIT=y
+# CONFIG_FB_SYS_FILLRECT is not set
+# CONFIG_FB_SYS_COPYAREA is not set
+# CONFIG_FB_SYS_IMAGEBLIT is not set
+# CONFIG_FB_SYS_FOPS is not set
+CONFIG_FB_DEFERRED_IO=y
# CONFIG_FB_SVGALIB is not set
# CONFIG_FB_MACMODES is not set
# CONFIG_FB_BACKLIGHT is not set
# CONFIG_FB_BFIN_BGR is not set
# CONFIG_FB_S1D13XXX is not set
# CONFIG_FB_VIRTUAL is not set
-
-#
-# Logo configuration
-#
# CONFIG_LOGO is not set
#
# Advanced Linux Sound Architecture
#
CONFIG_SND=m
-CONFIG_SND_TIMER=m
-CONFIG_SND_PCM=m
# CONFIG_SND_SEQUENCER is not set
# CONFIG_SND_MIXER_OSS is not set
# CONFIG_SND_PCM_OSS is not set
# ALSA Blackfin devices
#
# CONFIG_SND_BLACKFIN_AD1836 is not set
-CONFIG_SND_BLACKFIN_AD1981B=m
# CONFIG_SND_BFIN_AD73311 is not set
#
-# SoC audio support
+# System on Chip audio support
#
# CONFIG_SND_SOC is not set
+#
+# SoC Audio for the ADI Blackfin
+#
+# CONFIG_SND_BF5XX_HAVE_COLD_RESET is not set
+
#
# Open Sound System
#
CONFIG_SOUND_PRIME=y
-# CONFIG_OBSOLETE_OSS is not set
+# CONFIG_OSS_OBSOLETE is not set
# CONFIG_SOUND_MSNDCLAS is not set
# CONFIG_SOUND_MSNDPIN is not set
# CONFIG_USB is not set
#
-# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
+# Enable Host or Gadget support to see Inventra options
#
#
-# USB Gadget Support
+# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
#
-# CONFIG_USB_GADGET is not set
#
-# MMC/SD Card support
+# USB Gadget Support
#
-# CONFIG_SPI_MMC is not set
+# CONFIG_USB_GADGET is not set
# CONFIG_MMC is not set
#
CONFIG_RTC_INTF_PROC=y
CONFIG_RTC_INTF_DEV=y
# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set
+# CONFIG_RTC_DRV_TEST is not set
#
-# RTC drivers
+# I2C RTC drivers
#
-# CONFIG_RTC_DRV_X1205 is not set
# CONFIG_RTC_DRV_DS1307 is not set
-# CONFIG_RTC_DRV_DS1553 is not set
-# CONFIG_RTC_DRV_ISL1208 is not set
# CONFIG_RTC_DRV_DS1672 is not set
-# CONFIG_RTC_DRV_DS1742 is not set
+# CONFIG_RTC_DRV_MAX6900 is not set
+# CONFIG_RTC_DRV_RS5C372 is not set
+# CONFIG_RTC_DRV_ISL1208 is not set
+# CONFIG_RTC_DRV_X1205 is not set
# CONFIG_RTC_DRV_PCF8563 is not set
+# CONFIG_RTC_DRV_PCF8583 is not set
+
+#
+# SPI RTC drivers
+#
# CONFIG_RTC_DRV_RS5C348 is not set
-# CONFIG_RTC_DRV_RS5C372 is not set
-# CONFIG_RTC_DRV_M48T86 is not set
-# CONFIG_RTC_DRV_TEST is not set
# CONFIG_RTC_DRV_MAX6902 is not set
-# CONFIG_RTC_DRV_V3020 is not set
-CONFIG_RTC_DRV_BFIN=y
#
-# DMA Engine support
+# Platform RTC drivers
#
-# CONFIG_DMA_ENGINE is not set
+# CONFIG_RTC_DRV_DS1553 is not set
+# CONFIG_RTC_DRV_DS1742 is not set
+# CONFIG_RTC_DRV_M48T86 is not set
+# CONFIG_RTC_DRV_V3020 is not set
#
-# DMA Clients
+# on-CPU RTC drivers
#
+CONFIG_RTC_DRV_BFIN=y
#
-# DMA Devices
+# DMA Engine support
#
+# CONFIG_DMA_ENGINE is not set
#
-# Auxiliary Display support
+# DMA Clients
#
#
-# Virtualization
+# DMA Devices
#
#
CONFIG_LOCKD_V4=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=m
+# CONFIG_SUNRPC_BIND34 is not set
# CONFIG_RPCSEC_GSS_KRB5 is not set
# CONFIG_RPCSEC_GSS_SPKM3 is not set
CONFIG_SMB_FS=m
# CONFIG_DEBUG_FS is not set
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_KERNEL is not set
-CONFIG_LOG_BUF_SHIFT=14
# CONFIG_DEBUG_BUGVERBOSE is not set
-# CONFIG_DEBUG_SERIAL_EARLY_INIT is not set
+# CONFIG_DEBUG_MMRS is not set
# CONFIG_DEBUG_HUNT_FOR_ZERO is not set
+CONFIG_DEBUG_BFIN_HWTRACE_ON=y
+CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION_OFF=y
+# CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION_ONE is not set
+# CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION_TWO is not set
+CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION=0
+# CONFIG_DEBUG_BFIN_HWTRACE_EXPAND is not set
# CONFIG_DEBUG_BFIN_NO_KERN_HWTRACE is not set
+# CONFIG_EARLY_PRINTK is not set
# CONFIG_CPLB_INFO is not set
# CONFIG_ACCESS_CHECK is not set
CONFIG_BITREVERSE=y
CONFIG_CRC_CCITT=m
# CONFIG_CRC16 is not set
+# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
# CONFIG_LIBCRC32C is not set
CONFIG_ZLIB_INFLATE=y
CONFIG_PLIST=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
obj-y := \
entry.o process.o bfin_ksyms.o ptrace.o setup.o signal.o \
sys_bfin.o time.o traps.o irqchip.o dma-mapping.o flat.o \
- fixed_code.o cplbinit.o cacheinit.o
+ fixed_code.o cplbinit.o cacheinit.o reboot.o bfin_gpio.o
-obj-$(CONFIG_BF53x) += bfin_gpio.o
-obj-$(CONFIG_BF561) += bfin_gpio.o
obj-$(CONFIG_MODULES) += module.o
obj-$(CONFIG_BFIN_DMA_5XX) += bfin_dma_5xx.o
obj-$(CONFIG_DUAL_CORE_TEST_MODULE) += dualcore_test.o
obj-$(CONFIG_KGDB) += kgdb.o
+obj-$(CONFIG_EARLY_PRINTK) += early_printk.o
/* Mark MEMDMA Channel 0 as requested since we're using it internally */
dma_ch[CH_MEM_STREAM0_DEST].chan_status = DMA_CHANNEL_REQUESTED;
dma_ch[CH_MEM_STREAM0_SRC].chan_status = DMA_CHANNEL_REQUESTED;
+
+#if defined(CONFIG_DEB_DMA_URGENT)
+ bfin_write_EBIU_DDRQUE(bfin_read_EBIU_DDRQUE()
+ | DEB1_URGENT | DEB2_URGENT | DEB3_URGENT);
+#endif
return 0;
}
dma_ch[channel].regs->next_desc_ptr = addr;
SSYNC();
- pr_debug("set_dma_start_addr() : END\n");
+ pr_debug("set_dma_next_desc_addr() : END\n");
}
EXPORT_SYMBOL(set_dma_next_desc_addr);
+void set_dma_curr_desc_addr(unsigned int channel, unsigned long addr)
+{
+ pr_debug("set_dma_curr_desc_addr() : BEGIN \n");
+
+ BUG_ON(!(dma_ch[channel].chan_status != DMA_CHANNEL_FREE
+ && channel < MAX_BLACKFIN_DMA_CHANNEL));
+
+ dma_ch[channel].regs->curr_desc_ptr = addr;
+ SSYNC();
+ pr_debug("set_dma_curr_desc_addr() : END\n");
+}
+EXPORT_SYMBOL(set_dma_curr_desc_addr);
+
void set_dma_x_count(unsigned int channel, unsigned short x_count)
{
BUG_ON(!(dma_ch[channel].chan_status != DMA_CHANNEL_FREE
}
EXPORT_SYMBOL(set_dma_sg);
+void set_dma_curr_addr(unsigned int channel, unsigned long addr)
+{
+ BUG_ON(!(dma_ch[channel].chan_status != DMA_CHANNEL_FREE
+ && channel < MAX_BLACKFIN_DMA_CHANNEL));
+
+ dma_ch[channel].regs->curr_addr_ptr = addr;
+ SSYNC();
+}
+EXPORT_SYMBOL(set_dma_curr_addr);
+
/*------------------------------------------------------------------------------
* Get the DMA status of a specific DMA channel from the system.
*-----------------------------------------------------------------------------*/
blackfin_dcache_flush_range((unsigned int)src,
(unsigned int)(src + size));
+ if ((unsigned long)dest < memory_end)
+ blackfin_dcache_invalidate_range((unsigned int)dest,
+ (unsigned int)(dest + size));
+
bfin_write_MDMA_D0_IRQ_STATUS(DMA_DONE | DMA_ERR);
if ((unsigned long)src < (unsigned long)dest)
}
}
+ SSYNC();
+
while (!(bfin_read_MDMA_D0_IRQ_STATUS() & DMA_DONE))
;
bfin_write_MDMA_S0_CONFIG(0);
bfin_write_MDMA_D0_CONFIG(0);
- if ((unsigned long)dest < memory_end)
- blackfin_dcache_invalidate_range((unsigned int)dest,
- (unsigned int)(dest + size));
local_irq_restore(flags);
return dest;
}
EXPORT_SYMBOL(safe_dma_memcpy);
-void dma_outsb(void __iomem *addr, const void *buf, unsigned short len)
+void dma_outsb(unsigned long addr, const void *buf, unsigned short len)
{
unsigned long flags;
local_irq_save(flags);
- blackfin_dcache_flush_range((unsigned int)buf, (unsigned int)(buf) + len);
+ blackfin_dcache_flush_range((unsigned int)buf,
+ (unsigned int)(buf) + len);
bfin_write_MDMA_D0_START_ADDR(addr);
bfin_write_MDMA_D0_X_COUNT(len);
bfin_write_MDMA_S0_CONFIG(DMAEN | WDSIZE_8);
bfin_write_MDMA_D0_CONFIG(WNR | DI_EN | DMAEN | WDSIZE_8);
+ SSYNC();
+
while (!(bfin_read_MDMA_D0_IRQ_STATUS() & DMA_DONE));
bfin_write_MDMA_D0_IRQ_STATUS(DMA_DONE | DMA_ERR);
EXPORT_SYMBOL(dma_outsb);
-void dma_insb(const void __iomem *addr, void *buf, unsigned short len)
+void dma_insb(unsigned long addr, void *buf, unsigned short len)
{
unsigned long flags;
+ blackfin_dcache_invalidate_range((unsigned int)buf,
+ (unsigned int)(buf) + len);
+
local_irq_save(flags);
bfin_write_MDMA_D0_START_ADDR(buf);
bfin_write_MDMA_D0_X_COUNT(len);
bfin_write_MDMA_S0_CONFIG(DMAEN | WDSIZE_8);
bfin_write_MDMA_D0_CONFIG(WNR | DI_EN | DMAEN | WDSIZE_8);
- blackfin_dcache_invalidate_range((unsigned int)buf, (unsigned int)(buf) + len);
+ SSYNC();
while (!(bfin_read_MDMA_D0_IRQ_STATUS() & DMA_DONE));
}
EXPORT_SYMBOL(dma_insb);
-void dma_outsw(void __iomem *addr, const void *buf, unsigned short len)
+void dma_outsw(unsigned long addr, const void *buf, unsigned short len)
{
unsigned long flags;
local_irq_save(flags);
- blackfin_dcache_flush_range((unsigned int)buf, (unsigned int)(buf) + len);
+ blackfin_dcache_flush_range((unsigned int)buf,
+ (unsigned int)(buf) + len * sizeof(short));
bfin_write_MDMA_D0_START_ADDR(addr);
bfin_write_MDMA_D0_X_COUNT(len);
bfin_write_MDMA_S0_CONFIG(DMAEN | WDSIZE_16);
bfin_write_MDMA_D0_CONFIG(WNR | DI_EN | DMAEN | WDSIZE_16);
+ SSYNC();
+
while (!(bfin_read_MDMA_D0_IRQ_STATUS() & DMA_DONE));
bfin_write_MDMA_D0_IRQ_STATUS(DMA_DONE | DMA_ERR);
}
EXPORT_SYMBOL(dma_outsw);
-void dma_insw(const void __iomem *addr, void *buf, unsigned short len)
+void dma_insw(unsigned long addr, void *buf, unsigned short len)
{
unsigned long flags;
+ blackfin_dcache_invalidate_range((unsigned int)buf,
+ (unsigned int)(buf) + len * sizeof(short));
+
local_irq_save(flags);
bfin_write_MDMA_D0_START_ADDR(buf);
bfin_write_MDMA_S0_CONFIG(DMAEN | WDSIZE_16);
bfin_write_MDMA_D0_CONFIG(WNR | DI_EN | DMAEN | WDSIZE_16);
- blackfin_dcache_invalidate_range((unsigned int)buf, (unsigned int)(buf) + len);
+ SSYNC();
while (!(bfin_read_MDMA_D0_IRQ_STATUS() & DMA_DONE));
}
EXPORT_SYMBOL(dma_insw);
-void dma_outsl(void __iomem *addr, const void *buf, unsigned short len)
+void dma_outsl(unsigned long addr, const void *buf, unsigned short len)
{
unsigned long flags;
local_irq_save(flags);
- blackfin_dcache_flush_range((unsigned int)buf, (unsigned int)(buf) + len);
+ blackfin_dcache_flush_range((unsigned int)buf,
+ (unsigned int)(buf) + len * sizeof(long));
bfin_write_MDMA_D0_START_ADDR(addr);
bfin_write_MDMA_D0_X_COUNT(len);
bfin_write_MDMA_S0_CONFIG(DMAEN | WDSIZE_32);
bfin_write_MDMA_D0_CONFIG(WNR | DI_EN | DMAEN | WDSIZE_32);
+ SSYNC();
+
while (!(bfin_read_MDMA_D0_IRQ_STATUS() & DMA_DONE));
bfin_write_MDMA_D0_IRQ_STATUS(DMA_DONE | DMA_ERR);
}
EXPORT_SYMBOL(dma_outsl);
-void dma_insl(const void __iomem *addr, void *buf, unsigned short len)
+void dma_insl(unsigned long addr, void *buf, unsigned short len)
{
unsigned long flags;
+ blackfin_dcache_invalidate_range((unsigned int)buf,
+ (unsigned int)(buf) + len * sizeof(long));
+
local_irq_save(flags);
bfin_write_MDMA_D0_START_ADDR(buf);
bfin_write_MDMA_S0_CONFIG(DMAEN | WDSIZE_32);
bfin_write_MDMA_D0_CONFIG(WNR | DI_EN | DMAEN | WDSIZE_32);
- blackfin_dcache_invalidate_range((unsigned int)buf, (unsigned int)(buf) + len);
+ SSYNC();
while (!(bfin_read_MDMA_D0_IRQ_STATUS() & DMA_DONE));
* Description: GPIO Abstraction Layer
*
* Modified:
- * Copyright 2006 Analog Devices Inc.
+ * Copyright 2007 Analog Devices Inc.
*
* Bugs: Enter bugs at http://blackfin.uclinux.org/
*
*/
/*
-* Number BF537/6/4 BF561 BF533/2/1
+* Number BF537/6/4 BF561 BF533/2/1 BF549/8/4/2
*
-* GPIO_0 PF0 PF0 PF0
+* GPIO_0 PF0 PF0 PF0 PA0...PJ13
* GPIO_1 PF1 PF1 PF1
* GPIO_2 PF2 PF2 PF2
* GPIO_3 PF3 PF3 PF3
* GPIO_47 PH15 PF47
*/
+#include <linux/delay.h>
#include <linux/module.h>
#include <linux/err.h>
#include <asm/blackfin.h>
#include <asm/portmux.h>
#include <linux/irq.h>
+#if ANOMALY_05000311 || ANOMALY_05000323
+enum {
+ AWA_data = SYSCR,
+ AWA_data_clear = SYSCR,
+ AWA_data_set = SYSCR,
+ AWA_toggle = SYSCR,
+ AWA_maska = UART_SCR,
+ AWA_maska_clear = UART_SCR,
+ AWA_maska_set = UART_SCR,
+ AWA_maska_toggle = UART_SCR,
+ AWA_maskb = UART_GCTL,
+ AWA_maskb_clear = UART_GCTL,
+ AWA_maskb_set = UART_GCTL,
+ AWA_maskb_toggle = UART_GCTL,
+ AWA_dir = SPORT1_STAT,
+ AWA_polar = SPORT1_STAT,
+ AWA_edge = SPORT1_STAT,
+ AWA_both = SPORT1_STAT,
+#if ANOMALY_05000311
+ AWA_inen = TIMER_ENABLE,
+#elif ANOMALY_05000323
+ AWA_inen = DMA1_1_CONFIG,
+#endif
+};
+ /* Anomaly Workaround */
+#define AWA_DUMMY_READ(name) bfin_read16(AWA_ ## name)
+#else
+#define AWA_DUMMY_READ(...) do { } while (0)
+#endif
+
#ifdef BF533_FAMILY
static struct gpio_port_t *gpio_bankb[gpio_bank(MAX_BLACKFIN_GPIOS)] = {
(struct gpio_port_t *) FIO_FLAG_D,
};
#endif
+#ifdef BF548_FAMILY
+static struct gpio_port_t *gpio_array[gpio_bank(MAX_BLACKFIN_GPIOS)] = {
+ (struct gpio_port_t *)PORTA_FER,
+ (struct gpio_port_t *)PORTB_FER,
+ (struct gpio_port_t *)PORTC_FER,
+ (struct gpio_port_t *)PORTD_FER,
+ (struct gpio_port_t *)PORTE_FER,
+ (struct gpio_port_t *)PORTF_FER,
+ (struct gpio_port_t *)PORTG_FER,
+ (struct gpio_port_t *)PORTH_FER,
+ (struct gpio_port_t *)PORTI_FER,
+ (struct gpio_port_t *)PORTJ_FER,
+};
+#endif
+
static unsigned short reserved_gpio_map[gpio_bank(MAX_BLACKFIN_GPIOS)];
static unsigned short reserved_peri_map[gpio_bank(MAX_BLACKFIN_GPIOS + 16)];
-char *str_ident = NULL;
-#define RESOURCE_LABEL_SIZE 16
+#define MAX_RESOURCES 256
+#define RESOURCE_LABEL_SIZE 16
+
+struct str_ident {
+ char name[RESOURCE_LABEL_SIZE];
+} *str_ident;
+
#ifdef CONFIG_PM
static unsigned short wakeup_map[gpio_bank(MAX_BLACKFIN_GPIOS)];
#endif /* CONFIG_PM */
+#if defined(BF548_FAMILY)
+inline int check_gpio(unsigned short gpio)
+{
+ if (gpio == GPIO_PB15 || gpio == GPIO_PC14 || gpio == GPIO_PC15
+ || gpio == GPIO_PH14 || gpio == GPIO_PH15
+ || gpio == GPIO_PJ14 || gpio == GPIO_PJ15
+ || gpio > MAX_BLACKFIN_GPIOS)
+ return -EINVAL;
+ return 0;
+}
+#else
inline int check_gpio(unsigned short gpio)
{
if (gpio >= MAX_BLACKFIN_GPIOS)
return -EINVAL;
return 0;
}
+#endif
static void set_label(unsigned short ident, const char *label)
{
if (label && str_ident) {
- strncpy(str_ident + ident * RESOURCE_LABEL_SIZE, label,
+ strncpy(str_ident[ident].name, label,
RESOURCE_LABEL_SIZE);
- str_ident[ident * RESOURCE_LABEL_SIZE +
- RESOURCE_LABEL_SIZE - 1] = 0;
+ str_ident[ident].name[RESOURCE_LABEL_SIZE - 1] = 0;
}
}
if (!str_ident)
return "UNKNOWN";
- return (str_ident[ident * RESOURCE_LABEL_SIZE] ?
- (str_ident + ident * RESOURCE_LABEL_SIZE) : "UNKNOWN");
+ return (*str_ident[ident].name ? str_ident[ident].name : "UNKNOWN");
}
static int cmp_label(unsigned short ident, const char *label)
{
if (label && str_ident)
- return strncmp(str_ident + ident * RESOURCE_LABEL_SIZE,
+ return strncmp(str_ident[ident].name,
label, strlen(label));
else
return -EINVAL;
static void port_setup(unsigned short gpio, unsigned short usage)
{
if (!check_gpio(gpio)) {
- if (usage == GPIO_USAGE) {
+ if (usage == GPIO_USAGE)
*port_fer[gpio_bank(gpio)] &= ~gpio_bit(gpio);
- } else
+ else
*port_fer[gpio_bank(gpio)] |= gpio_bit(gpio);
SSYNC();
}
}
+#elif defined(BF548_FAMILY)
+static void port_setup(unsigned short gpio, unsigned short usage)
+{
+ if (usage == GPIO_USAGE)
+ gpio_array[gpio_bank(gpio)]->port_fer &= ~gpio_bit(gpio);
+ else
+ gpio_array[gpio_bank(gpio)]->port_fer |= gpio_bit(gpio);
+ SSYNC();
+}
#else
# define port_setup(...) do { } while (0)
#endif
#ifdef BF537_FAMILY
-
-#define PMUX_LUT_RES 0
-#define PMUX_LUT_OFFSET 1
-#define PMUX_LUT_ENTRIES 41
-#define PMUX_LUT_SIZE 2
-
-static unsigned short port_mux_lut[PMUX_LUT_ENTRIES][PMUX_LUT_SIZE] = {
- {P_PPI0_D13, 11}, {P_PPI0_D14, 11}, {P_PPI0_D15, 11},
- {P_SPORT1_TFS, 11}, {P_SPORT1_TSCLK, 11}, {P_SPORT1_DTPRI, 11},
- {P_PPI0_D10, 10}, {P_PPI0_D11, 10}, {P_PPI0_D12, 10},
- {P_SPORT1_RSCLK, 10}, {P_SPORT1_RFS, 10}, {P_SPORT1_DRPRI, 10},
- {P_PPI0_D8, 9}, {P_PPI0_D9, 9}, {P_SPORT1_DRSEC, 9},
- {P_SPORT1_DTSEC, 9}, {P_TMR2, 8}, {P_PPI0_FS3, 8}, {P_TMR3, 7},
- {P_SPI0_SSEL4, 7}, {P_TMR4, 6}, {P_SPI0_SSEL5, 6}, {P_TMR5, 5},
- {P_SPI0_SSEL6, 5}, {P_UART1_RX, 4}, {P_UART1_TX, 4}, {P_TMR6, 4},
- {P_TMR7, 4}, {P_UART0_RX, 3}, {P_UART0_TX, 3}, {P_DMAR0, 3},
- {P_DMAR1, 3}, {P_SPORT0_DTSEC, 1}, {P_SPORT0_DRSEC, 1},
- {P_CAN0_RX, 1}, {P_CAN0_TX, 1}, {P_SPI0_SSEL7, 1},
- {P_SPORT0_TFS, 0}, {P_SPORT0_DTPRI, 0}, {P_SPI0_SSEL2, 0},
- {P_SPI0_SSEL3, 0}
+static struct {
+ unsigned short res;
+ unsigned short offset;
+} port_mux_lut[] = {
+ {.res = P_PPI0_D13, .offset = 11},
+ {.res = P_PPI0_D14, .offset = 11},
+ {.res = P_PPI0_D15, .offset = 11},
+ {.res = P_SPORT1_TFS, .offset = 11},
+ {.res = P_SPORT1_TSCLK, .offset = 11},
+ {.res = P_SPORT1_DTPRI, .offset = 11},
+ {.res = P_PPI0_D10, .offset = 10},
+ {.res = P_PPI0_D11, .offset = 10},
+ {.res = P_PPI0_D12, .offset = 10},
+ {.res = P_SPORT1_RSCLK, .offset = 10},
+ {.res = P_SPORT1_RFS, .offset = 10},
+ {.res = P_SPORT1_DRPRI, .offset = 10},
+ {.res = P_PPI0_D8, .offset = 9},
+ {.res = P_PPI0_D9, .offset = 9},
+ {.res = P_SPORT1_DRSEC, .offset = 9},
+ {.res = P_SPORT1_DTSEC, .offset = 9},
+ {.res = P_TMR2, .offset = 8},
+ {.res = P_PPI0_FS3, .offset = 8},
+ {.res = P_TMR3, .offset = 7},
+ {.res = P_SPI0_SSEL4, .offset = 7},
+ {.res = P_TMR4, .offset = 6},
+ {.res = P_SPI0_SSEL5, .offset = 6},
+ {.res = P_TMR5, .offset = 5},
+ {.res = P_SPI0_SSEL6, .offset = 5},
+ {.res = P_UART1_RX, .offset = 4},
+ {.res = P_UART1_TX, .offset = 4},
+ {.res = P_TMR6, .offset = 4},
+ {.res = P_TMR7, .offset = 4},
+ {.res = P_UART0_RX, .offset = 3},
+ {.res = P_UART0_TX, .offset = 3},
+ {.res = P_DMAR0, .offset = 3},
+ {.res = P_DMAR1, .offset = 3},
+ {.res = P_SPORT0_DTSEC, .offset = 1},
+ {.res = P_SPORT0_DRSEC, .offset = 1},
+ {.res = P_CAN0_RX, .offset = 1},
+ {.res = P_CAN0_TX, .offset = 1},
+ {.res = P_SPI0_SSEL7, .offset = 1},
+ {.res = P_SPORT0_TFS, .offset = 0},
+ {.res = P_SPORT0_DTPRI, .offset = 0},
+ {.res = P_SPI0_SSEL2, .offset = 0},
+ {.res = P_SPI0_SSEL3, .offset = 0},
};
static void portmux_setup(unsigned short per, unsigned short function)
{
- u16 y, muxreg, offset;
+ u16 y, offset, muxreg;
- for (y = 0; y < PMUX_LUT_ENTRIES; y++) {
- if (port_mux_lut[y][PMUX_LUT_RES] == per) {
+ for (y = 0; y < ARRAY_SIZE(port_mux_lut); y++) {
+ if (port_mux_lut[y].res == per) {
/* SET PORTMUX REG */
- offset = port_mux_lut[y][PMUX_LUT_OFFSET];
+ offset = port_mux_lut[y].offset;
muxreg = bfin_read_PORT_MUX();
if (offset != 1) {
}
}
}
+#elif defined(BF548_FAMILY)
+inline void portmux_setup(unsigned short portno, unsigned short function)
+{
+ u32 pmux;
+
+ pmux = gpio_array[gpio_bank(portno)]->port_mux;
+
+ pmux &= ~(0x3 << (2 * gpio_sub_n(portno)));
+ pmux |= (function & 0x3) << (2 * gpio_sub_n(portno));
+ gpio_array[gpio_bank(portno)]->port_mux = pmux;
+}
+
+inline u16 get_portmux(unsigned short portno)
+{
+ u32 pmux;
+
+ pmux = gpio_array[gpio_bank(portno)]->port_mux;
+
+ return (pmux >> (2 * gpio_sub_n(portno)) & 0x3);
+}
#else
# define portmux_setup(...) do { } while (0)
#endif
+#ifndef BF548_FAMILY
static void default_gpio(unsigned short gpio)
{
unsigned short bank, bitmask;
+ unsigned long flags;
bank = gpio_bank(gpio);
bitmask = gpio_bit(gpio);
+ local_irq_save(flags);
+
gpio_bankb[bank]->maska_clear = bitmask;
gpio_bankb[bank]->maskb_clear = bitmask;
SSYNC();
gpio_bankb[bank]->polar &= ~bitmask;
gpio_bankb[bank]->both &= ~bitmask;
gpio_bankb[bank]->edge &= ~bitmask;
+ AWA_DUMMY_READ(edge);
+ local_irq_restore(flags);
+
}
+#else
+# define default_gpio(...) do { } while (0)
+#endif
static int __init bfin_gpio_init(void)
{
-
- str_ident = kzalloc(RESOURCE_LABEL_SIZE * 256, GFP_KERNEL);
- if (!str_ident)
+ str_ident = kcalloc(MAX_RESOURCES,
+ sizeof(struct str_ident), GFP_KERNEL);
+ if (str_ident == NULL)
return -ENOMEM;
+ memset(str_ident, 0, MAX_RESOURCES * sizeof(struct str_ident));
+
printk(KERN_INFO "Blackfin GPIO Controller\n");
return 0;
}
-
arch_initcall(bfin_gpio_init);
+#ifndef BF548_FAMILY
/***********************************************************
*
* FUNCTIONS: Blackfin General Purpose Ports Access Functions
gpio_bankb[gpio_bank(gpio)]->name |= gpio_bit(gpio); \
else \
gpio_bankb[gpio_bank(gpio)]->name &= ~gpio_bit(gpio); \
+ AWA_DUMMY_READ(name); \
local_irq_restore(flags); \
} \
EXPORT_SYMBOL(set_gpio_ ## name);
SET_GPIO(both)
+#if ANOMALY_05000311 || ANOMALY_05000323
+#define SET_GPIO_SC(name) \
+void set_gpio_ ## name(unsigned short gpio, unsigned short arg) \
+{ \
+ unsigned long flags; \
+ BUG_ON(!(reserved_gpio_map[gpio_bank(gpio)] & gpio_bit(gpio))); \
+ local_irq_save(flags); \
+ if (arg) \
+ gpio_bankb[gpio_bank(gpio)]->name ## _set = gpio_bit(gpio); \
+ else \
+ gpio_bankb[gpio_bank(gpio)]->name ## _clear = gpio_bit(gpio); \
+ AWA_DUMMY_READ(name); \
+ local_irq_restore(flags); \
+} \
+EXPORT_SYMBOL(set_gpio_ ## name);
+#else
#define SET_GPIO_SC(name) \
void set_gpio_ ## name(unsigned short gpio, unsigned short arg) \
{ \
gpio_bankb[gpio_bank(gpio)]->name ## _clear = gpio_bit(gpio); \
} \
EXPORT_SYMBOL(set_gpio_ ## name);
+#endif
SET_GPIO_SC(maska)
SET_GPIO_SC(maskb)
-
-#if defined(ANOMALY_05000311)
-void set_gpio_data(unsigned short gpio, unsigned short arg)
-{
- unsigned long flags;
- BUG_ON(!(reserved_gpio_map[gpio_bank(gpio)] & gpio_bit(gpio)));
- local_irq_save(flags);
- if (arg)
- gpio_bankb[gpio_bank(gpio)]->data_set = gpio_bit(gpio);
- else
- gpio_bankb[gpio_bank(gpio)]->data_clear = gpio_bit(gpio);
- bfin_read_CHIPID();
- local_irq_restore(flags);
-}
-EXPORT_SYMBOL(set_gpio_data);
-#else
SET_GPIO_SC(data)
-#endif
-
-#if defined(ANOMALY_05000311)
+#if ANOMALY_05000311 || ANOMALY_05000323
void set_gpio_toggle(unsigned short gpio)
{
unsigned long flags;
BUG_ON(!(reserved_gpio_map[gpio_bank(gpio)] & gpio_bit(gpio)));
local_irq_save(flags);
gpio_bankb[gpio_bank(gpio)]->toggle = gpio_bit(gpio);
- bfin_read_CHIPID();
+ AWA_DUMMY_READ(toggle);
local_irq_restore(flags);
}
#else
/*Set current PORT date (16-bit word)*/
+#if ANOMALY_05000311 || ANOMALY_05000323
#define SET_GPIO_P(name) \
void set_gpiop_ ## name(unsigned short gpio, unsigned short arg) \
{ \
+ unsigned long flags; \
+ local_irq_save(flags); \
gpio_bankb[gpio_bank(gpio)]->name = arg; \
+ AWA_DUMMY_READ(name); \
+ local_irq_restore(flags); \
} \
EXPORT_SYMBOL(set_gpiop_ ## name);
+#else
+#define SET_GPIO_P(name) \
+void set_gpiop_ ## name(unsigned short gpio, unsigned short arg) \
+{ \
+ gpio_bankb[gpio_bank(gpio)]->name = arg; \
+} \
+EXPORT_SYMBOL(set_gpiop_ ## name);
+#endif
+SET_GPIO_P(data)
SET_GPIO_P(dir)
SET_GPIO_P(inen)
SET_GPIO_P(polar)
SET_GPIO_P(maskb)
-#if defined(ANOMALY_05000311)
-void set_gpiop_data(unsigned short gpio, unsigned short arg)
-{
- unsigned long flags;
- local_irq_save(flags);
- gpio_bankb[gpio_bank(gpio)]->data = arg;
- bfin_read_CHIPID();
- local_irq_restore(flags);
-}
-EXPORT_SYMBOL(set_gpiop_data);
-#else
-SET_GPIO_P(data)
-#endif
-
-
-
/* Get a specific bit */
-
+#if ANOMALY_05000311 || ANOMALY_05000323
+#define GET_GPIO(name) \
+unsigned short get_gpio_ ## name(unsigned short gpio) \
+{ \
+ unsigned long flags; \
+ unsigned short ret; \
+ local_irq_save(flags); \
+ ret = 0x01 & (gpio_bankb[gpio_bank(gpio)]->name >> gpio_sub_n(gpio)); \
+ AWA_DUMMY_READ(name); \
+ local_irq_restore(flags); \
+ return ret; \
+} \
+EXPORT_SYMBOL(get_gpio_ ## name);
+#else
#define GET_GPIO(name) \
unsigned short get_gpio_ ## name(unsigned short gpio) \
{ \
return (0x01 & (gpio_bankb[gpio_bank(gpio)]->name >> gpio_sub_n(gpio))); \
} \
EXPORT_SYMBOL(get_gpio_ ## name);
+#endif
+GET_GPIO(data)
GET_GPIO(dir)
GET_GPIO(inen)
GET_GPIO(polar)
GET_GPIO(maska)
GET_GPIO(maskb)
-
-#if defined(ANOMALY_05000311)
-unsigned short get_gpio_data(unsigned short gpio)
-{
- unsigned long flags;
- unsigned short ret;
- BUG_ON(!(reserved_gpio_map[gpio_bank(gpio)] & gpio_bit(gpio)));
- local_irq_save(flags);
- ret = 0x01 & (gpio_bankb[gpio_bank(gpio)]->data >> gpio_sub_n(gpio));
- bfin_read_CHIPID();
- local_irq_restore(flags);
- return ret;
-}
-EXPORT_SYMBOL(get_gpio_data);
-#else
-GET_GPIO(data)
-#endif
-
/*Get current PORT date (16-bit word)*/
+#if ANOMALY_05000311 || ANOMALY_05000323
+#define GET_GPIO_P(name) \
+unsigned short get_gpiop_ ## name(unsigned short gpio) \
+{ \
+ unsigned long flags; \
+ unsigned short ret; \
+ local_irq_save(flags); \
+ ret = (gpio_bankb[gpio_bank(gpio)]->name); \
+ AWA_DUMMY_READ(name); \
+ local_irq_restore(flags); \
+ return ret; \
+} \
+EXPORT_SYMBOL(get_gpiop_ ## name);
+#else
#define GET_GPIO_P(name) \
unsigned short get_gpiop_ ## name(unsigned short gpio) \
{ \
return (gpio_bankb[gpio_bank(gpio)]->name);\
} \
EXPORT_SYMBOL(get_gpiop_ ## name);
+#endif
+GET_GPIO_P(data)
GET_GPIO_P(dir)
GET_GPIO_P(inen)
GET_GPIO_P(polar)
GET_GPIO_P(maska)
GET_GPIO_P(maskb)
-#if defined(ANOMALY_05000311)
-unsigned short get_gpiop_data(unsigned short gpio)
-{
- unsigned long flags;
- unsigned short ret;
- local_irq_save(flags);
- ret = gpio_bankb[gpio_bank(gpio)]->data;
- bfin_read_CHIPID();
- local_irq_restore(flags);
- return ret;
-}
-EXPORT_SYMBOL(get_gpiop_data);
-#else
-GET_GPIO_P(data)
-#endif
#ifdef CONFIG_PM
/***********************************************************
}
}
+ AWA_DUMMY_READ(maskb_set);
+
if (sic_iwr)
return sic_iwr;
else
gpio_bankb[bank]->maskb = gpio_bank_saved[bank].maskb;
}
+ AWA_DUMMY_READ(maskb);
}
#endif
+#endif /* BF548_FAMILY */
+/***********************************************************
+*
+* FUNCTIONS: Blackfin Peripheral Resource Allocation
+* and PortMux Setup
+*
+* INPUTS/OUTPUTS:
+* per Peripheral Identifier
+* label String
+*
+* DESCRIPTION: Blackfin Peripheral Resource Allocation and Setup API
+*
+* CAUTION:
+*************************************************************
+* MODIFICATION HISTORY :
+**************************************************************/
+
+#ifdef BF548_FAMILY
+int peripheral_request(unsigned short per, const char *label)
+{
+ unsigned long flags;
+ unsigned short ident = P_IDENT(per);
+
+ /*
+ * Don't cares are pins with only one dedicated function
+ */
+
+ if (per & P_DONTCARE)
+ return 0;
+
+ if (!(per & P_DEFINED))
+ return -ENODEV;
+
+ if (check_gpio(ident) < 0)
+ return -EINVAL;
+
+ local_irq_save(flags);
+
+ if (unlikely(reserved_gpio_map[gpio_bank(ident)] & gpio_bit(ident))) {
+ printk(KERN_ERR
+ "%s: Peripheral %d is already reserved as GPIO by %s !\n",
+ __FUNCTION__, ident, get_label(ident));
+ dump_stack();
+ local_irq_restore(flags);
+ return -EBUSY;
+ }
+
+ if (unlikely(reserved_peri_map[gpio_bank(ident)] & gpio_bit(ident))) {
+
+ u16 funct = get_portmux(ident);
+
+ /*
+ * Pin functions like AMC address strobes my
+ * be requested and used by several drivers
+ */
+
+ if (!((per & P_MAYSHARE) && (funct == P_FUNCT2MUX(per)))) {
+
+ /*
+ * Allow that the identical pin function can
+ * be requested from the same driver twice
+ */
+
+ if (cmp_label(ident, label) == 0)
+ goto anyway;
+ printk(KERN_ERR
+ "%s: Peripheral %d function %d is already reserved by %s !\n",
+ __FUNCTION__, ident, P_FUNCT2MUX(per), get_label(ident));
+ dump_stack();
+ local_irq_restore(flags);
+ return -EBUSY;
+ }
+ }
+anyway:
+ reserved_peri_map[gpio_bank(ident)] |= gpio_bit(ident);
+
+ portmux_setup(ident, P_FUNCT2MUX(per));
+ port_setup(ident, PERIPHERAL_USAGE);
+
+ local_irq_restore(flags);
+ set_label(ident, label);
+
+ return 0;
+}
+EXPORT_SYMBOL(peripheral_request);
+#else
int peripheral_request(unsigned short per, const char *label)
{
printk(KERN_ERR
"%s: Peripheral %d function %d is already"
- "reserved by %s !\n",
+ " reserved by %s !\n",
__FUNCTION__, ident, P_FUNCT2MUX(per),
get_label(ident));
dump_stack();
}
anyway:
-
-
portmux_setup(per, P_FUNCT2MUX(per));
port_setup(ident, PERIPHERAL_USAGE);
return 0;
}
EXPORT_SYMBOL(peripheral_request);
+#endif
int peripheral_request_list(unsigned short per[], const char *label)
{
int ret;
for (cnt = 0; per[cnt] != 0; cnt++) {
+
ret = peripheral_request(per[cnt], label);
- if (ret < 0)
- return ret;
+
+ if (ret < 0) {
+ for ( ; cnt > 0; cnt--) {
+ peripheral_free(per[cnt - 1]);
+ }
+ return ret;
+ }
}
return 0;
reserved_peri_map[gpio_bank(ident)] &= ~gpio_bit(ident);
+ set_label(ident, "free");
+
local_irq_restore(flags);
}
EXPORT_SYMBOL(peripheral_free);
* FUNCTIONS: Blackfin GPIO Driver
*
* INPUTS/OUTPUTS:
-* gpio - GPIO Number between 0 and MAX_BLACKFIN_GPIOS
-*
+* gpio PIO Number between 0 and MAX_BLACKFIN_GPIOS
+* label String
*
* DESCRIPTION: Blackfin GPIO Driver API
*
local_irq_save(flags);
+ /*
+ * Allow that the identical GPIO can
+ * be requested from the same driver twice
+ * Do nothing and return -
+ */
+
+ if (cmp_label(gpio, label) == 0) {
+ local_irq_restore(flags);
+ return 0;
+ }
+
if (unlikely(reserved_gpio_map[gpio_bank(gpio)] & gpio_bit(gpio))) {
- printk(KERN_ERR "bfin-gpio: GPIO %d is already reserved!\n", gpio);
+ printk(KERN_ERR "bfin-gpio: GPIO %d is already reserved by %s !\n",
+ gpio, get_label(gpio));
dump_stack();
local_irq_restore(flags);
return -EBUSY;
}
+ if (unlikely(reserved_peri_map[gpio_bank(gpio)] & gpio_bit(gpio))) {
+ printk(KERN_ERR
+ "bfin-gpio: GPIO %d is already reserved as Peripheral by %s !\n",
+ gpio, get_label(gpio));
+ dump_stack();
+ local_irq_restore(flags);
+ return -EBUSY;
+ }
+
reserved_gpio_map[gpio_bank(gpio)] |= gpio_bit(gpio);
local_irq_restore(flags);
port_setup(gpio, GPIO_USAGE);
+ set_label(gpio, label);
return 0;
}
reserved_gpio_map[gpio_bank(gpio)] &= ~gpio_bit(gpio);
+ set_label(gpio, "free");
+
local_irq_restore(flags);
}
EXPORT_SYMBOL(gpio_free);
+#ifdef BF548_FAMILY
+void gpio_direction_input(unsigned short gpio)
+{
+ unsigned long flags;
+
+ BUG_ON(!(reserved_gpio_map[gpio_bank(gpio)] & gpio_bit(gpio)));
+
+ local_irq_save(flags);
+ gpio_array[gpio_bank(gpio)]->port_dir_clear = gpio_bit(gpio);
+ gpio_array[gpio_bank(gpio)]->port_inen |= gpio_bit(gpio);
+ local_irq_restore(flags);
+}
+EXPORT_SYMBOL(gpio_direction_input);
+
+void gpio_direction_output(unsigned short gpio)
+{
+ unsigned long flags;
+
+ BUG_ON(!(reserved_gpio_map[gpio_bank(gpio)] & gpio_bit(gpio)));
+
+ local_irq_save(flags);
+ gpio_array[gpio_bank(gpio)]->port_inen &= ~gpio_bit(gpio);
+ gpio_array[gpio_bank(gpio)]->port_dir_set = gpio_bit(gpio);
+ local_irq_restore(flags);
+}
+EXPORT_SYMBOL(gpio_direction_output);
+
+void gpio_set_value(unsigned short gpio, unsigned short arg)
+{
+ if (arg)
+ gpio_array[gpio_bank(gpio)]->port_set = gpio_bit(gpio);
+ else
+ gpio_array[gpio_bank(gpio)]->port_clear = gpio_bit(gpio);
+
+}
+EXPORT_SYMBOL(gpio_set_value);
+
+unsigned short gpio_get_value(unsigned short gpio)
+{
+ return (1 & (gpio_array[gpio_bank(gpio)]->port_data >> gpio_sub_n(gpio)));
+}
+EXPORT_SYMBOL(gpio_get_value);
+
+#else
+
void gpio_direction_input(unsigned short gpio)
{
unsigned long flags;
local_irq_save(flags);
gpio_bankb[gpio_bank(gpio)]->dir &= ~gpio_bit(gpio);
gpio_bankb[gpio_bank(gpio)]->inen |= gpio_bit(gpio);
+ AWA_DUMMY_READ(inen);
local_irq_restore(flags);
}
EXPORT_SYMBOL(gpio_direction_input);
local_irq_save(flags);
gpio_bankb[gpio_bank(gpio)]->inen &= ~gpio_bit(gpio);
gpio_bankb[gpio_bank(gpio)]->dir |= gpio_bit(gpio);
+ AWA_DUMMY_READ(dir);
local_irq_restore(flags);
}
EXPORT_SYMBOL(gpio_direction_output);
+
+/* If we are booting from SPI and our board lacks a strong enough pull up,
+ * the core can reset and execute the bootrom faster than the resistor can
+ * pull the signal logically high. To work around this (common) error in
+ * board design, we explicitly set the pin back to GPIO mode, force /CS
+ * high, and wait for the electrons to do their thing.
+ *
+ * This function only makes sense to be called from reset code, but it
+ * lives here as we need to force all the GPIO states w/out going through
+ * BUG() checks and such.
+ */
+void bfin_gpio_reset_spi0_ssel1(void)
+{
+ u16 gpio = P_IDENT(P_SPI0_SSEL1);
+
+ port_setup(gpio, GPIO_USAGE);
+ gpio_bankb[gpio_bank(gpio)]->data_set = gpio_bit(gpio);
+ udelay(1);
+}
+
+#endif /*BF548_FAMILY */
* their interface isn't gonna change any time soon now, so
* it's OK to leave it out of version control.
*/
+EXPORT_SYMBOL(strcpy);
EXPORT_SYMBOL(memcpy);
EXPORT_SYMBOL(memset);
EXPORT_SYMBOL(memcmp);
#include <asm/cacheflush.h>
#include <asm/blackfin.h>
+#include <asm/cplb.h>
#include <asm/cplbinit.h>
-#if defined(CONFIG_BLKFIN_CACHE)
+#if defined(CONFIG_BFIN_ICACHE)
void bfin_icache_init(void)
{
unsigned long *table = icplb_table;
}
#endif
-#if defined(CONFIG_BLKFIN_DCACHE)
+#if defined(CONFIG_BFIN_DCACHE)
void bfin_dcache_init(void)
{
unsigned long *table = dcplb_table;
#include <linux/module.h>
#include <asm/blackfin.h>
+#include <asm/cplb.h>
#include <asm/cplbinit.h>
u_long icplb_table[MAX_CPLBS+1];
struct cplb_tab switch_d;
};
-#if defined(CONFIG_BLKFIN_DCACHE) || defined(CONFIG_BLKFIN_CACHE)
+#if defined(CONFIG_BFIN_DCACHE) || defined(CONFIG_BFIN_ICACHE)
static struct cplb_desc cplb_data[] = {
{
.start = 0,
cplb_data[i].psize,
cplb_data[i].i_conf);
} else {
-#if (defined(CONFIG_BLKFIN_CACHE) && defined(ANOMALY_05000263))
- if (i == SDRAM_KERN) {
+#if defined(CONFIG_BFIN_ICACHE)
+ if (ANOMALY_05000263 && i == SDRAM_KERN) {
fill_cplbtab(t,
cplb_data[i].start,
cplb_data[i].end,
--- /dev/null
+/*
+ * File: arch/blackfin/kernel/early_printk.c
+ * Based on: arch/x86_64/kernel/early_printk.c
+ * Author: Robin Getz <rgetz@blackfin.uclinux.org
+ *
+ * Created: 14Aug2007
+ * Description: allow a console to be used for early printk
+ *
+ * Modified:
+ * Copyright 2004-2007 Analog Devices Inc.
+ *
+ * Bugs: Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/serial_core.h>
+#include <linux/console.h>
+#include <linux/string.h>
+#include <asm/blackfin.h>
+#include <asm/irq_handler.h>
+#include <asm/early_printk.h>
+
+#ifdef CONFIG_SERIAL_BFIN
+extern struct console *bfin_earlyserial_init(unsigned int port,
+ unsigned int cflag);
+#endif
+
+static struct console *early_console;
+
+/* Default console */
+#define DEFAULT_PORT 0
+#define DEFAULT_CFLAG CS8|B57600
+
+/* Default console for early crashes */
+#define DEFAULT_EARLY_PORT "serial,uart0,57600"
+
+#ifdef CONFIG_SERIAL_CORE
+/* What should get here is "0,57600" */
+static struct console * __init earlyserial_init(char *buf)
+{
+ int baud, bit;
+ char parity;
+ unsigned int serial_port = DEFAULT_PORT;
+ unsigned int cflag = DEFAULT_CFLAG;
+
+ serial_port = simple_strtoul(buf, &buf, 10);
+ buf++;
+
+ cflag = 0;
+ baud = simple_strtoul(buf, &buf, 10);
+ switch (baud) {
+ case 1200:
+ cflag |= B1200;
+ break;
+ case 2400:
+ cflag |= B2400;
+ break;
+ case 4800:
+ cflag |= B4800;
+ break;
+ case 9600:
+ cflag |= B9600;
+ break;
+ case 19200:
+ cflag |= B19200;
+ break;
+ case 38400:
+ cflag |= B38400;
+ break;
+ case 115200:
+ cflag |= B115200;
+ break;
+ default:
+ cflag |= B57600;
+ }
+
+ parity = buf[0];
+ buf++;
+ switch (parity) {
+ case 'e':
+ cflag |= PARENB;
+ break;
+ case 'o':
+ cflag |= PARODD;
+ break;
+ }
+
+ bit = simple_strtoul(buf, &buf, 10);
+ switch (bit) {
+ case 5:
+ cflag |= CS5;
+ break;
+ case 6:
+ cflag |= CS5;
+ break;
+ case 7:
+ cflag |= CS5;
+ break;
+ default:
+ cflag |= CS8;
+ }
+
+#ifdef CONFIG_SERIAL_BFIN
+ return bfin_earlyserial_init(serial_port, cflag);
+#else
+ return NULL;
+#endif
+
+}
+#endif
+
+int __init setup_early_printk(char *buf)
+{
+
+ /* Crashing in here would be really bad, so check both the var
+ and the pointer before we start using it
+ */
+ if (!buf)
+ return 0;
+
+ if (!*buf)
+ return 0;
+
+ if (early_console != NULL)
+ return 0;
+
+#ifdef CONFIG_SERIAL_BFIN
+ /* Check for Blackfin Serial */
+ if (!strncmp(buf, "serial,uart", 11)) {
+ buf += 11;
+ early_console = earlyserial_init(buf);
+ }
+#endif
+#ifdef CONFIG_FB
+ /* TODO: add framebuffer console support */
+#endif
+
+ if (likely(early_console)) {
+ early_console->flags |= CON_BOOT;
+
+ register_console(early_console);
+ printk(KERN_INFO "early printk enabled on %s%d\n",
+ early_console->name,
+ early_console->index);
+ }
+
+ return 0;
+}
+
+/*
+ * Set up a temporary Event Vector Table, so if something bad happens before
+ * the kernel is fully started, it doesn't vector off into somewhere we don't
+ * know
+ */
+
+asmlinkage void __init init_early_exception_vectors(void)
+{
+ SSYNC();
+
+ /* cannot program in software:
+ * evt0 - emulation (jtag)
+ * evt1 - reset
+ */
+ bfin_write_EVT2(early_trap);
+ bfin_write_EVT3(early_trap);
+ bfin_write_EVT5(early_trap);
+ bfin_write_EVT6(early_trap);
+ bfin_write_EVT7(early_trap);
+ bfin_write_EVT8(early_trap);
+ bfin_write_EVT9(early_trap);
+ bfin_write_EVT10(early_trap);
+ bfin_write_EVT11(early_trap);
+ bfin_write_EVT12(early_trap);
+ bfin_write_EVT13(early_trap);
+ bfin_write_EVT14(early_trap);
+ bfin_write_EVT15(early_trap);
+ CSYNC();
+
+ /* Set all the return from interupt, exception, NMI to a known place
+ * so if we do a RETI, RETX or RETN by mistake - we go somewhere known
+ * Note - don't change RETS - we are in a subroutine, or
+ * RETE - since it might screw up if emulator is attached
+ */
+ asm("\tRETI = %0; RETX = %0; RETN = %0;\n"
+ : : "p"(early_trap));
+
+}
+
+asmlinkage void __init early_trap_c(struct pt_regs *fp, void *retaddr)
+{
+ /* This can happen before the uart is initialized, so initialize
+ * the UART now
+ */
+ if (likely(early_console == NULL))
+ setup_early_printk(DEFAULT_EARLY_PORT);
+
+ dump_bfin_regs(fp, retaddr);
+ dump_bfin_trace_buffer();
+
+ panic("Died early");
+}
+
+early_param("earlyprintk", setup_early_printk);
#include <linux/kallsyms.h>
#include <linux/interrupt.h>
#include <linux/irq.h>
+#include <asm/trace.h>
static unsigned long irq_err_count;
static spinlock_t irq_controller_lock;
*/
#ifdef CONFIG_DO_IRQ_L1
-asmlinkage void asm_do_IRQ(unsigned int irq, struct pt_regs *regs)__attribute__((l1_text));
+__attribute__((l1_text))
#endif
-
asmlinkage void asm_do_IRQ(unsigned int irq, struct pt_regs *regs)
{
struct pt_regs *old_regs;
}
init_arch_irq();
+
+#ifdef CONFIG_DEBUG_BFIN_HWTRACE_EXPAND
+ /* Now that evt_ivhw is set up, turn this on */
+ trace_buff_offset = 0;
+ bfin_write_TBUFCTL(BFIN_TRACE_ON);
+ printk(KERN_INFO "Hardware Trace expanded to %ik\n",
+ 1 << CONFIG_DEBUG_BFIN_HWTRACE_EXPAND_LEN);
+#endif
}
}
}
-void machine_restart(char *__unused)
-{
-#if defined(CONFIG_BLKFIN_CACHE)
- bfin_write_IMEM_CONTROL(0x01);
- SSYNC();
-#endif
- bfin_reset();
- /* Dont do anything till the reset occurs */
- while (1) {
- SSYNC();
- }
-}
-
-void machine_halt(void)
-{
- for (;;)
- asm volatile ("idle");
-}
-
-void machine_power_off(void)
-{
- for (;;)
- asm volatile ("idle");
-}
-
void show_regs(struct pt_regs *regs)
{
printk(KERN_NOTICE "\n");
#if defined(CONFIG_ACCESS_CHECK)
int _access_ok(unsigned long addr, unsigned long size)
{
-
+ if (size == 0)
+ return 1;
if (addr > (addr + size))
return 0;
if (segment_eq(get_fs(), KERNEL_DS))
#include <asm/processor.h>
#include <asm/asm-offsets.h>
#include <asm/dma.h>
+#include <asm/fixed_code.h>
#define MAX_SHARED_LIBS 3
#define TEXT_OFFSET 0
&& start + len <= (unsigned long)sraml->addr + sraml->length)
return 0;
+ if (start >= FIXED_CODE_START && start + len <= FIXED_CODE_END)
+ return 0;
+
return -EIO;
}
copied = sizeof(tmp);
} else
#endif
- copied =
- access_process_vm(child, addr + add, &tmp,
- sizeof(tmp), 0);
+ if (addr + add >= FIXED_CODE_START
+ && addr + add + sizeof(tmp) <= FIXED_CODE_END) {
+ memcpy(&tmp, (const void *)(addr + add), sizeof(tmp));
+ copied = sizeof(tmp);
+ } else
+ copied = access_process_vm(child, addr + add, &tmp,
+ sizeof(tmp), 0);
pr_debug("ptrace: copied size %d [0x%08lx]\n", copied, tmp);
if (copied != sizeof(tmp))
break;
copied = sizeof(data);
} else
#endif
- copied =
- access_process_vm(child, addr + add, &data,
- sizeof(data), 1);
+ if (addr + add >= FIXED_CODE_START
+ && addr + add + sizeof(data) <= FIXED_CODE_END) {
+ memcpy((void *)(addr + add), &data, sizeof(data));
+ copied = sizeof(data);
+ } else
+ copied = access_process_vm(child, addr + add, &data,
+ sizeof(data), 1);
pr_debug("ptrace: copied size %d\n", copied);
if (copied != sizeof(data))
break;
--- /dev/null
+/*
+ * arch/blackfin/kernel/reboot.c - handle shutdown/reboot
+ *
+ * Copyright 2004-2007 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#include <linux/interrupt.h>
+#include <asm/bfin-global.h>
+#include <asm/reboot.h>
+#include <asm/system.h>
+
+#if defined(BF537_FAMILY) || defined(BF533_FAMILY)
+#define SYSCR_VAL 0x0
+#elif defined(BF561_FAMILY)
+#define SYSCR_VAL 0x20
+#elif defined(BF548_FAMILY)
+#define SYSCR_VAL 0x10
+#endif
+
+/* A system soft reset makes external memory unusable
+ * so force this function into L1.
+ */
+__attribute__((l1_text))
+void bfin_reset(void)
+{
+ /* force BMODE and disable Core B (as needed) */
+ bfin_write_SYSCR(SYSCR_VAL);
+
+ /* we use asm ssync here because it's save and we save some L1 */
+ asm("ssync;");
+
+ while (1) {
+ /* initiate system soft reset with magic 0x7 */
+ bfin_write_SWRST(0x7);
+ asm("ssync;");
+ /* clear system soft reset */
+ bfin_write_SWRST(0);
+ asm("ssync;");
+ /* issue core reset */
+ asm("raise 1");
+ }
+}
+
+__attribute__((weak))
+void native_machine_restart(char *cmd)
+{
+}
+
+void machine_restart(char *cmd)
+{
+ native_machine_restart(cmd);
+ local_irq_disable();
+ bfin_reset();
+}
+
+__attribute__((weak))
+void native_machine_halt(void)
+{
+ idle_with_irq_disabled();
+}
+
+void machine_halt(void)
+{
+ native_machine_halt();
+}
+
+__attribute__((weak))
+void native_machine_power_off(void)
+{
+ idle_with_irq_disabled();
+}
+
+void machine_power_off(void)
+{
+ native_machine_power_off();
+}
#include <linux/cramfs_fs.h>
#include <linux/romfs_fs.h>
+#include <asm/cplb.h>
#include <asm/cacheflush.h>
#include <asm/blackfin.h>
#include <asm/cplbinit.h>
#include <asm/fixed_code.h>
+#include <asm/early_printk.h>
u16 _bfin_swrst;
void __init bf53x_cache_init(void)
{
-#if defined(CONFIG_BLKFIN_DCACHE) || defined(CONFIG_BLKFIN_CACHE)
+#if defined(CONFIG_BFIN_DCACHE) || defined(CONFIG_BFIN_ICACHE)
generate_cpl_tables();
#endif
-#ifdef CONFIG_BLKFIN_CACHE
+#ifdef CONFIG_BFIN_ICACHE
bfin_icache_init();
printk(KERN_INFO "Instruction Cache Enabled\n");
#endif
-#ifdef CONFIG_BLKFIN_DCACHE
+#ifdef CONFIG_BFIN_DCACHE
bfin_dcache_init();
printk(KERN_INFO "Data Cache Enabled"
-# if defined CONFIG_BLKFIN_WB
+# if defined CONFIG_BFIN_WB
" (write-back)"
-# elif defined CONFIG_BLKFIN_WT
+# elif defined CONFIG_BFIN_WT
" (write-through)"
# endif
"\n");
1;
}
}
+ } else if (!memcmp(to, "earlyprintk=", 12)) {
+ to += 12;
+ setup_early_printk(to);
}
-
}
c = *(to++);
if (!c)
#ifdef CONFIG_DUMMY_CONSOLE
conswitchp = &dummy_con;
#endif
+
+#if defined(CONFIG_CMDLINE_BOOL)
+ strncpy(&command_line[0], CONFIG_CMDLINE, sizeof(command_line));
+ command_line[sizeof(command_line) - 1] = 0;
+#endif
+
+ /* Keep a copy of command line */
+ *cmdline_p = &command_line[0];
+ memcpy(boot_command_line, command_line, COMMAND_LINE_SIZE);
+ boot_command_line[COMMAND_LINE_SIZE - 1] = '\0';
+
+ /* setup memory defaults from the user config */
+ physical_mem_end = 0;
+ _ramend = CONFIG_MEM_SIZE * 1024 * 1024;
+
+ parse_cmdline_early(&command_line[0]);
+
cclk = get_cclk();
sclk = get_sclk();
-#if !defined(CONFIG_BFIN_KERNEL_CLOCK) && defined(ANOMALY_05000273)
- if (cclk == sclk)
+#if !defined(CONFIG_BFIN_KERNEL_CLOCK)
+ if (ANOMALY_05000273 && cclk == sclk)
panic("ANOMALY 05000273, SCLK can not be same as CCLK");
#endif
-#if defined(ANOMALY_05000266)
- bfin_read_IMDMA_D0_IRQ_STATUS();
- bfin_read_IMDMA_D1_IRQ_STATUS();
-#endif
-
-#ifdef DEBUG_SERIAL_EARLY_INIT
- bfin_console_init(); /* early console registration */
- /* this give a chance to get printk() working before crash. */
+#ifdef BF561_FAMILY
+ if (ANOMALY_05000266) {
+ bfin_read_IMDMA_D0_IRQ_STATUS();
+ bfin_read_IMDMA_D1_IRQ_STATUS();
+ }
#endif
printk(KERN_INFO "Hardware Trace ");
flash_probe();
#endif
-#if defined(CONFIG_CMDLINE_BOOL)
- strncpy(&command_line[0], CONFIG_CMDLINE, sizeof(command_line));
- command_line[sizeof(command_line) - 1] = 0;
-#endif
-
- /* Keep a copy of command line */
- *cmdline_p = &command_line[0];
- memcpy(boot_command_line, command_line, COMMAND_LINE_SIZE);
- boot_command_line[COMMAND_LINE_SIZE - 1] = '\0';
-
- /* setup memory defaults from the user config */
- physical_mem_end = 0;
- _ramend = CONFIG_MEM_SIZE * 1024 * 1024;
-
- parse_cmdline_early(&command_line[0]);
-
if (physical_mem_end == 0)
physical_mem_end = _ramend;
&& ((unsigned long *)mtd_phys)[1] == ROMSB_WORD1)
mtd_size =
PAGE_ALIGN(be32_to_cpu(((unsigned long *)mtd_phys)[2]));
-# if (defined(CONFIG_BLKFIN_CACHE) && defined(ANOMALY_05000263))
+# if (defined(CONFIG_BFIN_ICACHE) && ANOMALY_05000263)
/* Due to a Hardware Anomaly we need to limit the size of usable
* instruction memory to max 60MB, 56 if HUNT_FOR_ZERO is on
* 05000263 - Hardware loop corrupted when taking an ICPLB exception
_ebss = memory_mtd_start; /* define _ebss for compatible */
#endif /* CONFIG_MTD_UCLINUX */
-#if (defined(CONFIG_BLKFIN_CACHE) && defined(ANOMALY_05000263))
+#if (defined(CONFIG_BFIN_ICACHE) && ANOMALY_05000263)
/* Due to a Hardware Anomaly we need to limit the size of usable
* instruction memory to max 60MB, 56 if HUNT_FOR_ZERO is on
* 05000263 - Hardware loop corrupted when taking an ICPLB exception
CPU, bfin_revid());
printk(KERN_INFO "Blackfin Linux support by http://blackfin.uclinux.org/\n");
- printk(KERN_INFO "Processor Speed: %lu MHz core clock and %lu Mhz System Clock\n",
+ printk(KERN_INFO "Processor Speed: %lu MHz core clock and %lu MHz System Clock\n",
cclk / 1000000, sclk / 1000000);
-#if defined(ANOMALY_05000273)
- if ((cclk >> 1) <= sclk)
+ if (ANOMALY_05000273 && (cclk >> 1) <= sclk)
printk("\n\n\nANOMALY_05000273: CCLK must be >= 2*SCLK !!!\n\n\n");
-#endif
printk(KERN_INFO "Board Memory: %ldMB\n", physical_mem_end >> 20);
printk(KERN_INFO "Kernel Managed Memory: %ldMB\n", _ramend >> 20);
seq_printf(m, "I-CACHE:\tOFF\n");
if ((bfin_read_DMEM_CONTROL()) & (ENDCPLB | DMC_ENABLE))
seq_printf(m, "D-CACHE:\tON"
-#if defined CONFIG_BLKFIN_WB
+#if defined CONFIG_BFIN_WB
" (write-back)"
-#elif defined CONFIG_BLKFIN_WT
+#elif defined CONFIG_BFIN_WT
" (write-through)"
#endif
"\n");
}
- seq_printf(m, "I-CACHE Size:\t%dKB\n", BLKFIN_ICACHESIZE / 1024);
+ seq_printf(m, "I-CACHE Size:\t%dKB\n", BFIN_ICACHESIZE / 1024);
seq_printf(m, "D-CACHE Size:\t%dKB\n", dcache_size);
seq_printf(m, "I-CACHE Setup:\t%d Sub-banks/%d Ways, %d Lines/Way\n",
- BLKFIN_ISUBBANKS, BLKFIN_IWAYS, BLKFIN_ILINES);
+ BFIN_ISUBBANKS, BFIN_IWAYS, BFIN_ILINES);
seq_printf(m,
"D-CACHE Setup:\t%d Super-banks/%d Sub-banks/%d Ways, %d Lines/Way\n",
- dsup_banks, BLKFIN_DSUBBANKS, BLKFIN_DWAYS,
- BLKFIN_DLINES);
-#ifdef CONFIG_BLKFIN_CACHE_LOCK
+ dsup_banks, BFIN_DSUBBANKS, BFIN_DWAYS,
+ BFIN_DLINES);
+#ifdef CONFIG_BFIN_ICACHE_LOCK
switch (read_iloc()) {
case WAY0_L:
seq_printf(m, "Way0 Locked-Down\n");
CSYNC();
}
-asmlinkage void trap_c(struct pt_regs *fp);
-
int kstack_depth_to_print = 48;
+#ifdef CONFIG_DEBUG_BFIN_HWTRACE_ON
static int printk_address(unsigned long address)
{
struct vm_list_struct *vml;
/* we were unable to find this address anywhere */
return printk("[<0x%p>]", (void *)address);
}
+#endif
+
+asmlinkage void double_fault_c(struct pt_regs *fp)
+{
+ printk(KERN_EMERG "\n" KERN_EMERG "Double Fault\n");
+ dump_bfin_regs(fp, (void *)fp->retx);
+ panic("Double Fault - unrecoverable event\n");
+
+}
asmlinkage void trap_c(struct pt_regs *fp)
{
- int j, sig = 0;
+#ifdef CONFIG_DEBUG_BFIN_HWTRACE_ON
+ int j;
+#endif
+ int sig = 0;
siginfo_t info;
unsigned long trapnr = fp->seqstat & SEQSTAT_EXCAUSE;
break;
}
- info.si_signo = sig;
- info.si_errno = 0;
- info.si_addr = (void *)fp->pc;
- force_sig_info(sig, &info, current);
if (sig != 0 && sig != SIGTRAP) {
unsigned long stack;
dump_bfin_regs(fp, (void *)fp->retx);
if (current->mm == NULL)
panic("Kernel exception");
}
+ info.si_signo = sig;
+ info.si_errno = 0;
+ info.si_addr = (void *)fp->pc;
+ force_sig_info(sig, &info, current);
/* if the address that we are about to return to is not valid, set it
* to a valid address, if we have a current application or panic
/* Typical exception handling routines */
+#define EXPAND_LEN ((1 << CONFIG_DEBUG_BFIN_HWTRACE_EXPAND_LEN) * 256 - 1)
+
void dump_bfin_trace_buffer(void)
{
- int tflags;
+#ifdef CONFIG_DEBUG_BFIN_HWTRACE_ON
+ int tflags, i = 0;
+#ifdef CONFIG_DEBUG_BFIN_HWTRACE_EXPAND
+ int j, index;
+#endif
+
trace_buffer_save(tflags);
+ printk(KERN_EMERG "Hardware Trace:\n");
+
if (likely(bfin_read_TBUFSTAT() & TBUFCNT)) {
- int i;
- printk(KERN_EMERG "Hardware Trace:\n");
- for (i = 0; bfin_read_TBUFSTAT() & TBUFCNT; i++) {
- printk(KERN_EMERG "%2i Target : ", i);
+ for (; bfin_read_TBUFSTAT() & TBUFCNT; i++) {
+ printk(KERN_EMERG "%4i Target : ", i);
printk_address((unsigned long)bfin_read_TBUF());
- printk("\n" KERN_EMERG " Source : ");
+ printk("\n" KERN_EMERG " Source : ");
printk_address((unsigned long)bfin_read_TBUF());
printk("\n");
}
}
+#ifdef CONFIG_DEBUG_BFIN_HWTRACE_EXPAND
+ if (trace_buff_offset)
+ index = trace_buff_offset/4 - 1;
+ else
+ index = EXPAND_LEN;
+
+ j = (1 << CONFIG_DEBUG_BFIN_HWTRACE_EXPAND_LEN) * 128;
+ while (j) {
+ printk(KERN_EMERG "%4i Target : ", i);
+ printk_address(software_trace_buff[index]);
+ index -= 1;
+ if (index < 0 )
+ index = EXPAND_LEN;
+ printk("\n" KERN_EMERG " Source : ");
+ printk_address(software_trace_buff[index]);
+ index -= 1;
+ if (index < 0)
+ index = EXPAND_LEN;
+ printk("\n");
+ j--;
+ i++;
+ }
+#endif
+
trace_buffer_restore(tflags);
+#endif
}
EXPORT_SYMBOL(dump_bfin_trace_buffer);
void dump_stack(void)
{
unsigned long stack;
+#ifdef CONFIG_DEBUG_BFIN_HWTRACE_ON
int tflags;
+#endif
trace_buffer_save(tflags);
dump_bfin_trace_buffer();
show_stack(current, &stack);
unsigned short x = 0;
for (; i < ((unsigned int)retaddr & 0xFFFFFFF0) + 32; i += 2) {
if (!(i & 0xF))
- printk(KERN_EMERG "\n" KERN_EMERG
- "0x%08x: ", i);
+ printk("\n" KERN_EMERG "0x%08x: ", i);
if (get_user(x, (unsigned short *)i))
break;
return ret;
}
+int bfin_request_exception(unsigned int exception, void (*handler)(void))
+{
+ void (*curr_handler)(void);
+
+ if (exception > 0x3F)
+ return -EINVAL;
+
+ curr_handler = ex_table[exception];
+
+ if (curr_handler != ex_replaceable)
+ return -EBUSY;
+
+ ex_table[exception] = handler;
+
+ return 0;
+}
+EXPORT_SYMBOL(bfin_request_exception);
+
+int bfin_free_exception(unsigned int exception, void (*handler)(void))
+{
+ void (*curr_handler)(void);
+
+ if (exception > 0x3F)
+ return -EINVAL;
+
+ curr_handler = ex_table[exception];
+
+ if (curr_handler != handler)
+ return -EBUSY;
+
+ ex_table[exception] = ex_replaceable;
+
+ return 0;
+}
+EXPORT_SYMBOL(bfin_free_exception);
+
void panic_cplb_error(int cplb_panic, struct pt_regs *fp)
{
switch (cplb_panic) {
TEXT_TEXT
SCHED_TEXT
LOCK_TEXT
- *(.text.lock)
+ KPROBES_TEXT
+ *(.text.*)
*(.fixup)
. = ALIGN(16);
__etext = .;
}
- RODATA
+ RO_DATA(PAGE_SIZE)
.data :
{
__sdata = .;
. = ALIGN(THREAD_SIZE);
*(.data.init_task)
- DATA_DATA
- CONSTRUCTORS
. = ALIGN(32);
*(.data.cacheline_aligned)
+ DATA_DATA
+ *(.data.*)
+ CONSTRUCTORS
+
. = ALIGN(THREAD_SIZE);
__edata = .;
}
___init_begin = .;
- .init :
+
+ .init.text :
{
. = ALIGN(PAGE_SIZE);
__sinittext = .;
*(.init.text)
__einittext = .;
+ }
+ .init.data :
+ {
+ . = ALIGN(16);
*(.init.data)
+ }
+ .init.setup :
+ {
. = ALIGN(16);
___setup_start = .;
*(.init.setup)
___setup_end = .;
- ___start___param = .;
- *(__param)
- ___stop___param = .;
+ }
+ .initcall.init :
+ {
___initcall_start = .;
INITCALLS
___initcall_end = .;
+ }
+ .con_initcall.init :
+ {
___con_initcall_start = .;
*(.con_initcall.init)
___con_initcall_end = .;
- ___security_initcall_start = .;
- *(.security_initcall.init)
- ___security_initcall_end = .;
+ }
+ SECURITY_INIT
+ .init.ramfs :
+ {
. = ALIGN(4);
___initramfs_start = .;
*(.init.ramfs)
___initramfs_end = .;
- . = ALIGN(4);
}
__l1_lma_start = .;
- .text_l1 L1_CODE_START : AT(LOADADDR(.init) + SIZEOF(.init))
+ .text_l1 L1_CODE_START : AT(LOADADDR(.init.ramfs) + SIZEOF(.init.ramfs))
{
. = ALIGN(4);
__stext_l1 = .;
{
. = ALIGN(4);
___bss_start = .;
- *(.bss)
+ *(.bss .bss.*)
*(COMMON)
. = ALIGN(4);
___bss_stop = .;
__end = .;
}
+ STABS_DEBUG
+
+ DWARF_DEBUG
+
+ NOTES
+
/DISCARD/ :
{
*(.exit.text)
LSETUP (.Lquad_loop_s, .Lquad_loop_e) LC0=P1;
.Lquad_loop_s:
-#ifdef ANOMALY_05000202
+#if ANOMALY_05000202
R0 = [P0++];
R1 = [I0++];
#else
R0 = R1;
I1 = P1;
R3 = [I1++];
-#ifdef ANOMALY_05000202
+#if ANOMALY_05000202
.Lword_loops:
[P0++] = R3;
.Lword_loope:
R1 = [I0++];
LSETUP (.Lquad_loops, .Lquad_loope) LC0=P1;
-#ifdef ANOMALY_05000202
+#if ANOMALY_05000202
.Lquad_loops:
[P0++] = R1;
.Lquad_loope:
R1 = B[P3--] (Z);
CC = P2 == 0;
IF CC JUMP .Lno_loop;
-#ifdef ANOMALY_05000245
+#if ANOMALY_05000245
NOP;
NOP;
#endif
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
#include <linux/usb_isp1362.h>
+#include <linux/pata_platform.h>
#include <linux/irq.h>
+#include <asm/dma.h>
#include <asm/bfin5xx_spi.h>
/*
/* the modalias must be the same as spi device driver name */
.modalias = "m25p80", /* Name of spi_driver for this device */
.max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1, /* Framework bus number */
+ .bus_num = 0, /* Framework bus number */
.chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/
.platform_data = &bfin_spi_flash_data,
.controller_data = &spi_flash_chip_info,
}, {
.modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
.max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1, /* Framework bus number */
+ .bus_num = 0, /* Framework bus number */
.chip_select = 2, /* Framework chip select. */
.platform_data = NULL, /* No spi_driver specific config */
.controller_data = &spi_adc_chip_info,
{
.modalias = "ad1836-spi",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1,
+ .bus_num = 0,
.chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
.controller_data = &ad1836_spi_chip_info,
},
#endif
};
+/* SPI (0) */
+static struct resource bfin_spi0_resource[] = {
+ [0] = {
+ .start = SPI0_REGBASE,
+ .end = SPI0_REGBASE + 0xFF,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = CH_SPI,
+ .end = CH_SPI,
+ .flags = IORESOURCE_IRQ,
+ }
+};
+
/* SPI controller data */
-static struct bfin5xx_spi_master spi_bfin_master_info = {
+static struct bfin5xx_spi_master bfin_spi0_info = {
.num_chipselect = 8,
.enable_dma = 1, /* master has the ability to do dma transfer */
};
-static struct platform_device spi_bfin_master_device = {
- .name = "bfin-spi-master",
- .id = 1, /* Bus number */
+static struct platform_device bfin_spi0_device = {
+ .name = "bfin-spi",
+ .id = 0, /* Bus number */
+ .num_resources = ARRAY_SIZE(bfin_spi0_resource),
+ .resource = bfin_spi0_resource,
.dev = {
- .platform_data = &spi_bfin_master_info, /* Passed to driver */
+ .platform_data = &bfin_spi0_info, /* Passed to driver */
},
};
#endif /* spi master and devices */
};
#endif
+#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+#define PATA_INT 38
+
+static struct pata_platform_info bfin_pata_platform_data = {
+ .ioport_shift = 2,
+ .irq_type = IRQF_TRIGGER_HIGH | IRQF_DISABLED,
+};
+
+static struct resource bfin_pata_resources[] = {
+ {
+ .start = 0x2030C000,
+ .end = 0x2030C01F,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = 0x2030D018,
+ .end = 0x2030D01B,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = PATA_INT,
+ .end = PATA_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device bfin_pata_device = {
+ .name = "pata_platform",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(bfin_pata_resources),
+ .resource = bfin_pata_resources,
+ .dev = {
+ .platform_data = &bfin_pata_platform_data,
+ }
+};
+#endif
+
static struct platform_device *cm_bf533_devices[] __initdata = {
#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
&bfin_uart_device,
#endif
#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
- &spi_bfin_master_device,
+ &bfin_spi0_device,
+#endif
+
+#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+ &bfin_pata_device,
#endif
};
#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
#endif
+
+#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+ irq_desc[PATA_INT].status |= IRQ_NOAUTOEN;
+#endif
return 0;
}
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
#include <linux/usb_isp1362.h>
+#include <linux/pata_platform.h>
#include <linux/irq.h>
+#include <asm/dma.h>
#include <asm/bfin5xx_spi.h>
/*
};
#endif
+#if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE)
+static struct platform_device bfin_fb_adv7393_device = {
+ .name = "bfin-adv7393",
+};
+#endif
+
/*
* USB-LAN EzExtender board
* Driver needs to know address, irq and flag pin.
/* the modalias must be the same as spi device driver name */
.modalias = "m25p80", /* Name of spi_driver for this device */
.max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1, /* Framework bus number */
+ .bus_num = 0, /* Framework bus number */
.chip_select = 2, /* Framework chip select. On STAMP537 it is SPISSEL2*/
.platform_data = &bfin_spi_flash_data,
.controller_data = &spi_flash_chip_info,
{
.modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
.max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1, /* Framework bus number */
+ .bus_num = 0, /* Framework bus number */
.chip_select = 1, /* Framework chip select. */
.platform_data = NULL, /* No spi_driver specific config */
.controller_data = &spi_adc_chip_info,
{
.modalias = "ad1836-spi",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1,
+ .bus_num = 0,
.chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
.controller_data = &ad1836_spi_chip_info,
},
#endif
};
+/* SPI (0) */
+static struct resource bfin_spi0_resource[] = {
+ [0] = {
+ .start = SPI0_REGBASE,
+ .end = SPI0_REGBASE + 0xFF,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = CH_SPI,
+ .end = CH_SPI,
+ .flags = IORESOURCE_IRQ,
+ }
+};
+
/* SPI controller data */
-static struct bfin5xx_spi_master spi_bfin_master_info = {
+static struct bfin5xx_spi_master bfin_spi0_info = {
.num_chipselect = 8,
.enable_dma = 1, /* master has the ability to do dma transfer */
};
-static struct platform_device spi_bfin_master_device = {
- .name = "bfin-spi-master",
- .id = 1, /* Bus number */
+static struct platform_device bfin_spi0_device = {
+ .name = "bfin-spi",
+ .id = 0, /* Bus number */
+ .num_resources = ARRAY_SIZE(bfin_spi0_resource),
+ .resource = bfin_spi0_resource,
.dev = {
- .platform_data = &spi_bfin_master_info, /* Passed to driver */
+ .platform_data = &bfin_spi0_info, /* Passed to driver */
},
};
#endif /* spi master and devices */
};
#endif
+#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+#define PATA_INT 55
+
+static struct pata_platform_info bfin_pata_platform_data = {
+ .ioport_shift = 1,
+ .irq_type = IRQF_TRIGGER_HIGH | IRQF_DISABLED,
+};
+
+static struct resource bfin_pata_resources[] = {
+ {
+ .start = 0x20314020,
+ .end = 0x2031403F,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = 0x2031401C,
+ .end = 0x2031401F,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = PATA_INT,
+ .end = PATA_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device bfin_pata_device = {
+ .name = "pata_platform",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(bfin_pata_resources),
+ .resource = bfin_pata_resources,
+ .dev = {
+ .platform_data = &bfin_pata_platform_data,
+ }
+};
+#endif
+
static struct platform_device *ezkit_devices[] __initdata = {
#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
&smc91x_device,
#endif
#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
- &spi_bfin_master_device,
+ &bfin_spi0_device,
+#endif
+
+#if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE)
+ &bfin_fb_adv7393_device,
#endif
#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
&bfin_uart_device,
#endif
+
+#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+ &bfin_pata_device,
+#endif
};
static int __init ezkit_init(void)
#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
#endif
+
+#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+ irq_desc[PATA_INT].status |= IRQ_NOAUTOEN;
+#endif
return 0;
}
#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
#include <linux/usb_isp1362.h>
#endif
+#include <linux/pata_platform.h>
#include <linux/irq.h>
+#include <asm/dma.h>
#include <asm/bfin5xx_spi.h>
+#include <asm/reboot.h>
/*
* Name the Board for the /proc/cpuinfo
};
#endif
+#if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE)
+static struct platform_device bfin_fb_adv7393_device = {
+ .name = "bfin-adv7393",
+};
+#endif
+
#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
static struct resource net2272_bfin_resources[] = {
{
/* the modalias must be the same as spi device driver name */
.modalias = "m25p80", /* Name of spi_driver for this device */
.max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1, /* Framework bus number */
+ .bus_num = 0, /* Framework bus number */
.chip_select = 2, /* Framework chip select. On STAMP537 it is SPISSEL2*/
.platform_data = &bfin_spi_flash_data,
.controller_data = &spi_flash_chip_info,
{
.modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
.max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1, /* Framework bus number */
+ .bus_num = 0, /* Framework bus number */
.chip_select = 1, /* Framework chip select. */
.platform_data = NULL, /* No spi_driver specific config */
.controller_data = &spi_adc_chip_info,
{
.modalias = "ad1836-spi",
.max_speed_hz = 31250000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1,
+ .bus_num = 0,
.chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
.controller_data = &ad1836_spi_chip_info,
},
{
.modalias = "spi_mmc_dummy",
.max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1,
+ .bus_num = 0,
.chip_select = 0,
.platform_data = NULL,
.controller_data = &spi_mmc_chip_info,
{
.modalias = "spi_mmc",
.max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1,
+ .bus_num = 0,
.chip_select = CONFIG_SPI_MMC_CS_CHAN,
.platform_data = NULL,
.controller_data = &spi_mmc_chip_info,
{
.modalias = "fxs-spi",
.max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1,
- .chip_select = 3,
+ .bus_num = 0,
+ .chip_select = 8 - CONFIG_J11_JUMPER,
.controller_data = &spi_si3xxx_chip_info,
.mode = SPI_MODE_3,
},
{
.modalias = "fxo-spi",
.max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1,
- .chip_select = 2,
+ .bus_num = 0,
+ .chip_select = 8 - CONFIG_J19_JUMPER,
.controller_data = &spi_si3xxx_chip_info,
.mode = SPI_MODE_3,
},
{
.modalias = "ad5304_spi",
.max_speed_hz = 1000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1,
+ .bus_num = 0,
.chip_select = 2,
.platform_data = NULL,
.controller_data = &ad5304_chip_info,
#endif
};
+/* SPI (0) */
+static struct resource bfin_spi0_resource[] = {
+ [0] = {
+ .start = SPI0_REGBASE,
+ .end = SPI0_REGBASE + 0xFF,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = CH_SPI,
+ .end = CH_SPI,
+ .flags = IORESOURCE_IRQ,
+ }
+};
+
/* SPI controller data */
-static struct bfin5xx_spi_master spi_bfin_master_info = {
+static struct bfin5xx_spi_master bfin_spi0_info = {
.num_chipselect = 8,
.enable_dma = 1, /* master has the ability to do dma transfer */
};
-static struct platform_device spi_bfin_master_device = {
- .name = "bfin-spi-master",
- .id = 1, /* Bus number */
+static struct platform_device bfin_spi0_device = {
+ .name = "bfin-spi",
+ .id = 0, /* Bus number */
+ .num_resources = ARRAY_SIZE(bfin_spi0_resource),
+ .resource = bfin_spi0_resource,
.dev = {
- .platform_data = &spi_bfin_master_info, /* Passed to driver */
+ .platform_data = &bfin_spi0_info, /* Passed to driver */
},
};
#endif /* spi master and devices */
};
#endif
+#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+#define PATA_INT 55
+
+static struct pata_platform_info bfin_pata_platform_data = {
+ .ioport_shift = 1,
+ .irq_type = IRQF_TRIGGER_HIGH | IRQF_DISABLED,
+};
+
+static struct resource bfin_pata_resources[] = {
+ {
+ .start = 0x20314020,
+ .end = 0x2031403F,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = 0x2031401C,
+ .end = 0x2031401F,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = PATA_INT,
+ .end = PATA_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device bfin_pata_device = {
+ .name = "pata_platform",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(bfin_pata_resources),
+ .resource = bfin_pata_resources,
+ .dev = {
+ .platform_data = &bfin_pata_platform_data,
+ }
+};
+#endif
+
static struct platform_device *stamp_devices[] __initdata = {
#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
&rtc_device,
&smc91x_device,
#endif
+#if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE)
+ &bfin_fb_adv7393_device,
+#endif
+
#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
&net2272_bfin_device,
#endif
#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
- &spi_bfin_master_device,
+ &bfin_spi0_device,
#endif
#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
&bfin_sport0_uart_device,
&bfin_sport1_uart_device,
#endif
+
+#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+ &bfin_pata_device,
+#endif
};
static int __init stamp_init(void)
#endif
#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
- return spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
+ spi_register_board_info(bfin_spi_board_info,
+ ARRAY_SIZE(bfin_spi_board_info));
+#endif
+#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+ irq_desc[PATA_INT].status |= IRQ_NOAUTOEN;
#endif
+ return 0;
}
arch_initcall(stamp_init);
+
+void native_machine_restart(char *cmd)
+{
+#if defined(CONFIG_BFIN_SHARED_FLASH_ENET)
+# define BIT_TO_SET (1 << CONFIG_ENET_FLASH_PIN)
+ bfin_write_FIO_INEN(~BIT_TO_SET);
+ bfin_write_FIO_DIR(BIT_TO_SET);
+ bfin_write_FIO_FLAG_C(BIT_TO_SET);
+#endif
+}
#include <asm/blackfin.h>
#include <asm/trace.h>
#if CONFIG_BFIN_KERNEL_CLOCK
+#include <asm/mach-common/clocks.h>
#include <asm/mach/mem_init.h>
#endif
-#if CONFIG_DEBUG_KERNEL_START
-#include <asm/mach-common/def_LPBlackfin.h>
-#endif
.global __rambase
.global __ramstart
ENTRY(__start)
/* R0: argument of command line string, passed from uboot, save it */
R7 = R0;
- /* Set the SYSCFG register:
- * Enable Cycle Counter and Nesting Of Interrupts (3rd Bit)
- */
- R0 = 0x36;
+ /* Enable Cycle Counter and Nesting Of Interrupts */
+#ifdef CONFIG_BFIN_SCRATCH_REG_CYCLES
+ R0 = SYSCFG_SNEN;
+#else
+ R0 = SYSCFG_SNEN | SYSCFG_CCEN;
+#endif
SYSCFG = R0;
R0 = 0;
M2 = r0;
M3 = r0;
- trace_buffer_start(p0,r0);
+ trace_buffer_init(p0,r0);
P0 = R1;
R0 = R1;
-#if CONFIG_DEBUG_KERNEL_START
-
-/*
- * Set up a temporary Event Vector Table, so if something bad happens before
- * the kernel is fully started, it doesn't vector off into the bootloaders
- * table
- */
- P0.l = lo(EVT2);
- P0.h = hi(EVT2);
- P1.l = lo(EVT15);
- P1.h = hi(EVT15);
- P2.l = debug_kernel_start_trap;
- P2.h = debug_kernel_start_trap;
-
- RTS = P2;
- RTI = P2;
- RTX = P2;
- RTN = P2;
- RTE = P2;
-
-.Lfill_temp_vector_table:
- [P0++] = P2; /* Core Event Vector Table */
- CC = P0 == P1;
- if !CC JUMP .Lfill_temp_vector_table
- P0 = r0;
- P1 = r0;
- P2 = r0;
-
-#endif
-
p0.h = hi(FIO_MASKA_C);
p0.l = lo(FIO_MASKA_C);
r0 = 0xFFFF(Z);
ssync;
/* Turn off the icache */
- p0.l = (IMEM_CONTROL & 0xFFFF);
- p0.h = (IMEM_CONTROL >> 16);
+ p0.l = LO(IMEM_CONTROL);
+ p0.h = HI(IMEM_CONTROL);
R1 = [p0];
R0 = ~ENICPLB;
R0 = R0 & R1;
/* Anomaly 05000125 */
-#ifdef ANOMALY_05000125
+#if ANOMALY_05000125
CLI R2;
SSYNC;
#endif
[p0] = R0;
SSYNC;
-#ifdef ANOMALY_05000125
+#if ANOMALY_05000125
STI R2;
#endif
/* Turn off the dcache */
- p0.l = (DMEM_CONTROL & 0xFFFF);
- p0.h = (DMEM_CONTROL >> 16);
+ p0.l = LO(DMEM_CONTROL);
+ p0.h = HI(DMEM_CONTROL);
R1 = [p0];
R0 = ~ENDCPLB;
R0 = R0 & R1;
/* Anomaly 05000125 */
-#ifdef ANOMALY_05000125
+#if ANOMALY_05000125
CLI R2;
SSYNC;
#endif
[p0] = R0;
SSYNC;
-#ifdef ANOMALY_05000125
+#if ANOMALY_05000125
STI R2;
#endif
fp = sp;
usp = sp;
+#ifdef CONFIG_EARLY_PRINTK
+ SP += -12;
+ call _init_early_exception_vectors;
+ SP += 12;
+#endif
+
/* Put The Code for PLL Programming and SDRAM Programming in L1 ISRAM */
call _bf53x_relocate_l1_mem;
#if CONFIG_BFIN_KERNEL_CLOCK
p0.l = .LWAIT_HERE;
p0.h = .LWAIT_HERE;
reti = p0;
-#if defined(ANOMALY_05000281)
+#if ANOMALY_05000281
nop; nop; nop;
#endif
rti;
w[p0] = r0.l;
ssync;
- p0.l = (EBIU_SDBCTL & 0xFFFF);
- p0.h = (EBIU_SDBCTL >> 16); /* SDRAM Memory Bank Control Register */
+ p0.l = LO(EBIU_SDBCTL);
+ p0.h = HI(EBIU_SDBCTL); /* SDRAM Memory Bank Control Register */
r0 = mem_SDBCTL;
w[p0] = r0.l;
ssync;
ENDPROC(_start_dma_code)
#endif /* CONFIG_BFIN_KERNEL_CLOCK */
-ENTRY(_bfin_reset)
- /* No more interrupts to be handled*/
- CLI R6;
- SSYNC;
-
-#if defined(CONFIG_BFIN_SHARED_FLASH_ENET)
- p0.h = hi(FIO_INEN);
- p0.l = lo(FIO_INEN);
- r0.l = ~(1 << CONFIG_ENET_FLASH_PIN);
- w[p0] = r0.l;
-
- p0.h = hi(FIO_DIR);
- p0.l = lo(FIO_DIR);
- r0.l = (1 << CONFIG_ENET_FLASH_PIN);
- w[p0] = r0.l;
-
- p0.h = hi(FIO_FLAG_C);
- p0.l = lo(FIO_FLAG_C);
- r0.l = (1 << CONFIG_ENET_FLASH_PIN);
- w[p0] = r0.l;
-#endif
-
- /* Clear the IMASK register */
- p0.h = hi(IMASK);
- p0.l = lo(IMASK);
- r0 = 0x0;
- [p0] = r0;
-
- /* Clear the ILAT register */
- p0.h = hi(ILAT);
- p0.l = lo(ILAT);
- r0 = [p0];
- [p0] = r0;
- SSYNC;
-
- /* make sure SYSCR is set to use BMODE */
- P0.h = hi(SYSCR);
- P0.l = lo(SYSCR);
- R0.l = 0x0;
- W[P0] = R0.l;
- SSYNC;
-
- /* issue a system soft reset */
- P1.h = hi(SWRST);
- P1.l = lo(SWRST);
- R1.l = 0x0007;
- W[P1] = R1;
- SSYNC;
-
- /* clear system soft reset */
- R0.l = 0x0000;
- W[P0] = R0;
- SSYNC;
-
- /* issue core reset */
- raise 1;
-
- RTS;
-ENDPROC(_bfin_reset)
-
-#if CONFIG_DEBUG_KERNEL_START
-debug_kernel_start_trap:
- /* Set up a temp stack in L1 - SDRAM might not be working */
- P0.L = lo(L1_DATA_A_START + 0x100);
- P0.H = hi(L1_DATA_A_START + 0x100);
- SP = P0;
-
- /* Make sure the Clocks are the way I think they should be */
- r0 = CONFIG_VCO_MULT & 63; /* Load the VCO multiplier */
- r0 = r0 << 9; /* Shift it over, */
- r1 = CLKIN_HALF; /* Do we need to divide CLKIN by 2?*/
- r0 = r1 | r0;
- r1 = PLL_BYPASS; /* Bypass the PLL? */
- r1 = r1 << 8; /* Shift it over */
- r0 = r1 | r0; /* add them all together */
-
- p0.h = hi(PLL_CTL);
- p0.l = lo(PLL_CTL); /* Load the address */
- cli r2; /* Disable interrupts */
- ssync;
- w[p0] = r0.l; /* Set the value */
- idle; /* Wait for the PLL to stablize */
- sti r2; /* Enable interrupts */
-
-.Lcheck_again1:
- p0.h = hi(PLL_STAT);
- p0.l = lo(PLL_STAT);
- R0 = W[P0](Z);
- CC = BITTST(R0,5);
- if ! CC jump .Lcheck_again1;
-
- /* Configure SCLK & CCLK Dividers */
- r0 = (CONFIG_CCLK_ACT_DIV | CONFIG_SCLK_DIV);
- p0.h = hi(PLL_DIV);
- p0.l = lo(PLL_DIV);
- w[p0] = r0.l;
- ssync;
-
- /* Make sure UART is enabled - you can never be sure */
-
-/*
- * Setup for console. Argument comes from the menuconfig
- */
-
-#ifdef CONFIG_BAUD_9600
-#define CONSOLE_BAUD_RATE 9600
-#elif CONFIG_BAUD_19200
-#define CONSOLE_BAUD_RATE 19200
-#elif CONFIG_BAUD_38400
-#define CONSOLE_BAUD_RATE 38400
-#elif CONFIG_BAUD_57600
-#define CONSOLE_BAUD_RATE 57600
-#elif CONFIG_BAUD_115200
-#define CONSOLE_BAUD_RATE 115200
-#endif
-
- p0.h = hi(UART_GCTL);
- p0.l = lo(UART_GCTL);
- r0 = 0x00(Z);
- w[p0] = r0.L; /* To Turn off UART clocks */
- ssync;
-
- p0.h = hi(UART_LCR);
- p0.l = lo(UART_LCR);
- r0 = 0x83(Z);
- w[p0] = r0.L; /* To enable DLL writes */
- ssync;
-
- R1 = (((CONFIG_CLKIN_HZ * CONFIG_VCO_MULT) / CONFIG_SCLK_DIV) / (CONSOLE_BAUD_RATE * 16));
-
- p0.h = hi(UART_DLL);
- p0.l = lo(UART_DLL);
- r0 = 0xFF(Z);
- r0 = R1 & R0;
- w[p0] = r0.L;
- ssync;
-
- p0.h = hi(UART_DLH);
- p0.l = lo(UART_DLH);
- r1 >>= 8 ;
- w[p0] = r1.L;
- ssync;
-
- p0.h = hi(UART_GCTL);
- p0.l = lo(UART_GCTL);
- r0 = 0x0(Z);
- w[p0] = r0.L; /* To enable UART clock */
- ssync;
-
- p0.h = hi(UART_LCR);
- p0.l = lo(UART_LCR);
- r0 = 0x03(Z);
- w[p0] = r0.L; /* To Turn on UART */
- ssync;
-
- p0.h = hi(UART_GCTL);
- p0.l = lo(UART_GCTL);
- r0 = 0x01(Z);
- w[p0] = r0.L; /* To Turn on UART Clocks */
- ssync;
-
- P0.h = hi(UART_THR);
- P0.l = lo(UART_THR);
- P1.h = hi(UART_LSR);
- P1.l = lo(UART_LSR);
-
- R0.L = 'K';
- call .Lwait_char;
- R0.L='e';
- call .Lwait_char;
- R0.L='r';
- call .Lwait_char;
- R0.L='n'
- call .Lwait_char;
- R0.L='e'
- call .Lwait_char;
- R0.L='l';
- call .Lwait_char;
- R0.L=' ';
- call .Lwait_char;
- R0.L='c';
- call .Lwait_char;
- R0.L='r';
- call .Lwait_char;
- R0.L='a';
- call .Lwait_char;
- R0.L='s';
- call .Lwait_char;
- R0.L='h';
- call .Lwait_char;
- R0.L='\r';
- call .Lwait_char;
- R0.L='\n';
- call .Lwait_char;
-
- R0.L='S';
- call .Lwait_char;
- R0.L='E';
- call .Lwait_char;
- R0.L='Q'
- call .Lwait_char;
- R0.L='S'
- call .Lwait_char;
- R0.L='T';
- call .Lwait_char;
- R0.L='A';
- call .Lwait_char;
- R0.L='T';
- call .Lwait_char;
- R0.L='=';
- call .Lwait_char;
- R2 = SEQSTAT;
- call .Ldump_reg;
-
- R0.L=' ';
- call .Lwait_char;
- R0.L='R';
- call .Lwait_char;
- R0.L='E'
- call .Lwait_char;
- R0.L='T'
- call .Lwait_char;
- R0.L='X';
- call .Lwait_char;
- R0.L='=';
- call .Lwait_char;
- R2 = RETX;
- call .Ldump_reg;
-
- R0.L='\r';
- call .Lwait_char;
- R0.L='\n';
- call .Lwait_char;
-
-.Ldebug_kernel_start_trap_done:
- JUMP .Ldebug_kernel_start_trap_done;
-.Ldump_reg:
- R3 = 32;
- R4 = 0x0F;
- R5 = ':'; /* one past 9 */
-
-.Ldump_reg2:
- R0 = R2;
- R3 += -4;
- R0 >>>= R3;
- R0 = R0 & R4;
- R0 += 0x30;
- CC = R0 <= R5;
- if CC JUMP .Ldump_reg1;
- R0 += 7;
-
-.Ldump_reg1:
- R1.l = W[P1];
- CC = BITTST(R1, 5);
- if !CC JUMP .Ldump_reg1;
- W[P0] = r0;
-
- CC = R3 == 0;
- if !CC JUMP .Ldump_reg2
- RTS;
-
-.Lwait_char:
- R1.l = W[P1];
- CC = BITTST(R1, 5);
- if !CC JUMP .Lwait_char;
- W[P0] = r0;
- RTS;
-
-#endif /* CONFIG_DEBUG_KERNEL_START */
-
.data
/*
menu "BF537 Specific Configuration"
-comment "PORT F/G Selection"
-choice
- prompt "Select BF537/6/4 default GPIO PFx PORTx"
- help
- Quick Hack for BF537/6/4 default GPIO PFx PORTF.
-
-config BF537_PORT_F
- bool "Select BF537/6/4 default GPIO PFx PORTF"
- depends on (BF537 || BF536 || BF534)
- help
- Quick Hack for BF537/6/4 default GPIO PFx PORTF.
-
-config BF537_PORT_G
- bool "Select BF537/6/4 default GPIO PFx PORTG"
- depends on (BF537 || BF536 || BF534)
- help
- Quick Hack for BF537/6/4 default GPIO PFx PORTG.
-
-config BF537_PORT_H
- bool "Select BF537/6/4 default GPIO PFx PORTH"
- depends on (BF537 || BF536 || BF534)
- help
- Quick Hack for BF537/6/4 default GPIO PFx PORTH
- Use only when Blackfin EMAC support is not required.
-
-endchoice
-
comment "Interrupt Priority Assignment"
menu "Priority"
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
#include <linux/usb_isp1362.h>
+#include <linux/pata_platform.h>
#include <linux/irq.h>
+#include <asm/dma.h>
#include <asm/bfin5xx_spi.h>
/*
/* the modalias must be the same as spi device driver name */
.modalias = "m25p80", /* Name of spi_driver for this device */
.max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1, /* Framework bus number */
+ .bus_num = 0, /* Framework bus number */
.chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/
.platform_data = &bfin_spi_flash_data,
.controller_data = &spi_flash_chip_info,
{
.modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
.max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1, /* Framework bus number */
+ .bus_num = 0, /* Framework bus number */
.chip_select = 1, /* Framework chip select. */
.platform_data = NULL, /* No spi_driver specific config */
.controller_data = &spi_adc_chip_info,
{
.modalias = "ad1836-spi",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1,
+ .bus_num = 0,
.chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
.controller_data = &ad1836_spi_chip_info,
},
{
.modalias = "ad9960-spi",
.max_speed_hz = 10000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1,
+ .bus_num = 0,
.chip_select = 1,
.controller_data = &ad9960_spi_chip_info,
},
{
.modalias = "spi_mmc_dummy",
.max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1,
+ .bus_num = 0,
.chip_select = 7,
.platform_data = NULL,
.controller_data = &spi_mmc_chip_info,
{
.modalias = "spi_mmc",
.max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1,
+ .bus_num = 0,
.chip_select = CONFIG_SPI_MMC_CS_CHAN,
.platform_data = NULL,
.controller_data = &spi_mmc_chip_info,
#endif
};
+/* SPI (0) */
+static struct resource bfin_spi0_resource[] = {
+ [0] = {
+ .start = SPI0_REGBASE,
+ .end = SPI0_REGBASE + 0xFF,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = CH_SPI,
+ .end = CH_SPI,
+ .flags = IORESOURCE_IRQ,
+ }
+};
+
/* SPI controller data */
-static struct bfin5xx_spi_master spi_bfin_master_info = {
+static struct bfin5xx_spi_master bfin_spi0_info = {
.num_chipselect = 8,
.enable_dma = 1, /* master has the ability to do dma transfer */
};
-static struct platform_device spi_bfin_master_device = {
- .name = "bfin-spi-master",
- .id = 1, /* Bus number */
+static struct platform_device bfin_spi0_device = {
+ .name = "bfin-spi",
+ .id = 0, /* Bus number */
+ .num_resources = ARRAY_SIZE(bfin_spi0_resource),
+ .resource = bfin_spi0_resource,
.dev = {
- .platform_data = &spi_bfin_master_info, /* Passed to driver */
+ .platform_data = &bfin_spi0_info, /* Passed to driver */
},
};
#endif /* spi master and devices */
};
#endif
+#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+#define PATA_INT 64
+
+static struct pata_platform_info bfin_pata_platform_data = {
+ .ioport_shift = 2,
+ .irq_type = IRQF_TRIGGER_HIGH | IRQF_DISABLED,
+};
+
+static struct resource bfin_pata_resources[] = {
+ {
+ .start = 0x2030C000,
+ .end = 0x2030C01F,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = 0x2030D018,
+ .end = 0x2030D01B,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = PATA_INT,
+ .end = PATA_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device bfin_pata_device = {
+ .name = "pata_platform",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(bfin_pata_resources),
+ .resource = bfin_pata_resources,
+ .dev = {
+ .platform_data = &bfin_pata_platform_data,
+ }
+};
+#endif
+
static struct platform_device *cm_bf537_devices[] __initdata = {
#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
&rtc_device,
#endif
#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
- &spi_bfin_master_device,
+ &bfin_spi0_device,
+#endif
+
+#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+ &bfin_pata_device,
#endif
};
#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
#endif
+
+#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+ irq_desc[PATA_INT].status |= IRQ_NOAUTOEN;
+#endif
return 0;
}
*
* Modified:
* Copyright 2005 National ICT Australia (NICTA)
- * Copyright 2004-2006 Analog Devices Inc.
+ * Copyright 2004-2007 Analog Devices Inc.
*
* Bugs: Enter bugs at http://blackfin.uclinux.org/
*
#include <linux/mtd/partitions.h>
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
+#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
#include <linux/usb_isp1362.h>
+#endif
+#include <linux/pata_platform.h>
#include <linux/irq.h>
+#include <linux/interrupt.h>
#include <linux/usb_sl811.h>
+#include <asm/dma.h>
#include <asm/bfin5xx_spi.h>
+#include <asm/reboot.h>
+#include <linux/spi/ad7877.h>
/*
* Name the Board for the /proc/cpuinfo
*/
-char *bfin_board_name = "UNKNOWN BOARD";
+char *bfin_board_name = "GENERIC Board";
/*
* Driver needs to know address, irq and flag pin.
*/
+#define ISP1761_BASE 0x203C0000
+#define ISP1761_IRQ IRQ_PF7
+
+#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
+static struct resource bfin_isp1761_resources[] = {
+ [0] = {
+ .name = "isp1761-regs",
+ .start = ISP1761_BASE + 0x00000000,
+ .end = ISP1761_BASE + 0x000fffff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = ISP1761_IRQ,
+ .end = ISP1761_IRQ,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device bfin_isp1761_device = {
+ .name = "isp1761",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(bfin_isp1761_resources),
+ .resource = bfin_isp1761_resources,
+};
+
+static struct platform_device *bfin_isp1761_devices[] = {
+ &bfin_isp1761_device,
+};
+
+int __init bfin_isp1761_init(void)
+{
+ unsigned int num_devices = ARRAY_SIZE(bfin_isp1761_devices);
+
+ printk(KERN_INFO "%s(): registering device resources\n", __FUNCTION__);
+ set_irq_type(ISP1761_IRQ, IRQF_TRIGGER_FALLING);
+
+ return platform_add_devices(bfin_isp1761_devices, num_devices);
+}
+
+void __exit bfin_isp1761_exit(void)
+{
+ platform_device_unregister(&bfin_isp1761_device);
+}
+
+arch_initcall(bfin_isp1761_init);
+#endif
+
#if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
static struct resource bfin_pcmcia_cf_resources[] = {
{
.start = 0x20311000, /* Attribute Memory */
.end = 0x20311FFF,
.flags = IORESOURCE_MEM,
- }, {
- .start = IRQ_PROG_INTA,
- .end = IRQ_PROG_INTA,
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
}, {
.start = IRQ_PF4,
.end = IRQ_PF4,
.end = 0x20300300 + 16,
.flags = IORESOURCE_MEM,
}, {
- .start = IRQ_PROG_INTB,
- .end = IRQ_PROG_INTB,
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
- }, {
- /*
- * denotes the flag pin and is used directly if
- * CONFIG_IRQCHIP_DEMUX_GPIO is defined.
- */
+
.start = IRQ_PF7,
.end = IRQ_PF7,
.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
};
#endif
+#if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
+static struct resource dm9000_resources[] = {
+ [0] = {
+ .start = 0x203FB800,
+ .end = 0x203FB800 + 8,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = IRQ_PF9,
+ .end = IRQ_PF9,
+ .flags = (IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE),
+ },
+};
+
+static struct platform_device dm9000_device = {
+ .name = "dm9000",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(dm9000_resources),
+ .resource = dm9000_resources,
+};
+#endif
+
#if defined(CONFIG_USB_SL811_HCD) || defined(CONFIG_USB_SL811_HCD_MODULE)
static struct resource sl811_hcd_resources[] = {
{
.end = 0x20340004,
.flags = IORESOURCE_MEM,
}, {
- .start = IRQ_PROG_INTA,
- .end = IRQ_PROG_INTA,
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
- }, {
- .start = IRQ_PF0 + CONFIG_USB_SL811_BFIN_GPIO,
- .end = IRQ_PF0 + CONFIG_USB_SL811_BFIN_GPIO,
+ .start = CONFIG_USB_SL811_BFIN_IRQ,
+ .end = CONFIG_USB_SL811_BFIN_IRQ,
.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
},
};
#if defined(CONFIG_USB_SL811_BFIN_USE_VBUS)
void sl811_port_power(struct device *dev, int is_on)
{
- unsigned short mask = (1<<CONFIG_USB_SL811_BFIN_GPIO_VBUS);
-
- bfin_write_PORT_FER(bfin_read_PORT_FER() & ~mask);
- bfin_write_FIO_DIR(bfin_read_FIO_DIR() | mask);
+ gpio_request(CONFIG_USB_SL811_BFIN_GPIO_VBUS, "usb:SL811_VBUS");
+ gpio_direction_output(CONFIG_USB_SL811_BFIN_GPIO_VBUS);
if (is_on)
- bfin_write_FIO_FLAG_S(mask);
+ gpio_set_value(CONFIG_USB_SL811_BFIN_GPIO_VBUS, 1);
else
- bfin_write_FIO_FLAG_C(mask);
+ gpio_set_value(CONFIG_USB_SL811_BFIN_GPIO_VBUS, 0);
}
#endif
static struct sl811_platform_data sl811_priv = {
.potpg = 10,
- .power = 250, /* == 500mA */
+ .power = 250, /* == 500mA */
#if defined(CONFIG_USB_SL811_BFIN_USE_VBUS)
.port_power = &sl811_port_power,
#endif
.num_resources = ARRAY_SIZE(sl811_hcd_resources),
.resource = sl811_hcd_resources,
};
-
#endif
#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
.end = 0x20360004,
.flags = IORESOURCE_MEM,
}, {
- .start = IRQ_PROG_INTA,
- .end = IRQ_PROG_INTA,
+ .start = CONFIG_USB_ISP1362_BFIN_GPIO_IRQ,
+ .end = CONFIG_USB_ISP1362_BFIN_GPIO_IRQ,
.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
- }, {
- .start = IRQ_PF0 + CONFIG_USB_ISP1362_BFIN_GPIO,
- .end = IRQ_PF0 + CONFIG_USB_ISP1362_BFIN_GPIO,
- .flags = IORESOURCE_IRQ,
},
};
#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
/* all SPI peripherals info goes here */
-#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+#if defined(CONFIG_MTD_M25P80) \
+ || defined(CONFIG_MTD_M25P80_MODULE)
static struct mtd_partition bfin_spi_flash_partitions[] = {
{
.name = "bootloader",
};
#endif
+#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
+static struct bfin5xx_spi_chip spi_mmc_chip_info = {
+ .enable_dma = 1,
+ .bits_per_word = 8,
+};
+#endif
+
+#if defined(CONFIG_PBX)
+static struct bfin5xx_spi_chip spi_si3xxx_chip_info = {
+ .ctl_reg = 0x4, /* send zero */
+ .enable_dma = 0,
+ .bits_per_word = 8,
+ .cs_change_per_word = 1,
+};
+#endif
+
+#if defined(CONFIG_AD5304) || defined(CONFIG_AD5304_MODULE)
+static struct bfin5xx_spi_chip ad5304_chip_info = {
+ .enable_dma = 0,
+ .bits_per_word = 16,
+};
+#endif
+
+#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
+ .enable_dma = 0,
+ .bits_per_word = 16,
+};
+
+static const struct ad7877_platform_data bfin_ad7877_ts_info = {
+ .model = 7877,
+ .vref_delay_usecs = 50, /* internal, no capacitor */
+ .x_plate_ohms = 419,
+ .y_plate_ohms = 486,
+ .pressure_max = 1000,
+ .pressure_min = 0,
+ .stopacq_polarity = 1,
+ .first_conversion_delay = 3,
+ .acquisition_time = 1,
+ .averaging = 1,
+ .pen_down_acc_interval = 1,
+};
+#endif
+
static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+#if defined(CONFIG_MTD_M25P80) \
+ || defined(CONFIG_MTD_M25P80_MODULE)
{
/* the modalias must be the same as spi device driver name */
.modalias = "m25p80", /* Name of spi_driver for this device */
.max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1, /* Framework bus number */
- .chip_select = 2, /* Framework chip select. On STAMP537 it is SPISSEL1*/
+ .bus_num = 0, /* Framework bus number */
+ .chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/
.platform_data = &bfin_spi_flash_data,
.controller_data = &spi_flash_chip_info,
.mode = SPI_MODE_3,
},
#endif
-#if defined(CONFIG_SPI_ADC_BF533) || defined(CONFIG_SPI_ADC_BF533_MODULE)
+#if defined(CONFIG_SPI_ADC_BF533) \
+ || defined(CONFIG_SPI_ADC_BF533_MODULE)
{
.modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
.max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1, /* Framework bus number */
+ .bus_num = 0, /* Framework bus number */
.chip_select = 1, /* Framework chip select. */
.platform_data = NULL, /* No spi_driver specific config */
.controller_data = &spi_adc_chip_info,
},
#endif
-#if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
+#if defined(CONFIG_SND_BLACKFIN_AD1836) \
+ || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
{
.modalias = "ad1836-spi",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1,
+ .bus_num = 0,
.chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
.controller_data = &ad1836_spi_chip_info,
},
#endif
-
#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
{
.modalias = "ad9960-spi",
.max_speed_hz = 10000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1,
+ .bus_num = 0,
.chip_select = 1,
.controller_data = &ad9960_spi_chip_info,
},
#endif
+#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
+ {
+ .modalias = "spi_mmc_dummy",
+ .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = 0,
+ .platform_data = NULL,
+ .controller_data = &spi_mmc_chip_info,
+ .mode = SPI_MODE_3,
+ },
+ {
+ .modalias = "spi_mmc",
+ .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = CONFIG_SPI_MMC_CS_CHAN,
+ .platform_data = NULL,
+ .controller_data = &spi_mmc_chip_info,
+ .mode = SPI_MODE_3,
+ },
+#endif
+#if defined(CONFIG_PBX)
+ {
+ .modalias = "fxs-spi",
+ .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = 8 - CONFIG_J11_JUMPER,
+ .controller_data = &spi_si3xxx_chip_info,
+ .mode = SPI_MODE_3,
+ },
+ {
+ .modalias = "fxo-spi",
+ .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = 8 - CONFIG_J19_JUMPER,
+ .controller_data = &spi_si3xxx_chip_info,
+ .mode = SPI_MODE_3,
+ },
+#endif
+#if defined(CONFIG_AD5304) || defined(CONFIG_AD5304_MODULE)
+ {
+ .modalias = "ad5304_spi",
+ .max_speed_hz = 1250000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = 2,
+ .platform_data = NULL,
+ .controller_data = &ad5304_chip_info,
+ .mode = SPI_MODE_2,
+ },
+#endif
+#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+ {
+ .modalias = "ad7877",
+ .platform_data = &bfin_ad7877_ts_info,
+ .irq = IRQ_PF6,
+ .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 1,
+ .chip_select = 1,
+ .controller_data = &spi_ad7877_chip_info,
+ },
+#endif
};
/* SPI controller data */
-static struct bfin5xx_spi_master spi_bfin_master_info = {
+static struct bfin5xx_spi_master bfin_spi0_info = {
.num_chipselect = 8,
.enable_dma = 1, /* master has the ability to do dma transfer */
};
-static struct platform_device spi_bfin_master_device = {
- .name = "bfin-spi-master",
- .id = 1, /* Bus number */
+/* SPI (0) */
+static struct resource bfin_spi0_resource[] = {
+ [0] = {
+ .start = SPI0_REGBASE,
+ .end = SPI0_REGBASE + 0xFF,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = CH_SPI,
+ .end = CH_SPI,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device bfin_spi0_device = {
+ .name = "bfin-spi",
+ .id = 0, /* Bus number */
+ .num_resources = ARRAY_SIZE(bfin_spi0_resource),
+ .resource = bfin_spi0_resource,
.dev = {
- .platform_data = &spi_bfin_master_info, /* Passed to driver */
+ .platform_data = &bfin_spi0_info, /* Passed to driver */
},
};
#endif /* spi master and devices */
#if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE)
static struct platform_device bfin_fb_device = {
- .name = "bf537-fb",
+ .name = "bf537-lq035",
+};
+#endif
+
+#if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE)
+static struct platform_device bfin_fb_adv7393_device = {
+ .name = "bfin-adv7393",
};
#endif
};
#endif
-static struct platform_device *stamp_devices[] __initdata = {
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
- &rtc_device,
+#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+static struct resource bfin_twi0_resource[] = {
+ [0] = {
+ .start = TWI0_REGBASE,
+ .end = TWI0_REGBASE + 0xFF,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = IRQ_TWI,
+ .end = IRQ_TWI,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device i2c_bfin_twi_device = {
+ .name = "i2c-bfin-twi",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(bfin_twi0_resource),
+ .resource = bfin_twi0_resource,
+};
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+static struct platform_device bfin_sport0_uart_device = {
+ .name = "bfin-sport-uart",
+ .id = 0,
+};
+
+static struct platform_device bfin_sport1_uart_device = {
+ .name = "bfin-sport-uart",
+ .id = 1,
+};
+#endif
+
+#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+#define PATA_INT 55
+
+static struct pata_platform_info bfin_pata_platform_data = {
+ .ioport_shift = 1,
+ .irq_type = IRQF_TRIGGER_HIGH | IRQF_DISABLED,
+};
+
+static struct resource bfin_pata_resources[] = {
+ {
+ .start = 0x20314020,
+ .end = 0x2031403F,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = 0x2031401C,
+ .end = 0x2031401F,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = PATA_INT,
+ .end = PATA_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device bfin_pata_device = {
+ .name = "pata_platform",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(bfin_pata_resources),
+ .resource = bfin_pata_resources,
+ .dev = {
+ .platform_data = &bfin_pata_platform_data,
+ }
+};
#endif
+static struct platform_device *stamp_devices[] __initdata = {
#if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
&bfin_pcmcia_cf_device,
#endif
+#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+ &rtc_device,
+#endif
+
#if defined(CONFIG_USB_SL811_HCD) || defined(CONFIG_USB_SL811_HCD_MODULE)
&sl811_hcd_device,
#endif
&smc91x_device,
#endif
+#if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
+ &dm9000_device,
+#endif
+
#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
&bfin_mac_device,
#endif
#endif
#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
- &spi_bfin_master_device,
+ &bfin_spi0_device,
#endif
#if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE)
&bfin_fb_device,
#endif
+#if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE)
+ &bfin_fb_adv7393_device,
+#endif
+
#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
&bfin_uart_device,
#endif
+
+#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+ &i2c_bfin_twi_device,
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+ &bfin_sport0_uart_device,
+ &bfin_sport1_uart_device,
+#endif
+
+#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+ &bfin_pata_device,
+#endif
};
static int __init stamp_init(void)
printk(KERN_INFO "%s(): registering device resources\n", __FUNCTION__);
platform_add_devices(stamp_devices, ARRAY_SIZE(stamp_devices));
#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
- spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
+ spi_register_board_info(bfin_spi_board_info,
+ ARRAY_SIZE(bfin_spi_board_info));
+#endif
+
+#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+ irq_desc[PATA_INT].status |= IRQ_NOAUTOEN;
#endif
return 0;
}
arch_initcall(stamp_init);
+
+void native_machine_restart(char *cmd)
+{
+ /* workaround reboot hang when booting from SPI */
+ if ((bfin_read_SYSCR() & 0x7) == 0x3)
+ bfin_gpio_reset_spi0_ssel1();
+}
#include <linux/usb_isp1362.h>
#endif
#include <linux/irq.h>
+#include <asm/dma.h>
#include <asm/bfin5xx_spi.h>
#include <linux/usb_sl811.h>
#if defined(CONFIG_USB_SL811_BFIN_USE_VBUS)
void sl811_port_power(struct device *dev, int is_on)
{
- unsigned short mask = (1 << CONFIG_USB_SL811_BFIN_GPIO_VBUS);
-
- bfin_write_PORT_FER(bfin_read_PORT_FER() & ~mask);
- bfin_write_FIO_DIR(bfin_read_FIO_DIR() | mask);
+ gpio_request(CONFIG_USB_SL811_BFIN_GPIO_VBUS, "usb:SL811_VBUS");
+ gpio_direction_output(CONFIG_USB_SL811_BFIN_GPIO_VBUS);
if (is_on)
- bfin_write_FIO_FLAG_S(mask);
+ gpio_set_value(CONFIG_USB_SL811_BFIN_GPIO_VBUS, 1);
else
- bfin_write_FIO_FLAG_C(mask);
+ gpio_set_value(CONFIG_USB_SL811_BFIN_GPIO_VBUS, 0);
}
#endif
/* the modalias must be the same as spi device driver name */
.modalias = "m25p80", /* Name of spi_driver for this device */
.max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1, /* Framework bus number */
+ .bus_num = 0, /* Framework bus number */
.chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/
.platform_data = &bfin_spi_flash_data,
.controller_data = &spi_flash_chip_info,
{
.modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
.max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1, /* Framework bus number */
+ .bus_num = 0, /* Framework bus number */
.chip_select = 1, /* Framework chip select. */
.platform_data = NULL, /* No spi_driver specific config */
.controller_data = &spi_adc_chip_info,
{
.modalias = "ad1836-spi",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1,
+ .bus_num = 0,
.chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
.controller_data = &ad1836_spi_chip_info,
},
{
.modalias = "ad9960-spi",
.max_speed_hz = 10000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1,
+ .bus_num = 0,
.chip_select = 1,
.controller_data = &ad9960_spi_chip_info,
},
{
.modalias = "spi_mmc_dummy",
.max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1,
+ .bus_num = 0,
.chip_select = 7,
.platform_data = NULL,
.controller_data = &spi_mmc_chip_info,
{
.modalias = "spi_mmc",
.max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1,
+ .bus_num = 0,
.chip_select = CONFIG_SPI_MMC_CS_CHAN,
.platform_data = NULL,
.controller_data = &spi_mmc_chip_info,
};
+/* SPI (0) */
+static struct resource bfin_spi0_resource[] = {
+ [0] = {
+ .start = SPI0_REGBASE,
+ .end = SPI0_REGBASE + 0xFF,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = CH_SPI,
+ .end = CH_SPI,
+ .flags = IORESOURCE_IRQ,
+ }
+};
+
/* SPI controller data */
-static struct bfin5xx_spi_master spi_bfin_master_info = {
+static struct bfin5xx_spi_master bfin_spi0_info = {
.num_chipselect = 8,
.enable_dma = 1, /* master has the ability to do dma transfer */
};
-static struct platform_device spi_bfin_master_device = {
- .name = "bfin-spi-master",
- .id = 1, /* Bus number */
+static struct platform_device bfin_spi0_device = {
+ .name = "bfin-spi",
+ .id = 0, /* Bus number */
+ .num_resources = ARRAY_SIZE(bfin_spi0_resource),
+ .resource = bfin_spi0_resource,
.dev = {
- .platform_data = &spi_bfin_master_info, /* Passed to driver */
+ .platform_data = &bfin_spi0_info, /* Passed to driver */
},
};
#endif /* spi master and devices */
#if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE)
static struct platform_device bfin_fb_device = {
- .name = "bf537-fb",
+ .name = "bf537-lq035",
};
#endif
#endif
#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
- &spi_bfin_master_device,
+ &bfin_spi0_device,
#endif
#if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE)
#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
#include <linux/usb_isp1362.h>
#endif
+#include <linux/pata_platform.h>
#include <linux/irq.h>
#include <linux/interrupt.h>
#include <linux/usb_sl811.h>
+#include <asm/dma.h>
#include <asm/bfin5xx_spi.h>
+#include <asm/reboot.h>
#include <linux/spi/ad7877.h>
/*
#if defined(CONFIG_USB_SL811_BFIN_USE_VBUS)
void sl811_port_power(struct device *dev, int is_on)
{
- unsigned short mask = (1 << CONFIG_USB_SL811_BFIN_GPIO_VBUS);
-
- bfin_write_PORT_FER(bfin_read_PORT_FER() & ~mask);
- bfin_write_FIO_DIR(bfin_read_FIO_DIR() | mask);
+ gpio_request(CONFIG_USB_SL811_BFIN_GPIO_VBUS, "usb:SL811_VBUS");
+ gpio_direction_output(CONFIG_USB_SL811_BFIN_GPIO_VBUS);
if (is_on)
- bfin_write_FIO_FLAG_S(mask);
+ gpio_set_value(CONFIG_USB_SL811_BFIN_GPIO_VBUS, 1);
else
- bfin_write_FIO_FLAG_C(mask);
+ gpio_set_value(CONFIG_USB_SL811_BFIN_GPIO_VBUS, 0);
}
#endif
/* the modalias must be the same as spi device driver name */
.modalias = "m25p80", /* Name of spi_driver for this device */
.max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1, /* Framework bus number */
+ .bus_num = 0, /* Framework bus number */
.chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/
.platform_data = &bfin_spi_flash_data,
.controller_data = &spi_flash_chip_info,
{
.modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
.max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1, /* Framework bus number */
+ .bus_num = 0, /* Framework bus number */
.chip_select = 1, /* Framework chip select. */
.platform_data = NULL, /* No spi_driver specific config */
.controller_data = &spi_adc_chip_info,
{
.modalias = "ad1836-spi",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1,
+ .bus_num = 0,
.chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
.controller_data = &ad1836_spi_chip_info,
},
{
.modalias = "ad9960-spi",
.max_speed_hz = 10000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1,
+ .bus_num = 0,
.chip_select = 1,
.controller_data = &ad9960_spi_chip_info,
},
{
.modalias = "spi_mmc_dummy",
.max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1,
+ .bus_num = 0,
.chip_select = 0,
.platform_data = NULL,
.controller_data = &spi_mmc_chip_info,
{
.modalias = "spi_mmc",
.max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1,
+ .bus_num = 0,
.chip_select = CONFIG_SPI_MMC_CS_CHAN,
.platform_data = NULL,
.controller_data = &spi_mmc_chip_info,
{
.modalias = "fxs-spi",
.max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1,
- .chip_select = 3,
+ .bus_num = 0,
+ .chip_select = 8 - CONFIG_J11_JUMPER,
.controller_data = &spi_si3xxx_chip_info,
.mode = SPI_MODE_3,
},
{
.modalias = "fxo-spi",
.max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1,
- .chip_select = 2,
+ .bus_num = 0,
+ .chip_select = 8 - CONFIG_J19_JUMPER,
.controller_data = &spi_si3xxx_chip_info,
.mode = SPI_MODE_3,
},
{
.modalias = "ad5304_spi",
.max_speed_hz = 1250000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1,
+ .bus_num = 0,
.chip_select = 2,
.platform_data = NULL,
.controller_data = &ad5304_chip_info,
};
/* SPI controller data */
-static struct bfin5xx_spi_master spi_bfin_master_info = {
+static struct bfin5xx_spi_master bfin_spi0_info = {
.num_chipselect = 8,
.enable_dma = 1, /* master has the ability to do dma transfer */
};
-static struct platform_device spi_bfin_master_device = {
- .name = "bfin-spi-master",
- .id = 1, /* Bus number */
+/* SPI (0) */
+static struct resource bfin_spi0_resource[] = {
+ [0] = {
+ .start = SPI0_REGBASE,
+ .end = SPI0_REGBASE + 0xFF,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = CH_SPI,
+ .end = CH_SPI,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device bfin_spi0_device = {
+ .name = "bfin-spi",
+ .id = 0, /* Bus number */
+ .num_resources = ARRAY_SIZE(bfin_spi0_resource),
+ .resource = bfin_spi0_resource,
.dev = {
- .platform_data = &spi_bfin_master_info, /* Passed to driver */
+ .platform_data = &bfin_spi0_info, /* Passed to driver */
},
};
#endif /* spi master and devices */
#if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE)
static struct platform_device bfin_fb_device = {
- .name = "bf537-fb",
+ .name = "bf537-lq035",
+};
+#endif
+
+#if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE)
+static struct platform_device bfin_fb_adv7393_device = {
+ .name = "bfin-adv7393",
};
#endif
#endif
#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+static struct resource bfin_twi0_resource[] = {
+ [0] = {
+ .start = TWI0_REGBASE,
+ .end = TWI0_REGBASE,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = IRQ_TWI,
+ .end = IRQ_TWI,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
static struct platform_device i2c_bfin_twi_device = {
.name = "i2c-bfin-twi",
.id = 0,
+ .num_resources = ARRAY_SIZE(bfin_twi0_resource),
+ .resource = bfin_twi0_resource,
};
#endif
};
#endif
+#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+#define PATA_INT 55
+
+static struct pata_platform_info bfin_pata_platform_data = {
+ .ioport_shift = 1,
+ .irq_type = IRQF_TRIGGER_HIGH | IRQF_DISABLED,
+};
+
+static struct resource bfin_pata_resources[] = {
+ {
+ .start = 0x20314020,
+ .end = 0x2031403F,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = 0x2031401C,
+ .end = 0x2031401F,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = PATA_INT,
+ .end = PATA_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device bfin_pata_device = {
+ .name = "pata_platform",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(bfin_pata_resources),
+ .resource = bfin_pata_resources,
+ .dev = {
+ .platform_data = &bfin_pata_platform_data,
+ }
+};
+#endif
+
static struct platform_device *stamp_devices[] __initdata = {
#if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
&bfin_pcmcia_cf_device,
#endif
#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
- &spi_bfin_master_device,
+ &bfin_spi0_device,
#endif
#if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE)
&bfin_fb_device,
#endif
+#if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE)
+ &bfin_fb_adv7393_device,
+#endif
+
#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
&bfin_uart_device,
#endif
&bfin_sport0_uart_device,
&bfin_sport1_uart_device,
#endif
+
+#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+ &bfin_pata_device,
+#endif
};
static int __init stamp_init(void)
spi_register_board_info(bfin_spi_board_info,
ARRAY_SIZE(bfin_spi_board_info));
#endif
+
+#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+ irq_desc[PATA_INT].status |= IRQ_NOAUTOEN;
+#endif
return 0;
}
arch_initcall(stamp_init);
+
+void native_machine_restart(char *cmd)
+{
+ /* workaround reboot hang when booting from SPI */
+ if ((bfin_read_SYSCR() & 0x7) == 0x3)
+ bfin_gpio_reset_spi0_ssel1();
+}
#include <asm/trace.h>
#if CONFIG_BFIN_KERNEL_CLOCK
+#include <asm/mach-common/clocks.h>
#include <asm/mach/mem_init.h>
#endif
ENTRY(__start)
/* R0: argument of command line string, passed from uboot, save it */
R7 = R0;
- /* Set the SYSCFG register:
- * Enable Cycle Counter and Nesting Of Interrupts (3rd Bit)
- */
- R0 = 0x36;
+ /* Enable Cycle Counter and Nesting Of Interrupts */
+#ifdef CONFIG_BFIN_SCRATCH_REG_CYCLES
+ R0 = SYSCFG_SNEN;
+#else
+ R0 = SYSCFG_SNEN | SYSCFG_CCEN;
+#endif
SYSCFG = R0;
R0 = 0;
M2 = r0;
M3 = r0;
- trace_buffer_start(p0,r0);
+ trace_buffer_init(p0,r0);
P0 = R1;
R0 = R1;
/* Turn off the icache */
- p0.l = (IMEM_CONTROL & 0xFFFF);
- p0.h = (IMEM_CONTROL >> 16);
+ p0.l = LO(IMEM_CONTROL);
+ p0.h = HI(IMEM_CONTROL);
R1 = [p0];
R0 = ~ENICPLB;
R0 = R0 & R1;
/* Anomaly 05000125 */
-#ifdef ANOMALY_05000125
+#if ANOMALY_05000125
CLI R2;
SSYNC;
#endif
[p0] = R0;
SSYNC;
-#ifdef ANOMALY_05000125
+#if ANOMALY_05000125
STI R2;
#endif
/* Turn off the dcache */
- p0.l = (DMEM_CONTROL & 0xFFFF);
- p0.h = (DMEM_CONTROL >> 16);
+ p0.l = LO(DMEM_CONTROL);
+ p0.h = HI(DMEM_CONTROL);
R1 = [p0];
R0 = ~ENDCPLB;
R0 = R0 & R1;
/* Anomaly 05000125 */
-#ifdef ANOMALY_05000125
+#if ANOMALY_05000125
CLI R2;
SSYNC;
#endif
[p0] = R0;
SSYNC;
-#ifdef ANOMALY_05000125
+#if ANOMALY_05000125
STI R2;
#endif
*/
p0.h = hi(BFIN_PORT_MUX);
p0.l = lo(BFIN_PORT_MUX);
-#ifdef ANOMALY_05000212
+#if ANOMALY_05000212
R0.L = W[P0]; /* Read */
SSYNC;
#endif
R0 = (PGDE_UART | PFTE_UART)(Z);
-#ifdef ANOMALY_05000212
+#if ANOMALY_05000212
W[P0] = R0.L; /* Write */
SSYNC;
#endif
p0.h = hi(PORTF_FER);
p0.l = lo(PORTF_FER);
-#ifdef ANOMALY_05000212
+#if ANOMALY_05000212
R0.L = W[P0]; /* Read */
SSYNC;
#endif
R0 = 0x000F(Z);
-#ifdef ANOMALY_05000212
+#if ANOMALY_05000212
W[P0] = R0.L; /* Write */
SSYNC;
#endif
fp = sp;
usp = sp;
+#ifdef CONFIG_EARLY_PRINTK
+ SP += -12;
+ call _init_early_exception_vectors;
+ SP += 12;
+#endif
+
/* Put The Code for PLL Programming and SDRAM Programming in L1 ISRAM */
call _bf53x_relocate_l1_mem;
#if CONFIG_BFIN_KERNEL_CLOCK
p0.l = .LWAIT_HERE;
p0.h = .LWAIT_HERE;
reti = p0;
-#if defined(ANOMALY_05000281)
+#if ANOMALY_05000281
nop; nop; nop;
#endif
rti;
w[p0] = r0.l;
ssync;
- p0.l = (EBIU_SDBCTL & 0xFFFF);
- p0.h = (EBIU_SDBCTL >> 16); /* SDRAM Memory Bank Control Register */
+ p0.l = LO(EBIU_SDBCTL);
+ p0.h = HI(EBIU_SDBCTL); /* SDRAM Memory Bank Control Register */
r0 = mem_SDBCTL;
w[p0] = r0.l;
ssync;
ENDPROC(_start_dma_code)
#endif /* CONFIG_BFIN_KERNEL_CLOCK */
-ENTRY(_bfin_reset)
- /* No more interrupts to be handled*/
- CLI R6;
- SSYNC;
-
-#if defined(CONFIG_MTD_M25P80)
- /*
- * The following code fix the SPI flash reboot issue,
- * /CS signal of the chip which is using PF10 return to GPIO mode
- */
- p0.h = hi(PORTF_FER);
- p0.l = lo(PORTF_FER);
- r0.l = 0x0000;
- w[p0] = r0.l;
- SSYNC;
-
- /* /CS return to high */
- p0.h = hi(PORTFIO);
- p0.l = lo(PORTFIO);
- r0.l = 0xFFFF;
- w[p0] = r0.l;
- SSYNC;
-
- /* Delay some time, This is necessary */
- r1.h = 0;
- r1.l = 0x400;
- p1 = r1;
- lsetup (.L_delay_lab1, .L_delay_lab1_end) lc1 = p1;
-.L_delay_lab1:
- r0.h = 0;
- r0.l = 0x8000;
- p0 = r0;
- lsetup (.L_delay_lab0, .L_delay_lab0_end) lc0 = p0;
-.L_delay_lab0:
- nop;
-.L_delay_lab0_end:
- nop;
-.L_delay_lab1_end:
- nop;
-#endif
-
- /* Clear the IMASK register */
- p0.h = hi(IMASK);
- p0.l = lo(IMASK);
- r0 = 0x0;
- [p0] = r0;
-
- /* Clear the ILAT register */
- p0.h = hi(ILAT);
- p0.l = lo(ILAT);
- r0 = [p0];
- [p0] = r0;
- SSYNC;
-
- /* make sure SYSCR is set to use BMODE */
- P0.h = hi(SYSCR);
- P0.l = lo(SYSCR);
- R0.l = 0x0;
- W[P0] = R0.l;
- SSYNC;
-
- /* issue a system soft reset */
- P1.h = hi(SWRST);
- P1.l = lo(SWRST);
- R1.l = 0x0007;
- W[P1] = R1;
- SSYNC;
-
- /* clear system soft reset */
- R0.l = 0x0000;
- W[P0] = R0;
- SSYNC;
-
- /* issue core reset */
- raise 1;
-
- RTS;
-ENDPROC(_bfin_reset)
-
.data
/*
menu "BF548 Specific Configuration"
+config DEB_DMA_URGENT
+ bool "DMA has priority over core for ext. accesses"
+ depends on BF54x
+ default n
+ help
+ Treat any DEB1, DEB2 and DEB3 request as Urgent
+
comment "Interrupt Priority Assignment"
menu "Priority"
config PINTx_REASSIGN
bool "Reprogram PINT Assignment"
- default n
+ default y
help
The interrupt assignment registers controls the pin-to-interrupt
assignment in a byte-wide manner. Each option allows you to select
config PINT2_ASSIGN
hex "PINT2_ASSIGN"
depends on PINTx_REASSIGN
- default 0x00000101
+ default 0x07000101
config PINT3_ASSIGN
hex "PINT3_ASSIGN"
depends on PINTx_REASSIGN
extra-y := head.o
-obj-y := ints-priority.o dma.o gpio.o
+obj-y := ints-priority.o dma.o
obj-$(CONFIG_CPU_FREQ) += cpu.o
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
#include <linux/irq.h>
-#include <linux/irq.h>
#include <linux/interrupt.h>
+#include <linux/usb/musb.h>
#include <asm/bfin5xx_spi.h>
+#include <asm/cplb.h>
+#include <asm/dma.h>
+#include <asm/gpio.h>
+#include <asm/nand.h>
+#include <asm/mach/bf54x_keys.h>
+#include <linux/input.h>
+#include <linux/spi/ad7877.h>
/*
* Name the Board for the /proc/cpuinfo
* Driver needs to know address, irq and flag pin.
*/
+#if defined(CONFIG_FB_BF54X_LQ043) || defined(CONFIG_FB_BF54X_LQ043_MODULE)
+
+#include <asm/mach/bf54x-lq043.h>
+
+static struct bfin_bf54xfb_mach_info bf54x_lq043_data = {
+ .width = 480,
+ .height = 272,
+ .xres = {480, 480, 480},
+ .yres = {272, 272, 272},
+ .bpp = {24, 24, 24},
+ .disp = GPIO_PE3,
+};
+
+static struct resource bf54x_lq043_resources[] = {
+ {
+ .start = IRQ_EPPI0_ERR,
+ .end = IRQ_EPPI0_ERR,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device bf54x_lq043_device = {
+ .name = "bf54x-lq043",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(bf54x_lq043_resources),
+ .resource = bf54x_lq043_resources,
+ .dev = {
+ .platform_data = &bf54x_lq043_data,
+ },
+};
+#endif
+
+#if defined(CONFIG_KEYBOARD_BFIN) || defined(CONFIG_KEYBOARD_BFIN_MODULE)
+static int bf548_keymap[] = {
+ KEYVAL(0, 0, KEY_ENTER),
+ KEYVAL(0, 1, KEY_HELP),
+ KEYVAL(0, 2, KEY_0),
+ KEYVAL(0, 3, KEY_BACKSPACE),
+ KEYVAL(1, 0, KEY_TAB),
+ KEYVAL(1, 1, KEY_9),
+ KEYVAL(1, 2, KEY_8),
+ KEYVAL(1, 3, KEY_7),
+ KEYVAL(2, 0, KEY_DOWN),
+ KEYVAL(2, 1, KEY_6),
+ KEYVAL(2, 2, KEY_5),
+ KEYVAL(2, 3, KEY_4),
+ KEYVAL(3, 0, KEY_UP),
+ KEYVAL(3, 1, KEY_3),
+ KEYVAL(3, 2, KEY_2),
+ KEYVAL(3, 3, KEY_1),
+};
+
+static struct bfin_kpad_platform_data bf54x_kpad_data = {
+ .rows = 4,
+ .cols = 4,
+ .keymap = bf548_keymap,
+ .keymapsize = ARRAY_SIZE(bf548_keymap),
+ .repeat = 0,
+ .debounce_time = 5000, /* ns (5ms) */
+ .coldrive_time = 1000, /* ns (1ms) */
+ .keyup_test_interval = 50, /* ms (50ms) */
+};
+
+static struct resource bf54x_kpad_resources[] = {
+ {
+ .start = IRQ_KEY,
+ .end = IRQ_KEY,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device bf54x_kpad_device = {
+ .name = "bf54x-keys",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(bf54x_kpad_resources),
+ .resource = bf54x_kpad_resources,
+ .dev = {
+ .platform_data = &bf54x_kpad_data,
+ },
+};
+#endif
+
#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
static struct platform_device rtc_device = {
.name = "rtc-bfin",
};
#endif
+#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
+static struct resource smsc911x_resources[] = {
+ {
+ .name = "smsc911x-memory",
+ .start = 0x24000000,
+ .end = 0x24000000 + 0xFF,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = IRQ_PE8,
+ .end = IRQ_PE8,
+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
+ },
+};
+static struct platform_device smsc911x_device = {
+ .name = "smsc911x",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(smsc911x_resources),
+ .resource = smsc911x_resources,
+};
+#endif
+
+#if defined(CONFIG_USB_BF54x_HCD) || defined(CONFIG_USB_BF54x_HCD_MODULE)
+static struct resource bf54x_hcd_resources[] = {
+ {
+ .start = 0xFFC03C00,
+ .end = 0xFFC040FF,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct platform_device bf54x_hcd = {
+ .name = "bf54x-hcd",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(bf54x_hcd_resources),
+ .resource = bf54x_hcd_resources,
+};
+#endif
+
+#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+static struct resource musb_resources[] = {
+ [0] = {
+ .start = 0xFFC03C00,
+ .end = 0xFFC040FF,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = { /* general IRQ */
+ .start = IRQ_USB_INT0,
+ .end = IRQ_USB_INT0,
+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+ },
+ [2] = { /* DMA IRQ */
+ .start = IRQ_USB_DMA,
+ .end = IRQ_USB_DMA,
+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+ },
+};
+
+static struct musb_hdrc_platform_data musb_plat = {
+#ifdef CONFIG_USB_MUSB_OTG
+ .mode = MUSB_OTG,
+#elif CONFIG_USB_MUSB_HDRC_HCD
+ .mode = MUSB_HOST,
+#elif CONFIG_USB_GADGET_MUSB_HDRC
+ .mode = MUSB_PERIPHERAL,
+#endif
+ .multipoint = 1,
+};
+
+static u64 musb_dmamask = ~(u32)0;
+
+static struct platform_device musb_device = {
+ .name = "musb_hdrc",
+ .id = 0,
+ .dev = {
+ .dma_mask = &musb_dmamask,
+ .coherent_dma_mask = 0xffffffff,
+ .platform_data = &musb_plat,
+ },
+ .num_resources = ARRAY_SIZE(musb_resources),
+ .resource = musb_resources,
+};
+#endif
+
+#if defined(CONFIG_PATA_BF54X) || defined(CONFIG_PATA_BF54X_MODULE)
+static struct resource bfin_atapi_resources[] = {
+ {
+ .start = 0xFFC03800,
+ .end = 0xFFC0386F,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = IRQ_ATAPI_ERR,
+ .end = IRQ_ATAPI_ERR,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device bfin_atapi_device = {
+ .name = "pata-bf54x",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(bfin_atapi_resources),
+ .resource = bfin_atapi_resources,
+};
+#endif
+
+#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
+static struct mtd_partition partition_info[] = {
+ {
+ .name = "Linux Kernel",
+ .offset = 0,
+ .size = 4 * SIZE_1M,
+ },
+ {
+ .name = "File System",
+ .offset = 4 * SIZE_1M,
+ .size = (256 - 4) * SIZE_1M,
+ },
+};
+
+static struct bf5xx_nand_platform bf5xx_nand_platform = {
+ .page_size = NFC_PG_SIZE_256,
+ .data_width = NFC_NWIDTH_8,
+ .partitions = partition_info,
+ .nr_partitions = ARRAY_SIZE(partition_info),
+ .rd_dly = 3,
+ .wr_dly = 3,
+};
+
+static struct resource bf5xx_nand_resources[] = {
+ {
+ .start = 0xFFC03B00,
+ .end = 0xFFC03B4F,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = CH_NFC,
+ .end = CH_NFC,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device bf5xx_nand_device = {
+ .name = "bf5xx-nand",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(bf5xx_nand_resources),
+ .resource = bf5xx_nand_resources,
+ .dev = {
+ .platform_data = &bf5xx_nand_platform,
+ },
+};
+#endif
+
+#if defined(CONFIG_SDH_BFIN) || defined(CONFIG_SDH_BFIN)
+static struct platform_device bf54x_sdh_device = {
+ .name = "bfin-sdh",
+ .id = 0,
+};
+#endif
+
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+/* all SPI peripherals info goes here */
+#if defined(CONFIG_MTD_M25P80) \
+ || defined(CONFIG_MTD_M25P80_MODULE)
+/* SPI flash chip (m25p16) */
+static struct mtd_partition bfin_spi_flash_partitions[] = {
+ {
+ .name = "bootloader",
+ .size = 0x00040000,
+ .offset = 0,
+ .mask_flags = MTD_CAP_ROM
+ }, {
+ .name = "linux kernel",
+ .size = 0x1c0000,
+ .offset = 0x40000
+ }
+};
+
+static struct flash_platform_data bfin_spi_flash_data = {
+ .name = "m25p80",
+ .parts = bfin_spi_flash_partitions,
+ .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions),
+ .type = "m25p16",
+};
+
+static struct bfin5xx_spi_chip spi_flash_chip_info = {
+ .enable_dma = 0, /* use dma transfer with this chip*/
+ .bits_per_word = 8,
+ .cs_change_per_word = 0,
+};
+#endif
+
+#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
+ .cs_change_per_word = 1,
+ .enable_dma = 0,
+ .bits_per_word = 16,
+};
+
+static const struct ad7877_platform_data bfin_ad7877_ts_info = {
+ .model = 7877,
+ .vref_delay_usecs = 50, /* internal, no capacitor */
+ .x_plate_ohms = 419,
+ .y_plate_ohms = 486,
+ .pressure_max = 1000,
+ .pressure_min = 0,
+ .stopacq_polarity = 1,
+ .first_conversion_delay = 3,
+ .acquisition_time = 1,
+ .averaging = 1,
+ .pen_down_acc_interval = 1,
+};
+#endif
+
+static struct spi_board_info bf54x_spi_board_info[] __initdata = {
+#if defined(CONFIG_MTD_M25P80) \
+ || defined(CONFIG_MTD_M25P80_MODULE)
+ {
+ /* the modalias must be the same as spi device driver name */
+ .modalias = "m25p80", /* Name of spi_driver for this device */
+ .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0, /* Framework bus number */
+ .chip_select = 1, /* SPI_SSEL1*/
+ .platform_data = &bfin_spi_flash_data,
+ .controller_data = &spi_flash_chip_info,
+ .mode = SPI_MODE_3,
+ },
+#endif
+#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+{
+ .modalias = "ad7877",
+ .platform_data = &bfin_ad7877_ts_info,
+ .irq = IRQ_PJ11,
+ .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = 2,
+ .controller_data = &spi_ad7877_chip_info,
+},
+#endif
+};
+
+/* SPI (0) */
+static struct resource bfin_spi0_resource[] = {
+ [0] = {
+ .start = SPI0_REGBASE,
+ .end = SPI0_REGBASE + 0xFF,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = CH_SPI0,
+ .end = CH_SPI0,
+ .flags = IORESOURCE_IRQ,
+ }
+};
+
+/* SPI (1) */
+static struct resource bfin_spi1_resource[] = {
+ [0] = {
+ .start = SPI1_REGBASE,
+ .end = SPI1_REGBASE + 0xFF,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = CH_SPI1,
+ .end = CH_SPI1,
+ .flags = IORESOURCE_IRQ,
+ }
+};
+
+/* SPI controller data */
+static struct bfin5xx_spi_master bf54x_spi_master_info = {
+ .num_chipselect = 8,
+ .enable_dma = 1, /* master has the ability to do dma transfer */
+};
+
+static struct platform_device bf54x_spi_master0 = {
+ .name = "bfin-spi",
+ .id = 0, /* Bus number */
+ .num_resources = ARRAY_SIZE(bfin_spi0_resource),
+ .resource = bfin_spi0_resource,
+ .dev = {
+ .platform_data = &bf54x_spi_master_info, /* Passed to driver */
+ },
+};
+
+static struct platform_device bf54x_spi_master1 = {
+ .name = "bfin-spi",
+ .id = 1, /* Bus number */
+ .num_resources = ARRAY_SIZE(bfin_spi1_resource),
+ .resource = bfin_spi1_resource,
+ .dev = {
+ .platform_data = &bf54x_spi_master_info, /* Passed to driver */
+ },
+};
+#endif /* spi master and devices */
+
+#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+static struct resource bfin_twi0_resource[] = {
+ [0] = {
+ .start = TWI0_REGBASE,
+ .end = TWI0_REGBASE + 0xFF,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = IRQ_TWI0,
+ .end = IRQ_TWI0,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device i2c_bfin_twi0_device = {
+ .name = "i2c-bfin-twi",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(bfin_twi0_resource),
+ .resource = bfin_twi0_resource,
+};
+
+static struct resource bfin_twi1_resource[] = {
+ [0] = {
+ .start = TWI1_REGBASE,
+ .end = TWI1_REGBASE + 0xFF,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = IRQ_TWI1,
+ .end = IRQ_TWI1,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device i2c_bfin_twi1_device = {
+ .name = "i2c-bfin-twi",
+ .id = 1,
+ .num_resources = ARRAY_SIZE(bfin_twi1_resource),
+ .resource = bfin_twi1_resource,
+};
+#endif
+
static struct platform_device *ezkit_devices[] __initdata = {
#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
&rtc_device,
#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
&bfin_uart_device,
#endif
+
+#if defined(CONFIG_FB_BF54X_LQ043) || defined(CONFIG_FB_BF54X_LQ043_MODULE)
+ &bf54x_lq043_device,
+#endif
+
+#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
+ &smsc911x_device,
+#endif
+
+#if defined(CONFIG_USB_BF54x_HCD) || defined(CONFIG_USB_BF54x_HCD_MODULE)
+ &bf54x_hcd,
+#endif
+
+#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+ &musb_device,
+#endif
+
+#if defined(CONFIG_PATA_BF54X) || defined(CONFIG_PATA_BF54X_MODULE)
+ &bfin_atapi_device,
+#endif
+
+#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
+ &bf5xx_nand_device,
+#endif
+
+#if defined(CONFIG_SDH_BFIN) || defined(CONFIG_SDH_BFIN)
+ &bf54x_sdh_device,
+#endif
+
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+ &bf54x_spi_master0,
+/* &bf54x_spi_master1,*/
+#endif
+
+#if defined(CONFIG_KEYBOARD_BFIN) || defined(CONFIG_KEYBOARD_BFIN_MODULE)
+ &bf54x_kpad_device,
+#endif
+
+#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+ &i2c_bfin_twi0_device,
+ &i2c_bfin_twi1_device,
+#endif
};
static int __init stamp_init(void)
{
printk(KERN_INFO "%s(): registering device resources\n", __FUNCTION__);
platform_add_devices(ezkit_devices, ARRAY_SIZE(ezkit_devices));
+
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+ spi_register_board_info(bf54x_spi_board_info,
+ ARRAY_SIZE(bf54x_spi_board_info));
+#endif
+
return 0;
}
+++ /dev/null
-/*
- * File: arch/blackfin/mach-bf548/gpio.c
- * Based on:
- * Author: Michael Hennerich (hennerich@blackfin.uclinux.org)
- *
- * Created:
- * Description: GPIO Abstraction Layer
- *
- * Modified:
- * Copyright 2007 Analog Devices Inc.
- *
- * Bugs: Enter bugs at http://blackfin.uclinux.org/
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, see the file COPYING, or write
- * to the Free Software Foundation, Inc.,
- * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
- */
-
-#include <linux/module.h>
-#include <linux/err.h>
-#include <asm/blackfin.h>
-#include <asm/gpio.h>
-#include <asm/portmux.h>
-#include <linux/irq.h>
-
-static struct gpio_port_t *gpio_array[gpio_bank(MAX_BLACKFIN_GPIOS)] = {
- (struct gpio_port_t *)PORTA_FER,
- (struct gpio_port_t *)PORTB_FER,
- (struct gpio_port_t *)PORTC_FER,
- (struct gpio_port_t *)PORTD_FER,
- (struct gpio_port_t *)PORTE_FER,
- (struct gpio_port_t *)PORTF_FER,
- (struct gpio_port_t *)PORTG_FER,
- (struct gpio_port_t *)PORTH_FER,
- (struct gpio_port_t *)PORTI_FER,
- (struct gpio_port_t *)PORTJ_FER,
-};
-
-static unsigned short reserved_gpio_map[gpio_bank(MAX_BLACKFIN_GPIOS)];
-static unsigned short reserved_peri_map[gpio_bank(MAX_BLACKFIN_GPIOS)];
-
-inline int check_gpio(unsigned short gpio)
-{
- if (gpio == GPIO_PB15 || gpio == GPIO_PC14 || gpio == GPIO_PC15
- || gpio == GPIO_PH14 || gpio == GPIO_PH15
- || gpio == GPIO_PJ14 || gpio == GPIO_PJ15
- || gpio > MAX_BLACKFIN_GPIOS)
- return -EINVAL;
- return 0;
-}
-
-inline void portmux_setup(unsigned short portno, unsigned short function)
-{
- u32 pmux;
-
- pmux = gpio_array[gpio_bank(portno)]->port_mux;
-
- pmux &= ~(0x3 << (2 * gpio_sub_n(portno)));
- pmux |= (function & 0x3) << (2 * gpio_sub_n(portno));
-
- gpio_array[gpio_bank(portno)]->port_mux = pmux;
-
-}
-
-inline u16 get_portmux(unsigned short portno)
-{
- u32 pmux;
-
- pmux = gpio_array[gpio_bank(portno)]->port_mux;
-
- return (pmux >> (2 * gpio_sub_n(portno)) & 0x3);
-
-}
-
-static void port_setup(unsigned short gpio, unsigned short usage)
-{
- if (usage == GPIO_USAGE) {
- if (gpio_array[gpio_bank(gpio)]->port_fer & gpio_bit(gpio))
- printk(KERN_WARNING
- "bfin-gpio: Possible Conflict with Peripheral "
- "usage and GPIO %d detected!\n", gpio);
- gpio_array[gpio_bank(gpio)]->port_fer &= ~gpio_bit(gpio);
- } else
- gpio_array[gpio_bank(gpio)]->port_fer |= gpio_bit(gpio);
- SSYNC();
-}
-
-static int __init bfin_gpio_init(void)
-{
- printk(KERN_INFO "Blackfin GPIO Controller\n");
-
- return 0;
-}
-
-arch_initcall(bfin_gpio_init);
-
-int peripheral_request(unsigned short per, const char *label)
-{
- unsigned long flags;
- unsigned short ident = P_IDENT(per);
-
- if (!(per & P_DEFINED))
- return -ENODEV;
-
- if (check_gpio(ident) < 0)
- return -EINVAL;
-
- local_irq_save(flags);
-
- if (unlikely(reserved_gpio_map[gpio_bank(ident)] & gpio_bit(ident))) {
- printk(KERN_ERR
- "%s: Peripheral %d is already reserved as GPIO!\n",
- __FUNCTION__, per);
- dump_stack();
- local_irq_restore(flags);
- return -EBUSY;
- }
-
- if (unlikely(reserved_peri_map[gpio_bank(ident)] & gpio_bit(ident))) {
-
- u16 funct = get_portmux(ident);
-
- if (!((per & P_MAYSHARE) && (funct == P_FUNCT2MUX(per)))) {
- printk(KERN_ERR
- "%s: Peripheral %d is already reserved!\n",
- __FUNCTION__, per);
- dump_stack();
- local_irq_restore(flags);
- return -EBUSY;
- }
- }
-
- reserved_peri_map[gpio_bank(ident)] |= gpio_bit(ident);
-
- portmux_setup(ident, P_FUNCT2MUX(per));
- port_setup(ident, PERIPHERAL_USAGE);
-
- local_irq_restore(flags);
-
- return 0;
-}
-EXPORT_SYMBOL(peripheral_request);
-
-int peripheral_request_list(unsigned short per[], const char *label)
-{
-
- u16 cnt;
- int ret;
-
- for (cnt = 0; per[cnt] != 0; cnt++) {
- ret = peripheral_request(per[cnt], label);
- if (ret < 0)
- return ret;
- }
-
- return 0;
-}
-EXPORT_SYMBOL(peripheral_request_list);
-
-void peripheral_free(unsigned short per)
-{
- unsigned long flags;
- unsigned short ident = P_IDENT(per);
-
- if (!(per & P_DEFINED))
- return;
-
- if (check_gpio(ident) < 0)
- return;
-
- local_irq_save(flags);
-
- if (unlikely(!(reserved_peri_map[gpio_bank(ident)] & gpio_bit(ident)))) {
- printk(KERN_ERR "bfin-gpio: Peripheral %d wasn't reserved!\n", per);
- dump_stack();
- local_irq_restore(flags);
- return;
- }
-
- if (!(per & P_MAYSHARE)) {
- port_setup(ident, GPIO_USAGE);
- }
-
- reserved_peri_map[gpio_bank(ident)] &= ~gpio_bit(ident);
-
- local_irq_restore(flags);
-}
-EXPORT_SYMBOL(peripheral_free);
-
-void peripheral_free_list(unsigned short per[])
-{
- u16 cnt;
-
- for (cnt = 0; per[cnt] != 0; cnt++) {
- peripheral_free(per[cnt]);
- }
-
-}
-EXPORT_SYMBOL(peripheral_free_list);
-
-/***********************************************************
-*
-* FUNCTIONS: Blackfin GPIO Driver
-*
-* INPUTS/OUTPUTS:
-* gpio - GPIO Number between 0 and MAX_BLACKFIN_GPIOS
-*
-*
-* DESCRIPTION: Blackfin GPIO Driver API
-*
-* CAUTION:
-*************************************************************
-* MODIFICATION HISTORY :
-**************************************************************/
-
-int gpio_request(unsigned short gpio, const char *label)
-{
- unsigned long flags;
-
- if (check_gpio(gpio) < 0)
- return -EINVAL;
-
- local_irq_save(flags);
-
- if (unlikely(reserved_gpio_map[gpio_bank(gpio)] & gpio_bit(gpio))) {
- printk(KERN_ERR "bfin-gpio: GPIO %d is already reserved!\n", gpio);
- dump_stack();
- local_irq_restore(flags);
- return -EBUSY;
- }
-
- if (unlikely(reserved_peri_map[gpio_bank(gpio)] & gpio_bit(gpio))) {
- printk(KERN_ERR
- "bfin-gpio: GPIO %d is already reserved as Peripheral!\n", gpio);
- dump_stack();
- local_irq_restore(flags);
- return -EBUSY;
- }
-
- reserved_gpio_map[gpio_bank(gpio)] |= gpio_bit(gpio);
-
- local_irq_restore(flags);
-
- port_setup(gpio, GPIO_USAGE);
-
- return 0;
-}
-EXPORT_SYMBOL(gpio_request);
-
-void gpio_free(unsigned short gpio)
-{
- unsigned long flags;
-
- if (check_gpio(gpio) < 0)
- return;
-
- local_irq_save(flags);
-
- if (unlikely(!(reserved_gpio_map[gpio_bank(gpio)] & gpio_bit(gpio)))) {
- printk(KERN_ERR "bfin-gpio: GPIO %d wasn't reserved!\n", gpio);
- dump_stack();
- local_irq_restore(flags);
- return;
- }
-
- reserved_gpio_map[gpio_bank(gpio)] &= ~gpio_bit(gpio);
-
- local_irq_restore(flags);
-}
-EXPORT_SYMBOL(gpio_free);
-
-void gpio_direction_input(unsigned short gpio)
-{
- unsigned long flags;
-
- BUG_ON(!(reserved_gpio_map[gpio_bank(gpio)] & gpio_bit(gpio)));
-
- local_irq_save(flags);
- gpio_array[gpio_bank(gpio)]->port_dir_clear = gpio_bit(gpio);
- gpio_array[gpio_bank(gpio)]->port_inen |= gpio_bit(gpio);
- local_irq_restore(flags);
-}
-EXPORT_SYMBOL(gpio_direction_input);
-
-void gpio_direction_output(unsigned short gpio)
-{
- unsigned long flags;
-
- BUG_ON(!(reserved_gpio_map[gpio_bank(gpio)] & gpio_bit(gpio)));
-
- local_irq_save(flags);
- gpio_array[gpio_bank(gpio)]->port_inen &= ~gpio_bit(gpio);
- gpio_array[gpio_bank(gpio)]->port_dir_set = gpio_bit(gpio);
- local_irq_restore(flags);
-}
-EXPORT_SYMBOL(gpio_direction_output);
-
-void gpio_set_value(unsigned short gpio, unsigned short arg)
-{
- if (arg)
- gpio_array[gpio_bank(gpio)]->port_set = gpio_bit(gpio);
- else
- gpio_array[gpio_bank(gpio)]->port_clear = gpio_bit(gpio);
-
-}
-EXPORT_SYMBOL(gpio_set_value);
-
-unsigned short gpio_get_value(unsigned short gpio)
-{
- return (1 & (gpio_array[gpio_bank(gpio)]->port_data >> gpio_sub_n(gpio)));
-}
-EXPORT_SYMBOL(gpio_get_value);
#include <asm/blackfin.h>
#include <asm/trace.h>
#if CONFIG_BFIN_KERNEL_CLOCK
+#include <asm/mach-common/clocks.h>
#include <asm/mach/mem_init.h>
#endif
ENTRY(__stext)
/* R0: argument of command line string, passed from uboot, save it */
R7 = R0;
- /* Set the SYSCFG register */
- R0 = 0x36;
- SYSCFG = R0; /*Enable Cycle Counter and Nesting Of Interrupts(3rd Bit)*/
+ /* Enable Cycle Counter and Nesting Of Interrupts */
+#ifdef CONFIG_BFIN_SCRATCH_REG_CYCLES
+ R0 = SYSCFG_SNEN;
+#else
+ R0 = SYSCFG_SNEN | SYSCFG_CCEN;
+#endif
+ SYSCFG = R0;
R0 = 0;
/* Clear Out All the data and pointer Registers*/
M2 = r0;
M3 = r0;
- trace_buffer_start(p0,r0);
+ trace_buffer_init(p0,r0);
P0 = R1;
R0 = R1;
/* Turn off the icache */
- p0.l = (IMEM_CONTROL & 0xFFFF);
- p0.h = (IMEM_CONTROL >> 16);
+ p0.l = LO(IMEM_CONTROL);
+ p0.h = HI(IMEM_CONTROL);
R1 = [p0];
R0 = ~ENICPLB;
R0 = R0 & R1;
SSYNC;
/* Turn off the dcache */
- p0.l = (DMEM_CONTROL & 0xFFFF);
- p0.h = (DMEM_CONTROL >> 16);
+ p0.l = LO(DMEM_CONTROL);
+ p0.h = HI(DMEM_CONTROL);
R1 = [p0];
R0 = ~ENDCPLB;
R0 = R0 & R1;
FP = SP;
USP = SP;
+#ifdef CONFIG_EARLY_PRINTK
+ SP += -12;
+ call _init_early_exception_vectors;
+ SP += 12;
+#endif
+
/* Put The Code for PLL Programming and SDRAM Programming in L1 ISRAM */
call _bf53x_relocate_l1_mem;
#if CONFIG_BFIN_KERNEL_CLOCK
p0.l = .LWAIT_HERE;
p0.h = .LWAIT_HERE;
reti = p0;
-#if defined (ANOMALY_05000281)
+#if ANOMALY_05000281
nop;
nop;
nop;
w[p0] = r0.l;
ssync;
- p0.l = (EBIU_SDBCTL & 0xFFFF);
- p0.h = (EBIU_SDBCTL >> 16); /* SDRAM Memory Bank Control Register */
+ p0.l = LO(EBIU_SDBCTL);
+ p0.h = HI(EBIU_SDBCTL); /* SDRAM Memory Bank Control Register */
r0 = mem_SDBCTL;
w[p0] = r0.l;
ssync;
RTS;
#endif /* CONFIG_BFIN_KERNEL_CLOCK */
-ENTRY(_bfin_reset)
- /* No more interrupts to be handled*/
- CLI R6;
- SSYNC;
-
-#if defined(CONFIG_MTD_M25P80)
-/*
- * The following code fix the SPI flash reboot issue,
- * /CS signal of the chip which is using PF10 return to GPIO mode
- */
- p0.h = hi(PORTF_FER);
- p0.l = lo(PORTF_FER);
- r0.l = 0x0000;
- w[p0] = r0.l;
- SSYNC;
-
-/* /CS return to high */
- p0.h = hi(PORTFIO);
- p0.l = lo(PORTFIO);
- r0.l = 0xFFFF;
- w[p0] = r0.l;
- SSYNC;
-
-/* Delay some time, This is necessary */
- r1.h = 0;
- r1.l = 0x400;
- p1 = r1;
- lsetup (_delay_lab1,_delay_lab1_end ) lc1 = p1;
-_delay_lab1:
- r0.h = 0;
- r0.l = 0x8000;
- p0 = r0;
- lsetup (_delay_lab0,_delay_lab0_end ) lc0 = p0;
-_delay_lab0:
- nop;
-_delay_lab0_end:
- nop;
-_delay_lab1_end:
- nop;
-#endif
-
- /* Clear the bits 13-15 in SWRST if they werent cleared */
- p0.h = hi(SWRST);
- p0.l = lo(SWRST);
- csync;
- r0.l = w[p0];
-
- /* Clear the IMASK register */
- p0.h = hi(IMASK);
- p0.l = lo(IMASK);
- r0 = 0x0;
- [p0] = r0;
-
- /* Clear the ILAT register */
- p0.h = hi(ILAT);
- p0.l = lo(ILAT);
- r0 = [p0];
- [p0] = r0;
- SSYNC;
-
- /* Disable the WDOG TIMER */
- p0.h = hi(WDOG_CTL);
- p0.l = lo(WDOG_CTL);
- r0.l = 0xAD6;
- w[p0] = r0.l;
- SSYNC;
-
- /* Clear the sticky bit incase it is already set */
- p0.h = hi(WDOG_CTL);
- p0.l = lo(WDOG_CTL);
- r0.l = 0x8AD6;
- w[p0] = r0.l;
- SSYNC;
-
- /* Program the count value */
- R0.l = 0x100;
- R0.h = 0x0;
- P0.h = hi(WDOG_CNT);
- P0.l = lo(WDOG_CNT);
- [P0] = R0;
- SSYNC;
-
- /* Program WDOG_STAT if necessary */
- P0.h = hi(WDOG_CTL);
- P0.l = lo(WDOG_CTL);
- R0 = W[P0](Z);
- CC = BITTST(R0,1);
- if !CC JUMP .LWRITESTAT;
- CC = BITTST(R0,2);
- if !CC JUMP .LWRITESTAT;
- JUMP .LSKIP_WRITE;
-
-.LWRITESTAT:
- /* When watch dog timer is enabled,
- * a write to STAT will load the contents of CNT to STAT
- */
- R0 = 0x0000(z);
- P0.h = hi(WDOG_STAT);
- P0.l = lo(WDOG_STAT)
- [P0] = R0;
- SSYNC;
-
-.LSKIP_WRITE:
- /* Enable the reset event */
- P0.h = hi(WDOG_CTL);
- P0.l = lo(WDOG_CTL);
- R0 = W[P0](Z);
- BITCLR(R0,1);
- BITCLR(R0,2);
- W[P0] = R0.L;
- SSYNC;
- NOP;
-
- /* Enable the wdog counter */
- R0 = W[P0](Z);
- BITCLR(R0,4);
- W[P0] = R0.L;
- SSYNC;
-
- IDLE;
-
- RTS;
-
.data
/*
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
#include <linux/usb_isp1362.h>
+#include <linux/pata_platform.h>
#include <linux/irq.h>
+#include <asm/dma.h>
#include <asm/bfin5xx_spi.h>
/*
/* the modalias must be the same as spi device driver name */
.modalias = "m25p80", /* Name of spi_driver for this device */
.max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1, /* Framework bus number */
+ .bus_num = 0, /* Framework bus number */
.chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/
.platform_data = &bfin_spi_flash_data,
.controller_data = &spi_flash_chip_info,
{
.modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
.max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1, /* Framework bus number */
+ .bus_num = 0, /* Framework bus number */
.chip_select = 1, /* Framework chip select. */
.platform_data = NULL, /* No spi_driver specific config */
.controller_data = &spi_adc_chip_info,
{
.modalias = "ad1836-spi",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1,
+ .bus_num = 0,
.chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
.controller_data = &ad1836_spi_chip_info,
},
{
.modalias = "ad9960-spi",
.max_speed_hz = 10000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1,
+ .bus_num = 0,
.chip_select = 1,
.controller_data = &ad9960_spi_chip_info,
},
{
.modalias = "spi_mmc",
.max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1,
+ .bus_num = 0,
.chip_select = CONFIG_SPI_MMC_CS_CHAN,
.platform_data = NULL,
.controller_data = &spi_mmc_chip_info,
#endif
};
+/* SPI (0) */
+static struct resource bfin_spi0_resource[] = {
+ [0] = {
+ .start = SPI0_REGBASE,
+ .end = SPI0_REGBASE + 0xFF,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = CH_SPI,
+ .end = CH_SPI,
+ .flags = IORESOURCE_IRQ,
+ }
+};
+
/* SPI controller data */
-static struct bfin5xx_spi_master spi_bfin_master_info = {
+static struct bfin5xx_spi_master bfin_spi0_info = {
.num_chipselect = 8,
.enable_dma = 1, /* master has the ability to do dma transfer */
};
-static struct platform_device spi_bfin_master_device = {
- .name = "bfin-spi-master",
- .id = 1, /* Bus number */
+static struct platform_device bfin_spi0_device = {
+ .name = "bfin-spi",
+ .id = 0, /* Bus number */
+ .num_resources = ARRAY_SIZE(bfin_spi0_resource),
+ .resource = bfin_spi0_resource,
.dev = {
- .platform_data = &spi_bfin_master_info, /* Passed to driver */
+ .platform_data = &bfin_spi0_info, /* Passed to driver */
},
};
#endif /* spi master and devices */
};
#endif
+#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+#define PATA_INT 119
+
+static struct pata_platform_info bfin_pata_platform_data = {
+ .ioport_shift = 2,
+ .irq_type = IRQF_TRIGGER_HIGH | IRQF_DISABLED,
+};
+
+static struct resource bfin_pata_resources[] = {
+ {
+ .start = 0x2400C000,
+ .end = 0x2400C001F,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = 0x2400D018,
+ .end = 0x2400D01B,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = PATA_INT,
+ .end = PATA_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device bfin_pata_device = {
+ .name = "pata_platform",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(bfin_pata_resources),
+ .resource = bfin_pata_resources,
+ .dev = {
+ .platform_data = &bfin_pata_platform_data,
+ }
+};
+#endif
+
static struct platform_device *cm_bf561_devices[] __initdata = {
#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
#endif
#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
- &spi_bfin_master_device,
+ &bfin_spi0_device,
#endif
+#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+ &bfin_pata_device,
+#endif
};
static int __init cm_bf561_init(void)
#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
#endif
+
+#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+ irq_desc[PATA_INT].status |= IRQ_NOAUTOEN;
+#endif
return 0;
}
#include <linux/spi/spi.h>
#include <linux/irq.h>
#include <linux/interrupt.h>
+#include <linux/pata_platform.h>
+#include <asm/dma.h>
#include <asm/bfin5xx_spi.h>
/*
#endif
#endif
+/* SPI (0) */
+static struct resource bfin_spi0_resource[] = {
+ [0] = {
+ .start = SPI0_REGBASE,
+ .end = SPI0_REGBASE + 0xFF,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = CH_SPI,
+ .end = CH_SPI,
+ .flags = IORESOURCE_IRQ,
+ }
+};
+
/* SPI controller data */
-static struct bfin5xx_spi_master spi_bfin_master_info = {
+static struct bfin5xx_spi_master bfin_spi0_info = {
.num_chipselect = 8,
.enable_dma = 1, /* master has the ability to do dma transfer */
};
-static struct platform_device spi_bfin_master_device = {
- .name = "bfin-spi-master",
- .id = 1, /* Bus number */
+static struct platform_device bfin_spi0_device = {
+ .name = "bfin-spi",
+ .id = 0, /* Bus number */
+ .num_resources = ARRAY_SIZE(bfin_spi0_resource),
+ .resource = bfin_spi0_resource,
.dev = {
- .platform_data = &spi_bfin_master_info, /* Passed to driver */
+ .platform_data = &bfin_spi0_info, /* Passed to driver */
},
};
{
.modalias = "ad1836-spi",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1,
+ .bus_num = 0,
.chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
.controller_data = &ad1836_spi_chip_info,
},
#endif
};
+#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+#define PATA_INT 55
+
+static struct pata_platform_info bfin_pata_platform_data = {
+ .ioport_shift = 1,
+ .irq_type = IRQF_TRIGGER_HIGH | IRQF_DISABLED,
+};
+
+static struct resource bfin_pata_resources[] = {
+ {
+ .start = 0x20314020,
+ .end = 0x2031403F,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = 0x2031401C,
+ .end = 0x2031401F,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = PATA_INT,
+ .end = PATA_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device bfin_pata_device = {
+ .name = "pata_platform",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(bfin_pata_resources),
+ .resource = bfin_pata_resources,
+ .dev = {
+ .platform_data = &bfin_pata_platform_data,
+ }
+};
+#endif
+
static struct platform_device *ezkit_devices[] __initdata = {
#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
&smc91x_device,
#endif
#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
- &spi_bfin_master_device,
+ &bfin_spi0_device,
#endif
#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
&bfin_uart_device,
#endif
+#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+ &bfin_pata_device,
+#endif
};
static int __init ezkit_init(void)
SSYNC();
#endif
- return spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+ spi_register_board_info(bfin_spi_board_info,
+ ARRAY_SIZE(bfin_spi_board_info));
+#endif
+
+#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+ irq_desc[PATA_INT].status |= IRQ_NOAUTOEN;
+#endif
+ return 0;
}
arch_initcall(ezkit_init);
#include <asm/trace.h>
#if CONFIG_BFIN_KERNEL_CLOCK
+#include <asm/mach-common/clocks.h>
#include <asm/mach/mem_init.h>
#endif
ENTRY(__start)
/* R0: argument of command line string, passed from uboot, save it */
R7 = R0;
- /* Set the SYSCFG register:
- * Enable Cycle Counter and Nesting Of Interrupts (3rd Bit)
- */
- R0 = 0x36;
+ /* Enable Cycle Counter and Nesting Of Interrupts */
+#ifdef CONFIG_BFIN_SCRATCH_REG_CYCLES
+ R0 = SYSCFG_SNEN;
+#else
+ R0 = SYSCFG_SNEN | SYSCFG_CCEN;
+#endif
SYSCFG = R0;
R0 = 0;
M2 = r0;
M3 = r0;
- trace_buffer_start(p0,r0);
+ trace_buffer_init(p0,r0);
P0 = R1;
R0 = R1;
/* Turn off the icache */
- p0.l = (IMEM_CONTROL & 0xFFFF);
- p0.h = (IMEM_CONTROL >> 16);
+ p0.l = LO(IMEM_CONTROL);
+ p0.h = HI(IMEM_CONTROL);
R1 = [p0];
R0 = ~ENICPLB;
R0 = R0 & R1;
- /* Anomaly 05000125 */
-#ifdef ANOMALY_05000125
+#if ANOMALY_05000125
CLI R2;
SSYNC;
#endif
[p0] = R0;
SSYNC;
-#ifdef ANOMALY_05000125
+#if ANOMALY_05000125
STI R2;
#endif
/* Turn off the dcache */
- p0.l = (DMEM_CONTROL & 0xFFFF);
- p0.h = (DMEM_CONTROL >> 16);
+ p0.l = LO(DMEM_CONTROL);
+ p0.h = HI(DMEM_CONTROL);
R1 = [p0];
R0 = ~ENDCPLB;
R0 = R0 & R1;
/* Anomaly 05000125 */
-#ifdef ANOMALY_05000125
+#if ANOMALY_05000125
CLI R2;
SSYNC;
#endif
[p0] = R0;
SSYNC;
-#ifdef ANOMALY_05000125
+#if ANOMALY_05000125
STI R2;
#endif
fp = sp;
usp = sp;
+#ifdef CONFIG_EARLY_PRINTK
+ SP += -12;
+ call _init_early_exception_vectors;
+ SP += 12;
+#endif
+
/* Put The Code for PLL Programming and SDRAM Programming in L1 ISRAM */
call _bf53x_relocate_l1_mem;
#if CONFIG_BFIN_KERNEL_CLOCK
p0.l = .LWAIT_HERE;
p0.h = .LWAIT_HERE;
reti = p0;
-#if defined(ANOMALY_05000281)
+#if ANOMALY_05000281
nop; nop; nop;
#endif
rti;
w[p0] = r0.l;
ssync;
- p0.l = (EBIU_SDBCTL & 0xFFFF);
- p0.h = (EBIU_SDBCTL >> 16); /* SDRAM Memory Bank Control Register */
+ p0.l = LO(EBIU_SDBCTL);
+ p0.h = HI(EBIU_SDBCTL); /* SDRAM Memory Bank Control Register */
r0 = mem_SDBCTL;
w[p0] = r0.l;
ssync;
ENDPROC(_start_dma_code)
#endif /* CONFIG_BFIN_KERNEL_CLOCK */
-ENTRY(_bfin_reset)
- /* No more interrupts to be handled*/
- CLI R6;
- SSYNC;
-
-#if defined(CONFIG_BFIN_SHARED_FLASH_ENET)
- p0.h = hi(FIO_INEN);
- p0.l = lo(FIO_INEN);
- r0.l = ~(PF1 | PF0);
- w[p0] = r0.l;
-
- p0.h = hi(FIO_DIR);
- p0.l = lo(FIO_DIR);
- r0.l = (PF1 | PF0);
- w[p0] = r0.l;
-
- p0.h = hi(FIO_FLAG_C);
- p0.l = lo(FIO_FLAG_C);
- r0.l = (PF1 | PF0);
- w[p0] = r0.l;
-#endif
-
- /* Clear the IMASK register */
- p0.h = hi(IMASK);
- p0.l = lo(IMASK);
- r0 = 0x0;
- [p0] = r0;
-
- /* Clear the ILAT register */
- p0.h = hi(ILAT);
- p0.l = lo(ILAT);
- r0 = [p0];
- [p0] = r0;
- SSYNC;
-
- /* make sure SYSCR is set to use BMODE */
- P0.h = hi(SYSCR);
- P0.l = lo(SYSCR);
- R0.l = 0x20; /* on BF561, disable core b */
- W[P0] = R0.l;
- SSYNC;
-
- /* issue a system soft reset */
- P1.h = hi(SWRST);
- P1.l = lo(SWRST);
- R1.l = 0x0007;
- W[P1] = R1;
- SSYNC;
-
- /* clear system soft reset */
- R0.l = 0x0000;
- W[P0] = R0;
- SSYNC;
-
- /* issue core reset */
- raise 1;
-
- RTS;
-ENDPROC(_bfin_reset)
-
.data
/*
obj-y := \
cache.o cacheinit.o cplbhdlr.o cplbmgr.o entry.o \
- interrupt.o lock.o irqpanic.o
+ interrupt.o lock.o irqpanic.o arch_checks.o
obj-$(CONFIG_CPLB_INFO) += cplbinfo.o
obj-$(CONFIG_BFIN_SINGLE_CORE) += ints-priority-sc.o
--- /dev/null
+/*
+ * File: arch/blackfin/mach-common/arch_checks.c
+ * Based on:
+ * Author: Robin Getz <rgetz@blackfin.uclinux.org>
+ *
+ * Created: 25Jul07
+ * Description: Do some checking to make sure things are OK
+ *
+ * Modified:
+ * Copyright 2004-2007 Analog Devices Inc.
+ *
+ * Bugs: Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see the file COPYING, or write
+ * to the Free Software Foundation, Inc.,
+ * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <asm/mach/anomaly.h>
+#include <asm/mach-common/clocks.h>
+
+#ifdef CONFIG_BFIN_KERNEL_CLOCK
+
+# if (CONFIG_VCO_HZ > CONFIG_MAX_VCO_HZ)
+# error "VCO selected is more than maximum value. Please change the VCO multipler"
+# endif
+
+# if (CONFIG_SCLK_HZ > CONFIG_MAX_SCLK_HZ)
+# error "Sclk value selected is more than maximum. Please select a proper value for SCLK multiplier"
+# endif
+
+# if (CONFIG_SCLK_HZ < CONFIG_MIN_SCLK_HZ)
+# error "Sclk value selected is less than minimum. Please select a proper value for SCLK multiplier"
+# endif
+
+# if (ANOMALY_05000273) && (CONFIG_SCLK_HZ * 2 > CONFIG_CCLK_HZ)
+# error "ANOMALY 05000273, please make sure CCLK is at least 2x SCLK"
+# endif
+
+# if (CONFIG_SCLK_HZ > CONFIG_CCLK_HZ) && (CONFIG_SCLK_HZ != CONFIG_CLKIN_HZ) && (CONFIG_CCLK_HZ != CONFIG_CLKIN_HZ)
+# error "Please select sclk less than cclk"
+# endif
+
+#endif /* CONFIG_BFIN_KERNEL_CLOCK */
+
+#if (CONFIG_MEM_SIZE % 4)
+#error "SDRAM mem size must be multible of 4MB"
+#endif
+
ENTRY(_invalidate_entire_icache)
[--SP] = ( R7:5);
- P0.L = (IMEM_CONTROL & 0xFFFF);
- P0.H = (IMEM_CONTROL >> 16);
+ P0.L = LO(IMEM_CONTROL);
+ P0.H = HI(IMEM_CONTROL);
R7 = [P0];
/* Clear the IMC bit , All valid bits in the instruction
ENTRY(_dcache_invalidate)
[--SP] = ( R7:6);
- P0.L = (DMEM_CONTROL & 0xFFFF);
- P0.H = (DMEM_CONTROL >> 16);
+ P0.L = LO(DMEM_CONTROL);
+ P0.H = HI(DMEM_CONTROL);
R7 = [P0];
/* Clear the DMC[1:0] bits, All valid bits in the data
.text
-#ifdef ANOMALY_05000125
-#if defined(CONFIG_BLKFIN_CACHE)
+#if ANOMALY_05000125
+#if defined(CONFIG_BFIN_ICACHE)
ENTRY(_bfin_write_IMEM_CONTROL)
/* Enable Instruction Cache */
- P0.l = (IMEM_CONTROL & 0xFFFF);
- P0.h = (IMEM_CONTROL >> 16);
+ P0.l = LO(IMEM_CONTROL);
+ P0.h = HI(IMEM_CONTROL);
/* Anomaly 05000125 */
CLI R1;
ENDPROC(_bfin_write_IMEM_CONTROL)
#endif
-#if defined(CONFIG_BLKFIN_DCACHE)
+#if defined(CONFIG_BFIN_DCACHE)
ENTRY(_bfin_write_DMEM_CONTROL)
- P0.l = (DMEM_CONTROL & 0xFFFF);
- P0.h = (DMEM_CONTROL >> 16);
+ P0.l = LO(DMEM_CONTROL);
+ P0.h = HI(DMEM_CONTROL);
CLI R1;
SSYNC; /* SSYNC required before writing to DMEM_CONTROL. */
.Lis_icplb_miss:
-#if defined(CONFIG_BLKFIN_CACHE) || defined(CONFIG_BLKFIN_DCACHE)
-# if defined(CONFIG_BLKFIN_CACHE) && !defined(CONFIG_BLKFIN_DCACHE)
+#if defined(CONFIG_BFIN_ICACHE) || defined(CONFIG_BFIN_DCACHE)
+# if defined(CONFIG_BFIN_ICACHE) && !defined(CONFIG_BFIN_DCACHE)
R1 = CPLB_ENABLE_ICACHE;
# endif
-# if !defined(CONFIG_BLKFIN_CACHE) && defined(CONFIG_BLKFIN_DCACHE)
+# if !defined(CONFIG_BFIN_ICACHE) && defined(CONFIG_BFIN_DCACHE)
R1 = CPLB_ENABLE_DCACHE;
# endif
-# if defined(CONFIG_BLKFIN_CACHE) && defined(CONFIG_BLKFIN_DCACHE)
+# if defined(CONFIG_BFIN_ICACHE) && defined(CONFIG_BFIN_DCACHE)
R1 = CPLB_ENABLE_DCACHE | CPLB_ENABLE_ICACHE;
# endif
#else
* from the configuration table.
*/
- P4.L = (ICPLB_FAULT_ADDR & 0xFFFF);
- P4.H = (ICPLB_FAULT_ADDR >> 16);
+ P4.L = LO(ICPLB_FAULT_ADDR);
+ P4.H = HI(ICPLB_FAULT_ADDR);
P1 = 16;
P5.L = _page_size_table;
P5.H = _page_size_table;
- P0.L = (ICPLB_DATA0 & 0xFFFF);
- P0.H = (ICPLB_DATA0 >> 16);
+ P0.L = LO(ICPLB_DATA0);
+ P0.H = HI(ICPLB_DATA0);
R4 = [P4]; /* Get faulting address*/
R6 = 64; /* Advance past the fault address, which*/
R6 = R6 + R4; /* we'll use if we find a match*/
I0 = R4; /* Fault address we'll search for*/
/* set up pointers */
- P0.L = (ICPLB_DATA0 & 0xFFFF);
- P0.H = (ICPLB_DATA0 >> 16);
+ P0.L = LO(ICPLB_DATA0);
+ P0.H = HI(ICPLB_DATA0);
/* The replacement procedure for ICPLBs */
- P4.L = (IMEM_CONTROL & 0xFFFF);
- P4.H = (IMEM_CONTROL >> 16);
+ P4.L = LO(IMEM_CONTROL);
+ P4.H = HI(IMEM_CONTROL);
/* disable cplbs */
R5 = [P4]; /* Control Register*/
* last entry of the table.
*/
- P1.L = (ICPLB_DATA15 & 0xFFFF); /* ICPLB_DATA15 */
- P1.H = (ICPLB_DATA15 >> 16);
+ P1.L = LO(ICPLB_DATA15); /* ICPLB_DATA15 */
+ P1.H = HI(ICPLB_DATA15);
[P1] = R2;
[P1-0x100] = R4;
#ifdef CONFIG_CPLB_INFO
* pending writes associated with the CPLB.
*/
- P4.L = (DCPLB_STATUS & 0xFFFF);
- P4.H = (DCPLB_STATUS >> 16);
- P3.L = (DCPLB_DATA0 & 0xFFFF);
- P3.H = (DCPLB_DATA0 >> 16);
+ P4.L = LO(DCPLB_STATUS);
+ P4.H = HI(DCPLB_STATUS);
+ P3.L = LO(DCPLB_DATA0);
+ P3.H = HI(DCPLB_DATA0);
R5 = [P4];
/* A protection violation can be caused by more than just writes
* config table, that covers the faulting address.
*/
- P1.L = (DCPLB_DATA15 & 0xFFFF);
- P1.H = (DCPLB_DATA15 >> 16);
+ P1.L = LO(DCPLB_DATA15);
+ P1.H = HI(DCPLB_DATA15);
- P4.L = (DCPLB_FAULT_ADDR & 0xFFFF);
- P4.H = (DCPLB_FAULT_ADDR >> 16);
+ P4.L = LO(DCPLB_FAULT_ADDR);
+ P4.H = HI(DCPLB_FAULT_ADDR);
R4 = [P4];
I0 = R4;
R6 = R1; /* Save for later*/
/* Turn off CPLBs while we work.*/
- P4.L = (DMEM_CONTROL & 0xFFFF);
- P4.H = (DMEM_CONTROL >> 16);
+ P4.L = LO(DMEM_CONTROL);
+ P4.H = HI(DMEM_CONTROL);
R5 = [P4];
BITCLR(R5,ENDCPLB_P);
CLI R0;
* are no good.
*/
- I1.L = (DCPLB_DATA0 & 0xFFFF);
- I1.H = (DCPLB_DATA0 >> 16);
+ I1.L = LO(DCPLB_DATA0);
+ I1.H = HI(DCPLB_DATA0);
P1 = 2;
P2 = 16;
I2.L = _dcplb_preference;
P3.L = _page_size_table; /* retrieve end address */
P3.H = _page_size_table; /* retrieve end address */
R3 = 0x1002; /* 16th - position, 2 bits -length */
-#ifdef ANOMALY_05000209
+#if ANOMALY_05000209
nop; /* Anomaly 05000209 */
#endif
R7 = EXTRACT(R1,R3.l);
* one space closer to the start.
*/
- R1.L = (DCPLB_DATA16 & 0xFFFF); /* DCPLB_DATA15 + 4 */
- R1.H = (DCPLB_DATA16 >> 16);
+ R1.L = LO(DCPLB_DATA16); /* DCPLB_DATA15 + 4 */
+ R1.H = HI(DCPLB_DATA16);
R0 = P0;
/* If the victim happens to be in DCPLB15,
* if necessary.
*/
- P1.L = (DCPLB_DATA15 & 0xFFFF);
- P1.H = (DCPLB_DATA15 >> 16);
+ P1.L = LO(DCPLB_DATA15);
+ P1.H = HI(DCPLB_DATA15);
/* If the DCPLB has cache bits set, but caching hasn't
* been enabled, then we want to mask off the cache-in-L1
* cost of first-write exceptions to mark the page as dirty.
*/
-#ifdef CONFIG_BLKFIN_WT
+#ifdef CONFIG_BFIN_WT
BITSET(R6, 14); /* Set WT*/
#endif
P0.H = hi(SICA_IWR1);
P0.L = lo(SICA_IWR1);
#else
- P0.h = (SIC_IWR >> 16);
- P0.l = (SIC_IWR & 0xFFFF);
+ P0.h = HI(SIC_IWR);
+ P0.l = LO(SIC_IWR);
#endif
R7 = [P0];
#if defined(CONFIG_BF561)
*/
R7 = 0x0000(z);
#if defined(CONFIG_BF561)
- P0.h = (WDOGA_STAT >> 16);
- P0.l = (WDOGA_STAT & 0xFFFF);
+ P0.h = HI(WDOGA_STAT);
+ P0.l = LO(WDOGA_STAT);
#else
- P0.h = (WDOG_STAT >> 16);
- P0.l = (WDOG_STAT & 0xFFFF);
+ P0.h = HI(WDOG_STAT);
+ P0.l = LO(WDOG_STAT);
#endif
[P0] = R7;
SSYNC;
ENTRY(_program_wdog_timer)
[--SP] = ( R7:0, P5:0 );
#if defined(CONFIG_BF561)
- P0.h = (WDOGA_CNT >> 16);
- P0.l = (WDOGA_CNT & 0xFFFF);
+ P0.h = HI(WDOGA_CNT);
+ P0.l = LO(WDOGA_CNT);
#else
- P0.h = (WDOG_CNT >> 16);
- P0.l = (WDOG_CNT & 0xFFFF);
+ P0.h = HI(WDOG_CNT);
+ P0.l = LO(WDOG_CNT);
#endif
[P0] = R0;
SSYNC;
#if defined(CONFIG_BF561)
- P0.h = (WDOGA_CTL >> 16);
- P0.l = (WDOGA_CTL & 0xFFFF);
+ P0.h = HI(WDOGA_CTL);
+ P0.l = LO(WDOGA_CTL);
#else
- P0.h = (WDOG_CTL >> 16);
- P0.l = (WDOG_CTL & 0xFFFF);
+ P0.h = HI(WDOG_CTL);
+ P0.l = LO(WDOG_CTL);
#endif
R7 = W[P0](Z);
CC = BITTST(R7,1);
.LSKIP_WRITE_TO_STAT:
#if defined(CONFIG_BF561)
- P0.h = (WDOGA_CTL >> 16);
- P0.l = (WDOGA_CTL & 0xFFFF);
+ P0.h = HI(WDOGA_CTL);
+ P0.l = LO(WDOGA_CTL);
#else
- P0.h = (WDOG_CTL >> 16);
- P0.l = (WDOG_CTL & 0xFFFF);
+ P0.h = HI(WDOG_CTL);
+ P0.l = LO(WDOG_CTL);
#endif
R7 = W[P0](Z);
BITCLR(R7,1); /* Enable GP event */
[--SP] = ( R7:0, P5:0 );
#if defined(CONFIG_BF561)
- P0.h = (WDOGA_CTL >> 16);
- P0.l = (WDOGA_CTL & 0xFFFF);
+ P0.h = HI(WDOGA_CTL);
+ P0.l = LO(WDOGA_CTL);
#else
- P0.h = (WDOG_CTL >> 16);
- P0.l = (WDOG_CTL & 0xFFFF);
+ P0.h = HI(WDOG_CTL);
+ P0.l = LO(WDOG_CTL);
#endif
R7 = 0x0AD6(Z);
W[P0] = R7.L;
ENTRY(_disable_wdog_timer)
[--SP] = ( R7:0, P5:0 );
#if defined(CONFIG_BF561)
- P0.h = (WDOGA_CTL >> 16);
- P0.l = (WDOGA_CTL & 0xFFFF);
+ P0.h = HI(WDOGA_CTL);
+ P0.l = LO(WDOGA_CTL);
#else
- P0.h = (WDOG_CTL >> 16);
- P0.l = (WDOG_CTL & 0xFFFF);
+ P0.h = HI(WDOG_CTL);
+ P0.l = LO(WDOG_CTL);
#endif
R7 = 0xAD6(Z);
W[P0] = R7.L;
P0.H = hi(PLL_CTL);
P0.L = lo(PLL_CTL);
R5 = W[P0](z);
- R0.L = (MIN_VC/CONFIG_CLKIN_HZ) << 9;
+ R0.L = (CONFIG_MIN_VCO_HZ/CONFIG_CLKIN_HZ) << 9;
W[P0] = R0.l;
SSYNC;
* 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*/
-/*
- * 25-Dec-2004 - LG Soft India
- * 1. Fix in return_from_int, to make sure any pending
- * system call in ILAT for this process to get
- * executed, otherwise in case context switch happens,
- * system call of first process (i.e in ILAT) will be
- * carried forward to the switched process.
- * 2. Removed Constant references for the following
- * a. IPEND
- * b. EXCAUSE mask
- * c. PAGE Mask
- */
-
-/*
- * NOTE: This code handles signal-recognition, which happens every time
+/* NOTE: This code handles signal-recognition, which happens every time
* after a timer-interrupt and after each system call.
*/
#include <asm/mach-common/context.S>
+#if defined(CONFIG_BFIN_SCRATCH_REG_RETN)
+# define EX_SCRATCH_REG RETN
+#elif defined(CONFIG_BFIN_SCRATCH_REG_RETE)
+# define EX_SCRATCH_REG RETE
+#else
+# define EX_SCRATCH_REG CYCLES
+#endif
+
+#if ANOMALY_05000281
+ENTRY(_safe_speculative_execution)
+ NOP;
+ NOP;
+ NOP;
+ jump _safe_speculative_execution;
+ENDPROC(_safe_speculative_execution)
+#endif
+
#ifdef CONFIG_EXCPT_IRQ_SYSC_L1
.section .l1.text
#else
* patch up CPLB misses on the kernel stack.
*/
ENTRY(_ex_dcplb)
-#if defined(ANOMALY_05000261)
+#if ANOMALY_05000261
/*
* Work around an anomaly: if we see a new DCPLB fault, return
* without doing anything. Then, if we get the same fault again,
call __cplb_hdr;
DEBUG_START_HWTRACE(p5, r7)
RESTORE_ALL_SYS
- SP = RETN;
+ SP = EX_SCRATCH_REG;
rtx;
ENDPROC(_ex_icplb)
(R7:6,P5:4) = [sp++];
ASTAT = [sp++];
raise 15; /* invoked by TRAP #0, for sys call */
- sp = retn;
+ sp = EX_SCRATCH_REG;
rtx
ENDPROC(_ex_syscall)
cc = r6 == r7;
if !cc jump _ex_trap_c;
-_return_from_exception:
+ENTRY(_return_from_exception)
DEBUG_START_HWTRACE(p5, r7)
-#ifdef ANOMALY_05000257
+#if ANOMALY_05000257
R7=LC0;
LC0=R7;
R7=LC1;
#endif
(R7:6,P5:4) = [sp++];
ASTAT = [sp++];
- sp = retn;
+ sp = EX_SCRATCH_REG;
rtx;
ENDPROC(_ex_soft_bp)
[--sp] = ASTAT;
[--sp] = (R7:6, P5:4);
+ENTRY(_ex_replaceable)
+ nop;
+
ENTRY(_ex_trap_c)
+ /* Make sure we are not in a double fault */
+ p4.l = lo(IPEND);
+ p4.h = hi(IPEND);
+ r7 = [p4];
+ CC = BITTST (r7, 5);
+ if CC jump _double_fault;
+
/* Call C code (trap_c) to handle the exception, which most
* likely involves sending a signal to the current process.
* To avoid double faults, lower our priority to IRQ5 first.
DEBUG_START_HWTRACE(p5, r7)
(R7:6,P5:4) = [sp++];
ASTAT = [sp++];
- SP = RETN;
+ SP = EX_SCRATCH_REG;
raise 5;
rtx;
ENDPROC(_ex_trap_c)
+/* We just realized we got an exception, while we were processing a different
+ * exception. This is a unrecoverable event, so crash
+ */
+ENTRY(_double_fault)
+ /* Turn caches & protection off, to ensure we don't get any more
+ * double exceptions
+ */
+
+ P4.L = LO(IMEM_CONTROL);
+ P4.H = HI(IMEM_CONTROL);
+
+ R5 = [P4]; /* Control Register*/
+ BITCLR(R5,ENICPLB_P);
+ SSYNC; /* SSYNC required before writing to IMEM_CONTROL. */
+ .align 8;
+ [P4] = R5;
+ SSYNC;
+
+ P4.L = LO(DMEM_CONTROL);
+ P4.H = HI(DMEM_CONTROL);
+ R5 = [P4];
+ BITCLR(R5,ENDCPLB_P);
+ SSYNC; /* SSYNC required before writing to DMEM_CONTROL. */
+ .align 8;
+ [P4] = R5;
+ SSYNC;
+
+ /* Fix up the stack */
+ (R7:6,P5:4) = [sp++];
+ ASTAT = [sp++];
+ SP = EX_SCRATCH_REG;
+
+ /* We should be out of the exception stack, and back down into
+ * kernel or user space stack
+ */
+ SAVE_ALL_SYS
+
+ r0 = sp; /* stack frame pt_regs pointer argument ==> r0 */
+ SP += -12;
+ call _double_fault_c;
+ SP += 12;
+.L_double_fault_panic:
+ JUMP .L_double_fault_panic
+
+ENDPROC(_double_fault)
+
ENTRY(_exception_to_level5)
SAVE_ALL_SYS
* covered by a CPLB. Switch to an exception stack; use RETN as a
* scratch register (for want of a better option).
*/
- retn = sp;
+ EX_SCRATCH_REG = sp;
sp.l = _exception_stack_top;
sp.h = _exception_stack_top;
/* Try to deal with syscalls quickly. */
r6.l = lo(SEQSTAT_EXCAUSE);
r6.h = hi(SEQSTAT_EXCAUSE);
r7 = r7 & r6;
- p5.h = _extable;
- p5.l = _extable;
+ p5.h = _ex_table;
+ p5.l = _ex_table;
p4 = r7;
p5 = p5 + (p4 << 2);
p4 = [p5];
p1.h = _schedule_and_signal_from_int;
[p0] = p1;
csync;
-#if defined(ANOMALY_05000281)
- r0.l = lo(CONFIG_BOOT_LOAD);
- r0.h = hi(CONFIG_BOOT_LOAD);
+#if ANOMALY_05000281
+ r0.l = _safe_speculative_execution;
+ r0.h = _safe_speculative_execution;
reti = r0;
#endif
r0 = 0x801f (z);
ENDPROC(_return_from_int)
ENTRY(_lower_to_irq14)
-#if defined(ANOMALY_05000281)
- r0.l = lo(CONFIG_BOOT_LOAD);
- r0.h = hi(CONFIG_BOOT_LOAD);
+#if ANOMALY_05000281
+ r0.l = _safe_speculative_execution;
+ r0.h = _safe_speculative_execution;
reti = r0;
#endif
r0 = 0x401f;
rts;
ENDPROC(_init_exception_buff)
+/* We handle this 100% in exception space - to reduce overhead
+ * Only potiential problem is if the software buffer gets swapped out of the
+ * CPLB table - then double fault. - so we don't let this happen in other places
+ */
+#ifdef CONFIG_DEBUG_BFIN_HWTRACE_EXPAND
+ENTRY(_ex_trace_buff_full)
+ [--sp] = P3;
+ [--sp] = P2;
+ [--sp] = LC0;
+ [--sp] = LT0;
+ [--sp] = LB0;
+ P5.L = _trace_buff_offset;
+ P5.H = _trace_buff_offset;
+ P3 = [P5]; /* trace_buff_offset */
+ P5.L = lo(TBUFSTAT);
+ P5.H = hi(TBUFSTAT);
+ R7 = [P5];
+ R7 <<= 1; /* double, since we need to read twice */
+ LC0 = R7;
+ R7 <<= 2; /* need to shift over again,
+ * to get the number of bytes */
+ P5.L = lo(TBUF);
+ P5.H = hi(TBUF);
+ R6 = ((1 << CONFIG_DEBUG_BFIN_HWTRACE_EXPAND_LEN)*1024) - 1;
+
+ P2 = R7;
+ P3 = P3 + P2;
+ R7 = P3;
+ R7 = R7 & R6;
+ P3 = R7;
+ P2.L = _trace_buff_offset;
+ P2.H = _trace_buff_offset;
+ [P2] = P3;
+
+ P2.L = _software_trace_buff;
+ P2.H = _software_trace_buff;
+
+ LSETUP (.Lstart, .Lend) LC0;
+.Lstart:
+ R7 = [P5]; /* read TBUF */
+ P4 = P3 + P2;
+ [P4] = R7;
+ P3 += -4;
+ R7 = P3;
+ R7 = R7 & R6;
+.Lend:
+ P3 = R7;
+
+ LB0 = [sp++];
+ LT0 = [sp++];
+ LC0 = [sp++];
+ P2 = [sp++];
+ P3 = [sp++];
+ jump _return_from_exception;
+ENDPROC(_ex_trace_buff_full)
+
+#if CONFIG_DEBUG_BFIN_HWTRACE_EXPAND_LEN == 4
+.data
+#else
+.section .l1.data.B
+#endif /* CONFIG_DEBUG_BFIN_HWTRACE_EXPAND_LEN */
+ENTRY(_trace_buff_offset)
+ .long 0;
+ALIGN
+ENTRY(_software_trace_buff)
+ .rept ((1 << CONFIG_DEBUG_BFIN_HWTRACE_EXPAND_LEN)*256);
+ .long 0
+ .endr
+#endif /* CONFIG_DEBUG_BFIN_HWTRACE_EXPAND */
+
+#if CONFIG_EARLY_PRINTK
+.section .init.text
+ENTRY(_early_trap)
+ SAVE_ALL_SYS
+ trace_buffer_stop(p0,r0);
+
+ /* Turn caches off, to ensure we don't get double exceptions */
+
+ P4.L = LO(IMEM_CONTROL);
+ P4.H = HI(IMEM_CONTROL);
+
+ R5 = [P4]; /* Control Register*/
+ BITCLR(R5,ENICPLB_P);
+ CLI R1;
+ SSYNC; /* SSYNC required before writing to IMEM_CONTROL. */
+ .align 8;
+ [P4] = R5;
+ SSYNC;
+
+ P4.L = LO(DMEM_CONTROL);
+ P4.H = HI(DMEM_CONTROL);
+ R5 = [P4];
+ BITCLR(R5,ENDCPLB_P);
+ SSYNC; /* SSYNC required before writing to DMEM_CONTROL. */
+ .align 8;
+ [P4] = R5;
+ SSYNC;
+ STI R1;
+
+ r0 = sp; /* stack frame pt_regs pointer argument ==> r0 */
+ r1 = RETX;
+
+ SP += -12;
+ call _early_trap_c;
+ SP += 12;
+ENDPROC(_early_trap)
+#endif /* CONFIG_EARLY_PRINTK */
+
/*
* Put these in the kernel data section - that should always be covered by
* a CPLB. This is needed to ensure we don't get double fault conditions
#else
.data
#endif
-ALIGN
-_extable:
+ENTRY(_ex_table)
/* entry for each EXCAUSE[5:0]
* This table must be in sync with the table in ./kernel/traps.c
* EXCPT instruction can provide 4 bits of EXCAUSE, allowing 16 to be user defined
*/
- .long _ex_syscall; /* 0x00 - User Defined - Linux Syscall */
+ .long _ex_syscall /* 0x00 - User Defined - Linux Syscall */
.long _ex_soft_bp /* 0x01 - User Defined - Software breakpoint */
- .long _ex_trap_c /* 0x02 - User Defined */
+ .long _ex_replaceable /* 0x02 - User Defined */
.long _ex_trap_c /* 0x03 - User Defined - userspace stack overflow */
- .long _ex_trap_c /* 0x04 - User Defined */
- .long _ex_trap_c /* 0x05 - User Defined */
- .long _ex_trap_c /* 0x06 - User Defined */
- .long _ex_trap_c /* 0x07 - User Defined */
- .long _ex_trap_c /* 0x08 - User Defined */
- .long _ex_trap_c /* 0x09 - User Defined */
- .long _ex_trap_c /* 0x0A - User Defined */
- .long _ex_trap_c /* 0x0B - User Defined */
- .long _ex_trap_c /* 0x0C - User Defined */
- .long _ex_trap_c /* 0x0D - User Defined */
- .long _ex_trap_c /* 0x0E - User Defined */
- .long _ex_trap_c /* 0x0F - User Defined */
+ .long _ex_replaceable /* 0x04 - User Defined */
+ .long _ex_replaceable /* 0x05 - User Defined */
+ .long _ex_replaceable /* 0x06 - User Defined */
+ .long _ex_replaceable /* 0x07 - User Defined */
+ .long _ex_replaceable /* 0x08 - User Defined */
+ .long _ex_replaceable /* 0x09 - User Defined */
+ .long _ex_replaceable /* 0x0A - User Defined */
+ .long _ex_replaceable /* 0x0B - User Defined */
+ .long _ex_replaceable /* 0x0C - User Defined */
+ .long _ex_replaceable /* 0x0D - User Defined */
+ .long _ex_replaceable /* 0x0E - User Defined */
+ .long _ex_replaceable /* 0x0F - User Defined */
.long _ex_single_step /* 0x10 - HW Single step */
+#ifdef CONFIG_DEBUG_BFIN_HWTRACE_EXPAND
+ .long _ex_trace_buff_full /* 0x11 - Trace Buffer Full */
+#else
.long _ex_trap_c /* 0x11 - Trace Buffer Full */
+#endif
.long _ex_trap_c /* 0x12 - Reserved */
.long _ex_trap_c /* 0x13 - Reserved */
.long _ex_trap_c /* 0x14 - Reserved */
.long _ex_trap_c /* 0x3D - Reserved */
.long _ex_trap_c /* 0x3E - Reserved */
.long _ex_trap_c /* 0x3F - Reserved */
+END(_ex_table)
-ALIGN
ENTRY(_sys_call_table)
.long _sys_restart_syscall /* 0 */
.long _sys_exit
.endr
_exception_stack_top:
-#if defined(ANOMALY_05000261)
+#if ANOMALY_05000261
/* Used by the assembly entry point to work around an anomaly. */
_last_cplb_fault_retx:
.long 0;
.align 4 /* just in case */
-/*
- * initial interrupt handlers
- */
-
-#ifndef CONFIG_KGDB
- /* interrupt routine for emulation - 0 */
- /* Currently used only if GDB stub is not in - invalid */
- /* gdb-stub set the evt itself */
- /* save registers for post-mortem only */
-ENTRY(_evt_emulation)
- SAVE_ALL_SYS
-#ifdef CONFIG_FRAME_POINTER
- fp = 0;
-#endif
- r0 = IRQ_EMU;
- r1 = sp;
- SP += -12;
- call _irq_panic;
- SP += 12;
- /* - GDB stub fills this in by itself (if defined) */
- rte;
-ENDPROC(_evt_emulation)
-#endif
-
/* Common interrupt entry code. First we do CLI, then push
* RETI, to keep interrupts disabled, but to allow this state to be changed
* by local_bh_enable.
fp = 0;
#endif
-#if defined (ANOMALY_05000283) || defined (ANOMALY_05000315)
+#if ANOMALY_05000283 || ANOMALY_05000315
cc = r7 == r7;
p5.h = 0xffc0;
p5.l = 0x0014;
#ifdef CONFIG_FRAME_POINTER
fp = 0;
#endif
-#ifdef ANOMALY_05000283
+#if ANOMALY_05000283
cc = r7 == r7;
p5.h = 0xffc0;
p5.l = 0x0014;
jump .Lcommon_restore_context;
#endif
-/* interrupt routine for evt2 - 2. This is NMI. */
-ENTRY(_evt_evt2)
- SAVE_CONTEXT
-#ifdef CONFIG_FRAME_POINTER
- fp = 0;
-#endif
-#ifdef ANOMALY_05000283
- cc = r7 == r7;
- p5.h = 0xffc0;
- p5.l = 0x0014;
- if cc jump 1f;
- r7.l = W[p5];
-1:
-#endif
- r0 = IRQ_NMI;
- r1 = sp;
- SP += -12;
- call _asm_do_IRQ;
- SP += 12;
- RESTORE_CONTEXT
+/* Interrupt routine for evt2 (NMI).
+ * We don't actually use this, so just return.
+ * For inner circle type details, please see:
+ * http://docs.blackfin.uclinux.org/doku.php?id=linux:nmi
+ */
+ENTRY(_evt_nmi)
+.weak _evt_nmi
rtn;
+ENDPROC(_evt_nmi)
/* interrupt routine for core timer - 6 */
ENTRY(_evt_timer)
if (!(gpio_enabled[gpio_bank(gpionr)] & gpio_bit(gpionr))) {
- ret = gpio_request(gpionr, NULL);
+ ret = gpio_request(gpionr, "IRQ");
if (ret)
return ret;
if (!(gpio_enabled[gpio_bank(gpionr)] & gpio_bit(gpionr))) {
- ret = gpio_request(gpionr, NULL);
+ ret = gpio_request(gpionr, "IRQ");
if (ret)
return ret;
{
SSYNC();
-#ifndef CONFIG_KGDB
- bfin_write_EVT0(evt_emulation);
-#endif
- bfin_write_EVT2(evt_evt2);
+ /* cannot program in software:
+ * evt0 - emulation (jtag)
+ * evt1 - reset
+ */
+ bfin_write_EVT2(evt_nmi);
bfin_write_EVT3(trap);
bfin_write_EVT5(evt_ivhw);
bfin_write_EVT6(evt_timer);
u16 gpionr = irq - IRQ_PF0;
if (!(gpio_enabled[gpio_bank(gpionr)] & gpio_bit(gpionr))) {
- ret = gpio_request(gpionr, NULL);
+ ret = gpio_request(gpionr, "IRQ");
if (ret)
return ret;
}
if (type & (IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING |
IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_LEVEL_LOW)) {
if (!(gpio_enabled[gpio_bank(gpionr)] & gpio_bit(gpionr))) {
- ret = gpio_request(gpionr, NULL);
+ ret = gpio_request(gpionr, "IRQ");
if (ret)
return ret;
}
}
if (!(gpio_enabled[gpio_bank(gpionr)] & gpio_bit(gpionr))) {
- ret = gpio_request(gpionr, NULL);
+ ret = gpio_request(gpionr, "IRQ");
if (ret)
return ret;
}
if (type & (IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING |
IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_LEVEL_LOW)) {
if (!(gpio_enabled[gpio_bank(gpionr)] & gpio_bit(gpionr))) {
- ret = gpio_request(gpionr, NULL);
+ ret = gpio_request(gpionr, "IRQ");
if (ret)
return ret;
}
{
SSYNC();
-#ifndef CONFIG_KGDB
- bfin_write_EVT0(evt_emulation);
-#endif
- bfin_write_EVT2(evt_evt2);
+ /* cannot program in software:
+ * evt0 - emulation (jtag)
+ * evt1 - reset
+ */
+ bfin_write_EVT2(evt_nmi);
bfin_write_EVT3(trap);
bfin_write_EVT5(evt_ivhw);
bfin_write_EVT6(evt_timer);
.text
-#ifdef CONFIG_BLKFIN_CACHE_LOCK
+#ifdef CONFIG_BFIN_ICACHE_LOCK
/* When you come here, it is assumed that
* R0 - Which way to be locked
[--SP]=( R7:0,P5:0 );
- P1.H = (IMEM_CONTROL >> 16);
- P1.L = (IMEM_CONTROL & 0xFFFF);
- P5.H = (ICPLB_ADDR0 >> 16);
- P5.L = (ICPLB_ADDR0 & 0xFFFF);
- P4.H = (ICPLB_DATA0 >> 16);
- P4.L = (ICPLB_DATA0 & 0xFFFF);
+ P1.H = HI(IMEM_CONTROL);
+ P1.L = LO(IMEM_CONTROL);
+ P5.H = HI(ICPLB_ADDR0);
+ P5.L = LO(ICPLB_ADDR0);
+ P4.H = HI(ICPLB_DATA0);
+ P4.L = LO(ICPLB_DATA0);
R7 = R0;
/* If the code of interest already resides in the cache
[--SP]=( R7:0,P5:0 );
- P1.H = (IMEM_CONTROL >> 16);
- P1.L = (IMEM_CONTROL & 0xFFFF);
+ P1.H = HI(IMEM_CONTROL);
+ P1.L = LO(IMEM_CONTROL);
/* Disable the Interrupts*/
CLI R3;
RTS;
ENDPROC(_cache_lock)
-#endif /* BLKFIN_CACHE_LOCK */
+#endif /* BFIN_ICACHE_LOCK */
/* Return the ILOC bits of IMEM_CONTROL
*/
ENTRY(_read_iloc)
- P1.H = (IMEM_CONTROL >> 16);
- P1.L = (IMEM_CONTROL & 0xFFFF);
+ P1.H = HI(IMEM_CONTROL);
+ P1.L = LO(IMEM_CONTROL);
R1 = 0xF;
R0 = [P1];
R0 = R0 >> 3;
unsigned long empty_zero_page;
-void __init show_mem(void)
+void show_mem(void)
{
unsigned long i;
int free = 0, total = 0, reserved = 0, shared = 0;
unsigned int tmp;
tmp = bfin_read_PFCTL();
- __builtin_bfin_csync();
+ CSYNC();
return tmp;
}
static inline void ctr_write(unsigned int val)
{
bfin_write_PFCTL(val);
- __builtin_bfin_csync();
+ CSYNC();
}
static inline void count_read(unsigned int *count)
{
count[0] = bfin_read_PFCNTR0();
count[1] = bfin_read_PFCNTR1();
- __builtin_bfin_csync();
+ CSYNC();
}
static inline void count_write(unsigned int *count)
{
bfin_write_PFCNTR0(count[0]);
bfin_write_PFCNTR1(count[1]);
- __builtin_bfin_csync();
+ CSYNC();
}
extern int pm_overflow_handler(int irq, struct pt_regs *regs);
{
struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
-#ifdef CONFIG_BF54x
while (!(UART_GET_LSR(uart) & TEMT))
continue;
-#endif
#ifdef CONFIG_SERIAL_BFIN_DMA
disable_dma(uart->tx_dma_channel);
ier = UART_GET_IER(uart);
ier |= ETBEI;
UART_PUT_IER(uart, ier);
- bfin_serial_tx_chars(uart);
#endif
+ bfin_serial_tx_chars(uart);
#endif
}
static void bfin_serial_stop_rx(struct uart_port *port)
{
struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+#ifdef CONFIG_KGDB_UART
+ if (uart->port.line != CONFIG_KGDB_UART_PORT) {
+#endif
#ifdef CONFIG_BF54x
UART_CLEAR_IER(uart, ERBFI);
#else
unsigned short ier;
ier = UART_GET_IER(uart);
-#ifdef CONFIG_KGDB_UART
- if (uart->port.line != CONFIG_KGDB_UART_PORT)
-#endif
ier &= ~ERBFI;
UART_PUT_IER(uart, ier);
#endif
+#ifdef CONFIG_KGDB_UART
+ }
+#endif
}
/*
uart = &bfin_serial_ports[CONFIG_KGDB_UART_PORT];
while (!(UART_GET_LSR(uart) & THRE)) {
- __builtin_bfin_ssync();
+ SSYNC();
}
+
+#ifndef CONFIG_BF54x
UART_PUT_LCR(uart, UART_GET_LCR(uart)&(~DLAB));
- __builtin_bfin_ssync();
+ SSYNC();
+#endif
UART_PUT_CHAR(uart, (unsigned char)chr);
- __builtin_bfin_ssync();
+ SSYNC();
}
int kgdb_get_debug_char(void)
uart = &bfin_serial_ports[CONFIG_KGDB_UART_PORT];
while(!(UART_GET_LSR(uart) & DR)) {
- __builtin_bfin_ssync();
+ SSYNC();
}
+#ifndef CONFIG_BF54x
UART_PUT_LCR(uart, UART_GET_LCR(uart)&(~DLAB));
- __builtin_bfin_ssync();
+ SSYNC();
+#endif
chr = UART_GET_CHAR(uart);
- __builtin_bfin_ssync();
+ SSYNC();
return chr;
}
{
struct tty_struct *tty = uart->port.info->tty;
unsigned int status, ch, flg;
+ static int in_break = 0;
#ifdef CONFIG_KGDB_UART
struct pt_regs *regs = get_irq_regs();
#endif
-#ifdef BF533_FAMILY
- static int in_break = 0;
-#endif
status = UART_GET_LSR(uart);
ch = UART_GET_CHAR(uart);
}
}
#endif
-
-#ifdef BF533_FAMILY
- /* The BF533 family of processors have a nice misbehavior where
- * they continuously generate characters for a "single" break.
- * We have to basically ignore this flood until the "next" valid
- * character comes across. All other Blackfin families operate
- * properly though.
- */
- if (in_break) {
- if (ch != 0) {
- in_break = 0;
- ch = UART_GET_CHAR(uart);
- if (bfin_revid() < 5)
+
+ if (ANOMALY_05000230) {
+ /* The BF533 family of processors have a nice misbehavior where
+ * they continuously generate characters for a "single" break.
+ * We have to basically ignore this flood until the "next" valid
+ * character comes across. All other Blackfin families operate
+ * properly though.
+ * Note: While Anomaly 05000230 does not directly address this,
+ * the changes that went in for it also fixed this issue.
+ */
+ if (in_break) {
+ if (ch != 0) {
+ in_break = 0;
+ ch = UART_GET_CHAR(uart);
+ if (bfin_revid() < 5)
+ return;
+ } else
return;
- } else
- return;
+ }
}
-#endif
if (status & BI) {
-#ifdef BF533_FAMILY
- in_break = 1;
-#endif
+ if (ANOMALY_05000230)
+ in_break = 1;
uart->port.icount.brk++;
if (uart_handle_break(&uart->port))
goto ignore_char;
uart->rx_dma_timer.expires = jiffies + DMA_RX_FLUSH_JIFFIES;
add_timer(&(uart->rx_dma_timer));
#else
+ if (request_irq(uart->port.irq, bfin_serial_rx_int, IRQF_DISABLED,
+ "BFIN_UART_RX", uart)) {
# ifdef CONFIG_KGDB_UART
- if (uart->port.line != CONFIG_KGDB_UART_PORT && request_irq
-# else
- if (request_irq
+ if (uart->port.line != CONFIG_KGDB_UART_PORT) {
# endif
- (uart->port.irq, bfin_serial_rx_int, IRQF_DISABLED,
- "BFIN_UART_RX", uart)) {
printk(KERN_NOTICE "Unable to attach BlackFin UART RX interrupt\n");
return -EBUSY;
+# ifdef CONFIG_KGDB_UART
+ }
+# endif
}
+
if (request_irq
(uart->port.irq+1, bfin_serial_tx_int, IRQF_DISABLED,
"BFIN_UART_TX", uart)) {
}
#ifdef CONFIG_SERIAL_BFIN_CONSOLE
-static void bfin_serial_console_putchar(struct uart_port *port, int ch)
-{
- struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
- while (!(UART_GET_LSR(uart) & THRE))
- barrier();
- UART_PUT_CHAR(uart, ch);
- SSYNC();
-}
-
-/*
- * Interrupts are disabled on entering
- */
-static void
-bfin_serial_console_write(struct console *co, const char *s, unsigned int count)
-{
- struct bfin_serial_port *uart = &bfin_serial_ports[co->index];
- int flags = 0;
-
- spin_lock_irqsave(&uart->port.lock, flags);
- uart_console_write(&uart->port, s, count, bfin_serial_console_putchar);
- spin_unlock_irqrestore(&uart->port.lock, flags);
-
-}
-
/*
* If the port was already initialised (eg, by a boot loader),
* try to determine the current setup.
}
pr_debug("%s:baud = %d, parity = %c, bits= %d\n", __FUNCTION__, *baud, *parity, *bits);
}
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN_CONSOLE) || defined(CONFIG_EARLY_PRINTK)
+static struct uart_driver bfin_serial_reg;
static int __init
bfin_serial_console_setup(struct console *co, char *options)
{
struct bfin_serial_port *uart;
+# ifdef CONFIG_SERIAL_BFIN_CONSOLE
int baud = 57600;
int bits = 8;
int parity = 'n';
-#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+# ifdef CONFIG_SERIAL_BFIN_CTSRTS
int flow = 'r';
-#else
+# else
int flow = 'n';
-#endif
+# endif
+# endif
/*
* Check whether an invalid uart number has been specified, and
co->index = 0;
uart = &bfin_serial_ports[co->index];
+# ifdef CONFIG_SERIAL_BFIN_CONSOLE
if (options)
uart_parse_options(options, &baud, &parity, &bits, &flow);
else
bfin_serial_console_get_options(uart, &baud, &parity, &bits);
return uart_set_options(&uart->port, co, baud, parity, bits, flow);
+# else
+ return 0;
+# endif
+}
+#endif /* defined (CONFIG_SERIAL_BFIN_CONSOLE) ||
+ defined (CONFIG_EARLY_PRINTK) */
+
+#ifdef CONFIG_SERIAL_BFIN_CONSOLE
+static void bfin_serial_console_putchar(struct uart_port *port, int ch)
+{
+ struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+ while (!(UART_GET_LSR(uart) & THRE))
+ barrier();
+ UART_PUT_CHAR(uart, ch);
+ SSYNC();
+}
+
+/*
+ * Interrupts are disabled on entering
+ */
+static void
+bfin_serial_console_write(struct console *co, const char *s, unsigned int count)
+{
+ struct bfin_serial_port *uart = &bfin_serial_ports[co->index];
+ int flags = 0;
+
+ spin_lock_irqsave(&uart->port.lock, flags);
+ uart_console_write(&uart->port, s, count, bfin_serial_console_putchar);
+ spin_unlock_irqrestore(&uart->port.lock, flags);
+
}
-static struct uart_driver bfin_serial_reg;
static struct console bfin_serial_console = {
.name = BFIN_SERIAL_NAME,
.write = bfin_serial_console_write,
#define BFIN_SERIAL_CONSOLE &bfin_serial_console
#else
#define BFIN_SERIAL_CONSOLE NULL
-#endif
+#endif /* CONFIG_SERIAL_BFIN_CONSOLE */
+
+
+#ifdef CONFIG_EARLY_PRINTK
+static __init void early_serial_putc(struct uart_port *port, int ch)
+{
+ unsigned timeout = 0xffff;
+ struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+
+ while ((!(UART_GET_LSR(uart) & THRE)) && --timeout)
+ cpu_relax();
+ UART_PUT_CHAR(uart, ch);
+}
+
+static __init void early_serial_write(struct console *con, const char *s,
+ unsigned int n)
+{
+ struct bfin_serial_port *uart = &bfin_serial_ports[con->index];
+ unsigned int i;
+
+ for (i = 0; i < n; i++, s++) {
+ if (*s == '\n')
+ early_serial_putc(&uart->port, '\r');
+ early_serial_putc(&uart->port, *s);
+ }
+}
+
+static struct __init console bfin_early_serial_console = {
+ .name = "early_BFuart",
+ .write = early_serial_write,
+ .device = uart_console_device,
+ .flags = CON_PRINTBUFFER,
+ .setup = bfin_serial_console_setup,
+ .index = -1,
+ .data = &bfin_serial_reg,
+};
+
+struct console __init *bfin_earlyserial_init(unsigned int port,
+ unsigned int cflag)
+{
+ struct bfin_serial_port *uart;
+ struct ktermios t;
+
+ if (port == -1 || port >= nr_ports)
+ port = 0;
+ bfin_serial_init_ports();
+ bfin_early_serial_console.index = port;
+ uart = &bfin_serial_ports[port];
+ t.c_cflag = cflag;
+ t.c_iflag = 0;
+ t.c_oflag = 0;
+ t.c_lflag = ICANON;
+ t.c_line = port;
+ bfin_serial_set_termios(&uart->port, &t, &t);
+ return &bfin_early_serial_console;
+}
+
+#endif /* CONFIG_SERIAL_BFIN_CONSOLE */
static struct uart_driver bfin_serial_reg = {
.owner = THIS_MODULE,
int ret;
#ifdef CONFIG_KGDB_UART
struct bfin_serial_port *uart = &bfin_serial_ports[CONFIG_KGDB_UART_PORT];
- struct termios t;
+ struct ktermios t;
#endif
pr_info("Serial: Blackfin serial driver\n");
}
#ifdef CONFIG_KGDB_UART
if (uart->port.cons->index != CONFIG_KGDB_UART_PORT) {
- request_irq(uart->port.irq, bfin_serial_int,
+ request_irq(uart->port.irq, bfin_serial_rx_int,
IRQF_DISABLED, "BFIN_UART_RX", uart);
pr_info("Request irq for kgdb uart port\n");
+#ifdef CONFIG_BF54x
+ UART_SET_IER(uart, ERBFI);
+#else
UART_PUT_IER(uart, UART_GET_IER(uart) | ERBFI);
- __builtin_bfin_ssync();
+#endif
+ SSYNC();
t.c_cflag = CS8|B57600;
t.c_iflag = 0;
t.c_oflag = 0;
#ifndef _SPI_CHANNEL_H_
#define _SPI_CHANNEL_H_
-#define SPI0_REGBASE 0xffc00500
-
#define SPI_READ 0
#define SPI_WRITE 1
#define HI(con32) (((con32) >> 16) & 0xFFFF)
#define hi(con32) (((con32) >> 16) & 0xFFFF)
-#include <asm/mach/blackfin.h>
-#include <asm/bfin-global.h>
+#include <asm/mach/anomaly.h>
#ifndef __ASSEMBLY__
/* SSYNC implementation for C file */
-#if defined(ANOMALY_05000312) && defined(ANOMALY_05000244)
-static inline void SSYNC (void)
-{
- int _tmp;
- __asm__ __volatile__ ("cli %0;\n\t"
- "nop;nop;\n\t"
- "ssync;\n\t"
- "sti %0;\n\t"
- :"=d"(_tmp):);
-}
-#elif defined(ANOMALY_05000312) && !defined(ANOMALY_05000244)
-static inline void SSYNC (void)
+static inline void SSYNC(void)
{
int _tmp;
- __asm__ __volatile__ ("cli %0;\n\t"
- "ssync;\n\t"
- "sti %0;\n\t"
- :"=d"(_tmp):);
+ if (ANOMALY_05000312)
+ __asm__ __volatile__(
+ "cli %0;"
+ "nop;"
+ "nop;"
+ "ssync;"
+ "sti %0;"
+ : "=d" (_tmp)
+ );
+ else if (ANOMALY_05000244)
+ __asm__ __volatile__(
+ "nop;"
+ "nop;"
+ "nop;"
+ "ssync;"
+ );
+ else
+ __asm__ __volatile__("ssync;");
}
-#elif !defined(ANOMALY_05000312) && defined(ANOMALY_05000244)
-static inline void SSYNC (void)
-{
- __asm__ __volatile__ ("nop; nop; nop;\n\t"
- "ssync;\n\t"
- ::);
-}
-#elif !defined(ANOMALY_05000312) && !defined(ANOMALY_05000244)
-static inline void SSYNC (void)
-{
- __asm__ __volatile__ ("ssync;\n\t");
-}
-#endif
/* CSYNC implementation for C file */
-#if defined(ANOMALY_05000312) && defined(ANOMALY_05000244)
-static inline void CSYNC (void)
-{
- int _tmp;
- __asm__ __volatile__ ("cli %0;\n\t"
- "nop;nop;\n\t"
- "csync;\n\t"
- "sti %0;\n\t"
- :"=d"(_tmp):);
-}
-#elif defined(ANOMALY_05000312) && !defined(ANOMALY_05000244)
-static inline void CSYNC (void)
+static inline void CSYNC(void)
{
int _tmp;
- __asm__ __volatile__ ("cli %0;\n\t"
- "csync;\n\t"
- "sti %0;\n\t"
- :"=d"(_tmp):);
-}
-#elif !defined(ANOMALY_05000312) && defined(ANOMALY_05000244)
-static inline void CSYNC (void)
-{
- __asm__ __volatile__ ("nop; nop; nop;\n\t"
- "ssync;\n\t"
- ::);
+ if (ANOMALY_05000312)
+ __asm__ __volatile__(
+ "cli %0;"
+ "nop;"
+ "nop;"
+ "csync;"
+ "sti %0;"
+ : "=d" (_tmp)
+ );
+ else if (ANOMALY_05000244)
+ __asm__ __volatile__(
+ "nop;"
+ "nop;"
+ "nop;"
+ "csync;"
+ );
+ else
+ __asm__ __volatile__("csync;");
}
-#elif !defined(ANOMALY_05000312) && !defined(ANOMALY_05000244)
-static inline void CSYNC (void)
-{
- __asm__ __volatile__ ("csync;\n\t");
-}
-#endif
#else /* __ASSEMBLY__ */
#define ssync(x) SSYNC(x)
#define csync(x) CSYNC(x)
-#if defined(ANOMALY_05000312) && defined(ANOMALY_05000244)
+#if ANOMALY_05000312
#define SSYNC(scratch) cli scratch; nop; nop; SSYNC; sti scratch;
#define CSYNC(scratch) cli scratch; nop; nop; CSYNC; sti scratch;
-#elif defined(ANOMALY_05000312) && !defined(ANOMALY_05000244)
-#define SSYNC(scratch) cli scratch; nop; nop; SSYNC; sti scratch;
-#define CSYNC(scratch) cli scratch; nop; nop; CSYNC; sti scratch;
-
-#elif !defined(ANOMALY_05000312) && defined(ANOMALY_05000244)
+#elif ANOMALY_05000244
#define SSYNC(scratch) nop; nop; nop; SSYNC;
#define CSYNC(scratch) nop; nop; nop; CSYNC;
-#elif !defined(ANOMALY_05000312) && !defined(ANOMALY_05000244)
+#else
#define SSYNC(scratch) SSYNC;
#define CSYNC(scratch) CSYNC;
#endif /* __ASSEMBLY__ */
+#include <asm/mach/blackfin.h>
+#include <asm/bfin-global.h>
+
#endif /* _BLACKFIN_H_ */
static inline void flush_icache_range(unsigned start, unsigned end)
{
-#if defined(CONFIG_BLKFIN_DCACHE) && defined(CONFIG_BLKFIN_CACHE)
+#if defined(CONFIG_BFIN_DCACHE) && defined(CONFIG_BFIN_ICACHE)
-# if defined(CONFIG_BLKFIN_WT)
+# if defined(CONFIG_BFIN_WT)
blackfin_icache_flush_range((start), (end));
# else
blackfin_icache_dcache_flush_range((start), (end));
#else
-# if defined(CONFIG_BLKFIN_CACHE)
+# if defined(CONFIG_BFIN_ICACHE)
blackfin_icache_flush_range((start), (end));
# endif
-# if defined(CONFIG_BLKFIN_DCACHE)
+# if defined(CONFIG_BFIN_DCACHE)
blackfin_dcache_flush_range((start), (end));
# endif
} while (0)
#define copy_from_user_page(vma, page, vaddr, dst, src, len) memcpy(dst, src, len)
-#if defined(CONFIG_BLKFIN_DCACHE)
+#if defined(CONFIG_BFIN_DCACHE)
# define invalidate_dcache_range(start,end) blackfin_dcache_invalidate_range((start), (end))
#else
# define invalidate_dcache_range(start,end) do { } while (0)
#endif
-#if defined(CONFIG_BLKFIN_DCACHE) && defined(CONFIG_BLKFIN_WB)
+#if defined(CONFIG_BFIN_DCACHE) && defined(CONFIG_BFIN_WB)
# define flush_dcache_range(start,end) blackfin_dcache_flush_range((start), (end))
# define flush_dcache_page(page) blackfin_dflush_page(page_address(page))
#else
# define flush_dcache_page(page) do { } while (0)
#endif
-#endif /* _BLACKFIN_CACHEFLUSH_H */
+#endif /* _BLACKFIN_ICACHEFLUSH_H */
-/************************************************************************
+/*
+ * File: include/asm-blackfin/cplb.h
+ * Based on: include/asm-blackfin/mach-bf537/bf537.h
+ * Author: Robin Getz <rgetz@blackfin.uclinux.org>
*
- * cplb.h
+ * Created: 2000
+ * Description: Common CPLB definitions for CPLB init
*
- * (c) Copyright 2002-2003 Analog Devices, Inc. All rights reserved.
+ * Modified:
+ * Copyright 2004-2007 Analog Devices Inc.
*
- ************************************************************************/
-
-/* Defines necessary for cplb initialisation routines. */
+ * Bugs: Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see the file COPYING, or write
+ * to the Free Software Foundation, Inc.,
+ * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
#ifndef _CPLB_H
#define _CPLB_H
-# include <asm/blackfin.h>
+#include <asm/blackfin.h>
+#include <asm/mach/anomaly.h>
+
+#define SDRAM_IGENERIC (CPLB_L1_CHBL | CPLB_USER_RD | CPLB_VALID | CPLB_PORTPRIO)
+#define SDRAM_IKERNEL (SDRAM_IGENERIC | CPLB_LOCK)
+#define L1_IMEMORY ( CPLB_USER_RD | CPLB_VALID | CPLB_LOCK)
+#define SDRAM_INON_CHBL ( CPLB_USER_RD | CPLB_VALID)
+
+/*Use the menuconfig cache policy here - CONFIG_BFIN_WT/CONFIG_BFIN_WB*/
+
+#if ANOMALY_05000158
+#define ANOMALY_05000158_WORKAROUND 0x200
+#else
+#define ANOMALY_05000158_WORKAROUND 0x0
+#endif
+
+#define CPLB_COMMON (CPLB_DIRTY | CPLB_SUPV_WR | CPLB_USER_WR | CPLB_USER_RD | CPLB_VALID | ANOMALY_05000158_WORKAROUND)
+
+#ifdef CONFIG_BFIN_WB /*Write Back Policy */
+#define SDRAM_DGENERIC (CPLB_L1_CHBL | CPLB_COMMON)
+#else /*Write Through */
+#define SDRAM_DGENERIC (CPLB_L1_CHBL | CPLB_WT | CPLB_L1_AOW | CPLB_COMMON)
+#endif
+
+#define L1_DMEMORY (CPLB_LOCK | CPLB_COMMON)
+#define L2_MEMORY (CPLB_COMMON)
+#define SDRAM_DNON_CHBL (CPLB_COMMON)
+#define SDRAM_EBIU (CPLB_COMMON)
+#define SDRAM_OOPS (CPLB_VALID | ANOMALY_05000158_WORKAROUND | CPLB_LOCK | CPLB_DIRTY)
+
+#define SIZE_1K 0x00000400 /* 1K */
+#define SIZE_4K 0x00001000 /* 4K */
+#define SIZE_1M 0x00100000 /* 1M */
+#define SIZE_4M 0x00400000 /* 4M */
+
+#define MAX_CPLBS (16 * 2)
+
+#define ASYNC_MEMORY_CPLB_COVERAGE ((ASYNC_BANK0_SIZE + ASYNC_BANK1_SIZE + \
+ ASYNC_BANK2_SIZE + ASYNC_BANK3_SIZE) / SIZE_4M)
+
+/*
+* Number of required data CPLB switchtable entries
+* MEMSIZE / 4 (we mostly install 4M page size CPLBs
+* approx 16 for smaller 1MB page size CPLBs for allignment purposes
+* 1 for L1 Data Memory
+* possibly 1 for L2 Data Memory
+* 1 for CONFIG_DEBUG_HUNT_FOR_ZERO
+* 1 for ASYNC Memory
+*/
+
+
+#define MAX_SWITCH_D_CPLBS (((CONFIG_MEM_SIZE / 4) + 16 + 1 + 1 + 1 \
+ + ASYNC_MEMORY_CPLB_COVERAGE) * 2)
+
+/*
+* Number of required instruction CPLB switchtable entries
+* MEMSIZE / 4 (we mostly install 4M page size CPLBs
+* approx 12 for smaller 1MB page size CPLBs for allignment purposes
+* 1 for L1 Instruction Memory
+* possibly 1 for L2 Instruction Memory
+* 1 for CONFIG_DEBUG_HUNT_FOR_ZERO
+*/
+
+#define MAX_SWITCH_I_CPLBS (((CONFIG_MEM_SIZE / 4) + 12 + 1 + 1 + 1) * 2)
+
#define CPLB_ENABLE_ICACHE_P 0
#define CPLB_ENABLE_DCACHE_P 1
#define CPLB_DEF_CACHE CPLB_L1_CHBL | CPLB_WT
#define CPLB_CACHE_ENABLED CPLB_L1_CHBL | CPLB_DIRTY
-#define CPLB_ALL_ACCESS CPLB_SUPV_WR | CPLB_USER_RD | CPLB_USER_WR
-
#define CPLB_I_PAGE_MGMT CPLB_LOCK | CPLB_VALID
#define CPLB_D_PAGE_MGMT CPLB_LOCK | CPLB_ALL_ACCESS | CPLB_VALID
#define CPLB_DNOCACHE CPLB_ALL_ACCESS | CPLB_VALID
/* functions to set register mode */
void set_dma_start_addr(unsigned int channel, unsigned long addr);
void set_dma_next_desc_addr(unsigned int channel, unsigned long addr);
+void set_dma_curr_desc_addr(unsigned int channel, unsigned long addr);
void set_dma_x_count(unsigned int channel, unsigned short x_count);
void set_dma_x_modify(unsigned int channel, short x_modify);
void set_dma_y_count(unsigned int channel, unsigned short y_count);
void set_dma_config(unsigned int channel, unsigned short config);
unsigned short set_bfin_dma_config(char direction, char flow_mode,
char intr_mode, char dma_mode, char width);
+void set_dma_curr_addr(unsigned int channel, unsigned long addr);
/* get curr status for polling */
unsigned short get_dma_curr_irqstat(unsigned int channel);
--- /dev/null
+/*
+ * File: include/asm-blackfin/early_printk.h
+ * Author: Robin Getz <rgetz@blackfin.uclinux.org
+ *
+ * Created: 14Aug2007
+ * Description: function prototpyes for early printk
+ *
+ * Modified:
+ * Copyright 2004-2007 Analog Devices Inc.
+ *
+ * Bugs: Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifdef CONFIG_EARLY_PRINTK
+extern int setup_early_printk(char *);
+#else
+#define setup_early_printk(fmt) do { } while (0)
+#endif /* CONFIG_EARLY_PRINTK */
#ifdef BF533_FAMILY
#define MAX_BLACKFIN_GPIOS 16
+
+#define GPIO_PF0 0
+#define GPIO_PF1 1
+#define GPIO_PF2 2
+#define GPIO_PF3 3
+#define GPIO_PF4 4
+#define GPIO_PF5 5
+#define GPIO_PF6 6
+#define GPIO_PF7 7
+#define GPIO_PF8 8
+#define GPIO_PF9 9
+#define GPIO_PF10 10
+#define GPIO_PF11 11
+#define GPIO_PF12 12
+#define GPIO_PF13 13
+#define GPIO_PF14 14
+#define GPIO_PF15 15
+
#endif
#ifdef BF537_FAMILY
void gpio_direction_input(unsigned short gpio);
void gpio_direction_output(unsigned short gpio);
+#include <asm-generic/gpio.h> /* cansleep wrappers */
+#include <asm/irq.h>
+
+static inline int gpio_to_irq(unsigned gpio)
+{
+ return (gpio + GPIO_IRQ_BASE);
+}
+
+static inline int irq_to_gpio(unsigned irq)
+{
+ return (irq - GPIO_IRQ_BASE);
+}
+
#endif /* __ASSEMBLY__ */
#endif /* __ARCH_BLACKFIN_GPIO_H__ */
#ifndef __ASSEMBLY__
-extern void outsb(void __iomem *port, const void *addr, unsigned short count);
-extern void outsw(void __iomem *port, const void *addr, unsigned short count);
-extern void outsl(void __iomem *port, const void *addr, unsigned short count);
+extern void outsb(unsigned long port, const void *addr, unsigned long count);
+extern void outsw(unsigned long port, const void *addr, unsigned long count);
+extern void outsl(unsigned long port, const void *addr, unsigned long count);
-extern void insb(const void __iomem *port, void *addr, unsigned short count);
-extern void insw(const void __iomem *port, void *addr, unsigned short count);
-extern void insl(const void __iomem *port, void *addr, unsigned short count);
+extern void insb(unsigned long port, void *addr, unsigned long count);
+extern void insw(unsigned long port, void *addr, unsigned long count);
+extern void insl(unsigned long port, void *addr, unsigned long count);
-extern void dma_outsb(void __iomem *port, const void *addr, unsigned short count);
-extern void dma_outsw(void __iomem *port, const void *addr, unsigned short count);
-extern void dma_outsl(void __iomem *port, const void *addr, unsigned short count);
+extern void dma_outsb(unsigned long port, const void *addr, unsigned short count);
+extern void dma_outsw(unsigned long port, const void *addr, unsigned short count);
+extern void dma_outsl(unsigned long port, const void *addr, unsigned short count);
-extern void dma_insb(const void __iomem *port, void *addr, unsigned short count);
-extern void dma_insw(const void __iomem *port, void *addr, unsigned short count);
-extern void dma_insl(const void __iomem *port, void *addr, unsigned short count);
+extern void dma_insb(unsigned long port, void *addr, unsigned short count);
+extern void dma_insw(unsigned long port, void *addr, unsigned short count);
+extern void dma_insl(unsigned long port, void *addr, unsigned short count);
/*
* Map some physical address range into the kernel address space.
#define TIOCSBRK 0x5427 /* BSD compatibility */
#define TIOCCBRK 0x5428 /* BSD compatibility */
#define TIOCGSID 0x5429 /* Return the session ID of FD */
-#define TIOCGPTN _IOR('T',0x30, unsigned int) /* Get Pty Number (of pty-mux device) */
-#define TIOCSPTLCK _IOW('T',0x31, int) /* Lock/unlock Pty */
+#define TCGETS2 _IOR('T', 0x2A, struct termios2)
+#define TCSETS2 _IOW('T', 0x2B, struct termios2)
+#define TCSETSW2 _IOW('T', 0x2C, struct termios2)
+#define TCSETSF2 _IOW('T', 0x2D, struct termios2)
+/* Get Pty Number (of pty-mux device) */
+#define TIOCGPTN _IOR('T', 0x30, unsigned int)
+#define TIOCSPTLCK _IOW('T', 0x31, int) /* Lock/unlock Pty */
#define FIONCLEX 0x5450 /* these numbers need to be adjusted. */
#define FIOCLEX 0x5451
#ifndef _IRQ_HANDLER_H
#define _IRQ_HANDLER_H
+#include <linux/types.h>
+#include <linux/linkage.h>
+
/* BASE LEVEL interrupt handler routines */
-asmlinkage void evt_emulation(void);
asmlinkage void evt_exception(void);
asmlinkage void trap(void);
asmlinkage void evt_ivhw(void);
asmlinkage void evt_timer(void);
-asmlinkage void evt_evt2(void);
+asmlinkage void evt_nmi(void);
asmlinkage void evt_evt7(void);
asmlinkage void evt_evt8(void);
asmlinkage void evt_evt9(void);
asmlinkage void evt_soft_int1(void);
asmlinkage void evt_system_call(void);
asmlinkage void init_exception_buff(void);
+asmlinkage void trap_c(struct pt_regs *fp);
+asmlinkage void ex_replaceable(void);
+asmlinkage void early_trap(void);
+
+extern void *ex_table[];
+extern void return_from_exception(void);
+
+extern int bfin_request_exception(unsigned int exception, void (*handler)(void));
+extern int bfin_free_exception(unsigned int exception, void (*handler)(void));
#endif
#define STATDA1 0x80
extern void kgdb_print(const char *fmt, ...);
+extern void init_kgdb_uart(void);
#endif
--- /dev/null
+/*
+ * File: include/asm-blackfin/mach-bf527/anomaly.h
+ * Bugs: Enter bugs at http://blackfin.uclinux.org/
+ *
+ * Copyright (C) 2004-2007 Analog Devices Inc.
+ * Licensed under the GPL-2 or later.
+ */
+
+/* This file shoule be up to date with:
+ * - Revision A, May 30, 2007; ADSP-BF527 Blackfin Processor Anomaly List
+ */
+
+#ifndef _MACH_ANOMALY_H_
+#define _MACH_ANOMALY_H_
+
+/* Multi-Issue Instruction with dsp32shiftimm in slot1 and P-reg Store in slot2 Not Supported */
+#define ANOMALY_05000074 (1)
+/* DMA_RUN Bit Is Not Valid after a Peripheral Receive Channel DMA Stops */
+#define ANOMALY_05000119 (1)
+/* Rx.H Cannot Be Used to Access 16-bit System MMR Registers */
+#define ANOMALY_05000122 (1)
+/* Spurious Hardware Error from an Access in the Shadow of a Conditional Branch */
+#define ANOMALY_05000245 (1)
+/* Sensitivity To Noise with Slow Input Edge Rates on External SPORT TX and RX Clocks */
+#define ANOMALY_05000265 (1)
+/* Memory-To-Memory DMA Source/Destination Descriptors Must Be in Same Memory Space */
+#define ANOMALY_05000301 (1)
+/* Errors When SSYNC, CSYNC, or Loads to LT, LB and LC Registers Are Interrupted */
+#define ANOMALY_05000312 (1)
+/* Incorrect Access of OTP_STATUS During otp_write() Function */
+#define ANOMALY_05000328 (1)
+/* Disallowed Configuration Prevents Subsequent Allowed Configuration on Host DMA Port */
+#define ANOMALY_05000337 (1)
+/* TWI Does Not Operate Correctly Under Certain Signal Termination Conditions */
+#define ANOMALY_05000342 (1)
+/* Boot ROM Kernel Incorrectly Alters Reset Value of USB Register */
+#define ANOMALY_05000347 (1)
+
+/* Anomalies that don't exist on this proc */
+#define ANOMALY_05000323 (0)
+#endif
/* SPI Controller (0xFFC00500 - 0xFFC005FF) */
+#define SPI0_REGBASE 0xFFC00500
#define SPI_CTL 0xFFC00500 /* SPI Control Register */
#define SPI_FLG 0xFFC00504 /* SPI Flag register */
#define SPI_STAT 0xFFC00508 /* SPI Status register */
/* Two-Wire Interface (0xFFC01400 - 0xFFC014FF) */
+#define TWI0_REGBASE 0xFFC01400
#define TWI_CLKDIV 0xFFC01400 /* Serial Clock Divider Register */
#define TWI_CONTROL 0xFFC01404 /* TWI Control Register */
#define TWI_SLAVE_CTL 0xFFC01408 /* Slave Mode Control Register */
/*
- * File: include/asm-blackfin/mach-bf533/anomaly.h
- * Based on:
- * Author:
+ * File: include/asm-blackfin/mach-bf533/anomaly.h
+ * Bugs: Enter bugs at http://blackfin.uclinux.org/
*
- * Created:
- * Description:
- *
- * Rev:
- *
- * Modified:
- *
- * Bugs: Enter bugs at http://blackfin.uclinux.org/
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2, or (at your option)
- * any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; see the file COPYING.
- * If not, write to the Free Software Foundation,
- * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ * Copyright (C) 2004-2007 Analog Devices Inc.
+ * Licensed under the GPL-2 or later.
*/
/* This file shoule be up to date with:
- * - Revision U, May 17, 2006; ADSP-BF533 Blackfin Processor Anomaly List
- * - Revision Y, May 17, 2006; ADSP-BF532 Blackfin Processor Anomaly List
- * - Revision T, May 17, 2006; ADSP-BF531 Blackfin Processor Anomaly List
+ * - Revision X, March 23, 2007; ADSP-BF533 Blackfin Processor Anomaly List
+ * - Revision AB, March 23, 2007; ADSP-BF532 Blackfin Processor Anomaly List
+ * - Revision W, March 23, 2007; ADSP-BF531 Blackfin Processor Anomaly List
*/
#ifndef _MACH_ANOMALY_H_
#define _MACH_ANOMALY_H_
/* We do not support 0.1 or 0.2 silicon - sorry */
-#if (defined(CONFIG_BF_REV_0_1) || defined(CONFIG_BF_REV_0_2))
-#error Kernel will not work on BF533 Version 0.1 or 0.2
+#if __SILICON_REVISION__ < 3
+# error Kernel will not work on BF533 silicon version 0.0, 0.1, or 0.2
#endif
-/* Issues that are common to 0.5, 0.4, and 0.3 silicon */
-#if (defined(CONFIG_BF_REV_0_5) || defined(CONFIG_BF_REV_0_4) \
- || defined(CONFIG_BF_REV_0_3))
-#define ANOMALY_05000074 /* A multi issue instruction with dsp32shiftimm in
- slot1 and store of a P register in slot 2 is not
- supported */
-#define ANOMALY_05000105 /* Watchpoint Status Register (WPSTAT) bits are set on
- every corresponding match */
-#define ANOMALY_05000119 /* DMA_RUN bit is not valid after a Peripheral Receive
- Channel DMA stops */
-#define ANOMALY_05000122 /* Rx.H can not be used to access 16-bit System MMR
- registers. */
-#define ANOMALY_05000166 /* PPI Data Lengths Between 8 and 16 do not zero out
- upper bits*/
-#define ANOMALY_05000167 /* Turning Serial Ports on With External Frame Syncs */
-#define ANOMALY_05000180 /* PPI_DELAY not functional in PPI modes with 0 frame
- syncs */
-#define ANOMALY_05000208 /* VSTAT status bit in PLL_STAT register is not
- functional */
-#define ANOMALY_05000219 /* NMI event at boot time results in unpredictable
- state */
-#define ANOMALY_05000229 /* SPI Slave Boot Mode modifies registers */
-#define ANOMALY_05000272 /* Certain data cache write through modes fail for
- VDDint <=0.9V */
-#define ANOMALY_05000273 /* Writes to Synchronous SDRAM memory may be lost */
-#define ANOMALY_05000277 /* Writes to a flag data register one SCLK cycle after
- an edge is detected may clear interrupt */
-#define ANOMALY_05000278 /* Disabling Peripherals with DMA running may cause
- DMA system instability */
-#define ANOMALY_05000281 /* False Hardware Error Exception when ISR context is
- not restored */
-#define ANOMALY_05000282 /* Memory DMA corruption with 32-bit data and traffic
- control */
-#define ANOMALY_05000283 /* A system MMR write is stalled indefinitely when
- killed in a particular stage*/
-#define ANOMALY_05000311 /* Erroneous flag pin operations under specific
- sequences */
-#define ANOMALY_05000312 /* Errors when SSYNC, CSYNC, or loads to LT, LB and LC
- registers are interrupted */
-#define ANOMALY_05000313 /* PPI Is Level-Sensitive on First Transfer */
-#define ANOMALY_05000315 /* Killed System MMR Write Completes Erroneously On
- * Next System MMR Access */
-#define ANOMALY_05000319 /* Internal Voltage Regulator Values of 1.05V, 1.10V
- * and 1.15V Not Allowed for LQFP Packages */
-#endif /* Issues that are common to 0.5, 0.4, and 0.3 silicon */
+#if defined(__ADSPBF531__)
+# define ANOMALY_BF531 1
+#else
+# define ANOMALY_BF531 0
+#endif
+#if defined(__ADSPBF532__)
+# define ANOMALY_BF532 1
+#else
+# define ANOMALY_BF532 0
+#endif
+#if defined(__ADSPBF533__)
+# define ANOMALY_BF533 1
+#else
+# define ANOMALY_BF533 0
+#endif
-/* These issues only occur on 0.3 or 0.4 BF533 */
-#if (defined(CONFIG_BF_REV_0_4) || defined(CONFIG_BF_REV_0_3))
-#define ANOMALY_05000099 /* UART Line Status Register (UART_LSR) bits are not
- updated at the same time. */
-#define ANOMALY_05000158 /* Boot fails when data cache enabled: Data from a Data
- Cache Fill can be corrupted after or during
- Instruction DMA if certain core stalls exist */
-#define ANOMALY_05000179 /* PPI_COUNT cannot be programmed to 0 in General
- Purpose TX or RX modes */
-#define ANOMALY_05000198 /* Failing SYSTEM MMR accesses when stalled by
- preceding memory read */
-#define ANOMALY_05000200 /* SPORT TFS and DT are incorrectly driven during
- inactive channels in certain conditions */
-#define ANOMALY_05000202 /* Possible infinite stall with specific dual dag
- situation */
-#define ANOMALY_05000215 /* UART TX Interrupt masked erroneously */
-#define ANOMALY_05000225 /* Incorrect pulse-width of UART start-bit */
-#define ANOMALY_05000227 /* Scratchpad memory bank reads may return incorrect
- data*/
-#define ANOMALY_05000230 /* UART Receiver is less robust against Baudrate
- Differences in certain Conditions */
-#define ANOMALY_05000231 /* UART STB bit incorrectly affects receiver setting */
-#define ANOMALY_05000242 /* DF bit in PLL_CTL register does not respond to
- hardware reset */
-#define ANOMALY_05000244 /* With instruction cache enabled, a CSYNC or SSYNC or
- IDLE around a Change of Control causes
- unpredictable results */
-#define ANOMALY_05000245 /* Spurious Hardware Error from an access in the
- shadow of a conditional branch */
-#define ANOMALY_05000246 /* Data CPLB's should prevent spurious hardware
- errors */
-#define ANOMALY_05000253 /* Maximum external clock speed for Timers */
-#define ANOMALY_05000255 /* Entering Hibernate Mode with RTC Seconds event
- interrupt not functional */
-#define ANOMALY_05000257 /* An interrupt or exception during short Hardware
- loops may cause the instruction fetch unit to
- malfunction */
-#define ANOMALY_05000258 /* Instruction Cache is corrupted when bit 9 and 12 of
- the ICPLB Data registers differ */
-#define ANOMALY_05000260 /* ICPLB_STATUS MMR register may be corrupted */
-#define ANOMALY_05000261 /* DCPLB_FAULT_ADDR MMR register may be corrupted */
-#define ANOMALY_05000262 /* Stores to data cache may be lost */
-#define ANOMALY_05000263 /* Hardware loop corrupted when taking an ICPLB exception */
-#define ANOMALY_05000264 /* A Sync instruction (CSYNC, SSYNC) or an IDLE
- instruction will cause an infinite stall in the
- second to last instruction in a hardware loop */
-#define ANOMALY_05000265 /* Sensitivity to noise with slow input edge rates on
- SPORT external receive and transmit clocks. */
-#define ANOMALY_05000269 /* High I/O activity causes the output voltage of the
- internal voltage regulator (VDDint) to increase. */
-#define ANOMALY_05000270 /* High I/O activity causes the output voltage of the
- internal voltage regulator (VDDint) to decrease */
-#endif /* issues only occur on 0.3 or 0.4 BF533 */
+/* Multi-Issue Instruction with dsp32shiftimm in slot1 and P-reg Store in slot 2 Not Supported */
+#define ANOMALY_05000074 (1)
+/* UART Line Status Register (UART_LSR) Bits Are Not Updated at the Same Time */
+#define ANOMALY_05000099 (__SILICON_REVISION__ < 5)
+/* Watchpoint Status Register (WPSTAT) Bits Are Set on Every Corresponding Match */
+#define ANOMALY_05000105 (1)
+/* DMA_RUN Bit Is Not Valid after a Peripheral Receive Channel DMA Stops */
+#define ANOMALY_05000119 (1)
+/* Rx.H Cannot Be Used to Access 16-bit System MMR Registers */
+#define ANOMALY_05000122 (1)
+/* Instruction DMA Can Cause Data Cache Fills to Fail (Boot Implications) */
+#define ANOMALY_05000158 (__SILICON_REVISION__ < 5)
+/* PPI Data Lengths Between 8 and 16 Do Not Zero Out Upper Bits */
+#define ANOMALY_05000166 (1)
+/* Turning Serial Ports on with External Frame Syncs */
+#define ANOMALY_05000167 (1)
+/* PPI_COUNT Cannot Be Programmed to 0 in General Purpose TX or RX Modes */
+#define ANOMALY_05000179 (__SILICON_REVISION__ < 5)
+/* PPI_DELAY Not Functional in PPI Modes with 0 Frame Syncs */
+#define ANOMALY_05000180 (1)
+/* Timer Pin Limitations for PPI TX Modes with External Frame Syncs */
+#define ANOMALY_05000183 (__SILICON_REVISION__ < 4)
+/* False Protection Exceptions */
+#define ANOMALY_05000189 (__SILICON_REVISION__ < 4)
+/* False I/O Pin Interrupts on Edge-Sensitive Inputs When Polarity Setting Is Changed */
+#define ANOMALY_05000193 (__SILICON_REVISION__ < 4)
+/* Restarting SPORT in Specific Modes May Cause Data Corruption */
+#define ANOMALY_05000194 (__SILICON_REVISION__ < 4)
+/* Failing MMR Accesses When Stalled by Preceding Memory Read */
+#define ANOMALY_05000198 (__SILICON_REVISION__ < 5)
+/* Current DMA Address Shows Wrong Value During Carry Fix */
+#define ANOMALY_05000199 (__SILICON_REVISION__ < 4)
+/* SPORT TFS and DT Are Incorrectly Driven During Inactive Channels in Certain Conditions */
+#define ANOMALY_05000200 (__SILICON_REVISION__ < 5)
+/* Receive Frame Sync Not Ignored During Active Frames in SPORT Multi-Channel Mode */
+#define ANOMALY_05000201 (__SILICON_REVISION__ < 4)
+/* Possible Infinite Stall with Specific Dual-DAG Situation */
+#define ANOMALY_05000202 (__SILICON_REVISION__ < 5)
+/* Specific Sequence That Can Cause DMA Error or DMA Stopping */
+#define ANOMALY_05000203 (__SILICON_REVISION__ < 4)
+/* Incorrect data read with write-through cache and allocate cache lines on reads only mode */
+#define ANOMALY_05000204 (__SILICON_REVISION__ < 4 && ANOMALY_BF533)
+/* Recovery from "Brown-Out" Condition */
+#define ANOMALY_05000207 (__SILICON_REVISION__ < 4)
+/* VSTAT Status Bit in PLL_STAT Register Is Not Functional */
+#define ANOMALY_05000208 (1)
+/* Speed Path in Computational Unit Affects Certain Instructions */
+#define ANOMALY_05000209 (__SILICON_REVISION__ < 4)
+/* UART TX Interrupt Masked Erroneously */
+#define ANOMALY_05000215 (__SILICON_REVISION__ < 5)
+/* NMI Event at Boot Time Results in Unpredictable State */
+#define ANOMALY_05000219 (1)
+/* Incorrect Pulse-Width of UART Start Bit */
+#define ANOMALY_05000225 (__SILICON_REVISION__ < 5)
+/* Scratchpad Memory Bank Reads May Return Incorrect Data */
+#define ANOMALY_05000227 (__SILICON_REVISION__ < 5)
+/* SPI Slave Boot Mode Modifies Registers from Reset Value */
+#define ANOMALY_05000229 (1)
+/* UART Receiver is Less Robust Against Baudrate Differences in Certain Conditions */
+#define ANOMALY_05000230 (__SILICON_REVISION__ < 5)
+/* UART STB Bit Incorrectly Affects Receiver Setting */
+#define ANOMALY_05000231 (__SILICON_REVISION__ < 5)
+/* PPI_FS3 Is Not Driven in 2 or 3 Internal Frame Sync Transmit Modes */
+#define ANOMALY_05000233 (__SILICON_REVISION__ < 4)
+/* Incorrect Revision Number in DSPID Register */
+#define ANOMALY_05000234 (__SILICON_REVISION__ == 4)
+/* DF Bit in PLL_CTL Register Does Not Respond to Hardware Reset */
+#define ANOMALY_05000242 (__SILICON_REVISION__ < 4)
+/* If I-Cache Is On, CSYNC/SSYNC/IDLE Around Change of Control Causes Failures */
+#define ANOMALY_05000244 (__SILICON_REVISION__ < 5)
+/* Spurious Hardware Error from an Access in the Shadow of a Conditional Branch */
+#define ANOMALY_05000245 (1)
+/* Data CPLBs Should Prevent Spurious Hardware Errors */
+#define ANOMALY_05000246 (__SILICON_REVISION__ < 5)
+/* Incorrect Bit Shift of Data Word in Multichannel (TDM) Mode in Certain Conditions */
+#define ANOMALY_05000250 (__SILICON_REVISION__ == 4)
+/* Maximum External Clock Speed for Timers */
+#define ANOMALY_05000253 (__SILICON_REVISION__ < 5)
+/* Incorrect Timer Pulse Width in Single-Shot PWM_OUT Mode with External Clock */
+#define ANOMALY_05000254 (__SILICON_REVISION__ > 4)
+/* Entering Hibernate State with RTC Seconds Interrupt Not Functional */
+#define ANOMALY_05000255 (__SILICON_REVISION__ < 5)
+/* Interrupt/Exception During Short Hardware Loop May Cause Bad Instruction Fetches */
+#define ANOMALY_05000257 (__SILICON_REVISION__ < 5)
+/* Instruction Cache Is Corrupted When Bits 9 and 12 of the ICPLB Data Registers Differ */
+#define ANOMALY_05000258 (__SILICON_REVISION__ < 5)
+/* ICPLB_STATUS MMR Register May Be Corrupted */
+#define ANOMALY_05000260 (__SILICON_REVISION__ < 5)
+/* DCPLB_FAULT_ADDR MMR Register May Be Corrupted */
+#define ANOMALY_05000261 (__SILICON_REVISION__ < 5)
+/* Stores To Data Cache May Be Lost */
+#define ANOMALY_05000262 (__SILICON_REVISION__ < 5)
+/* Hardware Loop Corrupted When Taking an ICPLB Exception */
+#define ANOMALY_05000263 (__SILICON_REVISION__ < 5)
+/* CSYNC/SSYNC/IDLE Causes Infinite Stall in Penultimate Instruction in Hardware Loop */
+#define ANOMALY_05000264 (__SILICON_REVISION__ < 5)
+/* Sensitivity To Noise with Slow Input Edge Rates on External SPORT TX and RX Clocks */
+#define ANOMALY_05000265 (__SILICON_REVISION__ < 5)
+/* High I/O Activity Causes Output Voltage of Internal Voltage Regulator (Vddint) to Increase */
+#define ANOMALY_05000269 (__SILICON_REVISION__ < 5)
+/* High I/O Activity Causes Output Voltage of Internal Voltage Regulator (Vddint) to Decrease */
+#define ANOMALY_05000270 (__SILICON_REVISION__ < 5)
+/* Spontaneous Reset of Internal Voltage Regulator */
+#define ANOMALY_05000271 (__SILICON_REVISION__ < 4)
+/* Certain Data Cache Writethrough Modes Fail for Vddint <= 0.9V */
+#define ANOMALY_05000272 (1)
+/* Writes to Synchronous SDRAM Memory May Be Lost */
+#define ANOMALY_05000273 (1)
+/* Timing Requirements Change for External Frame Sync PPI Modes with Non-Zero PPI_DELAY */
+#define ANOMALY_05000276 (1)
+/* Writes to an I/O Data Register One SCLK Cycle after an Edge Is Detected May Clear Interrupt */
+#define ANOMALY_05000277 (1)
+/* Disabling Peripherals with DMA Running May Cause DMA System Instability */
+#define ANOMALY_05000278 (1)
+/* False Hardware Error Exception When ISR Context Is Not Restored */
+#define ANOMALY_05000281 (1)
+/* Memory DMA Corruption with 32-Bit Data and Traffic Control */
+#define ANOMALY_05000282 (1)
+/* System MMR Write Is Stalled Indefinitely When Killed in a Particular Stage */
+#define ANOMALY_05000283 (1)
+/* SPORTs May Receive Bad Data If FIFOs Fill Up */
+#define ANOMALY_05000288 (1)
+/* Memory-To-Memory DMA Source/Destination Descriptors Must Be in Same Memory Space */
+#define ANOMALY_05000301 (1)
+/* SSYNCs After Writes To DMA MMR Registers May Not Be Handled Correctly */
+#define ANOMALY_05000302 (__SILICON_REVISION__ < 5)
+/* New Feature: Additional Hysteresis on SPORT Input Pins (Not Available On Older Silicon) */
+#define ANOMALY_05000305 (__SILICON_REVISION__ < 5)
+/* New Feature: Additional PPI Frame Sync Sampling Options (Not Available On Older Silicon) */
+#define ANOMALY_05000306 (__SILICON_REVISION__ < 5)
+/* False Hardware Errors Caused by Fetches at the Boundary of Reserved Memory */
+#define ANOMALY_05000310 (1)
+/* Erroneous Flag (GPIO) Pin Operations under Specific Sequences */
+#define ANOMALY_05000311 (1)
+/* Errors When SSYNC, CSYNC, or Loads to LT, LB and LC Registers Are Interrupted */
+#define ANOMALY_05000312 (1)
+/* PPI Is Level-Sensitive on First Transfer */
+#define ANOMALY_05000313 (1)
+/* Killed System MMR Write Completes Erroneously On Next System MMR Access */
+#define ANOMALY_05000315 (1)
+/* Internal Voltage Regulator Values of 1.05V, 1.10V and 1.15V Not Allowed for LQFP Packages */
+#define ANOMALY_05000319 (ANOMALY_BF531 || ANOMALY_BF532)
-/* These issues are only on 0.4 silicon */
-#if (defined(CONFIG_BF_REV_0_4))
-#define ANOMALY_05000234 /* Incorrect Revision Number in DSPID Register */
-#define ANOMALY_05000250 /* Incorrect Bit-Shift of Data Word in Multichannel
- (TDM) */
-#endif /* issues are only on 0.4 silicon */
+/* These anomalies have been "phased" out of analog.com anomaly sheets and are
+ * here to show running on older silicon just isn't feasible.
+ */
-/* These issues are only on 0.3 silicon */
-#if defined(CONFIG_BF_REV_0_3)
-#define ANOMALY_05000183 /* Timer Pin limitations for PPI TX Modes with
- External Frame Syncs */
-#define ANOMALY_05000189 /* False Protection Exceptions caused by Speculative
- Instruction or Data Fetches, or by Fetches at the
- boundary of reserved memory space */
-#define ANOMALY_05000193 /* False Flag Pin Interrupts on Edge Sensitive Inputs
- when polarity setting is changed */
-#define ANOMALY_05000194 /* Sport Restarting in specific modes may cause data
- corruption */
-#define ANOMALY_05000199 /* DMA current address shows wrong value during carry
- fix */
-#define ANOMALY_05000201 /* Receive frame sync not ignored during active
- frames in sport MCM */
-#define ANOMALY_05000203 /* Specific sequence that can cause DMA error or DMA
- stopping */
-#if defined(CONFIG_BF533)
-#define ANOMALY_05000204 /* Incorrect data read with write-through cache and
- allocate cache lines on reads only mode */
-#endif /* CONFIG_BF533 */
-#define ANOMALY_05000207 /* Recovery from "brown-out" condition */
-#define ANOMALY_05000209 /* Speed-Path in computational unit affects certain
- instructions */
-#define ANOMALY_05000233 /* PPI_FS3 is not driven in 2 or 3 internal Frame
- Sync Transmit Mode */
-#define ANOMALY_05000271 /* Spontaneous reset of Internal Voltage Regulator */
-#endif /* only on 0.3 silicon */
+/* Watchpoints (Hardware Breakpoints) are not supported */
+#define ANOMALY_05000067 (__SILICON_REVISION__ < 3)
+/* Reserved bits in SYSCFG register not set at power on */
+#define ANOMALY_05000109 (__SILICON_REVISION__ < 3)
+/* Trace Buffers may record discontinuities into emulation mode and/or exception, NMI, reset handlers */
+#define ANOMALY_05000116 (__SILICON_REVISION__ < 3)
+/* DTEST_COMMAND initiated memory access may be incorrect if data cache or DMA is active */
+#define ANOMALY_05000123 (__SILICON_REVISION__ < 3)
+/* DMA Lock-up at CCLK to SCLK ratios of 4:1, 2:1, or 1:1 */
+#define ANOMALY_05000124 (__SILICON_REVISION__ < 3)
+/* Erroneous exception when enabling cache */
+#define ANOMALY_05000125 (__SILICON_REVISION__ < 3)
+/* SPI clock polarity and phase bits incorrect during booting */
+#define ANOMALY_05000126 (__SILICON_REVISION__ < 3)
+/* DMEM_CONTROL is not set on Reset */
+#define ANOMALY_05000137 (__SILICON_REVISION__ < 3)
+/* SPI boot will not complete if there is a zero fill block in the loader file */
+#define ANOMALY_05000138 (__SILICON_REVISION__ < 3)
+/* Allowing the SPORT RX FIFO to fill will cause an overflow */
+#define ANOMALY_05000140 (__SILICON_REVISION__ < 3)
+/* An Infinite Stall occurs with a particular sequence of consecutive dual dag events */
+#define ANOMALY_05000141 (__SILICON_REVISION__ < 3)
+/* Interrupts may be lost when a programmable input flag is configured to be edge sensitive */
+#define ANOMALY_05000142 (__SILICON_REVISION__ < 3)
+/* A read from external memory may return a wrong value with data cache enabled */
+#define ANOMALY_05000143 (__SILICON_REVISION__ < 3)
+/* DMA and TESTSET conflict when both are accessing external memory */
+#define ANOMALY_05000144 (__SILICON_REVISION__ < 3)
+/* In PWM_OUT mode, you must enable the PPI block to generate a waveform from PPI_CLK */
+#define ANOMALY_05000145 (__SILICON_REVISION__ < 3)
+/* MDMA may lose the first few words of a descriptor chain */
+#define ANOMALY_05000146 (__SILICON_REVISION__ < 3)
+/* The source MDMA descriptor may stop with a DMA Error */
+#define ANOMALY_05000147 (__SILICON_REVISION__ < 3)
+/* When booting from a 16-bit asynchronous memory device, the upper 8-bits of each word must be 0x00 */
+#define ANOMALY_05000148 (__SILICON_REVISION__ < 3)
+/* Frame Delay in SPORT Multichannel Mode */
+#define ANOMALY_05000153 (__SILICON_REVISION__ < 3)
+/* SPORT TFS signal is active in Multi-channel mode outside of valid channels */
+#define ANOMALY_05000154 (__SILICON_REVISION__ < 3)
+/* Timer1 can not be used for PWMOUT mode when a certain PPI mode is in use */
+#define ANOMALY_05000155 (__SILICON_REVISION__ < 3)
+/* A killed 32-bit System MMR write will lead to the next system MMR access thinking it should be 32-bit. */
+#define ANOMALY_05000157 (__SILICON_REVISION__ < 3)
+/* SPORT transmit data is not gated by external frame sync in certain conditions */
+#define ANOMALY_05000163 (__SILICON_REVISION__ < 3)
+/* SDRAM auto-refresh and subsequent Power Ups */
+#define ANOMALY_05000168 (__SILICON_REVISION__ < 3)
+/* DATA CPLB page miss can result in lost write-through cache data writes */
+#define ANOMALY_05000169 (__SILICON_REVISION__ < 3)
+/* DMA vs Core accesses to external memory */
+#define ANOMALY_05000173 (__SILICON_REVISION__ < 3)
+/* Cache Fill Buffer Data lost */
+#define ANOMALY_05000174 (__SILICON_REVISION__ < 3)
+/* Overlapping Sequencer and Memory Stalls */
+#define ANOMALY_05000175 (__SILICON_REVISION__ < 3)
+/* Multiplication of (-1) by (-1) followed by an accumulator saturation */
+#define ANOMALY_05000176 (__SILICON_REVISION__ < 3)
+/* Disabling the PPI resets the PPI configuration registers */
+#define ANOMALY_05000181 (__SILICON_REVISION__ < 3)
+/* PPI TX Mode with 2 External Frame Syncs */
+#define ANOMALY_05000185 (__SILICON_REVISION__ < 3)
+/* PPI does not invert the Driving PPICLK edge in Transmit Modes */
+#define ANOMALY_05000191 (__SILICON_REVISION__ < 3)
+/* In PPI Transmit Modes with External Frame Syncs POLC */
+#define ANOMALY_05000192 (__SILICON_REVISION__ < 3)
+/* Internal Voltage Regulator may not start up */
+#define ANOMALY_05000206 (__SILICON_REVISION__ < 3)
-#if defined(CONFIG_BF_REV_0_2)
-#define ANOMALY_05000067 /* Watchpoints (Hardware Breakpoints) are not
- * supported */
-#define ANOMALY_05000109 /* Reserved bits in SYSCFG register not set at
- * power on */
-#define ANOMALY_05000116 /* Trace Buffers may record discontinuities into
- * emulation mode and/or exception, NMI, reset
- * handlers */
-#define ANOMALY_05000123 /* DTEST_COMMAND initiated memory access may be
- * incorrect if data cache or DMA is active */
-#define ANOMALY_05000124 /* DMA Lock-up at CCLK to SCLK ratios of 4:1, 2:1,
- * or 1:1 */
-#define ANOMALY_05000125 /* Erroneous exception when enabling cache */
-#define ANOMALY_05000126 /* SPI clock polarity and phase bits incorrect
- * during booting */
-#define ANOMALY_05000137 /* DMEM_CONTROL is not set on Reset */
-#define ANOMALY_05000138 /* SPI boot will not complete if there is a zero fill
- * block in the loader file */
-#define ANOMALY_05000140 /* Allowing the SPORT RX FIFO to fill will cause an
- * overflow */
-#define ANOMALY_05000141 /* An Infinite Stall occurs with a particular sequence
- * of consecutive dual dag events */
-#define ANOMALY_05000142 /* Interrupts may be lost when a programmable input
- * flag is configured to be edge sensitive */
-#define ANOMALY_05000143 /* A read from external memory may return a wrong
- * value with data cache enabled */
-#define ANOMALY_05000144 /* DMA and TESTSET conflict when both are accessing
- * external memory */
-#define ANOMALY_05000145 /* In PWM_OUT mode, you must enable the PPI block to
- * generate a waveform from PPI_CLK */
-#define ANOMALY_05000146 /* MDMA may lose the first few words of a descriptor
- * chain */
-#define ANOMALY_05000147 /* The source MDMA descriptor may stop with a DMA
- * Error */
-#define ANOMALY_05000148 /* When booting from a 16-bit asynchronous memory
- * device, the upper 8-bits of each word must be
- * 0x00 */
-#define ANOMALY_05000153 /* Frame Delay in SPORT Multichannel Mode */
-#define ANOMALY_05000154 /* SPORT TFS signal is active in Multi-channel mode
- * outside of valid channels */
-#define ANOMALY_05000155 /* Timer1 can not be used for PWMOUT mode when a
- * certain PPI mode is in use */
-#define ANOMALY_05000157 /* A killed 32-bit System MMR write will lead to
- * the next system MMR access thinking it should be
- * 32-bit. */
-#define ANOMALY_05000163 /* SPORT transmit data is not gated by external frame
- * sync in certain conditions */
-#define ANOMALY_05000168 /* SDRAM auto-refresh and subsequent Power Ups */
-#define ANOMALY_05000169 /* DATA CPLB page miss can result in lost
- * write-through cache data writes */
-#define ANOMALY_05000173 /* DMA vs Core accesses to external memory */
-#define ANOMALY_05000174 /* Cache Fill Buffer Data lost */
-#define ANOMALY_05000175 /* Overlapping Sequencer and Memory Stalls */
-#define ANOMALY_05000176 /* Multiplication of (-1) by (-1) followed by an
- * accumulator saturation */
-#define ANOMALY_05000181 /* Disabling the PPI resets the PPI configuration
- * registers */
-#define ANOMALY_05000185 /* PPI TX Mode with 2 External Frame Syncs */
-#define ANOMALY_05000191 /* PPI does not invert the Driving PPICLK edge in
- * Transmit Modes */
-#define ANOMALY_05000192 /* In PPI Transmit Modes with External Frame Syncs
- * POLC */
-#define ANOMALY_05000206 /* Internal Voltage Regulator may not start up */
+/* Anomalies that don't exist on this proc */
+#define ANOMALY_05000266 (0)
+#define ANOMALY_05000323 (0)
#endif
-
-#endif /* _MACH_ANOMALY_H_ */
/***************************/
-#define BLKFIN_DSUBBANKS 4
-#define BLKFIN_DWAYS 2
-#define BLKFIN_DLINES 64
-#define BLKFIN_ISUBBANKS 4
-#define BLKFIN_IWAYS 4
-#define BLKFIN_ILINES 32
+#define BFIN_DSUBBANKS 4
+#define BFIN_DWAYS 2
+#define BFIN_DLINES 64
+#define BFIN_ISUBBANKS 4
+#define BFIN_IWAYS 4
+#define BFIN_ILINES 32
#define WAY0_L 0x1
#define WAY1_L 0x2
#define AMGCTLVAL (V_AMBEN | V_AMCKEN | V_CDPRIO)
-#define MAX_VC 650000000
-#define MIN_VC 50000000
-
-#ifdef CONFIG_BFIN_KERNEL_CLOCK
-/********************************PLL Settings **************************************/
-#if (CONFIG_VCO_MULT < 0)
-#error "VCO Multiplier is less than 0. Please select a different value"
-#endif
-
-#if (CONFIG_VCO_MULT == 0)
-#error "VCO Multiplier should be greater than 0. Please select a different value"
-#endif
-
-#if (CONFIG_VCO_MULT > 64)
-#error "VCO Multiplier is more than 64. Please select a different value"
-#endif
-
-#ifndef CONFIG_CLKIN_HALF
-#define CONFIG_VCO_HZ (CONFIG_CLKIN_HZ * CONFIG_VCO_MULT)
-#else
-#define CONFIG_VCO_HZ ((CONFIG_CLKIN_HZ * CONFIG_VCO_MULT)/2)
-#endif
-
-#ifndef CONFIG_PLL_BYPASS
-#define CONFIG_CCLK_HZ (CONFIG_VCO_HZ/CONFIG_CCLK_DIV)
-#define CONFIG_SCLK_HZ (CONFIG_VCO_HZ/CONFIG_SCLK_DIV)
-#else
-#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ
-#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ
-#endif
-
-#if (CONFIG_SCLK_DIV < 1)
-#error "SCLK DIV cannot be less than 1 or more than 15. Please select a proper value"
-#endif
-
-#if (CONFIG_SCLK_DIV > 15)
-#error "SCLK DIV cannot be less than 1 or more than 15. Please select a proper value"
-#endif
-
-#if (CONFIG_CCLK_DIV != 1)
-#if (CONFIG_CCLK_DIV != 2)
-#if (CONFIG_CCLK_DIV != 4)
-#if (CONFIG_CCLK_DIV != 8)
-#error "CCLK DIV can be 1,2,4 or 8 only. Please select a proper value"
-#endif
-#endif
-#endif
-#endif
-
-#if (CONFIG_VCO_HZ > MAX_VC)
-#error "VCO selected is more than maximum value. Please change the VCO multipler"
-#endif
-
-#if (CONFIG_SCLK_HZ > 133000000)
-#error "Sclk value selected is more than maximum. Please select a proper value for SCLK multiplier"
-#endif
-
-#if (CONFIG_SCLK_HZ < 27000000)
-#error "Sclk value selected is less than minimum. Please select a proper value for SCLK multiplier"
-#endif
-
-#if (CONFIG_SCLK_HZ > CONFIG_CCLK_HZ)
-#if (CONFIG_SCLK_HZ != CONFIG_CLKIN_HZ)
-#if (CONFIG_CCLK_HZ != CONFIG_CLKIN_HZ)
-#error "Please select sclk less than cclk"
-#endif
-#endif
-#endif
-
-#if (CONFIG_CCLK_DIV == 1)
-#define CONFIG_CCLK_ACT_DIV CCLK_DIV1
-#endif
-#if (CONFIG_CCLK_DIV == 2)
-#define CONFIG_CCLK_ACT_DIV CCLK_DIV2
-#endif
-#if (CONFIG_CCLK_DIV == 4)
-#define CONFIG_CCLK_ACT_DIV CCLK_DIV4
-#endif
-#if (CONFIG_CCLK_DIV == 8)
-#define CONFIG_CCLK_ACT_DIV CCLK_DIV8
-#endif
-#ifndef CONFIG_CCLK_ACT_DIV
-#define CONFIG_CCLK_ACT_DIV CONFIG_CCLK_DIV_not_defined_properly
-#endif
-
-#if defined(ANOMALY_05000273) && (CONFIG_CCLK_DIV == 1)
-#error ANOMALY 05000273, please make sure CCLK is at least 2x SCLK
-#endif
-
-#endif /* CONFIG_BFIN_KERNEL_CLOCK */
-
#ifdef CONFIG_BF533
#define CPU "BF533"
#define CPUID 0x027a5000
#define CPUID 0x0
#endif
-#if (CONFIG_MEM_SIZE % 4)
-#error "SDRAM mem size must be multible of 4MB"
-#endif
-
-#define SDRAM_IGENERIC (CPLB_L1_CHBL | CPLB_USER_RD | CPLB_VALID | CPLB_PORTPRIO)
-#define SDRAM_IKERNEL (SDRAM_IGENERIC | CPLB_LOCK)
-#define L1_IMEMORY ( CPLB_USER_RD | CPLB_VALID | CPLB_LOCK)
-#define SDRAM_INON_CHBL ( CPLB_USER_RD | CPLB_VALID)
-
-/*Use the menuconfig cache policy here - CONFIG_BLKFIN_WT/CONFIG_BLKFIN_WB*/
-
-#define ANOMALY_05000158_WORKAROUND 0x200
-#ifdef CONFIG_BLKFIN_WB /*Write Back Policy */
-#define SDRAM_DGENERIC (CPLB_L1_CHBL | CPLB_DIRTY \
- | CPLB_SUPV_WR | CPLB_USER_WR | CPLB_USER_RD | CPLB_VALID | ANOMALY_05000158_WORKAROUND)
-#else /*Write Through */
-#define SDRAM_DGENERIC (CPLB_L1_CHBL | CPLB_WT | CPLB_L1_AOW | CPLB_DIRTY \
- | CPLB_SUPV_WR | CPLB_USER_WR | CPLB_USER_RD | CPLB_VALID | ANOMALY_05000158_WORKAROUND)
-#endif
-
-#define L1_DMEMORY (CPLB_SUPV_WR | CPLB_USER_WR | CPLB_USER_RD | CPLB_VALID | ANOMALY_05000158_WORKAROUND | CPLB_LOCK | CPLB_DIRTY)
-#define SDRAM_DNON_CHBL (CPLB_SUPV_WR | CPLB_USER_WR | CPLB_USER_RD | CPLB_VALID | ANOMALY_05000158_WORKAROUND | CPLB_DIRTY)
-#define SDRAM_EBIU (CPLB_SUPV_WR | CPLB_USER_WR | CPLB_USER_RD | CPLB_VALID | ANOMALY_05000158_WORKAROUND | CPLB_DIRTY)
-#define SDRAM_OOPS (CPLB_VALID | ANOMALY_05000158_WORKAROUND | CPLB_LOCK | CPLB_DIRTY)
-
-#define SIZE_1K 0x00000400 /* 1K */
-#define SIZE_4K 0x00001000 /* 4K */
-#define SIZE_1M 0x00100000 /* 1M */
-#define SIZE_4M 0x00400000 /* 4M */
-
-#define MAX_CPLBS (16 * 2)
-
-/*
-* Number of required data CPLB switchtable entries
-* MEMSIZE / 4 (we mostly install 4M page size CPLBs
-* approx 16 for smaller 1MB page size CPLBs for allignment purposes
-* 1 for L1 Data Memory
-* 1 for CONFIG_DEBUG_HUNT_FOR_ZERO
-* 1 for ASYNC Memory
-*/
-
-
-#define MAX_SWITCH_D_CPLBS (((CONFIG_MEM_SIZE / 4) + 16 + 1 + 1 + 1) * 2)
-
-/*
-* Number of required instruction CPLB switchtable entries
-* MEMSIZE / 4 (we mostly install 4M page size CPLBs
-* approx 12 for smaller 1MB page size CPLBs for allignment purposes
-* 1 for L1 Instruction Memory
-* 1 for CONFIG_DEBUG_HUNT_FOR_ZERO
-*/
-
-#define MAX_SWITCH_I_CPLBS (((CONFIG_MEM_SIZE / 4) + 12 + 1 + 1) * 2)
-
#endif /* __MACH_BF533_H__ */
#include "defBF532.h"
#include "anomaly.h"
-#if !(defined(__ASSEMBLY__) || defined(ASSEMBLY))
+#if !defined(__ASSEMBLY__)
#include "cdefBF532.h"
#endif
#ifndef _CDEF_BF532_H
#define _CDEF_BF532_H
-/*
-#if !defined(__ADSPLPBLACKFIN__)
-#warning cdefBF532.h should only be included for 532 compatible chips.
-#endif
-*/
+
+#include <asm/blackfin.h>
+
/*include all Core registers and bit definitions*/
#include "defBF532.h"
bfin_write32(SIC_IWR, IWR_ENABLE(0));
bfin_write16(VR_CTL, val);
- __builtin_bfin_ssync();
+ SSYNC();
local_irq_save(flags);
asm("IDLE;");
/* General Purpose IO (0xFFC0 2400-0xFFC0 27FF) */
#define bfin_read_FIO_DIR() bfin_read16(FIO_DIR)
#define bfin_write_FIO_DIR(val) bfin_write16(FIO_DIR,val)
-#define bfin_read_FIO_FLAG_C() bfin_read16(FIO_FLAG_C)
-#define bfin_write_FIO_FLAG_C(val) bfin_write16(FIO_FLAG_C,val)
-#define bfin_read_FIO_FLAG_S() bfin_read16(FIO_FLAG_S)
-#define bfin_write_FIO_FLAG_S(val) bfin_write16(FIO_FLAG_S,val)
#define bfin_read_FIO_MASKA_C() bfin_read16(FIO_MASKA_C)
#define bfin_write_FIO_MASKA_C(val) bfin_write16(FIO_MASKA_C,val)
#define bfin_read_FIO_MASKA_S() bfin_read16(FIO_MASKA_S)
#define bfin_write_FIO_BOTH(val) bfin_write16(FIO_BOTH,val)
#define bfin_read_FIO_INEN() bfin_read16(FIO_INEN)
#define bfin_write_FIO_INEN(val) bfin_write16(FIO_INEN,val)
-#define bfin_read_FIO_FLAG_D() bfin_read16(FIO_FLAG_D)
-#define bfin_write_FIO_FLAG_D(val) bfin_write16(FIO_FLAG_D,val)
-#define bfin_read_FIO_FLAG_T() bfin_read16(FIO_FLAG_T)
-#define bfin_write_FIO_FLAG_T(val) bfin_write16(FIO_FLAG_T,val)
#define bfin_read_FIO_MASKA_D() bfin_read16(FIO_MASKA_D)
#define bfin_write_FIO_MASKA_D(val) bfin_write16(FIO_MASKA_D,val)
#define bfin_read_FIO_MASKA_T() bfin_read16(FIO_MASKA_T)
#define bfin_read_FIO_MASKB_T() bfin_read16(FIO_MASKB_T)
#define bfin_write_FIO_MASKB_T(val) bfin_write16(FIO_MASKB_T,val)
+
+#if ANOMALY_05000311
+#define BFIN_WRITE_FIO_FLAG(name) \
+static __inline__ void bfin_write_FIO_FLAG_ ## name (unsigned short val)\
+{\
+ unsigned long flags;\
+ local_irq_save(flags);\
+ bfin_write16(FIO_FLAG_ ## name,val);\
+ bfin_read_CHIPID();\
+ local_irq_restore(flags);\
+}
+BFIN_WRITE_FIO_FLAG(D)
+BFIN_WRITE_FIO_FLAG(C)
+BFIN_WRITE_FIO_FLAG(S)
+BFIN_WRITE_FIO_FLAG(T)
+
+#define BFIN_READ_FIO_FLAG(name) \
+static __inline__ unsigned short bfin_read_FIO_FLAG_ ## name (void)\
+{\
+ unsigned long flags;\
+ unsigned short ret;\
+ local_irq_save(flags);\
+ ret = bfin_read16(FIO_FLAG_ ## name);\
+ bfin_read_CHIPID();\
+ local_irq_restore(flags);\
+ return ret;\
+}
+BFIN_READ_FIO_FLAG(D)
+BFIN_READ_FIO_FLAG(C)
+BFIN_READ_FIO_FLAG(S)
+BFIN_READ_FIO_FLAG(T)
+
+#else
+#define bfin_write_FIO_FLAG_D(val) bfin_write16(FIO_FLAG_D,val)
+#define bfin_write_FIO_FLAG_C(val) bfin_write16(FIO_FLAG_C,val)
+#define bfin_write_FIO_FLAG_S(val) bfin_write16(FIO_FLAG_S,val)
+#define bfin_write_FIO_FLAG_T(val) bfin_write16(FIO_FLAG_T,val)
+#define bfin_read_FIO_FLAG_T() bfin_read16(FIO_FLAG_T)
+#define bfin_read_FIO_FLAG_C() bfin_read16(FIO_FLAG_C)
+#define bfin_read_FIO_FLAG_S() bfin_read16(FIO_FLAG_S)
+#define bfin_read_FIO_FLAG_D() bfin_read16(FIO_FLAG_D)
+#endif
+
+
/* DMA Controller */
#define bfin_read_DMA0_CONFIG() bfin_read16(DMA0_CONFIG)
#define bfin_write_DMA0_CONFIG(val) bfin_write16(DMA0_CONFIG,val)
#define UART_GCTL 0xFFC00424 /* Global Control Register */
/* SPI Controller (0xFFC00500 - 0xFFC005FF) */
+#define SPI0_REGBASE 0xFFC00500
#define SPI_CTL 0xFFC00500 /* SPI Control Register */
#define SPI_FLG 0xFFC00504 /* SPI Flag register */
#define SPI_STAT 0xFFC00508 /* SPI Status register */
#define GM 0x00000008 /* When RDBR full, get more (=1) data or discard (=0) incoming Data */
#define PSSE 0x00000010 /* Enable (=1) Slave-Select input for Master. */
#define EMISO 0x00000020 /* Enable (=1) MISO pin as an output. */
-#define SPI_LEN 0x00000100 /* Word length (0 => 8 bits, 1 => 16 bits) */
+#define SIZE 0x00000100 /* Word length (0 => 8 bits, 1 => 16 bits) */
#define LSBF 0x00000200 /* Data format (0 => MSB sent/received first 1 => LSB sent/received first) */
#define CPHA 0x00000400 /* Clock phase (0 => SPICLK starts toggling in middle of xfer, 1 => SPICLK toggles at the beginning of xfer. */
#define CPOL 0x00000800 /* Clock polarity (0 => active-high, 1 => active-low) */
#define IRQ_PF14 47
#define IRQ_PF15 48
+#define GPIO_IRQ_BASE IRQ_PF0
+
#ifdef CONFIG_IRQCHIP_DEMUX_GPIO
#define NR_IRQS (IRQ_PF15+1)
#else
/* Level 1 Memory */
-#ifdef CONFIG_BLKFIN_CACHE
-#define BLKFIN_ICACHESIZE (16*1024)
+#ifdef CONFIG_BFIN_ICACHE
+#define BFIN_ICACHESIZE (16*1024)
#else
-#define BLKFIN_ICACHESIZE (0*1024)
+#define BFIN_ICACHESIZE (0*1024)
#endif
/* Memory Map for ADSP-BF533 processors */
#define L1_DATA_A_START 0xFF800000
#define L1_DATA_B_START 0xFF900000
-#ifdef CONFIG_BLKFIN_CACHE
+#ifdef CONFIG_BFIN_ICACHE
#define L1_CODE_LENGTH (0x14000 - 0x4000)
#else
#define L1_CODE_LENGTH 0x14000
#endif
-#ifdef CONFIG_BLKFIN_DCACHE
+#ifdef CONFIG_BFIN_DCACHE
-#ifdef CONFIG_BLKFIN_DCACHE_BANKA
+#ifdef CONFIG_BFIN_DCACHE_BANKA
#define DMEM_CNTR (ACACHE_BSRAM | ENDCPLB | PORT_PREF0)
#define L1_DATA_A_LENGTH (0x8000 - 0x4000)
#define L1_DATA_B_LENGTH 0x8000
-#define BLKFIN_DCACHESIZE (16*1024)
-#define BLKFIN_DSUPBANKS 1
+#define BFIN_DCACHESIZE (16*1024)
+#define BFIN_DSUPBANKS 1
#else
#define DMEM_CNTR (ACACHE_BCACHE | ENDCPLB | PORT_PREF0)
#define L1_DATA_A_LENGTH (0x8000 - 0x4000)
#define L1_DATA_B_LENGTH (0x8000 - 0x4000)
-#define BLKFIN_DCACHESIZE (32*1024)
-#define BLKFIN_DSUPBANKS 2
+#define BFIN_DCACHESIZE (32*1024)
+#define BFIN_DSUPBANKS 2
#endif
#else
#define DMEM_CNTR (ASRAM_BSRAM | ENDCPLB | PORT_PREF0)
#define L1_DATA_A_LENGTH 0x8000
#define L1_DATA_B_LENGTH 0x8000
-#define BLKFIN_DCACHESIZE (0*1024)
-#define BLKFIN_DSUPBANKS 0
-#endif /*CONFIG_BLKFIN_DCACHE*/
+#define BFIN_DCACHESIZE (0*1024)
+#define BFIN_DSUPBANKS 0
+#endif /*CONFIG_BFIN_DCACHE*/
#endif
/* Memory Map for ADSP-BF532 processors */
#define L1_DATA_A_START 0xFF804000
#define L1_DATA_B_START 0xFF904000
-#ifdef CONFIG_BLKFIN_CACHE
+#ifdef CONFIG_BFIN_ICACHE
#define L1_CODE_LENGTH (0xC000 - 0x4000)
#else
#define L1_CODE_LENGTH 0xC000
#endif
-#ifdef CONFIG_BLKFIN_DCACHE
+#ifdef CONFIG_BFIN_DCACHE
-#ifdef CONFIG_BLKFIN_DCACHE_BANKA
+#ifdef CONFIG_BFIN_DCACHE_BANKA
#define DMEM_CNTR (ACACHE_BSRAM | ENDCPLB | PORT_PREF0)
#define L1_DATA_A_LENGTH (0x4000 - 0x4000)
#define L1_DATA_B_LENGTH 0x4000
-#define BLKFIN_DCACHESIZE (16*1024)
-#define BLKFIN_DSUPBANKS 1
+#define BFIN_DCACHESIZE (16*1024)
+#define BFIN_DSUPBANKS 1
#else
#define DMEM_CNTR (ACACHE_BCACHE | ENDCPLB | PORT_PREF0)
#define L1_DATA_A_LENGTH (0x4000 - 0x4000)
#define L1_DATA_B_LENGTH (0x4000 - 0x4000)
-#define BLKFIN_DCACHESIZE (32*1024)
-#define BLKFIN_DSUPBANKS 2
+#define BFIN_DCACHESIZE (32*1024)
+#define BFIN_DSUPBANKS 2
#endif
#else
#define DMEM_CNTR (ASRAM_BSRAM | ENDCPLB | PORT_PREF0)
#define L1_DATA_A_LENGTH 0x4000
#define L1_DATA_B_LENGTH 0x4000
-#define BLKFIN_DCACHESIZE (0*1024)
-#define BLKFIN_DSUPBANKS 0
-#endif /*CONFIG_BLKFIN_DCACHE*/
+#define BFIN_DCACHESIZE (0*1024)
+#define BFIN_DSUPBANKS 0
+#endif /*CONFIG_BFIN_DCACHE*/
#endif
/* Memory Map for ADSP-BF531 processors */
#define L1_DATA_B_LENGTH 0x0000
-#ifdef CONFIG_BLKFIN_DCACHE
+#ifdef CONFIG_BFIN_DCACHE
#define DMEM_CNTR (ACACHE_BSRAM | ENDCPLB | PORT_PREF0)
#define L1_DATA_A_LENGTH (0x4000 - 0x4000)
-#define BLKFIN_DCACHESIZE (16*1024)
-#define BLKFIN_DSUPBANKS 1
+#define BFIN_DCACHESIZE (16*1024)
+#define BFIN_DSUPBANKS 1
#else
#define DMEM_CNTR (ASRAM_BSRAM | ENDCPLB | PORT_PREF0)
#define L1_DATA_A_LENGTH 0x4000
-#define BLKFIN_DCACHESIZE (0*1024)
-#define BLKFIN_DSUPBANKS 0
+#define BFIN_DCACHESIZE (0*1024)
+#define BFIN_DSUPBANKS 0
#endif
#endif
-
/*
- * File: include/asm-blackfin/mach-bf537/anomaly.h
- * Based on:
- * Author:
- *
- * Created:
- * Description:
- *
- * Rev:
- *
- * Modified:
- *
- *
- * Bugs: Enter bugs at http://blackfin.uclinux.org/
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2, or (at your option)
- * any later version.
+ * File: include/asm-blackfin/mach-bf537/anomaly.h
+ * Bugs: Enter bugs at http://blackfin.uclinux.org/
*
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; see the file COPYING.
- * If not, write to the Free Software Foundation,
- * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ * Copyright (C) 2004-2007 Analog Devices Inc.
+ * Licensed under the GPL-2 or later.
*/
/* This file shoule be up to date with:
- * - Revision J, June 1, 2006; ADSP-BF537 Blackfin Processor Anomaly List
- * - Revision I, June 1, 2006; ADSP-BF536 Blackfin Processor Anomaly List
- * - Revision J, June 1, 2006; ADSP-BF534 Blackfin Processor Anomaly List
+ * - Revision M, March 13, 2007; ADSP-BF537 Blackfin Processor Anomaly List
+ * - Revision L, March 13, 2007; ADSP-BF536 Blackfin Processor Anomaly List
+ * - Revision M, March 13, 2007; ADSP-BF534 Blackfin Processor Anomaly List
*/
#ifndef _MACH_ANOMALY_H_
#define _MACH_ANOMALY_H_
/* We do not support 0.1 silicon - sorry */
-#if (defined(CONFIG_BF_REV_0_1))
-#error Kernel will not work on BF537/6/4 Version 0.1
+#if __SILICON_REVISION__ < 2
+# error Kernel will not work on BF537 silicon version 0.0 or 0.1
#endif
-#if (defined(CONFIG_BF_REV_0_3) || defined(CONFIG_BF_REV_0_2))
-#define ANOMALY_05000074 /* A multi issue instruction with dsp32shiftimm in
- slot1 and store of a P register in slot 2 is not
- supported */
-#define ANOMALY_05000119 /* DMA_RUN bit is not valid after a Peripheral Receive
- Channel DMA stops */
-#define ANOMALY_05000122 /* Rx.H can not be used to access 16-bit System MMR
- registers. */
-#define ANOMALY_05000166 /* PPI Data Lengths Between 8 and 16 do not zero out
- upper bits*/
-#define ANOMALY_05000180 /* PPI_DELAY not functional in PPI modes with 0 frame
- syncs */
-#if (defined(CONFIG_BF537) || defined(CONFIG_BF536))
-#define ANOMALY_05000247 /* CLKIN Buffer Output Enable Reset Behavior Is
- Changed */
-#endif
-#define ANOMALY_05000265 /* Sensitivity to noise with slow input edge rates on
- SPORT external receive and transmit clocks. */
-#define ANOMALY_05000272 /* Certain data cache write through modes fail for
- VDDint <=0.9V */
-#define ANOMALY_05000273 /* Writes to Synchronous SDRAM memory may be lost */
-#define ANOMALY_05000277 /* Writes to a flag data register one SCLK cycle after
- an edge is detected may clear interrupt */
-#define ANOMALY_05000281 /* False Hardware Error Exception when ISR context is
- not restored */
-#define ANOMALY_05000282 /* Memory DMA corruption with 32-bit data and traffic
- control */
-#define ANOMALY_05000283 /* A system MMR write is stalled indefinitely when
- killed in a particular stage*/
-#define ANOMALY_05000310 /* False hardware errors caused by fetches at the
- * boundary of reserved memory */
-#define ANOMALY_05000312 /* Errors when SSYNC, CSYNC, or loads to LT, LB and LC
- registers are interrupted */
-#define ANOMALY_05000313 /* PPI is level sensitive on first transfer */
-#define ANOMALY_05000322 /* EMAC RMII mode at 10-Base-T speed: RX frames not
- * received properly */
+#if defined(__ADSPBF534__)
+# define ANOMALY_BF534 1
+#else
+# define ANOMALY_BF534 0
#endif
-
-#if defined(CONFIG_BF_REV_0_2)
-#define ANOMALY_05000244 /* With instruction cache enabled, a CSYNC or SSYNC or
- IDLE around a Change of Control causes
- unpredictable results */
-#define ANOMALY_05000250 /* Incorrect Bit-Shift of Data Word in Multichannel
- (TDM) */
-#if (defined(CONFIG_BF537) || defined(CONFIG_BF536))
-#define ANOMALY_05000252 /* EMAC Tx DMA error after an early frame abort */
+#if defined(__ADSPBF536__)
+# define ANOMALY_BF536 1
+#else
+# define ANOMALY_BF536 0
#endif
-#define ANOMALY_05000253 /* Maximum external clock speed for Timers */
-#define ANOMALY_05000255 /* Entering Hibernate Mode with RTC Seconds event
- interrupt not functional */
-#if (defined(CONFIG_BF537) || defined(CONFIG_BF536))
-#define ANOMALY_05000256 /* EMAC MDIO input latched on wrong MDC edge */
+#if defined(__ADSPBF537__)
+# define ANOMALY_BF537 1
+#else
+# define ANOMALY_BF537 0
#endif
-#define ANOMALY_05000257 /* An interrupt or exception during short Hardware
- loops may cause the instruction fetch unit to
- malfunction */
-#define ANOMALY_05000258 /* Instruction Cache is corrupted when bit 9 and 12 of
- the ICPLB Data registers differ */
-#define ANOMALY_05000260 /* ICPLB_STATUS MMR register may be corrupted */
-#define ANOMALY_05000261 /* DCPLB_FAULT_ADDR MMR register may be corrupted */
-#define ANOMALY_05000262 /* Stores to data cache may be lost */
-#define ANOMALY_05000263 /* Hardware loop corrupted when taking an ICPLB exception */
-#define ANOMALY_05000264 /* A Sync instruction (CSYNC, SSYNC) or an IDLE
- instruction will cause an infinite stall in the
- second to last instruction in a hardware loop */
-#define ANOMALY_05000268 /* Memory DMA error when peripheral DMA is running
- and non-zero DEB_TRAFFIC_PERIOD value */
-#define ANOMALY_05000270 /* High I/O activity causes the output voltage of the
- internal voltage regulator (VDDint) to decrease */
-#define ANOMALY_05000277 /* Writes to a flag data register one SCLK cycle after
- an edge is detected may clear interrupt */
-#define ANOMALY_05000278 /* Disabling Peripherals with DMA running may cause
- DMA system instability */
-#define ANOMALY_05000280 /* SPI Master boot mode does not work well with
- Atmel Dataflash devices */
-#define ANOMALY_05000281 /* False Hardware Error Exception when ISR context
- * is not restored */
-#define ANOMALY_05000282 /* Memory DMA corruption with 32-bit data and traffic
- * control */
-#define ANOMALY_05000283 /* System MMR Write Is Stalled Indefinitely When
- * Killed in a Particular Stage */
-#define ANOMALY_05000285 /* New Feature: EMAC TX DMA Word Alignment
- * (Not Available On Older Silicon) */
-#define ANOMALY_05000288 /* SPORTs may receive bad data if FIFOs fill up */
-#define ANOMALY_05000315 /* Killed System MMR Write Completes Erroneously
- * On Next System MMR Access */
-#define ANOMALY_05000316 /* EMAC RMII mode: collisions occur in Full Duplex
- * mode */
-#define ANOMALY_05000321 /* EMAC RMII mode: TX frames in half duplex fail with
- * status No Carrier */
-#endif /* CONFIG_BF_REV_0_2 */
-#endif /* _MACH_ANOMALY_H_ */
+/* Multi-issue instruction with dsp32shiftimm in slot1 and P-reg store in slot 2 not supported */
+#define ANOMALY_05000074 (1)
+/* DMA_RUN bit is not valid after a Peripheral Receive Channel DMA stops */
+#define ANOMALY_05000119 (1)
+/* Rx.H cannot be used to access 16-bit System MMR registers */
+#define ANOMALY_05000122 (1)
+/* Killed 32-bit MMR write leads to next system MMR access thinking it should be 32-bit */
+#define ANOMALY_05000157 (__SILICON_REVISION__ < 2)
+/* PPI_DELAY not functional in PPI modes with 0 frame syncs */
+#define ANOMALY_05000180 (1)
+/* Instruction Cache Is Not Functional */
+#define ANOMALY_05000237 (__SILICON_REVISION__ < 2)
+/* If i-cache is on, CSYNC/SSYNC/IDLE around Change of Control causes failures */
+#define ANOMALY_05000244 (__SILICON_REVISION__ < 3)
+/* Spurious Hardware Error from an access in the shadow of a conditional branch */
+#define ANOMALY_05000245 (1)
+/* CLKIN Buffer Output Enable Reset Behavior Is Changed */
+#define ANOMALY_05000247 (1)
+/* Incorrect Bit-Shift of Data Word in Multichannel (TDM) mode in certain conditions */
+#define ANOMALY_05000250 (__SILICON_REVISION__ < 3)
+/* EMAC Tx DMA error after an early frame abort */
+#define ANOMALY_05000252 (__SILICON_REVISION__ < 3)
+/* Maximum external clock speed for Timers */
+#define ANOMALY_05000253 (__SILICON_REVISION__ < 3)
+/* Incorrect Timer Pulse Width in Single-Shot PWM_OUT mode with external clock */
+#define ANOMALY_05000254 (__SILICON_REVISION__ > 2)
+/* Entering Hibernate Mode with RTC Seconds event interrupt not functional */
+#define ANOMALY_05000255 (__SILICON_REVISION__ < 3)
+/* EMAC MDIO input latched on wrong MDC edge */
+#define ANOMALY_05000256 (__SILICON_REVISION__ < 3)
+/* Interrupt/Exception during short hardware loop may cause bad instruction fetches */
+#define ANOMALY_05000257 (__SILICON_REVISION__ < 3)
+/* Instruction Cache is corrupted when bits 9 and 12 of the ICPLB Data registers differ */
+#define ANOMALY_05000258 (((ANOMALY_BF536 || ANOMALY_BF537) && __SILICON_REVISION__ == 1) || __SILICON_REVISION__ == 2)
+/* ICPLB_STATUS MMR register may be corrupted */
+#define ANOMALY_05000260 (__SILICON_REVISION__ == 2)
+/* DCPLB_FAULT_ADDR MMR register may be corrupted */
+#define ANOMALY_05000261 (__SILICON_REVISION__ < 3)
+/* Stores to data cache may be lost */
+#define ANOMALY_05000262 (__SILICON_REVISION__ < 3)
+/* Hardware loop corrupted when taking an ICPLB exception */
+#define ANOMALY_05000263 (__SILICON_REVISION__ == 2)
+/* CSYNC/SSYNC/IDLE causes infinite stall in second to last instruction in hardware loop */
+#define ANOMALY_05000264 (__SILICON_REVISION__ < 3)
+/* Sensitivity to noise with slow input edge rates on external SPORT TX and RX clocks */
+#define ANOMALY_05000265 (1)
+/* Memory DMA error when peripheral DMA is running with non-zero DEB_TRAFFIC_PERIOD */
+#define ANOMALY_05000268 (__SILICON_REVISION__ < 3)
+/* High I/O activity causes output voltage of internal voltage regulator (VDDint) to decrease */
+#define ANOMALY_05000270 (__SILICON_REVISION__ < 3)
+/* Certain data cache write through modes fail for VDDint <=0.9V */
+#define ANOMALY_05000272 (1)
+/* Writes to Synchronous SDRAM memory may be lost */
+#define ANOMALY_05000273 (__SILICON_REVISION__ < 3)
+/* Writes to an I/O data register one SCLK cycle after an edge is detected may clear interrupt */
+#define ANOMALY_05000277 (__SILICON_REVISION__ < 3)
+/* Disabling Peripherals with DMA running may cause DMA system instability */
+#define ANOMALY_05000278 (((ANOMALY_BF536 || ANOMALY_BF537) && __SILICON_REVISION__ < 3) || (ANOMALY_BF534 && __SILICON_REVISION__ < 2))
+/* SPI Master boot mode does not work well with Atmel Data flash devices */
+#define ANOMALY_05000280 (1)
+/* False Hardware Error Exception when ISR context is not restored */
+#define ANOMALY_05000281 (__SILICON_REVISION__ < 3)
+/* Memory DMA corruption with 32-bit data and traffic control */
+#define ANOMALY_05000282 (__SILICON_REVISION__ < 3)
+/* System MMR Write Is Stalled Indefinitely When Killed in a Particular Stage */
+#define ANOMALY_05000283 (__SILICON_REVISION__ < 3)
+/* New Feature: EMAC TX DMA Word Alignment (Not Available On Older Silicon) */
+#define ANOMALY_05000285 (__SILICON_REVISION__ < 3)
+/* SPORTs may receive bad data if FIFOs fill up */
+#define ANOMALY_05000288 (__SILICON_REVISION__ < 3)
+/* Memory to memory DMA source/destination descriptors must be in same memory space */
+#define ANOMALY_05000301 (1)
+/* SSYNCs After Writes To CAN/DMA MMR Registers Are Not Always Handled Correctly */
+#define ANOMALY_05000304 (__SILICON_REVISION__ < 3)
+/* New Feature: Additional Hysteresis on SPORT Input Pins (Not Available On Older Silicon) */
+#define ANOMALY_05000305 (__SILICON_REVISION__ < 3)
+/* SCKELOW Bit Does Not Maintain State Through Hibernate */
+#define ANOMALY_05000307 (__SILICON_REVISION__ < 3)
+/* Writing UART_THR while UART clock is disabled sends erroneous start bit */
+#define ANOMALY_05000309 (__SILICON_REVISION__ < 3)
+/* False hardware errors caused by fetches at the boundary of reserved memory */
+#define ANOMALY_05000310 (1)
+/* Errors when SSYNC, CSYNC, or loads to LT, LB and LC registers are interrupted */
+#define ANOMALY_05000312 (1)
+/* PPI is level sensitive on first transfer */
+#define ANOMALY_05000313 (1)
+/* Killed System MMR Write Completes Erroneously On Next System MMR Access */
+#define ANOMALY_05000315 (__SILICON_REVISION__ < 3)
+/* EMAC RMII mode: collisions occur in Full Duplex mode */
+#define ANOMALY_05000316 (__SILICON_REVISION__ < 3)
+/* EMAC RMII mode: TX frames in half duplex fail with status No Carrier */
+#define ANOMALY_05000321 (__SILICON_REVISION__ < 3)
+/* EMAC RMII mode at 10-Base-T speed: RX frames not received properly */
+#define ANOMALY_05000322 (1)
+
+/* Anomalies that don't exist on this proc */
+#define ANOMALY_05000125 (0)
+#define ANOMALY_05000158 (0)
+#define ANOMALY_05000183 (0)
+#define ANOMALY_05000198 (0)
+#define ANOMALY_05000230 (0)
+#define ANOMALY_05000266 (0)
+#define ANOMALY_05000311 (0)
+#define ANOMALY_05000323 (0)
+
+#endif
/***************************/
-#define BLKFIN_DSUBBANKS 4
-#define BLKFIN_DWAYS 2
-#define BLKFIN_DLINES 64
-#define BLKFIN_ISUBBANKS 4
-#define BLKFIN_IWAYS 4
-#define BLKFIN_ILINES 32
+#define BFIN_DSUBBANKS 4
+#define BFIN_DWAYS 2
+#define BFIN_DLINES 64
+#define BFIN_ISUBBANKS 4
+#define BFIN_IWAYS 4
+#define BFIN_ILINES 32
#define WAY0_L 0x1
#define WAY1_L 0x2
#define AMGCTLVAL (V_AMBEN | V_AMCKEN | V_CDPRIO)
-#define MAX_VC 650000000
-#define MIN_VC 50000000
-
-/********************************PLL Settings **************************************/
-#ifdef CONFIG_BFIN_KERNEL_CLOCK
-#if (CONFIG_VCO_MULT < 0)
-#error "VCO Multiplier is less than 0. Please select a different value"
-#endif
-
-#if (CONFIG_VCO_MULT == 0)
-#error "VCO Multiplier should be greater than 0. Please select a different value"
-#endif
-
-#if (CONFIG_VCO_MULT > 64)
-#error "VCO Multiplier is more than 64. Please select a different value"
-#endif
-
-#ifndef CONFIG_CLKIN_HALF
-#define CONFIG_VCO_HZ (CONFIG_CLKIN_HZ * CONFIG_VCO_MULT)
-#else
-#define CONFIG_VCO_HZ ((CONFIG_CLKIN_HZ * CONFIG_VCO_MULT)/2)
-#endif
-
-#ifndef CONFIG_PLL_BYPASS
-#define CONFIG_CCLK_HZ (CONFIG_VCO_HZ/CONFIG_CCLK_DIV)
-#define CONFIG_SCLK_HZ (CONFIG_VCO_HZ/CONFIG_SCLK_DIV)
-#else
-#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ
-#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ
-#endif
-
-#if (CONFIG_SCLK_DIV < 1)
-#error "SCLK DIV cannot be less than 1 or more than 15. Please select a proper value"
-#endif
-
-#if (CONFIG_SCLK_DIV > 15)
-#error "SCLK DIV cannot be less than 1 or more than 15. Please select a proper value"
-#endif
-
-#if (CONFIG_CCLK_DIV != 1)
-#if (CONFIG_CCLK_DIV != 2)
-#if (CONFIG_CCLK_DIV != 4)
-#if (CONFIG_CCLK_DIV != 8)
-#error "CCLK DIV can be 1,2,4 or 8 only. Please select a proper value"
-#endif
-#endif
-#endif
-#endif
-
-#if (CONFIG_VCO_HZ > MAX_VC)
-#error "VCO selected is more than maximum value. Please change the VCO multipler"
-#endif
-
-#if (CONFIG_SCLK_HZ > 133000000)
-#error "Sclk value selected is more than maximum. Please select a proper value for SCLK multiplier"
-#endif
-
-#if (CONFIG_SCLK_HZ < 27000000)
-#error "Sclk value selected is less than minimum. Please select a proper value for SCLK multiplier"
-#endif
-
-#if (CONFIG_SCLK_HZ >= CONFIG_CCLK_HZ)
-#if (CONFIG_SCLK_HZ != CONFIG_CLKIN_HZ)
-#if (CONFIG_CCLK_HZ != CONFIG_CLKIN_HZ)
-#error "Please select sclk less than cclk"
-#endif
-#endif
-#endif
-
-#if (CONFIG_CCLK_DIV == 1)
-#define CONFIG_CCLK_ACT_DIV CCLK_DIV1
-#endif
-#if (CONFIG_CCLK_DIV == 2)
-#define CONFIG_CCLK_ACT_DIV CCLK_DIV2
-#endif
-#if (CONFIG_CCLK_DIV == 4)
-#define CONFIG_CCLK_ACT_DIV CCLK_DIV4
-#endif
-#if (CONFIG_CCLK_DIV == 8)
-#define CONFIG_CCLK_ACT_DIV CCLK_DIV8
-#endif
-#ifndef CONFIG_CCLK_ACT_DIV
-#define CONFIG_CCLK_ACT_DIV CONFIG_CCLK_DIV_not_defined_properly
-#endif
-
-#if defined(ANOMALY_05000273) && (CONFIG_CCLK_DIV == 1)
-#error ANOMALY 05000273, please make sure CCLK is at least 2x SCLK
-#endif
-
-#endif /* CONFIG_BFIN_KERNEL_CLOCK */
-
#ifdef CONFIG_BF537
#define CPU "BF537"
#define CPUID 0x027c8000
#define CPUID 0x0
#endif
-#if (CONFIG_MEM_SIZE % 4)
-#error "SDRAM mem size must be multible of 4MB"
-#endif
-
-#define SDRAM_IGENERIC (CPLB_L1_CHBL | CPLB_USER_RD | CPLB_VALID | CPLB_PORTPRIO)
-#define SDRAM_IKERNEL (SDRAM_IGENERIC | CPLB_LOCK)
-#define L1_IMEMORY ( CPLB_USER_RD | CPLB_VALID | CPLB_LOCK)
-#define SDRAM_INON_CHBL ( CPLB_USER_RD | CPLB_VALID)
-
-/*Use the menuconfig cache policy here - CONFIG_BLKFIN_WT/CONFIG_BLKFIN_WB*/
-
-#define ANOMALY_05000158_WORKAROUND 0x200
-#ifdef CONFIG_BLKFIN_WB /*Write Back Policy */
-#define SDRAM_DGENERIC (CPLB_L1_CHBL | CPLB_DIRTY \
- | CPLB_SUPV_WR | CPLB_USER_WR | CPLB_USER_RD | CPLB_VALID | ANOMALY_05000158_WORKAROUND)
-#else /*Write Through */
-#define SDRAM_DGENERIC (CPLB_L1_CHBL | CPLB_WT | CPLB_L1_AOW \
- | CPLB_SUPV_WR | CPLB_USER_WR | CPLB_USER_RD | CPLB_VALID | ANOMALY_05000158_WORKAROUND | CPLB_DIRTY )
-#endif
-
-
-#define L1_DMEMORY (CPLB_SUPV_WR | CPLB_USER_WR | CPLB_USER_RD | CPLB_VALID | ANOMALY_05000158_WORKAROUND | CPLB_LOCK | CPLB_DIRTY )
-#define SDRAM_DNON_CHBL (CPLB_SUPV_WR | CPLB_USER_WR | CPLB_USER_RD | CPLB_VALID | ANOMALY_05000158_WORKAROUND | CPLB_DIRTY )
-#define SDRAM_EBIU (CPLB_SUPV_WR | CPLB_USER_WR | CPLB_USER_RD | CPLB_VALID | ANOMALY_05000158_WORKAROUND | CPLB_DIRTY )
-#define SDRAM_OOPS (CPLB_VALID | ANOMALY_05000158_WORKAROUND | CPLB_LOCK | CPLB_DIRTY )
-
-#define SIZE_1K 0x00000400 /* 1K */
-#define SIZE_4K 0x00001000 /* 4K */
-#define SIZE_1M 0x00100000 /* 1M */
-#define SIZE_4M 0x00400000 /* 4M */
-
-#define MAX_CPLBS (16 * 2)
-
-/*
-* Number of required data CPLB switchtable entries
-* MEMSIZE / 4 (we mostly install 4M page size CPLBs
-* approx 16 for smaller 1MB page size CPLBs for allignment purposes
-* 1 for L1 Data Memory
-* 1 for CONFIG_DEBUG_HUNT_FOR_ZERO
-* 1 for ASYNC Memory
-*/
-
-
-#define MAX_SWITCH_D_CPLBS (((CONFIG_MEM_SIZE / 4) + 16 + 1 + 1 + 1) * 2)
-
-/*
-* Number of required instruction CPLB switchtable entries
-* MEMSIZE / 4 (we mostly install 4M page size CPLBs
-* approx 12 for smaller 1MB page size CPLBs for allignment purposes
-* 1 for L1 Instruction Memory
-* 1 for CONFIG_DEBUG_HUNT_FOR_ZERO
-*/
-
-#define MAX_SWITCH_I_CPLBS (((CONFIG_MEM_SIZE / 4) + 12 + 1 + 1) * 2)
-
#endif /* __MACH_BF537_H__ */
#include "defBF537.h"
#endif
-#if !(defined(__ASSEMBLY__) || defined(ASSEMBLY))
+#if !defined(__ASSEMBLY__)
#include "cdefBF534.h"
/* UART 0*/
#define bfin_write_STOPCK_OFF(val) bfin_write_STOPCK(val)
#define STOPCK_OFF STOPCK
-/* FIO USE PORT F*/
-#ifdef CONFIG_BF537_PORT_F
-#define bfin_read_PORT_FER() bfin_read_PORTF_FER()
-#define bfin_write_PORT_FER(val) bfin_write_PORTF_FER(val)
-#define bfin_read_FIO_FLAG_D() bfin_read_PORTFIO()
-#define bfin_write_FIO_FLAG_D(val) bfin_write_PORTFIO(val)
-#define bfin_read_FIO_FLAG_C() bfin_read_PORTFIO_CLEAR()
-#define bfin_write_FIO_FLAG_C(val) bfin_write_PORTFIO_CLEAR(val)
-#define bfin_read_FIO_FLAG_S() bfin_read_PORTFIO_SET()
-#define bfin_write_FIO_FLAG_S(val) bfin_write_PORTFIO_SET(val)
-#define bfin_read_FIO_FLAG_T() bfin_read_PORTFIO_TOGGLE()
-#define bfin_write_FIO_FLAG_T(val) bfin_write_PORTFIO_TOGGLE(val)
-#define bfin_read_FIO_MASKA_D() bfin_read_PORTFIO_MASKA()
-#define bfin_write_FIO_MASKA_D(val) bfin_write_PORTFIO_MASKA(val)
-#define bfin_read_FIO_MASKA_C() bfin_read_PORTFIO_MASKA_CLEAR()
-#define bfin_write_FIO_MASKA_C(val) bfin_write_PORTFIO_MASKA_CLEAR(val)
-#define bfin_read_FIO_MASKA_S() bfin_read_PORTFIO_MASKA_SET()
-#define bfin_write_FIO_MASKA_S(val) bfin_write_PORTFIO_MASKA_SET(val)
-#define bfin_read_FIO_MASKA_T() bfin_read_PORTFIO_MASKA_TOGGLE()
-#define bfin_write_FIO_MASKA_T(val) bfin_write_PORTFIO_MASKA_TOGGLE(val)
-#define bfin_read_FIO_MASKB_D() bfin_read_PORTFIO_MASKB()
-#define bfin_write_FIO_MASKB_D(val) bfin_write_PORTFIO_MASKB(val)
-#define bfin_read_FIO_MASKB_C() bfin_read_PORTFIO_MASKB_CLEAR()
-#define bfin_write_FIO_MASKB_C(val) bfin_write_PORTFIO_MASKB_CLEAR(val)
-#define bfin_read_FIO_MASKB_S() bfin_read_PORTFIO_MASKB_SET()
-#define bfin_write_FIO_MASKB_S(val) bfin_write_PORTFIO_MASKB_SET(val)
-#define bfin_read_FIO_MASKB_T() bfin_read_PORTFIO_MASKB_TOGGLE()
-#define bfin_write_FIO_MASKB_T(val) bfin_write_PORTFIO_MASKB_TOGGLE(val)
-#define bfin_read_FIO_DIR() bfin_read_PORTFIO_DIR()
-#define bfin_write_FIO_DIR(val) bfin_write_PORTFIO_DIR(val)
-#define bfin_read_FIO_POLAR() bfin_read_PORTFIO_POLAR()
-#define bfin_write_FIO_POLAR(val) bfin_write_PORTFIO_POLAR(val)
-#define bfin_read_FIO_EDGE() bfin_read_PORTFIO_EDGE()
-#define bfin_write_FIO_EDGE(val) bfin_write_PORTFIO_EDGE(val)
-#define bfin_read_FIO_BOTH() bfin_read_PORTFIO_BOTH()
-#define bfin_write_FIO_BOTH(val) bfin_write_PORTFIO_BOTH(val)
-#define bfin_read_FIO_INEN() bfin_read_PORTFIO_INEN()
-#define bfin_write_FIO_INEN(val) bfin_write_PORTFIO_INEN(val)
-
-#define bfin_read_FIO_FLAG_D() bfin_read_PORTFIO()
-#define bfin_write_FIO_FLAG_D(val) bfin_write_PORTFIO(val)
-#define FIO_FLAG_D PORTFIO
-#define bfin_read_FIO_FLAG_C() bfin_read_PORTFIO_CLEAR()
-#define bfin_write_FIO_FLAG_C(val) bfin_write_PORTFIO_CLEAR(val)
-#define FIO_FLAG_C PORTFIO_CLEAR
-#define bfin_read_FIO_FLAG_S() bfin_read_PORTFIO_SET()
-#define bfin_write_FIO_FLAG_S(val) bfin_write_PORTFIO_SET(val)
-#define FIO_FLAG_S PORTFIO_SET
-#define bfin_read_FIO_FLAG_T() bfin_read_PORTFIO_TOGGLE()
-#define bfin_write_FIO_FLAG_T(val) bfin_write_PORTFIO_TOGGLE(val)
-#define FIO_FLAG_T PORTFIO_TOGGLE
-#define bfin_read_FIO_MASKA_D() bfin_read_PORTFIO_MASKA()
-#define bfin_write_FIO_MASKA_D(val) bfin_write_PORTFIO_MASKA(val)
-#define FIO_MASKA_D PORTFIO_MASKA
-#define bfin_read_FIO_MASKA_C() bfin_read_PORTFIO_MASKA_CLEAR()
-#define bfin_write_FIO_MASKA_C(val) bfin_write_PORTFIO_MASKA_CLEAR(val)
-#define FIO_MASKA_C PORTFIO_MASKA_CLEAR
-#define bfin_read_FIO_MASKA_S() bfin_read_PORTFIO_MASKA_SET()
-#define bfin_write_FIO_MASKA_S(val) bfin_write_PORTFIO_MASKA_SET(val)
-#define FIO_MASKA_S PORTFIO_MASKA_SET
-#define bfin_read_FIO_MASKA_T() bfin_read_PORTFIO_MASKA_TOGGLE()
-#define bfin_write_FIO_MASKA_T(val) bfin_write_PORTFIO_MASKA_TOGGLE(val)
-#define FIO_MASKA_T PORTFIO_MASKA_TOGGLE
-#define bfin_read_FIO_MASKB_D() bfin_read_PORTFIO_MASKB()
-#define bfin_write_FIO_MASKB_D(val) bfin_write_PORTFIO_MASKB(val)
-#define FIO_MASKB_D PORTFIO_MASKB
-#define bfin_read_FIO_MASKB_C() bfin_read_PORTFIO_MASKB_CLEAR()
-#define bfin_write_FIO_MASKB_C(val) bfin_write_PORTFIO_MASKB_CLEAR(val)
-#define FIO_MASKB_C PORTFIO_MASKB_CLEAR
-#define bfin_read_FIO_MASKB_S() bfin_read_PORTFIO_MASKB_SET()
-#define bfin_write_FIO_MASKB_S(val) bfin_write_PORTFIO_MASKB_SET(val)
-#define FIO_MASKB_S PORTFIO_MASKB_SET
-#define bfin_read_FIO_MASKB_T() bfin_read_PORTFIO_MASKB_TOGGLE()
-#define bfin_write_FIO_MASKB_T(val) bfin_write_PORTFIO_MASKB_TOGGLE(val)
-#define FIO_MASKB_T PORTFIO_MASKB_TOGGLE
-#define bfin_read_FIO_DIR() bfin_read_PORTFIO_DIR()
-#define bfin_write_FIO_DIR(val) bfin_write_PORTFIO_DIR(val)
-#define FIO_DIR PORTFIO_DIR
-#define bfin_read_FIO_POLAR() bfin_read_PORTFIO_POLAR()
-#define bfin_write_FIO_POLAR(val) bfin_write_PORTFIO_POLAR(val)
-#define FIO_POLAR PORTFIO_POLAR
-#define bfin_read_FIO_EDGE() bfin_read_PORTFIO_EDGE()
-#define bfin_write_FIO_EDGE(val) bfin_write_PORTFIO_EDGE(val)
-#define FIO_EDGE PORTFIO_EDGE
-#define bfin_read_FIO_BOTH() bfin_read_PORTFIO_BOTH()
-#define bfin_write_FIO_BOTH(val) bfin_write_PORTFIO_BOTH(val)
-#define FIO_BOTH PORTFIO_BOTH
-#define bfin_read_FIO_INEN() bfin_read_PORTFIO_INEN()
-#define bfin_write_FIO_INEN(val) bfin_write_PORTFIO_INEN(val)
-#define FIO_INEN PORTFIO_INEN
-#endif
-
-/* FIO USE PORT G*/
-#ifdef CONFIG_BF537_PORT_G
-#define bfin_read_PORT_FER() bfin_read_PORTG_FER()
-#define bfin_write_PORT_FER(val) bfin_write_PORTG_FER(val)
-#define bfin_read_FIO_FLAG_D() bfin_read_PORTGIO()
-#define bfin_write_FIO_FLAG_D(val) bfin_write_PORTGIO(val)
-#define bfin_read_FIO_FLAG_C() bfin_read_PORTGIO_CLEAR()
-#define bfin_write_FIO_FLAG_C(val) bfin_write_PORTGIO_CLEAR(val)
-#define bfin_read_FIO_FLAG_S() bfin_read_PORTGIO_SET()
-#define bfin_write_FIO_FLAG_S(val) bfin_write_PORTGIO_SET(val)
-#define bfin_read_FIO_FLAG_T() bfin_read_PORTGIO_TOGGLE()
-#define bfin_write_FIO_FLAG_T(val) bfin_write_PORTGIO_TOGGLE(val)
-#define bfin_read_FIO_MASKA_D() bfin_read_PORTGIO_MASKA()
-#define bfin_write_FIO_MASKA_D(val) bfin_write_PORTGIO_MASKA(val)
-#define bfin_read_FIO_MASKA_C() bfin_read_PORTGIO_MASKA_CLEAR()
-#define bfin_write_FIO_MASKA_C(val) bfin_write_PORTGIO_MASKA_CLEAR(val)
-#define bfin_read_FIO_MASKA_S() bfin_read_PORTGIO_MASKA_SET()
-#define bfin_write_FIO_MASKA_S(val) bfin_write_PORTGIO_MASKA_SET(val)
-#define bfin_read_FIO_MASKA_T() bfin_read_PORTGIO_MASKA_TOGGLE()
-#define bfin_write_FIO_MASKA_T(val) bfin_write_PORTGIO_MASKA_TOGGLE(val)
-#define bfin_read_FIO_MASKB_D() bfin_read_PORTGIO_MASKB()
-#define bfin_write_FIO_MASKB_D(val) bfin_write_PORTGIO_MASKB(val)
-#define bfin_read_FIO_MASKB_C() bfin_read_PORTGIO_MASKB_CLEAR()
-#define bfin_write_FIO_MASKB_C(val) bfin_write_PORTGIO_MASKB_CLEAR(val)
-#define bfin_read_FIO_MASKB_S() bfin_read_PORTGIO_MASKB_SET()
-#define bfin_write_FIO_MASKB_S(val) bfin_write_PORTGIO_MASKB_SET(val)
-#define bfin_read_FIO_MASKB_T() bfin_read_PORTGIO_MASKB_TOGGLE()
-#define bfin_write_FIO_MASKB_T(val) bfin_write_PORTGIO_MASKB_TOGGLE(val)
-#define bfin_read_FIO_DIR() bfin_read_PORTGIO_DIR()
-#define bfin_write_FIO_DIR(val) bfin_write_PORTGIO_DIR(val)
-#define bfin_read_FIO_POLAR() bfin_read_PORTGIO_POLAR()
-#define bfin_write_FIO_POLAR(val) bfin_write_PORTGIO_POLAR(val)
-#define bfin_read_FIO_EDGE() bfin_read_PORTGIO_EDGE()
-#define bfin_write_FIO_EDGE(val) bfin_write_PORTGIO_EDGE(val)
-#define bfin_read_FIO_BOTH() bfin_read_PORTGIO_BOTH()
-#define bfin_write_FIO_BOTH(val) bfin_write_PORTGIO_BOTH(val)
-#define bfin_read_FIO_INEN() bfin_read_PORTGIO_INEN()
-#define bfin_write_FIO_INEN(val) bfin_write_PORTGIO_INEN(val)
-
-#define bfin_read_FIO_FLAG_D() bfin_read_PORTGIO()
-#define bfin_write_FIO_FLAG_D(val) bfin_write_PORTGIO(val)
-#define FIO_FLAG_D PORTGIO
-#define bfin_read_FIO_FLAG_C() bfin_read_PORTGIO_CLEAR()
-#define bfin_write_FIO_FLAG_C(val) bfin_write_PORTGIO_CLEAR(val)
-#define FIO_FLAG_C PORTGIO_CLEAR
-#define bfin_read_FIO_FLAG_S() bfin_read_PORTGIO_SET()
-#define bfin_write_FIO_FLAG_S(val) bfin_write_PORTGIO_SET(val)
-#define FIO_FLAG_S PORTGIO_SET
-#define bfin_read_FIO_FLAG_T() bfin_read_PORTGIO_TOGGLE()
-#define bfin_write_FIO_FLAG_T(val) bfin_write_PORTGIO_TOGGLE(val)
-#define FIO_FLAG_T PORTGIO_TOGGLE
-#define bfin_read_FIO_MASKA_D() bfin_read_PORTGIO_MASKA()
-#define bfin_write_FIO_MASKA_D(val) bfin_write_PORTGIO_MASKA(val)
-#define FIO_MASKA_D PORTGIO_MASKA
-#define bfin_read_FIO_MASKA_C() bfin_read_PORTGIO_MASKA_CLEAR()
-#define bfin_write_FIO_MASKA_C(val) bfin_write_PORTGIO_MASKA_CLEAR(val)
-#define FIO_MASKA_C PORTGIO_MASKA_CLEAR
-#define bfin_read_FIO_MASKA_S() bfin_read_PORTGIO_MASKA_SET()
-#define bfin_write_FIO_MASKA_S(val) bfin_write_PORTGIO_MASKA_SET(val)
-#define FIO_MASKA_S PORTGIO_MASKA_SET
-#define bfin_read_FIO_MASKA_T() bfin_read_PORTGIO_MASKA_TOGGLE()
-#define bfin_write_FIO_MASKA_T(val) bfin_write_PORTGIO_MASKA_TOGGLE(val)
-#define FIO_MASKA_T PORTGIO_MASKA_TOGGLE
-#define bfin_read_FIO_MASKB_D() bfin_read_PORTGIO_MASKB()
-#define bfin_write_FIO_MASKB_D(val) bfin_write_PORTGIO_MASKB(val)
-#define FIO_MASKB_D PORTGIO_MASKB
-#define bfin_read_FIO_MASKB_C() bfin_read_PORTGIO_MASKB_CLEAR()
-#define bfin_write_FIO_MASKB_C(val) bfin_write_PORTGIO_MASKB_CLEAR(val)
-#define FIO_MASKB_C PORTGIO_MASKB_CLEAR
-#define bfin_read_FIO_MASKB_S() bfin_read_PORTGIO_MASKB_SET()
-#define bfin_write_FIO_MASKB_S(val) bfin_write_PORTGIO_MASKB_SET(val)
-#define FIO_MASKB_S PORTGIO_MASKB_SET
-#define bfin_read_FIO_MASKB_T() bfin_read_PORTGIO_MASKB_TOGGLE()
-#define bfin_write_FIO_MASKB_T(val) bfin_write_PORTGIO_MASKB_TOGGLE(val)
-#define FIO_MASKB_T PORTGIO_MASKB_TOGGLE
-#define bfin_read_FIO_DIR() bfin_read_PORTGIO_DIR()
-#define bfin_write_FIO_DIR(val) bfin_write_PORTGIO_DIR(val)
-#define FIO_DIR PORTGIO_DIR
-#define bfin_read_FIO_POLAR() bfin_read_PORTGIO_POLAR()
-#define bfin_write_FIO_POLAR(val) bfin_write_PORTGIO_POLAR(val)
-#define FIO_POLAR PORTGIO_POLAR
-#define bfin_read_FIO_EDGE() bfin_read_PORTGIO_EDGE()
-#define bfin_write_FIO_EDGE(val) bfin_write_PORTGIO_EDGE(val)
-#define FIO_EDGE PORTGIO_EDGE
-#define bfin_read_FIO_BOTH() bfin_read_PORTGIO_BOTH()
-#define bfin_write_FIO_BOTH(val) bfin_write_PORTGIO_BOTH(val)
-#define FIO_BOTH PORTGIO_BOTH
-#define bfin_read_FIO_INEN() bfin_read_PORTGIO_INEN()
-#define bfin_write_FIO_INEN(val) bfin_write_PORTGIO_INEN(val)
-#define FIO_INEN PORTGIO_INEN
-
-#endif
-
-/* FIO USE PORT H*/
-#ifdef CONFIG_BF537_PORT_H
-#define bfin_read_PORT_FER() bfin_read_PORTH_FER()
-#define bfin_write_PORT_FER(val) bfin_write_PORTH_FER(val)
-#define bfin_read_FIO_FLAG_D() bfin_read_PORTHIO()
-#define bfin_write_FIO_FLAG_D(val) bfin_write_PORTHIO(val)
-#define bfin_read_FIO_FLAG_C() bfin_read_PORTHIO_CLEAR()
-#define bfin_write_FIO_FLAG_C(val) bfin_write_PORTHIO_CLEAR(val)
-#define bfin_read_FIO_FLAG_S() bfin_read_PORTHIO_SET()
-#define bfin_write_FIO_FLAG_S(val) bfin_write_PORTHIO_SET(val)
-#define bfin_read_FIO_FLAG_T() bfin_read_PORTHIO_TOGGLE()
-#define bfin_write_FIO_FLAG_T(val) bfin_write_PORTHIO_TOGGLE(val)
-#define bfin_read_FIO_MASKA_D() bfin_read_PORTHIO_MASKA()
-#define bfin_write_FIO_MASKA_D(val) bfin_write_PORTHIO_MASKA(val)
-#define bfin_read_FIO_MASKA_C() bfin_read_PORTHIO_MASKA_CLEAR()
-#define bfin_write_FIO_MASKA_C(val) bfin_write_PORTHIO_MASKA_CLEAR(val)
-#define bfin_read_FIO_MASKA_S() bfin_read_PORTHIO_MASKA_SET()
-#define bfin_write_FIO_MASKA_S(val) bfin_write_PORTHIO_MASKA_SET(val)
-#define bfin_read_FIO_MASKA_T() bfin_read_PORTHIO_MASKA_TOGGLE()
-#define bfin_write_FIO_MASKA_T(val) bfin_write_PORTHIO_MASKA_TOGGLE(val)
-#define bfin_read_FIO_MASKB_D() bfin_read_PORTHIO_MASKB()
-#define bfin_write_FIO_MASKB_D(val) bfin_write_PORTHIO_MASKB(val)
-#define bfin_read_FIO_MASKB_C() bfin_read_PORTHIO_MASKB_CLEAR()
-#define bfin_write_FIO_MASKB_C(val) bfin_write_PORTHIO_MASKB_CLEAR(val)
-#define bfin_read_FIO_MASKB_S() bfin_read_PORTHIO_MASKB_SET()
-#define bfin_write_FIO_MASKB_S(val) bfin_write_PORTHIO_MASKB_SET(val)
-#define bfin_read_FIO_MASKB_T() bfin_read_PORTHIO_MASKB_TOGGLE()
-#define bfin_write_FIO_MASKB_T(val) bfin_write_PORTHIO_MASKB_TOGGLE(val)
-#define bfin_read_FIO_DIR() bfin_read_PORTHIO_DIR()
-#define bfin_write_FIO_DIR(val) bfin_write_PORTHIO_DIR(val)
-#define bfin_read_FIO_POLAR() bfin_read_PORTHIO_POLAR()
-#define bfin_write_FIO_POLAR(val) bfin_write_PORTHIO_POLAR(val)
-#define bfin_read_FIO_EDGE() bfin_read_PORTHIO_EDGE()
-#define bfin_write_FIO_EDGE(val) bfin_write_PORTHIO_EDGE(val)
-#define bfin_read_FIO_BOTH() bfin_read_PORTHIO_BOTH()
-#define bfin_write_FIO_BOTH(val) bfin_write_PORTHIO_BOTH(val)
-#define bfin_read_FIO_INEN() bfin_read_PORTHIO_INEN()
-#define bfin_write_FIO_INEN(val) bfin_write_PORTHIO_INEN(val)
-
-#define bfin_read_FIO_FLAG_D() bfin_read_PORTHIO()
-#define bfin_write_FIO_FLAG_D(val) bfin_write_PORTHIO(val)
-#define FIO_FLAG_D PORTHIO
-#define bfin_read_FIO_FLAG_C() bfin_read_PORTHIO_CLEAR()
-#define bfin_write_FIO_FLAG_C(val) bfin_write_PORTHIO_CLEAR(val)
-#define FIO_FLAG_C PORTHIO_CLEAR
-#define bfin_read_FIO_FLAG_S() bfin_read_PORTHIO_SET()
-#define bfin_write_FIO_FLAG_S(val) bfin_write_PORTHIO_SET(val)
-#define FIO_FLAG_S PORTHIO_SET
-#define bfin_read_FIO_FLAG_T() bfin_read_PORTHIO_TOGGLE()
-#define bfin_write_FIO_FLAG_T(val) bfin_write_PORTHIO_TOGGLE(val)
-#define FIO_FLAG_T PORTHIO_TOGGLE
-#define bfin_read_FIO_MASKA_D() bfin_read_PORTHIO_MASKA()
-#define bfin_write_FIO_MASKA_D(val) bfin_write_PORTHIO_MASKA(val)
-#define FIO_MASKA_D PORTHIO_MASKA
-#define bfin_read_FIO_MASKA_C() bfin_read_PORTHIO_MASKA_CLEAR()
-#define bfin_write_FIO_MASKA_C(val) bfin_write_PORTHIO_MASKA_CLEAR(val)
-#define FIO_MASKA_C PORTHIO_MASKA_CLEAR
-#define bfin_read_FIO_MASKA_S() bfin_read_PORTHIO_MASKA_SET()
-#define bfin_write_FIO_MASKA_S(val) bfin_write_PORTHIO_MASKA_SET(val)
-#define FIO_MASKA_S PORTHIO_MASKA_SET
-#define bfin_read_FIO_MASKA_T() bfin_read_PORTHIO_MASKA_TOGGLE()
-#define bfin_write_FIO_MASKA_T(val) bfin_write_PORTHIO_MASKA_TOGGLE(val)
-#define FIO_MASKA_T PORTHIO_MASKA_TOGGLE
-#define bfin_read_FIO_MASKB_D() bfin_read_PORTHIO_MASKB()
-#define bfin_write_FIO_MASKB_D(val) bfin_write_PORTHIO_MASKB(val)
-#define FIO_MASKB_D PORTHIO_MASKB
-#define bfin_read_FIO_MASKB_C() bfin_read_PORTHIO_MASKB_CLEAR()
-#define bfin_write_FIO_MASKB_C(val) bfin_write_PORTHIO_MASKB_CLEAR(val)
-#define FIO_MASKB_C PORTHIO_MASKB_CLEAR
-#define bfin_read_FIO_MASKB_S() bfin_read_PORTHIO_MASKB_SET()
-#define bfin_write_FIO_MASKB_S(val) bfin_write_PORTHIO_MASKB_SET(val)
-#define FIO_MASKB_S PORTHIO_MASKB_SET
-#define bfin_read_FIO_MASKB_T() bfin_read_PORTHIO_MASKB_TOGGLE()
-#define bfin_write_FIO_MASKB_T(val) bfin_write_PORTHIO_MASKB_TOGGLE(val)
-#define FIO_MASKB_T PORTHIO_MASKB_TOGGLE
-#define bfin_read_FIO_DIR() bfin_read_PORTHIO_DIR()
-#define bfin_write_FIO_DIR(val) bfin_write_PORTHIO_DIR(val)
-#define FIO_DIR PORTHIO_DIR
-#define bfin_read_FIO_POLAR() bfin_read_PORTHIO_POLAR()
-#define bfin_write_FIO_POLAR(val) bfin_write_PORTHIO_POLAR(val)
-#define FIO_POLAR PORTHIO_POLAR
-#define bfin_read_FIO_EDGE() bfin_read_PORTHIO_EDGE()
-#define bfin_write_FIO_EDGE(val) bfin_write_PORTHIO_EDGE(val)
-#define FIO_EDGE PORTHIO_EDGE
-#define bfin_read_FIO_BOTH() bfin_read_PORTHIO_BOTH()
-#define bfin_write_FIO_BOTH(val) bfin_write_PORTHIO_BOTH(val)
-#define FIO_BOTH PORTHIO_BOTH
-#define bfin_read_FIO_INEN() bfin_read_PORTHIO_INEN()
-#define bfin_write_FIO_INEN(val) bfin_write_PORTHIO_INEN(val)
-#define FIO_INEN PORTHIO_INEN
-
-#endif
-
/* PLL_DIV Masks */
#define CCLK_DIV1 CSEL_DIV1 /* CCLK = VCO / 1 */
#define CCLK_DIV2 CSEL_DIV2 /* CCLK = VCO / 2 */
#ifndef _CDEF_BF534_H
#define _CDEF_BF534_H
+#include <asm/blackfin.h>
+
/* Include all Core registers and bit definitions */
#include "defBF534.h"
bfin_write32(SIC_IWR, IWR_ENABLE(0));
bfin_write16(VR_CTL, val);
- __builtin_bfin_ssync();
+ SSYNC();
local_irq_save(flags);
asm("IDLE;");
#define UART0_GCTL 0xFFC00424 /* Global Control Register */
/* SPI Controller (0xFFC00500 - 0xFFC005FF) */
+#define SPI0_REGBASE 0xFFC00500
#define SPI_CTL 0xFFC00500 /* SPI Control Register */
#define SPI_FLG 0xFFC00504 /* SPI Flag register */
#define SPI_STAT 0xFFC00508 /* SPI Status register */
#define PPI_FRAME 0xFFC01010 /* PPI Frame Length Register */
/* Two-Wire Interface (0xFFC01400 - 0xFFC014FF) */
+#define TWI0_REGBASE 0xFFC01400
#define TWI_CLKDIV 0xFFC01400 /* Serial Clock Divider Register */
#define TWI_CONTROL 0xFFC01404 /* TWI Control Register */
#define TWI_SLAVE_CTL 0xFFC01408 /* Slave Mode Control Register */
#define GM 0x0008 /* Get More (When RDBR Full, Overwrite/Discard*) */
#define PSSE 0x0010 /* Slave-Select Input Enable */
#define EMISO 0x0020 /* Enable MISO As Output */
-#define SPI_SIZE 0x0100 /* Size of Words (16/8* Bits) */
+#define SIZE 0x0100 /* Size of Words (16/8* Bits) */
#define LSBF 0x0200 /* LSB First */
#define CPHA 0x0400 /* Clock Phase */
#define CPOL 0x0800 /* Clock Polarity */
#define IRQ_PH14 96
#define IRQ_PH15 97
+#define GPIO_IRQ_BASE IRQ_PF0
+
#ifdef CONFIG_IRQCHIP_DEMUX_GPIO
#define NR_IRQS (IRQ_PH15+1)
#else
/* Memory Map for ADSP-BF537 processors */
-#ifdef CONFIG_BLKFIN_CACHE
-#define BLKFIN_ICACHESIZE (16*1024)
+#ifdef CONFIG_BFIN_ICACHE
+#define BFIN_ICACHESIZE (16*1024)
#else
-#define BLKFIN_ICACHESIZE (0*1024)
+#define BFIN_ICACHESIZE (0*1024)
#endif
#define L1_CODE_LENGTH 0xC000
-#ifdef CONFIG_BLKFIN_DCACHE
+#ifdef CONFIG_BFIN_DCACHE
-#ifdef CONFIG_BLKFIN_DCACHE_BANKA
+#ifdef CONFIG_BFIN_DCACHE_BANKA
#define DMEM_CNTR (ACACHE_BSRAM | ENDCPLB | PORT_PREF0)
#define L1_DATA_A_LENGTH (0x8000 - 0x4000)
#define L1_DATA_B_LENGTH 0x8000
-#define BLKFIN_DCACHESIZE (16*1024)
-#define BLKFIN_DSUPBANKS 1
+#define BFIN_DCACHESIZE (16*1024)
+#define BFIN_DSUPBANKS 1
#else
#define DMEM_CNTR (ACACHE_BCACHE | ENDCPLB | PORT_PREF0)
#define L1_DATA_A_LENGTH (0x8000 - 0x4000)
#define L1_DATA_B_LENGTH (0x8000 - 0x4000)
-#define BLKFIN_DCACHESIZE (32*1024)
-#define BLKFIN_DSUPBANKS 2
+#define BFIN_DCACHESIZE (32*1024)
+#define BFIN_DSUPBANKS 2
#endif
#else
#define DMEM_CNTR (ASRAM_BSRAM | ENDCPLB | PORT_PREF0)
#define L1_DATA_A_LENGTH 0x8000
#define L1_DATA_B_LENGTH 0x8000
-#define BLKFIN_DCACHESIZE (0*1024)
-#define BLKFIN_DSUPBANKS 0
-#endif /*CONFIG_BLKFIN_DCACHE*/
+#define BFIN_DCACHESIZE (0*1024)
+#define BFIN_DSUPBANKS 0
+#endif /*CONFIG_BFIN_DCACHE*/
#endif /*CONFIG_BF537*/
#define L1_CODE_LENGTH 0xC000
-#ifdef CONFIG_BLKFIN_DCACHE
+#ifdef CONFIG_BFIN_DCACHE
-#ifdef CONFIG_BLKFIN_DCACHE_BANKA
+#ifdef CONFIG_BFIN_DCACHE_BANKA
#define DMEM_CNTR (ACACHE_BSRAM | ENDCPLB | PORT_PREF0)
#define L1_DATA_A_LENGTH (0x4000 - 0x4000)
#define L1_DATA_B_LENGTH 0x4000
-#define BLKFIN_DCACHESIZE (16*1024)
-#define BLKFIN_DSUPBANKS 1
+#define BFIN_DCACHESIZE (16*1024)
+#define BFIN_DSUPBANKS 1
#else
#define DMEM_CNTR (ACACHE_BCACHE | ENDCPLB | PORT_PREF0)
#define L1_DATA_A_LENGTH (0x4000 - 0x4000)
#define L1_DATA_B_LENGTH (0x4000 - 0x4000)
-#define BLKFIN_DCACHESIZE (32*1024)
-#define BLKFIN_DSUPBANKS 2
+#define BFIN_DCACHESIZE (32*1024)
+#define BFIN_DSUPBANKS 2
#endif
#else
#define DMEM_CNTR (ASRAM_BSRAM | ENDCPLB | PORT_PREF0)
#define L1_DATA_A_LENGTH 0x4000
#define L1_DATA_B_LENGTH 0x4000
-#define BLKFIN_DCACHESIZE (0*1024)
-#define BLKFIN_DSUPBANKS 0
-#endif /*CONFIG_BLKFIN_DCACHE*/
+#define BFIN_DCACHESIZE (0*1024)
+#define BFIN_DSUPBANKS 0
+#endif /*CONFIG_BFIN_DCACHE*/
#endif
#define L1_CODE_LENGTH 0xC000
-#ifdef CONFIG_BLKFIN_DCACHE
+#ifdef CONFIG_BFIN_DCACHE
-#ifdef CONFIG_BLKFIN_DCACHE_BANKA
+#ifdef CONFIG_BFIN_DCACHE_BANKA
#define DMEM_CNTR (ACACHE_BSRAM | ENDCPLB | PORT_PREF0)
#define L1_DATA_A_LENGTH (0x8000 - 0x4000)
#define L1_DATA_B_LENGTH 0x8000
-#define BLKFIN_DCACHESIZE (16*1024)
-#define BLKFIN_DSUPBANKS 1
+#define BFIN_DCACHESIZE (16*1024)
+#define BFIN_DSUPBANKS 1
#else
#define DMEM_CNTR (ACACHE_BCACHE | ENDCPLB | PORT_PREF0)
#define L1_DATA_A_LENGTH (0x8000 - 0x4000)
#define L1_DATA_B_LENGTH (0x8000 - 0x4000)
-#define BLKFIN_DCACHESIZE (32*1024)
-#define BLKFIN_DSUPBANKS 2
+#define BFIN_DCACHESIZE (32*1024)
+#define BFIN_DSUPBANKS 2
#endif
#else
#define DMEM_CNTR (ASRAM_BSRAM | ENDCPLB | PORT_PREF0)
#define L1_DATA_A_LENGTH 0x8000
#define L1_DATA_B_LENGTH 0x8000
-#define BLKFIN_DCACHESIZE (0*1024)
-#define BLKFIN_DSUPBANKS 0
-#endif /*CONFIG_BLKFIN_DCACHE*/
+#define BFIN_DCACHESIZE (0*1024)
+#define BFIN_DSUPBANKS 0
+#endif /*CONFIG_BFIN_DCACHE*/
#endif
#define P_SPORT0_DRPRI (P_DEFINED | P_IDENT(PORT_PJ8) | P_FUNCT(0))
#define P_SPORT0_TSCLK (P_DEFINED | P_IDENT(PORT_PJ9) | P_FUNCT(0))
#define P_SPORT0_TFS (P_DEFINED | P_IDENT(PORT_PJ10) | P_FUNCT(0))
-#define P_SPORT0_DTPRI (P_DEFINED | P_IDENT(PORT_PJ11) | P_FUNCT(1))
+#define P_SPORT0_DTPRI (P_DEFINED | P_IDENT(PORT_PJ11) | P_FUNCT(0))
#define P_CAN0_RX (P_DEFINED | P_IDENT(PORT_PJ4) | P_FUNCT(1))
#define P_CAN0_TX (P_DEFINED | P_IDENT(PORT_PJ5) | P_FUNCT(1))
#define P_SPI0_SSEL3 (P_DEFINED | P_IDENT(PORT_PJ10) | P_FUNCT(1))
-
/*
- * File: include/asm-blackfin/mach-bf548/anomaly.h
- * Based on:
- * Author:
- *
- * Created:
- * Description:
- *
- * Rev:
- *
- * Modified:
- *
- *
- * Bugs: Enter bugs at http://blackfin.uclinux.org/
+ * File: include/asm-blackfin/mach-bf548/anomaly.h
+ * Bugs: Enter bugs at http://blackfin.uclinux.org/
*
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2, or (at your option)
- * any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; see the file COPYING.
- * If not, write to the Free Software Foundation,
- * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ * Copyright (C) 2004-2007 Analog Devices Inc.
+ * Licensed under the GPL-2 or later.
+ */
+
+/* This file shoule be up to date with:
+ * - Revision C, July 16, 2007; ADSP-BF549 Silicon Anomaly List
*/
#ifndef _MACH_ANOMALY_H_
#define _MACH_ANOMALY_H_
-#define ANOMALY_05000074 /* A multi issue instruction with dsp32shiftimm in
- slot1 and store of a P register in slot 2 is not
- supported */
-#define ANOMALY_05000119 /* DMA_RUN bit is not valid after a Peripheral Receive
- Channel DMA stops */
-#define ANOMALY_05000122 /* Rx.H can not be used to access 16-bit System MMR
- registers. */
-#define ANOMALY_05000245 /* Spurious Hardware Error from an Access in the
- Shadow of a Conditional Branch */
-#define ANOMALY_05000255 /* Entering Hibernate Mode with RTC Seconds event
- interrupt not functional */
-#define ANOMALY_05000265 /* Sensitivity to noise with slow input edge rates on
- SPORT external receive and transmit clocks. */
-#define ANOMALY_05000272 /* Certain data cache write through modes fail for
- VDDint <=0.9V */
-#define ANOMALY_05000281 /* False Hardware Error Exception when ISR context is
- not restored */
-#define ANOMALY_05000310 /* False Hardware Errors Caused by Fetches at the
- Boundary of Reserved Memory */
-#define ANOMALY_05000312 /* Errors When SSYNC, CSYNC, or Loads to LT, LB and
- LC Registers Are Interrupted */
-#define ANOMALY_05000324 /* TWI Slave Boot Mode Is Not Functional */
-#define ANOMALY_05000325 /* External FIFO Boot Mode Is Not Functional */
-#define ANOMALY_05000327 /* Data Lost When Core and DMA Accesses Are Made to
- the USB FIFO Simultaneously */
-#define ANOMALY_05000328 /* Incorrect Access of OTP_STATUS During otp_write()
- function */
-#define ANOMALY_05000329 /* Synchronous Burst Flash Boot Mode Is Not Functional
- */
-#define ANOMALY_05000330 /* Host DMA Boot Mode Is Not Functional */
-#define ANOMALY_05000334 /* Inadequate Timing Margins on DDR DQS to DQ and DQM
- Skew */
-#define ANOMALY_05000335 /* Inadequate Rotary Debounce Logic Duration */
-#define ANOMALY_05000336 /* Phantom Interrupt Occurs After First Configuration
- of Host DMA Port */
-#define ANOMALY_05000337 /* Disallowed Configuration Prevents Subsequent
- Allowed Configuration on Host DMA Port */
-#define ANOMALY_05000338 /* Slave-Mode SPI0 MISO Failure With CPHA = 0 */
-#endif /* _MACH_ANOMALY_H_ */
+/* Multi-Issue Instruction with dsp32shiftimm in slot1 and P-reg Store in slot 2 Not Supported */
+#define ANOMALY_05000074 (1)
+/* DMA_RUN Bit Is Not Valid after a Peripheral Receive Channel DMA Stops */
+#define ANOMALY_05000119 (1)
+/* Rx.H Cannot Be Used to Access 16-bit System MMR Registers */
+#define ANOMALY_05000122 (1)
+/* Spurious Hardware Error from an Access in the Shadow of a Conditional Branch */
+#define ANOMALY_05000245 (1)
+/* Sensitivity To Noise with Slow Input Edge Rates on External SPORT TX and RX Clocks */
+#define ANOMALY_05000265 (1)
+/* Certain Data Cache Writethrough Modes Fail for Vddint <= 0.9V */
+#define ANOMALY_05000272 (1)
+/* False Hardware Error Exception when ISR context is not restored */
+#define ANOMALY_05000281 (1)
+/* SSYNCs After Writes To CAN/DMA MMR Registers Are Not Always Handled Correctly */
+#define ANOMALY_05000304 (1)
+/* False Hardware Errors Caused by Fetches at the Boundary of Reserved Memory */
+#define ANOMALY_05000310 (1)
+/* Errors When SSYNC, CSYNC, or Loads to LT, LB and LC Registers Are Interrupted */
+#define ANOMALY_05000312 (1)
+/* TWI Slave Boot Mode Is Not Functional */
+#define ANOMALY_05000324 (1)
+/* External FIFO Boot Mode Is Not Functional */
+#define ANOMALY_05000325 (1)
+/* Data Lost When Core and DMA Accesses Are Made to the USB FIFO Simultaneously */
+#define ANOMALY_05000327 (1)
+/* Incorrect Access of OTP_STATUS During otp_write() Function */
+#define ANOMALY_05000328 (1)
+/* Synchronous Burst Flash Boot Mode Is Not Functional */
+#define ANOMALY_05000329 (1)
+/* Host DMA Boot Mode Is Not Functional */
+#define ANOMALY_05000330 (1)
+/* Inadequate Timing Margins on DDR DQS to DQ and DQM Skew */
+#define ANOMALY_05000334 (1)
+/* Inadequate Rotary Debounce Logic Duration */
+#define ANOMALY_05000335 (1)
+/* Phantom Interrupt Occurs After First Configuration of Host DMA Port */
+#define ANOMALY_05000336 (1)
+/* Disallowed Configuration Prevents Subsequent Allowed Configuration on Host DMA Port */
+#define ANOMALY_05000337 (1)
+/* Slave-Mode SPI0 MISO Failure With CPHA = 0 */
+#define ANOMALY_05000338 (1)
+/* If Memory Reads Are Enabled on SDH or HOSTDP, Other DMAC1 Peripherals Cannot Read */
+#define ANOMALY_05000340 (1)
+/* Boot Host Wait (HWAIT) and Boot Host Wait Alternate (HWAITA) Signals Are Swapped */
+#define ANOMALY_05000344 (1)
+/* USB Calibration Value Is Not Intialized */
+#define ANOMALY_05000346 (1)
+/* Boot ROM Kernel Incorrectly Alters Reset Value of USB Register */
+#define ANOMALY_05000347 (1)
+/* Data Lost when Core Reads SDH Data FIFO */
+#define ANOMALY_05000349 (1)
+/* PLL Status Register Is Inaccurate */
+#define ANOMALY_05000351 (1)
+
+/* Anomalies that don't exist on this proc */
+#define ANOMALY_05000125 (0)
+#define ANOMALY_05000158 (0)
+#define ANOMALY_05000183 (0)
+#define ANOMALY_05000198 (0)
+#define ANOMALY_05000230 (0)
+#define ANOMALY_05000244 (0)
+#define ANOMALY_05000261 (0)
+#define ANOMALY_05000263 (0)
+#define ANOMALY_05000266 (0)
+#define ANOMALY_05000273 (0)
+#define ANOMALY_05000311 (0)
+#define ANOMALY_05000323 (0)
+
+#endif
/***************************/
-#define BLKFIN_DSUBBANKS 4
-#define BLKFIN_DWAYS 2
-#define BLKFIN_DLINES 64
-#define BLKFIN_ISUBBANKS 4
-#define BLKFIN_IWAYS 4
-#define BLKFIN_ILINES 32
+#define BFIN_DSUBBANKS 4
+#define BFIN_DWAYS 2
+#define BFIN_DLINES 64
+#define BFIN_ISUBBANKS 4
+#define BFIN_IWAYS 4
+#define BFIN_ILINES 32
#define WAY0_L 0x1
#define WAY1_L 0x2
#define AMGCTLVAL (V_AMBEN | V_AMCKEN)
-#define MAX_VC 650000000
-#define MIN_VC 50000000
-
-/********************************PLL Settings **************************************/
-#ifdef CONFIG_BFIN_KERNEL_CLOCK
-#if (CONFIG_VCO_MULT < 0)
-#error "VCO Multiplier is less than 0. Please select a different value"
-#endif
-
-#if (CONFIG_VCO_MULT == 0)
-#error "VCO Multiplier should be greater than 0. Please select a different value"
-#endif
-
-#if (CONFIG_VCO_MULT > 64)
-#error "VCO Multiplier is more than 64. Please select a different value"
-#endif
-
-#ifndef CONFIG_CLKIN_HALF
-#define CONFIG_VCO_HZ (CONFIG_CLKIN_HZ * CONFIG_VCO_MULT)
-#else
-#define CONFIG_VCO_HZ ((CONFIG_CLKIN_HZ * CONFIG_VCO_MULT)/2)
-#endif
-
-#ifndef CONFIG_PLL_BYPASS
-#define CONFIG_CCLK_HZ (CONFIG_VCO_HZ/CONFIG_CCLK_DIV)
-#define CONFIG_SCLK_HZ (CONFIG_VCO_HZ/CONFIG_SCLK_DIV)
-#else
-#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ
-#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ
-#endif
-
-#if (CONFIG_SCLK_DIV < 1)
-#error "SCLK DIV cannot be less than 1 or more than 15. Please select a proper value"
-#endif
-
-#if (CONFIG_SCLK_DIV > 15)
-#error "SCLK DIV cannot be less than 1 or more than 15. Please select a proper value"
-#endif
-
-#if (CONFIG_CCLK_DIV != 1)
-#if (CONFIG_CCLK_DIV != 2)
-#if (CONFIG_CCLK_DIV != 4)
-#if (CONFIG_CCLK_DIV != 8)
-#error "CCLK DIV can be 1,2,4 or 8 only. Please select a proper value"
-#endif
-#endif
-#endif
-#endif
-
-#if (CONFIG_VCO_HZ > MAX_VC)
-#error "VCO selected is more than maximum value. Please change the VCO multipler"
-#endif
-
-#if (CONFIG_SCLK_HZ > 133000000)
-#error "Sclk value selected is more than maximum. Please select a proper value for SCLK multiplier"
-#endif
-
-#if (CONFIG_SCLK_HZ < 27000000)
-#error "Sclk value selected is less than minimum. Please select a proper value for SCLK multiplier"
-#endif
-
-#if (CONFIG_SCLK_HZ >= CONFIG_CCLK_HZ)
-#if (CONFIG_SCLK_HZ != CONFIG_CLKIN_HZ)
-#if (CONFIG_CCLK_HZ != CONFIG_CLKIN_HZ)
-#error "Please select sclk less than cclk"
-#endif
-#endif
-#endif
-
-#if (CONFIG_CCLK_DIV == 1)
-#define CONFIG_CCLK_ACT_DIV CCLK_DIV1
-#endif
-#if (CONFIG_CCLK_DIV == 2)
-#define CONFIG_CCLK_ACT_DIV CCLK_DIV2
-#endif
-#if (CONFIG_CCLK_DIV == 4)
-#define CONFIG_CCLK_ACT_DIV CCLK_DIV4
-#endif
-#if (CONFIG_CCLK_DIV == 8)
-#define CONFIG_CCLK_ACT_DIV CCLK_DIV8
-#endif
-#ifndef CONFIG_CCLK_ACT_DIV
-#define CONFIG_CCLK_ACT_DIV CONFIG_CCLK_DIV_not_defined_properly
-#endif
-
-#endif /* CONFIG_BFIN_KERNEL_CLOCK */
-
#ifdef CONFIG_BF542
#define CPU "BF542"
#define CPUID 0x027c8000
#define CPUID 0x0
#endif
-#if (CONFIG_MEM_SIZE % 4)
-#error "SDRAM mem size must be multible of 4MB"
-#endif
-
-#define SDRAM_IGENERIC (CPLB_L1_CHBL | CPLB_USER_RD | CPLB_VALID | CPLB_PORTPRIO)
-#define SDRAM_IKERNEL (SDRAM_IGENERIC | CPLB_LOCK)
-#define L1_IMEMORY ( CPLB_USER_RD | CPLB_VALID | CPLB_LOCK)
-#define SDRAM_INON_CHBL ( CPLB_USER_RD | CPLB_VALID)
-
-/*Use the menuconfig cache policy here - CONFIG_BLKFIN_WT/CONFIG_BLKFIN_WB*/
-
-#define ANOMALY_05000158_WORKAROUND 0x200
-#ifdef CONFIG_BLKFIN_WB /*Write Back Policy */
-#define SDRAM_DGENERIC (CPLB_L1_CHBL | CPLB_DIRTY \
- | CPLB_SUPV_WR | CPLB_USER_WR | CPLB_USER_RD | CPLB_VALID | ANOMALY_05000158_WORKAROUND)
-#else /*Write Through */
-#define SDRAM_DGENERIC (CPLB_L1_CHBL | CPLB_WT | CPLB_L1_AOW \
- | CPLB_SUPV_WR | CPLB_USER_WR | CPLB_USER_RD | CPLB_VALID | ANOMALY_05000158_WORKAROUND | CPLB_DIRTY )
-#endif
-
-
-#define L1_DMEMORY (CPLB_SUPV_WR | CPLB_USER_WR | CPLB_USER_RD | CPLB_VALID | ANOMALY_05000158_WORKAROUND | CPLB_LOCK | CPLB_DIRTY )
-#define SDRAM_DNON_CHBL (CPLB_SUPV_WR | CPLB_USER_WR | CPLB_USER_RD | CPLB_VALID | ANOMALY_05000158_WORKAROUND | CPLB_DIRTY )
-#define SDRAM_EBIU (CPLB_SUPV_WR | CPLB_USER_WR | CPLB_USER_RD | CPLB_VALID | ANOMALY_05000158_WORKAROUND | CPLB_DIRTY )
-#define SDRAM_OOPS (CPLB_VALID | ANOMALY_05000158_WORKAROUND | CPLB_LOCK | CPLB_DIRTY )
-
-#define SIZE_1K 0x00000400 /* 1K */
-#define SIZE_4K 0x00001000 /* 4K */
-#define SIZE_1M 0x00100000 /* 1M */
-#define SIZE_4M 0x00400000 /* 4M */
-
-#define MAX_CPLBS (16 * 2)
-
-/*
-* Number of required data CPLB switchtable entries
-* MEMSIZE / 4 (we mostly install 4M page size CPLBs
-* approx 16 for smaller 1MB page size CPLBs for allignment purposes
-* 1 for L1 Data Memory
-* 1 for CONFIG_DEBUG_HUNT_FOR_ZERO
-* 1 for ASYNC Memory
-*/
-
-
-#define MAX_SWITCH_D_CPLBS (((CONFIG_MEM_SIZE / 4) + 16 + 1 + 1 + 1) * 2)
-
-/*
-* Number of required instruction CPLB switchtable entries
-* MEMSIZE / 4 (we mostly install 4M page size CPLBs
-* approx 12 for smaller 1MB page size CPLBs for allignment purposes
-* 1 for L1 Instruction Memory
-* 1 for CONFIG_DEBUG_HUNT_FOR_ZERO
-*/
-
-#define MAX_SWITCH_I_CPLBS (((CONFIG_MEM_SIZE / 4) + 12 + 1 + 1) * 2)
-
#endif /* __MACH_BF48_H__ */
#include <linux/serial.h>
#include <asm/dma.h>
+#include <asm/portmux.h>
#define NR_PORTS 4
int nr_ports = ARRAY_SIZE(bfin_serial_resource);
+#define DRIVER_NAME "bfin-uart"
+
static void bfin_serial_hw_init(struct bfin_serial_port *uart)
{
#ifdef CONFIG_SERIAL_BFIN_UART0
- /* Enable UART0 RX and TX on pin 7 & 8 of PORT E */
- bfin_write_PORTE_FER(0x180 | bfin_read_PORTE_FER());
- bfin_write_PORTE_MUX(0x3C000 | bfin_read_PORTE_MUX());
+ peripheral_request(P_UART0_TX, DRIVER_NAME);
+ peripheral_request(P_UART0_RX, DRIVER_NAME);
#endif
#ifdef CONFIG_SERIAL_BFIN_UART1
- /* Enable UART1 RX and TX on pin 0 & 1 of PORT H */
- bfin_write_PORTH_FER(0x3 | bfin_read_PORTH_FER());
- bfin_write_PORTH_MUX(~0xF & bfin_read_PORTH_MUX());
+ peripheral_request(P_UART1_TX, DRIVER_NAME);
+ peripheral_request(P_UART1_RX, DRIVER_NAME);
+
#ifdef CONFIG_BFIN_UART1_CTSRTS
- /* Enable UART1 RTS and CTS on pin 9 & 10 of PORT E */
- bfin_write_PORTE_FER(0x600 | bfin_read_PORTE_FER());
- bfin_write_PORTE_MUX(~0x3C0000 & bfin_read_PORTE_MUX());
+ peripheral_request(P_UART1_RTS, DRIVER_NAME);
+ peripheral_request(P_UART1_CTS DRIVER_NAME);
#endif
#endif
#ifdef CONFIG_SERIAL_BFIN_UART2
- /* Enable UART2 RX and TX on pin 4 & 5 of PORT B */
- bfin_write_PORTB_FER(0x30 | bfin_read_PORTB_FER());
- bfin_write_PORTB_MUX(~0xF00 & bfin_read_PORTB_MUX());
+ peripheral_request(P_UART2_TX, DRIVER_NAME);
+ peripheral_request(P_UART2_RX, DRIVER_NAME);
#endif
#ifdef CONFIG_SERIAL_BFIN_UART3
- /* Enable UART3 RX and TX on pin 6 & 7 of PORT B */
- bfin_write_PORTB_FER(0xC0 | bfin_read_PORTB_FER());
- bfin_write_PORTB_MUX(~0xF000 | bfin_read_PORTB_MUX());
+ peripheral_request(P_UART3_TX, DRIVER_NAME);
+ peripheral_request(P_UART3_RX, DRIVER_NAME);
+
#ifdef CONFIG_BFIN_UART3_CTSRTS
- /* Enable UART3 RTS and CTS on pin 2 & 3 of PORT B */
- bfin_write_PORTB_FER(0xC | bfin_read_PORTB_FER());
- bfin_write_PORTB_MUX(~0xF0 | bfin_read_PORTB_MUX());
+ peripheral_request(P_UART3_RTS, DRIVER_NAME);
+ peripheral_request(P_UART3_CTS DRIVER_NAME);
#endif
#endif
SSYNC();
#ifdef CONFIG_SERIAL_BFIN_CTSRTS
if (uart->cts_pin >= 0) {
- gpio_request(uart->cts_pin, NULL);
+ gpio_request(uart->cts_pin, DRIVER_NAME);
gpio_direction_input(uart->cts_pin);
}
if (uart->rts_pin >= 0) {
- gpio_request(uart->rts_pin, NULL);
+ gpio_request(uart->rts_pin, DRIVER_NAME);
gpio_direction_output(uart->rts_pin);
}
#endif
#include "defBF549.h"
#endif
-#if !(defined(__ASSEMBLY__) || defined(ASSEMBLY))
+#if !defined(__ASSEMBLY__)
#ifdef CONFIG_BF542
#include "cdefBF542.h"
#endif
#ifndef _CDEF_BF54X_H
#define _CDEF_BF54X_H
+#include <asm/blackfin.h>
+
#include "defBF54x_base.h"
#include <asm/system.h>
bfin_write32(SIC_IWR2, 0);
bfin_write16(VR_CTL, val);
- __builtin_bfin_ssync();
+ SSYNC();
local_irq_save(flags);
asm("IDLE;");
/* Two Wire Interface Registers (TWI1) */
+#define TWI1_REGBASE 0xffc02200
#define TWI1_CLKDIV 0xffc02200 /* Clock Divider Register */
#define TWI1_CONTROL 0xffc02204 /* TWI Control Register */
#define TWI1_SLAVE_CTRL 0xffc02208 /* TWI Slave Mode Control Register */
/* Two Wire Interface Registers (TWI1) */
+#define TWI1_REGBASE 0xffc02200
#define TWI1_CLKDIV 0xffc02200 /* Clock Divider Register */
#define TWI1_CONTROL 0xffc02204 /* TWI Control Register */
#define TWI1_SLAVE_CTRL 0xffc02208 /* TWI Slave Mode Control Register */
/* SPI2 Registers */
+#define SPI2_REGBASE 0xffc02400
#define SPI2_CTL 0xffc02400 /* SPI2 Control Register */
#define SPI2_FLG 0xffc02404 /* SPI2 Flag Register */
#define SPI2_STAT 0xffc02408 /* SPI2 Status Register */
/* Two Wire Interface Registers (TWI1) */
+#define TWI1_REGBASE 0xffc02200
#define TWI1_CLKDIV 0xffc02200 /* Clock Divider Register */
#define TWI1_CONTROL 0xffc02204 /* TWI Control Register */
#define TWI1_SLAVE_CTRL 0xffc02208 /* TWI Slave Mode Control Register */
/* SPI2 Registers */
+#define SPI2_REGBASE 0xffc02400
#define SPI2_CTL 0xffc02400 /* SPI2 Control Register */
#define SPI2_FLG 0xffc02404 /* SPI2 Flag Register */
#define SPI2_STAT 0xffc02408 /* SPI2 Status Register */
/* SPI0 Registers */
+#define SPI0_REGBASE 0xffc00500
#define SPI0_CTL 0xffc00500 /* SPI0 Control Register */
#define SPI0_FLG 0xffc00504 /* SPI0 Flag Register */
#define SPI0_STAT 0xffc00508 /* SPI0 Status Register */
/* Two Wire Interface Registers (TWI0) */
+#define TWI0_REGBASE 0xffc00700
#define TWI0_CLKDIV 0xffc00700 /* Clock Divider Register */
#define TWI0_CONTROL 0xffc00704 /* TWI Control Register */
#define TWI0_SLAVE_CTRL 0xffc00708 /* TWI Slave Mode Control Register */
/* SPI1 Registers */
+#define SPI1_REGBASE 0xffc02300
#define SPI1_CTL 0xffc02300 /* SPI1 Control Register */
#define SPI1_FLG 0xffc02304 /* SPI1 Flag Register */
#define SPI1_STAT 0xffc02308 /* SPI1 Status Register */
unsigned short dummy7;
unsigned int port_mux;
};
-
-int gpio_request(unsigned short gpio, const char *label);
-void peripheral_free(unsigned short per);
-int peripheral_request_list(unsigned short per[], const char *label);
-void peripheral_free_list(unsigned short per[]);
/* The ABSTRACT IRQ definitions */
/** the first seven of the following are fixed, the rest you change if you need to **/
-#define IRQ_EMU 0 /* Emulation */
-#define IRQ_RST 1 /* reset */
-#define IRQ_NMI 2 /* Non Maskable */
-#define IRQ_EVX 3 /* Exception */
-#define IRQ_UNUSED 4 /* - unused interrupt*/
-#define IRQ_HWERR 5 /* Hardware Error */
-#define IRQ_CORETMR 6 /* Core timer */
-
-#define BFIN_IRQ(x) ((x) + 7)
-
-#define IRQ_PLL_WAKEUP BFIN_IRQ(0) /* PLL Wakeup Interrupt */
-#define IRQ_DMAC0_ERR BFIN_IRQ(1) /* DMAC0 Status Interrupt */
-#define IRQ_EPPI0_ERR BFIN_IRQ(2) /* EPPI0 Error Interrupt */
-#define IRQ_SPORT0_ERR BFIN_IRQ(3) /* SPORT0 Error Interrupt */
-#define IRQ_SPORT1_ERR BFIN_IRQ(4) /* SPORT1 Error Interrupt */
-#define IRQ_SPI0_ERR BFIN_IRQ(5) /* SPI0 Status(Error) Interrupt */
-#define IRQ_UART0_ERR BFIN_IRQ(6) /* UART0 Status(Error) Interrupt */
-#define IRQ_RTC BFIN_IRQ(7) /* RTC Interrupt */
-#define IRQ_EPPI0 BFIN_IRQ(8) /* EPPI0 Interrupt (DMA12) */
-#define IRQ_SPORT0_RX BFIN_IRQ(9) /* SPORT0 RX Interrupt (DMA0) */
-#define IRQ_SPORT0_TX BFIN_IRQ(10) /* SPORT0 TX Interrupt (DMA1) */
-#define IRQ_SPORT1_RX BFIN_IRQ(11) /* SPORT1 RX Interrupt (DMA2) */
-#define IRQ_SPORT1_TX BFIN_IRQ(12) /* SPORT1 TX Interrupt (DMA3) */
-#define IRQ_SPI0 BFIN_IRQ(13) /* SPI0 Interrupt (DMA4) */
-#define IRQ_UART0_RX BFIN_IRQ(14) /* UART0 RX Interrupt (DMA6) */
-#define IRQ_UART0_TX BFIN_IRQ(15) /* UART0 TX Interrupt (DMA7) */
-#define IRQ_TIMER8 BFIN_IRQ(16) /* TIMER 8 Interrupt */
-#define IRQ_TIMER9 BFIN_IRQ(17) /* TIMER 9 Interrupt */
-#define IRQ_TIMER10 BFIN_IRQ(18) /* TIMER 10 Interrupt */
-#define IRQ_PINT0 BFIN_IRQ(19) /* PINT0 Interrupt */
-#define IRQ_PINT1 BFIN_IRQ(20) /* PINT1 Interrupt */
-#define IRQ_MDMAS0 BFIN_IRQ(21) /* MDMA Stream 0 Interrupt */
-#define IRQ_MDMAS1 BFIN_IRQ(22) /* MDMA Stream 1 Interrupt */
-#define IRQ_WATCHDOG BFIN_IRQ(23) /* Watchdog Interrupt */
-#define IRQ_DMAC1_ERR BFIN_IRQ(24) /* DMAC1 Status (Error) Interrupt */
-#define IRQ_SPORT2_ERR BFIN_IRQ(25) /* SPORT2 Error Interrupt */
-#define IRQ_SPORT3_ERR BFIN_IRQ(26) /* SPORT3 Error Interrupt */
-#define IRQ_MXVR_DATA BFIN_IRQ(27) /* MXVR Data Interrupt */
-#define IRQ_SPI1_ERR BFIN_IRQ(28) /* SPI1 Status (Error) Interrupt */
-#define IRQ_SPI2_ERR BFIN_IRQ(29) /* SPI2 Status (Error) Interrupt */
-#define IRQ_UART1_ERR BFIN_IRQ(30) /* UART1 Status (Error) Interrupt */
-#define IRQ_UART2_ERR BFIN_IRQ(31) /* UART2 Status (Error) Interrupt */
-#define IRQ_CAN0_ERR BFIN_IRQ(32) /* CAN0 Status (Error) Interrupt */
-#define IRQ_SPORT2_RX BFIN_IRQ(33) /* SPORT2 RX (DMA18) Interrupt */
-#define IRQ_SPORT2_TX BFIN_IRQ(34) /* SPORT2 TX (DMA19) Interrupt */
-#define IRQ_SPORT3_RX BFIN_IRQ(35) /* SPORT3 RX (DMA20) Interrupt */
-#define IRQ_SPORT3_TX BFIN_IRQ(36) /* SPORT3 TX (DMA21) Interrupt */
-#define IRQ_EPPI1 BFIN_IRQ(37) /* EPP1 (DMA13) Interrupt */
-#define IRQ_EPPI2 BFIN_IRQ(38) /* EPP2 (DMA14) Interrupt */
-#define IRQ_SPI1 BFIN_IRQ(39) /* SPI1 (DMA5) Interrupt */
-#define IRQ_SPI2 BFIN_IRQ(40) /* SPI2 (DMA23) Interrupt */
-#define IRQ_UART1_RX BFIN_IRQ(41) /* UART1 RX (DMA8) Interrupt */
-#define IRQ_UART1_TX BFIN_IRQ(42) /* UART1 TX (DMA9) Interrupt */
-#define IRQ_ATAPI_RX BFIN_IRQ(43) /* ATAPI RX (DMA10) Interrupt */
-#define IRQ_ATAPI_TX BFIN_IRQ(44) /* ATAPI TX (DMA11) Interrupt */
-#define IRQ_TWI0 BFIN_IRQ(45) /* TWI0 Interrupt */
-#define IRQ_TWI1 BFIN_IRQ(46) /* TWI1 Interrupt */
-#define IRQ_TWI IRQ_TWI0 /* TWI Interrupt */
-#define IRQ_CAN0_RX BFIN_IRQ(47) /* CAN0 Receive Interrupt */
-#define IRQ_CAN0_TX BFIN_IRQ(48) /* CAN0 Transmit Interrupt */
-#define IRQ_MDMAS2 BFIN_IRQ(49) /* MDMA Stream 2 Interrupt */
-#define IRQ_MDMAS3 BFIN_IRQ(50) /* MDMA Stream 3 Interrupt */
-#define IRQ_MXVR_ERR BFIN_IRQ(51) /* MXVR Status (Error) Interrupt */
-#define IRQ_MXVR_MSG BFIN_IRQ(52) /* MXVR Message Interrupt */
-#define IRQ_MXVR_PKT BFIN_IRQ(53) /* MXVR Packet Interrupt */
-#define IRQ_EPP1_ERR BFIN_IRQ(54) /* EPPI1 Error Interrupt */
-#define IRQ_EPP2_ERR BFIN_IRQ(55) /* EPPI2 Error Interrupt */
-#define IRQ_UART3_ERR BFIN_IRQ(56) /* UART3 Status (Error) Interrupt */
-#define IRQ_HOST_ERR BFIN_IRQ(57) /* HOST Status (Error) Interrupt */
-#define IRQ_PIXC_ERR BFIN_IRQ(59) /* PIXC Status (Error) Interrupt */
-#define IRQ_NFC_ERR BFIN_IRQ(60) /* NFC Error Interrupt */
-#define IRQ_ATAPI_ERR BFIN_IRQ(61) /* ATAPI Error Interrupt */
-#define IRQ_CAN1_ERR BFIN_IRQ(62) /* CAN1 Status (Error) Interrupt */
-#define IRQ_HS_DMA_ERR BFIN_IRQ(63) /* Handshake DMA Status Interrupt */
-#define IRQ_PIXC_IN0 BFIN_IRQ(64) /* PIXC IN0 (DMA15) Interrupt */
-#define IRQ_PIXC_IN1 BFIN_IRQ(65) /* PIXC IN1 (DMA16) Interrupt */
-#define IRQ_PIXC_OUT BFIN_IRQ(66) /* PIXC OUT (DMA17) Interrupt */
-#define IRQ_SDH BFIN_IRQ(67) /* SDH/NFC (DMA22) Interrupt */
-#define IRQ_CNT BFIN_IRQ(68) /* CNT Interrupt */
-#define IRQ_KEY BFIN_IRQ(69) /* KEY Interrupt */
-#define IRQ_CAN1_RX BFIN_IRQ(70) /* CAN1 RX Interrupt */
-#define IRQ_CAN1_TX BFIN_IRQ(71) /* CAN1 TX Interrupt */
-#define IRQ_SDH_MASK0 BFIN_IRQ(72) /* SDH Mask 0 Interrupt */
-#define IRQ_SDH_MASK1 BFIN_IRQ(73) /* SDH Mask 1 Interrupt */
-#define IRQ_USB_INT0 BFIN_IRQ(75) /* USB INT0 Interrupt */
-#define IRQ_USB_INT1 BFIN_IRQ(76) /* USB INT1 Interrupt */
-#define IRQ_USB_INT2 BFIN_IRQ(77) /* USB INT2 Interrupt */
-#define IRQ_USB_DMA BFIN_IRQ(78) /* USB DMA Interrupt */
-#define IRQ_OPTSEC BFIN_IRQ(79) /* OTPSEC Interrupt */
-#define IRQ_TIMER0 BFIN_IRQ(86) /* Timer 0 Interrupt */
-#define IRQ_TIMER1 BFIN_IRQ(87) /* Timer 1 Interrupt */
-#define IRQ_TIMER2 BFIN_IRQ(88) /* Timer 2 Interrupt */
-#define IRQ_TIMER3 BFIN_IRQ(89) /* Timer 3 Interrupt */
-#define IRQ_TIMER4 BFIN_IRQ(90) /* Timer 4 Interrupt */
-#define IRQ_TIMER5 BFIN_IRQ(91) /* Timer 5 Interrupt */
-#define IRQ_TIMER6 BFIN_IRQ(92) /* Timer 6 Interrupt */
-#define IRQ_TIMER7 BFIN_IRQ(93) /* Timer 7 Interrupt */
-#define IRQ_PINT2 BFIN_IRQ(94) /* PINT2 Interrupt */
-#define IRQ_PINT3 BFIN_IRQ(95) /* PINT3 Interrupt */
-
-#define SYS_IRQS IRQ_PINT3
-
-#define BFIN_PA_IRQ(x) ((x) + SYS_IRQS + 1)
-#define IRQ_PA0 BFIN_PA_IRQ(0)
-#define IRQ_PA1 BFIN_PA_IRQ(1)
-#define IRQ_PA2 BFIN_PA_IRQ(2)
-#define IRQ_PA3 BFIN_PA_IRQ(3)
-#define IRQ_PA4 BFIN_PA_IRQ(4)
-#define IRQ_PA5 BFIN_PA_IRQ(5)
-#define IRQ_PA6 BFIN_PA_IRQ(6)
-#define IRQ_PA7 BFIN_PA_IRQ(7)
-#define IRQ_PA8 BFIN_PA_IRQ(8)
-#define IRQ_PA9 BFIN_PA_IRQ(9)
-#define IRQ_PA10 BFIN_PA_IRQ(10)
-#define IRQ_PA11 BFIN_PA_IRQ(11)
-#define IRQ_PA12 BFIN_PA_IRQ(12)
-#define IRQ_PA13 BFIN_PA_IRQ(13)
-#define IRQ_PA14 BFIN_PA_IRQ(14)
-#define IRQ_PA15 BFIN_PA_IRQ(15)
-
-#define BFIN_PB_IRQ(x) ((x) + IRQ_PA15 + 1)
-#define IRQ_PB0 BFIN_PB_IRQ(0)
-#define IRQ_PB1 BFIN_PB_IRQ(1)
-#define IRQ_PB2 BFIN_PB_IRQ(2)
-#define IRQ_PB3 BFIN_PB_IRQ(3)
-#define IRQ_PB4 BFIN_PB_IRQ(4)
-#define IRQ_PB5 BFIN_PB_IRQ(5)
-#define IRQ_PB6 BFIN_PB_IRQ(6)
-#define IRQ_PB7 BFIN_PB_IRQ(7)
-#define IRQ_PB8 BFIN_PB_IRQ(8)
-#define IRQ_PB9 BFIN_PB_IRQ(9)
-#define IRQ_PB10 BFIN_PB_IRQ(10)
-#define IRQ_PB11 BFIN_PB_IRQ(11)
-#define IRQ_PB12 BFIN_PB_IRQ(12)
-#define IRQ_PB13 BFIN_PB_IRQ(13)
-#define IRQ_PB14 BFIN_PB_IRQ(14)
-#define IRQ_PB15 BFIN_PB_IRQ(15) /* N/A */
-
-#define BFIN_PC_IRQ(x) ((x) + IRQ_PB15 + 1)
-#define IRQ_PC0 BFIN_PC_IRQ(0)
-#define IRQ_PC1 BFIN_PC_IRQ(1)
-#define IRQ_PC2 BFIN_PC_IRQ(2)
-#define IRQ_PC3 BFIN_PC_IRQ(3)
-#define IRQ_PC4 BFIN_PC_IRQ(4)
-#define IRQ_PC5 BFIN_PC_IRQ(5)
-#define IRQ_PC6 BFIN_PC_IRQ(6)
-#define IRQ_PC7 BFIN_PC_IRQ(7)
-#define IRQ_PC8 BFIN_PC_IRQ(8)
-#define IRQ_PC9 BFIN_PC_IRQ(9)
-#define IRQ_PC10 BFIN_PC_IRQ(10)
-#define IRQ_PC11 BFIN_PC_IRQ(11)
-#define IRQ_PC12 BFIN_PC_IRQ(12)
-#define IRQ_PC13 BFIN_PC_IRQ(13)
-#define IRQ_PC14 BFIN_PC_IRQ(14) /* N/A */
-#define IRQ_PC15 BFIN_PC_IRQ(15) /* N/A */
-
-#define BFIN_PD_IRQ(x) ((x) + IRQ_PC15 + 1)
-#define IRQ_PD0 BFIN_PD_IRQ(0)
-#define IRQ_PD1 BFIN_PD_IRQ(1)
-#define IRQ_PD2 BFIN_PD_IRQ(2)
-#define IRQ_PD3 BFIN_PD_IRQ(3)
-#define IRQ_PD4 BFIN_PD_IRQ(4)
-#define IRQ_PD5 BFIN_PD_IRQ(5)
-#define IRQ_PD6 BFIN_PD_IRQ(6)
-#define IRQ_PD7 BFIN_PD_IRQ(7)
-#define IRQ_PD8 BFIN_PD_IRQ(8)
-#define IRQ_PD9 BFIN_PD_IRQ(9)
-#define IRQ_PD10 BFIN_PD_IRQ(10)
-#define IRQ_PD11 BFIN_PD_IRQ(11)
-#define IRQ_PD12 BFIN_PD_IRQ(12)
-#define IRQ_PD13 BFIN_PD_IRQ(13)
-#define IRQ_PD14 BFIN_PD_IRQ(14)
-#define IRQ_PD15 BFIN_PD_IRQ(15)
-
-#define BFIN_PE_IRQ(x) ((x) + IRQ_PD15 + 1)
-#define IRQ_PE0 BFIN_PE_IRQ(0)
-#define IRQ_PE1 BFIN_PE_IRQ(1)
-#define IRQ_PE2 BFIN_PE_IRQ(2)
-#define IRQ_PE3 BFIN_PE_IRQ(3)
-#define IRQ_PE4 BFIN_PE_IRQ(4)
-#define IRQ_PE5 BFIN_PE_IRQ(5)
-#define IRQ_PE6 BFIN_PE_IRQ(6)
-#define IRQ_PE7 BFIN_PE_IRQ(7)
-#define IRQ_PE8 BFIN_PE_IRQ(8)
-#define IRQ_PE9 BFIN_PE_IRQ(9)
-#define IRQ_PE10 BFIN_PE_IRQ(10)
-#define IRQ_PE11 BFIN_PE_IRQ(11)
-#define IRQ_PE12 BFIN_PE_IRQ(12)
-#define IRQ_PE13 BFIN_PE_IRQ(13)
-#define IRQ_PE14 BFIN_PE_IRQ(14)
-#define IRQ_PE15 BFIN_PE_IRQ(15)
-
-#define BFIN_PF_IRQ(x) ((x) + IRQ_PE15 + 1)
-#define IRQ_PF0 BFIN_PF_IRQ(0)
-#define IRQ_PF1 BFIN_PF_IRQ(1)
-#define IRQ_PF2 BFIN_PF_IRQ(2)
-#define IRQ_PF3 BFIN_PF_IRQ(3)
-#define IRQ_PF4 BFIN_PF_IRQ(4)
-#define IRQ_PF5 BFIN_PF_IRQ(5)
-#define IRQ_PF6 BFIN_PF_IRQ(6)
-#define IRQ_PF7 BFIN_PF_IRQ(7)
-#define IRQ_PF8 BFIN_PF_IRQ(8)
-#define IRQ_PF9 BFIN_PF_IRQ(9)
-#define IRQ_PF10 BFIN_PF_IRQ(10)
-#define IRQ_PF11 BFIN_PF_IRQ(11)
-#define IRQ_PF12 BFIN_PF_IRQ(12)
-#define IRQ_PF13 BFIN_PF_IRQ(13)
-#define IRQ_PF14 BFIN_PF_IRQ(14)
-#define IRQ_PF15 BFIN_PF_IRQ(15)
-
-#define BFIN_PG_IRQ(x) ((x) + IRQ_PF15 + 1)
-#define IRQ_PG0 BFIN_PG_IRQ(0)
-#define IRQ_PG1 BFIN_PG_IRQ(1)
-#define IRQ_PG2 BFIN_PG_IRQ(2)
-#define IRQ_PG3 BFIN_PG_IRQ(3)
-#define IRQ_PG4 BFIN_PG_IRQ(4)
-#define IRQ_PG5 BFIN_PG_IRQ(5)
-#define IRQ_PG6 BFIN_PG_IRQ(6)
-#define IRQ_PG7 BFIN_PG_IRQ(7)
-#define IRQ_PG8 BFIN_PG_IRQ(8)
-#define IRQ_PG9 BFIN_PG_IRQ(9)
-#define IRQ_PG10 BFIN_PG_IRQ(10)
-#define IRQ_PG11 BFIN_PG_IRQ(11)
-#define IRQ_PG12 BFIN_PG_IRQ(12)
-#define IRQ_PG13 BFIN_PG_IRQ(13)
-#define IRQ_PG14 BFIN_PG_IRQ(14)
-#define IRQ_PG15 BFIN_PG_IRQ(15)
-
-#define BFIN_PH_IRQ(x) ((x) + IRQ_PG15 + 1)
-#define IRQ_PH0 BFIN_PH_IRQ(0)
-#define IRQ_PH1 BFIN_PH_IRQ(1)
-#define IRQ_PH2 BFIN_PH_IRQ(2)
-#define IRQ_PH3 BFIN_PH_IRQ(3)
-#define IRQ_PH4 BFIN_PH_IRQ(4)
-#define IRQ_PH5 BFIN_PH_IRQ(5)
-#define IRQ_PH6 BFIN_PH_IRQ(6)
-#define IRQ_PH7 BFIN_PH_IRQ(7)
-#define IRQ_PH8 BFIN_PH_IRQ(8)
-#define IRQ_PH9 BFIN_PH_IRQ(9)
-#define IRQ_PH10 BFIN_PH_IRQ(10)
-#define IRQ_PH11 BFIN_PH_IRQ(11)
-#define IRQ_PH12 BFIN_PH_IRQ(12)
-#define IRQ_PH13 BFIN_PH_IRQ(13)
-#define IRQ_PH14 BFIN_PH_IRQ(14) /* N/A */
-#define IRQ_PH15 BFIN_PH_IRQ(15) /* N/A */
-
-#define BFIN_PI_IRQ(x) ((x) + IRQ_PH15 + 1)
-#define IRQ_PI0 BFIN_PI_IRQ(0)
-#define IRQ_PI1 BFIN_PI_IRQ(1)
-#define IRQ_PI2 BFIN_PI_IRQ(2)
-#define IRQ_PI3 BFIN_PI_IRQ(3)
-#define IRQ_PI4 BFIN_PI_IRQ(4)
-#define IRQ_PI5 BFIN_PI_IRQ(5)
-#define IRQ_PI6 BFIN_PI_IRQ(6)
-#define IRQ_PI7 BFIN_PI_IRQ(7)
-#define IRQ_PI8 BFIN_PI_IRQ(8)
-#define IRQ_PI9 BFIN_PI_IRQ(9)
-#define IRQ_PI10 BFIN_PI_IRQ(10)
-#define IRQ_PI11 BFIN_PI_IRQ(11)
-#define IRQ_PI12 BFIN_PI_IRQ(12)
-#define IRQ_PI13 BFIN_PI_IRQ(13)
-#define IRQ_PI14 BFIN_PI_IRQ(14)
-#define IRQ_PI15 BFIN_PI_IRQ(15)
-
-#define BFIN_PJ_IRQ(x) ((x) + IRQ_PI15 + 1)
-#define IRQ_PJ0 BFIN_PJ_IRQ(0)
-#define IRQ_PJ1 BFIN_PJ_IRQ(1)
-#define IRQ_PJ2 BFIN_PJ_IRQ(2)
-#define IRQ_PJ3 BFIN_PJ_IRQ(3)
-#define IRQ_PJ4 BFIN_PJ_IRQ(4)
-#define IRQ_PJ5 BFIN_PJ_IRQ(5)
-#define IRQ_PJ6 BFIN_PJ_IRQ(6)
-#define IRQ_PJ7 BFIN_PJ_IRQ(7)
-#define IRQ_PJ8 BFIN_PJ_IRQ(8)
-#define IRQ_PJ9 BFIN_PJ_IRQ(9)
-#define IRQ_PJ10 BFIN_PJ_IRQ(10)
-#define IRQ_PJ11 BFIN_PJ_IRQ(11)
-#define IRQ_PJ12 BFIN_PJ_IRQ(12)
-#define IRQ_PJ13 BFIN_PJ_IRQ(13)
-#define IRQ_PJ14 BFIN_PJ_IRQ(14) /* N/A */
-#define IRQ_PJ15 BFIN_PJ_IRQ(15) /* N/A */
+#define IRQ_EMU 0 /* Emulation */
+#define IRQ_RST 1 /* reset */
+#define IRQ_NMI 2 /* Non Maskable */
+#define IRQ_EVX 3 /* Exception */
+#define IRQ_UNUSED 4 /* - unused interrupt*/
+#define IRQ_HWERR 5 /* Hardware Error */
+#define IRQ_CORETMR 6 /* Core timer */
+
+#define BFIN_IRQ(x) ((x) + 7)
+
+#define IRQ_PLL_WAKEUP BFIN_IRQ(0) /* PLL Wakeup Interrupt */
+#define IRQ_DMAC0_ERROR BFIN_IRQ(1) /* DMAC0 Status Interrupt */
+#define IRQ_EPPI0_ERROR BFIN_IRQ(2) /* EPPI0 Error Interrupt */
+#define IRQ_SPORT0_ERROR BFIN_IRQ(3) /* SPORT0 Error Interrupt */
+#define IRQ_SPORT1_ERROR BFIN_IRQ(4) /* SPORT1 Error Interrupt */
+#define IRQ_SPI0_ERROR BFIN_IRQ(5) /* SPI0 Status(Error) Interrupt */
+#define IRQ_UART0_ERROR BFIN_IRQ(6) /* UART0 Status(Error) Interrupt */
+#define IRQ_RTC BFIN_IRQ(7) /* RTC Interrupt */
+#define IRQ_EPPI0 BFIN_IRQ(8) /* EPPI0 Interrupt (DMA12) */
+#define IRQ_SPORT0_RX BFIN_IRQ(9) /* SPORT0 RX Interrupt (DMA0) */
+#define IRQ_SPORT0_TX BFIN_IRQ(10) /* SPORT0 TX Interrupt (DMA1) */
+#define IRQ_SPORT1_RX BFIN_IRQ(11) /* SPORT1 RX Interrupt (DMA2) */
+#define IRQ_SPORT1_TX BFIN_IRQ(12) /* SPORT1 TX Interrupt (DMA3) */
+#define IRQ_SPI0 BFIN_IRQ(13) /* SPI0 Interrupt (DMA4) */
+#define IRQ_UART0_RX BFIN_IRQ(14) /* UART0 RX Interrupt (DMA6) */
+#define IRQ_UART0_TX BFIN_IRQ(15) /* UART0 TX Interrupt (DMA7) */
+#define IRQ_TIMER8 BFIN_IRQ(16) /* TIMER 8 Interrupt */
+#define IRQ_TIMER9 BFIN_IRQ(17) /* TIMER 9 Interrupt */
+#define IRQ_TIMER10 BFIN_IRQ(18) /* TIMER 10 Interrupt */
+#define IRQ_PINT0 BFIN_IRQ(19) /* PINT0 Interrupt */
+#define IRQ_PINT1 BFIN_IRQ(20) /* PINT1 Interrupt */
+#define IRQ_MDMAS0 BFIN_IRQ(21) /* MDMA Stream 0 Interrupt */
+#define IRQ_MDMAS1 BFIN_IRQ(22) /* MDMA Stream 1 Interrupt */
+#define IRQ_WATCHDOG BFIN_IRQ(23) /* Watchdog Interrupt */
+#define IRQ_DMAC1_ERROR BFIN_IRQ(24) /* DMAC1 Status (Error) Interrupt */
+#define IRQ_SPORT2_ERROR BFIN_IRQ(25) /* SPORT2 Error Interrupt */
+#define IRQ_SPORT3_ERROR BFIN_IRQ(26) /* SPORT3 Error Interrupt */
+#define IRQ_MXVR_DATA BFIN_IRQ(27) /* MXVR Data Interrupt */
+#define IRQ_SPI1_ERROR BFIN_IRQ(28) /* SPI1 Status (Error) Interrupt */
+#define IRQ_SPI2_ERROR BFIN_IRQ(29) /* SPI2 Status (Error) Interrupt */
+#define IRQ_UART1_ERROR BFIN_IRQ(30) /* UART1 Status (Error) Interrupt */
+#define IRQ_UART2_ERROR BFIN_IRQ(31) /* UART2 Status (Error) Interrupt */
+#define IRQ_CAN0_ERROR BFIN_IRQ(32) /* CAN0 Status (Error) Interrupt */
+#define IRQ_SPORT2_RX BFIN_IRQ(33) /* SPORT2 RX (DMA18) Interrupt */
+#define IRQ_SPORT2_TX BFIN_IRQ(34) /* SPORT2 TX (DMA19) Interrupt */
+#define IRQ_SPORT3_RX BFIN_IRQ(35) /* SPORT3 RX (DMA20) Interrupt */
+#define IRQ_SPORT3_TX BFIN_IRQ(36) /* SPORT3 TX (DMA21) Interrupt */
+#define IRQ_EPPI1 BFIN_IRQ(37) /* EPP1 (DMA13) Interrupt */
+#define IRQ_EPPI2 BFIN_IRQ(38) /* EPP2 (DMA14) Interrupt */
+#define IRQ_SPI1 BFIN_IRQ(39) /* SPI1 (DMA5) Interrupt */
+#define IRQ_SPI2 BFIN_IRQ(40) /* SPI2 (DMA23) Interrupt */
+#define IRQ_UART1_RX BFIN_IRQ(41) /* UART1 RX (DMA8) Interrupt */
+#define IRQ_UART1_TX BFIN_IRQ(42) /* UART1 TX (DMA9) Interrupt */
+#define IRQ_ATAPI_RX BFIN_IRQ(43) /* ATAPI RX (DMA10) Interrupt */
+#define IRQ_ATAPI_TX BFIN_IRQ(44) /* ATAPI TX (DMA11) Interrupt */
+#define IRQ_TWI0 BFIN_IRQ(45) /* TWI0 Interrupt */
+#define IRQ_TWI1 BFIN_IRQ(46) /* TWI1 Interrupt */
+#define IRQ_CAN0_RX BFIN_IRQ(47) /* CAN0 Receive Interrupt */
+#define IRQ_CAN0_TX BFIN_IRQ(48) /* CAN0 Transmit Interrupt */
+#define IRQ_MDMAS2 BFIN_IRQ(49) /* MDMA Stream 2 Interrupt */
+#define IRQ_MDMAS3 BFIN_IRQ(50) /* MDMA Stream 3 Interrupt */
+#define IRQ_MXVR_ERROR BFIN_IRQ(51) /* MXVR Status (Error) Interrupt */
+#define IRQ_MXVR_MSG BFIN_IRQ(52) /* MXVR Message Interrupt */
+#define IRQ_MXVR_PKT BFIN_IRQ(53) /* MXVR Packet Interrupt */
+#define IRQ_EPP1_ERROR BFIN_IRQ(54) /* EPPI1 Error Interrupt */
+#define IRQ_EPP2_ERROR BFIN_IRQ(55) /* EPPI2 Error Interrupt */
+#define IRQ_UART3_ERROR BFIN_IRQ(56) /* UART3 Status (Error) Interrupt */
+#define IRQ_HOST_ERROR BFIN_IRQ(57) /* HOST Status (Error) Interrupt */
+#define IRQ_PIXC_ERROR BFIN_IRQ(59) /* PIXC Status (Error) Interrupt */
+#define IRQ_NFC_ERROR BFIN_IRQ(60) /* NFC Error Interrupt */
+#define IRQ_ATAPI_ERROR BFIN_IRQ(61) /* ATAPI Error Interrupt */
+#define IRQ_CAN1_ERROR BFIN_IRQ(62) /* CAN1 Status (Error) Interrupt */
+#define IRQ_HS_DMA_ERROR BFIN_IRQ(63) /* Handshake DMA Status Interrupt */
+#define IRQ_PIXC_IN0 BFIN_IRQ(64) /* PIXC IN0 (DMA15) Interrupt */
+#define IRQ_PIXC_IN1 BFIN_IRQ(65) /* PIXC IN1 (DMA16) Interrupt */
+#define IRQ_PIXC_OUT BFIN_IRQ(66) /* PIXC OUT (DMA17) Interrupt */
+#define IRQ_SDH BFIN_IRQ(67) /* SDH/NFC (DMA22) Interrupt */
+#define IRQ_CNT BFIN_IRQ(68) /* CNT Interrupt */
+#define IRQ_KEY BFIN_IRQ(69) /* KEY Interrupt */
+#define IRQ_CAN1_RX BFIN_IRQ(70) /* CAN1 RX Interrupt */
+#define IRQ_CAN1_TX BFIN_IRQ(71) /* CAN1 TX Interrupt */
+#define IRQ_SDH_MASK0 BFIN_IRQ(72) /* SDH Mask 0 Interrupt */
+#define IRQ_SDH_MASK1 BFIN_IRQ(73) /* SDH Mask 1 Interrupt */
+#define IRQ_USB_INT0 BFIN_IRQ(75) /* USB INT0 Interrupt */
+#define IRQ_USB_INT1 BFIN_IRQ(76) /* USB INT1 Interrupt */
+#define IRQ_USB_INT2 BFIN_IRQ(77) /* USB INT2 Interrupt */
+#define IRQ_USB_DMA BFIN_IRQ(78) /* USB DMA Interrupt */
+#define IRQ_OPTSEC BFIN_IRQ(79) /* OTPSEC Interrupt */
+#define IRQ_TIMER0 BFIN_IRQ(86) /* Timer 0 Interrupt */
+#define IRQ_TIMER1 BFIN_IRQ(87) /* Timer 1 Interrupt */
+#define IRQ_TIMER2 BFIN_IRQ(88) /* Timer 2 Interrupt */
+#define IRQ_TIMER3 BFIN_IRQ(89) /* Timer 3 Interrupt */
+#define IRQ_TIMER4 BFIN_IRQ(90) /* Timer 4 Interrupt */
+#define IRQ_TIMER5 BFIN_IRQ(91) /* Timer 5 Interrupt */
+#define IRQ_TIMER6 BFIN_IRQ(92) /* Timer 6 Interrupt */
+#define IRQ_TIMER7 BFIN_IRQ(93) /* Timer 7 Interrupt */
+#define IRQ_PINT2 BFIN_IRQ(94) /* PINT2 Interrupt */
+#define IRQ_PINT3 BFIN_IRQ(95) /* PINT3 Interrupt */
+
+#define SYS_IRQS IRQ_PINT3
+
+#define BFIN_PA_IRQ(x) ((x) + SYS_IRQS + 1)
+#define IRQ_PA0 BFIN_PA_IRQ(0)
+#define IRQ_PA1 BFIN_PA_IRQ(1)
+#define IRQ_PA2 BFIN_PA_IRQ(2)
+#define IRQ_PA3 BFIN_PA_IRQ(3)
+#define IRQ_PA4 BFIN_PA_IRQ(4)
+#define IRQ_PA5 BFIN_PA_IRQ(5)
+#define IRQ_PA6 BFIN_PA_IRQ(6)
+#define IRQ_PA7 BFIN_PA_IRQ(7)
+#define IRQ_PA8 BFIN_PA_IRQ(8)
+#define IRQ_PA9 BFIN_PA_IRQ(9)
+#define IRQ_PA10 BFIN_PA_IRQ(10)
+#define IRQ_PA11 BFIN_PA_IRQ(11)
+#define IRQ_PA12 BFIN_PA_IRQ(12)
+#define IRQ_PA13 BFIN_PA_IRQ(13)
+#define IRQ_PA14 BFIN_PA_IRQ(14)
+#define IRQ_PA15 BFIN_PA_IRQ(15)
+
+#define BFIN_PB_IRQ(x) ((x) + IRQ_PA15 + 1)
+#define IRQ_PB0 BFIN_PB_IRQ(0)
+#define IRQ_PB1 BFIN_PB_IRQ(1)
+#define IRQ_PB2 BFIN_PB_IRQ(2)
+#define IRQ_PB3 BFIN_PB_IRQ(3)
+#define IRQ_PB4 BFIN_PB_IRQ(4)
+#define IRQ_PB5 BFIN_PB_IRQ(5)
+#define IRQ_PB6 BFIN_PB_IRQ(6)
+#define IRQ_PB7 BFIN_PB_IRQ(7)
+#define IRQ_PB8 BFIN_PB_IRQ(8)
+#define IRQ_PB9 BFIN_PB_IRQ(9)
+#define IRQ_PB10 BFIN_PB_IRQ(10)
+#define IRQ_PB11 BFIN_PB_IRQ(11)
+#define IRQ_PB12 BFIN_PB_IRQ(12)
+#define IRQ_PB13 BFIN_PB_IRQ(13)
+#define IRQ_PB14 BFIN_PB_IRQ(14)
+#define IRQ_PB15 BFIN_PB_IRQ(15) /* N/A */
+
+#define BFIN_PC_IRQ(x) ((x) + IRQ_PB15 + 1)
+#define IRQ_PC0 BFIN_PC_IRQ(0)
+#define IRQ_PC1 BFIN_PC_IRQ(1)
+#define IRQ_PC2 BFIN_PC_IRQ(2)
+#define IRQ_PC3 BFIN_PC_IRQ(3)
+#define IRQ_PC4 BFIN_PC_IRQ(4)
+#define IRQ_PC5 BFIN_PC_IRQ(5)
+#define IRQ_PC6 BFIN_PC_IRQ(6)
+#define IRQ_PC7 BFIN_PC_IRQ(7)
+#define IRQ_PC8 BFIN_PC_IRQ(8)
+#define IRQ_PC9 BFIN_PC_IRQ(9)
+#define IRQ_PC10 BFIN_PC_IRQ(10)
+#define IRQ_PC11 BFIN_PC_IRQ(11)
+#define IRQ_PC12 BFIN_PC_IRQ(12)
+#define IRQ_PC13 BFIN_PC_IRQ(13)
+#define IRQ_PC14 BFIN_PC_IRQ(14) /* N/A */
+#define IRQ_PC15 BFIN_PC_IRQ(15) /* N/A */
+
+#define BFIN_PD_IRQ(x) ((x) + IRQ_PC15 + 1)
+#define IRQ_PD0 BFIN_PD_IRQ(0)
+#define IRQ_PD1 BFIN_PD_IRQ(1)
+#define IRQ_PD2 BFIN_PD_IRQ(2)
+#define IRQ_PD3 BFIN_PD_IRQ(3)
+#define IRQ_PD4 BFIN_PD_IRQ(4)
+#define IRQ_PD5 BFIN_PD_IRQ(5)
+#define IRQ_PD6 BFIN_PD_IRQ(6)
+#define IRQ_PD7 BFIN_PD_IRQ(7)
+#define IRQ_PD8 BFIN_PD_IRQ(8)
+#define IRQ_PD9 BFIN_PD_IRQ(9)
+#define IRQ_PD10 BFIN_PD_IRQ(10)
+#define IRQ_PD11 BFIN_PD_IRQ(11)
+#define IRQ_PD12 BFIN_PD_IRQ(12)
+#define IRQ_PD13 BFIN_PD_IRQ(13)
+#define IRQ_PD14 BFIN_PD_IRQ(14)
+#define IRQ_PD15 BFIN_PD_IRQ(15)
+
+#define BFIN_PE_IRQ(x) ((x) + IRQ_PD15 + 1)
+#define IRQ_PE0 BFIN_PE_IRQ(0)
+#define IRQ_PE1 BFIN_PE_IRQ(1)
+#define IRQ_PE2 BFIN_PE_IRQ(2)
+#define IRQ_PE3 BFIN_PE_IRQ(3)
+#define IRQ_PE4 BFIN_PE_IRQ(4)
+#define IRQ_PE5 BFIN_PE_IRQ(5)
+#define IRQ_PE6 BFIN_PE_IRQ(6)
+#define IRQ_PE7 BFIN_PE_IRQ(7)
+#define IRQ_PE8 BFIN_PE_IRQ(8)
+#define IRQ_PE9 BFIN_PE_IRQ(9)
+#define IRQ_PE10 BFIN_PE_IRQ(10)
+#define IRQ_PE11 BFIN_PE_IRQ(11)
+#define IRQ_PE12 BFIN_PE_IRQ(12)
+#define IRQ_PE13 BFIN_PE_IRQ(13)
+#define IRQ_PE14 BFIN_PE_IRQ(14)
+#define IRQ_PE15 BFIN_PE_IRQ(15)
+
+#define BFIN_PF_IRQ(x) ((x) + IRQ_PE15 + 1)
+#define IRQ_PF0 BFIN_PF_IRQ(0)
+#define IRQ_PF1 BFIN_PF_IRQ(1)
+#define IRQ_PF2 BFIN_PF_IRQ(2)
+#define IRQ_PF3 BFIN_PF_IRQ(3)
+#define IRQ_PF4 BFIN_PF_IRQ(4)
+#define IRQ_PF5 BFIN_PF_IRQ(5)
+#define IRQ_PF6 BFIN_PF_IRQ(6)
+#define IRQ_PF7 BFIN_PF_IRQ(7)
+#define IRQ_PF8 BFIN_PF_IRQ(8)
+#define IRQ_PF9 BFIN_PF_IRQ(9)
+#define IRQ_PF10 BFIN_PF_IRQ(10)
+#define IRQ_PF11 BFIN_PF_IRQ(11)
+#define IRQ_PF12 BFIN_PF_IRQ(12)
+#define IRQ_PF13 BFIN_PF_IRQ(13)
+#define IRQ_PF14 BFIN_PF_IRQ(14)
+#define IRQ_PF15 BFIN_PF_IRQ(15)
+
+#define BFIN_PG_IRQ(x) ((x) + IRQ_PF15 + 1)
+#define IRQ_PG0 BFIN_PG_IRQ(0)
+#define IRQ_PG1 BFIN_PG_IRQ(1)
+#define IRQ_PG2 BFIN_PG_IRQ(2)
+#define IRQ_PG3 BFIN_PG_IRQ(3)
+#define IRQ_PG4 BFIN_PG_IRQ(4)
+#define IRQ_PG5 BFIN_PG_IRQ(5)
+#define IRQ_PG6 BFIN_PG_IRQ(6)
+#define IRQ_PG7 BFIN_PG_IRQ(7)
+#define IRQ_PG8 BFIN_PG_IRQ(8)
+#define IRQ_PG9 BFIN_PG_IRQ(9)
+#define IRQ_PG10 BFIN_PG_IRQ(10)
+#define IRQ_PG11 BFIN_PG_IRQ(11)
+#define IRQ_PG12 BFIN_PG_IRQ(12)
+#define IRQ_PG13 BFIN_PG_IRQ(13)
+#define IRQ_PG14 BFIN_PG_IRQ(14)
+#define IRQ_PG15 BFIN_PG_IRQ(15)
+
+#define BFIN_PH_IRQ(x) ((x) + IRQ_PG15 + 1)
+#define IRQ_PH0 BFIN_PH_IRQ(0)
+#define IRQ_PH1 BFIN_PH_IRQ(1)
+#define IRQ_PH2 BFIN_PH_IRQ(2)
+#define IRQ_PH3 BFIN_PH_IRQ(3)
+#define IRQ_PH4 BFIN_PH_IRQ(4)
+#define IRQ_PH5 BFIN_PH_IRQ(5)
+#define IRQ_PH6 BFIN_PH_IRQ(6)
+#define IRQ_PH7 BFIN_PH_IRQ(7)
+#define IRQ_PH8 BFIN_PH_IRQ(8)
+#define IRQ_PH9 BFIN_PH_IRQ(9)
+#define IRQ_PH10 BFIN_PH_IRQ(10)
+#define IRQ_PH11 BFIN_PH_IRQ(11)
+#define IRQ_PH12 BFIN_PH_IRQ(12)
+#define IRQ_PH13 BFIN_PH_IRQ(13)
+#define IRQ_PH14 BFIN_PH_IRQ(14) /* N/A */
+#define IRQ_PH15 BFIN_PH_IRQ(15) /* N/A */
+
+#define BFIN_PI_IRQ(x) ((x) + IRQ_PH15 + 1)
+#define IRQ_PI0 BFIN_PI_IRQ(0)
+#define IRQ_PI1 BFIN_PI_IRQ(1)
+#define IRQ_PI2 BFIN_PI_IRQ(2)
+#define IRQ_PI3 BFIN_PI_IRQ(3)
+#define IRQ_PI4 BFIN_PI_IRQ(4)
+#define IRQ_PI5 BFIN_PI_IRQ(5)
+#define IRQ_PI6 BFIN_PI_IRQ(6)
+#define IRQ_PI7 BFIN_PI_IRQ(7)
+#define IRQ_PI8 BFIN_PI_IRQ(8)
+#define IRQ_PI9 BFIN_PI_IRQ(9)
+#define IRQ_PI10 BFIN_PI_IRQ(10)
+#define IRQ_PI11 BFIN_PI_IRQ(11)
+#define IRQ_PI12 BFIN_PI_IRQ(12)
+#define IRQ_PI13 BFIN_PI_IRQ(13)
+#define IRQ_PI14 BFIN_PI_IRQ(14)
+#define IRQ_PI15 BFIN_PI_IRQ(15)
+
+#define BFIN_PJ_IRQ(x) ((x) + IRQ_PI15 + 1)
+#define IRQ_PJ0 BFIN_PJ_IRQ(0)
+#define IRQ_PJ1 BFIN_PJ_IRQ(1)
+#define IRQ_PJ2 BFIN_PJ_IRQ(2)
+#define IRQ_PJ3 BFIN_PJ_IRQ(3)
+#define IRQ_PJ4 BFIN_PJ_IRQ(4)
+#define IRQ_PJ5 BFIN_PJ_IRQ(5)
+#define IRQ_PJ6 BFIN_PJ_IRQ(6)
+#define IRQ_PJ7 BFIN_PJ_IRQ(7)
+#define IRQ_PJ8 BFIN_PJ_IRQ(8)
+#define IRQ_PJ9 BFIN_PJ_IRQ(9)
+#define IRQ_PJ10 BFIN_PJ_IRQ(10)
+#define IRQ_PJ11 BFIN_PJ_IRQ(11)
+#define IRQ_PJ12 BFIN_PJ_IRQ(12)
+#define IRQ_PJ13 BFIN_PJ_IRQ(13)
+#define IRQ_PJ14 BFIN_PJ_IRQ(14) /* N/A */
+#define IRQ_PJ15 BFIN_PJ_IRQ(15) /* N/A */
+
+#define GPIO_IRQ_BASE IRQ_PA0
#ifdef CONFIG_IRQCHIP_DEMUX_GPIO
#define NR_IRQS (IRQ_PJ15+1)
#define NR_IRQS (SYS_IRQS+1)
#endif
+/* For compatibility reasons with existing code */
+
+#define IRQ_DMAC0_ERR IRQ_DMAC0_ERROR
+#define IRQ_EPPI0_ERR IRQ_EPPI0_ERROR
+#define IRQ_SPORT0_ERR IRQ_SPORT0_ERROR
+#define IRQ_SPORT1_ERR IRQ_SPORT1_ERROR
+#define IRQ_SPI0_ERR IRQ_SPI0_ERROR
+#define IRQ_UART0_ERR IRQ_UART0_ERROR
+#define IRQ_DMAC1_ERR IRQ_DMAC1_ERROR
+#define IRQ_SPORT2_ERR IRQ_SPORT2_ERROR
+#define IRQ_SPORT3_ERR IRQ_SPORT3_ERROR
+#define IRQ_SPI1_ERR IRQ_SPI1_ERROR
+#define IRQ_SPI2_ERR IRQ_SPI2_ERROR
+#define IRQ_UART1_ERR IRQ_UART1_ERROR
+#define IRQ_UART2_ERR IRQ_UART2_ERROR
+#define IRQ_CAN0_ERR IRQ_CAN0_ERROR
+#define IRQ_MXVR_ERR IRQ_MXVR_ERROR
+#define IRQ_EPP1_ERR IRQ_EPP1_ERROR
+#define IRQ_EPP2_ERR IRQ_EPP2_ERROR
+#define IRQ_UART3_ERR IRQ_UART3_ERROR
+#define IRQ_HOST_ERR IRQ_HOST_ERROR
+#define IRQ_PIXC_ERR IRQ_PIXC_ERROR
+#define IRQ_NFC_ERR IRQ_NFC_ERROR
+#define IRQ_ATAPI_ERR IRQ_ATAPI_ERROR
+#define IRQ_CAN1_ERR IRQ_CAN1_ERROR
+#define IRQ_HS_DMA_ERR IRQ_HS_DMA_ERROR
+
+
#define IVG7 7
#define IVG8 8
#define IVG9 9
/* Level 1 Memory */
/* Memory Map for ADSP-BF548 processors */
-#ifdef CONFIG_BLKFIN_ICACHE
-#define BLKFIN_ICACHESIZE (16*1024)
+#ifdef CONFIG_BFIN_ICACHE
+#define BFIN_ICACHESIZE (16*1024)
#else
-#define BLKFIN_ICACHESIZE (0*1024)
+#define BFIN_ICACHESIZE (0*1024)
#endif
#define L1_CODE_START 0xFFA00000
#define L1_CODE_LENGTH 0xC000
-#ifdef CONFIG_BLKFIN_DCACHE
+#ifdef CONFIG_BFIN_DCACHE
-#ifdef CONFIG_BLKFIN_DCACHE_BANKA
+#ifdef CONFIG_BFIN_DCACHE_BANKA
#define DMEM_CNTR (ACACHE_BSRAM | ENDCPLB | PORT_PREF0)
#define L1_DATA_A_LENGTH (0x8000 - 0x4000)
#define L1_DATA_B_LENGTH 0x8000
-#define BLKFIN_DCACHESIZE (16*1024)
-#define BLKFIN_DSUPBANKS 1
+#define BFIN_DCACHESIZE (16*1024)
+#define BFIN_DSUPBANKS 1
#else
#define DMEM_CNTR (ACACHE_BCACHE | ENDCPLB | PORT_PREF0)
#define L1_DATA_A_LENGTH (0x8000 - 0x4000)
#define L1_DATA_B_LENGTH (0x8000 - 0x4000)
-#define BLKFIN_DCACHESIZE (32*1024)
-#define BLKFIN_DSUPBANKS 2
+#define BFIN_DCACHESIZE (32*1024)
+#define BFIN_DSUPBANKS 2
#endif
#else
#define DMEM_CNTR (ASRAM_BSRAM | ENDCPLB | PORT_PREF0)
#define L1_DATA_A_LENGTH 0x8000
#define L1_DATA_B_LENGTH 0x8000
-#define BLKFIN_DCACHESIZE (0*1024)
-#define BLKFIN_DSUPBANKS 0
-#endif /*CONFIG_BLKFIN_DCACHE*/
+#define BFIN_DCACHESIZE (0*1024)
+#define BFIN_DSUPBANKS 0
+#endif /*CONFIG_BFIN_DCACHE*/
/* Scratch Pad Memory */
-
/*
- * File: include/asm-blackfin/mach-bf561/anomaly.h
- * Based on:
- * Author:
- *
- * Created:
- * Description:
- *
- * Rev:
- *
- * Modified:
- *
- * Bugs: Enter bugs at http://blackfin.uclinux.org/
+ * File: include/asm-blackfin/mach-bf561/anomaly.h
+ * Bugs: Enter bugs at http://blackfin.uclinux.org/
*
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2, or (at your option)
- * any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; see the file COPYING.
- * If not, write to the Free Software Foundation,
- * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ * Copyright (C) 2004-2007 Analog Devices Inc.
+ * Licensed under the GPL-2 or later.
*/
/* This file shoule be up to date with:
- * - Revision L, 10Aug2006; ADSP-BF561 Silicon Anomaly List
+ * - Revision N, March 28, 2007; ADSP-BF561 Silicon Anomaly List
*/
#ifndef _MACH_ANOMALY_H_
#define _MACH_ANOMALY_H_
-/* We do not support 0.1 or 0.4 silicon - sorry */
-#if (defined(CONFIG_BF_REV_0_1) || defined(CONFIG_BF_REV_0_2) || defined(CONFIG_BF_REV_0_4))
-#error Kernel will not work on BF561 Version 0.1, 0.2, or 0.4
+/* We do not support 0.1, 0.2, or 0.4 silicon - sorry */
+#if __SILICON_REVISION__ < 3 || __SILICON_REVISION__ == 4
+# error Kernel will not work on BF561 silicon version 0.0, 0.1, 0.2, or 0.4
#endif
-/* Issues that are common to 0.5 and 0.3 silicon */
-#if (defined(CONFIG_BF_REV_0_5) || defined(CONFIG_BF_REV_0_3))
-#define ANOMALY_05000074 /* A multi issue instruction with dsp32shiftimm in
- slot1 and store of a P register in slot 2 is not
- supported */
-#define ANOMALY_05000099 /* UART Line Status Register (UART_LSR) bits are not
- updated at the same time. */
-#define ANOMALY_05000120 /* Testset instructions restricted to 32-bit aligned
- memory locations */
-#define ANOMALY_05000122 /* Rx.H cannot be used to access 16-bit System MMR
- registers */
-#define ANOMALY_05000127 /* Signbits instruction not functional under certain
- conditions */
-#define ANOMALY_05000149 /* IMDMA S1/D1 channel may stall */
-#define ANOMALY_05000166 /* PPI Data Lengths Between 8 and 16 do not zero out
- upper bits */
-#define ANOMALY_05000167 /* Turning Serial Ports on With External Frame Syncs */
-#define ANOMALY_05000180 /* PPI_DELAY not functional in PPI modes with 0 frame
- syncs */
-#define ANOMALY_05000182 /* IMDMA does not operate to full speed for 600MHz
- and higher devices */
-#define ANOMALY_05000187 /* IMDMA Corrupted Data after a Halt */
-#define ANOMALY_05000190 /* PPI not functional at core voltage < 1Volt */
-#define ANOMALY_05000208 /* VSTAT status bit in PLL_STAT register is not
- functional */
-#define ANOMALY_05000245 /* Spurious Hardware Error from an access in the
- shadow of a conditional branch */
-#define ANOMALY_05000257 /* Interrupt/Exception during short hardware loop
- may cause bad instruction fetches */
-#define ANOMALY_05000265 /* Sensitivity to noise with slow input edge rates on
- external SPORT TX and RX clocks */
-#define ANOMALY_05000267 /* IMDMA may corrupt data under certain conditions */
-#define ANOMALY_05000269 /* High I/O activity causes output voltage of internal
- voltage regulator (VDDint) to increase */
-#define ANOMALY_05000270 /* High I/O activity causes output voltage of internal
- voltage regulator (VDDint) to decrease */
-#define ANOMALY_05000272 /* Certain data cache write through modes fail for
- VDDint <=0.9V */
-#define ANOMALY_05000274 /* Data cache write back to external synchronous memory
- may be lost */
-#define ANOMALY_05000275 /* PPI Timing and sampling informaton updates */
-#define ANOMALY_05000312 /* Errors when SSYNC, CSYNC, or loads to LT, LB and LC
- registers are interrupted */
+/* Multi-Issue Instruction with dsp32shiftimm in slot1 and P-reg Store in slot 2 Not Supported */
+#define ANOMALY_05000074 (1)
+/* UART Line Status Register (UART_LSR) Bits Are Not Updated at the Same Time */
+#define ANOMALY_05000099 (__SILICON_REVISION__ < 5)
+/* Trace Buffers may contain errors in emulation mode and/or exception, NMI, reset handlers */
+#define ANOMALY_05000116 (__SILICON_REVISION__ < 3)
+/* Testset instructions restricted to 32-bit aligned memory locations */
+#define ANOMALY_05000120 (1)
+/* Rx.H Cannot Be Used to Access 16-bit System MMR Registers */
+#define ANOMALY_05000122 (1)
+/* Erroneous exception when enabling cache */
+#define ANOMALY_05000125 (__SILICON_REVISION__ < 3)
+/* Signbits instruction not functional under certain conditions */
+#define ANOMALY_05000127 (1)
+/* Two bits in the Watchpoint Status Register (WPSTAT) are swapped */
+#define ANOMALY_05000134 (__SILICON_REVISION__ < 3)
+/* Enable wires from the Data Watchpoint Address Control Register (WPDACTL) are swapped */
+#define ANOMALY_05000135 (__SILICON_REVISION__ < 3)
+/* Stall in multi-unit DMA operations */
+#define ANOMALY_05000136 (__SILICON_REVISION__ < 3)
+/* Allowing the SPORT RX FIFO to fill will cause an overflow */
+#define ANOMALY_05000140 (__SILICON_REVISION__ < 3)
+/* Infinite Stall may occur with a particular sequence of consecutive dual dag events */
+#define ANOMALY_05000141 (__SILICON_REVISION__ < 3)
+/* Interrupts may be lost when a programmable input flag is configured to be edge sensitive */
+#define ANOMALY_05000142 (__SILICON_REVISION__ < 3)
+/* DMA and TESTSET conflict when both are accessing external memory */
+#define ANOMALY_05000144 (__SILICON_REVISION__ < 3)
+/* In PWM_OUT mode, you must enable the PPI block to generate a waveform from PPI_CLK */
+#define ANOMALY_05000145 (__SILICON_REVISION__ < 3)
+/* MDMA may lose the first few words of a descriptor chain */
+#define ANOMALY_05000146 (__SILICON_REVISION__ < 3)
+/* Source MDMA descriptor may stop with a DMA Error near beginning of descriptor fetch */
+#define ANOMALY_05000147 (__SILICON_REVISION__ < 3)
+/* IMDMA S1/D1 channel may stall */
+#define ANOMALY_05000149 (1)
+/* DMA engine may lose data due to incorrect handshaking */
+#define ANOMALY_05000150 (__SILICON_REVISION__ < 3)
+/* DMA stalls when all three controllers read data from the same source */
+#define ANOMALY_05000151 (__SILICON_REVISION__ < 3)
+/* Execution stall when executing in L2 and doing external accesses */
+#define ANOMALY_05000152 (__SILICON_REVISION__ < 3)
+/* Frame Delay in SPORT Multichannel Mode */
+#define ANOMALY_05000153 (__SILICON_REVISION__ < 3)
+/* SPORT TFS signal stays active in multichannel mode outside of valid channels */
+#define ANOMALY_05000154 (__SILICON_REVISION__ < 3)
+/* Timers in PWM-Out Mode with PPI GP Receive (Input) Mode with 0 Frame Syncs */
+#define ANOMALY_05000156 (__SILICON_REVISION__ < 4)
+/* Killed 32-bit MMR write leads to next system MMR access thinking it should be 32-bit */
+#define ANOMALY_05000157 (__SILICON_REVISION__ < 3)
+/* DMA Lock-up at CCLK to SCLK ratios of 4:1, 2:1, or 1:1 */
+#define ANOMALY_05000159 (__SILICON_REVISION__ < 3)
+/* A read from external memory may return a wrong value with data cache enabled */
+#define ANOMALY_05000160 (__SILICON_REVISION__ < 3)
+/* Data Cache Fill data can be corrupted after/during Instruction DMA if certain core stalls exist */
+#define ANOMALY_05000161 (__SILICON_REVISION__ < 3)
+/* DMEM_CONTROL<12> is not set on Reset */
+#define ANOMALY_05000162 (__SILICON_REVISION__ < 3)
+/* SPORT transmit data is not gated by external frame sync in certain conditions */
+#define ANOMALY_05000163 (__SILICON_REVISION__ < 3)
+/* PPI Data Lengths Between 8 and 16 Do Not Zero Out Upper Bits */
+#define ANOMALY_05000166 (1)
+/* Turning Serial Ports on with External Frame Syncs */
+#define ANOMALY_05000167 (1)
+/* SDRAM auto-refresh and subsequent Power Ups */
+#define ANOMALY_05000168 (__SILICON_REVISION__ < 5)
+/* DATA CPLB page miss can result in lost write-through cache data writes */
+#define ANOMALY_05000169 (__SILICON_REVISION__ < 5)
+/* Boot-ROM code modifies SICA_IWRx wakeup registers */
+#define ANOMALY_05000171 (__SILICON_REVISION__ < 5)
+/* DSPID register values incorrect */
+#define ANOMALY_05000172 (__SILICON_REVISION__ < 3)
+/* DMA vs Core accesses to external memory */
+#define ANOMALY_05000173 (__SILICON_REVISION__ < 3)
+/* Cache Fill Buffer Data lost */
+#define ANOMALY_05000174 (__SILICON_REVISION__ < 5)
+/* Overlapping Sequencer and Memory Stalls */
+#define ANOMALY_05000175 (__SILICON_REVISION__ < 5)
+/* Multiplication of (-1) by (-1) followed by an accumulator saturation */
+#define ANOMALY_05000176 (__SILICON_REVISION__ < 5)
+/* PPI_COUNT Cannot Be Programmed to 0 in General Purpose TX or RX Modes */
+#define ANOMALY_05000179 (__SILICON_REVISION__ < 5)
+/* PPI_DELAY Not Functional in PPI Modes with 0 Frame Syncs */
+#define ANOMALY_05000180 (1)
+/* Disabling the PPI resets the PPI configuration registers */
+#define ANOMALY_05000181 (__SILICON_REVISION__ < 5)
+/* IMDMA does not operate to full speed for 600MHz and higher devices */
+#define ANOMALY_05000182 (1)
+/* Timer Pin limitations for PPI TX Modes with External Frame Syncs */
+#define ANOMALY_05000184 (__SILICON_REVISION__ < 5)
+/* PPI TX Mode with 2 External Frame Syncs */
+#define ANOMALY_05000185 (__SILICON_REVISION__ < 5)
+/* PPI packing with Data Length greater than 8 bits (not a meaningful mode) */
+#define ANOMALY_05000186 (__SILICON_REVISION__ < 5)
+/* IMDMA Corrupted Data after a Halt */
+#define ANOMALY_05000187 (1)
+/* IMDMA Restrictions on Descriptor and Buffer Placement in Memory */
+#define ANOMALY_05000188 (__SILICON_REVISION__ < 5)
+/* False Protection Exceptions */
+#define ANOMALY_05000189 (__SILICON_REVISION__ < 5)
+/* PPI not functional at core voltage < 1Volt */
+#define ANOMALY_05000190 (1)
+/* PPI does not invert the Driving PPICLK edge in Transmit Modes */
+#define ANOMALY_05000191 (__SILICON_REVISION__ < 3)
+/* False I/O Pin Interrupts on Edge-Sensitive Inputs When Polarity Setting Is Changed */
+#define ANOMALY_05000193 (__SILICON_REVISION__ < 5)
+/* Restarting SPORT in Specific Modes May Cause Data Corruption */
+#define ANOMALY_05000194 (__SILICON_REVISION__ < 5)
+/* Failing MMR Accesses When Stalled by Preceding Memory Read */
+#define ANOMALY_05000198 (__SILICON_REVISION__ < 5)
+/* Current DMA Address Shows Wrong Value During Carry Fix */
+#define ANOMALY_05000199 (__SILICON_REVISION__ < 5)
+/* SPORT TFS and DT Are Incorrectly Driven During Inactive Channels in Certain Conditions */
+#define ANOMALY_05000200 (__SILICON_REVISION__ < 5)
+/* Possible Infinite Stall with Specific Dual-DAG Situation */
+#define ANOMALY_05000202 (__SILICON_REVISION__ < 5)
+/* Incorrect data read with write-through cache and allocate cache lines on reads only mode */
+#define ANOMALY_05000204 (__SILICON_REVISION__ < 5)
+/* Specific sequence that can cause DMA error or DMA stopping */
+#define ANOMALY_05000205 (__SILICON_REVISION__ < 5)
+/* Recovery from "Brown-Out" Condition */
+#define ANOMALY_05000207 (__SILICON_REVISION__ < 5)
+/* VSTAT Status Bit in PLL_STAT Register Is Not Functional */
+#define ANOMALY_05000208 (1)
+/* Speed Path in Computational Unit Affects Certain Instructions */
+#define ANOMALY_05000209 (__SILICON_REVISION__ < 5)
+/* UART TX Interrupt Masked Erroneously */
+#define ANOMALY_05000215 (__SILICON_REVISION__ < 5)
+/* NMI Event at Boot Time Results in Unpredictable State */
+#define ANOMALY_05000219 (__SILICON_REVISION__ < 5)
+/* Data Corruption with Cached External Memory and Non-Cached On-Chip L2 Memory */
+#define ANOMALY_05000220 (__SILICON_REVISION__ < 5)
+/* Incorrect Pulse-Width of UART Start Bit */
+#define ANOMALY_05000225 (__SILICON_REVISION__ < 5)
+/* Scratchpad Memory Bank Reads May Return Incorrect Data */
+#define ANOMALY_05000227 (__SILICON_REVISION__ < 5)
+/* UART Receiver is Less Robust Against Baudrate Differences in Certain Conditions */
+#define ANOMALY_05000230 (__SILICON_REVISION__ < 5)
+/* UART STB Bit Incorrectly Affects Receiver Setting */
+#define ANOMALY_05000231 (__SILICON_REVISION__ < 5)
+/* SPORT data transmit lines are incorrectly driven in multichannel mode */
+#define ANOMALY_05000232 (__SILICON_REVISION__ < 5)
+/* DF Bit in PLL_CTL Register Does Not Respond to Hardware Reset */
+#define ANOMALY_05000242 (__SILICON_REVISION__ < 5)
+/* If I-Cache Is On, CSYNC/SSYNC/IDLE Around Change of Control Causes Failures */
+#define ANOMALY_05000244 (__SILICON_REVISION__ < 5)
+/* Spurious Hardware Error from an Access in the Shadow of a Conditional Branch */
+#define ANOMALY_05000245 (__SILICON_REVISION__ < 5)
+/* TESTSET operation forces stall on the other core */
+#define ANOMALY_05000248 (__SILICON_REVISION__ < 5)
+/* Incorrect Bit Shift of Data Word in Multichannel (TDM) Mode in Certain Conditions */
+#define ANOMALY_05000250 (__SILICON_REVISION__ > 2 && __SILICON_REVISION__ < 5)
+/* Exception Not Generated for MMR Accesses in Reserved Region */
+#define ANOMALY_05000251 (__SILICON_REVISION__ < 5)
+/* Maximum External Clock Speed for Timers */
+#define ANOMALY_05000253 (__SILICON_REVISION__ < 5)
+/* Incorrect Timer Pulse Width in Single-Shot PWM_OUT Mode with External Clock */
+#define ANOMALY_05000254 (__SILICON_REVISION__ > 3)
+/* Interrupt/Exception During Short Hardware Loop May Cause Bad Instruction Fetches */
+#define ANOMALY_05000257 (__SILICON_REVISION__ < 5)
+/* Instruction Cache Is Corrupted When Bits 9 and 12 of the ICPLB Data Registers Differ */
+#define ANOMALY_05000258 (__SILICON_REVISION__ < 5)
+/* ICPLB_STATUS MMR Register May Be Corrupted */
+#define ANOMALY_05000260 (__SILICON_REVISION__ < 5)
+/* DCPLB_FAULT_ADDR MMR Register May Be Corrupted */
+#define ANOMALY_05000261 (__SILICON_REVISION__ < 5)
+/* Stores To Data Cache May Be Lost */
+#define ANOMALY_05000262 (__SILICON_REVISION__ < 5)
+/* Hardware Loop Corrupted When Taking an ICPLB Exception */
+#define ANOMALY_05000263 (__SILICON_REVISION__ < 5)
+/* CSYNC/SSYNC/IDLE Causes Infinite Stall in Penultimate Instruction in Hardware Loop */
+#define ANOMALY_05000264 (__SILICON_REVISION__ < 5)
+/* Sensitivity To Noise with Slow Input Edge Rates on External SPORT TX and RX Clocks */
+#define ANOMALY_05000265 (__SILICON_REVISION__ < 5)
+/* IMDMA destination IRQ status must be read prior to using IMDMA */
+#define ANOMALY_05000266 (__SILICON_REVISION__ > 3)
+/* IMDMA may corrupt data under certain conditions */
+#define ANOMALY_05000267 (1)
+/* High I/O Activity Causes Output Voltage of Internal Voltage Regulator (Vddint) to Increase */
+#define ANOMALY_05000269 (1)
+/* High I/O Activity Causes Output Voltage of Internal Voltage Regulator (Vddint) to Decrease */
+#define ANOMALY_05000270 (1)
+/* Certain Data Cache Writethrough Modes Fail for Vddint <= 0.9V */
+#define ANOMALY_05000272 (1)
+/* Data cache write back to external synchronous memory may be lost */
+#define ANOMALY_05000274 (1)
+/* PPI Timing and Sampling Information Updates */
+#define ANOMALY_05000275 (__SILICON_REVISION__ > 2)
+/* Timing Requirements Change for External Frame Sync PPI Modes with Non-Zero PPI_DELAY */
+#define ANOMALY_05000276 (__SILICON_REVISION__ < 5)
+/* Disabling Peripherals with DMA Running May Cause DMA System Instability */
+#define ANOMALY_05000278 (__SILICON_REVISION__ < 5)
+/* False Hardware Error Exception When ISR Context Is Not Restored */
+#define ANOMALY_05000281 (__SILICON_REVISION__ < 5)
+/* System MMR Write Is Stalled Indefinitely When Killed in a Particular Stage */
+#define ANOMALY_05000283 (1)
+/* A read will receive incorrect data under certain conditions */
+#define ANOMALY_05000287 (__SILICON_REVISION__ < 5)
+/* SPORTs May Receive Bad Data If FIFOs Fill Up */
+#define ANOMALY_05000288 (__SILICON_REVISION__ < 5)
+/* Memory-To-Memory DMA Source/Destination Descriptors Must Be in Same Memory Space */
+#define ANOMALY_05000301 (1)
+/* SSYNCs After Writes To DMA MMR Registers May Not Be Handled Correctly */
+#define ANOMALY_05000302 (1)
+/* New Feature: Additional Hysteresis on SPORT Input Pins (Not Available On Older Silicon) */
+#define ANOMALY_05000305 (__SILICON_REVISION__ < 5)
+/* SCKELOW Bit Does Not Maintain State Through Hibernate */
+#define ANOMALY_05000307 (__SILICON_REVISION__ < 5)
+/* False Hardware Errors Caused by Fetches at the Boundary of Reserved Memory */
+#define ANOMALY_05000310 (1)
+/* Errors When SSYNC, CSYNC, or Loads to LT, LB and LC Registers Are Interrupted */
+#define ANOMALY_05000312 (1)
+/* PPI Is Level-Sensitive on First Transfer */
+#define ANOMALY_05000313 (1)
+/* Killed System MMR Write Completes Erroneously On Next System MMR Access */
+#define ANOMALY_05000315 (1)
+/* PF2 Output Remains Asserted After SPI Master Boot */
+#define ANOMALY_05000320 (__SILICON_REVISION__ > 3)
+/* Erroneous GPIO Flag Pin Operations Under Specific Sequences */
+#define ANOMALY_05000323 (1)
+/* SPORT Secondary Receive Channel Not Functional When Word Length Exceeds 16 Bits */
+#define ANOMALY_05000326 (__SILICON_REVISION__ > 3)
+/* New Feature: 24-Bit SPI Boot Mode Support (Not Available On Older Silicon) */
+#define ANOMALY_05000331 (__SILICON_REVISION__ < 5)
+/* New Feature: Slave SPI Boot Mode Supported (Not Available On Older Silicon) */
+#define ANOMALY_05000332 (__SILICON_REVISION__ < 5)
+/* Flag Data Register Writes One SCLK Cycle After Edge Is Detected May Clear Interrupt Status */
+#define ANOMALY_05000333 (__SILICON_REVISION__ < 5)
-#endif /* (defined(CONFIG_BF_REV_0_5) || defined(CONFIG_BF_REV_0_3)) */
+/* Anomalies that don't exist on this proc */
+#define ANOMALY_05000158 (0)
+#define ANOMALY_05000183 (0)
+#define ANOMALY_05000273 (0)
+#define ANOMALY_05000311 (0)
-#if (defined(CONFIG_BF_REV_0_5))
-#define ANOMALY_05000254 /* Incorrect Timer Pulse Width in Single-Shot PWM_OUT
- mode with external clock */
-#define ANOMALY_05000266 /* IMDMA destination IRQ status must be read prior to
- using IMDMA */
#endif
-
-#if (defined(CONFIG_BF_REV_0_3))
-#define ANOMALY_05000156 /* Timers in PWM-Out Mode with PPI GP Receive (Input)
- Mode with 0 Frame Syncs */
-#define ANOMALY_05000168 /* SDRAM auto-refresh and subsequent Power Ups */
-#define ANOMALY_05000169 /* DATA CPLB page miss can result in lost write-through
- cache data writes */
-#define ANOMALY_05000171 /* Boot-ROM code modifies SICA_IWRx wakeup registers */
-#define ANOMALY_05000174 /* Cache Fill Buffer Data lost */
-#define ANOMALY_05000175 /* Overlapping Sequencer and Memory Stalls */
-#define ANOMALY_05000176 /* Multiplication of (-1) by (-1) followed by an
- accumulator saturation */
-#define ANOMALY_05000179 /* PPI_COUNT cannot be programmed to 0 in General
- Purpose TX or RX modes */
-#define ANOMALY_05000181 /* Disabling the PPI resets the PPI configuration
- registers */
-#define ANOMALY_05000184 /* Timer Pin limitations for PPI TX Modes with
- External Frame Syncs */
-#define ANOMALY_05000185 /* PPI TX Mode with 2 External Frame Syncs */
-#define ANOMALY_05000186 /* PPI packing with Data Length greater than 8 bits
- (not a meaningful mode) */
-#define ANOMALY_05000188 /* IMDMA Restrictions on Descriptor and Buffer
- Placement in Memory */
-#define ANOMALY_05000189 /* False Protection Exception */
-#define ANOMALY_05000193 /* False Flag Pin Interrupts on Edge Sensitive Inputs
- when polarity setting is changed */
-#define ANOMALY_05000194 /* Restarting SPORT in specific modes may cause data
- corruption */
-#define ANOMALY_05000198 /* Failing MMR accesses when stalled by preceding
- memory read */
-#define ANOMALY_05000199 /* DMA current address shows wrong value during carry
- fix */
-#define ANOMALY_05000200 /* SPORT TFS and DT are incorrectly driven during
- inactive channels in certain conditions */
-#define ANOMALY_05000202 /* Possible infinite stall with specific dual-DAG
- situation */
-#define ANOMALY_05000204 /* Incorrect data read with write-through cache and
- allocate cache lines on reads only mode */
-#define ANOMALY_05000205 /* Specific sequence that can cause DMA error or DMA
- stopping */
-#define ANOMALY_05000207 /* Recovery from "brown-out" condition */
-#define ANOMALY_05000209 /* Speed-Path in computational unit affects certain
- instructions */
-#define ANOMALY_05000215 /* UART TX Interrupt masked erroneously */
-#define ANOMALY_05000219 /* NMI event at boot time results in unpredictable
- state */
-#define ANOMALY_05000220 /* Data Corruption with Cached External Memory and
- Non-Cached On-Chip L2 Memory */
-#define ANOMALY_05000225 /* Incorrect pulse-width of UART start-bit */
-#define ANOMALY_05000227 /* Scratchpad memory bank reads may return incorrect
- data */
-#define ANOMALY_05000230 /* UART Receiver is less robust against Baudrate
- Differences in certain Conditions */
-#define ANOMALY_05000231 /* UART STB bit incorrectly affects receiver setting */
-#define ANOMALY_05000232 /* SPORT data transmit lines are incorrectly driven in
- multichannel mode */
-#define ANOMALY_05000242 /* DF bit in PLL_CTL register does not respond to
- hardware reset */
-#define ANOMALY_05000244 /* If i-cache is on, CSYNC/SSYNC/IDLE around Change of
- Control causes failures */
-#define ANOMALY_05000248 /* TESTSET operation forces stall on the other core */
-#define ANOMALY_05000250 /* Incorrect Bit-Shift of Data Word in Multichannel
- (TDM) mode in certain conditions */
-#define ANOMALY_05000251 /* Exception not generated for MMR accesses in
- reserved region */
-#define ANOMALY_05000253 /* Maximum external clock speed for Timers */
-#define ANOMALY_05000258 /* Instruction Cache is corrupted when bits 9 and 12
- of the ICPLB Data registers differ */
-#define ANOMALY_05000260 /* ICPLB_STATUS MMR register may be corrupted */
-#define ANOMALY_05000261 /* DCPLB_FAULT_ADDR MMR register may be corrupted */
-#define ANOMALY_05000262 /* Stores to data cache may be lost */
-#define ANOMALY_05000263 /* Hardware loop corrupted when taking an ICPLB
- exception */
-#define ANOMALY_05000264 /* CSYNC/SSYNC/IDLE causes infinite stall in second
- to last instruction in hardware loop */
-#define ANOMALY_05000276 /* Timing requirements change for External Frame
- Sync PPI Modes with non-zero PPI_DELAY */
-#define ANOMALY_05000278 /* Disabling Peripherals with DMA running may cause
- DMA system instability */
-#define ANOMALY_05000281 /* False Hardware Error Exception when ISR context is
- not restored */
-#define ANOMALY_05000283 /* An MMR write is stalled indefinitely when killed
- in a particular stage */
-#define ANOMALY_05000287 /* A read will receive incorrect data under certain
- conditions */
-#define ANOMALY_05000288 /* SPORTs may receive bad data if FIFOs fill up */
-#endif
-
-#endif /* _MACH_ANOMALY_H_ */
*/
-#define BLKFIN_ISUBBANKS 4
-#define BLKFIN_IWAYS 4
-#define BLKFIN_ILINES 32
+#define BFIN_ISUBBANKS 4
+#define BFIN_IWAYS 4
+#define BFIN_ILINES 32
-#define BLKFIN_DSUBBANKS 4
-#define BLKFIN_DWAYS 2
-#define BLKFIN_DLINES 64
+#define BFIN_DSUBBANKS 4
+#define BFIN_DWAYS 2
+#define BFIN_DLINES 64
#define WAY0_L 0x1
#define WAY1_L 0x2
#define AMGCTLVAL (V_AMBEN | V_AMCKEN | V_CDPRIO | V_B0PEN | V_B1PEN | V_B2PEN | V_B3PEN | 0x0002)
-#define MAX_VC 600000000
-#define MIN_VC 50000000
-
-/******************************* PLL Settings ********************************/
-#ifdef CONFIG_BFIN_KERNEL_CLOCK
-#if (CONFIG_VCO_MULT < 0)
-#error "VCO Multiplier is less than 0. Please select a different value"
-#endif
-
-#if (CONFIG_VCO_MULT == 0)
-#error "VCO Multiplier should be greater than 0. Please select a different value"
-#endif
-
-#ifndef CONFIG_CLKIN_HALF
-#define CONFIG_VCO_HZ (CONFIG_CLKIN_HZ * CONFIG_VCO_MULT)
-#else
-#define CONFIG_VCO_HZ ((CONFIG_CLKIN_HZ * CONFIG_VCO_MULT)/2)
-#endif
-
-#ifndef CONFIG_PLL_BYPASS
-#define CONFIG_CCLK_HZ (CONFIG_VCO_HZ/CONFIG_CCLK_DIV)
-#define CONFIG_SCLK_HZ (CONFIG_VCO_HZ/CONFIG_SCLK_DIV)
-#else
-#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ
-#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ
-#endif
-
-#if (CONFIG_SCLK_DIV < 1)
-#error "SCLK DIV cannot be less than 1 or more than 15. Please select a proper value"
-#endif
-
-#if (CONFIG_SCLK_DIV > 15)
-#error "SCLK DIV cannot be less than 1 or more than 15. Please select a proper value"
-#endif
-
-#if (CONFIG_CCLK_DIV != 1)
-#if (CONFIG_CCLK_DIV != 2)
-#if (CONFIG_CCLK_DIV != 4)
-#if (CONFIG_CCLK_DIV != 8)
-#error "CCLK DIV can be 1,2,4 or 8 only. Please select a proper value"
-#endif
-#endif
-#endif
-#endif
-
-#if (CONFIG_VCO_HZ > MAX_VC)
-#error "VCO selected is more than maximum value. Please change the VCO multipler"
-#endif
-
-#if (CONFIG_SCLK_HZ > 133000000)
-#error "Sclk value selected is more than maximum. Please select a proper value for SCLK multiplier"
-#endif
-
-#if (CONFIG_SCLK_HZ < 27000000)
-#error "Sclk value selected is less than minimum. Please select a proper value for SCLK multiplier"
-#endif
-
-#if (CONFIG_SCLK_HZ >= CONFIG_CCLK_HZ)
-#if (CONFIG_SCLK_HZ != CONFIG_CLKIN_HZ)
-#if (CONFIG_CCLK_HZ != CONFIG_CLKIN_HZ)
-#error "Please select sclk less than cclk"
-#endif
-#endif
-#endif
-
-#if (CONFIG_CCLK_DIV == 1)
-#define CONFIG_CCLK_ACT_DIV CCLK_DIV1
-#endif
-#if (CONFIG_CCLK_DIV == 2)
-#define CONFIG_CCLK_ACT_DIV CCLK_DIV2
-#endif
-#if (CONFIG_CCLK_DIV == 4)
-#define CONFIG_CCLK_ACT_DIV CCLK_DIV4
-#endif
-#if (CONFIG_CCLK_DIV == 8)
-#define CONFIG_CCLK_ACT_DIV CCLK_DIV8
-#endif
-#ifndef CONFIG_CCLK_ACT_DIV
-#define CONFIG_CCLK_ACT_DIV CONFIG_CCLK_DIV_not_defined_properly
-#endif
-
-#if defined(ANOMALY_05000273) && (CONFIG_CCLK_DIV == 1)
-#error ANOMALY 05000273, please make sure CCLK is at least 2x SCLK
-#endif
-
-#endif /* CONFIG_BFIN_KERNEL_CLOCK */
-
#ifdef CONFIG_BF561
#define CPU "BF561"
#define CPUID 0x027bb000
#define CPUID 0x0
#endif
-#if (CONFIG_MEM_SIZE % 4)
-#error "SDRAM memory size must be a multiple of 4MB!"
-#endif
-#define SDRAM_IGENERIC (CPLB_L1_CHBL | CPLB_USER_RD | CPLB_VALID | CPLB_PORTPRIO)
-#define SDRAM_IKERNEL (SDRAM_IGENERIC | CPLB_LOCK)
-#define L1_IMEMORY ( CPLB_USER_RD | CPLB_VALID | CPLB_LOCK)
-#define SDRAM_INON_CHBL ( CPLB_USER_RD | CPLB_VALID)
-
-/*Use the menuconfig cache policy here - CONFIG_BLKFIN_WT/CONFIG_BLKFIN_WB*/
-
-#define ANOMALY_05000158_WORKAROUND 0x200
-#ifdef CONFIG_BLKFIN_WB /*Write Back Policy */
-#define SDRAM_DGENERIC (CPLB_L1_CHBL | CPLB_DIRTY \
- | CPLB_SUPV_WR | CPLB_USER_WR | CPLB_USER_RD | CPLB_VALID | ANOMALY_05000158_WORKAROUND)
-#else /*Write Through */
-#define SDRAM_DGENERIC (CPLB_L1_CHBL | CPLB_WT | CPLB_L1_AOW | CPLB_DIRTY \
- | CPLB_SUPV_WR | CPLB_USER_WR | CPLB_USER_RD | CPLB_VALID | ANOMALY_05000158_WORKAROUND)
-#endif
-
-
-#define L1_DMEMORY (CPLB_SUPV_WR | CPLB_USER_WR | CPLB_USER_RD | CPLB_VALID | ANOMALY_05000158_WORKAROUND | CPLB_LOCK | CPLB_DIRTY)
-#define SDRAM_DNON_CHBL (CPLB_SUPV_WR | CPLB_USER_WR | CPLB_USER_RD | CPLB_VALID | ANOMALY_05000158_WORKAROUND | CPLB_DIRTY)
-#define SDRAM_EBIU (CPLB_SUPV_WR | CPLB_USER_WR | CPLB_USER_RD | CPLB_VALID | ANOMALY_05000158_WORKAROUND | CPLB_DIRTY)
-#define SDRAM_OOPS (CPLB_VALID | ANOMALY_05000158_WORKAROUND | CPLB_LOCK | CPLB_DIRTY)
-
-#define L2_MEMORY (CPLB_SUPV_WR | CPLB_USER_WR | CPLB_USER_RD | CPLB_VALID | ANOMALY_05000158_WORKAROUND | CPLB_DIRTY)
-
-#define SIZE_1K 0x00000400 /* 1K */
-#define SIZE_4K 0x00001000 /* 4K */
-#define SIZE_1M 0x00100000 /* 1M */
-#define SIZE_4M 0x00400000 /* 4M */
-
-#define MAX_CPLBS (16 * 2)
-
-/*
-* Number of required data CPLB switchtable entries
-* MEMSIZE / 4 (we mostly install 4M page size CPLBs
-* approx 16 for smaller 1MB page size CPLBs for allignment purposes
-* 1 for L1 Data Memory
-* 1 for L2 Data Memory
-* 1 for CONFIG_DEBUG_HUNT_FOR_ZERO
-* 64 for ASYNC Memory
-*/
-
-
-#define MAX_SWITCH_D_CPLBS (((CONFIG_MEM_SIZE / 4) + 16 + 1 + 1 + 1 + 64) * 2)
-
-/*
-* Number of required instruction CPLB switchtable entries
-* MEMSIZE / 4 (we mostly install 4M page size CPLBs
-* approx 12 for smaller 1MB page size CPLBs for allignment purposes
-* 1 for L1 Instruction Memory
-* 1 for L2 Instruction Memory
-* 1 for CONFIG_DEBUG_HUNT_FOR_ZERO
-*/
-
-#define MAX_SWITCH_I_CPLBS (((CONFIG_MEM_SIZE / 4) + 12 + 1 + 1 + 1) * 2)
-
-#if 0 /* comment by mhfan */
-/* Event Vector Table Address */
-#define EVT_EMULATION_ADDR 0xffe02000
-#define EVT_RESET_ADDR 0xffe02004
-#define EVT_NMI_ADDR 0xffe02008
-#define EVT_EXCEPTION_ADDR 0xffe0200c
-#define EVT_GLOBAL_INT_ENB_ADDR 0xffe02010
-#define EVT_HARDWARE_ERROR_ADDR 0xffe02014
-#define EVT_TIMER_ADDR 0xffe02018
-#define EVT_IVG7_ADDR 0xffe0201c
-#define EVT_IVG8_ADDR 0xffe02020
-#define EVT_IVG9_ADDR 0xffe02024
-#define EVT_IVG10_ADDR 0xffe02028
-#define EVT_IVG11_ADDR 0xffe0202c
-#define EVT_IVG12_ADDR 0xffe02030
-#define EVT_IVG13_ADDR 0xffe02034
-#define EVT_IVG14_ADDR 0xffe02038
-#define EVT_IVG15_ADDR 0xffe0203c
-#define EVT_OVERRIDE_ADDR 0xffe02100
-#endif /* comment by mhfan */
-
#endif /* __MACH_BF561_H__ */
#include "defBF561.h"
#include "anomaly.h"
-#if !(defined(__ASSEMBLY__) || defined(ASSEMBLY))
+#if !defined(__ASSEMBLY__)
#include "cdefBF561.h"
#endif
#ifndef _CDEF_BF561_H
#define _CDEF_BF561_H
-/*
-#if !defined(__ADSPBF561__)
-#warning cdefBF561.h should only be included for BF561 chip.
-#endif
-*/
+#include <asm/blackfin.h>
+
/* include all Core registers and bit definitions */
#include "defBF561.h"
bfin_write32(SICA_IWR1, 0);
bfin_write16(VR_CTL, val);
- __builtin_bfin_ssync();
+ SSYNC();
local_irq_save(flags);
asm("IDLE;");
#define UART_GCTL 0xFFC00424 /* Global Control Register */
/* SPI Controller (0xFFC00500 - 0xFFC005FF) */
+#define SPI0_REGBASE 0xFFC00500
#define SPI_CTL 0xFFC00500 /* SPI Control Register */
#define SPI_FLG 0xFFC00504 /* SPI Flag register */
#define SPI_STAT 0xFFC00508 /* SPI Status register */
#define IRQ_PF46 119
#define IRQ_PF47 120
+#define GPIO_IRQ_BASE IRQ_PF0
+
#ifdef CONFIG_IRQCHIP_DEMUX_GPIO
#define NR_IRQS (IRQ_PF47 + 1)
#else
/* Level 1 Memory */
-#ifdef CONFIG_BLKFIN_CACHE
-#define BLKFIN_ICACHESIZE (16*1024)
+#ifdef CONFIG_BFIN_ICACHE
+#define BFIN_ICACHESIZE (16*1024)
#else
-#define BLKFIN_ICACHESIZE (0*1024)
+#define BFIN_ICACHESIZE (0*1024)
#endif
/* Memory Map for ADSP-BF561 processors */
#define L1_CODE_LENGTH 0x4000
-#ifdef CONFIG_BLKFIN_DCACHE
+#ifdef CONFIG_BFIN_DCACHE
-#ifdef CONFIG_BLKFIN_DCACHE_BANKA
+#ifdef CONFIG_BFIN_DCACHE_BANKA
#define DMEM_CNTR (ACACHE_BSRAM | ENDCPLB | PORT_PREF0)
#define L1_DATA_A_LENGTH (0x8000 - 0x4000)
#define L1_DATA_B_LENGTH 0x8000
-#define BLKFIN_DCACHESIZE (16*1024)
-#define BLKFIN_DSUPBANKS 1
+#define BFIN_DCACHESIZE (16*1024)
+#define BFIN_DSUPBANKS 1
#else
#define DMEM_CNTR (ACACHE_BCACHE | ENDCPLB | PORT_PREF0)
#define L1_DATA_A_LENGTH (0x8000 - 0x4000)
#define L1_DATA_B_LENGTH (0x8000 - 0x4000)
-#define BLKFIN_DCACHESIZE (32*1024)
-#define BLKFIN_DSUPBANKS 2
+#define BFIN_DCACHESIZE (32*1024)
+#define BFIN_DSUPBANKS 2
#endif
#else
#define DMEM_CNTR (ASRAM_BSRAM | ENDCPLB | PORT_PREF0)
#define L1_DATA_A_LENGTH 0x8000
#define L1_DATA_B_LENGTH 0x8000
-#define BLKFIN_DCACHESIZE (0*1024)
-#define BLKFIN_DSUPBANKS 0
-#endif /*CONFIG_BLKFIN_DCACHE*/
+#define BFIN_DCACHESIZE (0*1024)
+#define BFIN_DSUPBANKS 0
+#endif /*CONFIG_BFIN_DCACHE*/
#endif
/* Level 2 Memory */
#define P_TMR1 (P_DEFINED | P_IDENT(GPIO_PF1))
#define P_TMR0 (P_DEFINED | P_IDENT(GPIO_PF0))
#define P_SPI0_MOSI (P_DONTCARE)
-#define P_SPI0_MIS0 (P_DONTCARE)
+#define P_SPI0_MISO (P_DONTCARE)
#define P_SPI0_SCK (P_DONTCARE)
#endif /* _MACH_PORTMUX_H_ */
#define bfin_read_SRAM_BASE_ADDRESS() bfin_read32(SRAM_BASE_ADDRESS)
#define bfin_write_SRAM_BASE_ADDRESS(val) bfin_write32(SRAM_BASE_ADDRESS,val)
#define bfin_read_DMEM_CONTROL() bfin_read32(DMEM_CONTROL)
-#ifdef ANOMALY_05000125
+#if ANOMALY_05000125
extern void bfin_write_DMEM_CONTROL(unsigned int val);
#else
#define bfin_write_DMEM_CONTROL(val) bfin_write32(DMEM_CONTROL,val)
#define DTEST_DATA3 0xFFE0040C
*/
#define bfin_read_IMEM_CONTROL() bfin_read32(IMEM_CONTROL)
-#ifdef ANOMALY_05000125
+#if ANOMALY_05000125
extern void bfin_write_IMEM_CONTROL(unsigned int val);
#else
#define bfin_write_IMEM_CONTROL(val) bfin_write32(IMEM_CONTROL,val)
--- /dev/null
+/*
+ * File: include/asm-blackfin/mach-common/clocks.h
+ * Based on: include/asm-blackfin/mach-bf537/bf537.h
+ * Author: Robin Getz <rgetz@blackfin.uclinux.org>
+ *
+ * Created: 25Jul07
+ * Description: Common Clock definitions for various kernel files
+ *
+ * Modified:
+ * Copyright 2004-2007 Analog Devices Inc.
+ *
+ * Bugs: Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see the file COPYING, or write
+ * to the Free Software Foundation, Inc.,
+ * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#ifndef _BFIN_CLOCKS_H
+#define _BFIN_CLOCKS_H
+
+#ifdef CONFIG_CCLK_DIV_1
+# define CONFIG_CCLK_ACT_DIV CCLK_DIV1
+# define CONFIG_CCLK_DIV 1
+#endif
+
+#ifdef CONFIG_CCLK_DIV_2
+# define CONFIG_CCLK_ACT_DIV CCLK_DIV2
+# define CONFIG_CCLK_DIV 2
+#endif
+
+#ifdef CONFIG_CCLK_DIV_4
+# define CONFIG_CCLK_ACT_DIV CCLK_DIV4
+# define CONFIG_CCLK_DIV 4
+#endif
+
+#ifdef CONFIG_CCLK_DIV_8
+# define CONFIG_CCLK_ACT_DIV CCLK_DIV8
+# define CONFIG_CCLK_DIV 8
+#endif
+
+#ifndef CONFIG_PLL_BYPASS
+# ifndef CONFIG_CLKIN_HALF
+# define CONFIG_VCO_HZ (CONFIG_CLKIN_HZ * CONFIG_VCO_MULT)
+# else
+# define CONFIG_VCO_HZ ((CONFIG_CLKIN_HZ * CONFIG_VCO_MULT)/2)
+# endif
+
+# define CONFIG_CCLK_HZ (CONFIG_VCO_HZ/CONFIG_CCLK_DIV)
+# define CONFIG_SCLK_HZ (CONFIG_VCO_HZ/CONFIG_SCLK_DIV)
+
+#else
+# define CONFIG_VCO_HZ (CONFIG_CLKIN_HZ)
+# define CONFIG_CCLK_HZ (CONFIG_CLKIN_HZ)
+# define CONFIG_SCLK_HZ (CONFIG_CLKIN_HZ)
+# define CONFIG_VCO_MULT 0
+#endif
+
+#endif
#include <asm/mach/anomaly.h>
-/*#if !defined(__ADSPLPBLACKFIN__)
-#warning def_LPBlackfin.h should only be included for 532 compatible chips.
-#endif
-*/
-
#define MK_BMSK_(x) (1<<x)
-#if defined(ANOMALY_05000198)
-
-#define bfin_read8(addr) ({ unsigned char __v; \
- __asm__ __volatile__ ("NOP;\n\t" \
- "%0 = b[%1] (z);\n\t" \
- : "=d"(__v) : "a"(addr)); \
- __v; })
-
-#define bfin_read16(addr) ({ unsigned __v; \
- __asm__ __volatile__ ("NOP;\n\t"\
- "%0 = w[%1] (z);\n\t"\
- : "=d"(__v) : "a"(addr)); (unsigned short)__v; })
-
-#define bfin_read32(addr) ({ unsigned __v; \
- __asm__ __volatile__ ("NOP;\n\t"\
- "%0 = [%1];\n\t"\
- : "=d"(__v) : "a"(addr)); __v; })
-
-#define bfin_write8(addr, val) ({ \
- __asm__ __volatile__ ("NOP;\n\t" \
- "b[%0] = %1;\n\t" \
- : : "a"(addr), "d"(val) : "memory");})
+#ifndef __ASSEMBLY__
-#define bfin_write16(addr,val) ({\
- __asm__ __volatile__ ("NOP;\n\t"\
- "w[%0] = %1;\n\t"\
- : : "a"(addr) , "d"(val) : "memory");})
-
-#define bfin_write32(addr,val) ({\
- __asm__ __volatile__ ("NOP;\n\t"\
- "[%0] = %1;\n\t"\
- : : "a"(addr) , "d"(val) : "memory");})
+#include <linux/types.h>
+#if ANOMALY_05000198
+# define NOP_PAD_ANOMALY_05000198 "nop;"
#else
-
-#define bfin_read8(addr) ({ unsigned char __v; \
- __asm__ __volatile__ ( \
- "%0 = b[%1] (z);\n\t" \
- :"=d"(__v) : "a"(addr)); \
- __v; })
-
-#define bfin_read16(addr) ({ unsigned __v; \
- __asm__ __volatile__ (\
- "%0 = w[%1] (z);\n\t"\
- : "=d"(__v) : "a"(addr)); (unsigned short)__v; })
-
-#define bfin_read32(addr) ({ unsigned __v; \
- __asm__ __volatile__ (\
- "%0 = [%1];\n\t"\
- : "=d"(__v) : "a"(addr)); __v; })
-
-#define bfin_write8(addr, val) ({ \
- __asm__ __volatile__ ( \
- "b[%0] = %1; \n\t" \
- ::"a"(addr), "d"(val) : "memory");})
-
-#define bfin_write16(addr,val) ({\
- __asm__ __volatile__ (\
- "w[%0] = %1;\n\t"\
- : : "a"(addr) , "d"(val) : "memory");})
-
-#define bfin_write32(addr,val) ({\
- __asm__ __volatile__ (\
- "[%0] = %1;\n\t"\
- : : "a"(addr) , "d"(val) : "memory");})
-
+# define NOP_PAD_ANOMALY_05000198
#endif
+#define bfin_read8(addr) ({ \
+ uint8_t __v; \
+ __asm__ __volatile__( \
+ NOP_PAD_ANOMALY_05000198 \
+ "%0 = b[%1] (z);" \
+ : "=d" (__v) \
+ : "a" (addr) \
+ ); \
+ __v; })
+
+#define bfin_read16(addr) ({ \
+ uint16_t __v; \
+ __asm__ __volatile__( \
+ NOP_PAD_ANOMALY_05000198 \
+ "%0 = w[%1] (z);" \
+ : "=d" (__v) \
+ : "a" (addr) \
+ ); \
+ __v; })
+
+#define bfin_read32(addr) ({ \
+ uint32_t __v; \
+ __asm__ __volatile__( \
+ NOP_PAD_ANOMALY_05000198 \
+ "%0 = [%1];" \
+ : "=d" (__v) \
+ : "a" (addr) \
+ ); \
+ __v; })
+
+#define bfin_write8(addr, val) \
+ __asm__ __volatile__( \
+ NOP_PAD_ANOMALY_05000198 \
+ "b[%0] = %1;" \
+ : \
+ : "a" (addr), "d" (val) \
+ : "memory" \
+ )
+
+#define bfin_write16(addr, val) \
+ __asm__ __volatile__( \
+ NOP_PAD_ANOMALY_05000198 \
+ "w[%0] = %1;" \
+ : \
+ : "a" (addr), "d" (val) \
+ : "memory" \
+ )
+
+#define bfin_write32(addr, val) \
+ __asm__ __volatile__( \
+ NOP_PAD_ANOMALY_05000198 \
+ "[%0] = %1;" \
+ : \
+ : "a" (addr), "d" (val) \
+ : "memory" \
+ )
+
+#endif /* __ASSEMBLY__ */
+
/**************************************************
* System Register Bits
**************************************************/
#define CPLB_USER_RD 0x00000004 /* 0=no read access, 1=read access
* allowed (user mode)
*/
+
#define PAGE_SIZE_1KB 0x00000000 /* 1 KB page size */
#define PAGE_SIZE_4KB 0x00010000 /* 4 KB page size */
#define PAGE_SIZE_1MB 0x00020000 /* 1 MB page size */
*/
#define CPLB_WT 0x00004000 /* 0=write-back, 1=write-through */
+#define CPLB_ALL_ACCESS CPLB_SUPV_WR | CPLB_USER_RD | CPLB_USER_WR
+
/* TBUFCTL Masks */
#define TBUFPWR 0x0001
#define TBUFEN 0x0002
#include <asm-generic/4level-fixup.h>
#include <asm/page.h>
-#include <asm/cplb.h>
+#include <asm/mach-common/def_LPBlackfin.h>
typedef pte_t *pte_addr_t;
/*
--- /dev/null
+/*
+ * include/asm-blackfin/reboot.h - shutdown/reboot header
+ *
+ * Copyright 2004-2007 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#ifndef __ASM_REBOOT_H__
+#define __ASM_REBOOT_H__
+
+/* optional board specific hooks */
+extern void native_machine_restart(char *cmd);
+extern void native_machine_halt(void);
+extern void native_machine_power_off(void);
+
+/* common reboot workarounds */
+extern void bfin_gpio_reset_spi0_ssel1(void);
+
+#endif
#include <linux/linkage.h>
#include <linux/compiler.h>
+#include <asm/mach/anomaly.h>
/*
* Interrupt configuring macros.
extern unsigned long irq_flags;
-#define local_irq_enable() do { \
- __asm__ __volatile__ ( \
- "sti %0;" \
- ::"d"(irq_flags)); \
-} while (0)
+#define local_irq_enable() \
+ __asm__ __volatile__( \
+ "sti %0;" \
+ : \
+ : "d" (irq_flags) \
+ )
-#define local_irq_disable() do { \
- int _tmp_dummy; \
- __asm__ __volatile__ ( \
- "cli %0;" \
- :"=d" (_tmp_dummy):); \
-} while (0)
+#define local_irq_disable() \
+ do { \
+ int __tmp_dummy; \
+ __asm__ __volatile__( \
+ "cli %0;" \
+ : "=d" (__tmp_dummy) \
+ ); \
+ } while (0)
-#if defined(ANOMALY_05000244) && defined (CONFIG_BLKFIN_CACHE)
-#define idle_with_irq_disabled() do { \
- __asm__ __volatile__ ( \
- "nop; nop;\n" \
- ".align 8;\n" \
- "sti %0; idle;\n" \
- ::"d" (irq_flags)); \
-} while (0)
+#if ANOMALY_05000244 && defined(CONFIG_BFIN_ICACHE)
+# define NOP_PAD_ANOMALY_05000244 "nop; nop;"
#else
-#define idle_with_irq_disabled() do { \
- __asm__ __volatile__ ( \
- ".align 8;\n" \
- "sti %0; idle;\n" \
- ::"d" (irq_flags)); \
-} while (0)
+# define NOP_PAD_ANOMALY_05000244
#endif
+#define idle_with_irq_disabled() \
+ __asm__ __volatile__( \
+ NOP_PAD_ANOMALY_05000244 \
+ ".align 8;" \
+ "sti %0;" \
+ "idle;" \
+ : \
+ : "d" (irq_flags) \
+ )
+
#ifdef CONFIG_DEBUG_HWERR
-#define __save_and_cli(x) do { \
- __asm__ __volatile__ ( \
- "cli %0;\n\tsti %1;" \
- :"=&d"(x): "d" (0x3F)); \
-} while (0)
+# define __save_and_cli(x) \
+ __asm__ __volatile__( \
+ "cli %0;" \
+ "sti %1;" \
+ : "=&d" (x) \
+ : "d" (0x3F) \
+ )
#else
-#define __save_and_cli(x) do { \
- __asm__ __volatile__ ( \
- "cli %0;" \
- :"=&d"(x):); \
-} while (0)
+# define __save_and_cli(x) \
+ __asm__ __volatile__( \
+ "cli %0;" \
+ : "=&d" (x) \
+ )
#endif
-#define local_save_flags(x) asm volatile ("cli %0;" \
- "sti %0;" \
- :"=d"(x):);
+#define local_save_flags(x) \
+ __asm__ __volatile__( \
+ "cli %0;" \
+ "sti %0;" \
+ : "=d" (x) \
+ )
#ifdef CONFIG_DEBUG_HWERR
#define irqs_enabled_from_flags(x) (((x) & ~0x3f) != 0)
#define irqs_enabled_from_flags(x) ((x) != 0x1f)
#endif
-#define local_irq_restore(x) do { \
- if (irqs_enabled_from_flags(x)) \
- local_irq_enable (); \
-} while (0)
+#define local_irq_restore(x) \
+ do { \
+ if (irqs_enabled_from_flags(x)) \
+ local_irq_enable(); \
+ } while (0)
/* For spinlocks etc */
#define local_irq_save(x) __save_and_cli(x)
#define HUPCL 0002000
#define CLOCAL 0004000
#define CBAUDEX 0010000
+#define BOTHER 0010000
#define B57600 0010001
#define B115200 0010002
#define B230400 0010003
#define B3000000 0010015
#define B3500000 0010016
#define B4000000 0010017
-#define CIBAUD 002003600000 /* input baud rate (not used) */
+#define CIBAUD 002003600000 /* input baud rate */
#define CMSPAR 010000000000 /* mark or space (stick) parity */
#define CRTSCTS 020000000000 /* flow control */
+#define IBSHIFT 16 /* Shift from CBAUD to CIBAUD */
+
/* c_lflag bits */
#define ISIG 0000001
#define ICANON 0000002
copy_to_user((termio)->c_cc, (termios)->c_cc, NCC); \
})
-#define user_termios_to_kernel_termios(k, u) copy_from_user(k, u, sizeof(struct termios))
-#define kernel_termios_to_user_termios(u, k) copy_to_user(u, k, sizeof(struct termios))
+#define user_termios_to_kernel_termios(k, u) \
+ copy_from_user(k, u, sizeof(struct termios2))
+#define kernel_termios_to_user_termios(u, k) \
+ copy_to_user(u, k, sizeof(struct termios2))
+#define user_termios_to_kernel_termios_1(k, u) \
+ copy_from_user(k, u, sizeof(struct termios))
+#define kernel_termios_to_user_termios_1(u, k) \
+ copy_to_user(u, k, sizeof(struct termios))
#endif /* __KERNEL__ */
#ifndef _BLACKFIN_TRACE_
#define _BLACKFIN_TRACE_
+/* Normally, we use ON, but you can't turn on software expansion until
+ * interrupts subsystem is ready
+ */
+
+#define BFIN_TRACE_INIT ((CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION << 4) | 0x03)
+#ifdef CONFIG_DEBUG_BFIN_HWTRACE_EXPAND
+#define BFIN_TRACE_ON (BFIN_TRACE_INIT | (CONFIG_DEBUG_BFIN_HWTRACE_EXPAND << 2))
+#else
+#define BFIN_TRACE_ON (BFIN_TRACE_INIT)
+#endif
+
#ifndef __ASSEMBLY__
+extern unsigned long trace_buff_offset;
+extern unsigned long software_trace_buff[];
+
/* Trace Macros for C files */
+#ifdef CONFIG_DEBUG_BFIN_HWTRACE_ON
+
#define trace_buffer_save(x) \
- do { \
- (x) = bfin_read_TBUFCTL(); \
- bfin_write_TBUFCTL((x) & ~TBUFEN); \
- } while (0)
+ do { \
+ (x) = bfin_read_TBUFCTL(); \
+ bfin_write_TBUFCTL((x) & ~TBUFEN); \
+ } while (0)
#define trace_buffer_restore(x) \
- do { \
- bfin_write_TBUFCTL((x)); \
- } while (0)
+ do { \
+ bfin_write_TBUFCTL((x)); \
+ } while (0)
+#else /* DEBUG_BFIN_HWTRACE_ON */
+
+#define trace_buffer_save(x)
+#define trace_buffer_restore(x)
+#endif /* CONFIG_DEBUG_BFIN_HWTRACE_ON */
#else
/* Trace Macros for Assembly files */
+#ifdef CONFIG_DEBUG_BFIN_HWTRACE_ON
+
#define TRACE_BUFFER_START(preg, dreg) trace_buffer_start(preg, dreg)
#define TRACE_BUFFER_STOP(preg, dreg) trace_buffer_stop(preg, dreg)
dreg = 0x1; \
[preg] = dreg;
-#define trace_buffer_start(preg, dreg) \
+#define trace_buffer_start(preg, dreg) \
preg.L = LO(TBUFCTL); \
preg.H = HI(TBUFCTL); \
- dreg = 0x13; \
+ dreg = BFIN_TRACE_ON; \
+ [preg] = dreg;
+
+#define trace_buffer_init(preg, dreg) \
+ preg.L = LO(TBUFCTL); \
+ preg.H = HI(TBUFCTL); \
+ dreg = BFIN_TRACE_INIT; \
[preg] = dreg;
+#else /* CONFIG_DEBUG_BFIN_HWTRACE_ON */
+
+#define trace_buffer_stop(preg, dreg)
+#define trace_buffer_start(preg, dreg)
+#define trace_buffer_init(preg, dreg)
+
+#endif /* CONFIG_DEBUG_BFIN_HWTRACE_ON */
+
#ifdef CONFIG_DEBUG_BFIN_NO_KERN_HWTRACE
# define DEBUG_START_HWTRACE(preg, dreg) trace_buffer_start(preg, dreg)
# define DEBUG_STOP_HWTRACE(preg, dreg) trace_buffer_stop(preg, dreg)
projects / linux-2.6 / commitdiff