*
* This version supports shared IRQ's (only for PCI boards).
*
- * $Log: cyclades.c,v $
* Prevent users from opening non-existing Z ports.
*
* Revision 2.3.2.8 2000/07/06 18:14:16 ivan
* Driver now makes sure that the constant SERIAL_XMIT_SIZE is defined;
*
* Revision 2.3.2.2 1999/10/01 11:27:43 ivan
- * Fixed bug in cyz_poll that would make all ports but port 0
+ * Fixed bug in cyz_poll that would make all ports but port 0
* unable to transmit/receive data (Cyclades-Z only);
* Implemented logic to prevent the RX buffer from being stuck with data
* due to a driver / firmware race condition in interrupt op mode
* Revision 2.3.1.1 1999/07/15 16:45:53 ivan
* Removed CY_PROC conditional compilation;
* Implemented SMP-awareness for the driver;
- * Implemented a new ISA IRQ autoprobe that uses the irq_probe_[on|off]
+ * Implemented a new ISA IRQ autoprobe that uses the irq_probe_[on|off]
* functions;
* The driver now accepts memory addresses (maddr=0xMMMMM) and IRQs
* (irq=NN) as parameters (only for ISA boards);
- * Fixed bug in set_line_char that would prevent the Cyclades-Z
+ * Fixed bug in set_line_char that would prevent the Cyclades-Z
* ports from being configured at speeds above 115.2Kbps;
* Fixed bug in cy_set_termios that would prevent XON/XOFF flow control
* switching from working properly;
- * The driver now only prints IRQ info for the Cyclades-Z if it's
+ * The driver now only prints IRQ info for the Cyclades-Z if it's
* configured to work in interrupt mode;
*
* Revision 2.2.2.3 1999/06/28 11:13:29 ivan
* Added support for interrupt mode operation for the Z cards;
* Removed the driver inactivity control for the Z;
- * Added a missing MOD_DEC_USE_COUNT in the cy_open function for when
+ * Added a missing MOD_DEC_USE_COUNT in the cy_open function for when
* the Z firmware is not loaded yet;
- * Replaced the "manual" Z Tx flush buffer by a call to a FW command of
+ * Replaced the "manual" Z Tx flush buffer by a call to a FW command of
* same functionality;
- * Implemented workaround for IRQ setting loss on the PCI configuration
+ * Implemented workaround for IRQ setting loss on the PCI configuration
* registers after a PCI bridge EEPROM reload (affects PLX9060 only);
*
* Revision 2.2.2.2 1999/05/14 17:18:15 ivan
* BREAK implementation changed in order to make use of the 'break_ctl'
* TTY facility;
* Fixed typo in TTY structure field 'driver_name';
- * Included a PCI bridge reset and EEPROM reload in the board
+ * Included a PCI bridge reset and EEPROM reload in the board
* initialization code (for both Y and Z series).
*
* Revision 2.2.2.1 1999/04/08 16:17:43 ivan
- * Fixed a bug in cy_wait_until_sent that was preventing the port to be
+ * Fixed a bug in cy_wait_until_sent that was preventing the port to be
* closed properly after a SIGINT;
* Module usage counter scheme revisited;
* Added support to the upcoming Y PCI boards (i.e., support to additional
* PCI Device ID's).
- *
+ *
* Revision 2.2.1.10 1999/01/20 16:14:29 ivan
* Removed all unnecessary page-alignement operations in ioremap calls
* (ioremap is currently safe for these operations).
*
* Revision 2.2.1.9 1998/12/30 18:18:30 ivan
- * Changed access to PLX PCI bridge registers from I/O to MMIO, in
+ * Changed access to PLX PCI bridge registers from I/O to MMIO, in
* order to make PLX9050-based boards work with certain motherboards.
*
* Revision 2.2.1.8 1998/11/13 12:46:20 ivan
* Fixed Cyclom-4Yo hardware detection bug.
*
* Revision 2.2.1.4 1998/08/04 11:02:50 ivan
- * /proc/cyclades implementation with great collaboration of
+ * /proc/cyclades implementation with great collaboration of
* Marc Lewis <marc@blarg.net>;
* cyy_interrupt was changed to avoid occurrence of kernel oopses
* during PPP operation.
* General code review in order to comply with 2.1 kernel standards;
* data loss prevention for slow devices revisited (cy_wait_until_sent
* was created);
- * removed conditional compilation for new/old PCI structure support
+ * removed conditional compilation for new/old PCI structure support
* (now the driver only supports the new PCI structure).
*
* Revision 2.2.1.1 1998/03/19 16:43:12 ivan
* cleaned up the data loss fix;
* fixed XON/XOFF handling once more (Cyclades-Z);
* general review of the driver routines;
- * introduction of a mechanism to prevent data loss with slow
+ * introduction of a mechanism to prevent data loss with slow
* printers, by forcing a delay before closing the port.
*
* Revision 2.1.1.2 1998/02/17 16:50:00 ivan
* Code review for the module cleanup routine;
* fixed RTS and DTR status report for new CD1400's in get_modem_info;
* includes anonymous changes regarding signal_pending.
- *
+ *
* Revision 2.1 1997/11/01 17:42:41 ivan
* Changes in the driver to support Alpha systems (except 8Zo V_1);
* BREAK fix for the Cyclades-Z boards;
* driver inactivity control by FW implemented;
- * introduction of flag that allows driver to take advantage of
+ * introduction of flag that allows driver to take advantage of
* a special CD1400 feature related to HW flow control;
* added support for the CD1400 rev. J (Cyclom-Y boards);
* introduction of ioctls to:
* - adjust the polling interval (Cyclades-Z);
*
* Revision 1.36.4.33 1997/06/27 19:00:00 ivan
- * Fixes related to kernel version conditional
+ * Fixes related to kernel version conditional
* compilation.
- *
+ *
* Revision 1.36.4.32 1997/06/14 19:30:00 ivan
- * Compatibility issues between kernels 2.0.x and
+ * Compatibility issues between kernels 2.0.x and
* 2.1.x (mainly related to clear_bit function).
- *
+ *
* Revision 1.36.4.31 1997/06/03 15:30:00 ivan
- * Changes to define the memory window according to the
+ * Changes to define the memory window according to the
* board type.
- *
+ *
* Revision 1.36.4.30 1997/05/16 15:30:00 daniel
* Changes to support new cycladesZ boards.
*
#undef CY_PCI_DEBUG
/*
- * Include section
+ * Include section
*/
#include <linux/module.h>
#include <linux/errno.h>
#include <linux/firmware.h>
#include <asm/system.h>
-#include <asm/io.h>
+#include <linux/io.h>
#include <asm/irq.h>
-#include <asm/uaccess.h>
+#include <linux/uaccess.h>
#include <linux/kernel.h>
#include <linux/pci.h>
((readl(&((struct RUNTIME_9060 __iomem *) \
((card).ctl_addr))->init_ctrl) & (1<<17)) != 0)
-#define ISZLOADED(card) (((ZO_V1==readl(&((struct RUNTIME_9060 __iomem *) \
+#define ISZLOADED(card) (((ZO_V1 == readl(&((struct RUNTIME_9060 __iomem *) \
((card).ctl_addr))->mail_box_0)) || \
Z_FPGA_CHECK(card)) && \
- (ZFIRM_ID==readl(&((struct FIRM_ID __iomem *) \
+ (ZFIRM_ID == readl(&((struct FIRM_ID __iomem *) \
((card).base_addr+ID_ADDRESS))->signature)))
#ifndef SERIAL_XMIT_SIZE
/*
* The Cyclades driver implements HW flow control as any serial driver.
- * The cyclades_port structure member rflow and the vector rflow_thr
- * allows us to take advantage of a special feature in the CD1400 to avoid
- * data loss even when the system interrupt latency is too high. These flags
- * are to be used only with very special applications. Setting these flags
- * requires the use of a special cable (DTR and RTS reversed). In the new
- * CD1400-based boards (rev. 6.00 or later), there is no need for special
+ * The cyclades_port structure member rflow and the vector rflow_thr
+ * allows us to take advantage of a special feature in the CD1400 to avoid
+ * data loss even when the system interrupt latency is too high. These flags
+ * are to be used only with very special applications. Setting these flags
+ * requires the use of a special cable (DTR and RTS reversed). In the new
+ * CD1400-based boards (rev. 6.00 or later), there is no need for special
* cables.
*/
#ifdef CONFIG_PCI
static struct pci_device_id cy_pci_dev_id[] __devinitdata = {
- { PCI_DEVICE(PCI_VENDOR_ID_CYCLADES, PCI_DEVICE_ID_CYCLOM_Y_Lo) }, /* PCI < 1Mb */
- { PCI_DEVICE(PCI_VENDOR_ID_CYCLADES, PCI_DEVICE_ID_CYCLOM_Y_Hi) }, /* PCI > 1Mb */
- { PCI_DEVICE(PCI_VENDOR_ID_CYCLADES, PCI_DEVICE_ID_CYCLOM_4Y_Lo) }, /* 4Y PCI < 1Mb */
- { PCI_DEVICE(PCI_VENDOR_ID_CYCLADES, PCI_DEVICE_ID_CYCLOM_4Y_Hi) }, /* 4Y PCI > 1Mb */
- { PCI_DEVICE(PCI_VENDOR_ID_CYCLADES, PCI_DEVICE_ID_CYCLOM_8Y_Lo) }, /* 8Y PCI < 1Mb */
- { PCI_DEVICE(PCI_VENDOR_ID_CYCLADES, PCI_DEVICE_ID_CYCLOM_8Y_Hi) }, /* 8Y PCI > 1Mb */
- { PCI_DEVICE(PCI_VENDOR_ID_CYCLADES, PCI_DEVICE_ID_CYCLOM_Z_Lo) }, /* Z PCI < 1Mb */
- { PCI_DEVICE(PCI_VENDOR_ID_CYCLADES, PCI_DEVICE_ID_CYCLOM_Z_Hi) }, /* Z PCI > 1Mb */
+ /* PCI < 1Mb */
+ { PCI_DEVICE(PCI_VENDOR_ID_CYCLADES, PCI_DEVICE_ID_CYCLOM_Y_Lo) },
+ /* PCI > 1Mb */
+ { PCI_DEVICE(PCI_VENDOR_ID_CYCLADES, PCI_DEVICE_ID_CYCLOM_Y_Hi) },
+ /* 4Y PCI < 1Mb */
+ { PCI_DEVICE(PCI_VENDOR_ID_CYCLADES, PCI_DEVICE_ID_CYCLOM_4Y_Lo) },
+ /* 4Y PCI > 1Mb */
+ { PCI_DEVICE(PCI_VENDOR_ID_CYCLADES, PCI_DEVICE_ID_CYCLOM_4Y_Hi) },
+ /* 8Y PCI < 1Mb */
+ { PCI_DEVICE(PCI_VENDOR_ID_CYCLADES, PCI_DEVICE_ID_CYCLOM_8Y_Lo) },
+ /* 8Y PCI > 1Mb */
+ { PCI_DEVICE(PCI_VENDOR_ID_CYCLADES, PCI_DEVICE_ID_CYCLOM_8Y_Hi) },
+ /* Z PCI < 1Mb */
+ { PCI_DEVICE(PCI_VENDOR_ID_CYCLADES, PCI_DEVICE_ID_CYCLOM_Z_Lo) },
+ /* Z PCI > 1Mb */
+ { PCI_DEVICE(PCI_VENDOR_ID_CYCLADES, PCI_DEVICE_ID_CYCLOM_Z_Hi) },
{ } /* end of table */
};
MODULE_DEVICE_TABLE(pci, cy_pci_dev_id);
This function is only called from inside spinlock-protected code.
*/
-static int cyy_issue_cmd(void __iomem * base_addr, u_char cmd, int index)
+static int cyy_issue_cmd(void __iomem *base_addr, u_char cmd, int index)
{
unsigned int i;
/* Check to see that the previous command has completed */
for (i = 0; i < 100; i++) {
- if (readb(base_addr + (CyCCR << index)) == 0) {
+ if (readb(base_addr + (CyCCR << index)) == 0)
break;
- }
udelay(10L);
}
/* if the CCR never cleared, the previous command
#ifdef CONFIG_ISA
/* ISA interrupt detection code */
-static unsigned detect_isa_irq(void __iomem * address)
+static unsigned detect_isa_irq(void __iomem *address)
{
int irq;
unsigned long irqs, flags;
if (info->flags & ASYNC_SAK)
do_SAK(tty);
} else if (data & CyFRAME) {
- tty_insert_flip_char( tty,
+ tty_insert_flip_char(tty,
readb(base_addr + (CyRDSR <<
index)), TTY_FRAME);
info->icount.rx++;
if (unlikely(cinfo == NULL)) {
#ifdef CY_DEBUG_INTERRUPTS
- printk(KERN_DEBUG "cyy_interrupt: spurious interrupt %d\n",irq);
+ printk(KERN_DEBUG "cyy_interrupt: spurious interrupt %d\n",
+ irq);
#endif
return IRQ_NONE; /* spurious interrupt */
}
/***********************************************************/
/********* End of block of Cyclom-Y specific code **********/
-/******** Start of block of Cyclades-Z specific code *********/
+/******** Start of block of Cyclades-Z specific code *******/
/***********************************************************/
static int
cyz_fetch_msg(struct cyclades_card *cinfo,
- __u32 * channel, __u8 * cmd, __u32 * param)
+ __u32 *channel, __u8 *cmd, __u32 *param)
{
struct FIRM_ID __iomem *firm_id;
struct ZFW_CTRL __iomem *zfw_ctrl;
unsigned long loc_doorbell;
firm_id = cinfo->base_addr + ID_ADDRESS;
- if (!ISZLOADED(*cinfo)) {
+ if (!ISZLOADED(*cinfo))
return -1;
- }
zfw_ctrl = cinfo->base_addr + (readl(&firm_id->zfwctrl_addr) & 0xfffff);
board_ctrl = &zfw_ctrl->board_ctrl;
unsigned int index;
firm_id = cinfo->base_addr + ID_ADDRESS;
- if (!ISZLOADED(*cinfo)) {
+ if (!ISZLOADED(*cinfo))
return -1;
- }
+
zfw_ctrl = cinfo->base_addr + (readl(&firm_id->zfwctrl_addr) & 0xfffff);
board_ctrl = &zfw_ctrl->board_ctrl;
pci_doorbell =
&((struct RUNTIME_9060 __iomem *)(cinfo->ctl_addr))->pci_doorbell;
while ((readl(pci_doorbell) & 0xff) != 0) {
- if (index++ == 1000) {
+ if (index++ == 1000)
return (int)(readl(pci_doorbell) & 0xff);
- }
udelay(50L);
}
cy_writel(&board_ctrl->hcmd_channel, channel);
while (len--) {
data = readb(cinfo->base_addr + rx_bufaddr +
new_rx_get);
- new_rx_get = (new_rx_get + 1)& (rx_bufsize - 1);
+ new_rx_get = (new_rx_get + 1) &
+ (rx_bufsize - 1);
tty_insert_flip_char(tty, data, TTY_NORMAL);
info->idle_stats.recv_bytes++;
info->icount.rx++;
special_count = 0;
delta_count = 0;
info = &cinfo->ports[channel];
- if ((tty = info->tty) == NULL)
+ tty = info->tty;
+ if (tty == NULL)
continue;
ch_ctrl = &(zfw_ctrl->ch_ctrl[channel]);
if (unlikely(cinfo == NULL)) {
#ifdef CY_DEBUG_INTERRUPTS
- printk(KERN_DEBUG "cyz_interrupt: spurious interrupt %d\n",irq);
+ printk(KERN_DEBUG "cyz_interrupt: spurious interrupt %d\n",
+ irq);
#endif
return IRQ_NONE; /* spurious interrupt */
}
}
if (!info->type) {
- if (info->tty) {
+ if (info->tty)
set_bit(TTY_IO_ERROR, &info->tty->flags);
- }
free_page(page);
goto errout;
}
readb(base_addr + (CySRER << index)) | CyRxData);
info->flags |= ASYNC_INITIALIZED;
- if (info->tty) {
+ if (info->tty)
clear_bit(TTY_IO_ERROR, &info->tty->flags);
- }
info->xmit_cnt = info->xmit_head = info->xmit_tail = 0;
info->breakon = info->breakoff = 0;
memset((char *)&info->idle_stats, 0, sizeof(info->idle_stats));
base_addr = card->base_addr;
firm_id = base_addr + ID_ADDRESS;
- if (!ISZLOADED(*card)) {
+ if (!ISZLOADED(*card))
return -ENODEV;
- }
zfw_ctrl = card->base_addr +
(readl(&firm_id->zfwctrl_addr) & 0xfffff);
/* enable send, recv, modem !!! */
info->flags |= ASYNC_INITIALIZED;
- if (info->tty) {
+ if (info->tty)
clear_bit(TTY_IO_ERROR, &info->tty->flags);
- }
info->xmit_cnt = info->xmit_head = info->xmit_tail = 0;
info->breakon = info->breakoff = 0;
memset((char *)&info->idle_stats, 0, sizeof(info->idle_stats));
void __iomem *base_addr;
int chip, channel, index;
- if (!(info->flags & ASYNC_INITIALIZED)) {
+ if (!(info->flags & ASYNC_INITIALIZED))
return;
- }
card = info->card;
channel = info->line - card->first_line;
/* it may be appropriate to clear _XMIT at
some later date (after testing)!!! */
- if (info->tty) {
+ if (info->tty)
set_bit(TTY_IO_ERROR, &info->tty->flags);
- }
info->flags &= ~ASYNC_INITIALIZED;
spin_unlock_irqrestore(&card->card_lock, flags);
} else {
#endif
firm_id = base_addr + ID_ADDRESS;
- if (!ISZLOADED(*card)) {
+ if (!ISZLOADED(*card))
return;
- }
zfw_ctrl = card->base_addr +
(readl(&firm_id->zfwctrl_addr) & 0xfffff);
#endif
}
- if (info->tty) {
+ if (info->tty)
set_bit(TTY_IO_ERROR, &info->tty->flags);
- }
info->flags &= ~ASYNC_INITIALIZED;
spin_unlock_irqrestore(&card->card_lock, flags);
* If non-blocking mode is set, then make the check up front
* and then exit.
*/
- if ((filp->f_flags & O_NONBLOCK) || (tty->flags & (1 << TTY_IO_ERROR))) {
+ if ((filp->f_flags & O_NONBLOCK) ||
+ (tty->flags & (1 << TTY_IO_ERROR))) {
info->flags |= ASYNC_NORMAL_ACTIVE;
return 0;
}
return -EINVAL;
}
- zfw_ctrl = base_addr + (readl(&firm_id->zfwctrl_addr)& 0xfffff);
+ zfw_ctrl = base_addr + (readl(&firm_id->zfwctrl_addr)
+ & 0xfffff);
board_ctrl = &zfw_ctrl->board_ctrl;
ch_ctrl = zfw_ctrl->ch_ctrl;
int retval;
line = tty->index;
- if ((tty->index < 0) || (NR_PORTS <= line)) {
+ if (tty->index < 0 || NR_PORTS <= line)
return -ENODEV;
- }
+
for (i = 0; i < NR_CARDS; i++)
if (line < cy_card[i].first_line + cy_card[i].nports &&
line >= cy_card[i].first_line)
if (i >= NR_CARDS)
return -ENODEV;
info = &cy_card[i].ports[line - cy_card[i].first_line];
- if (info->line < 0) {
+ if (info->line < 0)
return -ENODEV;
- }
/* If the card's firmware hasn't been loaded,
treat it as absent from the system. This
#endif
tty->driver_data = info;
info->tty = tty;
- if (serial_paranoia_check(info, tty->name, "cy_open")) {
+ if (serial_paranoia_check(info, tty->name, "cy_open"))
return -ENODEV;
- }
+
#ifdef CY_DEBUG_OPEN
printk(KERN_DEBUG "cyc:cy_open ttyC%d, count = %d\n", info->line,
info->count);
* Start up serial port
*/
retval = startup(info);
- if (retval) {
+ if (retval)
return retval;
- }
retval = block_til_ready(tty, filp, info);
if (retval) {
printk(KERN_DEBUG "cyc:cy_close ttyC%d\n", info->line);
#endif
- if (!info || serial_paranoia_check(info, tty->name, "cy_close")) {
+ if (!info || serial_paranoia_check(info, tty->name, "cy_close"))
return;
- }
card = info->card;
*/
tty->closing = 1;
spin_unlock_irqrestore(&card->card_lock, flags);
- if (info->closing_wait != CY_CLOSING_WAIT_NONE) {
+ if (info->closing_wait != CY_CLOSING_WAIT_NONE)
tty_wait_until_sent(tty, info->closing_wait);
- }
+
spin_lock_irqsave(&card->card_lock, flags);
if (!IS_CYC_Z(*card)) {
cy_writeb(base_addr + (CySRER << index),
readb(base_addr + (CySRER << index)) & ~CyRxData);
if (info->flags & ASYNC_INITIALIZED) {
- /* Waiting for on-board buffers to be empty before closing
- the port */
+ /* Waiting for on-board buffers to be empty before
+ closing the port */
spin_unlock_irqrestore(&card->card_lock, flags);
cy_wait_until_sent(tty, info->timeout);
spin_lock_irqsave(&card->card_lock, flags);
}
} else {
#ifdef Z_WAKE
- /* Waiting for on-board buffers to be empty before closing the port */
+ /* Waiting for on-board buffers to be empty before closing
+ the port */
void __iomem *base_addr = card->base_addr;
struct FIRM_ID __iomem *firm_id = base_addr + ID_ADDRESS;
struct ZFW_CTRL __iomem *zfw_ctrl =
printk(KERN_DEBUG "cyc:cy_write ttyC%d\n", info->line);
#endif
- if (serial_paranoia_check(info, tty->name, "cy_write")) {
+ if (serial_paranoia_check(info, tty->name, "cy_write"))
return 0;
- }
if (!info->xmit_buf)
return 0;
info->idle_stats.xmit_bytes += ret;
info->idle_stats.xmit_idle = jiffies;
- if (info->xmit_cnt && !tty->stopped && !tty->hw_stopped) {
+ if (info->xmit_cnt && !tty->stopped && !tty->hw_stopped)
start_xmit(info);
- }
+
return ret;
} /* cy_write */
/*
* This routine is called by the kernel after it has written a
- * series of characters to the tty device using put_char().
+ * series of characters to the tty device using put_char().
*/
static void cy_flush_chars(struct tty_struct *tty)
{
int baud, baud_rate = 0;
int i;
- if (!info->tty || !info->tty->termios) {
+ if (!info->tty || !info->tty->termios)
return;
- }
- if (info->line == -1) {
+
+ if (info->line == -1)
return;
- }
+
cflag = info->tty->termios->c_cflag;
iflag = info->tty->termios->c_iflag;
}
/* find the baud index */
for (i = 0; i < 20; i++) {
- if (baud == baud_table[i]) {
+ if (baud == baud_table[i])
break;
- }
}
- if (i == 20) {
+ if (i == 20)
i = 19; /* CD1400_MAX_SPEED */
- }
if (baud == 38400 && (info->flags & ASYNC_SPD_MASK) ==
ASYNC_SPD_CUST) {
info->cor1 = Cy_8_BITS;
break;
}
- if (cflag & CSTOPB) {
+ if (cflag & CSTOPB)
info->cor1 |= Cy_2_STOP;
- }
+
if (cflag & PARENB) {
- if (cflag & PARODD) {
+ if (cflag & PARODD)
info->cor1 |= CyPARITY_O;
- } else {
+ else
info->cor1 |= CyPARITY_E;
- }
- } else {
+ } else
info->cor1 |= CyPARITY_NONE;
- }
/* CTS flow control flag */
if (cflag & CRTSCTS) {
cyy_issue_cmd(base_addr, CyCOR_CHANGE | CyCOR1ch | CyCOR2ch |
CyCOR3ch, index);
- cy_writeb(base_addr + (CyCAR << index), (u_char) channel); /* !!! Is this needed? */
+ /* !!! Is this needed? */
+ cy_writeb(base_addr + (CyCAR << index), (u_char) channel);
cy_writeb(base_addr + (CyRTPR << index),
(info->default_timeout ? info->default_timeout : 0x02));
/* 10ms rx timeout */
#endif
}
- if (info->tty) {
+ if (info->tty)
clear_bit(TTY_IO_ERROR, &info->tty->flags);
- }
spin_unlock_irqrestore(&card->card_lock, flags);
} else {
int retval;
firm_id = card->base_addr + ID_ADDRESS;
- if (!ISZLOADED(*card)) {
+ if (!ISZLOADED(*card))
return;
- }
zfw_ctrl = card->base_addr +
(readl(&firm_id->zfwctrl_addr) & 0xfffff);
readl(&ch_ctrl->comm_data_l) | C_DL_1STOP);
}
if (cflag & PARENB) {
- if (cflag & PARODD) {
+ if (cflag & PARODD)
cy_writel(&ch_ctrl->comm_parity, C_PR_ODD);
- } else {
+ else
cy_writel(&ch_ctrl->comm_parity, C_PR_EVEN);
- }
- } else {
+ } else
cy_writel(&ch_ctrl->comm_parity, C_PR_NONE);
- }
/* CTS flow control flag */
if (cflag & CRTSCTS) {
}
/* CD sensitivity */
- if (cflag & CLOCAL) {
+ if (cflag & CLOCAL)
info->flags &= ~ASYNC_CHECK_CD;
- } else {
+ else
info->flags |= ASYNC_CHECK_CD;
- }
if (baud == 0) { /* baud rate is zero, turn off line */
cy_writel(&ch_ctrl->rs_control,
#endif
}
- retval = cyz_issue_cmd(card, channel, C_CM_IOCTLM,0L);
+ retval = cyz_issue_cmd(card, channel, C_CM_IOCTLM, 0L);
if (retval != 0) {
printk(KERN_ERR "cyc:set_line_char(2) retval on ttyC%d "
"was %x\n", info->line, retval);
}
- if (info->tty) {
+ if (info->tty)
clear_bit(TTY_IO_ERROR, &info->tty->flags);
- }
}
} /* set_line_char */
static int
get_serial_info(struct cyclades_port *info,
- struct serial_struct __user * retinfo)
+ struct serial_struct __user *retinfo)
{
struct serial_struct tmp;
struct cyclades_card *cinfo = info->card;
static int
set_serial_info(struct cyclades_port *info,
- struct serial_struct __user * new_info)
+ struct serial_struct __user *new_info)
{
struct serial_struct new_serial;
struct cyclades_port old_info;
* transmit holding register is empty. This functionality
* allows an RS485 driver to be written in user space.
*/
-static int get_lsr_info(struct cyclades_port *info, unsigned int __user * value)
+static int get_lsr_info(struct cyclades_port *info, unsigned int __user *value)
{
struct cyclades_card *card;
int chip, channel, index;
spin_unlock_irqrestore(&card->card_lock, flags);
} /* cy_break */
-static int
-get_mon_info(struct cyclades_port *info, struct cyclades_monitor __user * mon)
+static int get_mon_info(struct cyclades_port *info,
+ struct cyclades_monitor __user *mon)
{
if (copy_to_user(mon, &info->mon, sizeof(struct cyclades_monitor)))
return 0;
} /* set_threshold */
-static int
-get_threshold(struct cyclades_port *info, unsigned long __user * value)
+static int get_threshold(struct cyclades_port *info,
+ unsigned long __user *value)
{
struct cyclades_card *card;
void __iomem *base_addr;
return 0;
} /* get_threshold */
-static int
-set_default_threshold(struct cyclades_port *info, unsigned long value)
+static int set_default_threshold(struct cyclades_port *info,
+ unsigned long value)
{
info->default_threshold = value & 0x0f;
return 0;
} /* set_default_threshold */
-static int
-get_default_threshold(struct cyclades_port *info, unsigned long __user * value)
+static int get_default_threshold(struct cyclades_port *info,
+ unsigned long __user *value)
{
return put_user(info->default_threshold, value);
} /* get_default_threshold */
return 0;
} /* set_timeout */
-static int get_timeout(struct cyclades_port *info, unsigned long __user * value)
+static int get_timeout(struct cyclades_port *info,
+ unsigned long __user *value)
{
struct cyclades_card *card;
void __iomem *base_addr;
return 0;
} /* set_default_timeout */
-static int
-get_default_timeout(struct cyclades_port *info, unsigned long __user * value)
+static int get_default_timeout(struct cyclades_port *info,
+ unsigned long __user *value)
{
return put_user(info->default_timeout, value);
} /* get_default_timeout */
break;
#endif /* CONFIG_CYZ_INTR */
case CYSETWAIT:
- info->closing_wait = (unsigned short)arg *HZ / 100;
+ info->closing_wait = (unsigned short)arg * HZ / 100;
ret_val = 0;
break;
case CYGETWAIT:
tty->ldisc.chars_in_buffer(tty), info->line);
#endif
- if (serial_paranoia_check(info, tty->name, "cy_throttle")) {
+ if (serial_paranoia_check(info, tty->name, "cy_throttle"))
return;
- }
card = info->card;
char buf[64];
printk(KERN_DEBUG "cyc:unthrottle %s: %ld...ttyC%d\n",
- tty_name(tty, buf), tty->ldisc.chars_in_buffer(tty),info->line);
+ tty_name(tty, buf), tty_chars_in_buffer(tty), info->line);
#endif
- if (serial_paranoia_check(info, tty->name, "cy_unthrottle")) {
+ if (serial_paranoia_check(info, tty->name, "cy_unthrottle"))
return;
- }
if (I_IXOFF(tty)) {
if (info->x_char)
base_addr = cinfo->base_addr + (cy_chip_offset[chip] << index);
spin_lock_irqsave(&cinfo->card_lock, flags);
- cy_writeb(base_addr + (CyCAR << index), (u_char) (channel & 0x0003)); /* index channel */
+ cy_writeb(base_addr + (CyCAR << index),
+ (u_char) (channel & 0x0003)); /* index channel */
cy_writeb(base_addr + (CySRER << index),
readb(base_addr + (CySRER << index)) | CyTxRdy);
spin_unlock_irqrestore(&cinfo->card_lock, flags);
info->cor3 = 0x08; /* _very_ small rcv threshold */
chip_number = (port - cinfo->first_line) / 4;
- if ((info->chip_rev = readb(cinfo->base_addr +
- (cy_chip_offset[chip_number] <<
- index) + (CyGFRCR << index))) >=
- CD1400_REV_J) {
+ info->chip_rev = readb(cinfo->base_addr +
+ (cy_chip_offset[chip_number] << index) +
+ (CyGFRCR << index));
+
+ if (info->chip_rev >= CD1400_REV_J) {
/* It is a CD1400 rev. J or later */
info->tbpr = baud_bpr_60[13]; /* Tx BPR */
info->tco = baud_co_60[13]; /* Tx CO */
/* Cy_ClrIntr is 0x1800 */
udelay(500L);
- for (chip_number = 0; chip_number < CyMAX_CHIPS_PER_CARD; chip_number++) {
+ for (chip_number = 0; chip_number < CyMAX_CHIPS_PER_CARD;
+ chip_number++) {
base_addr =
true_base_addr + (cy_chip_offset[chip_number] << index);
mdelay(1);
/* scan the address table probing for Cyclom-Y/ISA boards */
for (i = 0; i < NR_ISA_ADDRS; i++) {
unsigned int isa_address = cy_isa_addresses[i];
- if (isa_address == 0x0000) {
+ if (isa_address == 0x0000)
return nboard;
- }
/* probe for CD1400... */
cy_isa_address = ioremap(isa_address, CyISA_Ywin);
if (mailbox != 0) {
/* set window to last 512K of RAM */
cy_writel(&ctl_addr->loc_addr_base, WIN_RAM + RAM_SIZE);
- //sleep(1);
for (tmp = base_addr; tmp < base_addr + RAM_SIZE; tmp++)
cy_writeb(tmp, 255);
/* set window to beginning of RAM */
cy_writel(&ctl_addr->loc_addr_base, WIN_RAM);
- //sleep(1);
}
retval = __cyz_load_fw(fw, "Cyclom-Z", mailbox, base_addr, NULL);
del_timer_sync(&cyz_timerlist);
#endif /* CONFIG_CYZ_INTR */
- if ((e1 = tty_unregister_driver(cy_serial_driver)))
+ e1 = tty_unregister_driver(cy_serial_driver);
+ if (e1)
printk(KERN_ERR "failed to unregister Cyclades serial "
"driver(%d)\n", e1);
projects / linux-2.6 / commitdiff