- device_type : should be "network", "hldc", "uart", "transparent"
"bisync", "atm", or "serial".
- compatible : could be "ucc_geth" or "fsl_atm" and so on.
- - model : should be "UCC".
- - device-id : the ucc number(1-8), corresponding to UCCx in UM.
+ - cell-index : the ucc number(1-8), corresponding to UCCx in UM.
- reg : Offset and length of the register set for the device
- interrupts : <a b> where a is the interrupt number and b is a
field that represents an encoding of the sense and level
ucc@2000 {
device_type = "network";
compatible = "ucc_geth";
- model = "UCC";
- device-id = <1>;
+ cell-index = <1>;
reg = <2000 200>;
interrupts = <a0 0>;
interrupt-parent = <700>;
config 4xx_SOC
bool
+config FSL_LBC
+ bool
+ help
+ Freescale Localbus support
+
# Yes MCA RS/6000s exist but Linux-PPC does not currently support any
config MCA
bool
hex "CPM UART early debug transmit descriptor address"
depends on PPC_EARLY_DEBUG_CPM
default "0xfa202008" if PPC_EP88XC
- default "0xf0000008" if CPM2
+ default "0xf0001ff8" if CPM2
default "0xff002008" if CPM1
help
This specifies the address of the transmit descriptor
#include "types.h"
#include "io.h"
#include "ops.h"
+#include "page.h"
struct cpm_scc {
u32 gsmrl;
u16 tbase;
u8 rfcr;
u8 tfcr;
+ u16 mrblr;
+ u32 rstate;
+ u8 res1[4];
+ u16 rbptr;
+ u8 res2[6];
+ u32 tstate;
+ u8 res3[4];
+ u16 tbptr;
+ u8 res4[6];
+ u16 maxidl;
+ u16 idlc;
+ u16 brkln;
+ u16 brkec;
+ u16 brkcr;
+ u16 rmask;
+ u8 res5[4];
};
struct cpm_bd {
static struct cpm_param *param;
static struct cpm_smc *smc;
static struct cpm_scc *scc;
-struct cpm_bd *tbdf, *rbdf;
+static struct cpm_bd *tbdf, *rbdf;
static u32 cpm_cmd;
-static u8 *muram_start;
-static u32 muram_offset;
+static void *cbd_addr;
+static u32 cbd_offset;
static void (*do_cmd)(int op);
static void (*enable_port)(void);
out_8(¶m->rfcr, 0x10);
out_8(¶m->tfcr, 0x10);
-
- rbdf = (struct cpm_bd *)muram_start;
- rbdf->addr = (u8 *)(rbdf + 2);
+ out_be16(¶m->mrblr, 1);
+ out_be16(¶m->maxidl, 0);
+ out_be16(¶m->brkec, 0);
+ out_be16(¶m->brkln, 0);
+ out_be16(¶m->brkcr, 0);
+
+ rbdf = cbd_addr;
+ rbdf->addr = (u8 *)rbdf - 1;
rbdf->sc = 0xa000;
rbdf->len = 1;
tbdf = rbdf + 1;
- tbdf->addr = (u8 *)(rbdf + 2) + 1;
+ tbdf->addr = (u8 *)rbdf - 2;
tbdf->sc = 0x2000;
tbdf->len = 1;
sync();
- out_be16(¶m->rbase, muram_offset);
- out_be16(¶m->tbase, muram_offset + sizeof(struct cpm_bd));
+ out_be16(¶m->rbase, cbd_offset);
+ out_be16(¶m->tbase, cbd_offset + sizeof(struct cpm_bd));
do_cmd(CPM_CMD_INIT_RX_TX);
int cpm_console_init(void *devp, struct serial_console_data *scdp)
{
- void *reg_virt[2];
- int is_smc = 0, is_cpm2 = 0, n;
- unsigned long reg_phys;
+ void *vreg[2];
+ u32 reg[2];
+ int is_smc = 0, is_cpm2 = 0;
void *parent, *muram;
+ void *muram_addr;
+ unsigned long muram_offset, muram_size;
if (dt_is_compatible(devp, "fsl,cpm1-smc-uart")) {
is_smc = 1;
else
do_cmd = cpm1_cmd;
- n = getprop(devp, "fsl,cpm-command", &cpm_cmd, 4);
- if (n < 4)
+ if (getprop(devp, "fsl,cpm-command", &cpm_cmd, 4) < 4)
return -1;
- n = getprop(devp, "virtual-reg", reg_virt, sizeof(reg_virt));
- if (n < (int)sizeof(reg_virt)) {
- for (n = 0; n < 2; n++) {
- if (!dt_xlate_reg(devp, n, ®_phys, NULL))
- return -1;
-
- reg_virt[n] = (void *)reg_phys;
- }
- }
+ if (dt_get_virtual_reg(devp, vreg, 2) < 2)
+ return -1;
if (is_smc)
- smc = reg_virt[0];
+ smc = vreg[0];
else
- scc = reg_virt[0];
+ scc = vreg[0];
- param = reg_virt[1];
+ param = vreg[1];
parent = get_parent(devp);
if (!parent)
return -1;
- n = getprop(parent, "virtual-reg", reg_virt, sizeof(reg_virt));
- if (n < (int)sizeof(reg_virt)) {
- if (!dt_xlate_reg(parent, 0, ®_phys, NULL))
- return -1;
-
- reg_virt[0] = (void *)reg_phys;
- }
-
- cpcr = reg_virt[0];
+ if (dt_get_virtual_reg(parent, &cpcr, 1) < 1)
+ return -1;
muram = finddevice("/soc/cpm/muram/data");
if (!muram)
return -1;
/* For bootwrapper-compatible device trees, we assume that the first
- * entry has at least 18 bytes, and that #address-cells/#data-cells
+ * entry has at least 128 bytes, and that #address-cells/#data-cells
* is one for both parent and child.
*/
- n = getprop(muram, "virtual-reg", reg_virt, sizeof(reg_virt));
- if (n < (int)sizeof(reg_virt)) {
- if (!dt_xlate_reg(muram, 0, ®_phys, NULL))
- return -1;
+ if (dt_get_virtual_reg(muram, &muram_addr, 1) < 1)
+ return -1;
- reg_virt[0] = (void *)reg_phys;
- }
+ if (getprop(muram, "reg", reg, 8) < 8)
+ return -1;
- muram_start = reg_virt[0];
+ muram_offset = reg[0];
+ muram_size = reg[1];
- n = getprop(muram, "reg", &muram_offset, 4);
- if (n < 4)
- return -1;
+ /* Store the buffer descriptors at the end of the first muram chunk.
+ * For SMC ports on CPM2-based platforms, relocate the parameter RAM
+ * just before the buffer descriptors.
+ */
+
+ cbd_offset = muram_offset + muram_size - 2 * sizeof(struct cpm_bd);
+
+ if (is_cpm2 && is_smc) {
+ u16 *smc_base = (u16 *)param;
+ u16 pram_offset;
+
+ pram_offset = cbd_offset - 64;
+ pram_offset = _ALIGN_DOWN(pram_offset, 64);
+
+ disable_port();
+ out_be16(smc_base, pram_offset);
+ param = muram_addr - muram_offset + pram_offset;
+ }
+
+ cbd_addr = muram_addr - muram_offset + cbd_offset;
scdp->open = cpm_serial_open;
scdp->putc = cpm_serial_putc;
u8 *soc_regs;
int i, len;
void *node, *parent_node;
- u32 naddr, nsize, mem_log2;
+ u32 naddr, nsize, mem_pow2, mem_mask;
node = finddevice("/pci");
if (!node || !dt_is_compatible(node, "fsl,pq2-pci"))
soc_regs = (u8 *)fsl_get_immr();
if (!soc_regs)
- goto err;
+ goto unhandled;
dt_get_reg_format(node, &naddr, &nsize);
if (naddr != 3 || nsize != 2)
dt_get_reg_format(parent_node, &naddr, &nsize);
if (naddr != 1 || nsize != 1)
- goto err;
+ goto unhandled;
len = getprop(node, "ranges", pci_ranges_buf,
sizeof(pci_ranges_buf));
}
if (!mem || !mmio || !io)
- goto err;
+ goto unhandled;
+ if (mem->size[1] != mmio->size[1])
+ goto unhandled;
+ if (mem->size[1] & (mem->size[1] - 1))
+ goto unhandled;
+ if (io->size[1] & (io->size[1] - 1))
+ goto unhandled;
if (mem->phys_addr + mem->size[1] == mmio->phys_addr)
mem_base = mem;
else if (mmio->phys_addr + mmio->size[1] == mem->phys_addr)
mem_base = mmio;
else
- goto err;
+ goto unhandled;
out_be32(&pci_regs[1][0], mem_base->phys_addr | 1);
out_be32(&pci_regs[2][0], ~(mem->size[1] + mmio->size[1] - 1));
out_le32(&pci_regs[0][58], 0);
out_le32(&pci_regs[0][60], 0);
- mem_log2 = 1 << (__ilog2_u32(bd.bi_memsize - 1) + 1);
- out_le32(&pci_regs[0][62], 0xa0000000 | ~((1 << (mem_log2 - 12)) - 1));
+ mem_pow2 = 1 << (__ilog2_u32(bd.bi_memsize - 1) + 1);
+ mem_mask = ~(mem_pow2 - 1) >> 12;
+ out_le32(&pci_regs[0][62], 0xa0000000 | mem_mask);
/* If PCI is disabled, drive RST high to enable. */
if (!(in_le32(&pci_regs[0][32]) & 1)) {
return;
err:
- printf("Bad PCI node\r\n");
+ printf("Bad PCI node -- using existing firmware setup.\r\n");
+ return;
+
+unhandled:
+ printf("Unsupported PCI node -- using existing firmware setup.\r\n");
}
static void pq2_platform_fixups(void)
return 0;
}
+
+int dt_get_virtual_reg(void *node, void **addr, int nres)
+{
+ unsigned long xaddr;
+ int n;
+
+ n = getprop(node, "virtual-reg", addr, nres * 4);
+ if (n > 0)
+ return n / 4;
+
+ for (n = 0; n < nres; n++) {
+ if (!dt_xlate_reg(node, n, &xaddr, NULL))
+ break;
+
+ addr[n] = (void *)xaddr;
+ }
+
+ return n;
+}
+
data@0 {
compatible = "fsl,cpm-muram-data";
- reg = <0 0x1100 0x1140
- 0xec0 0x9800 0x800>;
+ reg = <0 0x2000 0x9800 0x800>;
};
};
device_type = "serial";
compatible = "fsl,mpc8248-smc-uart",
"fsl,cpm2-smc-uart";
- reg = <0x11a80 0x20 0x1100 0x40>;
+ reg = <0x11a80 0x20 0x87fc 2>;
interrupts = <4 8>;
interrupt-parent = <&PIC>;
fsl,cpm-brg = <7>;
* EP88xC Device Tree Source
*
* Copyright 2006 MontaVista Software, Inc.
- * Copyright 2007 Freescale Semiconductor, Inc.
+ * Copyright 2007,2008 Freescale Semiconductor, Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* option) any later version.
*/
+/dts-v1/;
/ {
model = "EP88xC";
PowerPC,885@0 {
device_type = "cpu";
- reg = <0>;
- d-cache-line-size = <d#16>;
- i-cache-line-size = <d#16>;
- d-cache-size = <d#8192>;
- i-cache-size = <d#8192>;
+ reg = <0x0>;
+ d-cache-line-size = <16>;
+ i-cache-line-size = <16>;
+ d-cache-size = <8192>;
+ i-cache-size = <8192>;
timebase-frequency = <0>;
bus-frequency = <0>;
clock-frequency = <0>;
- interrupts = <f 2>; // decrementer interrupt
+ interrupts = <15 2>; // decrementer interrupt
interrupt-parent = <&PIC>;
};
};
memory {
device_type = "memory";
- reg = <0 0>;
+ reg = <0x0 0x0>;
};
localbus@fa200100 {
compatible = "fsl,mpc885-localbus", "fsl,pq1-localbus";
#address-cells = <2>;
#size-cells = <1>;
- reg = <fa200100 40>;
+ reg = <0xfa200100 0x40>;
ranges = <
- 0 0 fc000000 04000000
- 3 0 fa000000 01000000
+ 0x0 0x0 0xfc000000 0x4000000
+ 0x3 0x0 0xfa000000 0x1000000
>;
flash@0,2000000 {
compatible = "cfi-flash";
- reg = <0 2000000 2000000>;
+ reg = <0x0 0x2000000 0x2000000>;
bank-width = <4>;
device-width = <2>;
};
board-control@3,400000 {
- reg = <3 400000 10>;
+ reg = <0x3 0x400000 0x10>;
compatible = "fsl,ep88xc-bcsr";
};
};
#address-cells = <1>;
#size-cells = <1>;
device_type = "soc";
- ranges = <0 fa200000 00004000>;
+ ranges = <0x0 0xfa200000 0x4000>;
bus-frequency = <0>;
// Temporary -- will go away once kernel uses ranges for get_immrbase().
- reg = <fa200000 4000>;
+ reg = <0xfa200000 0x4000>;
mdio@e00 {
compatible = "fsl,mpc885-fec-mdio", "fsl,pq1-fec-mdio";
- reg = <e00 188>;
+ reg = <0xe00 0x188>;
#address-cells = <1>;
#size-cells = <0>;
PHY0: ethernet-phy@0 {
- reg = <0>;
+ reg = <0x0>;
device_type = "ethernet-phy";
};
PHY1: ethernet-phy@1 {
- reg = <1>;
+ reg = <0x1>;
device_type = "ethernet-phy";
};
};
device_type = "network";
compatible = "fsl,mpc885-fec-enet",
"fsl,pq1-fec-enet";
- reg = <e00 188>;
+ reg = <0xe00 0x188>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <3 1>;
interrupt-parent = <&PIC>;
device_type = "network";
compatible = "fsl,mpc885-fec-enet",
"fsl,pq1-fec-enet";
- reg = <1e00 188>;
+ reg = <0x1e00 0x188>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <7 1>;
interrupt-parent = <&PIC>;
PIC: interrupt-controller@0 {
interrupt-controller;
#interrupt-cells = <2>;
- reg = <0 24>;
+ reg = <0x0 0x24>;
compatible = "fsl,mpc885-pic", "fsl,pq1-pic";
};
#size-cells = <2>;
compatible = "fsl,pq-pcmcia";
device_type = "pcmcia";
- reg = <80 80>;
+ reg = <0x80 0x80>;
interrupt-parent = <&PIC>;
- interrupts = <d 1>;
+ interrupts = <13 1>;
};
cpm@9c0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "fsl,mpc885-cpm", "fsl,cpm1";
- command-proc = <9c0>;
+ command-proc = <0x9c0>;
interrupts = <0>; // cpm error interrupt
interrupt-parent = <&CPM_PIC>;
- reg = <9c0 40>;
+ reg = <0x9c0 0x40>;
ranges;
muram@2000 {
#address-cells = <1>;
#size-cells = <1>;
- ranges = <0 2000 2000>;
+ ranges = <0x0 0x2000 0x2000>;
data@0 {
compatible = "fsl,cpm-muram-data";
- reg = <0 1c00>;
+ reg = <0x0 0x1c00>;
};
};
compatible = "fsl,mpc885-brg",
"fsl,cpm1-brg",
"fsl,cpm-brg";
- reg = <9f0 10>;
+ reg = <0x9f0 0x10>;
};
CPM_PIC: interrupt-controller@930 {
#interrupt-cells = <1>;
interrupts = <5 2 0 2>;
interrupt-parent = <&PIC>;
- reg = <930 20>;
+ reg = <0x930 0x20>;
compatible = "fsl,mpc885-cpm-pic",
"fsl,cpm1-pic";
};
device_type = "serial";
compatible = "fsl,mpc885-smc-uart",
"fsl,cpm1-smc-uart";
- reg = <a80 10 3e80 40>;
+ reg = <0xa80 0x10 0x3e80 0x40>;
interrupts = <4>;
interrupt-parent = <&CPM_PIC>;
fsl,cpm-brg = <1>;
- fsl,cpm-command = <0090>;
+ fsl,cpm-command = <0x90>;
linux,planetcore-label = "SMC1";
};
device_type = "serial";
compatible = "fsl,mpc885-scc-uart",
"fsl,cpm1-scc-uart";
- reg = <a20 20 3d00 80>;
- interrupts = <1d>;
+ reg = <0xa20 0x20 0x3d00 0x80>;
+ interrupts = <29>;
interrupt-parent = <&CPM_PIC>;
fsl,cpm-brg = <2>;
- fsl,cpm-command = <0040>;
+ fsl,cpm-command = <0x40>;
linux,planetcore-label = "SCC2";
};
#size-cells = <0>;
compatible = "fsl,mpc885-usb",
"fsl,cpm1-usb";
- reg = <a00 18 1c00 80>;
+ reg = <0xa00 0x18 0x1c00 0x80>;
interrupt-parent = <&CPM_PIC>;
- interrupts = <1e>;
+ interrupts = <30>;
fsl,cpm-command = <0000>;
};
};
* Based on sandpoint.dts
*
* 2006 (c) G. Liakhovetski <g.liakhovetski@gmx.de>
+ * Copyright 2008 Freescale Semiconductor, Inc.
*
* This file is licensed under
* the terms of the GNU General Public License version 2. This program
*/
+/dts-v1/;
+
/ {
model = "KuroboxHD";
compatible = "linkstation";
PowerPC,603e { /* Really 8241 */
device_type = "cpu";
- reg = <0>;
- clock-frequency = <bebc200>; /* Fixed by bootloader */
- timebase-frequency = <1743000>; /* Fixed by bootloader */
+ reg = <0x0>;
+ clock-frequency = <200000000>; /* Fixed by bootloader */
+ timebase-frequency = <24391680>; /* Fixed by bootloader */
bus-frequency = <0>; /* Fixed by bootloader */
/* Following required by dtc but not used */
- i-cache-size = <4000>;
- d-cache-size = <4000>;
+ i-cache-size = <0x4000>;
+ d-cache-size = <0x4000>;
};
};
memory {
device_type = "memory";
- reg = <00000000 04000000>;
+ reg = <0x0 0x4000000>;
};
soc10x { /* AFAICT need to make soc for 8245's uarts to be defined */
device_type = "soc";
compatible = "mpc10x";
store-gathering = <0>; /* 0 == off, !0 == on */
- reg = <80000000 00100000>;
- ranges = <80000000 80000000 70000000 /* pci mem space */
- fc000000 fc000000 00100000 /* EUMB */
- fe000000 fe000000 00c00000 /* pci i/o space */
- fec00000 fec00000 00300000 /* pci cfg regs */
- fef00000 fef00000 00100000>; /* pci iack */
+ reg = <0x80000000 0x100000>;
+ ranges = <0x80000000 0x80000000 0x70000000 /* pci mem space */
+ 0xfc000000 0xfc000000 0x100000 /* EUMB */
+ 0xfe000000 0xfe000000 0xc00000 /* pci i/o space */
+ 0xfec00000 0xfec00000 0x300000 /* pci cfg regs */
+ 0xfef00000 0xfef00000 0x100000>; /* pci iack */
i2c@80003000 {
#address-cells = <1>;
#size-cells = <0>;
cell-index = <0>;
compatible = "fsl-i2c";
- reg = <80003000 1000>;
+ reg = <0x80003000 0x1000>;
interrupts = <5 2>;
interrupt-parent = <&mpic>;
rtc@32 {
device_type = "rtc";
compatible = "ricoh,rs5c372a";
- reg = <32>;
+ reg = <0x32>;
};
};
cell-index = <0>;
device_type = "serial";
compatible = "ns16550";
- reg = <80004500 8>;
- clock-frequency = <5d08d88>;
- current-speed = <2580>;
+ reg = <0x80004500 0x8>;
+ clock-frequency = <97553800>;
+ current-speed = <9600>;
interrupts = <9 0>;
interrupt-parent = <&mpic>;
};
cell-index = <1>;
device_type = "serial";
compatible = "ns16550";
- reg = <80004600 8>;
- clock-frequency = <5d08d88>;
- current-speed = <e100>;
- interrupts = <a 0>;
+ reg = <0x80004600 0x8>;
+ clock-frequency = <97553800>;
+ current-speed = <57600>;
+ interrupts = <10 0>;
interrupt-parent = <&mpic>;
};
device_type = "open-pic";
compatible = "chrp,open-pic";
interrupt-controller;
- reg = <80040000 40000>;
+ reg = <0x80040000 0x40000>;
};
pci0: pci@fec00000 {
#interrupt-cells = <1>;
device_type = "pci";
compatible = "mpc10x-pci";
- reg = <fec00000 400000>;
- ranges = <01000000 0 0 fe000000 0 00c00000
- 02000000 0 80000000 80000000 0 70000000>;
- bus-range = <0 ff>;
- clock-frequency = <7f28155>;
+ reg = <0xfec00000 0x400000>;
+ ranges = <0x1000000 0x0 0x0 0xfe000000 0x0 0xc00000
+ 0x2000000 0x0 0x80000000 0x80000000 0x0 0x70000000>;
+ bus-range = <0 255>;
+ clock-frequency = <133333333>;
interrupt-parent = <&mpic>;
- interrupt-map-mask = <f800 0 0 7>;
+ interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
interrupt-map = <
/* IDSEL 11 - IRQ0 ETH */
- 5800 0 0 1 &mpic 0 1
- 5800 0 0 2 &mpic 1 1
- 5800 0 0 3 &mpic 2 1
- 5800 0 0 4 &mpic 3 1
+ 0x5800 0x0 0x0 0x1 &mpic 0x0 0x1
+ 0x5800 0x0 0x0 0x2 &mpic 0x1 0x1
+ 0x5800 0x0 0x0 0x3 &mpic 0x2 0x1
+ 0x5800 0x0 0x0 0x4 &mpic 0x3 0x1
/* IDSEL 12 - IRQ1 IDE0 */
- 6000 0 0 1 &mpic 1 1
- 6000 0 0 2 &mpic 2 1
- 6000 0 0 3 &mpic 3 1
- 6000 0 0 4 &mpic 0 1
+ 0x6000 0x0 0x0 0x1 &mpic 0x1 0x1
+ 0x6000 0x0 0x0 0x2 &mpic 0x2 0x1
+ 0x6000 0x0 0x0 0x3 &mpic 0x3 0x1
+ 0x6000 0x0 0x0 0x4 &mpic 0x0 0x1
/* IDSEL 14 - IRQ3 USB2.0 */
- 7000 0 0 1 &mpic 3 1
- 7000 0 0 2 &mpic 3 1
- 7000 0 0 3 &mpic 3 1
- 7000 0 0 4 &mpic 3 1
+ 0x7000 0x0 0x0 0x1 &mpic 0x3 0x1
+ 0x7000 0x0 0x0 0x2 &mpic 0x3 0x1
+ 0x7000 0x0 0x0 0x3 &mpic 0x3 0x1
+ 0x7000 0x0 0x0 0x4 &mpic 0x3 0x1
>;
};
};
* Based on sandpoint.dts
*
* 2006 (c) G. Liakhovetski <g.liakhovetski@gmx.de>
+ * Copyright 2008 Freescale Semiconductor, Inc.
*
* This file is licensed under
* the terms of the GNU General Public License version 2. This program
*/
+/dts-v1/;
+
/ {
model = "KuroboxHG";
compatible = "linkstation";
PowerPC,603e { /* Really 8241 */
device_type = "cpu";
- reg = <0>;
- clock-frequency = <fdad680>; /* Fixed by bootloader */
- timebase-frequency = <1F04000>; /* Fixed by bootloader */
+ reg = <0x0>;
+ clock-frequency = <266000000>; /* Fixed by bootloader */
+ timebase-frequency = <32522240>; /* Fixed by bootloader */
bus-frequency = <0>; /* Fixed by bootloader */
/* Following required by dtc but not used */
- i-cache-size = <4000>;
- d-cache-size = <4000>;
+ i-cache-size = <0x4000>;
+ d-cache-size = <0x4000>;
};
};
memory {
device_type = "memory";
- reg = <00000000 08000000>;
+ reg = <0x0 0x8000000>;
};
soc10x { /* AFAICT need to make soc for 8245's uarts to be defined */
device_type = "soc";
compatible = "mpc10x";
store-gathering = <0>; /* 0 == off, !0 == on */
- reg = <80000000 00100000>;
- ranges = <80000000 80000000 70000000 /* pci mem space */
- fc000000 fc000000 00100000 /* EUMB */
- fe000000 fe000000 00c00000 /* pci i/o space */
- fec00000 fec00000 00300000 /* pci cfg regs */
- fef00000 fef00000 00100000>; /* pci iack */
+ reg = <0x80000000 0x100000>;
+ ranges = <0x80000000 0x80000000 0x70000000 /* pci mem space */
+ 0xfc000000 0xfc000000 0x100000 /* EUMB */
+ 0xfe000000 0xfe000000 0xc00000 /* pci i/o space */
+ 0xfec00000 0xfec00000 0x300000 /* pci cfg regs */
+ 0xfef00000 0xfef00000 0x100000>; /* pci iack */
i2c@80003000 {
#address-cells = <1>;
#size-cells = <0>;
cell-index = <0>;
compatible = "fsl-i2c";
- reg = <80003000 1000>;
+ reg = <0x80003000 0x1000>;
interrupts = <5 2>;
interrupt-parent = <&mpic>;
rtc@32 {
device_type = "rtc";
compatible = "ricoh,rs5c372a";
- reg = <32>;
+ reg = <0x32>;
};
};
cell-index = <0>;
device_type = "serial";
compatible = "ns16550";
- reg = <80004500 8>;
- clock-frequency = <7c044a8>;
- current-speed = <2580>;
+ reg = <0x80004500 0x8>;
+ clock-frequency = <130041000>;
+ current-speed = <9600>;
interrupts = <9 0>;
interrupt-parent = <&mpic>;
};
cell-index = <1>;
device_type = "serial";
compatible = "ns16550";
- reg = <80004600 8>;
- clock-frequency = <7c044a8>;
- current-speed = <e100>;
- interrupts = <a 0>;
+ reg = <0x80004600 0x8>;
+ clock-frequency = <130041000>;
+ current-speed = <57600>;
+ interrupts = <10 0>;
interrupt-parent = <&mpic>;
};
device_type = "open-pic";
compatible = "chrp,open-pic";
interrupt-controller;
- reg = <80040000 40000>;
+ reg = <0x80040000 0x40000>;
};
pci0: pci@fec00000 {
#interrupt-cells = <1>;
device_type = "pci";
compatible = "mpc10x-pci";
- reg = <fec00000 400000>;
- ranges = <01000000 0 0 fe000000 0 00c00000
- 02000000 0 80000000 80000000 0 70000000>;
- bus-range = <0 ff>;
- clock-frequency = <7f28155>;
+ reg = <0xfec00000 0x400000>;
+ ranges = <0x1000000 0x0 0x0 0xfe000000 0x0 0xc00000
+ 0x2000000 0x0 0x80000000 0x80000000 0x0 0x70000000>;
+ bus-range = <0 255>;
+ clock-frequency = <133333333>;
interrupt-parent = <&mpic>;
- interrupt-map-mask = <f800 0 0 7>;
+ interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
interrupt-map = <
/* IDSEL 11 - IRQ0 ETH */
- 5800 0 0 1 &mpic 0 1
- 5800 0 0 2 &mpic 1 1
- 5800 0 0 3 &mpic 2 1
- 5800 0 0 4 &mpic 3 1
+ 0x5800 0x0 0x0 0x1 &mpic 0x0 0x1
+ 0x5800 0x0 0x0 0x2 &mpic 0x1 0x1
+ 0x5800 0x0 0x0 0x3 &mpic 0x2 0x1
+ 0x5800 0x0 0x0 0x4 &mpic 0x3 0x1
/* IDSEL 12 - IRQ1 IDE0 */
- 6000 0 0 1 &mpic 1 1
- 6000 0 0 2 &mpic 2 1
- 6000 0 0 3 &mpic 3 1
- 6000 0 0 4 &mpic 0 1
+ 0x6000 0x0 0x0 0x1 &mpic 0x1 0x1
+ 0x6000 0x0 0x0 0x2 &mpic 0x2 0x1
+ 0x6000 0x0 0x0 0x3 &mpic 0x3 0x1
+ 0x6000 0x0 0x0 0x4 &mpic 0x0 0x1
/* IDSEL 14 - IRQ3 USB2.0 */
- 7000 0 0 1 &mpic 3 1
- 7000 0 0 2 &mpic 3 1
- 7000 0 0 3 &mpic 3 1
- 7000 0 0 4 &mpic 3 1
+ 0x7000 0x0 0x0 0x1 &mpic 0x3 0x1
+ 0x7000 0x0 0x0 0x2 &mpic 0x3 0x1
+ 0x7000 0x0 0x0 0x3 &mpic 0x3 0x1
+ 0x7000 0x0 0x0 0x4 &mpic 0x3 0x1
>;
};
};
/*
* MPC7448HPC2 (Taiga) board Device Tree Source
*
- * Copyright 2006 Freescale Semiconductor Inc.
+ * Copyright 2006, 2008 Freescale Semiconductor Inc.
* 2006 Roy Zang <Roy Zang at freescale.com>.
*
* This program is free software; you can redistribute it and/or modify it
* option) any later version.
*/
+/dts-v1/;
/ {
model = "mpc7448hpc2";
PowerPC,7448@0 {
device_type = "cpu";
- reg = <0>;
- d-cache-line-size = <20>; // 32 bytes
- i-cache-line-size = <20>; // 32 bytes
- d-cache-size = <8000>; // L1, 32K bytes
- i-cache-size = <8000>; // L1, 32K bytes
+ reg = <0x0>;
+ d-cache-line-size = <32>; // 32 bytes
+ i-cache-line-size = <32>; // 32 bytes
+ d-cache-size = <0x8000>; // L1, 32K bytes
+ i-cache-size = <0x8000>; // L1, 32K bytes
timebase-frequency = <0>; // 33 MHz, from uboot
clock-frequency = <0>; // From U-Boot
bus-frequency = <0>; // From U-Boot
memory {
device_type = "memory";
- reg = <00000000 20000000 // DDR2 512M at 0
+ reg = <0x0 0x20000000 // DDR2 512M at 0
>;
};
#address-cells = <1>;
#size-cells = <1>;
device_type = "tsi-bridge";
- ranges = <00000000 c0000000 00010000>;
- reg = <c0000000 00010000>;
+ ranges = <0x0 0xc0000000 0x10000>;
+ reg = <0xc0000000 0x10000>;
bus-frequency = <0>;
i2c@7000 {
interrupt-parent = <&mpic>;
- interrupts = <E 0>;
- reg = <7000 400>;
+ interrupts = <14 0>;
+ reg = <0x7000 0x400>;
device_type = "i2c";
compatible = "tsi108-i2c";
};
MDIO: mdio@6000 {
device_type = "mdio";
compatible = "tsi108-mdio";
- reg = <6000 50>;
+ reg = <0x6000 0x50>;
#address-cells = <1>;
#size-cells = <0>;
phy8: ethernet-phy@8 {
interrupt-parent = <&mpic>;
interrupts = <2 1>;
- reg = <8>;
+ reg = <0x8>;
};
phy9: ethernet-phy@9 {
interrupt-parent = <&mpic>;
interrupts = <2 1>;
- reg = <9>;
+ reg = <0x9>;
};
};
#size-cells = <0>;
device_type = "network";
compatible = "tsi108-ethernet";
- reg = <6000 200>;
+ reg = <0x6000 0x200>;
address = [ 00 06 D2 00 00 01 ];
- interrupts = <10 2>;
+ interrupts = <16 2>;
interrupt-parent = <&mpic>;
mdio-handle = <&MDIO>;
phy-handle = <&phy8>;
#size-cells = <0>;
device_type = "network";
compatible = "tsi108-ethernet";
- reg = <6400 200>;
+ reg = <0x6400 0x200>;
address = [ 00 06 D2 00 00 02 ];
- interrupts = <11 2>;
+ interrupts = <17 2>;
interrupt-parent = <&mpic>;
mdio-handle = <&MDIO>;
phy-handle = <&phy9>;
serial@7808 {
device_type = "serial";
compatible = "ns16550";
- reg = <7808 200>;
- clock-frequency = <3f6b5a00>;
- interrupts = <c 0>;
+ reg = <0x7808 0x200>;
+ clock-frequency = <1064000000>;
+ interrupts = <12 0>;
interrupt-parent = <&mpic>;
};
serial@7c08 {
device_type = "serial";
compatible = "ns16550";
- reg = <7c08 200>;
- clock-frequency = <3f6b5a00>;
- interrupts = <d 0>;
+ reg = <0x7c08 0x200>;
+ clock-frequency = <1064000000>;
+ interrupts = <13 0>;
interrupt-parent = <&mpic>;
};
interrupt-controller;
#address-cells = <0>;
#interrupt-cells = <2>;
- reg = <7400 400>;
+ reg = <0x7400 0x400>;
compatible = "chrp,open-pic";
device_type = "open-pic";
big-endian;
#interrupt-cells = <1>;
#size-cells = <2>;
#address-cells = <3>;
- reg = <1000 1000>;
+ reg = <0x1000 0x1000>;
bus-range = <0 0>;
- ranges = <02000000 0 e0000000 e0000000 0 1A000000
- 01000000 0 00000000 fa000000 0 00010000>;
- clock-frequency = <7f28154>;
+ ranges = <0x2000000 0x0 0xe0000000 0xe0000000 0x0 0x1a000000
+ 0x1000000 0x0 0x0 0xfa000000 0x0 0x10000>;
+ clock-frequency = <133333332>;
interrupt-parent = <&mpic>;
- interrupts = <17 2>;
- interrupt-map-mask = <f800 0 0 7>;
+ interrupts = <23 2>;
+ interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
interrupt-map = <
/* IDSEL 0x11 */
- 0800 0 0 1 &RT0 24 0
- 0800 0 0 2 &RT0 25 0
- 0800 0 0 3 &RT0 26 0
- 0800 0 0 4 &RT0 27 0
+ 0x800 0x0 0x0 0x1 &RT0 0x24 0x0
+ 0x800 0x0 0x0 0x2 &RT0 0x25 0x0
+ 0x800 0x0 0x0 0x3 &RT0 0x26 0x0
+ 0x800 0x0 0x0 0x4 &RT0 0x27 0x0
/* IDSEL 0x12 */
- 1000 0 0 1 &RT0 25 0
- 1000 0 0 2 &RT0 26 0
- 1000 0 0 3 &RT0 27 0
- 1000 0 0 4 &RT0 24 0
+ 0x1000 0x0 0x0 0x1 &RT0 0x25 0x0
+ 0x1000 0x0 0x0 0x2 &RT0 0x26 0x0
+ 0x1000 0x0 0x0 0x3 &RT0 0x27 0x0
+ 0x1000 0x0 0x0 0x4 &RT0 0x24 0x0
/* IDSEL 0x13 */
- 1800 0 0 1 &RT0 26 0
- 1800 0 0 2 &RT0 27 0
- 1800 0 0 3 &RT0 24 0
- 1800 0 0 4 &RT0 25 0
+ 0x1800 0x0 0x0 0x1 &RT0 0x26 0x0
+ 0x1800 0x0 0x0 0x2 &RT0 0x27 0x0
+ 0x1800 0x0 0x0 0x3 &RT0 0x24 0x0
+ 0x1800 0x0 0x0 0x4 &RT0 0x25 0x0
/* IDSEL 0x14 */
- 2000 0 0 1 &RT0 27 0
- 2000 0 0 2 &RT0 24 0
- 2000 0 0 3 &RT0 25 0
- 2000 0 0 4 &RT0 26 0
+ 0x2000 0x0 0x0 0x1 &RT0 0x27 0x0
+ 0x2000 0x0 0x0 0x2 &RT0 0x24 0x0
+ 0x2000 0x0 0x0 0x3 &RT0 0x25 0x0
+ 0x2000 0x0 0x0 0x4 &RT0 0x26 0x0
>;
RT0: router@1180 {
#address-cells = <0>;
#interrupt-cells = <2>;
big-endian;
- interrupts = <17 2>;
+ interrupts = <23 2>;
interrupt-parent = <&mpic>;
};
};
/*
* MPC8272 ADS Device Tree Source
*
- * Copyright 2005 Freescale Semiconductor Inc.
+ * Copyright 2005,2008 Freescale Semiconductor Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* option) any later version.
*/
+/dts-v1/;
+
/ {
model = "MPC8272ADS";
compatible = "fsl,mpc8272ads";
PowerPC,8272@0 {
device_type = "cpu";
- reg = <0>;
- d-cache-line-size = <d#32>;
- i-cache-line-size = <d#32>;
- d-cache-size = <d#16384>;
- i-cache-size = <d#16384>;
+ reg = <0x0>;
+ d-cache-line-size = <32>;
+ i-cache-line-size = <32>;
+ d-cache-size = <16384>;
+ i-cache-size = <16384>;
timebase-frequency = <0>;
bus-frequency = <0>;
clock-frequency = <0>;
memory {
device_type = "memory";
- reg = <0 0>;
+ reg = <0x0 0x0>;
};
localbus@f0010100 {
"fsl,pq2-localbus";
#address-cells = <2>;
#size-cells = <1>;
- reg = <f0010100 40>;
+ reg = <0xf0010100 0x40>;
- ranges = <0 0 fe000000 02000000
- 1 0 f4500000 00008000
- 3 0 f8200000 00008000>;
+ ranges = <0x0 0x0 0xfe000000 0x2000000
+ 0x1 0x0 0xf4500000 0x8000
+ 0x3 0x0 0xf8200000 0x8000>;
flash@0,0 {
compatible = "jedec-flash";
- reg = <0 0 2000000>;
+ reg = <0x0 0x0 0x2000000>;
bank-width = <4>;
device-width = <1>;
};
board-control@1,0 {
- reg = <1 0 20>;
+ reg = <0x1 0x0 0x20>;
compatible = "fsl,mpc8272ads-bcsr";
};
"fsl,pq2ads-pci-pic";
#interrupt-cells = <1>;
interrupt-controller;
- reg = <3 0 8>;
+ reg = <0x3 0x0 0x8>;
interrupt-parent = <&PIC>;
- interrupts = <14 8>;
+ interrupts = <20 8>;
};
};
pci@f0010800 {
device_type = "pci";
- reg = <f0010800 10c f00101ac 8 f00101c4 8>;
+ reg = <0xf0010800 0x10c 0xf00101ac 0x8 0xf00101c4 0x8>;
compatible = "fsl,mpc8272-pci", "fsl,pq2-pci";
#interrupt-cells = <1>;
#size-cells = <2>;
#address-cells = <3>;
- clock-frequency = <d#66666666>;
- interrupt-map-mask = <f800 0 0 7>;
+ clock-frequency = <66666666>;
+ interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
interrupt-map = <
/* IDSEL 0x16 */
- b000 0 0 1 &PCI_PIC 0
- b000 0 0 2 &PCI_PIC 1
- b000 0 0 3 &PCI_PIC 2
- b000 0 0 4 &PCI_PIC 3
+ 0xb000 0x0 0x0 0x1 &PCI_PIC 0
+ 0xb000 0x0 0x0 0x2 &PCI_PIC 1
+ 0xb000 0x0 0x0 0x3 &PCI_PIC 2
+ 0xb000 0x0 0x0 0x4 &PCI_PIC 3
/* IDSEL 0x17 */
- b800 0 0 1 &PCI_PIC 4
- b800 0 0 2 &PCI_PIC 5
- b800 0 0 3 &PCI_PIC 6
- b800 0 0 4 &PCI_PIC 7
+ 0xb800 0x0 0x0 0x1 &PCI_PIC 4
+ 0xb800 0x0 0x0 0x2 &PCI_PIC 5
+ 0xb800 0x0 0x0 0x3 &PCI_PIC 6
+ 0xb800 0x0 0x0 0x4 &PCI_PIC 7
/* IDSEL 0x18 */
- c000 0 0 1 &PCI_PIC 8
- c000 0 0 2 &PCI_PIC 9
- c000 0 0 3 &PCI_PIC a
- c000 0 0 4 &PCI_PIC b>;
+ 0xc000 0x0 0x0 0x1 &PCI_PIC 8
+ 0xc000 0x0 0x0 0x2 &PCI_PIC 9
+ 0xc000 0x0 0x0 0x3 &PCI_PIC 10
+ 0xc000 0x0 0x0 0x4 &PCI_PIC 11>;
interrupt-parent = <&PIC>;
- interrupts = <12 8>;
- ranges = <42000000 0 80000000 80000000 0 20000000
- 02000000 0 a0000000 a0000000 0 20000000
- 01000000 0 00000000 f6000000 0 02000000>;
+ interrupts = <18 8>;
+ ranges = <0x42000000 0x0 0x80000000 0x80000000 0x0 0x20000000
+ 0x2000000 0x0 0xa0000000 0xa0000000 0x0 0x20000000
+ 0x1000000 0x0 0x0 0xf6000000 0x0 0x2000000>;
};
soc@f0000000 {
#size-cells = <1>;
device_type = "soc";
compatible = "fsl,mpc8272", "fsl,pq2-soc";
- ranges = <00000000 f0000000 00053000>;
+ ranges = <0x0 0xf0000000 0x53000>;
// Temporary -- will go away once kernel uses ranges for get_immrbase().
- reg = <f0000000 00053000>;
+ reg = <0xf0000000 0x53000>;
cpm@119c0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "fsl,mpc8272-cpm", "fsl,cpm2";
- reg = <119c0 30>;
+ reg = <0x119c0 0x30>;
ranges;
muram@0 {
#address-cells = <1>;
#size-cells = <1>;
- ranges = <0 0 10000>;
+ ranges = <0x0 0x0 0x10000>;
data@0 {
compatible = "fsl,cpm-muram-data";
- reg = <0 2000 9800 800>;
+ reg = <0x0 0x2000 0x9800 0x800>;
};
};
compatible = "fsl,mpc8272-brg",
"fsl,cpm2-brg",
"fsl,cpm-brg";
- reg = <119f0 10 115f0 10>;
+ reg = <0x119f0 0x10 0x115f0 0x10>;
};
serial@11a00 {
device_type = "serial";
compatible = "fsl,mpc8272-scc-uart",
"fsl,cpm2-scc-uart";
- reg = <11a00 20 8000 100>;
- interrupts = <28 8>;
+ reg = <0x11a00 0x20 0x8000 0x100>;
+ interrupts = <40 8>;
interrupt-parent = <&PIC>;
fsl,cpm-brg = <1>;
- fsl,cpm-command = <00800000>;
+ fsl,cpm-command = <0x800000>;
};
serial@11a60 {
device_type = "serial";
compatible = "fsl,mpc8272-scc-uart",
"fsl,cpm2-scc-uart";
- reg = <11a60 20 8300 100>;
- interrupts = <2b 8>;
+ reg = <0x11a60 0x20 0x8300 0x100>;
+ interrupts = <43 8>;
interrupt-parent = <&PIC>;
fsl,cpm-brg = <4>;
- fsl,cpm-command = <0ce00000>;
+ fsl,cpm-command = <0xce00000>;
};
mdio@10d40 {
compatible = "fsl,mpc8272ads-mdio-bitbang",
"fsl,mpc8272-mdio-bitbang",
"fsl,cpm2-mdio-bitbang";
- reg = <10d40 14>;
+ reg = <0x10d40 0x14>;
#address-cells = <1>;
#size-cells = <0>;
- fsl,mdio-pin = <12>;
- fsl,mdc-pin = <13>;
+ fsl,mdio-pin = <18>;
+ fsl,mdc-pin = <19>;
PHY0: ethernet-phy@0 {
interrupt-parent = <&PIC>;
- interrupts = <17 8>;
- reg = <0>;
+ interrupts = <23 8>;
+ reg = <0x0>;
device_type = "ethernet-phy";
};
PHY1: ethernet-phy@1 {
interrupt-parent = <&PIC>;
- interrupts = <17 8>;
- reg = <3>;
+ interrupts = <23 8>;
+ reg = <0x3>;
device_type = "ethernet-phy";
};
};
device_type = "network";
compatible = "fsl,mpc8272-fcc-enet",
"fsl,cpm2-fcc-enet";
- reg = <11300 20 8400 100 11390 1>;
+ reg = <0x11300 0x20 0x8400 0x100 0x11390 0x1>;
local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <20 8>;
+ interrupts = <32 8>;
interrupt-parent = <&PIC>;
phy-handle = <&PHY0>;
linux,network-index = <0>;
- fsl,cpm-command = <12000300>;
+ fsl,cpm-command = <0x12000300>;
};
ethernet@11320 {
device_type = "network";
compatible = "fsl,mpc8272-fcc-enet",
"fsl,cpm2-fcc-enet";
- reg = <11320 20 8500 100 113b0 1>;
+ reg = <0x11320 0x20 0x8500 0x100 0x113b0 0x1>;
local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <21 8>;
+ interrupts = <33 8>;
interrupt-parent = <&PIC>;
phy-handle = <&PHY1>;
linux,network-index = <1>;
- fsl,cpm-command = <16200300>;
+ fsl,cpm-command = <0x16200300>;
};
};
PIC: interrupt-controller@10c00 {
#interrupt-cells = <2>;
interrupt-controller;
- reg = <10c00 80>;
+ reg = <0x10c00 0x80>;
compatible = "fsl,mpc8272-pic", "fsl,cpm2-pic";
};
"fsl,talitos-sec2",
"fsl,talitos",
"talitos";
- reg = <30000 10000>;
- interrupts = <b 8>;
+ reg = <0x30000 0x10000>;
+ interrupts = <11 8>;
interrupt-parent = <&PIC>;
num-channels = <4>;
- channel-fifo-len = <18>;
- exec-units-mask = <0000007e>;
+ channel-fifo-len = <24>;
+ exec-units-mask = <0x7e>;
/* desc mask is for rev1.x, we need runtime fixup for >=2.x */
- descriptor-types-mask = <01010ebf>;
+ descriptor-types-mask = <0x1010ebf>;
};
};
enet0: ucc@2200 {
device_type = "network";
compatible = "ucc_geth";
- model = "UCC";
cell-index = <3>;
- device-id = <3>;
reg = <0x2200 0x200>;
interrupts = <34>;
interrupt-parent = <&qeic>;
enet1: ucc@3200 {
device_type = "network";
compatible = "ucc_geth";
- model = "UCC";
cell-index = <4>;
- device-id = <4>;
reg = <0x3200 0x200>;
interrupts = <35>;
interrupt-parent = <&qeic>;
ucc@2400 {
device_type = "serial";
compatible = "ucc_uart";
- model = "UCC";
- device-id = <5>; /* The UCC number, 1-7*/
+ cell-index = <5>; /* The UCC number, 1-7*/
port-number = <0>; /* Which ttyQEx device */
soft-uart; /* We need Soft-UART */
reg = <0x2400 0x200>;
enet0: ucc@3000 {
device_type = "network";
compatible = "ucc_geth";
- model = "UCC";
cell-index = <2>;
- device-id = <2>;
reg = <0x3000 0x200>;
interrupts = <33>;
interrupt-parent = <&qeic>;
enet1: ucc@2200 {
device_type = "network";
compatible = "ucc_geth";
- model = "UCC";
cell-index = <3>;
- device-id = <3>;
reg = <0x2200 0x200>;
interrupts = <34>;
interrupt-parent = <&qeic>;
enet0: ucc@2000 {
device_type = "network";
compatible = "ucc_geth";
- model = "UCC";
cell-index = <1>;
- device-id = <1>;
reg = <0x2000 0x200>;
interrupts = <32>;
interrupt-parent = <&qeic>;
enet1: ucc@3000 {
device_type = "network";
compatible = "ucc_geth";
- model = "UCC";
cell-index = <2>;
- device-id = <2>;
reg = <0x3000 0x200>;
interrupts = <33>;
interrupt-parent = <&qeic>;
/*
* MPC8540 ADS Device Tree Source
*
- * Copyright 2006 Freescale Semiconductor Inc.
+ * Copyright 2006, 2008 Freescale Semiconductor Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* option) any later version.
*/
+/dts-v1/;
/ {
model = "MPC8540ADS";
PowerPC,8540@0 {
device_type = "cpu";
- reg = <0>;
- d-cache-line-size = <20>; // 32 bytes
- i-cache-line-size = <20>; // 32 bytes
- d-cache-size = <8000>; // L1, 32K
- i-cache-size = <8000>; // L1, 32K
+ reg = <0x0>;
+ d-cache-line-size = <32>; // 32 bytes
+ i-cache-line-size = <32>; // 32 bytes
+ d-cache-size = <0x8000>; // L1, 32K
+ i-cache-size = <0x8000>; // L1, 32K
timebase-frequency = <0>; // 33 MHz, from uboot
bus-frequency = <0>; // 166 MHz
clock-frequency = <0>; // 825 MHz, from uboot
memory {
device_type = "memory";
- reg = <00000000 08000000>; // 128M at 0x0
+ reg = <0x0 0x8000000>; // 128M at 0x0
};
soc8540@e0000000 {
#address-cells = <1>;
#size-cells = <1>;
device_type = "soc";
- ranges = <0 e0000000 00100000>;
- reg = <e0000000 00100000>; // CCSRBAR 1M
+ ranges = <0x0 0xe0000000 0x100000>;
+ reg = <0xe0000000 0x100000>; // CCSRBAR 1M
bus-frequency = <0>;
memory-controller@2000 {
compatible = "fsl,8540-memory-controller";
- reg = <2000 1000>;
+ reg = <0x2000 0x1000>;
interrupt-parent = <&mpic>;
- interrupts = <12 2>;
+ interrupts = <18 2>;
};
l2-cache-controller@20000 {
compatible = "fsl,8540-l2-cache-controller";
- reg = <20000 1000>;
- cache-line-size = <20>; // 32 bytes
- cache-size = <40000>; // L2, 256K
+ reg = <0x20000 0x1000>;
+ cache-line-size = <32>; // 32 bytes
+ cache-size = <0x40000>; // L2, 256K
interrupt-parent = <&mpic>;
- interrupts = <10 2>;
+ interrupts = <16 2>;
};
i2c@3000 {
#size-cells = <0>;
cell-index = <0>;
compatible = "fsl-i2c";
- reg = <3000 100>;
- interrupts = <2b 2>;
+ reg = <0x3000 0x100>;
+ interrupts = <43 2>;
interrupt-parent = <&mpic>;
dfsrr;
};
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,gianfar-mdio";
- reg = <24520 20>;
+ reg = <0x24520 0x20>;
phy0: ethernet-phy@0 {
interrupt-parent = <&mpic>;
interrupts = <5 1>;
- reg = <0>;
+ reg = <0x0>;
device_type = "ethernet-phy";
};
phy1: ethernet-phy@1 {
interrupt-parent = <&mpic>;
interrupts = <5 1>;
- reg = <1>;
+ reg = <0x1>;
device_type = "ethernet-phy";
};
phy3: ethernet-phy@3 {
interrupt-parent = <&mpic>;
interrupts = <7 1>;
- reg = <3>;
+ reg = <0x3>;
device_type = "ethernet-phy";
};
};
device_type = "network";
model = "TSEC";
compatible = "gianfar";
- reg = <24000 1000>;
+ reg = <0x24000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <1d 2 1e 2 22 2>;
+ interrupts = <29 2 30 2 34 2>;
interrupt-parent = <&mpic>;
phy-handle = <&phy0>;
};
device_type = "network";
model = "TSEC";
compatible = "gianfar";
- reg = <25000 1000>;
+ reg = <0x25000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <23 2 24 2 28 2>;
+ interrupts = <35 2 36 2 40 2>;
interrupt-parent = <&mpic>;
phy-handle = <&phy1>;
};
device_type = "network";
model = "FEC";
compatible = "gianfar";
- reg = <26000 1000>;
+ reg = <0x26000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <29 2>;
+ interrupts = <41 2>;
interrupt-parent = <&mpic>;
phy-handle = <&phy3>;
};
cell-index = <0>;
device_type = "serial";
compatible = "ns16550";
- reg = <4500 100>; // reg base, size
+ reg = <0x4500 0x100>; // reg base, size
clock-frequency = <0>; // should we fill in in uboot?
- interrupts = <2a 2>;
+ interrupts = <42 2>;
interrupt-parent = <&mpic>;
};
cell-index = <1>;
device_type = "serial";
compatible = "ns16550";
- reg = <4600 100>; // reg base, size
+ reg = <0x4600 0x100>; // reg base, size
clock-frequency = <0>; // should we fill in in uboot?
- interrupts = <2a 2>;
+ interrupts = <42 2>;
interrupt-parent = <&mpic>;
};
mpic: pic@40000 {
interrupt-controller;
#address-cells = <0>;
#interrupt-cells = <2>;
- reg = <40000 40000>;
+ reg = <0x40000 0x40000>;
compatible = "chrp,open-pic";
device_type = "open-pic";
big-endian;
pci0: pci@e0008000 {
cell-index = <0>;
- interrupt-map-mask = <f800 0 0 7>;
+ interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
interrupt-map = <
/* IDSEL 0x02 */
- 1000 0 0 1 &mpic 1 1
- 1000 0 0 2 &mpic 2 1
- 1000 0 0 3 &mpic 3 1
- 1000 0 0 4 &mpic 4 1
+ 0x1000 0x0 0x0 0x1 &mpic 0x1 0x1
+ 0x1000 0x0 0x0 0x2 &mpic 0x2 0x1
+ 0x1000 0x0 0x0 0x3 &mpic 0x3 0x1
+ 0x1000 0x0 0x0 0x4 &mpic 0x4 0x1
/* IDSEL 0x03 */
- 1800 0 0 1 &mpic 4 1
- 1800 0 0 2 &mpic 1 1
- 1800 0 0 3 &mpic 2 1
- 1800 0 0 4 &mpic 3 1
+ 0x1800 0x0 0x0 0x1 &mpic 0x4 0x1
+ 0x1800 0x0 0x0 0x2 &mpic 0x1 0x1
+ 0x1800 0x0 0x0 0x3 &mpic 0x2 0x1
+ 0x1800 0x0 0x0 0x4 &mpic 0x3 0x1
/* IDSEL 0x04 */
- 2000 0 0 1 &mpic 3 1
- 2000 0 0 2 &mpic 4 1
- 2000 0 0 3 &mpic 1 1
- 2000 0 0 4 &mpic 2 1
+ 0x2000 0x0 0x0 0x1 &mpic 0x3 0x1
+ 0x2000 0x0 0x0 0x2 &mpic 0x4 0x1
+ 0x2000 0x0 0x0 0x3 &mpic 0x1 0x1
+ 0x2000 0x0 0x0 0x4 &mpic 0x2 0x1
/* IDSEL 0x05 */
- 2800 0 0 1 &mpic 2 1
- 2800 0 0 2 &mpic 3 1
- 2800 0 0 3 &mpic 4 1
- 2800 0 0 4 &mpic 1 1
+ 0x2800 0x0 0x0 0x1 &mpic 0x2 0x1
+ 0x2800 0x0 0x0 0x2 &mpic 0x3 0x1
+ 0x2800 0x0 0x0 0x3 &mpic 0x4 0x1
+ 0x2800 0x0 0x0 0x4 &mpic 0x1 0x1
/* IDSEL 0x0c */
- 6000 0 0 1 &mpic 1 1
- 6000 0 0 2 &mpic 2 1
- 6000 0 0 3 &mpic 3 1
- 6000 0 0 4 &mpic 4 1
+ 0x6000 0x0 0x0 0x1 &mpic 0x1 0x1
+ 0x6000 0x0 0x0 0x2 &mpic 0x2 0x1
+ 0x6000 0x0 0x0 0x3 &mpic 0x3 0x1
+ 0x6000 0x0 0x0 0x4 &mpic 0x4 0x1
/* IDSEL 0x0d */
- 6800 0 0 1 &mpic 4 1
- 6800 0 0 2 &mpic 1 1
- 6800 0 0 3 &mpic 2 1
- 6800 0 0 4 &mpic 3 1
+ 0x6800 0x0 0x0 0x1 &mpic 0x4 0x1
+ 0x6800 0x0 0x0 0x2 &mpic 0x1 0x1
+ 0x6800 0x0 0x0 0x3 &mpic 0x2 0x1
+ 0x6800 0x0 0x0 0x4 &mpic 0x3 0x1
/* IDSEL 0x0e */
- 7000 0 0 1 &mpic 3 1
- 7000 0 0 2 &mpic 4 1
- 7000 0 0 3 &mpic 1 1
- 7000 0 0 4 &mpic 2 1
+ 0x7000 0x0 0x0 0x1 &mpic 0x3 0x1
+ 0x7000 0x0 0x0 0x2 &mpic 0x4 0x1
+ 0x7000 0x0 0x0 0x3 &mpic 0x1 0x1
+ 0x7000 0x0 0x0 0x4 &mpic 0x2 0x1
/* IDSEL 0x0f */
- 7800 0 0 1 &mpic 2 1
- 7800 0 0 2 &mpic 3 1
- 7800 0 0 3 &mpic 4 1
- 7800 0 0 4 &mpic 1 1
+ 0x7800 0x0 0x0 0x1 &mpic 0x2 0x1
+ 0x7800 0x0 0x0 0x2 &mpic 0x3 0x1
+ 0x7800 0x0 0x0 0x3 &mpic 0x4 0x1
+ 0x7800 0x0 0x0 0x4 &mpic 0x1 0x1
/* IDSEL 0x12 */
- 9000 0 0 1 &mpic 1 1
- 9000 0 0 2 &mpic 2 1
- 9000 0 0 3 &mpic 3 1
- 9000 0 0 4 &mpic 4 1
+ 0x9000 0x0 0x0 0x1 &mpic 0x1 0x1
+ 0x9000 0x0 0x0 0x2 &mpic 0x2 0x1
+ 0x9000 0x0 0x0 0x3 &mpic 0x3 0x1
+ 0x9000 0x0 0x0 0x4 &mpic 0x4 0x1
/* IDSEL 0x13 */
- 9800 0 0 1 &mpic 4 1
- 9800 0 0 2 &mpic 1 1
- 9800 0 0 3 &mpic 2 1
- 9800 0 0 4 &mpic 3 1
+ 0x9800 0x0 0x0 0x1 &mpic 0x4 0x1
+ 0x9800 0x0 0x0 0x2 &mpic 0x1 0x1
+ 0x9800 0x0 0x0 0x3 &mpic 0x2 0x1
+ 0x9800 0x0 0x0 0x4 &mpic 0x3 0x1
/* IDSEL 0x14 */
- a000 0 0 1 &mpic 3 1
- a000 0 0 2 &mpic 4 1
- a000 0 0 3 &mpic 1 1
- a000 0 0 4 &mpic 2 1
+ 0xa000 0x0 0x0 0x1 &mpic 0x3 0x1
+ 0xa000 0x0 0x0 0x2 &mpic 0x4 0x1
+ 0xa000 0x0 0x0 0x3 &mpic 0x1 0x1
+ 0xa000 0x0 0x0 0x4 &mpic 0x2 0x1
/* IDSEL 0x15 */
- a800 0 0 1 &mpic 2 1
- a800 0 0 2 &mpic 3 1
- a800 0 0 3 &mpic 4 1
- a800 0 0 4 &mpic 1 1>;
+ 0xa800 0x0 0x0 0x1 &mpic 0x2 0x1
+ 0xa800 0x0 0x0 0x2 &mpic 0x3 0x1
+ 0xa800 0x0 0x0 0x3 &mpic 0x4 0x1
+ 0xa800 0x0 0x0 0x4 &mpic 0x1 0x1>;
interrupt-parent = <&mpic>;
- interrupts = <18 2>;
+ interrupts = <24 2>;
bus-range = <0 0>;
- ranges = <02000000 0 80000000 80000000 0 20000000
- 01000000 0 00000000 e2000000 0 00100000>;
- clock-frequency = <3f940aa>;
+ ranges = <0x2000000 0x0 0x80000000 0x80000000 0x0 0x20000000
+ 0x1000000 0x0 0x0 0xe2000000 0x0 0x100000>;
+ clock-frequency = <66666666>;
#interrupt-cells = <1>;
#size-cells = <2>;
#address-cells = <3>;
- reg = <e0008000 1000>;
+ reg = <0xe0008000 0x1000>;
compatible = "fsl,mpc8540-pcix", "fsl,mpc8540-pci";
device_type = "pci";
};
/*
* MPC8541 CDS Device Tree Source
*
- * Copyright 2006 Freescale Semiconductor Inc.
+ * Copyright 2006, 2008 Freescale Semiconductor Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* option) any later version.
*/
+/dts-v1/;
/ {
model = "MPC8541CDS";
PowerPC,8541@0 {
device_type = "cpu";
- reg = <0>;
- d-cache-line-size = <20>; // 32 bytes
- i-cache-line-size = <20>; // 32 bytes
- d-cache-size = <8000>; // L1, 32K
- i-cache-size = <8000>; // L1, 32K
+ reg = <0x0>;
+ d-cache-line-size = <32>; // 32 bytes
+ i-cache-line-size = <32>; // 32 bytes
+ d-cache-size = <0x8000>; // L1, 32K
+ i-cache-size = <0x8000>; // L1, 32K
timebase-frequency = <0>; // 33 MHz, from uboot
bus-frequency = <0>; // 166 MHz
clock-frequency = <0>; // 825 MHz, from uboot
memory {
device_type = "memory";
- reg = <00000000 08000000>; // 128M at 0x0
+ reg = <0x0 0x8000000>; // 128M at 0x0
};
soc8541@e0000000 {
#address-cells = <1>;
#size-cells = <1>;
device_type = "soc";
- ranges = <0 e0000000 00100000>;
- reg = <e0000000 00001000>; // CCSRBAR 1M
+ ranges = <0x0 0xe0000000 0x100000>;
+ reg = <0xe0000000 0x1000>; // CCSRBAR 1M
bus-frequency = <0>;
memory-controller@2000 {
compatible = "fsl,8541-memory-controller";
- reg = <2000 1000>;
+ reg = <0x2000 0x1000>;
interrupt-parent = <&mpic>;
- interrupts = <12 2>;
+ interrupts = <18 2>;
};
l2-cache-controller@20000 {
compatible = "fsl,8541-l2-cache-controller";
- reg = <20000 1000>;
- cache-line-size = <20>; // 32 bytes
- cache-size = <40000>; // L2, 256K
+ reg = <0x20000 0x1000>;
+ cache-line-size = <32>; // 32 bytes
+ cache-size = <0x40000>; // L2, 256K
interrupt-parent = <&mpic>;
- interrupts = <10 2>;
+ interrupts = <16 2>;
};
i2c@3000 {
#size-cells = <0>;
cell-index = <0>;
compatible = "fsl-i2c";
- reg = <3000 100>;
- interrupts = <2b 2>;
+ reg = <0x3000 0x100>;
+ interrupts = <43 2>;
interrupt-parent = <&mpic>;
dfsrr;
};
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,gianfar-mdio";
- reg = <24520 20>;
+ reg = <0x24520 0x20>;
phy0: ethernet-phy@0 {
interrupt-parent = <&mpic>;
interrupts = <5 1>;
- reg = <0>;
+ reg = <0x0>;
device_type = "ethernet-phy";
};
phy1: ethernet-phy@1 {
interrupt-parent = <&mpic>;
interrupts = <5 1>;
- reg = <1>;
+ reg = <0x1>;
device_type = "ethernet-phy";
};
};
device_type = "network";
model = "TSEC";
compatible = "gianfar";
- reg = <24000 1000>;
+ reg = <0x24000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <1d 2 1e 2 22 2>;
+ interrupts = <29 2 30 2 34 2>;
interrupt-parent = <&mpic>;
phy-handle = <&phy0>;
};
device_type = "network";
model = "TSEC";
compatible = "gianfar";
- reg = <25000 1000>;
+ reg = <0x25000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <23 2 24 2 28 2>;
+ interrupts = <35 2 36 2 40 2>;
interrupt-parent = <&mpic>;
phy-handle = <&phy1>;
};
cell-index = <0>;
device_type = "serial";
compatible = "ns16550";
- reg = <4500 100>; // reg base, size
+ reg = <0x4500 0x100>; // reg base, size
clock-frequency = <0>; // should we fill in in uboot?
- interrupts = <2a 2>;
+ interrupts = <42 2>;
interrupt-parent = <&mpic>;
};
cell-index = <1>;
device_type = "serial";
compatible = "ns16550";
- reg = <4600 100>; // reg base, size
+ reg = <0x4600 0x100>; // reg base, size
clock-frequency = <0>; // should we fill in in uboot?
- interrupts = <2a 2>;
+ interrupts = <42 2>;
interrupt-parent = <&mpic>;
};
interrupt-controller;
#address-cells = <0>;
#interrupt-cells = <2>;
- reg = <40000 40000>;
+ reg = <0x40000 0x40000>;
compatible = "chrp,open-pic";
device_type = "open-pic";
big-endian;
#address-cells = <1>;
#size-cells = <1>;
compatible = "fsl,mpc8541-cpm", "fsl,cpm2";
- reg = <919c0 30>;
+ reg = <0x919c0 0x30>;
ranges;
muram@80000 {
#address-cells = <1>;
#size-cells = <1>;
- ranges = <0 80000 10000>;
+ ranges = <0x0 0x80000 0x10000>;
data@0 {
compatible = "fsl,cpm-muram-data";
- reg = <0 2000 9000 1000>;
+ reg = <0x0 0x2000 0x9000 0x1000>;
};
};
compatible = "fsl,mpc8541-brg",
"fsl,cpm2-brg",
"fsl,cpm-brg";
- reg = <919f0 10 915f0 10>;
+ reg = <0x919f0 0x10 0x915f0 0x10>;
};
cpmpic: pic@90c00 {
interrupt-controller;
#address-cells = <0>;
#interrupt-cells = <2>;
- interrupts = <2e 2>;
+ interrupts = <46 2>;
interrupt-parent = <&mpic>;
- reg = <90c00 80>;
+ reg = <0x90c00 0x80>;
compatible = "fsl,mpc8541-cpm-pic", "fsl,cpm2-pic";
};
};
pci0: pci@e0008000 {
cell-index = <0>;
- interrupt-map-mask = <1f800 0 0 7>;
+ interrupt-map-mask = <0x1f800 0x0 0x0 0x7>;
interrupt-map = <
/* IDSEL 0x10 */
- 08000 0 0 1 &mpic 0 1
- 08000 0 0 2 &mpic 1 1
- 08000 0 0 3 &mpic 2 1
- 08000 0 0 4 &mpic 3 1
+ 0x8000 0x0 0x0 0x1 &mpic 0x0 0x1
+ 0x8000 0x0 0x0 0x2 &mpic 0x1 0x1
+ 0x8000 0x0 0x0 0x3 &mpic 0x2 0x1
+ 0x8000 0x0 0x0 0x4 &mpic 0x3 0x1
/* IDSEL 0x11 */
- 08800 0 0 1 &mpic 0 1
- 08800 0 0 2 &mpic 1 1
- 08800 0 0 3 &mpic 2 1
- 08800 0 0 4 &mpic 3 1
+ 0x8800 0x0 0x0 0x1 &mpic 0x0 0x1
+ 0x8800 0x0 0x0 0x2 &mpic 0x1 0x1
+ 0x8800 0x0 0x0 0x3 &mpic 0x2 0x1
+ 0x8800 0x0 0x0 0x4 &mpic 0x3 0x1
/* IDSEL 0x12 (Slot 1) */
- 09000 0 0 1 &mpic 0 1
- 09000 0 0 2 &mpic 1 1
- 09000 0 0 3 &mpic 2 1
- 09000 0 0 4 &mpic 3 1
+ 0x9000 0x0 0x0 0x1 &mpic 0x0 0x1
+ 0x9000 0x0 0x0 0x2 &mpic 0x1 0x1
+ 0x9000 0x0 0x0 0x3 &mpic 0x2 0x1
+ 0x9000 0x0 0x0 0x4 &mpic 0x3 0x1
/* IDSEL 0x13 (Slot 2) */
- 09800 0 0 1 &mpic 1 1
- 09800 0 0 2 &mpic 2 1
- 09800 0 0 3 &mpic 3 1
- 09800 0 0 4 &mpic 0 1
+ 0x9800 0x0 0x0 0x1 &mpic 0x1 0x1
+ 0x9800 0x0 0x0 0x2 &mpic 0x2 0x1
+ 0x9800 0x0 0x0 0x3 &mpic 0x3 0x1
+ 0x9800 0x0 0x0 0x4 &mpic 0x0 0x1
/* IDSEL 0x14 (Slot 3) */
- 0a000 0 0 1 &mpic 2 1
- 0a000 0 0 2 &mpic 3 1
- 0a000 0 0 3 &mpic 0 1
- 0a000 0 0 4 &mpic 1 1
+ 0xa000 0x0 0x0 0x1 &mpic 0x2 0x1
+ 0xa000 0x0 0x0 0x2 &mpic 0x3 0x1
+ 0xa000 0x0 0x0 0x3 &mpic 0x0 0x1
+ 0xa000 0x0 0x0 0x4 &mpic 0x1 0x1
/* IDSEL 0x15 (Slot 4) */
- 0a800 0 0 1 &mpic 3 1
- 0a800 0 0 2 &mpic 0 1
- 0a800 0 0 3 &mpic 1 1
- 0a800 0 0 4 &mpic 2 1
+ 0xa800 0x0 0x0 0x1 &mpic 0x3 0x1
+ 0xa800 0x0 0x0 0x2 &mpic 0x0 0x1
+ 0xa800 0x0 0x0 0x3 &mpic 0x1 0x1
+ 0xa800 0x0 0x0 0x4 &mpic 0x2 0x1
/* Bus 1 (Tundra Bridge) */
/* IDSEL 0x12 (ISA bridge) */
- 19000 0 0 1 &mpic 0 1
- 19000 0 0 2 &mpic 1 1
- 19000 0 0 3 &mpic 2 1
- 19000 0 0 4 &mpic 3 1>;
+ 0x19000 0x0 0x0 0x1 &mpic 0x0 0x1
+ 0x19000 0x0 0x0 0x2 &mpic 0x1 0x1
+ 0x19000 0x0 0x0 0x3 &mpic 0x2 0x1
+ 0x19000 0x0 0x0 0x4 &mpic 0x3 0x1>;
interrupt-parent = <&mpic>;
- interrupts = <18 2>;
+ interrupts = <24 2>;
bus-range = <0 0>;
- ranges = <02000000 0 80000000 80000000 0 20000000
- 01000000 0 00000000 e2000000 0 00100000>;
- clock-frequency = <3f940aa>;
+ ranges = <0x2000000 0x0 0x80000000 0x80000000 0x0 0x20000000
+ 0x1000000 0x0 0x0 0xe2000000 0x0 0x100000>;
+ clock-frequency = <66666666>;
#interrupt-cells = <1>;
#size-cells = <2>;
#address-cells = <3>;
- reg = <e0008000 1000>;
+ reg = <0xe0008000 0x1000>;
compatible = "fsl,mpc8540-pci";
device_type = "pci";
i8259@19000 {
interrupt-controller;
device_type = "interrupt-controller";
- reg = <19000 0 0 0 1>;
+ reg = <0x19000 0x0 0x0 0x0 0x1>;
#address-cells = <0>;
#interrupt-cells = <2>;
compatible = "chrp,iic";
pci1: pci@e0009000 {
cell-index = <1>;
- interrupt-map-mask = <f800 0 0 7>;
+ interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
interrupt-map = <
/* IDSEL 0x15 */
- a800 0 0 1 &mpic b 1
- a800 0 0 2 &mpic b 1
- a800 0 0 3 &mpic b 1
- a800 0 0 4 &mpic b 1>;
+ 0xa800 0x0 0x0 0x1 &mpic 0xb 0x1
+ 0xa800 0x0 0x0 0x2 &mpic 0xb 0x1
+ 0xa800 0x0 0x0 0x3 &mpic 0xb 0x1
+ 0xa800 0x0 0x0 0x4 &mpic 0xb 0x1>;
interrupt-parent = <&mpic>;
- interrupts = <19 2>;
+ interrupts = <25 2>;
bus-range = <0 0>;
- ranges = <02000000 0 a0000000 a0000000 0 20000000
- 01000000 0 00000000 e3000000 0 00100000>;
- clock-frequency = <3f940aa>;
+ ranges = <0x2000000 0x0 0xa0000000 0xa0000000 0x0 0x20000000
+ 0x1000000 0x0 0x0 0xe3000000 0x0 0x100000>;
+ clock-frequency = <66666666>;
#interrupt-cells = <1>;
#size-cells = <2>;
#address-cells = <3>;
- reg = <e0009000 1000>;
+ reg = <0xe0009000 0x1000>;
compatible = "fsl,mpc8540-pci";
device_type = "pci";
};
/*
* MPC8544 DS Device Tree Source
*
- * Copyright 2007 Freescale Semiconductor Inc.
+ * Copyright 2007, 2008 Freescale Semiconductor Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* option) any later version.
*/
+/dts-v1/;
/ {
model = "MPC8544DS";
compatible = "MPC8544DS", "MPC85xxDS";
};
cpus {
- #cpus = <1>;
#address-cells = <1>;
#size-cells = <0>;
PowerPC,8544@0 {
device_type = "cpu";
- reg = <0>;
- d-cache-line-size = <20>; // 32 bytes
- i-cache-line-size = <20>; // 32 bytes
- d-cache-size = <8000>; // L1, 32K
- i-cache-size = <8000>; // L1, 32K
+ reg = <0x0>;
+ d-cache-line-size = <32>; // 32 bytes
+ i-cache-line-size = <32>; // 32 bytes
+ d-cache-size = <0x8000>; // L1, 32K
+ i-cache-size = <0x8000>; // L1, 32K
timebase-frequency = <0>;
bus-frequency = <0>;
clock-frequency = <0>;
memory {
device_type = "memory";
- reg = <00000000 00000000>; // Filled by U-Boot
+ reg = <0x0 0x0>; // Filled by U-Boot
};
soc8544@e0000000 {
#size-cells = <1>;
device_type = "soc";
- ranges = <00000000 e0000000 00100000>;
- reg = <e0000000 00001000>; // CCSRBAR 1M
+ ranges = <0x0 0xe0000000 0x100000>;
+ reg = <0xe0000000 0x1000>; // CCSRBAR 1M
bus-frequency = <0>; // Filled out by uboot.
memory-controller@2000 {
compatible = "fsl,8544-memory-controller";
- reg = <2000 1000>;
+ reg = <0x2000 0x1000>;
interrupt-parent = <&mpic>;
- interrupts = <12 2>;
+ interrupts = <18 2>;
};
l2-cache-controller@20000 {
compatible = "fsl,8544-l2-cache-controller";
- reg = <20000 1000>;
- cache-line-size = <20>; // 32 bytes
- cache-size = <40000>; // L2, 256K
+ reg = <0x20000 0x1000>;
+ cache-line-size = <32>; // 32 bytes
+ cache-size = <0x40000>; // L2, 256K
interrupt-parent = <&mpic>;
- interrupts = <10 2>;
+ interrupts = <16 2>;
};
i2c@3000 {
#size-cells = <0>;
cell-index = <0>;
compatible = "fsl-i2c";
- reg = <3000 100>;
- interrupts = <2b 2>;
+ reg = <0x3000 0x100>;
+ interrupts = <43 2>;
interrupt-parent = <&mpic>;
dfsrr;
};
#size-cells = <0>;
cell-index = <1>;
compatible = "fsl-i2c";
- reg = <3100 100>;
- interrupts = <2b 2>;
+ reg = <0x3100 0x100>;
+ interrupts = <43 2>;
interrupt-parent = <&mpic>;
dfsrr;
};
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,gianfar-mdio";
- reg = <24520 20>;
+ reg = <0x24520 0x20>;
phy0: ethernet-phy@0 {
interrupt-parent = <&mpic>;
- interrupts = <a 1>;
- reg = <0>;
+ interrupts = <10 1>;
+ reg = <0x0>;
device_type = "ethernet-phy";
};
phy1: ethernet-phy@1 {
interrupt-parent = <&mpic>;
- interrupts = <a 1>;
- reg = <1>;
+ interrupts = <10 1>;
+ reg = <0x1>;
device_type = "ethernet-phy";
};
};
+ dma@21300 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8544-dma", "fsl,eloplus-dma";
+ reg = <0x21300 0x4>;
+ ranges = <0x0 0x21100 0x200>;
+ cell-index = <0>;
+ dma-channel@0 {
+ compatible = "fsl,mpc8544-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x0 0x80>;
+ cell-index = <0>;
+ interrupt-parent = <&mpic>;
+ interrupts = <20 2>;
+ };
+ dma-channel@80 {
+ compatible = "fsl,mpc8544-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x80 0x80>;
+ cell-index = <1>;
+ interrupt-parent = <&mpic>;
+ interrupts = <21 2>;
+ };
+ dma-channel@100 {
+ compatible = "fsl,mpc8544-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x100 0x80>;
+ cell-index = <2>;
+ interrupt-parent = <&mpic>;
+ interrupts = <22 2>;
+ };
+ dma-channel@180 {
+ compatible = "fsl,mpc8544-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x180 0x80>;
+ cell-index = <3>;
+ interrupt-parent = <&mpic>;
+ interrupts = <23 2>;
+ };
+ };
+
enet0: ethernet@24000 {
cell-index = <0>;
device_type = "network";
model = "TSEC";
compatible = "gianfar";
- reg = <24000 1000>;
+ reg = <0x24000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <1d 2 1e 2 22 2>;
+ interrupts = <29 2 30 2 34 2>;
interrupt-parent = <&mpic>;
phy-handle = <&phy0>;
phy-connection-type = "rgmii-id";
device_type = "network";
model = "TSEC";
compatible = "gianfar";
- reg = <26000 1000>;
+ reg = <0x26000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <1f 2 20 2 21 2>;
+ interrupts = <31 2 32 2 33 2>;
interrupt-parent = <&mpic>;
phy-handle = <&phy1>;
phy-connection-type = "rgmii-id";
cell-index = <0>;
device_type = "serial";
compatible = "ns16550";
- reg = <4500 100>;
+ reg = <0x4500 0x100>;
clock-frequency = <0>;
- interrupts = <2a 2>;
+ interrupts = <42 2>;
interrupt-parent = <&mpic>;
};
cell-index = <1>;
device_type = "serial";
compatible = "ns16550";
- reg = <4600 100>;
+ reg = <0x4600 0x100>;
clock-frequency = <0>;
- interrupts = <2a 2>;
+ interrupts = <42 2>;
interrupt-parent = <&mpic>;
};
global-utilities@e0000 { //global utilities block
compatible = "fsl,mpc8548-guts";
- reg = <e0000 1000>;
+ reg = <0xe0000 0x1000>;
fsl,has-rstcr;
};
interrupt-controller;
#address-cells = <0>;
#interrupt-cells = <2>;
- reg = <40000 40000>;
+ reg = <0x40000 0x40000>;
compatible = "chrp,open-pic";
device_type = "open-pic";
big-endian;
cell-index = <0>;
compatible = "fsl,mpc8540-pci";
device_type = "pci";
- interrupt-map-mask = <f800 0 0 7>;
+ interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
interrupt-map = <
/* IDSEL 0x11 J17 Slot 1 */
- 8800 0 0 1 &mpic 2 1
- 8800 0 0 2 &mpic 3 1
- 8800 0 0 3 &mpic 4 1
- 8800 0 0 4 &mpic 1 1
+ 0x8800 0x0 0x0 0x1 &mpic 0x2 0x1
+ 0x8800 0x0 0x0 0x2 &mpic 0x3 0x1
+ 0x8800 0x0 0x0 0x3 &mpic 0x4 0x1
+ 0x8800 0x0 0x0 0x4 &mpic 0x1 0x1
/* IDSEL 0x12 J16 Slot 2 */
- 9000 0 0 1 &mpic 3 1
- 9000 0 0 2 &mpic 4 1
- 9000 0 0 3 &mpic 2 1
- 9000 0 0 4 &mpic 1 1>;
+ 0x9000 0x0 0x0 0x1 &mpic 0x3 0x1
+ 0x9000 0x0 0x0 0x2 &mpic 0x4 0x1
+ 0x9000 0x0 0x0 0x3 &mpic 0x2 0x1
+ 0x9000 0x0 0x0 0x4 &mpic 0x1 0x1>;
interrupt-parent = <&mpic>;
- interrupts = <18 2>;
- bus-range = <0 ff>;
- ranges = <02000000 0 c0000000 c0000000 0 20000000
- 01000000 0 00000000 e1000000 0 00010000>;
- clock-frequency = <3f940aa>;
+ interrupts = <24 2>;
+ bus-range = <0 255>;
+ ranges = <0x2000000 0x0 0xc0000000 0xc0000000 0x0 0x20000000
+ 0x1000000 0x0 0x0 0xe1000000 0x0 0x10000>;
+ clock-frequency = <66666666>;
#interrupt-cells = <1>;
#size-cells = <2>;
#address-cells = <3>;
- reg = <e0008000 1000>;
+ reg = <0xe0008000 0x1000>;
};
pci1: pcie@e0009000 {
#interrupt-cells = <1>;
#size-cells = <2>;
#address-cells = <3>;
- reg = <e0009000 1000>;
- bus-range = <0 ff>;
- ranges = <02000000 0 80000000 80000000 0 20000000
- 01000000 0 00000000 e1010000 0 00010000>;
- clock-frequency = <1fca055>;
+ reg = <0xe0009000 0x1000>;
+ bus-range = <0 255>;
+ ranges = <0x2000000 0x0 0x80000000 0x80000000 0x0 0x20000000
+ 0x1000000 0x0 0x0 0xe1010000 0x0 0x10000>;
+ clock-frequency = <33333333>;
interrupt-parent = <&mpic>;
- interrupts = <1a 2>;
- interrupt-map-mask = <f800 0 0 7>;
+ interrupts = <26 2>;
+ interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
interrupt-map = <
/* IDSEL 0x0 */
- 0000 0 0 1 &mpic 4 1
- 0000 0 0 2 &mpic 5 1
- 0000 0 0 3 &mpic 6 1
- 0000 0 0 4 &mpic 7 1
+ 0000 0x0 0x0 0x1 &mpic 0x4 0x1
+ 0000 0x0 0x0 0x2 &mpic 0x5 0x1
+ 0000 0x0 0x0 0x3 &mpic 0x6 0x1
+ 0000 0x0 0x0 0x4 &mpic 0x7 0x1
>;
pcie@0 {
- reg = <0 0 0 0 0>;
+ reg = <0x0 0x0 0x0 0x0 0x0>;
#size-cells = <2>;
#address-cells = <3>;
device_type = "pci";
- ranges = <02000000 0 80000000
- 02000000 0 80000000
- 0 20000000
+ ranges = <0x2000000 0x0 0x80000000
+ 0x2000000 0x0 0x80000000
+ 0x0 0x20000000
- 01000000 0 00000000
- 01000000 0 00000000
- 0 00010000>;
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x10000>;
};
};
#interrupt-cells = <1>;
#size-cells = <2>;
#address-cells = <3>;
- reg = <e000a000 1000>;
- bus-range = <0 ff>;
- ranges = <02000000 0 a0000000 a0000000 0 10000000
- 01000000 0 00000000 e1020000 0 00010000>;
- clock-frequency = <1fca055>;
+ reg = <0xe000a000 0x1000>;
+ bus-range = <0 255>;
+ ranges = <0x2000000 0x0 0xa0000000 0xa0000000 0x0 0x10000000
+ 0x1000000 0x0 0x0 0xe1020000 0x0 0x10000>;
+ clock-frequency = <33333333>;
interrupt-parent = <&mpic>;
- interrupts = <19 2>;
- interrupt-map-mask = <f800 0 0 7>;
+ interrupts = <25 2>;
+ interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
interrupt-map = <
/* IDSEL 0x0 */
- 0000 0 0 1 &mpic 0 1
- 0000 0 0 2 &mpic 1 1
- 0000 0 0 3 &mpic 2 1
- 0000 0 0 4 &mpic 3 1
+ 0000 0x0 0x0 0x1 &mpic 0x0 0x1
+ 0000 0x0 0x0 0x2 &mpic 0x1 0x1
+ 0000 0x0 0x0 0x3 &mpic 0x2 0x1
+ 0000 0x0 0x0 0x4 &mpic 0x3 0x1
>;
pcie@0 {
- reg = <0 0 0 0 0>;
+ reg = <0x0 0x0 0x0 0x0 0x0>;
#size-cells = <2>;
#address-cells = <3>;
device_type = "pci";
- ranges = <02000000 0 a0000000
- 02000000 0 a0000000
- 0 10000000
+ ranges = <0x2000000 0x0 0xa0000000
+ 0x2000000 0x0 0xa0000000
+ 0x0 0x10000000
- 01000000 0 00000000
- 01000000 0 00000000
- 0 00010000>;
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x10000>;
};
};
#interrupt-cells = <1>;
#size-cells = <2>;
#address-cells = <3>;
- reg = <e000b000 1000>;
- bus-range = <0 ff>;
- ranges = <02000000 0 b0000000 b0000000 0 00100000
- 01000000 0 00000000 b0100000 0 00100000>;
- clock-frequency = <1fca055>;
+ reg = <0xe000b000 0x1000>;
+ bus-range = <0 255>;
+ ranges = <0x2000000 0x0 0xb0000000 0xb0000000 0x0 0x100000
+ 0x1000000 0x0 0x0 0xb0100000 0x0 0x100000>;
+ clock-frequency = <33333333>;
interrupt-parent = <&mpic>;
- interrupts = <1b 2>;
- interrupt-map-mask = <ff00 0 0 1>;
+ interrupts = <27 2>;
+ interrupt-map-mask = <0xff00 0x0 0x0 0x1>;
interrupt-map = <
// IDSEL 0x1c USB
- e000 0 0 1 &i8259 c 2
- e100 0 0 2 &i8259 9 2
- e200 0 0 3 &i8259 a 2
- e300 0 0 4 &i8259 b 2
+ 0xe000 0x0 0x0 0x1 &i8259 0xc 0x2
+ 0xe100 0x0 0x0 0x2 &i8259 0x9 0x2
+ 0xe200 0x0 0x0 0x3 &i8259 0xa 0x2
+ 0xe300 0x0 0x0 0x4 &i8259 0xb 0x2
// IDSEL 0x1d Audio
- e800 0 0 1 &i8259 6 2
+ 0xe800 0x0 0x0 0x1 &i8259 0x6 0x2
// IDSEL 0x1e Legacy
- f000 0 0 1 &i8259 7 2
- f100 0 0 1 &i8259 7 2
+ 0xf000 0x0 0x0 0x1 &i8259 0x7 0x2
+ 0xf100 0x0 0x0 0x1 &i8259 0x7 0x2
// IDSEL 0x1f IDE/SATA
- f800 0 0 1 &i8259 e 2
- f900 0 0 1 &i8259 5 2
+ 0xf800 0x0 0x0 0x1 &i8259 0xe 0x2
+ 0xf900 0x0 0x0 0x1 &i8259 0x5 0x2
>;
pcie@0 {
- reg = <0 0 0 0 0>;
+ reg = <0x0 0x0 0x0 0x0 0x0>;
#size-cells = <2>;
#address-cells = <3>;
device_type = "pci";
- ranges = <02000000 0 b0000000
- 02000000 0 b0000000
- 0 00100000
+ ranges = <0x2000000 0x0 0xb0000000
+ 0x2000000 0x0 0xb0000000
+ 0x0 0x100000
- 01000000 0 00000000
- 01000000 0 00000000
- 0 00100000>;
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x100000>;
uli1575@0 {
- reg = <0 0 0 0 0>;
+ reg = <0x0 0x0 0x0 0x0 0x0>;
#size-cells = <2>;
#address-cells = <3>;
- ranges = <02000000 0 b0000000
- 02000000 0 b0000000
- 0 00100000
+ ranges = <0x2000000 0x0 0xb0000000
+ 0x2000000 0x0 0xb0000000
+ 0x0 0x100000
- 01000000 0 00000000
- 01000000 0 00000000
- 0 00100000>;
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x100000>;
isa@1e {
device_type = "isa";
#interrupt-cells = <2>;
#size-cells = <1>;
#address-cells = <2>;
- reg = <f000 0 0 0 0>;
- ranges = <1 0
- 01000000 0 0
- 00001000>;
+ reg = <0xf000 0x0 0x0 0x0 0x0>;
+ ranges = <0x1 0x0
+ 0x1000000 0x0 0x0
+ 0x1000>;
interrupt-parent = <&i8259>;
i8259: interrupt-controller@20 {
- reg = <1 20 2
- 1 a0 2
- 1 4d0 2>;
+ reg = <0x1 0x20 0x2
+ 0x1 0xa0 0x2
+ 0x1 0x4d0 0x2>;
interrupt-controller;
device_type = "interrupt-controller";
#address-cells = <0>;
i8042@60 {
#size-cells = <0>;
#address-cells = <1>;
- reg = <1 60 1 1 64 1>;
- interrupts = <1 3 c 3>;
+ reg = <0x1 0x60 0x1 0x1 0x64 0x1>;
+ interrupts = <1 3 12 3>;
interrupt-parent = <&i8259>;
keyboard@0 {
- reg = <0>;
+ reg = <0x0>;
compatible = "pnpPNP,303";
};
mouse@1 {
- reg = <1>;
+ reg = <0x1>;
compatible = "pnpPNP,f03";
};
};
rtc@70 {
compatible = "pnpPNP,b00";
- reg = <1 70 2>;
+ reg = <0x1 0x70 0x2>;
};
gpio@400 {
- reg = <1 400 80>;
+ reg = <0x1 0x400 0x80>;
};
};
};
/*
* MPC8548 CDS Device Tree Source
*
- * Copyright 2006 Freescale Semiconductor Inc.
+ * Copyright 2006, 2008 Freescale Semiconductor Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* option) any later version.
*/
+/dts-v1/;
/ {
model = "MPC8548CDS";
PowerPC,8548@0 {
device_type = "cpu";
- reg = <0>;
- d-cache-line-size = <20>; // 32 bytes
- i-cache-line-size = <20>; // 32 bytes
- d-cache-size = <8000>; // L1, 32K
- i-cache-size = <8000>; // L1, 32K
+ reg = <0x0>;
+ d-cache-line-size = <32>; // 32 bytes
+ i-cache-line-size = <32>; // 32 bytes
+ d-cache-size = <0x8000>; // L1, 32K
+ i-cache-size = <0x8000>; // L1, 32K
timebase-frequency = <0>; // 33 MHz, from uboot
bus-frequency = <0>; // 166 MHz
clock-frequency = <0>; // 825 MHz, from uboot
memory {
device_type = "memory";
- reg = <00000000 08000000>; // 128M at 0x0
+ reg = <0x0 0x8000000>; // 128M at 0x0
};
soc8548@e0000000 {
#address-cells = <1>;
#size-cells = <1>;
device_type = "soc";
- ranges = <00000000 e0000000 00100000>;
- reg = <e0000000 00001000>; // CCSRBAR
+ ranges = <0x0 0xe0000000 0x100000>;
+ reg = <0xe0000000 0x1000>; // CCSRBAR
bus-frequency = <0>;
memory-controller@2000 {
compatible = "fsl,8548-memory-controller";
- reg = <2000 1000>;
+ reg = <0x2000 0x1000>;
interrupt-parent = <&mpic>;
- interrupts = <12 2>;
+ interrupts = <18 2>;
};
l2-cache-controller@20000 {
compatible = "fsl,8548-l2-cache-controller";
- reg = <20000 1000>;
- cache-line-size = <20>; // 32 bytes
- cache-size = <80000>; // L2, 512K
+ reg = <0x20000 0x1000>;
+ cache-line-size = <32>; // 32 bytes
+ cache-size = <0x80000>; // L2, 512K
interrupt-parent = <&mpic>;
- interrupts = <10 2>;
+ interrupts = <16 2>;
};
i2c@3000 {
#size-cells = <0>;
cell-index = <0>;
compatible = "fsl-i2c";
- reg = <3000 100>;
- interrupts = <2b 2>;
+ reg = <0x3000 0x100>;
+ interrupts = <43 2>;
interrupt-parent = <&mpic>;
dfsrr;
};
#size-cells = <0>;
cell-index = <1>;
compatible = "fsl-i2c";
- reg = <3100 100>;
- interrupts = <2b 2>;
+ reg = <0x3100 0x100>;
+ interrupts = <43 2>;
interrupt-parent = <&mpic>;
dfsrr;
};
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,gianfar-mdio";
- reg = <24520 20>;
+ reg = <0x24520 0x20>;
phy0: ethernet-phy@0 {
interrupt-parent = <&mpic>;
interrupts = <5 1>;
- reg = <0>;
+ reg = <0x0>;
device_type = "ethernet-phy";
};
phy1: ethernet-phy@1 {
interrupt-parent = <&mpic>;
interrupts = <5 1>;
- reg = <1>;
+ reg = <0x1>;
device_type = "ethernet-phy";
};
phy2: ethernet-phy@2 {
interrupt-parent = <&mpic>;
interrupts = <5 1>;
- reg = <2>;
+ reg = <0x2>;
device_type = "ethernet-phy";
};
phy3: ethernet-phy@3 {
interrupt-parent = <&mpic>;
interrupts = <5 1>;
- reg = <3>;
+ reg = <0x3>;
device_type = "ethernet-phy";
};
};
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
- reg = <24000 1000>;
+ reg = <0x24000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <1d 2 1e 2 22 2>;
+ interrupts = <29 2 30 2 34 2>;
interrupt-parent = <&mpic>;
phy-handle = <&phy0>;
};
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
- reg = <25000 1000>;
+ reg = <0x25000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <23 2 24 2 28 2>;
+ interrupts = <35 2 36 2 40 2>;
interrupt-parent = <&mpic>;
phy-handle = <&phy1>;
};
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
- reg = <26000 1000>;
+ reg = <0x26000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <1f 2 20 2 21 2>;
+ interrupts = <31 2 32 2 33 2>;
interrupt-parent = <&mpic>;
phy-handle = <&phy2>;
};
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
- reg = <27000 1000>;
+ reg = <0x27000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <25 2 26 2 27 2>;
+ interrupts = <37 2 38 2 39 2>;
interrupt-parent = <&mpic>;
phy-handle = <&phy3>;
};
cell-index = <0>;
device_type = "serial";
compatible = "ns16550";
- reg = <4500 100>; // reg base, size
+ reg = <0x4500 0x100>; // reg base, size
clock-frequency = <0>; // should we fill in in uboot?
- interrupts = <2a 2>;
+ interrupts = <42 2>;
interrupt-parent = <&mpic>;
};
cell-index = <1>;
device_type = "serial";
compatible = "ns16550";
- reg = <4600 100>; // reg base, size
+ reg = <0x4600 0x100>; // reg base, size
clock-frequency = <0>; // should we fill in in uboot?
- interrupts = <2a 2>;
+ interrupts = <42 2>;
interrupt-parent = <&mpic>;
};
global-utilities@e0000 { //global utilities reg
compatible = "fsl,mpc8548-guts";
- reg = <e0000 1000>;
+ reg = <0xe0000 0x1000>;
fsl,has-rstcr;
};
interrupt-controller;
#address-cells = <0>;
#interrupt-cells = <2>;
- reg = <40000 40000>;
+ reg = <0x40000 0x40000>;
compatible = "chrp,open-pic";
device_type = "open-pic";
big-endian;
pci0: pci@e0008000 {
cell-index = <0>;
- interrupt-map-mask = <f800 0 0 7>;
+ interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
interrupt-map = <
/* IDSEL 0x4 (PCIX Slot 2) */
- 02000 0 0 1 &mpic 0 1
- 02000 0 0 2 &mpic 1 1
- 02000 0 0 3 &mpic 2 1
- 02000 0 0 4 &mpic 3 1
+ 0x2000 0x0 0x0 0x1 &mpic 0x0 0x1
+ 0x2000 0x0 0x0 0x2 &mpic 0x1 0x1
+ 0x2000 0x0 0x0 0x3 &mpic 0x2 0x1
+ 0x2000 0x0 0x0 0x4 &mpic 0x3 0x1
/* IDSEL 0x5 (PCIX Slot 3) */
- 02800 0 0 1 &mpic 1 1
- 02800 0 0 2 &mpic 2 1
- 02800 0 0 3 &mpic 3 1
- 02800 0 0 4 &mpic 0 1
+ 0x2800 0x0 0x0 0x1 &mpic 0x1 0x1
+ 0x2800 0x0 0x0 0x2 &mpic 0x2 0x1
+ 0x2800 0x0 0x0 0x3 &mpic 0x3 0x1
+ 0x2800 0x0 0x0 0x4 &mpic 0x0 0x1
/* IDSEL 0x6 (PCIX Slot 4) */
- 03000 0 0 1 &mpic 2 1
- 03000 0 0 2 &mpic 3 1
- 03000 0 0 3 &mpic 0 1
- 03000 0 0 4 &mpic 1 1
+ 0x3000 0x0 0x0 0x1 &mpic 0x2 0x1
+ 0x3000 0x0 0x0 0x2 &mpic 0x3 0x1
+ 0x3000 0x0 0x0 0x3 &mpic 0x0 0x1
+ 0x3000 0x0 0x0 0x4 &mpic 0x1 0x1
/* IDSEL 0x8 (PCIX Slot 5) */
- 04000 0 0 1 &mpic 0 1
- 04000 0 0 2 &mpic 1 1
- 04000 0 0 3 &mpic 2 1
- 04000 0 0 4 &mpic 3 1
+ 0x4000 0x0 0x0 0x1 &mpic 0x0 0x1
+ 0x4000 0x0 0x0 0x2 &mpic 0x1 0x1
+ 0x4000 0x0 0x0 0x3 &mpic 0x2 0x1
+ 0x4000 0x0 0x0 0x4 &mpic 0x3 0x1
/* IDSEL 0xC (Tsi310 bridge) */
- 06000 0 0 1 &mpic 0 1
- 06000 0 0 2 &mpic 1 1
- 06000 0 0 3 &mpic 2 1
- 06000 0 0 4 &mpic 3 1
+ 0x6000 0x0 0x0 0x1 &mpic 0x0 0x1
+ 0x6000 0x0 0x0 0x2 &mpic 0x1 0x1
+ 0x6000 0x0 0x0 0x3 &mpic 0x2 0x1
+ 0x6000 0x0 0x0 0x4 &mpic 0x3 0x1
/* IDSEL 0x14 (Slot 2) */
- 0a000 0 0 1 &mpic 0 1
- 0a000 0 0 2 &mpic 1 1
- 0a000 0 0 3 &mpic 2 1
- 0a000 0 0 4 &mpic 3 1
+ 0xa000 0x0 0x0 0x1 &mpic 0x0 0x1
+ 0xa000 0x0 0x0 0x2 &mpic 0x1 0x1
+ 0xa000 0x0 0x0 0x3 &mpic 0x2 0x1
+ 0xa000 0x0 0x0 0x4 &mpic 0x3 0x1
/* IDSEL 0x15 (Slot 3) */
- 0a800 0 0 1 &mpic 1 1
- 0a800 0 0 2 &mpic 2 1
- 0a800 0 0 3 &mpic 3 1
- 0a800 0 0 4 &mpic 0 1
+ 0xa800 0x0 0x0 0x1 &mpic 0x1 0x1
+ 0xa800 0x0 0x0 0x2 &mpic 0x2 0x1
+ 0xa800 0x0 0x0 0x3 &mpic 0x3 0x1
+ 0xa800 0x0 0x0 0x4 &mpic 0x0 0x1
/* IDSEL 0x16 (Slot 4) */
- 0b000 0 0 1 &mpic 2 1
- 0b000 0 0 2 &mpic 3 1
- 0b000 0 0 3 &mpic 0 1
- 0b000 0 0 4 &mpic 1 1
+ 0xb000 0x0 0x0 0x1 &mpic 0x2 0x1
+ 0xb000 0x0 0x0 0x2 &mpic 0x3 0x1
+ 0xb000 0x0 0x0 0x3 &mpic 0x0 0x1
+ 0xb000 0x0 0x0 0x4 &mpic 0x1 0x1
/* IDSEL 0x18 (Slot 5) */
- 0c000 0 0 1 &mpic 0 1
- 0c000 0 0 2 &mpic 1 1
- 0c000 0 0 3 &mpic 2 1
- 0c000 0 0 4 &mpic 3 1
+ 0xc000 0x0 0x0 0x1 &mpic 0x0 0x1
+ 0xc000 0x0 0x0 0x2 &mpic 0x1 0x1
+ 0xc000 0x0 0x0 0x3 &mpic 0x2 0x1
+ 0xc000 0x0 0x0 0x4 &mpic 0x3 0x1
/* IDSEL 0x1C (Tsi310 bridge PCI primary) */
- 0E000 0 0 1 &mpic 0 1
- 0E000 0 0 2 &mpic 1 1
- 0E000 0 0 3 &mpic 2 1
- 0E000 0 0 4 &mpic 3 1>;
+ 0xe000 0x0 0x0 0x1 &mpic 0x0 0x1
+ 0xe000 0x0 0x0 0x2 &mpic 0x1 0x1
+ 0xe000 0x0 0x0 0x3 &mpic 0x2 0x1
+ 0xe000 0x0 0x0 0x4 &mpic 0x3 0x1>;
interrupt-parent = <&mpic>;
- interrupts = <18 2>;
+ interrupts = <24 2>;
bus-range = <0 0>;
- ranges = <02000000 0 80000000 80000000 0 10000000
- 01000000 0 00000000 e2000000 0 00800000>;
- clock-frequency = <3f940aa>;
+ ranges = <0x2000000 0x0 0x80000000 0x80000000 0x0 0x10000000
+ 0x1000000 0x0 0x0 0xe2000000 0x0 0x800000>;
+ clock-frequency = <66666666>;
#interrupt-cells = <1>;
#size-cells = <2>;
#address-cells = <3>;
- reg = <e0008000 1000>;
+ reg = <0xe0008000 0x1000>;
compatible = "fsl,mpc8540-pcix", "fsl,mpc8540-pci";
device_type = "pci";
pci_bridge@1c {
- interrupt-map-mask = <f800 0 0 7>;
+ interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
interrupt-map = <
/* IDSEL 0x00 (PrPMC Site) */
- 0000 0 0 1 &mpic 0 1
- 0000 0 0 2 &mpic 1 1
- 0000 0 0 3 &mpic 2 1
- 0000 0 0 4 &mpic 3 1
+ 0000 0x0 0x0 0x1 &mpic 0x0 0x1
+ 0000 0x0 0x0 0x2 &mpic 0x1 0x1
+ 0000 0x0 0x0 0x3 &mpic 0x2 0x1
+ 0000 0x0 0x0 0x4 &mpic 0x3 0x1
/* IDSEL 0x04 (VIA chip) */
- 2000 0 0 1 &mpic 0 1
- 2000 0 0 2 &mpic 1 1
- 2000 0 0 3 &mpic 2 1
- 2000 0 0 4 &mpic 3 1
+ 0x2000 0x0 0x0 0x1 &mpic 0x0 0x1
+ 0x2000 0x0 0x0 0x2 &mpic 0x1 0x1
+ 0x2000 0x0 0x0 0x3 &mpic 0x2 0x1
+ 0x2000 0x0 0x0 0x4 &mpic 0x3 0x1
/* IDSEL 0x05 (8139) */
- 2800 0 0 1 &mpic 1 1
+ 0x2800 0x0 0x0 0x1 &mpic 0x1 0x1
/* IDSEL 0x06 (Slot 6) */
- 3000 0 0 1 &mpic 2 1
- 3000 0 0 2 &mpic 3 1
- 3000 0 0 3 &mpic 0 1
- 3000 0 0 4 &mpic 1 1
+ 0x3000 0x0 0x0 0x1 &mpic 0x2 0x1
+ 0x3000 0x0 0x0 0x2 &mpic 0x3 0x1
+ 0x3000 0x0 0x0 0x3 &mpic 0x0 0x1
+ 0x3000 0x0 0x0 0x4 &mpic 0x1 0x1
/* IDESL 0x07 (Slot 7) */
- 3800 0 0 1 &mpic 3 1
- 3800 0 0 2 &mpic 0 1
- 3800 0 0 3 &mpic 1 1
- 3800 0 0 4 &mpic 2 1>;
+ 0x3800 0x0 0x0 0x1 &mpic 0x3 0x1
+ 0x3800 0x0 0x0 0x2 &mpic 0x0 0x1
+ 0x3800 0x0 0x0 0x3 &mpic 0x1 0x1
+ 0x3800 0x0 0x0 0x4 &mpic 0x2 0x1>;
- reg = <e000 0 0 0 0>;
+ reg = <0xe000 0x0 0x0 0x0 0x0>;
#interrupt-cells = <1>;
#size-cells = <2>;
#address-cells = <3>;
- ranges = <02000000 0 80000000
- 02000000 0 80000000
- 0 20000000
- 01000000 0 00000000
- 01000000 0 00000000
- 0 00080000>;
- clock-frequency = <1fca055>;
+ ranges = <0x2000000 0x0 0x80000000
+ 0x2000000 0x0 0x80000000
+ 0x0 0x20000000
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x80000>;
+ clock-frequency = <33333333>;
isa@4 {
device_type = "isa";
#interrupt-cells = <2>;
#size-cells = <1>;
#address-cells = <2>;
- reg = <2000 0 0 0 0>;
- ranges = <1 0 01000000 0 0 00001000>;
+ reg = <0x2000 0x0 0x0 0x0 0x0>;
+ ranges = <0x1 0x0 0x1000000 0x0 0x0 0x1000>;
interrupt-parent = <&i8259>;
i8259: interrupt-controller@20 {
interrupt-controller;
device_type = "interrupt-controller";
- reg = <1 20 2
- 1 a0 2
- 1 4d0 2>;
+ reg = <0x1 0x20 0x2
+ 0x1 0xa0 0x2
+ 0x1 0x4d0 0x2>;
#address-cells = <0>;
#interrupt-cells = <2>;
compatible = "chrp,iic";
rtc@70 {
compatible = "pnpPNP,b00";
- reg = <1 70 2>;
+ reg = <0x1 0x70 0x2>;
};
};
};
pci1: pci@e0009000 {
cell-index = <1>;
- interrupt-map-mask = <f800 0 0 7>;
+ interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
interrupt-map = <
/* IDSEL 0x15 */
- a800 0 0 1 &mpic b 1
- a800 0 0 2 &mpic 1 1
- a800 0 0 3 &mpic 2 1
- a800 0 0 4 &mpic 3 1>;
+ 0xa800 0x0 0x0 0x1 &mpic 0xb 0x1
+ 0xa800 0x0 0x0 0x2 &mpic 0x1 0x1
+ 0xa800 0x0 0x0 0x3 &mpic 0x2 0x1
+ 0xa800 0x0 0x0 0x4 &mpic 0x3 0x1>;
interrupt-parent = <&mpic>;
- interrupts = <19 2>;
+ interrupts = <25 2>;
bus-range = <0 0>;
- ranges = <02000000 0 90000000 90000000 0 10000000
- 01000000 0 00000000 e2800000 0 00800000>;
- clock-frequency = <3f940aa>;
+ ranges = <0x2000000 0x0 0x90000000 0x90000000 0x0 0x10000000
+ 0x1000000 0x0 0x0 0xe2800000 0x0 0x800000>;
+ clock-frequency = <66666666>;
#interrupt-cells = <1>;
#size-cells = <2>;
#address-cells = <3>;
- reg = <e0009000 1000>;
+ reg = <0xe0009000 0x1000>;
compatible = "fsl,mpc8540-pci";
device_type = "pci";
};
pci2: pcie@e000a000 {
cell-index = <2>;
- interrupt-map-mask = <f800 0 0 7>;
+ interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
interrupt-map = <
/* IDSEL 0x0 (PEX) */
- 00000 0 0 1 &mpic 0 1
- 00000 0 0 2 &mpic 1 1
- 00000 0 0 3 &mpic 2 1
- 00000 0 0 4 &mpic 3 1>;
+ 00000 0x0 0x0 0x1 &mpic 0x0 0x1
+ 00000 0x0 0x0 0x2 &mpic 0x1 0x1
+ 00000 0x0 0x0 0x3 &mpic 0x2 0x1
+ 00000 0x0 0x0 0x4 &mpic 0x3 0x1>;
interrupt-parent = <&mpic>;
- interrupts = <1a 2>;
- bus-range = <0 ff>;
- ranges = <02000000 0 a0000000 a0000000 0 20000000
- 01000000 0 00000000 e3000000 0 08000000>;
- clock-frequency = <1fca055>;
+ interrupts = <26 2>;
+ bus-range = <0 255>;
+ ranges = <0x2000000 0x0 0xa0000000 0xa0000000 0x0 0x20000000
+ 0x1000000 0x0 0x0 0xe3000000 0x0 0x8000000>;
+ clock-frequency = <33333333>;
#interrupt-cells = <1>;
#size-cells = <2>;
#address-cells = <3>;
- reg = <e000a000 1000>;
+ reg = <0xe000a000 0x1000>;
compatible = "fsl,mpc8548-pcie";
device_type = "pci";
pcie@0 {
- reg = <0 0 0 0 0>;
+ reg = <0x0 0x0 0x0 0x0 0x0>;
#size-cells = <2>;
#address-cells = <3>;
device_type = "pci";
- ranges = <02000000 0 a0000000
- 02000000 0 a0000000
- 0 20000000
+ ranges = <0x2000000 0x0 0xa0000000
+ 0x2000000 0x0 0xa0000000
+ 0x0 0x20000000
- 01000000 0 00000000
- 01000000 0 00000000
- 0 08000000>;
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x8000000>;
};
};
};
/*
* MPC8555 CDS Device Tree Source
*
- * Copyright 2006 Freescale Semiconductor Inc.
+ * Copyright 2006, 2008 Freescale Semiconductor Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* option) any later version.
*/
+/dts-v1/;
/ {
model = "MPC8555CDS";
PowerPC,8555@0 {
device_type = "cpu";
- reg = <0>;
- d-cache-line-size = <20>; // 32 bytes
- i-cache-line-size = <20>; // 32 bytes
- d-cache-size = <8000>; // L1, 32K
- i-cache-size = <8000>; // L1, 32K
+ reg = <0x0>;
+ d-cache-line-size = <32>; // 32 bytes
+ i-cache-line-size = <32>; // 32 bytes
+ d-cache-size = <0x8000>; // L1, 32K
+ i-cache-size = <0x8000>; // L1, 32K
timebase-frequency = <0>; // 33 MHz, from uboot
bus-frequency = <0>; // 166 MHz
clock-frequency = <0>; // 825 MHz, from uboot
memory {
device_type = "memory";
- reg = <00000000 08000000>; // 128M at 0x0
+ reg = <0x0 0x8000000>; // 128M at 0x0
};
soc8555@e0000000 {
#address-cells = <1>;
#size-cells = <1>;
device_type = "soc";
- ranges = <0 e0000000 00100000>;
- reg = <e0000000 00001000>; // CCSRBAR 1M
+ ranges = <0x0 0xe0000000 0x100000>;
+ reg = <0xe0000000 0x1000>; // CCSRBAR 1M
bus-frequency = <0>;
memory-controller@2000 {
compatible = "fsl,8555-memory-controller";
- reg = <2000 1000>;
+ reg = <0x2000 0x1000>;
interrupt-parent = <&mpic>;
- interrupts = <12 2>;
+ interrupts = <18 2>;
};
l2-cache-controller@20000 {
compatible = "fsl,8555-l2-cache-controller";
- reg = <20000 1000>;
- cache-line-size = <20>; // 32 bytes
- cache-size = <40000>; // L2, 256K
+ reg = <0x20000 0x1000>;
+ cache-line-size = <32>; // 32 bytes
+ cache-size = <0x40000>; // L2, 256K
interrupt-parent = <&mpic>;
- interrupts = <10 2>;
+ interrupts = <16 2>;
};
i2c@3000 {
#size-cells = <0>;
cell-index = <0>;
compatible = "fsl-i2c";
- reg = <3000 100>;
- interrupts = <2b 2>;
+ reg = <0x3000 0x100>;
+ interrupts = <43 2>;
interrupt-parent = <&mpic>;
dfsrr;
};
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,gianfar-mdio";
- reg = <24520 20>;
+ reg = <0x24520 0x20>;
phy0: ethernet-phy@0 {
interrupt-parent = <&mpic>;
interrupts = <5 1>;
- reg = <0>;
+ reg = <0x0>;
device_type = "ethernet-phy";
};
phy1: ethernet-phy@1 {
interrupt-parent = <&mpic>;
interrupts = <5 1>;
- reg = <1>;
+ reg = <0x1>;
device_type = "ethernet-phy";
};
};
device_type = "network";
model = "TSEC";
compatible = "gianfar";
- reg = <24000 1000>;
+ reg = <0x24000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <1d 2 1e 2 22 2>;
+ interrupts = <29 2 30 2 34 2>;
interrupt-parent = <&mpic>;
phy-handle = <&phy0>;
};
device_type = "network";
model = "TSEC";
compatible = "gianfar";
- reg = <25000 1000>;
+ reg = <0x25000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <23 2 24 2 28 2>;
+ interrupts = <35 2 36 2 40 2>;
interrupt-parent = <&mpic>;
phy-handle = <&phy1>;
};
cell-index = <0>;
device_type = "serial";
compatible = "ns16550";
- reg = <4500 100>; // reg base, size
+ reg = <0x4500 0x100>; // reg base, size
clock-frequency = <0>; // should we fill in in uboot?
- interrupts = <2a 2>;
+ interrupts = <42 2>;
interrupt-parent = <&mpic>;
};
cell-index = <1>;
device_type = "serial";
compatible = "ns16550";
- reg = <4600 100>; // reg base, size
+ reg = <0x4600 0x100>; // reg base, size
clock-frequency = <0>; // should we fill in in uboot?
- interrupts = <2a 2>;
+ interrupts = <42 2>;
interrupt-parent = <&mpic>;
};
interrupt-controller;
#address-cells = <0>;
#interrupt-cells = <2>;
- reg = <40000 40000>;
+ reg = <0x40000 0x40000>;
compatible = "chrp,open-pic";
device_type = "open-pic";
big-endian;
#address-cells = <1>;
#size-cells = <1>;
compatible = "fsl,mpc8555-cpm", "fsl,cpm2";
- reg = <919c0 30>;
+ reg = <0x919c0 0x30>;
ranges;
muram@80000 {
#address-cells = <1>;
#size-cells = <1>;
- ranges = <0 80000 10000>;
+ ranges = <0x0 0x80000 0x10000>;
data@0 {
compatible = "fsl,cpm-muram-data";
- reg = <0 2000 9000 1000>;
+ reg = <0x0 0x2000 0x9000 0x1000>;
};
};
compatible = "fsl,mpc8555-brg",
"fsl,cpm2-brg",
"fsl,cpm-brg";
- reg = <919f0 10 915f0 10>;
+ reg = <0x919f0 0x10 0x915f0 0x10>;
};
cpmpic: pic@90c00 {
interrupt-controller;
#address-cells = <0>;
#interrupt-cells = <2>;
- interrupts = <2e 2>;
+ interrupts = <46 2>;
interrupt-parent = <&mpic>;
- reg = <90c00 80>;
+ reg = <0x90c00 0x80>;
compatible = "fsl,mpc8555-cpm-pic", "fsl,cpm2-pic";
};
};
pci0: pci@e0008000 {
cell-index = <0>;
- interrupt-map-mask = <1f800 0 0 7>;
+ interrupt-map-mask = <0x1f800 0x0 0x0 0x7>;
interrupt-map = <
/* IDSEL 0x10 */
- 08000 0 0 1 &mpic 0 1
- 08000 0 0 2 &mpic 1 1
- 08000 0 0 3 &mpic 2 1
- 08000 0 0 4 &mpic 3 1
+ 0x8000 0x0 0x0 0x1 &mpic 0x0 0x1
+ 0x8000 0x0 0x0 0x2 &mpic 0x1 0x1
+ 0x8000 0x0 0x0 0x3 &mpic 0x2 0x1
+ 0x8000 0x0 0x0 0x4 &mpic 0x3 0x1
/* IDSEL 0x11 */
- 08800 0 0 1 &mpic 0 1
- 08800 0 0 2 &mpic 1 1
- 08800 0 0 3 &mpic 2 1
- 08800 0 0 4 &mpic 3 1
+ 0x8800 0x0 0x0 0x1 &mpic 0x0 0x1
+ 0x8800 0x0 0x0 0x2 &mpic 0x1 0x1
+ 0x8800 0x0 0x0 0x3 &mpic 0x2 0x1
+ 0x8800 0x0 0x0 0x4 &mpic 0x3 0x1
/* IDSEL 0x12 (Slot 1) */
- 09000 0 0 1 &mpic 0 1
- 09000 0 0 2 &mpic 1 1
- 09000 0 0 3 &mpic 2 1
- 09000 0 0 4 &mpic 3 1
+ 0x9000 0x0 0x0 0x1 &mpic 0x0 0x1
+ 0x9000 0x0 0x0 0x2 &mpic 0x1 0x1
+ 0x9000 0x0 0x0 0x3 &mpic 0x2 0x1
+ 0x9000 0x0 0x0 0x4 &mpic 0x3 0x1
/* IDSEL 0x13 (Slot 2) */
- 09800 0 0 1 &mpic 1 1
- 09800 0 0 2 &mpic 2 1
- 09800 0 0 3 &mpic 3 1
- 09800 0 0 4 &mpic 0 1
+ 0x9800 0x0 0x0 0x1 &mpic 0x1 0x1
+ 0x9800 0x0 0x0 0x2 &mpic 0x2 0x1
+ 0x9800 0x0 0x0 0x3 &mpic 0x3 0x1
+ 0x9800 0x0 0x0 0x4 &mpic 0x0 0x1
/* IDSEL 0x14 (Slot 3) */
- 0a000 0 0 1 &mpic 2 1
- 0a000 0 0 2 &mpic 3 1
- 0a000 0 0 3 &mpic 0 1
- 0a000 0 0 4 &mpic 1 1
+ 0xa000 0x0 0x0 0x1 &mpic 0x2 0x1
+ 0xa000 0x0 0x0 0x2 &mpic 0x3 0x1
+ 0xa000 0x0 0x0 0x3 &mpic 0x0 0x1
+ 0xa000 0x0 0x0 0x4 &mpic 0x1 0x1
/* IDSEL 0x15 (Slot 4) */
- 0a800 0 0 1 &mpic 3 1
- 0a800 0 0 2 &mpic 0 1
- 0a800 0 0 3 &mpic 1 1
- 0a800 0 0 4 &mpic 2 1
+ 0xa800 0x0 0x0 0x1 &mpic 0x3 0x1
+ 0xa800 0x0 0x0 0x2 &mpic 0x0 0x1
+ 0xa800 0x0 0x0 0x3 &mpic 0x1 0x1
+ 0xa800 0x0 0x0 0x4 &mpic 0x2 0x1
/* Bus 1 (Tundra Bridge) */
/* IDSEL 0x12 (ISA bridge) */
- 19000 0 0 1 &mpic 0 1
- 19000 0 0 2 &mpic 1 1
- 19000 0 0 3 &mpic 2 1
- 19000 0 0 4 &mpic 3 1>;
+ 0x19000 0x0 0x0 0x1 &mpic 0x0 0x1
+ 0x19000 0x0 0x0 0x2 &mpic 0x1 0x1
+ 0x19000 0x0 0x0 0x3 &mpic 0x2 0x1
+ 0x19000 0x0 0x0 0x4 &mpic 0x3 0x1>;
interrupt-parent = <&mpic>;
- interrupts = <18 2>;
+ interrupts = <24 2>;
bus-range = <0 0>;
- ranges = <02000000 0 80000000 80000000 0 20000000
- 01000000 0 00000000 e2000000 0 00100000>;
- clock-frequency = <3f940aa>;
+ ranges = <0x2000000 0x0 0x80000000 0x80000000 0x0 0x20000000
+ 0x1000000 0x0 0x0 0xe2000000 0x0 0x100000>;
+ clock-frequency = <66666666>;
#interrupt-cells = <1>;
#size-cells = <2>;
#address-cells = <3>;
- reg = <e0008000 1000>;
+ reg = <0xe0008000 0x1000>;
compatible = "fsl,mpc8540-pci";
device_type = "pci";
i8259@19000 {
interrupt-controller;
device_type = "interrupt-controller";
- reg = <19000 0 0 0 1>;
+ reg = <0x19000 0x0 0x0 0x0 0x1>;
#address-cells = <0>;
#interrupt-cells = <2>;
compatible = "chrp,iic";
pci1: pci@e0009000 {
cell-index = <1>;
- interrupt-map-mask = <f800 0 0 7>;
+ interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
interrupt-map = <
/* IDSEL 0x15 */
- a800 0 0 1 &mpic b 1
- a800 0 0 2 &mpic b 1
- a800 0 0 3 &mpic b 1
- a800 0 0 4 &mpic b 1>;
+ 0xa800 0x0 0x0 0x1 &mpic 0xb 0x1
+ 0xa800 0x0 0x0 0x2 &mpic 0xb 0x1
+ 0xa800 0x0 0x0 0x3 &mpic 0xb 0x1
+ 0xa800 0x0 0x0 0x4 &mpic 0xb 0x1>;
interrupt-parent = <&mpic>;
- interrupts = <19 2>;
+ interrupts = <25 2>;
bus-range = <0 0>;
- ranges = <02000000 0 a0000000 a0000000 0 20000000
- 01000000 0 00000000 e3000000 0 00100000>;
- clock-frequency = <3f940aa>;
+ ranges = <0x2000000 0x0 0xa0000000 0xa0000000 0x0 0x20000000
+ 0x1000000 0x0 0x0 0xe3000000 0x0 0x100000>;
+ clock-frequency = <66666666>;
#interrupt-cells = <1>;
#size-cells = <2>;
#address-cells = <3>;
- reg = <e0009000 1000>;
+ reg = <0xe0009000 0x1000>;
compatible = "fsl,mpc8540-pci";
device_type = "pci";
};
/*
* MPC8560 ADS Device Tree Source
*
- * Copyright 2006 Freescale Semiconductor Inc.
+ * Copyright 2006, 2008 Freescale Semiconductor Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* option) any later version.
*/
+/dts-v1/;
/ {
model = "MPC8560ADS";
PowerPC,8560@0 {
device_type = "cpu";
- reg = <0>;
- d-cache-line-size = <20>; // 32 bytes
- i-cache-line-size = <20>; // 32 bytes
- d-cache-size = <8000>; // L1, 32K
- i-cache-size = <8000>; // L1, 32K
- timebase-frequency = <04ead9a0>;
- bus-frequency = <13ab6680>;
- clock-frequency = <312c8040>;
+ reg = <0x0>;
+ d-cache-line-size = <32>; // 32 bytes
+ i-cache-line-size = <32>; // 32 bytes
+ d-cache-size = <0x8000>; // L1, 32K
+ i-cache-size = <0x8000>; // L1, 32K
+ timebase-frequency = <82500000>;
+ bus-frequency = <330000000>;
+ clock-frequency = <825000000>;
};
};
memory {
device_type = "memory";
- reg = <00000000 10000000>;
+ reg = <0x0 0x10000000>;
};
soc8560@e0000000 {
#address-cells = <1>;
#size-cells = <1>;
device_type = "soc";
- ranges = <0 e0000000 00100000>;
- reg = <e0000000 00000200>;
- bus-frequency = <13ab6680>;
+ ranges = <0x0 0xe0000000 0x100000>;
+ reg = <0xe0000000 0x200>;
+ bus-frequency = <330000000>;
memory-controller@2000 {
compatible = "fsl,8540-memory-controller";
- reg = <2000 1000>;
+ reg = <0x2000 0x1000>;
interrupt-parent = <&mpic>;
- interrupts = <12 2>;
+ interrupts = <18 2>;
};
l2-cache-controller@20000 {
compatible = "fsl,8540-l2-cache-controller";
- reg = <20000 1000>;
- cache-line-size = <20>; // 32 bytes
- cache-size = <40000>; // L2, 256K
+ reg = <0x20000 0x1000>;
+ cache-line-size = <32>; // 32 bytes
+ cache-size = <0x40000>; // L2, 256K
interrupt-parent = <&mpic>;
- interrupts = <10 2>;
+ interrupts = <16 2>;
};
mdio@24520 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,gianfar-mdio";
- reg = <24520 20>;
+ reg = <0x24520 0x20>;
phy0: ethernet-phy@0 {
interrupt-parent = <&mpic>;
interrupts = <5 1>;
- reg = <0>;
+ reg = <0x0>;
device_type = "ethernet-phy";
};
phy1: ethernet-phy@1 {
interrupt-parent = <&mpic>;
interrupts = <5 1>;
- reg = <1>;
+ reg = <0x1>;
device_type = "ethernet-phy";
};
phy2: ethernet-phy@2 {
interrupt-parent = <&mpic>;
interrupts = <7 1>;
- reg = <2>;
+ reg = <0x2>;
device_type = "ethernet-phy";
};
phy3: ethernet-phy@3 {
interrupt-parent = <&mpic>;
interrupts = <7 1>;
- reg = <3>;
+ reg = <0x3>;
device_type = "ethernet-phy";
};
};
device_type = "network";
model = "TSEC";
compatible = "gianfar";
- reg = <24000 1000>;
+ reg = <0x24000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <1d 2 1e 2 22 2>;
+ interrupts = <29 2 30 2 34 2>;
interrupt-parent = <&mpic>;
phy-handle = <&phy0>;
};
device_type = "network";
model = "TSEC";
compatible = "gianfar";
- reg = <25000 1000>;
+ reg = <0x25000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <23 2 24 2 28 2>;
+ interrupts = <35 2 36 2 40 2>;
interrupt-parent = <&mpic>;
phy-handle = <&phy1>;
};
interrupt-controller;
#address-cells = <0>;
#interrupt-cells = <2>;
- reg = <40000 40000>;
+ reg = <0x40000 0x40000>;
device_type = "open-pic";
};
#address-cells = <1>;
#size-cells = <1>;
compatible = "fsl,mpc8560-cpm", "fsl,cpm2";
- reg = <919c0 30>;
+ reg = <0x919c0 0x30>;
ranges;
muram@80000 {
#address-cells = <1>;
#size-cells = <1>;
- ranges = <0 80000 10000>;
+ ranges = <0x0 0x80000 0x10000>;
data@0 {
compatible = "fsl,cpm-muram-data";
- reg = <0 4000 9000 2000>;
+ reg = <0x0 0x4000 0x9000 0x2000>;
};
};
compatible = "fsl,mpc8560-brg",
"fsl,cpm2-brg",
"fsl,cpm-brg";
- reg = <919f0 10 915f0 10>;
- clock-frequency = <d#165000000>;
+ reg = <0x919f0 0x10 0x915f0 0x10>;
+ clock-frequency = <165000000>;
};
cpmpic: pic@90c00 {
interrupt-controller;
#address-cells = <0>;
#interrupt-cells = <2>;
- interrupts = <2e 2>;
+ interrupts = <46 2>;
interrupt-parent = <&mpic>;
- reg = <90c00 80>;
+ reg = <0x90c00 0x80>;
compatible = "fsl,mpc8560-cpm-pic", "fsl,cpm2-pic";
};
device_type = "serial";
compatible = "fsl,mpc8560-scc-uart",
"fsl,cpm2-scc-uart";
- reg = <91a00 20 88000 100>;
+ reg = <0x91a00 0x20 0x88000 0x100>;
fsl,cpm-brg = <1>;
- fsl,cpm-command = <00800000>;
- current-speed = <1c200>;
- interrupts = <28 8>;
+ fsl,cpm-command = <0x800000>;
+ current-speed = <115200>;
+ interrupts = <40 8>;
interrupt-parent = <&cpmpic>;
};
device_type = "serial";
compatible = "fsl,mpc8560-scc-uart",
"fsl,cpm2-scc-uart";
- reg = <91a20 20 88100 100>;
+ reg = <0x91a20 0x20 0x88100 0x100>;
fsl,cpm-brg = <2>;
- fsl,cpm-command = <04a00000>;
- current-speed = <1c200>;
- interrupts = <29 8>;
+ fsl,cpm-command = <0x4a00000>;
+ current-speed = <115200>;
+ interrupts = <41 8>;
interrupt-parent = <&cpmpic>;
};
device_type = "network";
compatible = "fsl,mpc8560-fcc-enet",
"fsl,cpm2-fcc-enet";
- reg = <91320 20 88500 100 913b0 1>;
+ reg = <0x91320 0x20 0x88500 0x100 0x913b0 0x1>;
local-mac-address = [ 00 00 00 00 00 00 ];
- fsl,cpm-command = <16200300>;
- interrupts = <21 8>;
+ fsl,cpm-command = <0x16200300>;
+ interrupts = <33 8>;
interrupt-parent = <&cpmpic>;
phy-handle = <&phy2>;
};
device_type = "network";
compatible = "fsl,mpc8560-fcc-enet",
"fsl,cpm2-fcc-enet";
- reg = <91340 20 88600 100 913d0 1>;
+ reg = <0x91340 0x20 0x88600 0x100 0x913d0 0x1>;
local-mac-address = [ 00 00 00 00 00 00 ];
- fsl,cpm-command = <1a400300>;
- interrupts = <22 8>;
+ fsl,cpm-command = <0x1a400300>;
+ interrupts = <34 8>;
interrupt-parent = <&cpmpic>;
phy-handle = <&phy3>;
};
#address-cells = <3>;
compatible = "fsl,mpc8540-pcix", "fsl,mpc8540-pci";
device_type = "pci";
- reg = <e0008000 1000>;
- clock-frequency = <3f940aa>;
- interrupt-map-mask = <f800 0 0 7>;
+ reg = <0xe0008000 0x1000>;
+ clock-frequency = <66666666>;
+ interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
interrupt-map = <
/* IDSEL 0x2 */
- 1000 0 0 1 &mpic 1 1
- 1000 0 0 2 &mpic 2 1
- 1000 0 0 3 &mpic 3 1
- 1000 0 0 4 &mpic 4 1
+ 0x1000 0x0 0x0 0x1 &mpic 0x1 0x1
+ 0x1000 0x0 0x0 0x2 &mpic 0x2 0x1
+ 0x1000 0x0 0x0 0x3 &mpic 0x3 0x1
+ 0x1000 0x0 0x0 0x4 &mpic 0x4 0x1
/* IDSEL 0x3 */
- 1800 0 0 1 &mpic 4 1
- 1800 0 0 2 &mpic 1 1
- 1800 0 0 3 &mpic 2 1
- 1800 0 0 4 &mpic 3 1
+ 0x1800 0x0 0x0 0x1 &mpic 0x4 0x1
+ 0x1800 0x0 0x0 0x2 &mpic 0x1 0x1
+ 0x1800 0x0 0x0 0x3 &mpic 0x2 0x1
+ 0x1800 0x0 0x0 0x4 &mpic 0x3 0x1
/* IDSEL 0x4 */
- 2000 0 0 1 &mpic 3 1
- 2000 0 0 2 &mpic 4 1
- 2000 0 0 3 &mpic 1 1
- 2000 0 0 4 &mpic 2 1
+ 0x2000 0x0 0x0 0x1 &mpic 0x3 0x1
+ 0x2000 0x0 0x0 0x2 &mpic 0x4 0x1
+ 0x2000 0x0 0x0 0x3 &mpic 0x1 0x1
+ 0x2000 0x0 0x0 0x4 &mpic 0x2 0x1
/* IDSEL 0x5 */
- 2800 0 0 1 &mpic 2 1
- 2800 0 0 2 &mpic 3 1
- 2800 0 0 3 &mpic 4 1
- 2800 0 0 4 &mpic 1 1
+ 0x2800 0x0 0x0 0x1 &mpic 0x2 0x1
+ 0x2800 0x0 0x0 0x2 &mpic 0x3 0x1
+ 0x2800 0x0 0x0 0x3 &mpic 0x4 0x1
+ 0x2800 0x0 0x0 0x4 &mpic 0x1 0x1
/* IDSEL 12 */
- 6000 0 0 1 &mpic 1 1
- 6000 0 0 2 &mpic 2 1
- 6000 0 0 3 &mpic 3 1
- 6000 0 0 4 &mpic 4 1
+ 0x6000 0x0 0x0 0x1 &mpic 0x1 0x1
+ 0x6000 0x0 0x0 0x2 &mpic 0x2 0x1
+ 0x6000 0x0 0x0 0x3 &mpic 0x3 0x1
+ 0x6000 0x0 0x0 0x4 &mpic 0x4 0x1
/* IDSEL 13 */
- 6800 0 0 1 &mpic 4 1
- 6800 0 0 2 &mpic 1 1
- 6800 0 0 3 &mpic 2 1
- 6800 0 0 4 &mpic 3 1
+ 0x6800 0x0 0x0 0x1 &mpic 0x4 0x1
+ 0x6800 0x0 0x0 0x2 &mpic 0x1 0x1
+ 0x6800 0x0 0x0 0x3 &mpic 0x2 0x1
+ 0x6800 0x0 0x0 0x4 &mpic 0x3 0x1
/* IDSEL 14*/
- 7000 0 0 1 &mpic 3 1
- 7000 0 0 2 &mpic 4 1
- 7000 0 0 3 &mpic 1 1
- 7000 0 0 4 &mpic 2 1
+ 0x7000 0x0 0x0 0x1 &mpic 0x3 0x1
+ 0x7000 0x0 0x0 0x2 &mpic 0x4 0x1
+ 0x7000 0x0 0x0 0x3 &mpic 0x1 0x1
+ 0x7000 0x0 0x0 0x4 &mpic 0x2 0x1
/* IDSEL 15 */
- 7800 0 0 1 &mpic 2 1
- 7800 0 0 2 &mpic 3 1
- 7800 0 0 3 &mpic 4 1
- 7800 0 0 4 &mpic 1 1
+ 0x7800 0x0 0x0 0x1 &mpic 0x2 0x1
+ 0x7800 0x0 0x0 0x2 &mpic 0x3 0x1
+ 0x7800 0x0 0x0 0x3 &mpic 0x4 0x1
+ 0x7800 0x0 0x0 0x4 &mpic 0x1 0x1
/* IDSEL 18 */
- 9000 0 0 1 &mpic 1 1
- 9000 0 0 2 &mpic 2 1
- 9000 0 0 3 &mpic 3 1
- 9000 0 0 4 &mpic 4 1
+ 0x9000 0x0 0x0 0x1 &mpic 0x1 0x1
+ 0x9000 0x0 0x0 0x2 &mpic 0x2 0x1
+ 0x9000 0x0 0x0 0x3 &mpic 0x3 0x1
+ 0x9000 0x0 0x0 0x4 &mpic 0x4 0x1
/* IDSEL 19 */
- 9800 0 0 1 &mpic 4 1
- 9800 0 0 2 &mpic 1 1
- 9800 0 0 3 &mpic 2 1
- 9800 0 0 4 &mpic 3 1
+ 0x9800 0x0 0x0 0x1 &mpic 0x4 0x1
+ 0x9800 0x0 0x0 0x2 &mpic 0x1 0x1
+ 0x9800 0x0 0x0 0x3 &mpic 0x2 0x1
+ 0x9800 0x0 0x0 0x4 &mpic 0x3 0x1
/* IDSEL 20 */
- a000 0 0 1 &mpic 3 1
- a000 0 0 2 &mpic 4 1
- a000 0 0 3 &mpic 1 1
- a000 0 0 4 &mpic 2 1
+ 0xa000 0x0 0x0 0x1 &mpic 0x3 0x1
+ 0xa000 0x0 0x0 0x2 &mpic 0x4 0x1
+ 0xa000 0x0 0x0 0x3 &mpic 0x1 0x1
+ 0xa000 0x0 0x0 0x4 &mpic 0x2 0x1
/* IDSEL 21 */
- a800 0 0 1 &mpic 2 1
- a800 0 0 2 &mpic 3 1
- a800 0 0 3 &mpic 4 1
- a800 0 0 4 &mpic 1 1>;
+ 0xa800 0x0 0x0 0x1 &mpic 0x2 0x1
+ 0xa800 0x0 0x0 0x2 &mpic 0x3 0x1
+ 0xa800 0x0 0x0 0x3 &mpic 0x4 0x1
+ 0xa800 0x0 0x0 0x4 &mpic 0x1 0x1>;
interrupt-parent = <&mpic>;
- interrupts = <18 2>;
+ interrupts = <24 2>;
bus-range = <0 0>;
- ranges = <02000000 0 80000000 80000000 0 20000000
- 01000000 0 00000000 e2000000 0 01000000>;
+ ranges = <0x2000000 0x0 0x80000000 0x80000000 0x0 0x20000000
+ 0x1000000 0x0 0x0 0xe2000000 0x0 0x1000000>;
};
};
/*
* MPC8568E MDS Device Tree Source
*
- * Copyright 2007 Freescale Semiconductor Inc.
+ * Copyright 2007, 2008 Freescale Semiconductor Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* option) any later version.
*/
-
-/*
-/memreserve/ 00000000 1000000;
-*/
+/dts-v1/;
/ {
model = "MPC8568EMDS";
PowerPC,8568@0 {
device_type = "cpu";
- reg = <0>;
- d-cache-line-size = <20>; // 32 bytes
- i-cache-line-size = <20>; // 32 bytes
- d-cache-size = <8000>; // L1, 32K
- i-cache-size = <8000>; // L1, 32K
+ reg = <0x0>;
+ d-cache-line-size = <32>; // 32 bytes
+ i-cache-line-size = <32>; // 32 bytes
+ d-cache-size = <0x8000>; // L1, 32K
+ i-cache-size = <0x8000>; // L1, 32K
timebase-frequency = <0>;
bus-frequency = <0>;
clock-frequency = <0>;
memory {
device_type = "memory";
- reg = <00000000 10000000>;
+ reg = <0x0 0x10000000>;
};
bcsr@f8000000 {
device_type = "board-control";
- reg = <f8000000 8000>;
+ reg = <0xf8000000 0x8000>;
};
soc8568@e0000000 {
#address-cells = <1>;
#size-cells = <1>;
device_type = "soc";
- ranges = <0 e0000000 00100000>;
- reg = <e0000000 00001000>;
+ ranges = <0x0 0xe0000000 0x100000>;
+ reg = <0xe0000000 0x1000>;
bus-frequency = <0>;
memory-controller@2000 {
compatible = "fsl,8568-memory-controller";
- reg = <2000 1000>;
+ reg = <0x2000 0x1000>;
interrupt-parent = <&mpic>;
- interrupts = <12 2>;
+ interrupts = <18 2>;
};
l2-cache-controller@20000 {
compatible = "fsl,8568-l2-cache-controller";
- reg = <20000 1000>;
- cache-line-size = <20>; // 32 bytes
- cache-size = <80000>; // L2, 512K
+ reg = <0x20000 0x1000>;
+ cache-line-size = <32>; // 32 bytes
+ cache-size = <0x80000>; // L2, 512K
interrupt-parent = <&mpic>;
- interrupts = <10 2>;
+ interrupts = <16 2>;
};
i2c@3000 {
#size-cells = <0>;
cell-index = <0>;
compatible = "fsl-i2c";
- reg = <3000 100>;
- interrupts = <2b 2>;
+ reg = <0x3000 0x100>;
+ interrupts = <43 2>;
interrupt-parent = <&mpic>;
dfsrr;
rtc@68 {
compatible = "dallas,ds1374";
- reg = <68>;
+ reg = <0x68>;
};
};
#size-cells = <0>;
cell-index = <1>;
compatible = "fsl-i2c";
- reg = <3100 100>;
- interrupts = <2b 2>;
+ reg = <0x3100 0x100>;
+ interrupts = <43 2>;
interrupt-parent = <&mpic>;
dfsrr;
};
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,gianfar-mdio";
- reg = <24520 20>;
+ reg = <0x24520 0x20>;
phy0: ethernet-phy@7 {
interrupt-parent = <&mpic>;
interrupts = <1 1>;
- reg = <7>;
+ reg = <0x7>;
device_type = "ethernet-phy";
};
phy1: ethernet-phy@1 {
interrupt-parent = <&mpic>;
interrupts = <2 1>;
- reg = <1>;
+ reg = <0x1>;
device_type = "ethernet-phy";
};
phy2: ethernet-phy@2 {
interrupt-parent = <&mpic>;
interrupts = <1 1>;
- reg = <2>;
+ reg = <0x2>;
device_type = "ethernet-phy";
};
phy3: ethernet-phy@3 {
interrupt-parent = <&mpic>;
interrupts = <2 1>;
- reg = <3>;
+ reg = <0x3>;
device_type = "ethernet-phy";
};
};
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
- reg = <24000 1000>;
+ reg = <0x24000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <1d 2 1e 2 22 2>;
+ interrupts = <29 2 30 2 34 2>;
interrupt-parent = <&mpic>;
phy-handle = <&phy2>;
};
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
- reg = <25000 1000>;
+ reg = <0x25000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <23 2 24 2 28 2>;
+ interrupts = <35 2 36 2 40 2>;
interrupt-parent = <&mpic>;
phy-handle = <&phy3>;
};
cell-index = <0>;
device_type = "serial";
compatible = "ns16550";
- reg = <4500 100>;
+ reg = <0x4500 0x100>;
clock-frequency = <0>;
- interrupts = <2a 2>;
+ interrupts = <42 2>;
interrupt-parent = <&mpic>;
};
global-utilities@e0000 { //global utilities block
compatible = "fsl,mpc8548-guts";
- reg = <e0000 1000>;
+ reg = <0xe0000 0x1000>;
fsl,has-rstcr;
};
cell-index = <1>;
device_type = "serial";
compatible = "ns16550";
- reg = <4600 100>;
+ reg = <0x4600 0x100>;
clock-frequency = <0>;
- interrupts = <2a 2>;
+ interrupts = <42 2>;
interrupt-parent = <&mpic>;
};
device_type = "crypto";
model = "SEC2";
compatible = "talitos";
- reg = <30000 f000>;
- interrupts = <2d 2>;
+ reg = <0x30000 0xf000>;
+ interrupts = <45 2>;
interrupt-parent = <&mpic>;
num-channels = <4>;
- channel-fifo-len = <18>;
- exec-units-mask = <000000fe>;
- descriptor-types-mask = <012b0ebf>;
+ channel-fifo-len = <24>;
+ exec-units-mask = <0xfe>;
+ descriptor-types-mask = <0x12b0ebf>;
};
mpic: pic@40000 {
interrupt-controller;
#address-cells = <0>;
#interrupt-cells = <2>;
- reg = <40000 40000>;
+ reg = <0x40000 0x40000>;
compatible = "chrp,open-pic";
device_type = "open-pic";
big-endian;
};
par_io@e0100 {
- reg = <e0100 100>;
+ reg = <0xe0100 0x100>;
device_type = "par_io";
num-ports = <7>;
pio1: ucc_pin@01 {
pio-map = <
/* port pin dir open_drain assignment has_irq */
- 4 0a 1 0 2 0 /* TxD0 */
- 4 09 1 0 2 0 /* TxD1 */
- 4 08 1 0 2 0 /* TxD2 */
- 4 07 1 0 2 0 /* TxD3 */
- 4 17 1 0 2 0 /* TxD4 */
- 4 16 1 0 2 0 /* TxD5 */
- 4 15 1 0 2 0 /* TxD6 */
- 4 14 1 0 2 0 /* TxD7 */
- 4 0f 2 0 2 0 /* RxD0 */
- 4 0e 2 0 2 0 /* RxD1 */
- 4 0d 2 0 2 0 /* RxD2 */
- 4 0c 2 0 2 0 /* RxD3 */
- 4 1d 2 0 2 0 /* RxD4 */
- 4 1c 2 0 2 0 /* RxD5 */
- 4 1b 2 0 2 0 /* RxD6 */
- 4 1a 2 0 2 0 /* RxD7 */
- 4 0b 1 0 2 0 /* TX_EN */
- 4 18 1 0 2 0 /* TX_ER */
- 4 10 2 0 2 0 /* RX_DV */
- 4 1e 2 0 2 0 /* RX_ER */
- 4 11 2 0 2 0 /* RX_CLK */
- 4 13 1 0 2 0 /* GTX_CLK */
- 1 1f 2 0 3 0>; /* GTX125 */
+ 0x4 0xa 0x1 0x0 0x2 0x0 /* TxD0 */
+ 0x4 0x9 0x1 0x0 0x2 0x0 /* TxD1 */
+ 0x4 0x8 0x1 0x0 0x2 0x0 /* TxD2 */
+ 0x4 0x7 0x1 0x0 0x2 0x0 /* TxD3 */
+ 0x4 0x17 0x1 0x0 0x2 0x0 /* TxD4 */
+ 0x4 0x16 0x1 0x0 0x2 0x0 /* TxD5 */
+ 0x4 0x15 0x1 0x0 0x2 0x0 /* TxD6 */
+ 0x4 0x14 0x1 0x0 0x2 0x0 /* TxD7 */
+ 0x4 0xf 0x2 0x0 0x2 0x0 /* RxD0 */
+ 0x4 0xe 0x2 0x0 0x2 0x0 /* RxD1 */
+ 0x4 0xd 0x2 0x0 0x2 0x0 /* RxD2 */
+ 0x4 0xc 0x2 0x0 0x2 0x0 /* RxD3 */
+ 0x4 0x1d 0x2 0x0 0x2 0x0 /* RxD4 */
+ 0x4 0x1c 0x2 0x0 0x2 0x0 /* RxD5 */
+ 0x4 0x1b 0x2 0x0 0x2 0x0 /* RxD6 */
+ 0x4 0x1a 0x2 0x0 0x2 0x0 /* RxD7 */
+ 0x4 0xb 0x1 0x0 0x2 0x0 /* TX_EN */
+ 0x4 0x18 0x1 0x0 0x2 0x0 /* TX_ER */
+ 0x4 0x10 0x2 0x0 0x2 0x0 /* RX_DV */
+ 0x4 0x1e 0x2 0x0 0x2 0x0 /* RX_ER */
+ 0x4 0x11 0x2 0x0 0x2 0x0 /* RX_CLK */
+ 0x4 0x13 0x1 0x0 0x2 0x0 /* GTX_CLK */
+ 0x1 0x1f 0x2 0x0 0x3 0x0>; /* GTX125 */
};
pio2: ucc_pin@02 {
pio-map = <
/* port pin dir open_drain assignment has_irq */
- 5 0a 1 0 2 0 /* TxD0 */
- 5 09 1 0 2 0 /* TxD1 */
- 5 08 1 0 2 0 /* TxD2 */
- 5 07 1 0 2 0 /* TxD3 */
- 5 17 1 0 2 0 /* TxD4 */
- 5 16 1 0 2 0 /* TxD5 */
- 5 15 1 0 2 0 /* TxD6 */
- 5 14 1 0 2 0 /* TxD7 */
- 5 0f 2 0 2 0 /* RxD0 */
- 5 0e 2 0 2 0 /* RxD1 */
- 5 0d 2 0 2 0 /* RxD2 */
- 5 0c 2 0 2 0 /* RxD3 */
- 5 1d 2 0 2 0 /* RxD4 */
- 5 1c 2 0 2 0 /* RxD5 */
- 5 1b 2 0 2 0 /* RxD6 */
- 5 1a 2 0 2 0 /* RxD7 */
- 5 0b 1 0 2 0 /* TX_EN */
- 5 18 1 0 2 0 /* TX_ER */
- 5 10 2 0 2 0 /* RX_DV */
- 5 1e 2 0 2 0 /* RX_ER */
- 5 11 2 0 2 0 /* RX_CLK */
- 5 13 1 0 2 0 /* GTX_CLK */
- 1 1f 2 0 3 0 /* GTX125 */
- 4 06 3 0 2 0 /* MDIO */
- 4 05 1 0 2 0>; /* MDC */
+ 0x5 0xa 0x1 0x0 0x2 0x0 /* TxD0 */
+ 0x5 0x9 0x1 0x0 0x2 0x0 /* TxD1 */
+ 0x5 0x8 0x1 0x0 0x2 0x0 /* TxD2 */
+ 0x5 0x7 0x1 0x0 0x2 0x0 /* TxD3 */
+ 0x5 0x17 0x1 0x0 0x2 0x0 /* TxD4 */
+ 0x5 0x16 0x1 0x0 0x2 0x0 /* TxD5 */
+ 0x5 0x15 0x1 0x0 0x2 0x0 /* TxD6 */
+ 0x5 0x14 0x1 0x0 0x2 0x0 /* TxD7 */
+ 0x5 0xf 0x2 0x0 0x2 0x0 /* RxD0 */
+ 0x5 0xe 0x2 0x0 0x2 0x0 /* RxD1 */
+ 0x5 0xd 0x2 0x0 0x2 0x0 /* RxD2 */
+ 0x5 0xc 0x2 0x0 0x2 0x0 /* RxD3 */
+ 0x5 0x1d 0x2 0x0 0x2 0x0 /* RxD4 */
+ 0x5 0x1c 0x2 0x0 0x2 0x0 /* RxD5 */
+ 0x5 0x1b 0x2 0x0 0x2 0x0 /* RxD6 */
+ 0x5 0x1a 0x2 0x0 0x2 0x0 /* RxD7 */
+ 0x5 0xb 0x1 0x0 0x2 0x0 /* TX_EN */
+ 0x5 0x18 0x1 0x0 0x2 0x0 /* TX_ER */
+ 0x5 0x10 0x2 0x0 0x2 0x0 /* RX_DV */
+ 0x5 0x1e 0x2 0x0 0x2 0x0 /* RX_ER */
+ 0x5 0x11 0x2 0x0 0x2 0x0 /* RX_CLK */
+ 0x5 0x13 0x1 0x0 0x2 0x0 /* GTX_CLK */
+ 0x1 0x1f 0x2 0x0 0x3 0x0 /* GTX125 */
+ 0x4 0x6 0x3 0x0 0x2 0x0 /* MDIO */
+ 0x4 0x5 0x1 0x0 0x2 0x0>; /* MDC */
};
};
};
#size-cells = <1>;
device_type = "qe";
compatible = "fsl,qe";
- ranges = <0 e0080000 00040000>;
- reg = <e0080000 480>;
+ ranges = <0x0 0xe0080000 0x40000>;
+ reg = <0xe0080000 0x480>;
brg-frequency = <0>;
- bus-frequency = <179A7B00>;
+ bus-frequency = <396000000>;
muram@10000 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "fsl,qe-muram", "fsl,cpm-muram";
- ranges = <0 00010000 0000c000>;
+ ranges = <0x0 0x10000 0x10000>;
data-only@0 {
compatible = "fsl,qe-muram-data",
"fsl,cpm-muram-data";
- reg = <0 c000>;
+ reg = <0x0 0x10000>;
};
};
spi@4c0 {
cell-index = <0>;
compatible = "fsl,spi";
- reg = <4c0 40>;
+ reg = <0x4c0 0x40>;
interrupts = <2>;
interrupt-parent = <&qeic>;
mode = "cpu";
spi@500 {
cell-index = <1>;
compatible = "fsl,spi";
- reg = <500 40>;
+ reg = <0x500 0x40>;
interrupts = <1>;
interrupt-parent = <&qeic>;
mode = "cpu";
enet2: ucc@2000 {
device_type = "network";
compatible = "ucc_geth";
- model = "UCC";
cell-index = <1>;
- device-id = <1>;
- reg = <2000 200>;
- interrupts = <20>;
+ reg = <0x2000 0x200>;
+ interrupts = <32>;
interrupt-parent = <&qeic>;
local-mac-address = [ 00 00 00 00 00 00 ];
rx-clock-name = "none";
enet3: ucc@3000 {
device_type = "network";
compatible = "ucc_geth";
- model = "UCC";
cell-index = <2>;
- device-id = <2>;
- reg = <3000 200>;
- interrupts = <21>;
+ reg = <0x3000 0x200>;
+ interrupts = <33>;
interrupt-parent = <&qeic>;
local-mac-address = [ 00 00 00 00 00 00 ];
rx-clock-name = "none";
mdio@2120 {
#address-cells = <1>;
#size-cells = <0>;
- reg = <2120 18>;
+ reg = <0x2120 0x18>;
compatible = "fsl,ucc-mdio";
/* These are the same PHYs as on
qe_phy0: ethernet-phy@07 {
interrupt-parent = <&mpic>;
interrupts = <1 1>;
- reg = <7>;
+ reg = <0x7>;
device_type = "ethernet-phy";
};
qe_phy1: ethernet-phy@01 {
interrupt-parent = <&mpic>;
interrupts = <2 1>;
- reg = <1>;
+ reg = <0x1>;
device_type = "ethernet-phy";
};
qe_phy2: ethernet-phy@02 {
interrupt-parent = <&mpic>;
interrupts = <1 1>;
- reg = <2>;
+ reg = <0x2>;
device_type = "ethernet-phy";
};
qe_phy3: ethernet-phy@03 {
interrupt-parent = <&mpic>;
interrupts = <2 1>;
- reg = <3>;
+ reg = <0x3>;
device_type = "ethernet-phy";
};
};
compatible = "fsl,qe-ic";
#address-cells = <0>;
#interrupt-cells = <1>;
- reg = <80 80>;
+ reg = <0x80 0x80>;
big-endian;
- interrupts = <2e 2 2e 2>; //high:30 low:30
+ interrupts = <46 2 46 2>; //high:30 low:30
interrupt-parent = <&mpic>;
};
pci0: pci@e0008000 {
cell-index = <0>;
- interrupt-map-mask = <f800 0 0 7>;
+ interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
interrupt-map = <
/* IDSEL 0x12 AD18 */
- 9000 0 0 1 &mpic 5 1
- 9000 0 0 2 &mpic 6 1
- 9000 0 0 3 &mpic 7 1
- 9000 0 0 4 &mpic 4 1
+ 0x9000 0x0 0x0 0x1 &mpic 0x5 0x1
+ 0x9000 0x0 0x0 0x2 &mpic 0x6 0x1
+ 0x9000 0x0 0x0 0x3 &mpic 0x7 0x1
+ 0x9000 0x0 0x0 0x4 &mpic 0x4 0x1
/* IDSEL 0x13 AD19 */
- 9800 0 0 1 &mpic 6 1
- 9800 0 0 2 &mpic 7 1
- 9800 0 0 3 &mpic 4 1
- 9800 0 0 4 &mpic 5 1>;
+ 0x9800 0x0 0x0 0x1 &mpic 0x6 0x1
+ 0x9800 0x0 0x0 0x2 &mpic 0x7 0x1
+ 0x9800 0x0 0x0 0x3 &mpic 0x4 0x1
+ 0x9800 0x0 0x0 0x4 &mpic 0x5 0x1>;
interrupt-parent = <&mpic>;
- interrupts = <18 2>;
- bus-range = <0 ff>;
- ranges = <02000000 0 80000000 80000000 0 20000000
- 01000000 0 00000000 e2000000 0 00800000>;
- clock-frequency = <3f940aa>;
+ interrupts = <24 2>;
+ bus-range = <0 255>;
+ ranges = <0x2000000 0x0 0x80000000 0x80000000 0x0 0x20000000
+ 0x1000000 0x0 0x0 0xe2000000 0x0 0x800000>;
+ clock-frequency = <66666666>;
#interrupt-cells = <1>;
#size-cells = <2>;
#address-cells = <3>;
- reg = <e0008000 1000>;
+ reg = <0xe0008000 0x1000>;
compatible = "fsl,mpc8540-pci";
device_type = "pci";
};
/* PCI Express */
pci1: pcie@e000a000 {
cell-index = <2>;
- interrupt-map-mask = <f800 0 0 7>;
+ interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
interrupt-map = <
/* IDSEL 0x0 (PEX) */
- 00000 0 0 1 &mpic 0 1
- 00000 0 0 2 &mpic 1 1
- 00000 0 0 3 &mpic 2 1
- 00000 0 0 4 &mpic 3 1>;
+ 00000 0x0 0x0 0x1 &mpic 0x0 0x1
+ 00000 0x0 0x0 0x2 &mpic 0x1 0x1
+ 00000 0x0 0x0 0x3 &mpic 0x2 0x1
+ 00000 0x0 0x0 0x4 &mpic 0x3 0x1>;
interrupt-parent = <&mpic>;
- interrupts = <1a 2>;
- bus-range = <0 ff>;
- ranges = <02000000 0 a0000000 a0000000 0 10000000
- 01000000 0 00000000 e2800000 0 00800000>;
- clock-frequency = <1fca055>;
+ interrupts = <26 2>;
+ bus-range = <0 255>;
+ ranges = <0x2000000 0x0 0xa0000000 0xa0000000 0x0 0x10000000
+ 0x1000000 0x0 0x0 0xe2800000 0x0 0x800000>;
+ clock-frequency = <33333333>;
#interrupt-cells = <1>;
#size-cells = <2>;
#address-cells = <3>;
- reg = <e000a000 1000>;
+ reg = <0xe000a000 0x1000>;
compatible = "fsl,mpc8548-pcie";
device_type = "pci";
pcie@0 {
- reg = <0 0 0 0 0>;
+ reg = <0x0 0x0 0x0 0x0 0x0>;
#size-cells = <2>;
#address-cells = <3>;
device_type = "pci";
- ranges = <02000000 0 a0000000
- 02000000 0 a0000000
- 0 10000000
+ ranges = <0x2000000 0x0 0xa0000000
+ 0x2000000 0x0 0xa0000000
+ 0x0 0x10000000
- 01000000 0 00000000
- 01000000 0 00000000
- 0 00800000>;
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x800000>;
};
};
};
/*
* MPC8572 DS Device Tree Source
*
- * Copyright 2007 Freescale Semiconductor Inc.
+ * Copyright 2007, 2008 Freescale Semiconductor Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* option) any later version.
*/
+/dts-v1/;
/ {
model = "fsl,MPC8572DS";
compatible = "fsl,MPC8572DS";
PowerPC,8572@0 {
device_type = "cpu";
- reg = <0>;
- d-cache-line-size = <20>; // 32 bytes
- i-cache-line-size = <20>; // 32 bytes
- d-cache-size = <8000>; // L1, 32K
- i-cache-size = <8000>; // L1, 32K
+ reg = <0x0>;
+ d-cache-line-size = <32>; // 32 bytes
+ i-cache-line-size = <32>; // 32 bytes
+ d-cache-size = <0x8000>; // L1, 32K
+ i-cache-size = <0x8000>; // L1, 32K
timebase-frequency = <0>;
bus-frequency = <0>;
clock-frequency = <0>;
PowerPC,8572@1 {
device_type = "cpu";
- reg = <1>;
- d-cache-line-size = <20>; // 32 bytes
- i-cache-line-size = <20>; // 32 bytes
- d-cache-size = <8000>; // L1, 32K
- i-cache-size = <8000>; // L1, 32K
+ reg = <0x1>;
+ d-cache-line-size = <32>; // 32 bytes
+ i-cache-line-size = <32>; // 32 bytes
+ d-cache-size = <0x8000>; // L1, 32K
+ i-cache-size = <0x8000>; // L1, 32K
timebase-frequency = <0>;
bus-frequency = <0>;
clock-frequency = <0>;
memory {
device_type = "memory";
- reg = <00000000 00000000>; // Filled by U-Boot
+ reg = <0x0 0x0>; // Filled by U-Boot
};
soc8572@ffe00000 {
#address-cells = <1>;
#size-cells = <1>;
device_type = "soc";
- ranges = <00000000 ffe00000 00100000>;
- reg = <ffe00000 00001000>; // CCSRBAR & soc regs, remove once parse code for immrbase fixed
+ ranges = <0x0 0xffe00000 0x100000>;
+ reg = <0xffe00000 0x1000>; // CCSRBAR & soc regs, remove once parse code for immrbase fixed
bus-frequency = <0>; // Filled out by uboot.
memory-controller@2000 {
compatible = "fsl,mpc8572-memory-controller";
- reg = <2000 1000>;
+ reg = <0x2000 0x1000>;
interrupt-parent = <&mpic>;
- interrupts = <12 2>;
+ interrupts = <18 2>;
};
memory-controller@6000 {
compatible = "fsl,mpc8572-memory-controller";
- reg = <6000 1000>;
+ reg = <0x6000 0x1000>;
interrupt-parent = <&mpic>;
- interrupts = <12 2>;
+ interrupts = <18 2>;
};
l2-cache-controller@20000 {
compatible = "fsl,mpc8572-l2-cache-controller";
- reg = <20000 1000>;
- cache-line-size = <20>; // 32 bytes
- cache-size = <80000>; // L2, 512K
+ reg = <0x20000 0x1000>;
+ cache-line-size = <32>; // 32 bytes
+ cache-size = <0x80000>; // L2, 512K
interrupt-parent = <&mpic>;
- interrupts = <10 2>;
+ interrupts = <16 2>;
};
i2c@3000 {
#size-cells = <0>;
cell-index = <0>;
compatible = "fsl-i2c";
- reg = <3000 100>;
- interrupts = <2b 2>;
+ reg = <0x3000 0x100>;
+ interrupts = <43 2>;
interrupt-parent = <&mpic>;
dfsrr;
};
#size-cells = <0>;
cell-index = <1>;
compatible = "fsl-i2c";
- reg = <3100 100>;
- interrupts = <2b 2>;
+ reg = <0x3100 0x100>;
+ interrupts = <43 2>;
interrupt-parent = <&mpic>;
dfsrr;
};
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,gianfar-mdio";
- reg = <24520 20>;
+ reg = <0x24520 0x20>;
phy0: ethernet-phy@0 {
interrupt-parent = <&mpic>;
- interrupts = <a 1>;
- reg = <0>;
+ interrupts = <10 1>;
+ reg = <0x0>;
};
phy1: ethernet-phy@1 {
interrupt-parent = <&mpic>;
- interrupts = <a 1>;
- reg = <1>;
+ interrupts = <10 1>;
+ reg = <0x1>;
};
phy2: ethernet-phy@2 {
interrupt-parent = <&mpic>;
- interrupts = <a 1>;
- reg = <2>;
+ interrupts = <10 1>;
+ reg = <0x2>;
};
phy3: ethernet-phy@3 {
interrupt-parent = <&mpic>;
- interrupts = <a 1>;
- reg = <3>;
+ interrupts = <10 1>;
+ reg = <0x3>;
};
};
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
- reg = <24000 1000>;
+ reg = <0x24000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <1d 2 1e 2 22 2>;
+ interrupts = <29 2 30 2 34 2>;
interrupt-parent = <&mpic>;
phy-handle = <&phy0>;
phy-connection-type = "rgmii-id";
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
- reg = <25000 1000>;
+ reg = <0x25000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <23 2 24 2 28 2>;
+ interrupts = <35 2 36 2 40 2>;
interrupt-parent = <&mpic>;
phy-handle = <&phy1>;
phy-connection-type = "rgmii-id";
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
- reg = <26000 1000>;
+ reg = <0x26000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <1f 2 20 2 21 2>;
+ interrupts = <31 2 32 2 33 2>;
interrupt-parent = <&mpic>;
phy-handle = <&phy2>;
phy-connection-type = "rgmii-id";
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
- reg = <27000 1000>;
+ reg = <0x27000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <25 2 26 2 27 2>;
+ interrupts = <37 2 38 2 39 2>;
interrupt-parent = <&mpic>;
phy-handle = <&phy3>;
phy-connection-type = "rgmii-id";
cell-index = <0>;
device_type = "serial";
compatible = "ns16550";
- reg = <4500 100>;
+ reg = <0x4500 0x100>;
clock-frequency = <0>;
- interrupts = <2a 2>;
+ interrupts = <42 2>;
interrupt-parent = <&mpic>;
};
cell-index = <1>;
device_type = "serial";
compatible = "ns16550";
- reg = <4600 100>;
+ reg = <0x4600 0x100>;
clock-frequency = <0>;
- interrupts = <2a 2>;
+ interrupts = <42 2>;
interrupt-parent = <&mpic>;
};
global-utilities@e0000 { //global utilities block
compatible = "fsl,mpc8572-guts";
- reg = <e0000 1000>;
+ reg = <0xe0000 0x1000>;
fsl,has-rstcr;
};
interrupt-controller;
#address-cells = <0>;
#interrupt-cells = <2>;
- reg = <40000 40000>;
+ reg = <0x40000 0x40000>;
compatible = "chrp,open-pic";
device_type = "open-pic";
big-endian;
#interrupt-cells = <1>;
#size-cells = <2>;
#address-cells = <3>;
- reg = <ffe08000 1000>;
- bus-range = <0 ff>;
- ranges = <02000000 0 80000000 80000000 0 20000000
- 01000000 0 00000000 ffc00000 0 00010000>;
- clock-frequency = <1fca055>;
+ reg = <0xffe08000 0x1000>;
+ bus-range = <0 255>;
+ ranges = <0x2000000 0x0 0x80000000 0x80000000 0x0 0x20000000
+ 0x1000000 0x0 0x0 0xffc00000 0x0 0x10000>;
+ clock-frequency = <33333333>;
interrupt-parent = <&mpic>;
- interrupts = <18 2>;
- interrupt-map-mask = <ff00 0 0 7>;
+ interrupts = <24 2>;
+ interrupt-map-mask = <0xff00 0x0 0x0 0x7>;
interrupt-map = <
/* IDSEL 0x11 func 0 - PCI slot 1 */
- 8800 0 0 1 &mpic 2 1
- 8800 0 0 2 &mpic 3 1
- 8800 0 0 3 &mpic 4 1
- 8800 0 0 4 &mpic 1 1
+ 0x8800 0x0 0x0 0x1 &mpic 0x2 0x1
+ 0x8800 0x0 0x0 0x2 &mpic 0x3 0x1
+ 0x8800 0x0 0x0 0x3 &mpic 0x4 0x1
+ 0x8800 0x0 0x0 0x4 &mpic 0x1 0x1
/* IDSEL 0x11 func 1 - PCI slot 1 */
- 8900 0 0 1 &mpic 2 1
- 8900 0 0 2 &mpic 3 1
- 8900 0 0 3 &mpic 4 1
- 8900 0 0 4 &mpic 1 1
+ 0x8900 0x0 0x0 0x1 &mpic 0x2 0x1
+ 0x8900 0x0 0x0 0x2 &mpic 0x3 0x1
+ 0x8900 0x0 0x0 0x3 &mpic 0x4 0x1
+ 0x8900 0x0 0x0 0x4 &mpic 0x1 0x1
/* IDSEL 0x11 func 2 - PCI slot 1 */
- 8a00 0 0 1 &mpic 2 1
- 8a00 0 0 2 &mpic 3 1
- 8a00 0 0 3 &mpic 4 1
- 8a00 0 0 4 &mpic 1 1
+ 0x8a00 0x0 0x0 0x1 &mpic 0x2 0x1
+ 0x8a00 0x0 0x0 0x2 &mpic 0x3 0x1
+ 0x8a00 0x0 0x0 0x3 &mpic 0x4 0x1
+ 0x8a00 0x0 0x0 0x4 &mpic 0x1 0x1
/* IDSEL 0x11 func 3 - PCI slot 1 */
- 8b00 0 0 1 &mpic 2 1
- 8b00 0 0 2 &mpic 3 1
- 8b00 0 0 3 &mpic 4 1
- 8b00 0 0 4 &mpic 1 1
+ 0x8b00 0x0 0x0 0x1 &mpic 0x2 0x1
+ 0x8b00 0x0 0x0 0x2 &mpic 0x3 0x1
+ 0x8b00 0x0 0x0 0x3 &mpic 0x4 0x1
+ 0x8b00 0x0 0x0 0x4 &mpic 0x1 0x1
/* IDSEL 0x11 func 4 - PCI slot 1 */
- 8c00 0 0 1 &mpic 2 1
- 8c00 0 0 2 &mpic 3 1
- 8c00 0 0 3 &mpic 4 1
- 8c00 0 0 4 &mpic 1 1
+ 0x8c00 0x0 0x0 0x1 &mpic 0x2 0x1
+ 0x8c00 0x0 0x0 0x2 &mpic 0x3 0x1
+ 0x8c00 0x0 0x0 0x3 &mpic 0x4 0x1
+ 0x8c00 0x0 0x0 0x4 &mpic 0x1 0x1
/* IDSEL 0x11 func 5 - PCI slot 1 */
- 8d00 0 0 1 &mpic 2 1
- 8d00 0 0 2 &mpic 3 1
- 8d00 0 0 3 &mpic 4 1
- 8d00 0 0 4 &mpic 1 1
+ 0x8d00 0x0 0x0 0x1 &mpic 0x2 0x1
+ 0x8d00 0x0 0x0 0x2 &mpic 0x3 0x1
+ 0x8d00 0x0 0x0 0x3 &mpic 0x4 0x1
+ 0x8d00 0x0 0x0 0x4 &mpic 0x1 0x1
/* IDSEL 0x11 func 6 - PCI slot 1 */
- 8e00 0 0 1 &mpic 2 1
- 8e00 0 0 2 &mpic 3 1
- 8e00 0 0 3 &mpic 4 1
- 8e00 0 0 4 &mpic 1 1
+ 0x8e00 0x0 0x0 0x1 &mpic 0x2 0x1
+ 0x8e00 0x0 0x0 0x2 &mpic 0x3 0x1
+ 0x8e00 0x0 0x0 0x3 &mpic 0x4 0x1
+ 0x8e00 0x0 0x0 0x4 &mpic 0x1 0x1
/* IDSEL 0x11 func 7 - PCI slot 1 */
- 8f00 0 0 1 &mpic 2 1
- 8f00 0 0 2 &mpic 3 1
- 8f00 0 0 3 &mpic 4 1
- 8f00 0 0 4 &mpic 1 1
+ 0x8f00 0x0 0x0 0x1 &mpic 0x2 0x1
+ 0x8f00 0x0 0x0 0x2 &mpic 0x3 0x1
+ 0x8f00 0x0 0x0 0x3 &mpic 0x4 0x1
+ 0x8f00 0x0 0x0 0x4 &mpic 0x1 0x1
/* IDSEL 0x12 func 0 - PCI slot 2 */
- 9000 0 0 1 &mpic 3 1
- 9000 0 0 2 &mpic 4 1
- 9000 0 0 3 &mpic 1 1
- 9000 0 0 4 &mpic 2 1
+ 0x9000 0x0 0x0 0x1 &mpic 0x3 0x1
+ 0x9000 0x0 0x0 0x2 &mpic 0x4 0x1
+ 0x9000 0x0 0x0 0x3 &mpic 0x1 0x1
+ 0x9000 0x0 0x0 0x4 &mpic 0x2 0x1
/* IDSEL 0x12 func 1 - PCI slot 2 */
- 9100 0 0 1 &mpic 3 1
- 9100 0 0 2 &mpic 4 1
- 9100 0 0 3 &mpic 1 1
- 9100 0 0 4 &mpic 2 1
+ 0x9100 0x0 0x0 0x1 &mpic 0x3 0x1
+ 0x9100 0x0 0x0 0x2 &mpic 0x4 0x1
+ 0x9100 0x0 0x0 0x3 &mpic 0x1 0x1
+ 0x9100 0x0 0x0 0x4 &mpic 0x2 0x1
/* IDSEL 0x12 func 2 - PCI slot 2 */
- 9200 0 0 1 &mpic 3 1
- 9200 0 0 2 &mpic 4 1
- 9200 0 0 3 &mpic 1 1
- 9200 0 0 4 &mpic 2 1
+ 0x9200 0x0 0x0 0x1 &mpic 0x3 0x1
+ 0x9200 0x0 0x0 0x2 &mpic 0x4 0x1
+ 0x9200 0x0 0x0 0x3 &mpic 0x1 0x1
+ 0x9200 0x0 0x0 0x4 &mpic 0x2 0x1
/* IDSEL 0x12 func 3 - PCI slot 2 */
- 9300 0 0 1 &mpic 3 1
- 9300 0 0 2 &mpic 4 1
- 9300 0 0 3 &mpic 1 1
- 9300 0 0 4 &mpic 2 1
+ 0x9300 0x0 0x0 0x1 &mpic 0x3 0x1
+ 0x9300 0x0 0x0 0x2 &mpic 0x4 0x1
+ 0x9300 0x0 0x0 0x3 &mpic 0x1 0x1
+ 0x9300 0x0 0x0 0x4 &mpic 0x2 0x1
/* IDSEL 0x12 func 4 - PCI slot 2 */
- 9400 0 0 1 &mpic 3 1
- 9400 0 0 2 &mpic 4 1
- 9400 0 0 3 &mpic 1 1
- 9400 0 0 4 &mpic 2 1
+ 0x9400 0x0 0x0 0x1 &mpic 0x3 0x1
+ 0x9400 0x0 0x0 0x2 &mpic 0x4 0x1
+ 0x9400 0x0 0x0 0x3 &mpic 0x1 0x1
+ 0x9400 0x0 0x0 0x4 &mpic 0x2 0x1
/* IDSEL 0x12 func 5 - PCI slot 2 */
- 9500 0 0 1 &mpic 3 1
- 9500 0 0 2 &mpic 4 1
- 9500 0 0 3 &mpic 1 1
- 9500 0 0 4 &mpic 2 1
+ 0x9500 0x0 0x0 0x1 &mpic 0x3 0x1
+ 0x9500 0x0 0x0 0x2 &mpic 0x4 0x1
+ 0x9500 0x0 0x0 0x3 &mpic 0x1 0x1
+ 0x9500 0x0 0x0 0x4 &mpic 0x2 0x1
/* IDSEL 0x12 func 6 - PCI slot 2 */
- 9600 0 0 1 &mpic 3 1
- 9600 0 0 2 &mpic 4 1
- 9600 0 0 3 &mpic 1 1
- 9600 0 0 4 &mpic 2 1
+ 0x9600 0x0 0x0 0x1 &mpic 0x3 0x1
+ 0x9600 0x0 0x0 0x2 &mpic 0x4 0x1
+ 0x9600 0x0 0x0 0x3 &mpic 0x1 0x1
+ 0x9600 0x0 0x0 0x4 &mpic 0x2 0x1
/* IDSEL 0x12 func 7 - PCI slot 2 */
- 9700 0 0 1 &mpic 3 1
- 9700 0 0 2 &mpic 4 1
- 9700 0 0 3 &mpic 1 1
- 9700 0 0 4 &mpic 2 1
+ 0x9700 0x0 0x0 0x1 &mpic 0x3 0x1
+ 0x9700 0x0 0x0 0x2 &mpic 0x4 0x1
+ 0x9700 0x0 0x0 0x3 &mpic 0x1 0x1
+ 0x9700 0x0 0x0 0x4 &mpic 0x2 0x1
// IDSEL 0x1c USB
- e000 0 0 1 &i8259 c 2
- e100 0 0 2 &i8259 9 2
- e200 0 0 3 &i8259 a 2
- e300 0 0 4 &i8259 b 2
+ 0xe000 0x0 0x0 0x1 &i8259 0xc 0x2
+ 0xe100 0x0 0x0 0x2 &i8259 0x9 0x2
+ 0xe200 0x0 0x0 0x3 &i8259 0xa 0x2
+ 0xe300 0x0 0x0 0x4 &i8259 0xb 0x2
// IDSEL 0x1d Audio
- e800 0 0 1 &i8259 6 2
+ 0xe800 0x0 0x0 0x1 &i8259 0x6 0x2
// IDSEL 0x1e Legacy
- f000 0 0 1 &i8259 7 2
- f100 0 0 1 &i8259 7 2
+ 0xf000 0x0 0x0 0x1 &i8259 0x7 0x2
+ 0xf100 0x0 0x0 0x1 &i8259 0x7 0x2
// IDSEL 0x1f IDE/SATA
- f800 0 0 1 &i8259 e 2
- f900 0 0 1 &i8259 5 2
+ 0xf800 0x0 0x0 0x1 &i8259 0xe 0x2
+ 0xf900 0x0 0x0 0x1 &i8259 0x5 0x2
>;
pcie@0 {
- reg = <0 0 0 0 0>;
+ reg = <0x0 0x0 0x0 0x0 0x0>;
#size-cells = <2>;
#address-cells = <3>;
device_type = "pci";
- ranges = <02000000 0 80000000
- 02000000 0 80000000
- 0 20000000
+ ranges = <0x2000000 0x0 0x80000000
+ 0x2000000 0x0 0x80000000
+ 0x0 0x20000000
- 01000000 0 00000000
- 01000000 0 00000000
- 0 00100000>;
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x100000>;
uli1575@0 {
- reg = <0 0 0 0 0>;
+ reg = <0x0 0x0 0x0 0x0 0x0>;
#size-cells = <2>;
#address-cells = <3>;
- ranges = <02000000 0 80000000
- 02000000 0 80000000
- 0 20000000
+ ranges = <0x2000000 0x0 0x80000000
+ 0x2000000 0x0 0x80000000
+ 0x0 0x20000000
- 01000000 0 00000000
- 01000000 0 00000000
- 0 00100000>;
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x100000>;
isa@1e {
device_type = "isa";
#interrupt-cells = <2>;
#size-cells = <1>;
#address-cells = <2>;
- reg = <f000 0 0 0 0>;
- ranges = <1 0 01000000 0 0
- 00001000>;
+ reg = <0xf000 0x0 0x0 0x0 0x0>;
+ ranges = <0x1 0x0 0x1000000 0x0 0x0
+ 0x1000>;
interrupt-parent = <&i8259>;
i8259: interrupt-controller@20 {
- reg = <1 20 2
- 1 a0 2
- 1 4d0 2>;
+ reg = <0x1 0x20 0x2
+ 0x1 0xa0 0x2
+ 0x1 0x4d0 0x2>;
interrupt-controller;
device_type = "interrupt-controller";
#address-cells = <0>;
i8042@60 {
#size-cells = <0>;
#address-cells = <1>;
- reg = <1 60 1 1 64 1>;
- interrupts = <1 3 c 3>;
+ reg = <0x1 0x60 0x1 0x1 0x64 0x1>;
+ interrupts = <1 3 12 3>;
interrupt-parent =
<&i8259>;
keyboard@0 {
- reg = <0>;
+ reg = <0x0>;
compatible = "pnpPNP,303";
};
mouse@1 {
- reg = <1>;
+ reg = <0x1>;
compatible = "pnpPNP,f03";
};
};
rtc@70 {
compatible = "pnpPNP,b00";
- reg = <1 70 2>;
+ reg = <0x1 0x70 0x2>;
};
gpio@400 {
- reg = <1 400 80>;
+ reg = <0x1 0x400 0x80>;
};
};
};
#interrupt-cells = <1>;
#size-cells = <2>;
#address-cells = <3>;
- reg = <ffe09000 1000>;
- bus-range = <0 ff>;
- ranges = <02000000 0 a0000000 a0000000 0 20000000
- 01000000 0 00000000 ffc10000 0 00010000>;
- clock-frequency = <1fca055>;
+ reg = <0xffe09000 0x1000>;
+ bus-range = <0 255>;
+ ranges = <0x2000000 0x0 0xa0000000 0xa0000000 0x0 0x20000000
+ 0x1000000 0x0 0x0 0xffc10000 0x0 0x10000>;
+ clock-frequency = <33333333>;
interrupt-parent = <&mpic>;
- interrupts = <1a 2>;
- interrupt-map-mask = <f800 0 0 7>;
+ interrupts = <26 2>;
+ interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
interrupt-map = <
/* IDSEL 0x0 */
- 0000 0 0 1 &mpic 4 1
- 0000 0 0 2 &mpic 5 1
- 0000 0 0 3 &mpic 6 1
- 0000 0 0 4 &mpic 7 1
+ 0000 0x0 0x0 0x1 &mpic 0x4 0x1
+ 0000 0x0 0x0 0x2 &mpic 0x5 0x1
+ 0000 0x0 0x0 0x3 &mpic 0x6 0x1
+ 0000 0x0 0x0 0x4 &mpic 0x7 0x1
>;
pcie@0 {
- reg = <0 0 0 0 0>;
+ reg = <0x0 0x0 0x0 0x0 0x0>;
#size-cells = <2>;
#address-cells = <3>;
device_type = "pci";
- ranges = <02000000 0 a0000000
- 02000000 0 a0000000
- 0 20000000
+ ranges = <0x2000000 0x0 0xa0000000
+ 0x2000000 0x0 0xa0000000
+ 0x0 0x20000000
- 01000000 0 00000000
- 01000000 0 00000000
- 0 00100000>;
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x100000>;
};
};
#interrupt-cells = <1>;
#size-cells = <2>;
#address-cells = <3>;
- reg = <ffe0a000 1000>;
- bus-range = <0 ff>;
- ranges = <02000000 0 c0000000 c0000000 0 20000000
- 01000000 0 00000000 ffc20000 0 00010000>;
- clock-frequency = <1fca055>;
+ reg = <0xffe0a000 0x1000>;
+ bus-range = <0 255>;
+ ranges = <0x2000000 0x0 0xc0000000 0xc0000000 0x0 0x20000000
+ 0x1000000 0x0 0x0 0xffc20000 0x0 0x10000>;
+ clock-frequency = <33333333>;
interrupt-parent = <&mpic>;
- interrupts = <1b 2>;
- interrupt-map-mask = <f800 0 0 7>;
+ interrupts = <27 2>;
+ interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
interrupt-map = <
/* IDSEL 0x0 */
- 0000 0 0 1 &mpic 0 1
- 0000 0 0 2 &mpic 1 1
- 0000 0 0 3 &mpic 2 1
- 0000 0 0 4 &mpic 3 1
+ 0000 0x0 0x0 0x1 &mpic 0x0 0x1
+ 0000 0x0 0x0 0x2 &mpic 0x1 0x1
+ 0000 0x0 0x0 0x3 &mpic 0x2 0x1
+ 0000 0x0 0x0 0x4 &mpic 0x3 0x1
>;
pcie@0 {
- reg = <0 0 0 0 0>;
+ reg = <0x0 0x0 0x0 0x0 0x0>;
#size-cells = <2>;
#address-cells = <3>;
device_type = "pci";
- ranges = <02000000 0 c0000000
- 02000000 0 c0000000
- 0 20000000
+ ranges = <0x2000000 0x0 0xc0000000
+ 0x2000000 0x0 0xc0000000
+ 0x0 0x20000000
- 01000000 0 00000000
- 01000000 0 00000000
- 0 00100000>;
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x100000>;
};
};
};
/ {
model = "MPC8641HPCN";
- compatible = "mpc86xx";
+ compatible = "fsl,mpc8641hpcn";
#address-cells = <1>;
#size-cells = <1>;
* MPC866 ADS Device Tree Source
*
* Copyright 2006 MontaVista Software, Inc.
+ * Copyright 2008 Freescale Semiconductor, Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* option) any later version.
*/
+/dts-v1/;
/ {
model = "MPC866ADS";
PowerPC,866@0 {
device_type = "cpu";
- reg = <0>;
- d-cache-line-size = <10>; // 16 bytes
- i-cache-line-size = <10>; // 16 bytes
- d-cache-size = <2000>; // L1, 8K
- i-cache-size = <4000>; // L1, 16K
+ reg = <0x0>;
+ d-cache-line-size = <16>; // 16 bytes
+ i-cache-line-size = <16>; // 16 bytes
+ d-cache-size = <0x2000>; // L1, 8K
+ i-cache-size = <0x4000>; // L1, 16K
timebase-frequency = <0>;
bus-frequency = <0>;
clock-frequency = <0>;
- interrupts = <f 2>; // decrementer interrupt
+ interrupts = <15 2>; // decrementer interrupt
interrupt-parent = <&PIC>;
};
};
memory {
device_type = "memory";
- reg = <00000000 800000>;
+ reg = <0x0 0x800000>;
};
localbus@ff000100 {
compatible = "fsl,mpc866-localbus", "fsl,pq1-localbus";
#address-cells = <2>;
#size-cells = <1>;
- reg = <ff000100 40>;
+ reg = <0xff000100 0x40>;
ranges = <
- 1 0 ff080000 00008000
- 5 0 ff0a0000 00008000
+ 0x1 0x0 0xff080000 0x8000
+ 0x5 0x0 0xff0a0000 0x8000
>;
board-control@1,0 {
- reg = <1 0 20 5 300 4>;
+ reg = <0x1 0x0 0x20 0x5 0x300 0x4>;
compatible = "fsl,mpc866ads-bcsr";
};
};
#address-cells = <1>;
#size-cells = <1>;
device_type = "soc";
- ranges = <0 ff000000 00100000>;
- reg = <ff000000 00000200>;
+ ranges = <0x0 0xff000000 0x100000>;
+ reg = <0xff000000 0x200>;
bus-frequency = <0>;
mdio@e00 {
compatible = "fsl,mpc866-fec-mdio", "fsl,pq1-fec-mdio";
- reg = <e00 188>;
+ reg = <0xe00 0x188>;
#address-cells = <1>;
#size-cells = <0>;
PHY: ethernet-phy@f {
- reg = <f>;
+ reg = <0xf>;
device_type = "ethernet-phy";
};
};
device_type = "network";
compatible = "fsl,mpc866-fec-enet",
"fsl,pq1-fec-enet";
- reg = <e00 188>;
+ reg = <0xe00 0x188>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <3 1>;
interrupt-parent = <&PIC>;
PIC: pic@0 {
interrupt-controller;
#interrupt-cells = <2>;
- reg = <0 24>;
+ reg = <0x0 0x24>;
compatible = "fsl,mpc866-pic", "fsl,pq1-pic";
};
#size-cells = <1>;
compatible = "fsl,mpc866-cpm", "fsl,cpm1";
ranges;
- reg = <9c0 40>;
+ reg = <0x9c0 0x40>;
brg-frequency = <0>;
interrupts = <0 2>; // cpm error interrupt
interrupt-parent = <&CPM_PIC>;
muram@2000 {
#address-cells = <1>;
#size-cells = <1>;
- ranges = <0 2000 2000>;
+ ranges = <0x0 0x2000 0x2000>;
data@0 {
compatible = "fsl,cpm-muram-data";
- reg = <0 1c00>;
+ reg = <0x0 0x1c00>;
};
};
compatible = "fsl,mpc866-brg",
"fsl,cpm1-brg",
"fsl,cpm-brg";
- reg = <9f0 10>;
+ reg = <0x9f0 0x10>;
clock-frequency = <0>;
};
#interrupt-cells = <1>;
interrupts = <5 2 0 2>;
interrupt-parent = <&PIC>;
- reg = <930 20>;
+ reg = <0x930 0x20>;
compatible = "fsl,mpc866-cpm-pic",
"fsl,cpm1-pic";
};
device_type = "serial";
compatible = "fsl,mpc866-smc-uart",
"fsl,cpm1-smc-uart";
- reg = <a80 10 3e80 40>;
+ reg = <0xa80 0x10 0x3e80 0x40>;
interrupts = <4>;
interrupt-parent = <&CPM_PIC>;
fsl,cpm-brg = <1>;
- fsl,cpm-command = <0090>;
+ fsl,cpm-command = <0x90>;
};
serial@a90 {
device_type = "serial";
compatible = "fsl,mpc866-smc-uart",
"fsl,cpm1-smc-uart";
- reg = <a90 10 3f80 40>;
+ reg = <0xa90 0x10 0x3f80 0x40>;
interrupts = <3>;
interrupt-parent = <&CPM_PIC>;
fsl,cpm-brg = <2>;
- fsl,cpm-command = <00d0>;
+ fsl,cpm-command = <0xd0>;
};
ethernet@a00 {
device_type = "network";
compatible = "fsl,mpc866-scc-enet",
"fsl,cpm1-scc-enet";
- reg = <a00 18 3c00 100>;
+ reg = <0xa00 0x18 0x3c00 0x100>;
local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <1e>;
+ interrupts = <30>;
interrupt-parent = <&CPM_PIC>;
fsl,cpm-command = <0000>;
linux,network-index = <1>;
* MPC885 ADS Device Tree Source
*
* Copyright 2006 MontaVista Software, Inc.
- * Copyright 2007 Freescale Semiconductor, Inc.
+ * Copyright 2007,2008 Freescale Semiconductor, Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* option) any later version.
*/
+/dts-v1/;
/ {
model = "MPC885ADS";
PowerPC,885@0 {
device_type = "cpu";
- reg = <0>;
- d-cache-line-size = <d#16>;
- i-cache-line-size = <d#16>;
- d-cache-size = <d#8192>;
- i-cache-size = <d#8192>;
+ reg = <0x0>;
+ d-cache-line-size = <16>;
+ i-cache-line-size = <16>;
+ d-cache-size = <8192>;
+ i-cache-size = <8192>;
timebase-frequency = <0>;
bus-frequency = <0>;
clock-frequency = <0>;
- interrupts = <f 2>; // decrementer interrupt
+ interrupts = <15 2>; // decrementer interrupt
interrupt-parent = <&PIC>;
};
};
memory {
device_type = "memory";
- reg = <0 0>;
+ reg = <0x0 0x0>;
};
localbus@ff000100 {
compatible = "fsl,mpc885-localbus", "fsl,pq1-localbus";
#address-cells = <2>;
#size-cells = <1>;
- reg = <ff000100 40>;
+ reg = <0xff000100 0x40>;
ranges = <
- 0 0 fe000000 00800000
- 1 0 ff080000 00008000
- 5 0 ff0a0000 00008000
+ 0x0 0x0 0xfe000000 0x800000
+ 0x1 0x0 0xff080000 0x8000
+ 0x5 0x0 0xff0a0000 0x8000
>;
flash@0,0 {
compatible = "jedec-flash";
- reg = <0 0 800000>;
+ reg = <0x0 0x0 0x800000>;
bank-width = <4>;
device-width = <1>;
};
board-control@1,0 {
- reg = <1 0 20 5 300 4>;
+ reg = <0x1 0x0 0x20 0x5 0x300 0x4>;
compatible = "fsl,mpc885ads-bcsr";
};
};
#address-cells = <1>;
#size-cells = <1>;
device_type = "soc";
- ranges = <0 ff000000 00004000>;
+ ranges = <0x0 0xff000000 0x4000>;
bus-frequency = <0>;
// Temporary -- will go away once kernel uses ranges for get_immrbase().
- reg = <ff000000 4000>;
+ reg = <0xff000000 0x4000>;
mdio@e00 {
compatible = "fsl,mpc885-fec-mdio", "fsl,pq1-fec-mdio";
- reg = <e00 188>;
+ reg = <0xe00 0x188>;
#address-cells = <1>;
#size-cells = <0>;
PHY0: ethernet-phy@0 {
- reg = <0>;
+ reg = <0x0>;
device_type = "ethernet-phy";
};
PHY1: ethernet-phy@1 {
- reg = <1>;
+ reg = <0x1>;
device_type = "ethernet-phy";
};
PHY2: ethernet-phy@2 {
- reg = <2>;
+ reg = <0x2>;
device_type = "ethernet-phy";
};
};
device_type = "network";
compatible = "fsl,mpc885-fec-enet",
"fsl,pq1-fec-enet";
- reg = <e00 188>;
+ reg = <0xe00 0x188>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <3 1>;
interrupt-parent = <&PIC>;
device_type = "network";
compatible = "fsl,mpc885-fec-enet",
"fsl,pq1-fec-enet";
- reg = <1e00 188>;
+ reg = <0x1e00 0x188>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <7 1>;
interrupt-parent = <&PIC>;
PIC: interrupt-controller@0 {
interrupt-controller;
#interrupt-cells = <2>;
- reg = <0 24>;
+ reg = <0x0 0x24>;
compatible = "fsl,mpc885-pic", "fsl,pq1-pic";
};
#size-cells = <2>;
compatible = "fsl,pq-pcmcia";
device_type = "pcmcia";
- reg = <80 80>;
+ reg = <0x80 0x80>;
interrupt-parent = <&PIC>;
- interrupts = <d 1>;
+ interrupts = <13 1>;
};
cpm@9c0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "fsl,mpc885-cpm", "fsl,cpm1";
- command-proc = <9c0>;
+ command-proc = <0x9c0>;
interrupts = <0>; // cpm error interrupt
interrupt-parent = <&CPM_PIC>;
- reg = <9c0 40>;
+ reg = <0x9c0 0x40>;
ranges;
muram@2000 {
#address-cells = <1>;
#size-cells = <1>;
- ranges = <0 2000 2000>;
+ ranges = <0x0 0x2000 0x2000>;
data@0 {
compatible = "fsl,cpm-muram-data";
- reg = <0 1c00>;
+ reg = <0x0 0x1c00>;
};
};
"fsl,cpm1-brg",
"fsl,cpm-brg";
clock-frequency = <0>;
- reg = <9f0 10>;
+ reg = <0x9f0 0x10>;
};
CPM_PIC: interrupt-controller@930 {
#interrupt-cells = <1>;
interrupts = <5 2 0 2>;
interrupt-parent = <&PIC>;
- reg = <930 20>;
+ reg = <0x930 0x20>;
compatible = "fsl,mpc885-cpm-pic",
"fsl,cpm1-pic";
};
device_type = "serial";
compatible = "fsl,mpc885-smc-uart",
"fsl,cpm1-smc-uart";
- reg = <a80 10 3e80 40>;
+ reg = <0xa80 0x10 0x3e80 0x40>;
interrupts = <4>;
interrupt-parent = <&CPM_PIC>;
fsl,cpm-brg = <1>;
- fsl,cpm-command = <0090>;
+ fsl,cpm-command = <0x90>;
};
serial@a90 {
device_type = "serial";
compatible = "fsl,mpc885-smc-uart",
"fsl,cpm1-smc-uart";
- reg = <a90 10 3f80 40>;
+ reg = <0xa90 0x10 0x3f80 0x40>;
interrupts = <3>;
interrupt-parent = <&CPM_PIC>;
fsl,cpm-brg = <2>;
- fsl,cpm-command = <00d0>;
+ fsl,cpm-command = <0xd0>;
};
ethernet@a40 {
device_type = "network";
compatible = "fsl,mpc885-scc-enet",
"fsl,cpm1-scc-enet";
- reg = <a40 18 3e00 100>;
+ reg = <0xa40 0x18 0x3e00 0x100>;
local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <1c>;
+ interrupts = <28>;
interrupt-parent = <&CPM_PIC>;
phy-handle = <&PHY2>;
- fsl,cpm-command = <0080>;
+ fsl,cpm-command = <0x80>;
linux,network-index = <2>;
};
};
/*
* Device Tree for the PQ2FADS-ZU board with an MPC8280 chip.
*
- * Copyright 2007 Freescale Semiconductor Inc.
+ * Copyright 2007,2008 Freescale Semiconductor Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* option) any later version.
*/
+/dts-v1/;
+
/ {
model = "pq2fads";
compatible = "fsl,pq2fads";
cpu@0 {
device_type = "cpu";
- reg = <0>;
- d-cache-line-size = <d#32>;
- i-cache-line-size = <d#32>;
- d-cache-size = <d#16384>;
- i-cache-size = <d#16384>;
+ reg = <0x0>;
+ d-cache-line-size = <32>;
+ i-cache-line-size = <32>;
+ d-cache-size = <16384>;
+ i-cache-size = <16384>;
timebase-frequency = <0>;
clock-frequency = <0>;
};
memory {
device_type = "memory";
- reg = <0 0>;
+ reg = <0x0 0x0>;
};
localbus@f0010100 {
"fsl,pq2-localbus";
#address-cells = <2>;
#size-cells = <1>;
- reg = <f0010100 60>;
+ reg = <0xf0010100 0x60>;
- ranges = <0 0 fe000000 00800000
- 1 0 f4500000 00008000
- 8 0 f8200000 00008000>;
+ ranges = <0x0 0x0 0xfe000000 0x800000
+ 0x1 0x0 0xf4500000 0x8000
+ 0x8 0x0 0xf8200000 0x8000>;
flash@0,0 {
compatible = "jedec-flash";
- reg = <0 0 800000>;
+ reg = <0x0 0x0 0x800000>;
bank-width = <4>;
device-width = <1>;
};
bcsr@1,0 {
- reg = <1 0 20>;
+ reg = <0x1 0x0 0x20>;
compatible = "fsl,pq2fads-bcsr";
};
PCI_PIC: pic@8,0 {
#interrupt-cells = <1>;
interrupt-controller;
- reg = <8 0 8>;
+ reg = <0x8 0x0 0x8>;
compatible = "fsl,pq2ads-pci-pic";
interrupt-parent = <&PIC>;
- interrupts = <18 8>;
+ interrupts = <24 8>;
};
};
pci@f0010800 {
device_type = "pci";
- reg = <f0010800 10c f00101ac 8 f00101c4 8>;
+ reg = <0xf0010800 0x10c 0xf00101ac 0x8 0xf00101c4 0x8>;
compatible = "fsl,mpc8280-pci", "fsl,pq2-pci";
#interrupt-cells = <1>;
#size-cells = <2>;
#address-cells = <3>;
- clock-frequency = <d#66000000>;
- interrupt-map-mask = <f800 0 0 7>;
+ clock-frequency = <66000000>;
+ interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
interrupt-map = <
/* IDSEL 0x16 */
- b000 0 0 1 &PCI_PIC 0
- b000 0 0 2 &PCI_PIC 1
- b000 0 0 3 &PCI_PIC 2
- b000 0 0 4 &PCI_PIC 3
+ 0xb000 0x0 0x0 0x1 &PCI_PIC 0
+ 0xb000 0x0 0x0 0x2 &PCI_PIC 1
+ 0xb000 0x0 0x0 0x3 &PCI_PIC 2
+ 0xb000 0x0 0x0 0x4 &PCI_PIC 3
/* IDSEL 0x17 */
- b800 0 0 1 &PCI_PIC 4
- b800 0 0 2 &PCI_PIC 5
- b800 0 0 3 &PCI_PIC 6
- b800 0 0 4 &PCI_PIC 7
+ 0xb800 0x0 0x0 0x1 &PCI_PIC 4
+ 0xb800 0x0 0x0 0x2 &PCI_PIC 5
+ 0xb800 0x0 0x0 0x3 &PCI_PIC 6
+ 0xb800 0x0 0x0 0x4 &PCI_PIC 7
/* IDSEL 0x18 */
- c000 0 0 1 &PCI_PIC 8
- c000 0 0 2 &PCI_PIC 9
- c000 0 0 3 &PCI_PIC a
- c000 0 0 4 &PCI_PIC b>;
+ 0xc000 0x0 0x0 0x1 &PCI_PIC 8
+ 0xc000 0x0 0x0 0x2 &PCI_PIC 9
+ 0xc000 0x0 0x0 0x3 &PCI_PIC 10
+ 0xc000 0x0 0x0 0x4 &PCI_PIC 11>;
interrupt-parent = <&PIC>;
- interrupts = <12 8>;
- ranges = <42000000 0 80000000 80000000 0 20000000
- 02000000 0 a0000000 a0000000 0 20000000
- 01000000 0 00000000 f6000000 0 02000000>;
+ interrupts = <18 8>;
+ ranges = <0x42000000 0x0 0x80000000 0x80000000 0x0 0x20000000
+ 0x2000000 0x0 0xa0000000 0xa0000000 0x0 0x20000000
+ 0x1000000 0x0 0x0 0xf6000000 0x0 0x2000000>;
};
soc@f0000000 {
#size-cells = <1>;
device_type = "soc";
compatible = "fsl,mpc8280", "fsl,pq2-soc";
- ranges = <00000000 f0000000 00053000>;
+ ranges = <0x0 0xf0000000 0x53000>;
// Temporary -- will go away once kernel uses ranges for get_immrbase().
- reg = <f0000000 00053000>;
+ reg = <0xf0000000 0x53000>;
cpm@119c0 {
#address-cells = <1>;
#size-cells = <1>;
#interrupt-cells = <2>;
compatible = "fsl,mpc8280-cpm", "fsl,cpm2";
- reg = <119c0 30>;
+ reg = <0x119c0 0x30>;
ranges;
muram@0 {
#address-cells = <1>;
#size-cells = <1>;
- ranges = <0 0 10000>;
+ ranges = <0x0 0x0 0x10000>;
data@0 {
compatible = "fsl,cpm-muram-data";
- reg = <0 2000 9800 800>;
+ reg = <0x0 0x2000 0x9800 0x800>;
};
};
compatible = "fsl,mpc8280-brg",
"fsl,cpm2-brg",
"fsl,cpm-brg";
- reg = <119f0 10 115f0 10>;
+ reg = <0x119f0 0x10 0x115f0 0x10>;
};
serial@11a00 {
device_type = "serial";
compatible = "fsl,mpc8280-scc-uart",
"fsl,cpm2-scc-uart";
- reg = <11a00 20 8000 100>;
- interrupts = <28 8>;
+ reg = <0x11a00 0x20 0x8000 0x100>;
+ interrupts = <40 8>;
interrupt-parent = <&PIC>;
fsl,cpm-brg = <1>;
- fsl,cpm-command = <00800000>;
+ fsl,cpm-command = <0x800000>;
};
serial@11a20 {
device_type = "serial";
compatible = "fsl,mpc8280-scc-uart",
"fsl,cpm2-scc-uart";
- reg = <11a20 20 8100 100>;
- interrupts = <29 8>;
+ reg = <0x11a20 0x20 0x8100 0x100>;
+ interrupts = <41 8>;
interrupt-parent = <&PIC>;
fsl,cpm-brg = <2>;
- fsl,cpm-command = <04a00000>;
+ fsl,cpm-command = <0x4a00000>;
};
ethernet@11320 {
device_type = "network";
compatible = "fsl,mpc8280-fcc-enet",
"fsl,cpm2-fcc-enet";
- reg = <11320 20 8500 100 113b0 1>;
- interrupts = <21 8>;
+ reg = <0x11320 0x20 0x8500 0x100 0x113b0 0x1>;
+ interrupts = <33 8>;
interrupt-parent = <&PIC>;
phy-handle = <&PHY0>;
linux,network-index = <0>;
- fsl,cpm-command = <16200300>;
+ fsl,cpm-command = <0x16200300>;
};
ethernet@11340 {
device_type = "network";
compatible = "fsl,mpc8280-fcc-enet",
"fsl,cpm2-fcc-enet";
- reg = <11340 20 8600 100 113d0 1>;
- interrupts = <22 8>;
+ reg = <0x11340 0x20 0x8600 0x100 0x113d0 0x1>;
+ interrupts = <34 8>;
interrupt-parent = <&PIC>;
phy-handle = <&PHY1>;
linux,network-index = <1>;
- fsl,cpm-command = <1a400300>;
+ fsl,cpm-command = <0x1a400300>;
local-mac-address = [00 e0 0c 00 79 01];
};
"fsl,cpm2-mdio-bitbang";
#address-cells = <1>;
#size-cells = <0>;
- reg = <10d40 14>;
+ reg = <0x10d40 0x14>;
fsl,mdio-pin = <9>;
- fsl,mdc-pin = <a>;
+ fsl,mdc-pin = <10>;
PHY0: ethernet-phy@0 {
interrupt-parent = <&PIC>;
- interrupts = <19 2>;
- reg = <0>;
+ interrupts = <25 2>;
+ reg = <0x0>;
device_type = "ethernet-phy";
};
PHY1: ethernet-phy@1 {
interrupt-parent = <&PIC>;
- interrupts = <19 2>;
- reg = <3>;
+ interrupts = <25 2>;
+ reg = <0x3>;
device_type = "ethernet-phy";
};
};
#size-cells = <0>;
compatible = "fsl,mpc8280-usb",
"fsl,cpm2-usb";
- reg = <11b60 18 8b00 100>;
+ reg = <0x11b60 0x18 0x8b00 0x100>;
interrupt-parent = <&PIC>;
- interrupts = <b 8>;
- fsl,cpm-command = <2e600000>;
+ interrupts = <11 8>;
+ fsl,cpm-command = <0x2e600000>;
};
};
PIC: interrupt-controller@10c00 {
#interrupt-cells = <2>;
interrupt-controller;
- reg = <10c00 80>;
+ reg = <0x10c00 0x80>;
compatible = "fsl,mpc8280-pic", "fsl,cpm2-pic";
};
--- /dev/null
+/*
+ * SBC8641D Device Tree Source
+ *
+ * Copyright 2008 Wind River Systems Inc.
+ *
+ * Paul Gortmaker (see MAINTAINERS for contact information)
+ *
+ * Based largely on the mpc8641_hpcn.dts by Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+/dts-v1/;
+
+/ {
+ model = "SBC8641D";
+ compatible = "wind,sbc8641";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ aliases {
+ ethernet0 = &enet0;
+ ethernet1 = &enet1;
+ ethernet2 = &enet2;
+ ethernet3 = &enet3;
+ serial0 = &serial0;
+ serial1 = &serial1;
+ pci0 = &pci0;
+ pci1 = &pci1;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ PowerPC,8641@0 {
+ device_type = "cpu";
+ reg = <0>;
+ d-cache-line-size = <32>;
+ i-cache-line-size = <32>;
+ d-cache-size = <32768>; // L1
+ i-cache-size = <32768>; // L1
+ timebase-frequency = <0>; // From uboot
+ bus-frequency = <0>; // From uboot
+ clock-frequency = <0>; // From uboot
+ };
+ PowerPC,8641@1 {
+ device_type = "cpu";
+ reg = <1>;
+ d-cache-line-size = <32>;
+ i-cache-line-size = <32>;
+ d-cache-size = <32768>;
+ i-cache-size = <32768>;
+ timebase-frequency = <0>; // From uboot
+ bus-frequency = <0>; // From uboot
+ clock-frequency = <0>; // From uboot
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x20000000>; // 512M at 0x0
+ };
+
+ localbus@f8005000 {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8641-localbus", "simple-bus";
+ reg = <0xf8005000 0x1000>;
+ interrupts = <19 2>;
+ interrupt-parent = <&mpic>;
+
+ ranges = <0 0 0xff000000 0x01000000 // 16MB Boot flash
+ 1 0 0xf0000000 0x00010000 // 64KB EEPROM
+ 2 0 0xf1000000 0x00100000 // EPLD (1MB)
+ 3 0 0xe0000000 0x04000000 // 64MB LB SDRAM (CS3)
+ 4 0 0xe4000000 0x04000000 // 64MB LB SDRAM (CS4)
+ 6 0 0xf4000000 0x00100000 // LCD display (1MB)
+ 7 0 0xe8000000 0x04000000>; // 64MB OneNAND
+
+ flash@0,0 {
+ compatible = "cfi-flash";
+ reg = <0 0 0x01000000>;
+ bank-width = <2>;
+ device-width = <2>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ partition@0 {
+ label = "dtb";
+ reg = <0x00000000 0x00100000>;
+ read-only;
+ };
+ partition@300000 {
+ label = "kernel";
+ reg = <0x00100000 0x00400000>;
+ read-only;
+ };
+ partition@400000 {
+ label = "fs";
+ reg = <0x00500000 0x00a00000>;
+ };
+ partition@700000 {
+ label = "firmware";
+ reg = <0x00f00000 0x00100000>;
+ read-only;
+ };
+ };
+
+ epld@2,0 {
+ compatible = "wrs,epld-localbus";
+ #address-cells = <2>;
+ #size-cells = <1>;
+ reg = <2 0 0x100000>;
+ ranges = <0 0 5 0 1 // User switches
+ 1 0 5 1 1 // Board ID/Rev
+ 3 0 5 3 1>; // LEDs
+ };
+ };
+
+ soc@f8000000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "soc";
+ compatible = "simple-bus";
+ ranges = <0x00000000 0xf8000000 0x00100000>;
+ reg = <0xf8000000 0x00001000>; // CCSRBAR
+ bus-frequency = <0>;
+
+ i2c@3000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <0>;
+ compatible = "fsl-i2c";
+ reg = <0x3000 0x100>;
+ interrupts = <43 2>;
+ interrupt-parent = <&mpic>;
+ dfsrr;
+ };
+
+ i2c@3100 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <1>;
+ compatible = "fsl-i2c";
+ reg = <0x3100 0x100>;
+ interrupts = <43 2>;
+ interrupt-parent = <&mpic>;
+ dfsrr;
+ };
+
+ mdio@24520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x24520 0x20>;
+
+ phy0: ethernet-phy@1f {
+ interrupt-parent = <&mpic>;
+ interrupts = <10 1>;
+ reg = <0x1f>;
+ device_type = "ethernet-phy";
+ };
+ phy1: ethernet-phy@0 {
+ interrupt-parent = <&mpic>;
+ interrupts = <10 1>;
+ reg = <0>;
+ device_type = "ethernet-phy";
+ };
+ phy2: ethernet-phy@1 {
+ interrupt-parent = <&mpic>;
+ interrupts = <10 1>;
+ reg = <1>;
+ device_type = "ethernet-phy";
+ };
+ phy3: ethernet-phy@2 {
+ interrupt-parent = <&mpic>;
+ interrupts = <10 1>;
+ reg = <2>;
+ device_type = "ethernet-phy";
+ };
+ };
+
+ enet0: ethernet@24000 {
+ cell-index = <0>;
+ device_type = "network";
+ model = "TSEC";
+ compatible = "gianfar";
+ reg = <0x24000 0x1000>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <29 2 30 2 34 2>;
+ interrupt-parent = <&mpic>;
+ phy-handle = <&phy0>;
+ phy-connection-type = "rgmii-id";
+ };
+
+ enet1: ethernet@25000 {
+ cell-index = <1>;
+ device_type = "network";
+ model = "TSEC";
+ compatible = "gianfar";
+ reg = <0x25000 0x1000>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <35 2 36 2 40 2>;
+ interrupt-parent = <&mpic>;
+ phy-handle = <&phy1>;
+ phy-connection-type = "rgmii-id";
+ };
+
+ enet2: ethernet@26000 {
+ cell-index = <2>;
+ device_type = "network";
+ model = "TSEC";
+ compatible = "gianfar";
+ reg = <0x26000 0x1000>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <31 2 32 2 33 2>;
+ interrupt-parent = <&mpic>;
+ phy-handle = <&phy2>;
+ phy-connection-type = "rgmii-id";
+ };
+
+ enet3: ethernet@27000 {
+ cell-index = <3>;
+ device_type = "network";
+ model = "TSEC";
+ compatible = "gianfar";
+ reg = <0x27000 0x1000>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <37 2 38 2 39 2>;
+ interrupt-parent = <&mpic>;
+ phy-handle = <&phy3>;
+ phy-connection-type = "rgmii-id";
+ };
+
+ serial0: serial@4500 {
+ cell-index = <0>;
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <0x4500 0x100>;
+ clock-frequency = <0>;
+ interrupts = <42 2>;
+ interrupt-parent = <&mpic>;
+ };
+
+ serial1: serial@4600 {
+ cell-index = <1>;
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <0x4600 0x100>;
+ clock-frequency = <0>;
+ interrupts = <28 2>;
+ interrupt-parent = <&mpic>;
+ };
+
+ mpic: pic@40000 {
+ clock-frequency = <0>;
+ interrupt-controller;
+ #address-cells = <0>;
+ #interrupt-cells = <2>;
+ reg = <0x40000 0x40000>;
+ compatible = "chrp,open-pic";
+ device_type = "open-pic";
+ big-endian;
+ };
+
+ global-utilities@e0000 {
+ compatible = "fsl,mpc8641-guts";
+ reg = <0xe0000 0x1000>;
+ fsl,has-rstcr;
+ };
+ };
+
+ pci0: pcie@f8008000 {
+ cell-index = <0>;
+ compatible = "fsl,mpc8641-pcie";
+ device_type = "pci";
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ reg = <0xf8008000 0x1000>;
+ bus-range = <0x0 0xff>;
+ ranges = <0x02000000 0x0 0x80000000 0x80000000 0x0 0x20000000
+ 0x01000000 0x0 0x00000000 0xe2000000 0x0 0x00100000>;
+ clock-frequency = <33333333>;
+ interrupt-parent = <&mpic>;
+ interrupts = <24 2>;
+ interrupt-map-mask = <0xff00 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0x0000 0 0 1 &mpic 0 1
+ 0x0000 0 0 2 &mpic 1 1
+ 0x0000 0 0 3 &mpic 2 1
+ 0x0000 0 0 4 &mpic 3 1
+ >;
+
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ ranges = <0x02000000 0x0 0x80000000
+ 0x02000000 0x0 0x80000000
+ 0x0 0x20000000
+
+ 0x01000000 0x0 0x00000000
+ 0x01000000 0x0 0x00000000
+ 0x0 0x00100000>;
+ };
+
+ };
+
+ pci1: pcie@f8009000 {
+ cell-index = <1>;
+ compatible = "fsl,mpc8641-pcie";
+ device_type = "pci";
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ reg = <0xf8009000 0x1000>;
+ bus-range = <0 0xff>;
+ ranges = <0x02000000 0x0 0xa0000000 0xa0000000 0x0 0x20000000
+ 0x01000000 0x0 0x00000000 0xe3000000 0x0 0x00100000>;
+ clock-frequency = <33333333>;
+ interrupt-parent = <&mpic>;
+ interrupts = <25 2>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0x0000 0 0 1 &mpic 4 1
+ 0x0000 0 0 2 &mpic 5 1
+ 0x0000 0 0 3 &mpic 6 1
+ 0x0000 0 0 4 &mpic 7 1
+ >;
+
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ ranges = <0x02000000 0x0 0xa0000000
+ 0x02000000 0x0 0xa0000000
+ 0x0 0x20000000
+
+ 0x01000000 0x0 0x00000000
+ 0x01000000 0x0 0x00000000
+ 0x0 0x00100000>;
+ };
+ };
+};
int mpc5200_psc_console_init(void *devp, struct serial_console_data *scdp)
{
- int n;
-
/* Get the base address of the psc registers */
- n = getprop(devp, "virtual-reg", &psc, sizeof(psc));
- if (n != sizeof(psc)) {
- if (!dt_xlate_reg(devp, 0, (void *)&psc, NULL))
- return -1;
- }
+ if (dt_get_virtual_reg(devp, &psc, 1) < 1)
+ return -1;
scdp->open = psc_open;
scdp->putc = psc_putc;
int ns16550_console_init(void *devp, struct serial_console_data *scdp)
{
int n;
- unsigned long reg_phys;
- n = getprop(devp, "virtual-reg", ®_base, sizeof(reg_base));
- if (n != sizeof(reg_base)) {
- if (!dt_xlate_reg(devp, 0, ®_phys, NULL))
- return -1;
-
- reg_base = (void *)reg_phys;
- }
+ if (dt_get_virtual_reg(devp, (void **)®_base, 1) < 1)
+ return -1;
n = getprop(devp, "reg-shift", ®_shift, sizeof(reg_shift));
if (n != sizeof(reg_shift))
int dt_xlate_addr(void *node, u32 *buf, int buflen, unsigned long *xlated_addr);
int dt_is_compatible(void *node, const char *compat);
void dt_get_reg_format(void *node, u32 *naddr, u32 *nsize);
+int dt_get_virtual_reg(void *node, void **addr, int nres);
static inline void *finddevice(const char *name)
{
#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.25-rc6
-# Mon Mar 24 08:48:14 2008
+# Fri Apr 11 11:10:09 2008
#
# CONFIG_PPC64 is not set
# CONFIG_PREEMPT is not set
CONFIG_BINFMT_ELF=y
# CONFIG_BINFMT_MISC is not set
+CONFIG_FORCE_MAX_ZONEORDER=11
# CONFIG_IOMMU_HELPER is not set
CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
CONFIG_ARCH_HAS_WALK_MEMORY=y
CONFIG_MTD_PARTITIONS=y
# CONFIG_MTD_REDBOOT_PARTS is not set
# CONFIG_MTD_CMDLINE_PARTS is not set
-# CONFIG_MTD_OF_PARTS is not set
+CONFIG_MTD_OF_PARTS=y
#
# User Modules And Translation Layers
# CONFIG_MTD_NAND_NANDSIM is not set
# CONFIG_MTD_NAND_PLATFORM is not set
# CONFIG_MTD_ALAUDA is not set
-# CONFIG_MTD_NAND_FSL_ELBC is not set
+CONFIG_MTD_NAND_FSL_ELBC=y
# CONFIG_MTD_ONENAND is not set
#
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
#
# Kernel hacking
# CONFIG_MPC85xx_CDS is not set
# CONFIG_MPC85xx_MDS is not set
CONFIG_MPC85xx_DS=y
+# CONFIG_KSI8560 is not set
# CONFIG_STX_GP3 is not set
# CONFIG_TQM8540 is not set
# CONFIG_TQM8541 is not set
# CONFIG_PREEMPT is not set
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_MISC=m
+CONFIG_FORCE_MAX_ZONEORDER=11
CONFIG_MATH_EMULATION=y
# CONFIG_IOMMU_HELPER is not set
CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
#
# on-CPU RTC drivers
#
-# CONFIG_DMADEVICES is not set
+CONFIG_DMADEVICES=y
+
+#
+# DMA Devices
+#
+CONFIG_FSL_DMA=y
+# CONFIG_FSL_DMA_SELFTEST is not set
+CONFIG_DMA_ENGINE=y
+
+#
+# DMA Clients
+#
+# CONFIG_NET_DMA is not set
#
# Userspace I/O
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
#
# Kernel hacking
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.25-rc6
-# Mon Mar 24 08:48:25 2008
+# Linux kernel version: 2.6.25-rc9
+# Tue Apr 15 18:07:36 2008
#
# CONFIG_PPC64 is not set
# CONFIG_PREEMPT is not set
CONFIG_BINFMT_ELF=y
# CONFIG_BINFMT_MISC is not set
+CONFIG_FORCE_MAX_ZONEORDER=11
CONFIG_MATH_EMULATION=y
# CONFIG_IOMMU_HELPER is not set
CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
# CONFIG_FW_LOADER is not set
# CONFIG_SYS_HYPERVISOR is not set
# CONFIG_CONNECTOR is not set
-# CONFIG_MTD is not set
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_CONCAT is not set
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_REDBOOT_PARTS is not set
+# CONFIG_MTD_CMDLINE_PARTS is not set
+CONFIG_MTD_OF_PARTS=y
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
+# CONFIG_MTD_OOPS is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+CONFIG_MTD_CFI=y
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_GEN_PROBE=y
+# CONFIG_MTD_CFI_ADV_OPTIONS is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+# CONFIG_MTD_CFI_INTELEXT is not set
+CONFIG_MTD_CFI_AMDSTD=y
+# CONFIG_MTD_CFI_STAA is not set
+CONFIG_MTD_CFI_UTIL=y
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+# CONFIG_MTD_PHYSMAP is not set
+CONFIG_MTD_PHYSMAP_OF=y
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_VERIFY_WRITE=y
+# CONFIG_MTD_NAND_ECC_SMC is not set
+# CONFIG_MTD_NAND_MUSEUM_IDS is not set
+CONFIG_MTD_NAND_IDS=y
+# CONFIG_MTD_NAND_DISKONCHIP is not set
+# CONFIG_MTD_NAND_NANDSIM is not set
+# CONFIG_MTD_NAND_PLATFORM is not set
+# CONFIG_MTD_ALAUDA is not set
+CONFIG_MTD_NAND_FSL_ELBC=y
+# CONFIG_MTD_ONENAND is not set
+
+#
+# UBI - Unsorted block images
+#
+# CONFIG_MTD_UBI is not set
CONFIG_OF_DEVICE=y
# CONFIG_PARPORT is not set
CONFIG_BLK_DEV=y
CONFIG_BLK_DEV_LOOP=y
# CONFIG_BLK_DEV_CRYPTOLOOP is not set
# CONFIG_BLK_DEV_NBD is not set
+# CONFIG_BLK_DEV_UB is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=32768
#
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
+
+#
+# USB Network Adapters
+#
+# CONFIG_USB_CATC is not set
+# CONFIG_USB_KAWETH is not set
+# CONFIG_USB_PEGASUS is not set
+# CONFIG_USB_RTL8150 is not set
+# CONFIG_USB_USBNET is not set
# CONFIG_WAN is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
# CONFIG_I2C_SIMTEC is not set
# CONFIG_I2C_TAOS_EVM is not set
# CONFIG_I2C_STUB is not set
+# CONFIG_I2C_TINY_USB is not set
#
# Miscellaneous I2C Chip support
# CONFIG_SOFT_WATCHDOG is not set
CONFIG_83xx_WDT=y
+#
+# USB-based Watchdog Cards
+#
+# CONFIG_USBPCWATCHDOG is not set
+
#
# Sonics Silicon Backplane
#
# CONFIG_VIDEO_DEV is not set
# CONFIG_DVB_CORE is not set
CONFIG_DAB=y
+# CONFIG_USB_DABUSB is not set
#
# Graphics support
CONFIG_HID=y
# CONFIG_HID_DEBUG is not set
# CONFIG_HIDRAW is not set
+
+#
+# USB Input Devices
+#
+CONFIG_USB_HID=y
+# CONFIG_USB_HIDINPUT_POWERBOOK is not set
+# CONFIG_HID_FF is not set
+# CONFIG_USB_HIDDEV is not set
CONFIG_USB_SUPPORT=y
CONFIG_USB_ARCH_HAS_HCD=y
# CONFIG_USB_ARCH_HAS_OHCI is not set
# CONFIG_USB_SL811_HCD is not set
# CONFIG_USB_R8A66597_HCD is not set
+#
+# USB Device Class drivers
+#
+# CONFIG_USB_ACM is not set
+# CONFIG_USB_PRINTER is not set
+
#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
#
+
+#
+# may also be needed; see USB_STORAGE Help for more information
+#
+# CONFIG_USB_STORAGE is not set
+# CONFIG_USB_LIBUSUAL is not set
+
+#
+# USB Imaging devices
+#
+# CONFIG_USB_MDC800 is not set
+# CONFIG_USB_MICROTEK is not set
+CONFIG_USB_MON=y
+
+#
+# USB port drivers
+#
+# CONFIG_USB_SERIAL is not set
+
+#
+# USB Miscellaneous drivers
+#
+# CONFIG_USB_EMI62 is not set
+# CONFIG_USB_EMI26 is not set
+# CONFIG_USB_ADUTUX is not set
+# CONFIG_USB_AUERSWALD is not set
+# CONFIG_USB_RIO500 is not set
+# CONFIG_USB_LEGOTOWER is not set
+# CONFIG_USB_LCD is not set
+# CONFIG_USB_BERRY_CHARGE is not set
+# CONFIG_USB_LED is not set
+# CONFIG_USB_CYPRESS_CY7C63 is not set
+# CONFIG_USB_CYTHERM is not set
+# CONFIG_USB_PHIDGET is not set
+# CONFIG_USB_IDMOUSE is not set
+# CONFIG_USB_FTDI_ELAN is not set
+# CONFIG_USB_APPLEDISPLAY is not set
+# CONFIG_USB_SISUSBVGA is not set
+# CONFIG_USB_LD is not set
+# CONFIG_USB_TRANCEVIBRATOR is not set
+# CONFIG_USB_IOWARRIOR is not set
# CONFIG_USB_GADGET is not set
# CONFIG_MMC is not set
# CONFIG_MEMSTICK is not set
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
+# CONFIG_JFFS2_FS is not set
# CONFIG_CRAMFS is not set
# CONFIG_VXFS_FS is not set
# CONFIG_MINIX_FS is not set
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
#
# Kernel hacking
--- /dev/null
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.25-rc6
+# Thu Apr 10 18:03:25 2008
+#
+# CONFIG_PPC64 is not set
+
+#
+# Processor support
+#
+CONFIG_6xx=y
+# CONFIG_PPC_85xx is not set
+# CONFIG_PPC_8xx is not set
+# CONFIG_40x is not set
+# CONFIG_44x is not set
+# CONFIG_E200 is not set
+CONFIG_PPC_FPU=y
+CONFIG_ALTIVEC=y
+CONFIG_PPC_STD_MMU=y
+CONFIG_PPC_STD_MMU_32=y
+# CONFIG_PPC_MM_SLICES is not set
+CONFIG_SMP=y
+CONFIG_NR_CPUS=2
+CONFIG_PPC32=y
+CONFIG_WORD_SIZE=32
+CONFIG_PPC_MERGE=y
+CONFIG_MMU=y
+CONFIG_GENERIC_CMOS_UPDATE=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_TIME_VSYSCALL=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_HARDIRQS=y
+# CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
+CONFIG_IRQ_PER_CPU=y
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_GENERIC_LOCKBREAK=y
+CONFIG_ARCH_HAS_ILOG2_U32=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_FIND_NEXT_BIT=y
+# CONFIG_ARCH_NO_VIRT_TO_BUS is not set
+CONFIG_PPC=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_GENERIC_NVRAM=y
+CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
+CONFIG_ARCH_MAY_HAVE_PC_FDC=y
+CONFIG_PPC_OF=y
+CONFIG_OF=y
+CONFIG_PPC_UDBG_16550=y
+CONFIG_GENERIC_TBSYNC=y
+CONFIG_AUDIT_ARCH=y
+CONFIG_GENERIC_BUG=y
+CONFIG_DEFAULT_UIMAGE=y
+# CONFIG_PPC_DCR_NATIVE is not set
+# CONFIG_PPC_DCR_MMIO is not set
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+
+#
+# General setup
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_LOCK_KERNEL=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_BSD_PROCESS_ACCT=y
+CONFIG_BSD_PROCESS_ACCT_V3=y
+# CONFIG_TASKSTATS is not set
+# CONFIG_AUDIT is not set
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
+# CONFIG_CGROUPS is not set
+CONFIG_GROUP_SCHED=y
+CONFIG_FAIR_GROUP_SCHED=y
+# CONFIG_RT_GROUP_SCHED is not set
+CONFIG_USER_SCHED=y
+# CONFIG_CGROUP_SCHED is not set
+CONFIG_SYSFS_DEPRECATED=y
+CONFIG_SYSFS_DEPRECATED_V2=y
+CONFIG_RELAY=y
+# CONFIG_NAMESPACES is not set
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_INITRAMFS_SOURCE=""
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_SYSCTL=y
+CONFIG_EMBEDDED=y
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_KALLSYMS=y
+# CONFIG_KALLSYMS_ALL is not set
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_COMPAT_BRK=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
+CONFIG_SHMEM=y
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_SLAB=y
+# CONFIG_SLUB is not set
+# CONFIG_SLOB is not set
+# CONFIG_PROFILING is not set
+# CONFIG_MARKERS is not set
+CONFIG_HAVE_OPROFILE=y
+# CONFIG_KPROBES is not set
+CONFIG_HAVE_KPROBES=y
+CONFIG_HAVE_KRETPROBES=y
+CONFIG_PROC_PAGE_MONITOR=y
+CONFIG_SLABINFO=y
+CONFIG_RT_MUTEXES=y
+# CONFIG_TINY_SHMEM is not set
+CONFIG_BASE_SMALL=0
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_MODULE_FORCE_UNLOAD is not set
+# CONFIG_MODVERSIONS is not set
+# CONFIG_MODULE_SRCVERSION_ALL is not set
+CONFIG_KMOD=y
+CONFIG_STOP_MACHINE=y
+CONFIG_BLOCK=y
+# CONFIG_LBD is not set
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_LSF is not set
+# CONFIG_BLK_DEV_BSG is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_AS=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+# CONFIG_DEFAULT_AS is not set
+# CONFIG_DEFAULT_DEADLINE is not set
+CONFIG_DEFAULT_CFQ=y
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="cfq"
+CONFIG_CLASSIC_RCU=y
+
+#
+# Platform support
+#
+# CONFIG_PPC_MULTIPLATFORM is not set
+# CONFIG_PPC_82xx is not set
+# CONFIG_PPC_83xx is not set
+CONFIG_PPC_86xx=y
+# CONFIG_PPC_MPC512x is not set
+# CONFIG_PPC_MPC5121 is not set
+# CONFIG_PPC_CELL is not set
+# CONFIG_PPC_CELL_NATIVE is not set
+# CONFIG_PQ2ADS is not set
+# CONFIG_MPC8641_HPCN is not set
+CONFIG_SBC8641D=y
+# CONFIG_MPC8610_HPCD is not set
+CONFIG_MPC8641=y
+# CONFIG_IPIC is not set
+CONFIG_MPIC=y
+# CONFIG_MPIC_WEIRD is not set
+# CONFIG_PPC_I8259 is not set
+# CONFIG_PPC_RTAS is not set
+# CONFIG_MMIO_NVRAM is not set
+# CONFIG_PPC_MPC106 is not set
+# CONFIG_PPC_970_NAP is not set
+# CONFIG_PPC_INDIRECT_IO is not set
+# CONFIG_GENERIC_IOMAP is not set
+# CONFIG_CPU_FREQ is not set
+# CONFIG_FSL_ULI1575 is not set
+
+#
+# Kernel options
+#
+# CONFIG_HIGHMEM is not set
+CONFIG_TICK_ONESHOT=y
+# CONFIG_NO_HZ is not set
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+# CONFIG_HZ_100 is not set
+CONFIG_HZ_250=y
+# CONFIG_HZ_300 is not set
+# CONFIG_HZ_1000 is not set
+CONFIG_HZ=250
+# CONFIG_SCHED_HRTICK is not set
+# CONFIG_PREEMPT_NONE is not set
+# CONFIG_PREEMPT_VOLUNTARY is not set
+CONFIG_PREEMPT=y
+# CONFIG_PREEMPT_RCU is not set
+CONFIG_BINFMT_ELF=y
+CONFIG_BINFMT_MISC=m
+CONFIG_FORCE_MAX_ZONEORDER=11
+# CONFIG_IOMMU_HELPER is not set
+CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
+CONFIG_ARCH_HAS_WALK_MEMORY=y
+CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
+CONFIG_IRQ_ALL_CPUS=y
+CONFIG_ARCH_FLATMEM_ENABLE=y
+CONFIG_ARCH_POPULATES_NODE_MAP=y
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+# CONFIG_SPARSEMEM_STATIC is not set
+# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
+CONFIG_SPLIT_PTLOCK_CPUS=4
+# CONFIG_RESOURCES_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=1
+CONFIG_BOUNCE=y
+CONFIG_VIRT_TO_BUS=y
+# CONFIG_PROC_DEVICETREE is not set
+# CONFIG_CMDLINE_BOOL is not set
+# CONFIG_PM is not set
+CONFIG_SECCOMP=y
+CONFIG_ISA_DMA_API=y
+
+#
+# Bus options
+#
+CONFIG_ZONE_DMA=y
+CONFIG_GENERIC_ISA_DMA=y
+CONFIG_PPC_INDIRECT_PCI=y
+CONFIG_FSL_SOC=y
+CONFIG_FSL_PCI=y
+CONFIG_PCI=y
+CONFIG_PCI_DOMAINS=y
+CONFIG_PCI_SYSCALL=y
+CONFIG_PCIEPORTBUS=y
+CONFIG_PCIEAER=y
+CONFIG_ARCH_SUPPORTS_MSI=y
+# CONFIG_PCI_MSI is not set
+CONFIG_PCI_LEGACY=y
+# CONFIG_PCI_DEBUG is not set
+# CONFIG_PCCARD is not set
+# CONFIG_HOTPLUG_PCI is not set
+
+#
+# Advanced setup
+#
+# CONFIG_ADVANCED_OPTIONS is not set
+
+#
+# Default settings for advanced configuration options are used
+#
+CONFIG_HIGHMEM_START=0xfe000000
+CONFIG_LOWMEM_SIZE=0x30000000
+CONFIG_KERNEL_START=0xc0000000
+CONFIG_TASK_SIZE=0xc0000000
+CONFIG_BOOT_LOAD=0x00800000
+
+#
+# Networking
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+CONFIG_PACKET_MMAP=y
+CONFIG_UNIX=y
+CONFIG_XFRM=y
+CONFIG_XFRM_USER=m
+# CONFIG_XFRM_SUB_POLICY is not set
+# CONFIG_XFRM_MIGRATE is not set
+# CONFIG_XFRM_STATISTICS is not set
+CONFIG_NET_KEY=m
+# CONFIG_NET_KEY_MIGRATE is not set
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_ADVANCED_ROUTER=y
+CONFIG_ASK_IP_FIB_HASH=y
+# CONFIG_IP_FIB_TRIE is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_MULTIPLE_TABLES=y
+CONFIG_IP_ROUTE_MULTIPATH=y
+CONFIG_IP_ROUTE_VERBOSE=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_IP_PNP_RARP=y
+CONFIG_NET_IPIP=m
+CONFIG_NET_IPGRE=m
+CONFIG_NET_IPGRE_BROADCAST=y
+CONFIG_IP_MROUTE=y
+CONFIG_IP_PIMSM_V1=y
+CONFIG_IP_PIMSM_V2=y
+# CONFIG_ARPD is not set
+CONFIG_SYN_COOKIES=y
+CONFIG_INET_AH=m
+CONFIG_INET_ESP=m
+CONFIG_INET_IPCOMP=m
+CONFIG_INET_XFRM_TUNNEL=m
+CONFIG_INET_TUNNEL=m
+CONFIG_INET_XFRM_MODE_TRANSPORT=y
+CONFIG_INET_XFRM_MODE_TUNNEL=y
+CONFIG_INET_XFRM_MODE_BEET=y
+# CONFIG_INET_LRO is not set
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IP_VS is not set
+CONFIG_IPV6=m
+# CONFIG_IPV6_PRIVACY is not set
+# CONFIG_IPV6_ROUTER_PREF is not set
+# CONFIG_IPV6_OPTIMISTIC_DAD is not set
+CONFIG_INET6_AH=m
+CONFIG_INET6_ESP=m
+CONFIG_INET6_IPCOMP=m
+# CONFIG_IPV6_MIP6 is not set
+CONFIG_INET6_XFRM_TUNNEL=m
+CONFIG_INET6_TUNNEL=m
+CONFIG_INET6_XFRM_MODE_TRANSPORT=m
+CONFIG_INET6_XFRM_MODE_TUNNEL=m
+CONFIG_INET6_XFRM_MODE_BEET=m
+# CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION is not set
+CONFIG_IPV6_SIT=m
+CONFIG_IPV6_TUNNEL=m
+# CONFIG_IPV6_MULTIPLE_TABLES is not set
+# CONFIG_NETLABEL is not set
+# CONFIG_NETWORK_SECMARK is not set
+CONFIG_NETFILTER=y
+# CONFIG_NETFILTER_DEBUG is not set
+CONFIG_NETFILTER_ADVANCED=y
+CONFIG_BRIDGE_NETFILTER=y
+
+#
+# Core Netfilter Configuration
+#
+# CONFIG_NETFILTER_NETLINK_QUEUE is not set
+# CONFIG_NETFILTER_NETLINK_LOG is not set
+# CONFIG_NF_CONNTRACK is not set
+CONFIG_NETFILTER_XTABLES=m
+# CONFIG_NETFILTER_XT_TARGET_CLASSIFY is not set
+# CONFIG_NETFILTER_XT_TARGET_DSCP is not set
+# CONFIG_NETFILTER_XT_TARGET_MARK is not set
+# CONFIG_NETFILTER_XT_TARGET_NFQUEUE is not set
+# CONFIG_NETFILTER_XT_TARGET_NFLOG is not set
+# CONFIG_NETFILTER_XT_TARGET_RATEEST is not set
+# CONFIG_NETFILTER_XT_TARGET_TRACE is not set
+# CONFIG_NETFILTER_XT_TARGET_TCPMSS is not set
+# CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP is not set
+# CONFIG_NETFILTER_XT_MATCH_COMMENT is not set
+# CONFIG_NETFILTER_XT_MATCH_DCCP is not set
+# CONFIG_NETFILTER_XT_MATCH_DSCP is not set
+# CONFIG_NETFILTER_XT_MATCH_ESP is not set
+# CONFIG_NETFILTER_XT_MATCH_IPRANGE is not set
+# CONFIG_NETFILTER_XT_MATCH_LENGTH is not set
+# CONFIG_NETFILTER_XT_MATCH_LIMIT is not set
+# CONFIG_NETFILTER_XT_MATCH_MAC is not set
+# CONFIG_NETFILTER_XT_MATCH_MARK is not set
+# CONFIG_NETFILTER_XT_MATCH_OWNER is not set
+# CONFIG_NETFILTER_XT_MATCH_POLICY is not set
+# CONFIG_NETFILTER_XT_MATCH_MULTIPORT is not set
+# CONFIG_NETFILTER_XT_MATCH_PHYSDEV is not set
+# CONFIG_NETFILTER_XT_MATCH_PKTTYPE is not set
+# CONFIG_NETFILTER_XT_MATCH_QUOTA is not set
+# CONFIG_NETFILTER_XT_MATCH_RATEEST is not set
+# CONFIG_NETFILTER_XT_MATCH_REALM is not set
+# CONFIG_NETFILTER_XT_MATCH_SCTP is not set
+# CONFIG_NETFILTER_XT_MATCH_STATISTIC is not set
+# CONFIG_NETFILTER_XT_MATCH_STRING is not set
+# CONFIG_NETFILTER_XT_MATCH_TCPMSS is not set
+# CONFIG_NETFILTER_XT_MATCH_TIME is not set
+# CONFIG_NETFILTER_XT_MATCH_U32 is not set
+# CONFIG_NETFILTER_XT_MATCH_HASHLIMIT is not set
+
+#
+# IP: Netfilter Configuration
+#
+CONFIG_IP_NF_QUEUE=m
+CONFIG_IP_NF_IPTABLES=m
+CONFIG_IP_NF_MATCH_RECENT=m
+CONFIG_IP_NF_MATCH_ECN=m
+# CONFIG_IP_NF_MATCH_AH is not set
+CONFIG_IP_NF_MATCH_TTL=m
+CONFIG_IP_NF_MATCH_ADDRTYPE=m
+CONFIG_IP_NF_FILTER=m
+CONFIG_IP_NF_TARGET_REJECT=m
+CONFIG_IP_NF_TARGET_LOG=m
+CONFIG_IP_NF_TARGET_ULOG=m
+CONFIG_IP_NF_MANGLE=m
+CONFIG_IP_NF_TARGET_ECN=m
+# CONFIG_IP_NF_TARGET_TTL is not set
+CONFIG_IP_NF_RAW=m
+CONFIG_IP_NF_ARPTABLES=m
+CONFIG_IP_NF_ARPFILTER=m
+CONFIG_IP_NF_ARP_MANGLE=m
+
+#
+# IPv6: Netfilter Configuration
+#
+CONFIG_IP6_NF_QUEUE=m
+CONFIG_IP6_NF_IPTABLES=m
+CONFIG_IP6_NF_MATCH_RT=m
+CONFIG_IP6_NF_MATCH_OPTS=m
+CONFIG_IP6_NF_MATCH_FRAG=m
+CONFIG_IP6_NF_MATCH_HL=m
+CONFIG_IP6_NF_MATCH_IPV6HEADER=m
+# CONFIG_IP6_NF_MATCH_AH is not set
+# CONFIG_IP6_NF_MATCH_MH is not set
+CONFIG_IP6_NF_MATCH_EUI64=m
+CONFIG_IP6_NF_FILTER=m
+CONFIG_IP6_NF_TARGET_LOG=m
+# CONFIG_IP6_NF_TARGET_REJECT is not set
+CONFIG_IP6_NF_MANGLE=m
+# CONFIG_IP6_NF_TARGET_HL is not set
+CONFIG_IP6_NF_RAW=m
+
+#
+# Bridge: Netfilter Configuration
+#
+# CONFIG_BRIDGE_NF_EBTABLES is not set
+# CONFIG_IP_DCCP is not set
+CONFIG_IP_SCTP=m
+# CONFIG_SCTP_DBG_MSG is not set
+# CONFIG_SCTP_DBG_OBJCNT is not set
+# CONFIG_SCTP_HMAC_NONE is not set
+# CONFIG_SCTP_HMAC_SHA1 is not set
+CONFIG_SCTP_HMAC_MD5=y
+CONFIG_TIPC=m
+# CONFIG_TIPC_ADVANCED is not set
+# CONFIG_TIPC_DEBUG is not set
+CONFIG_ATM=m
+CONFIG_ATM_CLIP=m
+# CONFIG_ATM_CLIP_NO_ICMP is not set
+CONFIG_ATM_LANE=m
+CONFIG_ATM_MPOA=m
+CONFIG_ATM_BR2684=m
+# CONFIG_ATM_BR2684_IPFILTER is not set
+CONFIG_BRIDGE=m
+CONFIG_VLAN_8021Q=m
+# CONFIG_DECNET is not set
+CONFIG_LLC=m
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+CONFIG_WAN_ROUTER=m
+CONFIG_NET_SCHED=y
+
+#
+# Queueing/Scheduling
+#
+CONFIG_NET_SCH_CBQ=m
+CONFIG_NET_SCH_HTB=m
+CONFIG_NET_SCH_HFSC=m
+CONFIG_NET_SCH_ATM=m
+CONFIG_NET_SCH_PRIO=m
+# CONFIG_NET_SCH_RR is not set
+CONFIG_NET_SCH_RED=m
+CONFIG_NET_SCH_SFQ=m
+CONFIG_NET_SCH_TEQL=m
+CONFIG_NET_SCH_TBF=m
+CONFIG_NET_SCH_GRED=m
+CONFIG_NET_SCH_DSMARK=m
+CONFIG_NET_SCH_NETEM=m
+
+#
+# Classification
+#
+CONFIG_NET_CLS=y
+# CONFIG_NET_CLS_BASIC is not set
+CONFIG_NET_CLS_TCINDEX=m
+CONFIG_NET_CLS_ROUTE4=m
+CONFIG_NET_CLS_ROUTE=y
+CONFIG_NET_CLS_FW=m
+CONFIG_NET_CLS_U32=m
+# CONFIG_CLS_U32_PERF is not set
+# CONFIG_CLS_U32_MARK is not set
+CONFIG_NET_CLS_RSVP=m
+CONFIG_NET_CLS_RSVP6=m
+# CONFIG_NET_CLS_FLOW is not set
+# CONFIG_NET_EMATCH is not set
+# CONFIG_NET_CLS_ACT is not set
+# CONFIG_NET_CLS_IND is not set
+CONFIG_NET_SCH_FIFO=y
+
+#
+# Network testing
+#
+CONFIG_NET_PKTGEN=m
+# CONFIG_HAMRADIO is not set
+# CONFIG_CAN is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+CONFIG_FIB_RULES=y
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_MAC80211 is not set
+# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+# CONFIG_FW_LOADER is not set
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
+# CONFIG_SYS_HYPERVISOR is not set
+# CONFIG_CONNECTOR is not set
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+CONFIG_MTD_CONCAT=y
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_REDBOOT_PARTS is not set
+# CONFIG_MTD_CMDLINE_PARTS is not set
+# CONFIG_MTD_OF_PARTS is not set
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
+# CONFIG_MTD_OOPS is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+CONFIG_MTD_CFI=y
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_GEN_PROBE=y
+CONFIG_MTD_CFI_ADV_OPTIONS=y
+# CONFIG_MTD_CFI_NOSWAP is not set
+# CONFIG_MTD_CFI_BE_BYTE_SWAP is not set
+CONFIG_MTD_CFI_LE_BYTE_SWAP=y
+# CONFIG_MTD_CFI_GEOMETRY is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+# CONFIG_MTD_OTP is not set
+CONFIG_MTD_CFI_INTELEXT=y
+# CONFIG_MTD_CFI_AMDSTD is not set
+# CONFIG_MTD_CFI_STAA is not set
+CONFIG_MTD_CFI_UTIL=y
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+# CONFIG_MTD_PHYSMAP is not set
+CONFIG_MTD_PHYSMAP_OF=y
+# CONFIG_MTD_INTEL_VR_NOR is not set
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_PMC551 is not set
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+# CONFIG_MTD_NAND is not set
+# CONFIG_MTD_ONENAND is not set
+
+#
+# UBI - Unsorted block images
+#
+# CONFIG_MTD_UBI is not set
+CONFIG_OF_DEVICE=y
+# CONFIG_PARPORT is not set
+CONFIG_BLK_DEV=y
+# CONFIG_BLK_DEV_FD is not set
+# CONFIG_BLK_CPQ_DA is not set
+# CONFIG_BLK_CPQ_CISS_DA is not set
+# CONFIG_BLK_DEV_DAC960 is not set
+# CONFIG_BLK_DEV_UMEM is not set
+# CONFIG_BLK_DEV_COW_COMMON is not set
+CONFIG_BLK_DEV_LOOP=m
+CONFIG_BLK_DEV_CRYPTOLOOP=m
+CONFIG_BLK_DEV_NBD=m
+# CONFIG_BLK_DEV_SX8 is not set
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_BLK_DEV_RAM_SIZE=4096
+# CONFIG_BLK_DEV_XIP is not set
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_ATA_OVER_ETH is not set
+CONFIG_MISC_DEVICES=y
+# CONFIG_PHANTOM is not set
+# CONFIG_EEPROM_93CX6 is not set
+# CONFIG_SGI_IOC4 is not set
+# CONFIG_TIFM_CORE is not set
+# CONFIG_ENCLOSURE_SERVICES is not set
+CONFIG_HAVE_IDE=y
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+# CONFIG_SCSI is not set
+# CONFIG_SCSI_DMA is not set
+# CONFIG_SCSI_NETLINK is not set
+# CONFIG_ATA is not set
+CONFIG_MD=y
+CONFIG_BLK_DEV_MD=y
+CONFIG_MD_LINEAR=y
+CONFIG_MD_RAID0=y
+CONFIG_MD_RAID1=y
+CONFIG_MD_RAID10=y
+# CONFIG_MD_RAID456 is not set
+CONFIG_MD_MULTIPATH=y
+CONFIG_MD_FAULTY=y
+CONFIG_BLK_DEV_DM=y
+# CONFIG_DM_DEBUG is not set
+CONFIG_DM_CRYPT=y
+CONFIG_DM_SNAPSHOT=y
+CONFIG_DM_MIRROR=y
+CONFIG_DM_ZERO=y
+# CONFIG_DM_MULTIPATH is not set
+# CONFIG_DM_DELAY is not set
+# CONFIG_DM_UEVENT is not set
+# CONFIG_FUSION is not set
+
+#
+# IEEE 1394 (FireWire) support
+#
+# CONFIG_FIREWIRE is not set
+# CONFIG_IEEE1394 is not set
+# CONFIG_I2O is not set
+# CONFIG_MACINTOSH_DRIVERS is not set
+CONFIG_NETDEVICES=y
+# CONFIG_NETDEVICES_MULTIQUEUE is not set
+CONFIG_DUMMY=m
+CONFIG_BONDING=m
+# CONFIG_MACVLAN is not set
+# CONFIG_EQUALIZER is not set
+CONFIG_TUN=m
+# CONFIG_VETH is not set
+# CONFIG_ARCNET is not set
+CONFIG_PHYLIB=y
+
+#
+# MII PHY device drivers
+#
+# CONFIG_MARVELL_PHY is not set
+# CONFIG_DAVICOM_PHY is not set
+# CONFIG_QSEMI_PHY is not set
+# CONFIG_LXT_PHY is not set
+# CONFIG_CICADA_PHY is not set
+# CONFIG_VITESSE_PHY is not set
+# CONFIG_SMSC_PHY is not set
+CONFIG_BROADCOM_PHY=y
+# CONFIG_ICPLUS_PHY is not set
+# CONFIG_REALTEK_PHY is not set
+# CONFIG_FIXED_PHY is not set
+# CONFIG_MDIO_BITBANG is not set
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+# CONFIG_HAPPYMEAL is not set
+# CONFIG_SUNGEM is not set
+# CONFIG_CASSINI is not set
+# CONFIG_NET_VENDOR_3COM is not set
+# CONFIG_NET_TULIP is not set
+# CONFIG_HP100 is not set
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_NET_PCI is not set
+# CONFIG_B44 is not set
+CONFIG_NETDEV_1000=y
+# CONFIG_ACENIC is not set
+# CONFIG_DL2K is not set
+# CONFIG_E1000 is not set
+# CONFIG_E1000E is not set
+# CONFIG_E1000E_ENABLED is not set
+# CONFIG_IP1000 is not set
+# CONFIG_IGB is not set
+# CONFIG_NS83820 is not set
+# CONFIG_HAMACHI is not set
+# CONFIG_YELLOWFIN is not set
+# CONFIG_R8169 is not set
+# CONFIG_SIS190 is not set
+# CONFIG_SKGE is not set
+# CONFIG_SKY2 is not set
+# CONFIG_SK98LIN is not set
+# CONFIG_VIA_VELOCITY is not set
+# CONFIG_TIGON3 is not set
+# CONFIG_BNX2 is not set
+CONFIG_GIANFAR=y
+# CONFIG_GFAR_NAPI is not set
+# CONFIG_QLA3XXX is not set
+# CONFIG_ATL1 is not set
+# CONFIG_NETDEV_10000 is not set
+# CONFIG_TR is not set
+
+#
+# Wireless LAN
+#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
+# CONFIG_WAN is not set
+CONFIG_ATM_DRIVERS=y
+# CONFIG_ATM_DUMMY is not set
+# CONFIG_ATM_TCP is not set
+# CONFIG_ATM_LANAI is not set
+# CONFIG_ATM_ENI is not set
+# CONFIG_ATM_FIRESTREAM is not set
+# CONFIG_ATM_ZATM is not set
+# CONFIG_ATM_NICSTAR is not set
+# CONFIG_ATM_IDT77252 is not set
+# CONFIG_ATM_AMBASSADOR is not set
+# CONFIG_ATM_HORIZON is not set
+# CONFIG_ATM_IA is not set
+# CONFIG_ATM_FORE200E_MAYBE is not set
+# CONFIG_ATM_HE is not set
+# CONFIG_FDDI is not set
+# CONFIG_HIPPI is not set
+CONFIG_PPP=m
+CONFIG_PPP_MULTILINK=y
+CONFIG_PPP_FILTER=y
+CONFIG_PPP_ASYNC=m
+CONFIG_PPP_SYNC_TTY=m
+CONFIG_PPP_DEFLATE=m
+CONFIG_PPP_BSDCOMP=m
+# CONFIG_PPP_MPPE is not set
+CONFIG_PPPOE=m
+CONFIG_PPPOATM=m
+# CONFIG_PPPOL2TP is not set
+CONFIG_SLIP=m
+CONFIG_SLIP_COMPRESSED=y
+CONFIG_SLHC=m
+CONFIG_SLIP_SMART=y
+CONFIG_SLIP_MODE_SLIP6=y
+CONFIG_NETCONSOLE=y
+# CONFIG_NETCONSOLE_DYNAMIC is not set
+CONFIG_NETPOLL=y
+CONFIG_NETPOLL_TRAP=y
+CONFIG_NET_POLL_CONTROLLER=y
+# CONFIG_ISDN is not set
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
+
+#
+# Userland interfaces
+#
+CONFIG_INPUT_MOUSEDEV=y
+CONFIG_INPUT_MOUSEDEV_PSAUX=y
+CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
+CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
+# CONFIG_INPUT_JOYDEV is not set
+# CONFIG_INPUT_EVDEV is not set
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input Device Drivers
+#
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
+# CONFIG_INPUT_TOUCHSCREEN is not set
+# CONFIG_INPUT_MISC is not set
+
+#
+# Hardware I/O ports
+#
+# CONFIG_SERIO is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+CONFIG_VT=y
+CONFIG_VT_CONSOLE=y
+CONFIG_HW_CONSOLE=y
+# CONFIG_VT_HW_CONSOLE_BINDING is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+# CONFIG_NOZOMI is not set
+
+#
+# Serial drivers
+#
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+# CONFIG_SERIAL_8250_PCI is not set
+CONFIG_SERIAL_8250_NR_UARTS=2
+CONFIG_SERIAL_8250_RUNTIME_UARTS=2
+# CONFIG_SERIAL_8250_EXTENDED is not set
+
+#
+# Non-8250 serial port support
+#
+# CONFIG_SERIAL_UARTLITE is not set
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+# CONFIG_SERIAL_JSM is not set
+# CONFIG_SERIAL_OF_PLATFORM is not set
+CONFIG_UNIX98_PTYS=y
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=256
+# CONFIG_IPMI_HANDLER is not set
+CONFIG_HW_RANDOM=m
+# CONFIG_NVRAM is not set
+# CONFIG_GEN_RTC is not set
+# CONFIG_R3964 is not set
+# CONFIG_APPLICOM is not set
+# CONFIG_RAW_DRIVER is not set
+# CONFIG_TCG_TPM is not set
+CONFIG_DEVPORT=y
+CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_CHARDEV=y
+
+#
+# I2C Algorithms
+#
+# CONFIG_I2C_ALGOBIT is not set
+# CONFIG_I2C_ALGOPCF is not set
+# CONFIG_I2C_ALGOPCA is not set
+
+#
+# I2C Hardware Bus support
+#
+# CONFIG_I2C_ALI1535 is not set
+# CONFIG_I2C_ALI1563 is not set
+# CONFIG_I2C_ALI15X3 is not set
+# CONFIG_I2C_AMD756 is not set
+# CONFIG_I2C_AMD8111 is not set
+# CONFIG_I2C_I801 is not set
+# CONFIG_I2C_I810 is not set
+# CONFIG_I2C_PIIX4 is not set
+CONFIG_I2C_MPC=y
+# CONFIG_I2C_NFORCE2 is not set
+# CONFIG_I2C_OCORES is not set
+# CONFIG_I2C_PARPORT_LIGHT is not set
+# CONFIG_I2C_PROSAVAGE is not set
+# CONFIG_I2C_SAVAGE4 is not set
+# CONFIG_I2C_SIMTEC is not set
+# CONFIG_I2C_SIS5595 is not set
+# CONFIG_I2C_SIS630 is not set
+# CONFIG_I2C_SIS96X is not set
+# CONFIG_I2C_TAOS_EVM is not set
+# CONFIG_I2C_STUB is not set
+# CONFIG_I2C_VIA is not set
+# CONFIG_I2C_VIAPRO is not set
+# CONFIG_I2C_VOODOO3 is not set
+
+#
+# Miscellaneous I2C Chip support
+#
+# CONFIG_DS1682 is not set
+# CONFIG_SENSORS_EEPROM is not set
+# CONFIG_SENSORS_PCF8574 is not set
+# CONFIG_PCF8575 is not set
+# CONFIG_SENSORS_PCF8591 is not set
+# CONFIG_TPS65010 is not set
+# CONFIG_SENSORS_MAX6875 is not set
+# CONFIG_SENSORS_TSL2550 is not set
+# CONFIG_I2C_DEBUG_CORE is not set
+# CONFIG_I2C_DEBUG_ALGO is not set
+# CONFIG_I2C_DEBUG_BUS is not set
+# CONFIG_I2C_DEBUG_CHIP is not set
+
+#
+# SPI support
+#
+# CONFIG_SPI is not set
+# CONFIG_SPI_MASTER is not set
+# CONFIG_W1 is not set
+# CONFIG_POWER_SUPPLY is not set
+CONFIG_HWMON=y
+# CONFIG_HWMON_VID is not set
+# CONFIG_SENSORS_AD7418 is not set
+# CONFIG_SENSORS_ADM1021 is not set
+# CONFIG_SENSORS_ADM1025 is not set
+# CONFIG_SENSORS_ADM1026 is not set
+# CONFIG_SENSORS_ADM1029 is not set
+# CONFIG_SENSORS_ADM1031 is not set
+# CONFIG_SENSORS_ADM9240 is not set
+# CONFIG_SENSORS_ADT7470 is not set
+# CONFIG_SENSORS_ADT7473 is not set
+# CONFIG_SENSORS_ATXP1 is not set
+# CONFIG_SENSORS_DS1621 is not set
+# CONFIG_SENSORS_I5K_AMB is not set
+# CONFIG_SENSORS_F71805F is not set
+# CONFIG_SENSORS_F71882FG is not set
+# CONFIG_SENSORS_F75375S is not set
+# CONFIG_SENSORS_GL518SM is not set
+# CONFIG_SENSORS_GL520SM is not set
+# CONFIG_SENSORS_IT87 is not set
+# CONFIG_SENSORS_LM63 is not set
+# CONFIG_SENSORS_LM75 is not set
+# CONFIG_SENSORS_LM77 is not set
+# CONFIG_SENSORS_LM78 is not set
+# CONFIG_SENSORS_LM80 is not set
+# CONFIG_SENSORS_LM83 is not set
+# CONFIG_SENSORS_LM85 is not set
+# CONFIG_SENSORS_LM87 is not set
+# CONFIG_SENSORS_LM90 is not set
+# CONFIG_SENSORS_LM92 is not set
+# CONFIG_SENSORS_LM93 is not set
+# CONFIG_SENSORS_MAX1619 is not set
+# CONFIG_SENSORS_MAX6650 is not set
+# CONFIG_SENSORS_PC87360 is not set
+# CONFIG_SENSORS_PC87427 is not set
+# CONFIG_SENSORS_SIS5595 is not set
+# CONFIG_SENSORS_DME1737 is not set
+# CONFIG_SENSORS_SMSC47M1 is not set
+# CONFIG_SENSORS_SMSC47M192 is not set
+# CONFIG_SENSORS_SMSC47B397 is not set
+# CONFIG_SENSORS_ADS7828 is not set
+# CONFIG_SENSORS_THMC50 is not set
+# CONFIG_SENSORS_VIA686A is not set
+# CONFIG_SENSORS_VT1211 is not set
+# CONFIG_SENSORS_VT8231 is not set
+# CONFIG_SENSORS_W83781D is not set
+# CONFIG_SENSORS_W83791D is not set
+# CONFIG_SENSORS_W83792D is not set
+# CONFIG_SENSORS_W83793 is not set
+# CONFIG_SENSORS_W83L785TS is not set
+# CONFIG_SENSORS_W83L786NG is not set
+# CONFIG_SENSORS_W83627HF is not set
+# CONFIG_SENSORS_W83627EHF is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+# CONFIG_THERMAL is not set
+CONFIG_WATCHDOG=y
+# CONFIG_WATCHDOG_NOWAYOUT is not set
+
+#
+# Watchdog Device Drivers
+#
+CONFIG_SOFT_WATCHDOG=m
+
+#
+# PCI-based Watchdog Cards
+#
+# CONFIG_PCIPCWATCHDOG is not set
+# CONFIG_WDTPCI is not set
+
+#
+# Sonics Silicon Backplane
+#
+CONFIG_SSB_POSSIBLE=y
+# CONFIG_SSB is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_SM501 is not set
+
+#
+# Multimedia devices
+#
+# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+CONFIG_DAB=y
+
+#
+# Graphics support
+#
+# CONFIG_AGP is not set
+# CONFIG_DRM is not set
+# CONFIG_VGASTATE is not set
+CONFIG_VIDEO_OUTPUT_CONTROL=m
+# CONFIG_FB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
+
+#
+# Console display driver support
+#
+CONFIG_VGA_CONSOLE=y
+# CONFIG_VGACON_SOFT_SCROLLBACK is not set
+CONFIG_DUMMY_CONSOLE=y
+
+#
+# Sound
+#
+# CONFIG_SOUND is not set
+CONFIG_HID_SUPPORT=y
+CONFIG_HID=y
+# CONFIG_HID_DEBUG is not set
+# CONFIG_HIDRAW is not set
+CONFIG_USB_SUPPORT=y
+CONFIG_USB_ARCH_HAS_HCD=y
+CONFIG_USB_ARCH_HAS_OHCI=y
+CONFIG_USB_ARCH_HAS_EHCI=y
+# CONFIG_USB is not set
+
+#
+# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
+#
+# CONFIG_USB_GADGET is not set
+# CONFIG_MMC is not set
+# CONFIG_MEMSTICK is not set
+# CONFIG_NEW_LEDS is not set
+# CONFIG_INFINIBAND is not set
+# CONFIG_EDAC is not set
+# CONFIG_RTC_CLASS is not set
+# CONFIG_DMADEVICES is not set
+
+#
+# Userspace I/O
+#
+# CONFIG_UIO is not set
+
+#
+# File systems
+#
+CONFIG_EXT2_FS=y
+CONFIG_EXT2_FS_XATTR=y
+CONFIG_EXT2_FS_POSIX_ACL=y
+# CONFIG_EXT2_FS_SECURITY is not set
+# CONFIG_EXT2_FS_XIP is not set
+CONFIG_EXT3_FS=y
+CONFIG_EXT3_FS_XATTR=y
+CONFIG_EXT3_FS_POSIX_ACL=y
+# CONFIG_EXT3_FS_SECURITY is not set
+# CONFIG_EXT4DEV_FS is not set
+CONFIG_JBD=y
+# CONFIG_JBD_DEBUG is not set
+CONFIG_FS_MBCACHE=y
+CONFIG_REISERFS_FS=m
+# CONFIG_REISERFS_CHECK is not set
+# CONFIG_REISERFS_PROC_INFO is not set
+CONFIG_REISERFS_FS_XATTR=y
+CONFIG_REISERFS_FS_POSIX_ACL=y
+# CONFIG_REISERFS_FS_SECURITY is not set
+# CONFIG_JFS_FS is not set
+CONFIG_FS_POSIX_ACL=y
+# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
+CONFIG_OCFS2_FS=m
+CONFIG_OCFS2_DEBUG_MASKLOG=y
+# CONFIG_OCFS2_DEBUG_FS is not set
+CONFIG_DNOTIFY=y
+CONFIG_INOTIFY=y
+CONFIG_INOTIFY_USER=y
+# CONFIG_QUOTA is not set
+CONFIG_AUTOFS_FS=m
+CONFIG_AUTOFS4_FS=m
+# CONFIG_FUSE_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+# CONFIG_MSDOS_FS is not set
+# CONFIG_VFAT_FS is not set
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_KCORE=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
+# CONFIG_HUGETLB_PAGE is not set
+CONFIG_CONFIGFS_FS=m
+
+#
+# Miscellaneous filesystems
+#
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+# CONFIG_JFFS2_FS is not set
+# CONFIG_CRAMFS is not set
+# CONFIG_VXFS_FS is not set
+CONFIG_MINIX_FS=m
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+CONFIG_ROMFS_FS=m
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+CONFIG_NETWORK_FILESYSTEMS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
+CONFIG_NFS_V4=y
+CONFIG_NFS_DIRECTIO=y
+# CONFIG_NFSD is not set
+CONFIG_ROOT_NFS=y
+CONFIG_LOCKD=y
+CONFIG_LOCKD_V4=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+CONFIG_SUNRPC_GSS=y
+# CONFIG_SUNRPC_BIND34 is not set
+CONFIG_RPCSEC_GSS_KRB5=y
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+CONFIG_SMB_FS=m
+CONFIG_SMB_NLS_DEFAULT=y
+CONFIG_SMB_NLS_REMOTE="cp437"
+CONFIG_CIFS=m
+# CONFIG_CIFS_STATS is not set
+# CONFIG_CIFS_WEAK_PW_HASH is not set
+CONFIG_CIFS_XATTR=y
+CONFIG_CIFS_POSIX=y
+# CONFIG_CIFS_DEBUG2 is not set
+# CONFIG_CIFS_EXPERIMENTAL is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+
+#
+# Partition Types
+#
+# CONFIG_PARTITION_ADVANCED is not set
+CONFIG_MSDOS_PARTITION=y
+CONFIG_NLS=m
+CONFIG_NLS_DEFAULT="iso8859-1"
+CONFIG_NLS_CODEPAGE_437=m
+CONFIG_NLS_CODEPAGE_737=m
+CONFIG_NLS_CODEPAGE_775=m
+CONFIG_NLS_CODEPAGE_850=m
+CONFIG_NLS_CODEPAGE_852=m
+CONFIG_NLS_CODEPAGE_855=m
+CONFIG_NLS_CODEPAGE_857=m
+CONFIG_NLS_CODEPAGE_860=m
+CONFIG_NLS_CODEPAGE_861=m
+CONFIG_NLS_CODEPAGE_862=m
+CONFIG_NLS_CODEPAGE_863=m
+CONFIG_NLS_CODEPAGE_864=m
+CONFIG_NLS_CODEPAGE_865=m
+CONFIG_NLS_CODEPAGE_866=m
+CONFIG_NLS_CODEPAGE_869=m
+CONFIG_NLS_CODEPAGE_936=m
+CONFIG_NLS_CODEPAGE_950=m
+CONFIG_NLS_CODEPAGE_932=m
+CONFIG_NLS_CODEPAGE_949=m
+CONFIG_NLS_CODEPAGE_874=m
+CONFIG_NLS_ISO8859_8=m
+CONFIG_NLS_CODEPAGE_1250=m
+CONFIG_NLS_CODEPAGE_1251=m
+CONFIG_NLS_ASCII=m
+CONFIG_NLS_ISO8859_1=m
+CONFIG_NLS_ISO8859_2=m
+CONFIG_NLS_ISO8859_3=m
+CONFIG_NLS_ISO8859_4=m
+CONFIG_NLS_ISO8859_5=m
+CONFIG_NLS_ISO8859_6=m
+CONFIG_NLS_ISO8859_7=m
+CONFIG_NLS_ISO8859_9=m
+CONFIG_NLS_ISO8859_13=m
+CONFIG_NLS_ISO8859_14=m
+CONFIG_NLS_ISO8859_15=m
+CONFIG_NLS_KOI8_R=m
+CONFIG_NLS_KOI8_U=m
+CONFIG_NLS_UTF8=m
+# CONFIG_DLM is not set
+
+#
+# Library routines
+#
+CONFIG_BITREVERSE=y
+CONFIG_CRC_CCITT=m
+# CONFIG_CRC16 is not set
+# CONFIG_CRC_ITU_T is not set
+CONFIG_CRC32=y
+# CONFIG_CRC7 is not set
+CONFIG_LIBCRC32C=m
+CONFIG_ZLIB_INFLATE=m
+CONFIG_ZLIB_DEFLATE=m
+CONFIG_PLIST=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_WARN_DEPRECATED=y
+CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_UNUSED_SYMBOLS is not set
+CONFIG_DEBUG_FS=y
+# CONFIG_HEADERS_CHECK is not set
+CONFIG_DEBUG_KERNEL=y
+# CONFIG_DEBUG_SHIRQ is not set
+CONFIG_DETECT_SOFTLOCKUP=y
+CONFIG_SCHED_DEBUG=y
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
+# CONFIG_DEBUG_SLAB is not set
+# CONFIG_DEBUG_RT_MUTEXES is not set
+# CONFIG_RT_MUTEX_TESTER is not set
+# CONFIG_DEBUG_SPINLOCK is not set
+# CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+# CONFIG_DEBUG_KOBJECT is not set
+# CONFIG_DEBUG_BUGVERBOSE is not set
+CONFIG_DEBUG_INFO=y
+# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_LIST is not set
+# CONFIG_DEBUG_SG is not set
+# CONFIG_BOOT_PRINTK_DELAY is not set
+# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_BACKTRACE_SELF_TEST is not set
+# CONFIG_FAULT_INJECTION is not set
+# CONFIG_SAMPLES is not set
+# CONFIG_DEBUG_STACKOVERFLOW is not set
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_PAGEALLOC is not set
+CONFIG_DEBUGGER=y
+# CONFIG_XMON is not set
+# CONFIG_VIRQ_DEBUG is not set
+# CONFIG_BDI_SWITCH is not set
+# CONFIG_PPC_EARLY_DEBUG is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+CONFIG_SECURITY=y
+CONFIG_SECURITY_NETWORK=y
+# CONFIG_SECURITY_NETWORK_XFRM is not set
+CONFIG_SECURITY_CAPABILITIES=y
+# CONFIG_SECURITY_FILE_CAPABILITIES is not set
+CONFIG_SECURITY_DEFAULT_MMAP_MIN_ADDR=0
+CONFIG_CRYPTO=y
+CONFIG_CRYPTO_ALGAPI=y
+CONFIG_CRYPTO_AEAD=m
+CONFIG_CRYPTO_BLKCIPHER=y
+# CONFIG_CRYPTO_SEQIV is not set
+CONFIG_CRYPTO_HASH=y
+CONFIG_CRYPTO_MANAGER=y
+CONFIG_CRYPTO_HMAC=y
+# CONFIG_CRYPTO_XCBC is not set
+CONFIG_CRYPTO_NULL=m
+CONFIG_CRYPTO_MD4=m
+CONFIG_CRYPTO_MD5=y
+CONFIG_CRYPTO_SHA1=m
+CONFIG_CRYPTO_SHA256=m
+CONFIG_CRYPTO_SHA512=m
+CONFIG_CRYPTO_WP512=m
+# CONFIG_CRYPTO_TGR192 is not set
+# CONFIG_CRYPTO_GF128MUL is not set
+CONFIG_CRYPTO_ECB=m
+CONFIG_CRYPTO_CBC=y
+CONFIG_CRYPTO_PCBC=m
+# CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_XTS is not set
+# CONFIG_CRYPTO_CTR is not set
+# CONFIG_CRYPTO_GCM is not set
+# CONFIG_CRYPTO_CCM is not set
+# CONFIG_CRYPTO_CRYPTD is not set
+CONFIG_CRYPTO_DES=y
+# CONFIG_CRYPTO_FCRYPT is not set
+CONFIG_CRYPTO_BLOWFISH=m
+CONFIG_CRYPTO_TWOFISH=m
+CONFIG_CRYPTO_TWOFISH_COMMON=m
+CONFIG_CRYPTO_SERPENT=m
+CONFIG_CRYPTO_AES=m
+CONFIG_CRYPTO_CAST5=m
+CONFIG_CRYPTO_CAST6=m
+CONFIG_CRYPTO_TEA=m
+CONFIG_CRYPTO_ARC4=m
+CONFIG_CRYPTO_KHAZAD=m
+CONFIG_CRYPTO_ANUBIS=m
+# CONFIG_CRYPTO_SEED is not set
+# CONFIG_CRYPTO_SALSA20 is not set
+CONFIG_CRYPTO_DEFLATE=m
+CONFIG_CRYPTO_MICHAEL_MIC=m
+CONFIG_CRYPTO_CRC32C=m
+# CONFIG_CRYPTO_CAMELLIA is not set
+CONFIG_CRYPTO_TEST=m
+CONFIG_CRYPTO_AUTHENC=m
+# CONFIG_CRYPTO_LZO is not set
+CONFIG_CRYPTO_HW=y
+# CONFIG_CRYPTO_DEV_HIFN_795X is not set
+# CONFIG_PPC_CLOCK is not set
stw r11,PT_REGS(r12)
#if defined(CONFIG_40x) || defined(CONFIG_BOOKE)
/* Check to see if the dbcr0 register is set up to debug. Use the
- single-step bit to do this. */
+ internal debug mode bit to do this. */
lwz r12,THREAD_DBCR0(r12)
- andis. r12,r12,DBCR0_IC@h
+ andis. r12,r12,DBCR0_IDM@h
beq+ 3f
/* From user and task is ptraced - load up global dbcr0 */
li r12,-1 /* clear all pending debug events */
lis r11,global_dbcr0@ha
tophys(r11,r11)
addi r11,r11,global_dbcr0@l
+#ifdef CONFIG_SMP
+ rlwinm r9,r1,0,0,(31-THREAD_SHIFT)
+ lwz r9,TI_CPU(r9)
+ slwi r9,r9,3
+ add r11,r11,r9
+#endif
lwz r12,0(r11)
mtspr SPRN_DBCR0,r12
lwz r12,4(r11)
stw r11,_CCR(r1)
syscall_exit_cont:
#if defined(CONFIG_4xx) || defined(CONFIG_BOOKE)
- /* If the process has its own DBCR0 value, load it up. The single
- step bit tells us that dbcr0 should be loaded. */
+ /* If the process has its own DBCR0 value, load it up. The internal
+ debug mode bit tells us that dbcr0 should be loaded. */
lwz r0,THREAD+THREAD_DBCR0(r2)
- andis. r10,r0,DBCR0_IC@h
+ andis. r10,r0,DBCR0_IDM@h
bnel- load_dbcr0
#endif
#ifdef CONFIG_44x
restore_user:
#if defined(CONFIG_4xx) || defined(CONFIG_BOOKE)
- /* Check whether this process has its own DBCR0 value. The single
- step bit tells us that dbcr0 should be loaded. */
+ /* Check whether this process has its own DBCR0 value. The internal
+ debug mode bit tells us that dbcr0 should be loaded. */
lwz r0,THREAD+THREAD_DBCR0(r2)
- andis. r10,r0,DBCR0_IC@h
+ andis. r10,r0,DBCR0_IDM@h
bnel- load_dbcr0
#endif
mfspr r10,SPRN_DBCR0
lis r11,global_dbcr0@ha
addi r11,r11,global_dbcr0@l
+#ifdef CONFIG_SMP
+ rlwinm r9,r1,0,0,(31-THREAD_SHIFT)
+ lwz r9,TI_CPU(r9)
+ slwi r9,r9,3
+ add r11,r11,r9
+#endif
stw r10,0(r11)
mtspr SPRN_DBCR0,r0
lwz r10,4(r11)
.section .bss
.align 4
global_dbcr0:
- .space 8
+ .space 8*NR_CPUS
.previous
#endif /* !(CONFIG_4xx || CONFIG_BOOKE) */
SET_IVOR(12, WatchdogTimer);
SET_IVOR(13, DataTLBError);
SET_IVOR(14, InstructionTLBError);
- SET_IVOR(15, Debug);
+ SET_IVOR(15, DebugCrit);
/* Establish the interrupt vector base */
lis r4,interrupt_base@h /* IVPR only uses the high 16-bits */
b InstructionStorage
/* Debug Interrupt */
- DEBUG_EXCEPTION
+ DEBUG_CRIT_EXCEPTION
/*
* Local functions
* is necessary since the MMU is always on, for Book-E parts, and the stacks
* are offset from KERNELBASE.
*
+ * There is some space optimization to be had here if desired. However
+ * to allow for a common kernel with support for debug exceptions either
+ * going to critical or their own debug level we aren't currently
+ * providing configurations that micro-optimize space usage.
*/
-#define BOOKE_EXCEPTION_STACK_SIZE (8192)
+#ifdef CONFIG_44x
+#define NUM_EXCEPTION_LVLS 2
+#else
+#define NUM_EXCEPTION_LVLS 3
+#endif
+#define BOOKE_EXCEPTION_STACK_SIZE (4096 * NUM_EXCEPTION_LVLS)
/* CRIT_SPRG only used in critical exception handling */
#define CRIT_SPRG SPRN_SPRG2
#define CRIT_STACK_TOP (exception_stack_top)
/* only on e200 for now */
-#define DEBUG_STACK_TOP (exception_stack_top - 4096)
+#define DEBUG_STACK_TOP (exception_stack_top - 8192)
#define DEBUG_SPRG SPRN_SPRG6W
#ifdef CONFIG_SMP
* save (and later restore) the MSR via SPRN_CSRR1, which will still have
* the MSR_DE bit set.
*/
-#ifdef CONFIG_E200
-#define DEBUG_EXCEPTION \
- START_EXCEPTION(Debug); \
+#define DEBUG_DEBUG_EXCEPTION \
+ START_EXCEPTION(DebugDebug); \
DEBUG_EXCEPTION_PROLOG; \
\
/* \
cmplw r12,r10; \
blt+ 2f; /* addr below exception vectors */ \
\
- lis r10,Debug@h; \
- ori r10,r10,Debug@l; \
+ lis r10,DebugDebug@h; \
+ ori r10,r10,DebugDebug@l; \
cmplw r12,r10; \
bgt+ 2f; /* addr above exception vectors */ \
\
2: mfspr r4,SPRN_DBSR; \
addi r3,r1,STACK_FRAME_OVERHEAD; \
EXC_XFER_TEMPLATE(DebugException, 0x2002, (MSR_KERNEL & ~(MSR_ME|MSR_DE|MSR_CE)), NOCOPY, debug_transfer_to_handler, ret_from_debug_exc)
-#else
-#define DEBUG_EXCEPTION \
- START_EXCEPTION(Debug); \
+
+#define DEBUG_CRIT_EXCEPTION \
+ START_EXCEPTION(DebugCrit); \
CRITICAL_EXCEPTION_PROLOG; \
\
/* \
cmplw r12,r10; \
blt+ 2f; /* addr below exception vectors */ \
\
- lis r10,Debug@h; \
- ori r10,r10,Debug@l; \
+ lis r10,DebugCrit@h; \
+ ori r10,r10,DebugCrit@l; \
cmplw r12,r10; \
bgt+ 2f; /* addr above exception vectors */ \
\
2: mfspr r4,SPRN_DBSR; \
addi r3,r1,STACK_FRAME_OVERHEAD; \
EXC_XFER_TEMPLATE(DebugException, 0x2002, (MSR_KERNEL & ~(MSR_ME|MSR_DE|MSR_CE)), NOCOPY, crit_transfer_to_handler, ret_from_crit_exc)
-#endif
#define INSTRUCTION_STORAGE_EXCEPTION \
START_EXCEPTION(InstructionStorage) \
SET_IVOR(12, WatchdogTimer);
SET_IVOR(13, DataTLBError);
SET_IVOR(14, InstructionTLBError);
- SET_IVOR(15, Debug);
+ SET_IVOR(15, DebugDebug);
+#if defined(CONFIG_E500)
+ SET_IVOR(15, DebugCrit);
+#endif
SET_IVOR(32, SPEUnavailable);
SET_IVOR(33, SPEFloatingPointData);
SET_IVOR(34, SPEFloatingPointRound);
/* Debug Interrupt */
- DEBUG_EXCEPTION
+ DEBUG_DEBUG_EXCEPTION
+#if defined(CONFIG_E500)
+ DEBUG_CRIT_EXCEPTION
+#endif
/*
* Local functions
new_blocks = max_blocks - info->max_blocks;
- block = kmalloc(sizeof(rh_block_t) * max_blocks, GFP_KERNEL);
+ block = kmalloc(sizeof(rh_block_t) * max_blocks, GFP_ATOMIC);
if (block == NULL)
return -ENOMEM;
if ((alignment & (alignment - 1)) != 0)
return ERR_PTR(-EINVAL);
- info = kmalloc(sizeof(*info), GFP_KERNEL);
+ info = kmalloc(sizeof(*info), GFP_ATOMIC);
if (info == NULL)
return ERR_PTR(-ENOMEM);
select 8260
select FSL_SOC
select PQ2_ADS_PCI_PIC if PCI
- select PPC_CPM_NEW_BINDING
help
This option enables support for the MPC8272 ADS board
select 8260
select FSL_SOC
select PQ2_ADS_PCI_PIC if PCI
- select PPC_CPM_NEW_BINDING
help
This option enables support for the PQ2FADS board
select 8272
select 8260
select FSL_SOC
- select PPC_CPM_NEW_BINDING
select MDIO_BITBANG
help
This enables support for the Embedded Planet EP8248E board.
static struct of_device_id mpc837x_ids[] = {
{ .type = "soc", },
{ .compatible = "soc", },
+ { .compatible = "simple-bus", },
{},
};
#define MPC83XX_SCCR_USB_DRCM_10 0x00200000
#define MPC8315_SCCR_USB_MASK 0x00c00000
#define MPC8315_SCCR_USB_DRCM_11 0x00c00000
+#define MPC8315_SCCR_USB_DRCM_01 0x00400000
#define MPC837X_SCCR_USB_DRCM_11 0x00c00000
/* system i/o configuration register low */
/* USB Control Register */
#define FSL_USB2_CONTROL_OFFS 0x500
#define CONTROL_UTMI_PHY_EN 0x00000200
+#define CONTROL_REFSEL_24MHZ 0x00000040
#define CONTROL_REFSEL_48MHZ 0x00000080
#define CONTROL_PHY_CLK_SEL_ULPI 0x00000400
#define CONTROL_OTG_PORT 0x00000020
if (immr_node && of_device_is_compatible(immr_node, "fsl,mpc8315-immr"))
clrsetbits_be32(immap + MPC83XX_SCCR_OFFS,
MPC8315_SCCR_USB_MASK,
- MPC8315_SCCR_USB_DRCM_11);
+ MPC8315_SCCR_USB_DRCM_01);
else
clrsetbits_be32(immap + MPC83XX_SCCR_OFFS,
MPC83XX_SCCR_USB_MASK,
/* Using on-chip PHY */
if (prop && (!strcmp(prop, "utmi_wide") ||
!strcmp(prop, "utmi"))) {
- /* Set UTMI_PHY_EN, REFSEL to 48MHZ */
+ u32 refsel;
+
+ if (of_device_is_compatible(immr_node, "fsl,mpc8315-immr"))
+ refsel = CONTROL_REFSEL_24MHZ;
+ else
+ refsel = CONTROL_REFSEL_48MHZ;
+ /* Set UTMI_PHY_EN and REFSEL */
out_be32(usb_regs + FSL_USB2_CONTROL_OFFS,
- CONTROL_UTMI_PHY_EN | CONTROL_REFSEL_48MHZ);
+ CONTROL_UTMI_PHY_EN | refsel);
/* Using external UPLI PHY */
} else if (prop && !strcmp(prop, "ulpi")) {
/* Set PHY_CLK_SEL to ULPI */
config MPC8560_ADS
bool "Freescale MPC8560 ADS"
select DEFAULT_UIMAGE
- select PPC_CPM_NEW_BINDING
select CPM2
help
This option enables support for the MPC 8560 ADS board
config KSI8560
bool "Emerson KSI8560"
- select PPC_CPM_NEW_BINDING
select DEFAULT_UIMAGE
help
This option enables support for the Emerson KSI8560 board
board.
select CPM2
select DEFAULT_UIMAGE
- select PPC_CPM_NEW_BINDING
config TQM8540
bool "TQ Components TQM8540"
help
This option enables support for the TQ Components TQM8540 board.
select DEFAULT_UIMAGE
- select PPC_CPM_NEW_BINDING
select TQM85xx
config TQM8541
help
This option enables support for the TQ Components TQM8541 board.
select DEFAULT_UIMAGE
- select PPC_CPM_NEW_BINDING
select TQM85xx
select CPM2
help
This option enables support for the TQ Components TQM8555 board.
select DEFAULT_UIMAGE
- select PPC_CPM_NEW_BINDING
select TQM85xx
select CPM2
help
This option enables support for the TQ Components TQM8560 board.
select DEFAULT_UIMAGE
- select PPC_CPM_NEW_BINDING
select TQM85xx
select CPM2
config SBC8560
bool "Wind River SBC8560"
select DEFAULT_UIMAGE
- select PPC_CPM_NEW_BINDING if CPM2
help
This option enables support for the Wind River SBC8560 board
int i;
for (i = 0; i < ARRAY_SIZE(mpc8560_ads_pins); i++) {
- struct cpm_pin *pin = &mpc8560_ads_pins[i];
+ const struct cpm_pin *pin = &mpc8560_ads_pins[i];
cpm2_set_pin(pin->port, pin->pin, pin->flags);
}
#include <linux/delay.h>
#include <linux/seq_file.h>
#include <linux/interrupt.h>
+#include <linux/of_platform.h>
#include <asm/system.h>
#include <asm/time.h>
}
}
+static struct of_device_id mpc85xxds_ids[] = {
+ { .type = "soc", },
+ { .compatible = "soc", },
+ {},
+};
+
+static int __init mpc85xxds_publish_devices(void)
+{
+ return of_platform_bus_probe(NULL, mpc85xxds_ids, NULL);
+}
+machine_device_initcall(mpc8544_ds, mpc85xxds_publish_devices);
+
/*
* Called very early, device-tree isn't unflattened
*/
help
This option enables support for the MPC8641 HPCN board.
+config SBC8641D
+ bool "Wind River SBC8641D"
+ select DEFAULT_UIMAGE
+ help
+ This option enables support for the WRS SBC8641D board.
+
config MPC8610_HPCD
bool "Freescale MPC8610 HPCD"
select DEFAULT_UIMAGE
select FSL_PCI if PCI
select PPC_UDBG_16550
select MPIC
- default y if MPC8641_HPCN
+ default y if MPC8641_HPCN || SBC8641D
config MPC8610
bool
obj-$(CONFIG_SMP) += mpc86xx_smp.o
obj-$(CONFIG_MPC8641_HPCN) += mpc86xx_hpcn.o
+obj-$(CONFIG_SBC8641D) += sbc8641d.o
obj-$(CONFIG_MPC8610_HPCD) += mpc8610_hpcd.o
}
machine_device_initcall(mpc86xx_hpcd, mpc8610_declare_of_platform_devices);
-void __init
+static void __init
mpc86xx_hpcd_init_irq(void)
{
struct mpic *mpic1;
return 0;
}
-long __init
+static long __init
mpc86xx_time_init(void)
{
unsigned int temp;
}
#endif /* CONFIG_PCI */
-void __init
+static void __init
mpc86xx_hpcn_init_irq(void)
{
struct mpic *mpic1;
}
-void
+static void
mpc86xx_hpcn_show_cpuinfo(struct seq_file *m)
{
struct device_node *root;
{
unsigned long root = of_get_flat_dt_root();
- if (of_flat_dt_is_compatible(root, "mpc86xx"))
+ if (of_flat_dt_is_compatible(root, "fsl,mpc8641hpcn"))
return 1; /* Looks good */
+ /* Be nice and don't give silent boot death. Delete this in 2.6.27 */
+ if (of_flat_dt_is_compatible(root, "mpc86xx")) {
+ pr_warning("WARNING: your dts/dtb is old. You must update before the next kernel release\n");
+ return 1;
+ }
+
return 0;
}
-long __init
+static long __init
mpc86xx_time_init(void)
{
unsigned int temp;
--- /dev/null
+/*
+ * SBC8641D board specific routines
+ *
+ * Copyright 2008 Wind River Systems Inc.
+ *
+ * By Paul Gortmaker (see MAINTAINERS for contact information)
+ *
+ * Based largely on the 8641 HPCN support by Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/stddef.h>
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/kdev_t.h>
+#include <linux/delay.h>
+#include <linux/seq_file.h>
+#include <linux/of_platform.h>
+
+#include <asm/system.h>
+#include <asm/time.h>
+#include <asm/machdep.h>
+#include <asm/pci-bridge.h>
+#include <asm/mpc86xx.h>
+#include <asm/prom.h>
+#include <mm/mmu_decl.h>
+#include <asm/udbg.h>
+
+#include <asm/mpic.h>
+
+#include <sysdev/fsl_pci.h>
+#include <sysdev/fsl_soc.h>
+
+#include "mpc86xx.h"
+
+static void __init
+sbc8641_init_irq(void)
+{
+ struct mpic *mpic1;
+ struct device_node *np;
+ struct resource res;
+
+ /* Determine PIC address. */
+ np = of_find_node_by_type(NULL, "open-pic");
+ if (np == NULL)
+ return;
+ of_address_to_resource(np, 0, &res);
+
+ /* Alloc mpic structure and per isu has 16 INT entries. */
+ mpic1 = mpic_alloc(np, res.start,
+ MPIC_PRIMARY | MPIC_WANTS_RESET | MPIC_BIG_ENDIAN,
+ 0, 256, " MPIC ");
+ of_node_put(np);
+ BUG_ON(mpic1 == NULL);
+
+ mpic_init(mpic1);
+}
+
+static void __init
+sbc8641_setup_arch(void)
+{
+#ifdef CONFIG_PCI
+ struct device_node *np;
+#endif
+
+ if (ppc_md.progress)
+ ppc_md.progress("sbc8641_setup_arch()", 0);
+
+#ifdef CONFIG_PCI
+ for_each_compatible_node(np, "pci", "fsl,mpc8641-pcie")
+ fsl_add_bridge(np, 0);
+#endif
+
+ printk("SBC8641 board from Wind River\n");
+
+#ifdef CONFIG_SMP
+ mpc86xx_smp_init();
+#endif
+}
+
+
+static void
+sbc8641_show_cpuinfo(struct seq_file *m)
+{
+ struct device_node *root;
+ uint memsize = total_memory;
+ const char *model = "";
+ uint svid = mfspr(SPRN_SVR);
+
+ seq_printf(m, "Vendor\t\t: Wind River Systems\n");
+
+ root = of_find_node_by_path("/");
+ if (root)
+ model = of_get_property(root, "model", NULL);
+ seq_printf(m, "Machine\t\t: %s\n", model);
+ of_node_put(root);
+
+ seq_printf(m, "SVR\t\t: 0x%x\n", svid);
+ seq_printf(m, "Memory\t\t: %d MB\n", memsize / (1024 * 1024));
+}
+
+
+/*
+ * Called very early, device-tree isn't unflattened
+ */
+static int __init sbc8641_probe(void)
+{
+ unsigned long root = of_get_flat_dt_root();
+
+ if (of_flat_dt_is_compatible(root, "wind,sbc8641"))
+ return 1; /* Looks good */
+
+ return 0;
+}
+
+static long __init
+mpc86xx_time_init(void)
+{
+ unsigned int temp;
+
+ /* Set the time base to zero */
+ mtspr(SPRN_TBWL, 0);
+ mtspr(SPRN_TBWU, 0);
+
+ temp = mfspr(SPRN_HID0);
+ temp |= HID0_TBEN;
+ mtspr(SPRN_HID0, temp);
+ asm volatile("isync");
+
+ return 0;
+}
+
+static __initdata struct of_device_id of_bus_ids[] = {
+ { .compatible = "simple-bus", },
+ {},
+};
+
+static int __init declare_of_platform_devices(void)
+{
+ of_platform_bus_probe(NULL, of_bus_ids, NULL);
+
+ return 0;
+}
+machine_device_initcall(sbc8641, declare_of_platform_devices);
+
+define_machine(sbc8641) {
+ .name = "SBC8641D",
+ .probe = sbc8641_probe,
+ .setup_arch = sbc8641_setup_arch,
+ .init_IRQ = sbc8641_init_irq,
+ .show_cpuinfo = sbc8641_show_cpuinfo,
+ .get_irq = mpic_get_irq,
+ .restart = fsl_rstcr_restart,
+ .time_init = mpc86xx_time_init,
+ .calibrate_decr = generic_calibrate_decr,
+ .progress = udbg_progress,
+#ifdef CONFIG_PCI
+ .pcibios_fixup_bus = fsl_pcibios_fixup_bus,
+#endif
+};
config MPC86XADS
bool "MPC86XADS"
select CPM1
- select PPC_CPM_NEW_BINDING
help
MPC86x Application Development System by Freescale Semiconductor.
The MPC86xADS is meant to serve as a platform for s/w and h/w
config MPC885ADS
bool "MPC885ADS"
select CPM1
- select PPC_CPM_NEW_BINDING
help
Freescale Semiconductor MPC885 Application Development System (ADS).
Also known as DUET.
config PPC_EP88XC
bool "Embedded Planet EP88xC (a.k.a. CWH-PPC-885XN-VE)"
select CPM1
- select PPC_CPM_NEW_BINDING
help
This enables support for the Embedded Planet EP88xC board.
config PPC_ADDER875
bool "Analogue & Micro Adder 875"
select CPM1
- select PPC_CPM_NEW_BINDING
select REDBOOT
help
This enables support for the Analogue & Micro Adder 875
config PPC_CPM_NEW_BINDING
bool
depends on CPM1 || CPM2
- help
- Select this if your board has been converted to use the new
- device tree bindings for CPM, and no longer needs the
- ioport callbacks or the platform device glue code.
-
- The fs_enet and cpm_uart drivers will be built as
- of_platform devices.
+ default y
config AXON_RAM
tristate "Axon DDR2 memory device driver"
obj-$(CONFIG_MMIO_NVRAM) += mmio_nvram.o
obj-$(CONFIG_FSL_SOC) += fsl_soc.o
obj-$(CONFIG_FSL_PCI) += fsl_pci.o
+obj-$(CONFIG_FSL_LBC) += fsl_lbc.o
obj-$(CONFIG_RAPIDIO) += fsl_rio.o
obj-$(CONFIG_TSI108_BRIDGE) += tsi108_pci.o tsi108_dev.o
obj-$(CONFIG_QUICC_ENGINE) += qe_lib/
#define CPM_MAP_SIZE (0x4000)
-#ifndef CONFIG_PPC_CPM_NEW_BINDING
-static void m8xx_cpm_dpinit(void);
-#endif
cpm8xx_t __iomem *cpmp; /* Pointer to comm processor space */
immap_t __iomem *mpc8xx_immr;
static cpic8xx_t __iomem *cpic_reg;
out_be32(&siu_conf->sc_sdcr, 1);
immr_unmap(siu_conf);
-#ifdef CONFIG_PPC_CPM_NEW_BINDING
cpm_muram_init();
-#else
- /* Reclaim the DP memory for our use. */
- m8xx_cpm_dpinit();
-#endif
}
static DEFINE_SPINLOCK(cmd_lock);
CPM_BRG_EN | CPM_BRG_DIV16);
}
-#ifndef CONFIG_PPC_CPM_NEW_BINDING
-/*
- * dpalloc / dpfree bits.
- */
-static spinlock_t cpm_dpmem_lock;
-/*
- * 16 blocks should be enough to satisfy all requests
- * until the memory subsystem goes up...
- */
-static rh_block_t cpm_boot_dpmem_rh_block[16];
-static rh_info_t cpm_dpmem_info;
-
-#define CPM_DPMEM_ALIGNMENT 8
-static u8 __iomem *dpram_vbase;
-static phys_addr_t dpram_pbase;
-
-static void m8xx_cpm_dpinit(void)
-{
- spin_lock_init(&cpm_dpmem_lock);
-
- dpram_vbase = cpmp->cp_dpmem;
- dpram_pbase = get_immrbase() + offsetof(immap_t, im_cpm.cp_dpmem);
-
- /* Initialize the info header */
- rh_init(&cpm_dpmem_info, CPM_DPMEM_ALIGNMENT,
- sizeof(cpm_boot_dpmem_rh_block) /
- sizeof(cpm_boot_dpmem_rh_block[0]),
- cpm_boot_dpmem_rh_block);
-
- /*
- * Attach the usable dpmem area.
- * XXX: This is actually crap. CPM_DATAONLY_BASE and
- * CPM_DATAONLY_SIZE are a subset of the available dparm. It varies
- * with the processor and the microcode patches applied / activated.
- * But the following should be at least safe.
- */
- rh_attach_region(&cpm_dpmem_info, CPM_DATAONLY_BASE, CPM_DATAONLY_SIZE);
-}
-
-/*
- * Allocate the requested size worth of DP memory.
- * This function returns an offset into the DPRAM area.
- * Use cpm_dpram_addr() to get the virtual address of the area.
- */
-unsigned long cpm_dpalloc(uint size, uint align)
-{
- unsigned long start;
- unsigned long flags;
-
- spin_lock_irqsave(&cpm_dpmem_lock, flags);
- cpm_dpmem_info.alignment = align;
- start = rh_alloc(&cpm_dpmem_info, size, "commproc");
- spin_unlock_irqrestore(&cpm_dpmem_lock, flags);
-
- return (uint)start;
-}
-EXPORT_SYMBOL(cpm_dpalloc);
-
-int cpm_dpfree(unsigned long offset)
-{
- int ret;
- unsigned long flags;
-
- spin_lock_irqsave(&cpm_dpmem_lock, flags);
- ret = rh_free(&cpm_dpmem_info, offset);
- spin_unlock_irqrestore(&cpm_dpmem_lock, flags);
-
- return ret;
-}
-EXPORT_SYMBOL(cpm_dpfree);
-
-unsigned long cpm_dpalloc_fixed(unsigned long offset, uint size, uint align)
-{
- unsigned long start;
- unsigned long flags;
-
- spin_lock_irqsave(&cpm_dpmem_lock, flags);
- cpm_dpmem_info.alignment = align;
- start = rh_alloc_fixed(&cpm_dpmem_info, offset, size, "commproc");
- spin_unlock_irqrestore(&cpm_dpmem_lock, flags);
-
- return start;
-}
-EXPORT_SYMBOL(cpm_dpalloc_fixed);
-
-void cpm_dpdump(void)
-{
- rh_dump(&cpm_dpmem_info);
-}
-EXPORT_SYMBOL(cpm_dpdump);
-
-void *cpm_dpram_addr(unsigned long offset)
-{
- return (void *)(dpram_vbase + offset);
-}
-EXPORT_SYMBOL(cpm_dpram_addr);
-
-uint cpm_dpram_phys(u8 *addr)
-{
- return (dpram_pbase + (uint)(addr - dpram_vbase));
-}
-EXPORT_SYMBOL(cpm_dpram_phys);
-#endif /* !CONFIG_PPC_CPM_NEW_BINDING */
-
struct cpm_ioport16 {
__be16 dir, par, odr_sor, dat, intr;
__be16 res[3];
#include <sysdev/fsl_soc.h>
-#ifndef CONFIG_PPC_CPM_NEW_BINDING
-static void cpm2_dpinit(void);
-#endif
-
cpm_cpm2_t __iomem *cpmp; /* Pointer to comm processor space */
/* We allocate this here because it is used almost exclusively for
/* Reclaim the DP memory for our use.
*/
-#ifdef CONFIG_PPC_CPM_NEW_BINDING
cpm_muram_init();
-#else
- cpm2_dpinit();
-#endif
/* Tell everyone where the comm processor resides.
*/
cpmp = &cpm2_immr->im_cpm;
+
+#ifndef CONFIG_PPC_EARLY_DEBUG_CPM
+ /* Reset the CPM.
+ */
+ cpm_command(CPM_CR_RST, 0);
+#endif
}
static DEFINE_SPINLOCK(cmd_lock);
return ret;
}
-#ifndef CONFIG_PPC_CPM_NEW_BINDING
-/*
- * dpalloc / dpfree bits.
- */
-static spinlock_t cpm_dpmem_lock;
-/* 16 blocks should be enough to satisfy all requests
- * until the memory subsystem goes up... */
-static rh_block_t cpm_boot_dpmem_rh_block[16];
-static rh_info_t cpm_dpmem_info;
-static u8 __iomem *im_dprambase;
-
-static void cpm2_dpinit(void)
-{
- spin_lock_init(&cpm_dpmem_lock);
-
- /* initialize the info header */
- rh_init(&cpm_dpmem_info, 1,
- sizeof(cpm_boot_dpmem_rh_block) /
- sizeof(cpm_boot_dpmem_rh_block[0]),
- cpm_boot_dpmem_rh_block);
-
- im_dprambase = cpm2_immr;
-
- /* Attach the usable dpmem area */
- /* XXX: This is actually crap. CPM_DATAONLY_BASE and
- * CPM_DATAONLY_SIZE is only a subset of the available dpram. It
- * varies with the processor and the microcode patches activated.
- * But the following should be at least safe.
- */
- rh_attach_region(&cpm_dpmem_info, CPM_DATAONLY_BASE, CPM_DATAONLY_SIZE);
-}
-
-/* This function returns an index into the DPRAM area.
- */
-unsigned long cpm_dpalloc(uint size, uint align)
-{
- unsigned long start;
- unsigned long flags;
-
- spin_lock_irqsave(&cpm_dpmem_lock, flags);
- cpm_dpmem_info.alignment = align;
- start = rh_alloc(&cpm_dpmem_info, size, "commproc");
- spin_unlock_irqrestore(&cpm_dpmem_lock, flags);
-
- return (uint)start;
-}
-EXPORT_SYMBOL(cpm_dpalloc);
-
-int cpm_dpfree(unsigned long offset)
-{
- int ret;
- unsigned long flags;
-
- spin_lock_irqsave(&cpm_dpmem_lock, flags);
- ret = rh_free(&cpm_dpmem_info, offset);
- spin_unlock_irqrestore(&cpm_dpmem_lock, flags);
-
- return ret;
-}
-EXPORT_SYMBOL(cpm_dpfree);
-
-/* not sure if this is ever needed */
-unsigned long cpm_dpalloc_fixed(unsigned long offset, uint size, uint align)
-{
- unsigned long start;
- unsigned long flags;
-
- spin_lock_irqsave(&cpm_dpmem_lock, flags);
- cpm_dpmem_info.alignment = align;
- start = rh_alloc_fixed(&cpm_dpmem_info, offset, size, "commproc");
- spin_unlock_irqrestore(&cpm_dpmem_lock, flags);
-
- return start;
-}
-EXPORT_SYMBOL(cpm_dpalloc_fixed);
-
-void cpm_dpdump(void)
-{
- rh_dump(&cpm_dpmem_info);
-}
-EXPORT_SYMBOL(cpm_dpdump);
-
-void *cpm_dpram_addr(unsigned long offset)
-{
- return (void *)(im_dprambase + offset);
-}
-EXPORT_SYMBOL(cpm_dpram_addr);
-#endif /* !CONFIG_PPC_CPM_NEW_BINDING */
-
struct cpm2_ioports {
u32 dir, par, sor, odr, dat;
u32 res[3];
}
#endif
-#ifdef CONFIG_PPC_CPM_NEW_BINDING
static spinlock_t cpm_muram_lock;
static rh_block_t cpm_boot_muram_rh_block[16];
static rh_info_t cpm_muram_info;
return muram_pbase + ((u8 __iomem *)addr - muram_vbase);
}
EXPORT_SYMBOL(cpm_muram_dma);
-
-#endif /* CONFIG_PPC_CPM_NEW_BINDING */
--- /dev/null
+/*
+ * Freescale LBC and UPM routines.
+ *
+ * Copyright (c) 2007-2008 MontaVista Software, Inc.
+ *
+ * Author: Anton Vorontsov <avorontsov@ru.mvista.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/of.h>
+#include <asm/fsl_lbc.h>
+
+spinlock_t fsl_lbc_lock = __SPIN_LOCK_UNLOCKED(fsl_lbc_lock);
+
+struct fsl_lbc_regs __iomem *fsl_lbc_regs;
+EXPORT_SYMBOL(fsl_lbc_regs);
+
+static char __initdata *compat_lbc[] = {
+ "fsl,pq2-localbus",
+ "fsl,pq2pro-localbus",
+ "fsl,pq3-localbus",
+ "fsl,elbc",
+};
+
+static int __init fsl_lbc_init(void)
+{
+ struct device_node *lbus;
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(compat_lbc); i++) {
+ lbus = of_find_compatible_node(NULL, NULL, compat_lbc[i]);
+ if (lbus)
+ goto found;
+ }
+ return -ENODEV;
+
+found:
+ fsl_lbc_regs = of_iomap(lbus, 0);
+ of_node_put(lbus);
+ if (!fsl_lbc_regs)
+ return -ENOMEM;
+ return 0;
+}
+arch_initcall(fsl_lbc_init);
+
+/**
+ * fsl_lbc_find - find Localbus bank
+ * @addr_base: base address of the memory bank
+ *
+ * This function walks LBC banks comparing "Base address" field of the BR
+ * registers with the supplied addr_base argument. When bases match this
+ * function returns bank number (starting with 0), otherwise it returns
+ * appropriate errno value.
+ */
+int fsl_lbc_find(phys_addr_t addr_base)
+{
+ int i;
+
+ if (!fsl_lbc_regs)
+ return -ENODEV;
+
+ for (i = 0; i < ARRAY_SIZE(fsl_lbc_regs->bank); i++) {
+ __be32 br = in_be32(&fsl_lbc_regs->bank[i].br);
+ __be32 or = in_be32(&fsl_lbc_regs->bank[i].or);
+
+ if (br & BR_V && (br & or & BR_BA) == addr_base)
+ return i;
+ }
+
+ return -ENOENT;
+}
+EXPORT_SYMBOL(fsl_lbc_find);
+
+/**
+ * fsl_upm_find - find pre-programmed UPM via base address
+ * @addr_base: base address of the memory bank controlled by the UPM
+ * @upm: pointer to the allocated fsl_upm structure
+ *
+ * This function fills fsl_upm structure so you can use it with the rest of
+ * UPM API. On success this function returns 0, otherwise it returns
+ * appropriate errno value.
+ */
+int fsl_upm_find(phys_addr_t addr_base, struct fsl_upm *upm)
+{
+ int bank;
+ __be32 br;
+
+ bank = fsl_lbc_find(addr_base);
+ if (bank < 0)
+ return bank;
+
+ br = in_be32(&fsl_lbc_regs->bank[bank].br);
+
+ switch (br & BR_MSEL) {
+ case BR_MS_UPMA:
+ upm->mxmr = &fsl_lbc_regs->mamr;
+ break;
+ case BR_MS_UPMB:
+ upm->mxmr = &fsl_lbc_regs->mbmr;
+ break;
+ case BR_MS_UPMC:
+ upm->mxmr = &fsl_lbc_regs->mcmr;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ switch (br & BR_PS) {
+ case BR_PS_8:
+ upm->width = 8;
+ break;
+ case BR_PS_16:
+ upm->width = 16;
+ break;
+ case BR_PS_32:
+ upm->width = 32;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return 0;
+}
+EXPORT_SYMBOL(fsl_upm_find);
EXPORT_SYMBOL(get_immrbase);
+static u32 sysfreq = -1;
+
+u32 fsl_get_sys_freq(void)
+{
+ struct device_node *soc;
+ const u32 *prop;
+ int size;
+
+ if (sysfreq != -1)
+ return sysfreq;
+
+ soc = of_find_node_by_type(NULL, "soc");
+ if (!soc)
+ return -1;
+
+ prop = of_get_property(soc, "clock-frequency", &size);
+ if (!prop || size != sizeof(*prop) || *prop == 0)
+ prop = of_get_property(soc, "bus-frequency", &size);
+
+ if (prop && size == sizeof(*prop))
+ sysfreq = *prop;
+
+ of_node_put(soc);
+ return sysfreq;
+}
+EXPORT_SYMBOL(fsl_get_sys_freq);
+
#if defined(CONFIG_CPM2) || defined(CONFIG_QUICC_ENGINE) || defined(CONFIG_8xx)
static u32 brgfreq = -1;
static int __init mpc83xx_wdt_init(void)
{
struct resource r;
- struct device_node *soc, *np;
+ struct device_node *np;
struct platform_device *dev;
- const unsigned int *freq;
+ u32 freq = fsl_get_sys_freq();
int ret;
np = of_find_compatible_node(NULL, "watchdog", "mpc83xx_wdt");
goto nodev;
}
- soc = of_find_node_by_type(NULL, "soc");
-
- if (!soc) {
- ret = -ENODEV;
- goto nosoc;
- }
-
- freq = of_get_property(soc, "bus-frequency", NULL);
- if (!freq) {
- ret = -ENODEV;
- goto err;
- }
-
memset(&r, 0, sizeof(r));
ret = of_address_to_resource(np, 0, &r);
goto err;
}
- ret = platform_device_add_data(dev, freq, sizeof(int));
+ ret = platform_device_add_data(dev, &freq, sizeof(freq));
if (ret)
goto unreg;
- of_node_put(soc);
of_node_put(np);
-
return 0;
unreg:
platform_device_unregister(dev);
err:
- of_node_put(soc);
-nosoc:
of_node_put(np);
nodev:
return ret;
arch_initcall(fsl_usb_of_init);
-#ifndef CONFIG_PPC_CPM_NEW_BINDING
-#ifdef CONFIG_CPM2
-
-extern void init_scc_ioports(struct fs_uart_platform_info*);
-
-static const char fcc_regs[] = "fcc_regs";
-static const char fcc_regs_c[] = "fcc_regs_c";
-static const char fcc_pram[] = "fcc_pram";
-static char bus_id[9][BUS_ID_SIZE];
-
-static int __init fs_enet_of_init(void)
-{
- struct device_node *np;
- unsigned int i;
- struct platform_device *fs_enet_dev;
- struct resource res;
- int ret;
-
- for (np = NULL, i = 0;
- (np = of_find_compatible_node(np, "network", "fs_enet")) != NULL;
- i++) {
- struct resource r[4];
- struct device_node *phy, *mdio;
- struct fs_platform_info fs_enet_data;
- const unsigned int *id, *phy_addr, *phy_irq;
- const void *mac_addr;
- const phandle *ph;
- const char *model;
-
- memset(r, 0, sizeof(r));
- memset(&fs_enet_data, 0, sizeof(fs_enet_data));
-
- ret = of_address_to_resource(np, 0, &r[0]);
- if (ret)
- goto err;
- r[0].name = fcc_regs;
-
- ret = of_address_to_resource(np, 1, &r[1]);
- if (ret)
- goto err;
- r[1].name = fcc_pram;
-
- ret = of_address_to_resource(np, 2, &r[2]);
- if (ret)
- goto err;
- r[2].name = fcc_regs_c;
- fs_enet_data.fcc_regs_c = r[2].start;
-
- of_irq_to_resource(np, 0, &r[3]);
-
- fs_enet_dev =
- platform_device_register_simple("fsl-cpm-fcc", i, &r[0], 4);
-
- if (IS_ERR(fs_enet_dev)) {
- ret = PTR_ERR(fs_enet_dev);
- goto err;
- }
-
- model = of_get_property(np, "model", NULL);
- if (model == NULL) {
- ret = -ENODEV;
- goto unreg;
- }
-
- mac_addr = of_get_mac_address(np);
- if (mac_addr)
- memcpy(fs_enet_data.macaddr, mac_addr, 6);
-
- ph = of_get_property(np, "phy-handle", NULL);
- phy = of_find_node_by_phandle(*ph);
-
- if (phy == NULL) {
- ret = -ENODEV;
- goto unreg;
- }
-
- phy_addr = of_get_property(phy, "reg", NULL);
- fs_enet_data.phy_addr = *phy_addr;
-
- phy_irq = of_get_property(phy, "interrupts", NULL);
-
- id = of_get_property(np, "device-id", NULL);
- fs_enet_data.fs_no = *id;
- strcpy(fs_enet_data.fs_type, model);
-
- mdio = of_get_parent(phy);
- ret = of_address_to_resource(mdio, 0, &res);
- if (ret) {
- of_node_put(phy);
- of_node_put(mdio);
- goto unreg;
- }
-
- fs_enet_data.clk_rx = *((u32 *)of_get_property(np,
- "rx-clock", NULL));
- fs_enet_data.clk_tx = *((u32 *)of_get_property(np,
- "tx-clock", NULL));
-
- if (strstr(model, "FCC")) {
- int fcc_index = *id - 1;
- const unsigned char *mdio_bb_prop;
-
- fs_enet_data.dpram_offset = (u32)cpm_dpram_addr(0);
- fs_enet_data.rx_ring = 32;
- fs_enet_data.tx_ring = 32;
- fs_enet_data.rx_copybreak = 240;
- fs_enet_data.use_napi = 0;
- fs_enet_data.napi_weight = 17;
- fs_enet_data.mem_offset = FCC_MEM_OFFSET(fcc_index);
- fs_enet_data.cp_page = CPM_CR_FCC_PAGE(fcc_index);
- fs_enet_data.cp_block = CPM_CR_FCC_SBLOCK(fcc_index);
-
- snprintf((char*)&bus_id[(*id)], BUS_ID_SIZE, "%x:%02x",
- (u32)res.start, fs_enet_data.phy_addr);
- fs_enet_data.bus_id = (char*)&bus_id[(*id)];
- fs_enet_data.init_ioports = init_fcc_ioports;
-
- mdio_bb_prop = of_get_property(phy, "bitbang", NULL);
- if (mdio_bb_prop) {
- struct platform_device *fs_enet_mdio_bb_dev;
- struct fs_mii_bb_platform_info fs_enet_mdio_bb_data;
-
- fs_enet_mdio_bb_dev =
- platform_device_register_simple("fsl-bb-mdio",
- i, NULL, 0);
- memset(&fs_enet_mdio_bb_data, 0,
- sizeof(struct fs_mii_bb_platform_info));
- fs_enet_mdio_bb_data.mdio_dat.bit =
- mdio_bb_prop[0];
- fs_enet_mdio_bb_data.mdio_dir.bit =
- mdio_bb_prop[1];
- fs_enet_mdio_bb_data.mdc_dat.bit =
- mdio_bb_prop[2];
- fs_enet_mdio_bb_data.mdio_port =
- mdio_bb_prop[3];
- fs_enet_mdio_bb_data.mdc_port =
- mdio_bb_prop[4];
- fs_enet_mdio_bb_data.delay =
- mdio_bb_prop[5];
-
- fs_enet_mdio_bb_data.irq[0] = phy_irq[0];
- fs_enet_mdio_bb_data.irq[1] = -1;
- fs_enet_mdio_bb_data.irq[2] = -1;
- fs_enet_mdio_bb_data.irq[3] = phy_irq[0];
- fs_enet_mdio_bb_data.irq[31] = -1;
-
- fs_enet_mdio_bb_data.mdio_dat.offset =
- (u32)&cpm2_immr->im_ioport.iop_pdatc;
- fs_enet_mdio_bb_data.mdio_dir.offset =
- (u32)&cpm2_immr->im_ioport.iop_pdirc;
- fs_enet_mdio_bb_data.mdc_dat.offset =
- (u32)&cpm2_immr->im_ioport.iop_pdatc;
-
- ret = platform_device_add_data(
- fs_enet_mdio_bb_dev,
- &fs_enet_mdio_bb_data,
- sizeof(struct fs_mii_bb_platform_info));
- if (ret)
- goto unreg;
- }
-
- of_node_put(phy);
- of_node_put(mdio);
-
- ret = platform_device_add_data(fs_enet_dev, &fs_enet_data,
- sizeof(struct
- fs_platform_info));
- if (ret)
- goto unreg;
- }
- }
- return 0;
-
-unreg:
- platform_device_unregister(fs_enet_dev);
-err:
- return ret;
-}
-
-arch_initcall(fs_enet_of_init);
-
-static const char scc_regs[] = "regs";
-static const char scc_pram[] = "pram";
-
-static int __init cpm_uart_of_init(void)
-{
- struct device_node *np;
- unsigned int i;
- struct platform_device *cpm_uart_dev;
- int ret;
-
- for (np = NULL, i = 0;
- (np = of_find_compatible_node(np, "serial", "cpm_uart")) != NULL;
- i++) {
- struct resource r[3];
- struct fs_uart_platform_info cpm_uart_data;
- const int *id;
- const char *model;
-
- memset(r, 0, sizeof(r));
- memset(&cpm_uart_data, 0, sizeof(cpm_uart_data));
-
- ret = of_address_to_resource(np, 0, &r[0]);
- if (ret)
- goto err;
-
- r[0].name = scc_regs;
-
- ret = of_address_to_resource(np, 1, &r[1]);
- if (ret)
- goto err;
- r[1].name = scc_pram;
-
- of_irq_to_resource(np, 0, &r[2]);
-
- cpm_uart_dev =
- platform_device_register_simple("fsl-cpm-scc:uart", i, &r[0], 3);
-
- if (IS_ERR(cpm_uart_dev)) {
- ret = PTR_ERR(cpm_uart_dev);
- goto err;
- }
-
- id = of_get_property(np, "device-id", NULL);
- cpm_uart_data.fs_no = *id;
-
- model = of_get_property(np, "model", NULL);
- strcpy(cpm_uart_data.fs_type, model);
-
- cpm_uart_data.uart_clk = ppc_proc_freq;
-
- cpm_uart_data.tx_num_fifo = 4;
- cpm_uart_data.tx_buf_size = 32;
- cpm_uart_data.rx_num_fifo = 4;
- cpm_uart_data.rx_buf_size = 32;
- cpm_uart_data.clk_rx = *((u32 *)of_get_property(np,
- "rx-clock", NULL));
- cpm_uart_data.clk_tx = *((u32 *)of_get_property(np,
- "tx-clock", NULL));
-
- ret =
- platform_device_add_data(cpm_uart_dev, &cpm_uart_data,
- sizeof(struct
- fs_uart_platform_info));
- if (ret)
- goto unreg;
- }
-
- return 0;
-
-unreg:
- platform_device_unregister(cpm_uart_dev);
-err:
- return ret;
-}
-
-arch_initcall(cpm_uart_of_init);
-#endif /* CONFIG_CPM2 */
-
-#ifdef CONFIG_8xx
-
-extern void init_scc_ioports(struct fs_platform_info*);
-extern int platform_device_skip(const char *model, int id);
-
-static int __init fs_enet_mdio_of_init(void)
-{
- struct device_node *np;
- unsigned int i;
- struct platform_device *mdio_dev;
- struct resource res;
- int ret;
-
- for (np = NULL, i = 0;
- (np = of_find_compatible_node(np, "mdio", "fs_enet")) != NULL;
- i++) {
- struct fs_mii_fec_platform_info mdio_data;
-
- memset(&res, 0, sizeof(res));
- memset(&mdio_data, 0, sizeof(mdio_data));
-
- ret = of_address_to_resource(np, 0, &res);
- if (ret)
- goto err;
-
- mdio_dev =
- platform_device_register_simple("fsl-cpm-fec-mdio",
- res.start, &res, 1);
- if (IS_ERR(mdio_dev)) {
- ret = PTR_ERR(mdio_dev);
- goto err;
- }
-
- mdio_data.mii_speed = ((((ppc_proc_freq + 4999999) / 2500000) / 2) & 0x3F) << 1;
-
- ret =
- platform_device_add_data(mdio_dev, &mdio_data,
- sizeof(struct fs_mii_fec_platform_info));
- if (ret)
- goto unreg;
- }
- return 0;
-
-unreg:
- platform_device_unregister(mdio_dev);
-err:
- return ret;
-}
-
-arch_initcall(fs_enet_mdio_of_init);
-
-static const char *enet_regs = "regs";
-static const char *enet_pram = "pram";
-static const char *enet_irq = "interrupt";
-static char bus_id[9][BUS_ID_SIZE];
-
-static int __init fs_enet_of_init(void)
-{
- struct device_node *np;
- unsigned int i;
- struct platform_device *fs_enet_dev = NULL;
- struct resource res;
- int ret;
-
- for (np = NULL, i = 0;
- (np = of_find_compatible_node(np, "network", "fs_enet")) != NULL;
- i++) {
- struct resource r[4];
- struct device_node *phy = NULL, *mdio = NULL;
- struct fs_platform_info fs_enet_data;
- const unsigned int *id;
- const unsigned int *phy_addr;
- const void *mac_addr;
- const phandle *ph;
- const char *model;
-
- memset(r, 0, sizeof(r));
- memset(&fs_enet_data, 0, sizeof(fs_enet_data));
-
- model = of_get_property(np, "model", NULL);
- if (model == NULL) {
- ret = -ENODEV;
- goto unreg;
- }
-
- id = of_get_property(np, "device-id", NULL);
- fs_enet_data.fs_no = *id;
-
- if (platform_device_skip(model, *id))
- continue;
-
- ret = of_address_to_resource(np, 0, &r[0]);
- if (ret)
- goto err;
- r[0].name = enet_regs;
-
- mac_addr = of_get_mac_address(np);
- if (mac_addr)
- memcpy(fs_enet_data.macaddr, mac_addr, 6);
-
- ph = of_get_property(np, "phy-handle", NULL);
- if (ph != NULL)
- phy = of_find_node_by_phandle(*ph);
-
- if (phy != NULL) {
- phy_addr = of_get_property(phy, "reg", NULL);
- fs_enet_data.phy_addr = *phy_addr;
- fs_enet_data.has_phy = 1;
-
- mdio = of_get_parent(phy);
- ret = of_address_to_resource(mdio, 0, &res);
- if (ret) {
- of_node_put(phy);
- of_node_put(mdio);
- goto unreg;
- }
- }
-
- model = of_get_property(np, "model", NULL);
- strcpy(fs_enet_data.fs_type, model);
-
- if (strstr(model, "FEC")) {
- r[1].start = r[1].end = irq_of_parse_and_map(np, 0);
- r[1].flags = IORESOURCE_IRQ;
- r[1].name = enet_irq;
-
- fs_enet_dev =
- platform_device_register_simple("fsl-cpm-fec", i, &r[0], 2);
-
- if (IS_ERR(fs_enet_dev)) {
- ret = PTR_ERR(fs_enet_dev);
- goto err;
- }
-
- fs_enet_data.rx_ring = 128;
- fs_enet_data.tx_ring = 16;
- fs_enet_data.rx_copybreak = 240;
- fs_enet_data.use_napi = 1;
- fs_enet_data.napi_weight = 17;
-
- snprintf((char*)&bus_id[i], BUS_ID_SIZE, "%x:%02x",
- (u32)res.start, fs_enet_data.phy_addr);
- fs_enet_data.bus_id = (char*)&bus_id[i];
- fs_enet_data.init_ioports = init_fec_ioports;
- }
- if (strstr(model, "SCC")) {
- ret = of_address_to_resource(np, 1, &r[1]);
- if (ret)
- goto err;
- r[1].name = enet_pram;
-
- r[2].start = r[2].end = irq_of_parse_and_map(np, 0);
- r[2].flags = IORESOURCE_IRQ;
- r[2].name = enet_irq;
-
- fs_enet_dev =
- platform_device_register_simple("fsl-cpm-scc", i, &r[0], 3);
-
- if (IS_ERR(fs_enet_dev)) {
- ret = PTR_ERR(fs_enet_dev);
- goto err;
- }
-
- fs_enet_data.rx_ring = 64;
- fs_enet_data.tx_ring = 8;
- fs_enet_data.rx_copybreak = 240;
- fs_enet_data.use_napi = 1;
- fs_enet_data.napi_weight = 17;
-
- snprintf((char*)&bus_id[i], BUS_ID_SIZE, "%s", "fixed@10:1");
- fs_enet_data.bus_id = (char*)&bus_id[i];
- fs_enet_data.init_ioports = init_scc_ioports;
- }
-
- of_node_put(phy);
- of_node_put(mdio);
-
- ret = platform_device_add_data(fs_enet_dev, &fs_enet_data,
- sizeof(struct
- fs_platform_info));
- if (ret)
- goto unreg;
- }
- return 0;
-
-unreg:
- platform_device_unregister(fs_enet_dev);
-err:
- return ret;
-}
-
-arch_initcall(fs_enet_of_init);
-
-static int __init fsl_pcmcia_of_init(void)
-{
- struct device_node *np;
- /*
- * Register all the devices which type is "pcmcia"
- */
- for_each_compatible_node(np, "pcmcia", "fsl,pq-pcmcia")
- of_platform_device_create(np, "m8xx-pcmcia", NULL);
- return 0;
-}
-
-arch_initcall(fsl_pcmcia_of_init);
-
-static const char *smc_regs = "regs";
-static const char *smc_pram = "pram";
-
-static int __init cpm_smc_uart_of_init(void)
-{
- struct device_node *np;
- unsigned int i;
- struct platform_device *cpm_uart_dev;
- int ret;
-
- for (np = NULL, i = 0;
- (np = of_find_compatible_node(np, "serial", "cpm_uart")) != NULL;
- i++) {
- struct resource r[3];
- struct fs_uart_platform_info cpm_uart_data;
- const int *id;
- const char *model;
-
- memset(r, 0, sizeof(r));
- memset(&cpm_uart_data, 0, sizeof(cpm_uart_data));
-
- ret = of_address_to_resource(np, 0, &r[0]);
- if (ret)
- goto err;
-
- r[0].name = smc_regs;
-
- ret = of_address_to_resource(np, 1, &r[1]);
- if (ret)
- goto err;
- r[1].name = smc_pram;
-
- r[2].start = r[2].end = irq_of_parse_and_map(np, 0);
- r[2].flags = IORESOURCE_IRQ;
-
- cpm_uart_dev =
- platform_device_register_simple("fsl-cpm-smc:uart", i, &r[0], 3);
-
- if (IS_ERR(cpm_uart_dev)) {
- ret = PTR_ERR(cpm_uart_dev);
- goto err;
- }
-
- model = of_get_property(np, "model", NULL);
- strcpy(cpm_uart_data.fs_type, model);
-
- id = of_get_property(np, "device-id", NULL);
- cpm_uart_data.fs_no = *id;
- cpm_uart_data.uart_clk = ppc_proc_freq;
-
- cpm_uart_data.tx_num_fifo = 4;
- cpm_uart_data.tx_buf_size = 32;
- cpm_uart_data.rx_num_fifo = 4;
- cpm_uart_data.rx_buf_size = 32;
-
- ret =
- platform_device_add_data(cpm_uart_dev, &cpm_uart_data,
- sizeof(struct
- fs_uart_platform_info));
- if (ret)
- goto unreg;
- }
-
- return 0;
-
-unreg:
- platform_device_unregister(cpm_uart_dev);
-err:
- return ret;
-}
-
-arch_initcall(cpm_smc_uart_of_init);
-
-#endif /* CONFIG_8xx */
-#endif /* CONFIG_PPC_CPM_NEW_BINDING */
-
static int __init of_fsl_spi_probe(char *type, char *compatible, u32 sysclk,
struct spi_board_info *board_infos,
unsigned int num_board_infos,
sysclk = get_brgfreq();
#endif
if (sysclk == -1) {
- struct device_node *np;
- const u32 *freq;
- int size;
-
- np = of_find_node_by_type(NULL, "soc");
- if (!np)
+ sysclk = fsl_get_sys_freq();
+ if (sysclk == -1)
return -ENODEV;
-
- freq = of_get_property(np, "clock-frequency", &size);
- if (!freq || size != sizeof(*freq) || *freq == 0) {
- freq = of_get_property(np, "bus-frequency", &size);
- if (!freq || size != sizeof(*freq) || *freq == 0) {
- of_node_put(np);
- return -ENODEV;
- }
- }
-
- sysclk = *freq;
- of_node_put(np);
}
ret = of_fsl_spi_probe(NULL, "fsl,spi", sysclk, board_infos,
extern phys_addr_t get_immrbase(void);
extern u32 get_brgfreq(void);
extern u32 get_baudrate(void);
+extern u32 fsl_get_sys_freq(void);
struct spi_board_info;
/* We allocate this here because it is used almost exclusively for
* the communication processor devices.
*/
-struct qe_immap *qe_immr = NULL;
+struct qe_immap __iomem *qe_immr;
EXPORT_SYMBOL(qe_immr);
static struct qe_snum snums[QE_NUM_OF_SNUM]; /* Dynamically allocated SNUMs */
*/
static unsigned int brg_clk = 0;
-unsigned int get_brg_clk(void)
+unsigned int qe_get_brg_clk(void)
{
struct device_node *qe;
unsigned int size;
return brg_clk;
}
+EXPORT_SYMBOL(qe_get_brg_clk);
/* Program the BRG to the given sampling rate and multiplier
*
if ((brg < QE_BRG1) || (brg > QE_BRG16))
return -EINVAL;
- divisor = get_brg_clk() / (rate * multiplier);
+ divisor = qe_get_brg_clk() / (rate * multiplier);
if (divisor > QE_BRGC_DIVISOR_MAX + 1) {
div16 = QE_BRGC_DIV16;
}
EXPORT_SYMBOL(qe_muram_dump);
-void *qe_muram_addr(unsigned long offset)
-{
- return (void *)&qe_immr->muram[offset];
-}
-EXPORT_SYMBOL(qe_muram_addr);
-
/* The maximum number of RISCs we support */
#define MAX_QE_RISC 2
#include <linux/ioport.h>
#include <asm/io.h>
+#include <asm/qe.h>
#include <asm/prom.h>
#include <sysdev/fsl_soc.h>
#endif
};
-static struct port_regs *par_io = NULL;
+static struct port_regs __iomem *par_io;
static int num_par_io_ports = 0;
int par_io_init(struct device_node *np)
}
ph = of_get_property(np, "pio-handle", NULL);
- if (ph == 0) {
+ if (ph == NULL) {
printk(KERN_ERR "pio-handle not available \n");
return -1;
}
#include <linux/mtd/partitions.h>
#include <asm/io.h>
-
+#include <asm/fsl_lbc.h>
#define MAX_BANKS 8
#define ERR_BYTE 0xFF /* Value returned for read bytes when read failed */
#define FCM_TIMEOUT_MSECS 500 /* Maximum number of mSecs to wait for FCM */
-struct elbc_bank {
- __be32 br; /**< Base Register */
-#define BR_BA 0xFFFF8000
-#define BR_BA_SHIFT 15
-#define BR_PS 0x00001800
-#define BR_PS_SHIFT 11
-#define BR_PS_8 0x00000800 /* Port Size 8 bit */
-#define BR_PS_16 0x00001000 /* Port Size 16 bit */
-#define BR_PS_32 0x00001800 /* Port Size 32 bit */
-#define BR_DECC 0x00000600
-#define BR_DECC_SHIFT 9
-#define BR_DECC_OFF 0x00000000 /* HW ECC checking and generation off */
-#define BR_DECC_CHK 0x00000200 /* HW ECC checking on, generation off */
-#define BR_DECC_CHK_GEN 0x00000400 /* HW ECC checking and generation on */
-#define BR_WP 0x00000100
-#define BR_WP_SHIFT 8
-#define BR_MSEL 0x000000E0
-#define BR_MSEL_SHIFT 5
-#define BR_MS_GPCM 0x00000000 /* GPCM */
-#define BR_MS_FCM 0x00000020 /* FCM */
-#define BR_MS_SDRAM 0x00000060 /* SDRAM */
-#define BR_MS_UPMA 0x00000080 /* UPMA */
-#define BR_MS_UPMB 0x000000A0 /* UPMB */
-#define BR_MS_UPMC 0x000000C0 /* UPMC */
-#define BR_V 0x00000001
-#define BR_V_SHIFT 0
-#define BR_RES ~(BR_BA|BR_PS|BR_DECC|BR_WP|BR_MSEL|BR_V)
-
- __be32 or; /**< Base Register */
-#define OR0 0x5004
-#define OR1 0x500C
-#define OR2 0x5014
-#define OR3 0x501C
-#define OR4 0x5024
-#define OR5 0x502C
-#define OR6 0x5034
-#define OR7 0x503C
-
-#define OR_FCM_AM 0xFFFF8000
-#define OR_FCM_AM_SHIFT 15
-#define OR_FCM_BCTLD 0x00001000
-#define OR_FCM_BCTLD_SHIFT 12
-#define OR_FCM_PGS 0x00000400
-#define OR_FCM_PGS_SHIFT 10
-#define OR_FCM_CSCT 0x00000200
-#define OR_FCM_CSCT_SHIFT 9
-#define OR_FCM_CST 0x00000100
-#define OR_FCM_CST_SHIFT 8
-#define OR_FCM_CHT 0x00000080
-#define OR_FCM_CHT_SHIFT 7
-#define OR_FCM_SCY 0x00000070
-#define OR_FCM_SCY_SHIFT 4
-#define OR_FCM_SCY_1 0x00000010
-#define OR_FCM_SCY_2 0x00000020
-#define OR_FCM_SCY_3 0x00000030
-#define OR_FCM_SCY_4 0x00000040
-#define OR_FCM_SCY_5 0x00000050
-#define OR_FCM_SCY_6 0x00000060
-#define OR_FCM_SCY_7 0x00000070
-#define OR_FCM_RST 0x00000008
-#define OR_FCM_RST_SHIFT 3
-#define OR_FCM_TRLX 0x00000004
-#define OR_FCM_TRLX_SHIFT 2
-#define OR_FCM_EHTR 0x00000002
-#define OR_FCM_EHTR_SHIFT 1
-};
-
-struct elbc_regs {
- struct elbc_bank bank[8];
- u8 res0[0x28];
- __be32 mar; /**< UPM Address Register */
- u8 res1[0x4];
- __be32 mamr; /**< UPMA Mode Register */
- __be32 mbmr; /**< UPMB Mode Register */
- __be32 mcmr; /**< UPMC Mode Register */
- u8 res2[0x8];
- __be32 mrtpr; /**< Memory Refresh Timer Prescaler Register */
- __be32 mdr; /**< UPM Data Register */
- u8 res3[0x4];
- __be32 lsor; /**< Special Operation Initiation Register */
- __be32 lsdmr; /**< SDRAM Mode Register */
- u8 res4[0x8];
- __be32 lurt; /**< UPM Refresh Timer */
- __be32 lsrt; /**< SDRAM Refresh Timer */
- u8 res5[0x8];
- __be32 ltesr; /**< Transfer Error Status Register */
-#define LTESR_BM 0x80000000
-#define LTESR_FCT 0x40000000
-#define LTESR_PAR 0x20000000
-#define LTESR_WP 0x04000000
-#define LTESR_ATMW 0x00800000
-#define LTESR_ATMR 0x00400000
-#define LTESR_CS 0x00080000
-#define LTESR_CC 0x00000001
-#define LTESR_NAND_MASK (LTESR_FCT | LTESR_PAR | LTESR_CC)
- __be32 ltedr; /**< Transfer Error Disable Register */
- __be32 lteir; /**< Transfer Error Interrupt Register */
- __be32 lteatr; /**< Transfer Error Attributes Register */
- __be32 ltear; /**< Transfer Error Address Register */
- u8 res6[0xC];
- __be32 lbcr; /**< Configuration Register */
-#define LBCR_LDIS 0x80000000
-#define LBCR_LDIS_SHIFT 31
-#define LBCR_BCTLC 0x00C00000
-#define LBCR_BCTLC_SHIFT 22
-#define LBCR_AHD 0x00200000
-#define LBCR_LPBSE 0x00020000
-#define LBCR_LPBSE_SHIFT 17
-#define LBCR_EPAR 0x00010000
-#define LBCR_EPAR_SHIFT 16
-#define LBCR_BMT 0x0000FF00
-#define LBCR_BMT_SHIFT 8
-#define LBCR_INIT 0x00040000
- __be32 lcrr; /**< Clock Ratio Register */
-#define LCRR_DBYP 0x80000000
-#define LCRR_DBYP_SHIFT 31
-#define LCRR_BUFCMDC 0x30000000
-#define LCRR_BUFCMDC_SHIFT 28
-#define LCRR_ECL 0x03000000
-#define LCRR_ECL_SHIFT 24
-#define LCRR_EADC 0x00030000
-#define LCRR_EADC_SHIFT 16
-#define LCRR_CLKDIV 0x0000000F
-#define LCRR_CLKDIV_SHIFT 0
- u8 res7[0x8];
- __be32 fmr; /**< Flash Mode Register */
-#define FMR_CWTO 0x0000F000
-#define FMR_CWTO_SHIFT 12
-#define FMR_BOOT 0x00000800
-#define FMR_ECCM 0x00000100
-#define FMR_AL 0x00000030
-#define FMR_AL_SHIFT 4
-#define FMR_OP 0x00000003
-#define FMR_OP_SHIFT 0
- __be32 fir; /**< Flash Instruction Register */
-#define FIR_OP0 0xF0000000
-#define FIR_OP0_SHIFT 28
-#define FIR_OP1 0x0F000000
-#define FIR_OP1_SHIFT 24
-#define FIR_OP2 0x00F00000
-#define FIR_OP2_SHIFT 20
-#define FIR_OP3 0x000F0000
-#define FIR_OP3_SHIFT 16
-#define FIR_OP4 0x0000F000
-#define FIR_OP4_SHIFT 12
-#define FIR_OP5 0x00000F00
-#define FIR_OP5_SHIFT 8
-#define FIR_OP6 0x000000F0
-#define FIR_OP6_SHIFT 4
-#define FIR_OP7 0x0000000F
-#define FIR_OP7_SHIFT 0
-#define FIR_OP_NOP 0x0 /* No operation and end of sequence */
-#define FIR_OP_CA 0x1 /* Issue current column address */
-#define FIR_OP_PA 0x2 /* Issue current block+page address */
-#define FIR_OP_UA 0x3 /* Issue user defined address */
-#define FIR_OP_CM0 0x4 /* Issue command from FCR[CMD0] */
-#define FIR_OP_CM1 0x5 /* Issue command from FCR[CMD1] */
-#define FIR_OP_CM2 0x6 /* Issue command from FCR[CMD2] */
-#define FIR_OP_CM3 0x7 /* Issue command from FCR[CMD3] */
-#define FIR_OP_WB 0x8 /* Write FBCR bytes from FCM buffer */
-#define FIR_OP_WS 0x9 /* Write 1 or 2 bytes from MDR[AS] */
-#define FIR_OP_RB 0xA /* Read FBCR bytes to FCM buffer */
-#define FIR_OP_RS 0xB /* Read 1 or 2 bytes to MDR[AS] */
-#define FIR_OP_CW0 0xC /* Wait then issue FCR[CMD0] */
-#define FIR_OP_CW1 0xD /* Wait then issue FCR[CMD1] */
-#define FIR_OP_RBW 0xE /* Wait then read FBCR bytes */
-#define FIR_OP_RSW 0xE /* Wait then read 1 or 2 bytes */
- __be32 fcr; /**< Flash Command Register */
-#define FCR_CMD0 0xFF000000
-#define FCR_CMD0_SHIFT 24
-#define FCR_CMD1 0x00FF0000
-#define FCR_CMD1_SHIFT 16
-#define FCR_CMD2 0x0000FF00
-#define FCR_CMD2_SHIFT 8
-#define FCR_CMD3 0x000000FF
-#define FCR_CMD3_SHIFT 0
- __be32 fbar; /**< Flash Block Address Register */
-#define FBAR_BLK 0x00FFFFFF
- __be32 fpar; /**< Flash Page Address Register */
-#define FPAR_SP_PI 0x00007C00
-#define FPAR_SP_PI_SHIFT 10
-#define FPAR_SP_MS 0x00000200
-#define FPAR_SP_CI 0x000001FF
-#define FPAR_SP_CI_SHIFT 0
-#define FPAR_LP_PI 0x0003F000
-#define FPAR_LP_PI_SHIFT 12
-#define FPAR_LP_MS 0x00000800
-#define FPAR_LP_CI 0x000007FF
-#define FPAR_LP_CI_SHIFT 0
- __be32 fbcr; /**< Flash Byte Count Register */
-#define FBCR_BC 0x00000FFF
- u8 res11[0x8];
- u8 res8[0xF00];
-};
-
struct fsl_elbc_ctrl;
/* mtd information per set */
/* device info */
struct device *dev;
- struct elbc_regs __iomem *regs;
+ struct fsl_lbc_regs __iomem *regs;
int irq;
wait_queue_head_t irq_wait;
unsigned int irq_status; /* status read from LTESR by irq handler */
struct nand_chip *chip = mtd->priv;
struct fsl_elbc_mtd *priv = chip->priv;
struct fsl_elbc_ctrl *ctrl = priv->ctrl;
- struct elbc_regs __iomem *lbc = ctrl->regs;
+ struct fsl_lbc_regs __iomem *lbc = ctrl->regs;
int buf_num;
ctrl->page = page_addr;
struct nand_chip *chip = mtd->priv;
struct fsl_elbc_mtd *priv = chip->priv;
struct fsl_elbc_ctrl *ctrl = priv->ctrl;
- struct elbc_regs __iomem *lbc = ctrl->regs;
+ struct fsl_lbc_regs __iomem *lbc = ctrl->regs;
/* Setup the FMR[OP] to execute without write protection */
out_be32(&lbc->fmr, priv->fmr | 3);
{
struct fsl_elbc_mtd *priv = chip->priv;
struct fsl_elbc_ctrl *ctrl = priv->ctrl;
- struct elbc_regs __iomem *lbc = ctrl->regs;
+ struct fsl_lbc_regs __iomem *lbc = ctrl->regs;
if (priv->page_size) {
out_be32(&lbc->fir,
struct nand_chip *chip = mtd->priv;
struct fsl_elbc_mtd *priv = chip->priv;
struct fsl_elbc_ctrl *ctrl = priv->ctrl;
- struct elbc_regs __iomem *lbc = ctrl->regs;
+ struct fsl_lbc_regs __iomem *lbc = ctrl->regs;
ctrl->use_mdr = 0;
{
struct fsl_elbc_mtd *priv = chip->priv;
struct fsl_elbc_ctrl *ctrl = priv->ctrl;
- struct elbc_regs __iomem *lbc = ctrl->regs;
+ struct fsl_lbc_regs __iomem *lbc = ctrl->regs;
if (ctrl->status != LTESR_CC)
return NAND_STATUS_FAIL;
struct nand_chip *chip = mtd->priv;
struct fsl_elbc_mtd *priv = chip->priv;
struct fsl_elbc_ctrl *ctrl = priv->ctrl;
- struct elbc_regs __iomem *lbc = ctrl->regs;
+ struct fsl_lbc_regs __iomem *lbc = ctrl->regs;
unsigned int al;
/* calculate FMR Address Length field */
static int fsl_elbc_chip_init(struct fsl_elbc_mtd *priv)
{
struct fsl_elbc_ctrl *ctrl = priv->ctrl;
- struct elbc_regs __iomem *lbc = ctrl->regs;
+ struct fsl_lbc_regs __iomem *lbc = ctrl->regs;
struct nand_chip *chip = &priv->chip;
dev_dbg(priv->dev, "eLBC Set Information for bank %d\n", priv->bank);
static int fsl_elbc_chip_probe(struct fsl_elbc_ctrl *ctrl,
struct device_node *node)
{
- struct elbc_regs __iomem *lbc = ctrl->regs;
+ struct fsl_lbc_regs __iomem *lbc = ctrl->regs;
struct fsl_elbc_mtd *priv;
struct resource res;
#ifdef CONFIG_MTD_PARTITIONS
static int __devinit fsl_elbc_ctrl_init(struct fsl_elbc_ctrl *ctrl)
{
- struct elbc_regs __iomem *lbc = ctrl->regs;
+ struct fsl_lbc_regs __iomem *lbc = ctrl->regs;
/* clear event registers */
setbits32(&lbc->ltesr, LTESR_NAND_MASK);
static irqreturn_t fsl_elbc_ctrl_irq(int irqno, void *data)
{
struct fsl_elbc_ctrl *ctrl = data;
- struct elbc_regs __iomem *lbc = ctrl->regs;
+ struct fsl_lbc_regs __iomem *lbc = ctrl->regs;
__be32 status = in_be32(&lbc->ltesr) & LTESR_NAND_MASK;
if (status) {
ugeth_vdbg("%s: IN", __FUNCTION__);
- prop = of_get_property(np, "device-id", NULL);
+ prop = of_get_property(np, "cell-index", NULL);
+ if (!prop) {
+ prop = of_get_property(np, "device-id", NULL);
+ if (!prop)
+ return -ENODEV;
+ }
+
ucc_num = *prop - 1;
if ((ucc_num < 0) || (ucc_num > 7))
return -ENODEV;
if ((res.start >= tempres.start) &&
(res.end <= tempres.end)) {
/* set this UCC to be the MII master */
- const u32 *id = of_get_property(tempnp, "device-id", NULL);
- if (id == NULL)
- goto bus_register_fail;
+ const u32 *id;
+
+ id = of_get_property(tempnp, "cell-index", NULL);
+ if (!id) {
+ id = of_get_property(tempnp, "device-id", NULL);
+ if (!id)
+ goto bus_register_fail;
+ }
ucc_set_qe_mux_mii_mng(*id - 1);
/* these are located in their respective files */
void cpm_line_cr_cmd(struct uart_cpm_port *port, int cmd);
+void __iomem *cpm_uart_map_pram(struct uart_cpm_port *port,
+ struct device_node *np);
+void cpm_uart_unmap_pram(struct uart_cpm_port *port, void __iomem *pram);
int cpm_uart_init_portdesc(void);
int cpm_uart_allocbuf(struct uart_cpm_port *pinfo, unsigned int is_con);
void cpm_uart_freebuf(struct uart_cpm_port *pinfo);
if (!mem)
return -ENOMEM;
- pram = of_iomap(np, 1);
- if (!pram) {
- ret = -ENOMEM;
- goto out_mem;
- }
-
if (of_device_is_compatible(np, "fsl,cpm1-scc-uart") ||
of_device_is_compatible(np, "fsl,cpm2-scc-uart")) {
pinfo->sccp = mem;
- pinfo->sccup = pram;
+ pinfo->sccup = pram = cpm_uart_map_pram(pinfo, np);
} else if (of_device_is_compatible(np, "fsl,cpm1-smc-uart") ||
of_device_is_compatible(np, "fsl,cpm2-smc-uart")) {
pinfo->flags |= FLAG_SMC;
pinfo->smcp = mem;
- pinfo->smcup = pram;
+ pinfo->smcup = pram = cpm_uart_map_pram(pinfo, np);
} else {
ret = -ENODEV;
- goto out_pram;
+ goto out_mem;
+ }
+
+ if (!pram) {
+ ret = -ENOMEM;
+ goto out_mem;
}
pinfo->tx_nrfifos = TX_NUM_FIFO;
return cpm_uart_request_port(&pinfo->port);
out_pram:
- iounmap(pram);
+ cpm_uart_unmap_pram(pinfo, pram);
out_mem:
iounmap(mem);
return ret;
#include <linux/serial_core.h>
#include <linux/kernel.h>
+#include <linux/of.h>
+
#include "cpm_uart.h"
/**************************************************************/
{
cpm_command(port->command, cmd);
}
+
+void __iomem *cpm_uart_map_pram(struct uart_cpm_port *port,
+ struct device_node *np)
+{
+ return of_iomap(np, 1);
+}
+
+void cpm_uart_unmap_pram(struct uart_cpm_port *port, void __iomem *pram)
+{
+ iounmap(pram);
+}
+
#else
void cpm_line_cr_cmd(struct uart_cpm_port *port, int cmd)
{
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/fs_pd.h>
+#ifdef CONFIG_PPC_CPM_NEW_BINDING
+#include <asm/prom.h>
+#endif
#include <linux/serial_core.h>
#include <linux/kernel.h>
{
cpm_command(port->command, cmd);
}
+
+void __iomem *cpm_uart_map_pram(struct uart_cpm_port *port,
+ struct device_node *np)
+{
+ void __iomem *pram;
+ unsigned long offset;
+ struct resource res;
+ unsigned long len;
+
+ /* Don't remap parameter RAM if it has already been initialized
+ * during console setup.
+ */
+ if (IS_SMC(port) && port->smcup)
+ return port->smcup;
+ else if (!IS_SMC(port) && port->sccup)
+ return port->sccup;
+
+ if (of_address_to_resource(np, 1, &res))
+ return NULL;
+
+ len = 1 + res.end - res.start;
+ pram = ioremap(res.start, len);
+ if (!pram)
+ return NULL;
+
+ if (!IS_SMC(port))
+ return pram;
+
+ if (len != 2) {
+ printk(KERN_WARNING "cpm_uart[%d]: device tree references "
+ "SMC pram, using boot loader/wrapper pram mapping. "
+ "Please fix your device tree to reference the pram "
+ "base register instead.\n",
+ port->port.line);
+ return pram;
+ }
+
+ offset = cpm_dpalloc(PROFF_SMC_SIZE, 64);
+ out_be16(pram, offset);
+ iounmap(pram);
+ return cpm_muram_addr(offset);
+}
+
+void cpm_uart_unmap_pram(struct uart_cpm_port *port, void __iomem *pram)
+{
+ if (!IS_SMC(port))
+ iounmap(pram);
+}
+
#else
void cpm_line_cr_cmd(struct uart_cpm_port *port, int cmd)
{
/* Get the UCC number (device ID) */
/* UCCs are numbered 1-7 */
- iprop = of_get_property(np, "device-id", NULL);
- if (!iprop || (*iprop < 1) || (*iprop > UCC_MAX_NUM)) {
- dev_err(&ofdev->dev,
- "missing or invalid UCC specified in device tree\n");
+ iprop = of_get_property(np, "cell-index", NULL);
+ if (!iprop) {
+ iprop = of_get_property(np, "device-id", NULL);
+ if (!iprop) {
+ dev_err(&ofdev->dev, "UCC is unspecified in "
+ "device tree\n");
+ return -EINVAL;
+ }
+ }
+
+ if ((*iprop < 1) || (*iprop > UCC_MAX_NUM)) {
+ dev_err(&ofdev->dev, "no support for UCC%u\n", *iprop);
kfree(qe_port);
return -ENODEV;
}
#include <linux/compiler.h>
#include <linux/types.h>
+/* Opcodes common to CPM1 and CPM2
+*/
+#define CPM_CR_INIT_TRX ((ushort)0x0000)
+#define CPM_CR_INIT_RX ((ushort)0x0001)
+#define CPM_CR_INIT_TX ((ushort)0x0002)
+#define CPM_CR_HUNT_MODE ((ushort)0x0003)
+#define CPM_CR_STOP_TX ((ushort)0x0004)
+#define CPM_CR_GRA_STOP_TX ((ushort)0x0005)
+#define CPM_CR_RESTART_TX ((ushort)0x0006)
+#define CPM_CR_CLOSE_RX_BD ((ushort)0x0007)
+#define CPM_CR_SET_GADDR ((ushort)0x0008)
+#define CPM_CR_SET_TIMER ((ushort)0x0008)
+#define CPM_CR_STOP_IDMA ((ushort)0x000b)
+
/* Buffer descriptors used by many of the CPM protocols. */
typedef struct cpm_buf_desc {
ushort cbd_sc; /* Status and Control */
#define CPM_CR_CHAN ((ushort)0x00f0)
#define CPM_CR_FLG ((ushort)0x0001)
-/* Some commands (there are more...later)
-*/
-#define CPM_CR_INIT_TRX ((ushort)0x0000)
-#define CPM_CR_INIT_RX ((ushort)0x0001)
-#define CPM_CR_INIT_TX ((ushort)0x0002)
-#define CPM_CR_HUNT_MODE ((ushort)0x0003)
-#define CPM_CR_STOP_TX ((ushort)0x0004)
-#define CPM_CR_GRA_STOP_TX ((ushort)0x0005)
-#define CPM_CR_RESTART_TX ((ushort)0x0006)
-#define CPM_CR_CLOSE_RX_BD ((ushort)0x0007)
-#define CPM_CR_SET_GADDR ((ushort)0x0008)
-#define CPM_CR_SET_TIMER CPM_CR_SET_GADDR
-
/* Channel numbers.
*/
#define CPM_CR_CH_SCC1 ((ushort)0x0000)
#define CPM_CR_FCC_PAGE(x) (x + 0x04)
-/* Some opcodes (there are more...later)
+/* CPM2-specific opcodes (see cpm.h for common opcodes)
*/
-#define CPM_CR_INIT_TRX ((ushort)0x0000)
-#define CPM_CR_INIT_RX ((ushort)0x0001)
-#define CPM_CR_INIT_TX ((ushort)0x0002)
-#define CPM_CR_HUNT_MODE ((ushort)0x0003)
-#define CPM_CR_STOP_TX ((ushort)0x0004)
-#define CPM_CR_GRA_STOP_TX ((ushort)0x0005)
-#define CPM_CR_RESTART_TX ((ushort)0x0006)
-#define CPM_CR_SET_GADDR ((ushort)0x0008)
#define CPM_CR_START_IDMA ((ushort)0x0009)
-#define CPM_CR_STOP_IDMA ((ushort)0x000b)
#define mk_cr_cmd(PG, SBC, MCN, OP) \
((PG << 26) | (SBC << 21) | (MCN << 6) | OP)
--- /dev/null
+/* Freescale Local Bus Controller
+ *
+ * Copyright (c) 2006-2007 Freescale Semiconductor
+ *
+ * Authors: Nick Spence <nick.spence@freescale.com>,
+ * Scott Wood <scottwood@freescale.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#ifndef __ASM_FSL_LBC_H
+#define __ASM_FSL_LBC_H
+
+#include <linux/types.h>
+#include <linux/spinlock.h>
+#include <asm/io.h>
+
+struct fsl_lbc_bank {
+ __be32 br; /**< Base Register */
+#define BR_BA 0xFFFF8000
+#define BR_BA_SHIFT 15
+#define BR_PS 0x00001800
+#define BR_PS_SHIFT 11
+#define BR_PS_8 0x00000800 /* Port Size 8 bit */
+#define BR_PS_16 0x00001000 /* Port Size 16 bit */
+#define BR_PS_32 0x00001800 /* Port Size 32 bit */
+#define BR_DECC 0x00000600
+#define BR_DECC_SHIFT 9
+#define BR_DECC_OFF 0x00000000 /* HW ECC checking and generation off */
+#define BR_DECC_CHK 0x00000200 /* HW ECC checking on, generation off */
+#define BR_DECC_CHK_GEN 0x00000400 /* HW ECC checking and generation on */
+#define BR_WP 0x00000100
+#define BR_WP_SHIFT 8
+#define BR_MSEL 0x000000E0
+#define BR_MSEL_SHIFT 5
+#define BR_MS_GPCM 0x00000000 /* GPCM */
+#define BR_MS_FCM 0x00000020 /* FCM */
+#define BR_MS_SDRAM 0x00000060 /* SDRAM */
+#define BR_MS_UPMA 0x00000080 /* UPMA */
+#define BR_MS_UPMB 0x000000A0 /* UPMB */
+#define BR_MS_UPMC 0x000000C0 /* UPMC */
+#define BR_V 0x00000001
+#define BR_V_SHIFT 0
+#define BR_RES ~(BR_BA|BR_PS|BR_DECC|BR_WP|BR_MSEL|BR_V)
+
+ __be32 or; /**< Base Register */
+#define OR0 0x5004
+#define OR1 0x500C
+#define OR2 0x5014
+#define OR3 0x501C
+#define OR4 0x5024
+#define OR5 0x502C
+#define OR6 0x5034
+#define OR7 0x503C
+
+#define OR_FCM_AM 0xFFFF8000
+#define OR_FCM_AM_SHIFT 15
+#define OR_FCM_BCTLD 0x00001000
+#define OR_FCM_BCTLD_SHIFT 12
+#define OR_FCM_PGS 0x00000400
+#define OR_FCM_PGS_SHIFT 10
+#define OR_FCM_CSCT 0x00000200
+#define OR_FCM_CSCT_SHIFT 9
+#define OR_FCM_CST 0x00000100
+#define OR_FCM_CST_SHIFT 8
+#define OR_FCM_CHT 0x00000080
+#define OR_FCM_CHT_SHIFT 7
+#define OR_FCM_SCY 0x00000070
+#define OR_FCM_SCY_SHIFT 4
+#define OR_FCM_SCY_1 0x00000010
+#define OR_FCM_SCY_2 0x00000020
+#define OR_FCM_SCY_3 0x00000030
+#define OR_FCM_SCY_4 0x00000040
+#define OR_FCM_SCY_5 0x00000050
+#define OR_FCM_SCY_6 0x00000060
+#define OR_FCM_SCY_7 0x00000070
+#define OR_FCM_RST 0x00000008
+#define OR_FCM_RST_SHIFT 3
+#define OR_FCM_TRLX 0x00000004
+#define OR_FCM_TRLX_SHIFT 2
+#define OR_FCM_EHTR 0x00000002
+#define OR_FCM_EHTR_SHIFT 1
+};
+
+struct fsl_lbc_regs {
+ struct fsl_lbc_bank bank[8];
+ u8 res0[0x28];
+ __be32 mar; /**< UPM Address Register */
+ u8 res1[0x4];
+ __be32 mamr; /**< UPMA Mode Register */
+#define MxMR_OP_NO (0 << 28) /**< normal operation */
+#define MxMR_OP_WA (1 << 28) /**< write array */
+#define MxMR_OP_RA (2 << 28) /**< read array */
+#define MxMR_OP_RP (3 << 28) /**< run pattern */
+#define MxMR_MAD 0x3f /**< machine address */
+ __be32 mbmr; /**< UPMB Mode Register */
+ __be32 mcmr; /**< UPMC Mode Register */
+ u8 res2[0x8];
+ __be32 mrtpr; /**< Memory Refresh Timer Prescaler Register */
+ __be32 mdr; /**< UPM Data Register */
+ u8 res3[0x4];
+ __be32 lsor; /**< Special Operation Initiation Register */
+ __be32 lsdmr; /**< SDRAM Mode Register */
+ u8 res4[0x8];
+ __be32 lurt; /**< UPM Refresh Timer */
+ __be32 lsrt; /**< SDRAM Refresh Timer */
+ u8 res5[0x8];
+ __be32 ltesr; /**< Transfer Error Status Register */
+#define LTESR_BM 0x80000000
+#define LTESR_FCT 0x40000000
+#define LTESR_PAR 0x20000000
+#define LTESR_WP 0x04000000
+#define LTESR_ATMW 0x00800000
+#define LTESR_ATMR 0x00400000
+#define LTESR_CS 0x00080000
+#define LTESR_CC 0x00000001
+#define LTESR_NAND_MASK (LTESR_FCT | LTESR_PAR | LTESR_CC)
+ __be32 ltedr; /**< Transfer Error Disable Register */
+ __be32 lteir; /**< Transfer Error Interrupt Register */
+ __be32 lteatr; /**< Transfer Error Attributes Register */
+ __be32 ltear; /**< Transfer Error Address Register */
+ u8 res6[0xC];
+ __be32 lbcr; /**< Configuration Register */
+#define LBCR_LDIS 0x80000000
+#define LBCR_LDIS_SHIFT 31
+#define LBCR_BCTLC 0x00C00000
+#define LBCR_BCTLC_SHIFT 22
+#define LBCR_AHD 0x00200000
+#define LBCR_LPBSE 0x00020000
+#define LBCR_LPBSE_SHIFT 17
+#define LBCR_EPAR 0x00010000
+#define LBCR_EPAR_SHIFT 16
+#define LBCR_BMT 0x0000FF00
+#define LBCR_BMT_SHIFT 8
+#define LBCR_INIT 0x00040000
+ __be32 lcrr; /**< Clock Ratio Register */
+#define LCRR_DBYP 0x80000000
+#define LCRR_DBYP_SHIFT 31
+#define LCRR_BUFCMDC 0x30000000
+#define LCRR_BUFCMDC_SHIFT 28
+#define LCRR_ECL 0x03000000
+#define LCRR_ECL_SHIFT 24
+#define LCRR_EADC 0x00030000
+#define LCRR_EADC_SHIFT 16
+#define LCRR_CLKDIV 0x0000000F
+#define LCRR_CLKDIV_SHIFT 0
+ u8 res7[0x8];
+ __be32 fmr; /**< Flash Mode Register */
+#define FMR_CWTO 0x0000F000
+#define FMR_CWTO_SHIFT 12
+#define FMR_BOOT 0x00000800
+#define FMR_ECCM 0x00000100
+#define FMR_AL 0x00000030
+#define FMR_AL_SHIFT 4
+#define FMR_OP 0x00000003
+#define FMR_OP_SHIFT 0
+ __be32 fir; /**< Flash Instruction Register */
+#define FIR_OP0 0xF0000000
+#define FIR_OP0_SHIFT 28
+#define FIR_OP1 0x0F000000
+#define FIR_OP1_SHIFT 24
+#define FIR_OP2 0x00F00000
+#define FIR_OP2_SHIFT 20
+#define FIR_OP3 0x000F0000
+#define FIR_OP3_SHIFT 16
+#define FIR_OP4 0x0000F000
+#define FIR_OP4_SHIFT 12
+#define FIR_OP5 0x00000F00
+#define FIR_OP5_SHIFT 8
+#define FIR_OP6 0x000000F0
+#define FIR_OP6_SHIFT 4
+#define FIR_OP7 0x0000000F
+#define FIR_OP7_SHIFT 0
+#define FIR_OP_NOP 0x0 /* No operation and end of sequence */
+#define FIR_OP_CA 0x1 /* Issue current column address */
+#define FIR_OP_PA 0x2 /* Issue current block+page address */
+#define FIR_OP_UA 0x3 /* Issue user defined address */
+#define FIR_OP_CM0 0x4 /* Issue command from FCR[CMD0] */
+#define FIR_OP_CM1 0x5 /* Issue command from FCR[CMD1] */
+#define FIR_OP_CM2 0x6 /* Issue command from FCR[CMD2] */
+#define FIR_OP_CM3 0x7 /* Issue command from FCR[CMD3] */
+#define FIR_OP_WB 0x8 /* Write FBCR bytes from FCM buffer */
+#define FIR_OP_WS 0x9 /* Write 1 or 2 bytes from MDR[AS] */
+#define FIR_OP_RB 0xA /* Read FBCR bytes to FCM buffer */
+#define FIR_OP_RS 0xB /* Read 1 or 2 bytes to MDR[AS] */
+#define FIR_OP_CW0 0xC /* Wait then issue FCR[CMD0] */
+#define FIR_OP_CW1 0xD /* Wait then issue FCR[CMD1] */
+#define FIR_OP_RBW 0xE /* Wait then read FBCR bytes */
+#define FIR_OP_RSW 0xE /* Wait then read 1 or 2 bytes */
+ __be32 fcr; /**< Flash Command Register */
+#define FCR_CMD0 0xFF000000
+#define FCR_CMD0_SHIFT 24
+#define FCR_CMD1 0x00FF0000
+#define FCR_CMD1_SHIFT 16
+#define FCR_CMD2 0x0000FF00
+#define FCR_CMD2_SHIFT 8
+#define FCR_CMD3 0x000000FF
+#define FCR_CMD3_SHIFT 0
+ __be32 fbar; /**< Flash Block Address Register */
+#define FBAR_BLK 0x00FFFFFF
+ __be32 fpar; /**< Flash Page Address Register */
+#define FPAR_SP_PI 0x00007C00
+#define FPAR_SP_PI_SHIFT 10
+#define FPAR_SP_MS 0x00000200
+#define FPAR_SP_CI 0x000001FF
+#define FPAR_SP_CI_SHIFT 0
+#define FPAR_LP_PI 0x0003F000
+#define FPAR_LP_PI_SHIFT 12
+#define FPAR_LP_MS 0x00000800
+#define FPAR_LP_CI 0x000007FF
+#define FPAR_LP_CI_SHIFT 0
+ __be32 fbcr; /**< Flash Byte Count Register */
+#define FBCR_BC 0x00000FFF
+ u8 res11[0x8];
+ u8 res8[0xF00];
+};
+
+extern struct fsl_lbc_regs __iomem *fsl_lbc_regs;
+extern spinlock_t fsl_lbc_lock;
+
+/*
+ * FSL UPM routines
+ */
+struct fsl_upm {
+ __be32 __iomem *mxmr;
+ int width;
+};
+
+extern int fsl_lbc_find(phys_addr_t addr_base);
+extern int fsl_upm_find(phys_addr_t addr_base, struct fsl_upm *upm);
+
+/**
+ * fsl_upm_start_pattern - start UPM patterns execution
+ * @upm: pointer to the fsl_upm structure obtained via fsl_upm_find
+ * @pat_offset: UPM pattern offset for the command to be executed
+ *
+ * This routine programmes UPM so the next memory access that hits an UPM
+ * will trigger pattern execution, starting at pat_offset.
+ */
+static inline void fsl_upm_start_pattern(struct fsl_upm *upm, u8 pat_offset)
+{
+ clrsetbits_be32(upm->mxmr, MxMR_MAD, MxMR_OP_RP | pat_offset);
+}
+
+/**
+ * fsl_upm_end_pattern - end UPM patterns execution
+ * @upm: pointer to the fsl_upm structure obtained via fsl_upm_find
+ *
+ * This routine reverts UPM to normal operation mode.
+ */
+static inline void fsl_upm_end_pattern(struct fsl_upm *upm)
+{
+ clrbits32(upm->mxmr, MxMR_OP_RP);
+
+ while (in_be32(upm->mxmr) & MxMR_OP_RP)
+ cpu_relax();
+}
+
+/**
+ * fsl_upm_run_pattern - actually run an UPM pattern
+ * @upm: pointer to the fsl_upm structure obtained via fsl_upm_find
+ * @io_base: remapped pointer to where memory access should happen
+ * @mar: MAR register content during pattern execution
+ *
+ * This function triggers dummy write to the memory specified by the io_base,
+ * thus UPM pattern actually executed. Note that mar usage depends on the
+ * pre-programmed AMX bits in the UPM RAM.
+ */
+static inline int fsl_upm_run_pattern(struct fsl_upm *upm,
+ void __iomem *io_base, u32 mar)
+{
+ int ret = 0;
+ unsigned long flags;
+
+ spin_lock_irqsave(&fsl_lbc_lock, flags);
+
+ out_be32(&fsl_lbc_regs->mar, mar << (32 - upm->width));
+
+ switch (upm->width) {
+ case 8:
+ out_8(io_base, 0x0);
+ break;
+ case 16:
+ out_be16(io_base, 0x0);
+ break;
+ case 32:
+ out_be32(io_base, 0x0);
+ break;
+ default:
+ ret = -EINVAL;
+ break;
+ }
+
+ spin_unlock_irqrestore(&fsl_lbc_lock, flags);
+
+ return ret;
+}
+
+#endif /* __ASM_FSL_LBC_H */
#ifdef __KERNEL__
#include <linux/kernel.h>
+#include <asm/io.h>
#define QE_IMMAP_SIZE (1024 * 1024) /* 1MB from 1MB+IMMR */
u8 res18[0xC0000]; /* 0x140000 - 0x200000 */
} __attribute__ ((packed));
-extern struct qe_immap *qe_immr;
+extern struct qe_immap __iomem *qe_immr;
extern phys_addr_t get_qe_base(void);
static inline unsigned long immrbar_virt_to_phys(void *address)
/* QE internal API */
int qe_issue_cmd(u32 cmd, u32 device, u8 mcn_protocol, u32 cmd_input);
enum qe_clock qe_clock_source(const char *source);
+unsigned int qe_get_brg_clk(void);
int qe_setbrg(enum qe_clock brg, unsigned int rate, unsigned int multiplier);
int qe_get_snum(void);
void qe_put_snum(u8 snum);
int qe_muram_free(unsigned long offset);
unsigned long qe_muram_alloc_fixed(unsigned long offset, int size);
void qe_muram_dump(void);
-void *qe_muram_addr(unsigned long offset);
+
+static inline void __iomem *qe_muram_addr(unsigned long offset)
+{
+ return (void __iomem *)&qe_immr->muram[offset];
+}
+
+static inline unsigned long qe_muram_offset(void __iomem *addr)
+{
+ return addr - (void __iomem *)qe_immr->muram;
+}
/* Structure that defines QE firmware binary files.
*
projects / linux-2.6 / commitdiff