]> err.no Git - linux-2.6/commitdiff
V4L/DVB (7573): mt312: Supports different xtal frequencies
authorMatthias Schwarzott <zzam@gentoo.org>
Sat, 12 Apr 2008 18:04:48 +0000 (15:04 -0300)
committerMauro Carvalho Chehab <mchehab@infradead.org>
Thu, 24 Apr 2008 17:09:40 +0000 (14:09 -0300)
Do not hardcode xtal frequency but allow different values
for future zl10313 support.

Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
drivers/media/dvb/frontends/mt312.c

index 32b419477887f213c7272d66339dd93bcc46336e..1f478c8c0d4a10c5a537da0f72b27b3dde84f47a 100644 (file)
@@ -43,7 +43,8 @@ struct mt312_state {
        struct dvb_frontend frontend;
 
        u8 id;
-       u8 frequency;
+       unsigned long xtal;
+       u8 freq_mult;
 };
 
 static int debug;
@@ -53,8 +54,6 @@ static int debug;
                        printk(KERN_DEBUG "mt312: " args); \
        } while (0)
 
-#define MT312_SYS_CLK          90000000UL      /* 90 MHz */
-#define MT312_LPOWER_SYS_CLK   60000000UL      /* 60 MHz */
 #define MT312_PLL_CLK          10000000UL      /* 10 MHz */
 
 static int mt312_read(struct mt312_state *state, const enum mt312_reg_addr reg,
@@ -209,7 +208,7 @@ static int mt312_get_symbol_rate(struct mt312_state *state, u32 *sr)
                dprintk("sym_rat_op=%d dec_ratio=%d\n",
                       sym_rat_op, dec_ratio);
                dprintk("*sr(manual) = %lu\n",
-                      (((MT312_PLL_CLK * 8192) / (sym_rat_op + 8192)) *
+                      (((state->xtal * 8192) / (sym_rat_op + 8192)) *
                        2) - dec_ratio);
        }
 
@@ -242,7 +241,7 @@ static int mt312_initfe(struct dvb_frontend *fe)
 
        /* wake up */
        ret = mt312_writereg(state, CONFIG,
-                       (state->frequency == 60 ? 0x88 : 0x8c));
+                       (state->freq_mult == 6 ? 0x88 : 0x8c));
        if (ret < 0)
                return ret;
 
@@ -266,11 +265,10 @@ static int mt312_initfe(struct dvb_frontend *fe)
        }
 
        /* SYS_CLK */
-       buf[0] = mt312_div((state->frequency == 60 ? MT312_LPOWER_SYS_CLK :
-                               MT312_SYS_CLK) * 2, 1000000);
+       buf[0] = mt312_div(state->xtal * state->freq_mult * 2, 1000000);
 
        /* DISEQC_RATIO */
-       buf[1] = mt312_div(MT312_PLL_CLK, 22000 * 4);
+       buf[1] = mt312_div(state->xtal, 22000 * 4);
 
        ret = mt312_write(state, SYS_CLK, buf, sizeof(buf));
        if (ret < 0)
@@ -535,17 +533,17 @@ static int mt312_set_frontend(struct dvb_frontend *fe,
                        return ret;
                if (p->u.qpsk.symbol_rate >= 30000000) {
                        /* Note that 30MS/s should use 90MHz */
-                       if ((config_val & 0x0c) == 0x08) {
+                       if (state->freq_mult == 6) {
                                /* We are running 60MHz */
-                               state->frequency = 90;
+                               state->freq_mult = 9;
                                ret = mt312_initfe(fe);
                                if (ret < 0)
                                        return ret;
                        }
                } else {
-                       if ((config_val & 0x0c) == 0x0C) {
+                       if (state->freq_mult == 9) {
                                /* We are running 90MHz */
-                               state->frequency = 60;
+                               state->freq_mult = 6;
                                ret = mt312_initfe(fe);
                                if (ret < 0)
                                        return ret;
@@ -664,6 +662,7 @@ static void mt312_release(struct dvb_frontend *fe)
        kfree(state);
 }
 
+#define MT312_SYS_CLK          90000000UL      /* 90 MHz */
 static struct dvb_frontend_ops vp310_mt312_ops = {
 
        .info = {
@@ -671,8 +670,8 @@ static struct dvb_frontend_ops vp310_mt312_ops = {
                .type = FE_QPSK,
                .frequency_min = 950000,
                .frequency_max = 2150000,
-               .frequency_stepsize = (MT312_PLL_CLK / 1000) / 128,
-               .symbol_rate_min = MT312_SYS_CLK / 128,
+               .frequency_stepsize = (MT312_PLL_CLK / 1000) / 128, /* FIXME: adjust freq to real used xtal */
+               .symbol_rate_min = MT312_SYS_CLK / 128, /* FIXME as above */
                .symbol_rate_max = MT312_SYS_CLK / 2,
                .caps =
                    FE_CAN_FEC_1_2 | FE_CAN_FEC_2_3 |
@@ -729,11 +728,13 @@ struct dvb_frontend *vp310_mt312_attach(const struct mt312_config *config,
        switch (state->id) {
        case ID_VP310:
                strcpy(state->frontend.ops.info.name, "Zarlink VP310 DVB-S");
-               state->frequency = 90;
+               state->xtal = MT312_PLL_CLK;
+               state->freq_mult = 9;
                break;
        case ID_MT312:
                strcpy(state->frontend.ops.info.name, "Zarlink MT312 DVB-S");
-               state->frequency = 60;
+               state->xtal = MT312_PLL_CLK;
+               state->freq_mult = 6;
                break;
        default:
                printk(KERN_WARNING "Only Zarlink VP310/MT312"