#define AR5K_CR_TXD0 0x00000008 /* TX Disable for queue 0 on 5210 */
#define AR5K_CR_TXD1 0x00000010 /* TX Disable for queue 1 on 5210 */
#define AR5K_CR_RXD 0x00000020 /* RX Disable */
-#define AR5K_CR_SWI 0x00000040
+#define AR5K_CR_SWI 0x00000040 /* Software Interrupt */
/*
* RX Descriptor Pointer register
*/
#define AR5K_CFG 0x0014 /* Register Address */
#define AR5K_CFG_SWTD 0x00000001 /* Byte-swap TX descriptor (for big endian archs) */
-#define AR5K_CFG_SWTB 0x00000002 /* Byte-swap TX buffer (?) */
+#define AR5K_CFG_SWTB 0x00000002 /* Byte-swap TX buffer */
#define AR5K_CFG_SWRD 0x00000004 /* Byte-swap RX descriptor */
-#define AR5K_CFG_SWRB 0x00000008 /* Byte-swap RX buffer (?) */
-#define AR5K_CFG_SWRG 0x00000010 /* Byte-swap Register values (?) */
-#define AR5K_CFG_ADHOC 0x00000020 /* [5211+] */
+#define AR5K_CFG_SWRB 0x00000008 /* Byte-swap RX buffer */
+#define AR5K_CFG_SWRG 0x00000010 /* Byte-swap Register access */
+#define AR5K_CFG_ADHOC 0x00000020 /* AP/Adhoc indication [5211+] */
#define AR5K_CFG_PHY_OK 0x00000100 /* [5211+] */
#define AR5K_CFG_EEBS 0x00000200 /* EEPROM is busy */
-#define AR5K_CFG_CLKGD 0x00000400 /* Clock gated (?) */
+#define AR5K_CFG_CLKGD 0x00000400 /* Clock gated (Disable dynamic clock) */
#define AR5K_CFG_TXCNT 0x00007800 /* Tx frame count (?) [5210] */
#define AR5K_CFG_TXCNT_S 11
#define AR5K_CFG_TXFSTAT 0x00008000 /* Tx frame status (?) [5210] */
#define AR5K_CFG_TXFSTRT 0x00010000 /* [5210] */
-#define AR5K_CFG_PCI_THRES 0x00060000 /* [5211+] */
+#define AR5K_CFG_PCI_THRES 0x00060000 /* PCI Master req q threshold [5211+] */
#define AR5K_CFG_PCI_THRES_S 17
/*
/*
* Transmit configuration register
*/
-#define AR5K_TXCFG 0x0030 /* Register Address */
-#define AR5K_TXCFG_SDMAMR 0x00000007 /* DMA size */
-#define AR5K_TXCFG_SDMAMR_S 0
-#define AR5K_TXCFG_B_MODE 0x00000008 /* Set b mode for 5111 (enable 2111) */
-#define AR5K_TXCFG_TXFSTP 0x00000008 /* TX DMA full Stop [5210] */
-#define AR5K_TXCFG_TXFULL 0x000003f0 /* TX Triger level mask */
-#define AR5K_TXCFG_TXFULL_S 4
-#define AR5K_TXCFG_TXFULL_0B 0x00000000
-#define AR5K_TXCFG_TXFULL_64B 0x00000010
-#define AR5K_TXCFG_TXFULL_128B 0x00000020
-#define AR5K_TXCFG_TXFULL_192B 0x00000030
-#define AR5K_TXCFG_TXFULL_256B 0x00000040
-#define AR5K_TXCFG_TXCONT_EN 0x00000080
-#define AR5K_TXCFG_DMASIZE 0x00000100 /* Flag for passing DMA size [5210] */
-#define AR5K_TXCFG_JUMBO_TXE 0x00000400 /* Enable jumbo frames transmition (?) [5211+] */
-#define AR5K_TXCFG_RTSRND 0x00001000 /* [5211+] */
-#define AR5K_TXCFG_FRMPAD_DIS 0x00002000 /* [5211+] */
-#define AR5K_TXCFG_RDY_DIS 0x00004000 /* [5211+] */
+#define AR5K_TXCFG 0x0030 /* Register Address */
+#define AR5K_TXCFG_SDMAMR 0x00000007 /* DMA size (read) */
+#define AR5K_TXCFG_SDMAMR_S 0
+#define AR5K_TXCFG_B_MODE 0x00000008 /* Set b mode for 5111 (enable 2111) */
+#define AR5K_TXCFG_TXFSTP 0x00000008 /* TX DMA full Stop [5210] */
+#define AR5K_TXCFG_TXFULL 0x000003f0 /* TX Triger level mask */
+#define AR5K_TXCFG_TXFULL_S 4
+#define AR5K_TXCFG_TXFULL_0B 0x00000000
+#define AR5K_TXCFG_TXFULL_64B 0x00000010
+#define AR5K_TXCFG_TXFULL_128B 0x00000020
+#define AR5K_TXCFG_TXFULL_192B 0x00000030
+#define AR5K_TXCFG_TXFULL_256B 0x00000040
+#define AR5K_TXCFG_TXCONT_EN 0x00000080
+#define AR5K_TXCFG_DMASIZE 0x00000100 /* Flag for passing DMA size [5210] */
+#define AR5K_TXCFG_JUMBO_DESC_EN 0x00000400 /* Enable jumbo tx descriptors [5211+] */
+#define AR5K_TXCFG_ADHOC_BCN_ATIM 0x00000800 /* Adhoc Beacon ATIM Policy */
+#define AR5K_TXCFG_ATIM_WINDOW_DEF_DIS 0x00001000 /* Disable ATIM window defer [5211+] */
+#define AR5K_TXCFG_RTSRND 0x00001000 /* [5211+] */
+#define AR5K_TXCFG_FRMPAD_DIS 0x00002000 /* [5211+] */
+#define AR5K_TXCFG_RDY_CBR_DIS 0x00004000 /* Ready time CBR disable [5211+] */
+#define AR5K_TXCFG_JUMBO_FRM_MODE 0x00008000 /* Jumbo frame mode [5211+] */
+#define AR5K_TXCFG_DCU_CACHING_DIS 0x00010000 /* Disable DCU caching */
/*
* Receive configuration register
*/
#define AR5K_RXCFG 0x0034 /* Register Address */
-#define AR5K_RXCFG_SDMAMW 0x00000007 /* DMA size */
+#define AR5K_RXCFG_SDMAMW 0x00000007 /* DMA size (write) */
#define AR5K_RXCFG_SDMAMW_S 0
-#define AR5K_RXCFG_DEF_ANTENNA 0x00000008 /* Default antenna */
-#define AR5K_RXCFG_ZLFDMA 0x00000010 /* Zero-length DMA */
-#define AR5K_RXCFG_JUMBO_RXE 0x00000020 /* Enable jumbo frames reception (?) [5211+] */
-#define AR5K_RXCFG_JUMBO_WRAP 0x00000040 /* Wrap jumbo frames (?) [5211+] */
+#define AR5K_RXCFG_ZLFDMA 0x00000008 /* Enable Zero-length frame DMA */
+#define AR5K_RXCFG_DEF_ANTENNA 0x00000010 /* Default antenna (?) */
+#define AR5K_RXCFG_JUMBO_RXE 0x00000020 /* Enable jumbo rx descriptors [5211+] */
+#define AR5K_RXCFG_JUMBO_WRAP 0x00000040 /* Wrap jumbo frames [5211+] */
+#define AR5K_RXCFG_SLE_ENTRY 0x00000080 /* Sleep entry policy */
/*
* Receive jumbo descriptor last address register
* MIB control register
*/
#define AR5K_MIBC 0x0040 /* Register Address */
-#define AR5K_MIBC_COW 0x00000001
-#define AR5K_MIBC_FMC 0x00000002 /* Freeze Mib Counters (?) */
-#define AR5K_MIBC_CMC 0x00000004 /* Clean Mib Counters (?) */
-#define AR5K_MIBC_MCS 0x00000008
+#define AR5K_MIBC_COW 0x00000001 /* Warn test indicator */
+#define AR5K_MIBC_FMC 0x00000002 /* Freeze MIB Counters */
+#define AR5K_MIBC_CMC 0x00000004 /* Clean MIB Counters */
+#define AR5K_MIBC_MCS 0x00000008 /* MIB counter strobe */
/*
* Timeout prescale register
*/
#define AR5K_TOPS 0x0044
-#define AR5K_TOPS_M 0x0000ffff /* [5211+] (?) */
+#define AR5K_TOPS_M 0x0000ffff
/*
* Receive timeout register (no frame received)
*/
#define AR5K_RXNOFRM 0x0048
-#define AR5K_RXNOFRM_M 0x000003ff /* [5211+] (?) */
+#define AR5K_RXNOFRM_M 0x000003ff
/*
* Transmit timeout register (no frame sent)
*/
#define AR5K_TXNOFRM 0x004c
-#define AR5K_TXNOFRM_M 0x000003ff /* [5211+] (?) */
-#define AR5K_TXNOFRM_QCU 0x000ffc00 /* [5211+] (?) */
+#define AR5K_TXNOFRM_M 0x000003ff
+#define AR5K_TXNOFRM_QCU 0x000ffc00
/*
* Receive frame gap timeout register
*/
#define AR5K_RPGTO 0x0050
-#define AR5K_RPGTO_M 0x000003ff /* [5211+] (?) */
+#define AR5K_RPGTO_M 0x000003ff
/*
* Receive frame count limit register
/*
* Misc settings register
+ * (reserved0-3)
*/
#define AR5K_MISC 0x0058 /* Register Address */
#define AR5K_MISC_DMA_OBS_M 0x000001e0
/*
* QCU/DCU clock gating register (5311)
+ * (reserved4-5)
*/
#define AR5K_QCUDCU_CLKGT 0x005c /* Register Address (?) */
#define AR5K_QCUDCU_CLKGT_QCU 0x0000ffff /* Mask for QCU clock */
#define AR5K_ISR_TXEOL 0x00000400 /* Empty TX descriptor */
#define AR5K_ISR_TXURN 0x00000800 /* Transmit FIFO underrun */
#define AR5K_ISR_MIB 0x00001000 /* Update MIB counters */
-#define AR5K_ISR_SWI 0x00002000 /* Software interrupt (?) */
+#define AR5K_ISR_SWI 0x00002000 /* Software interrupt */
#define AR5K_ISR_RXPHY 0x00004000 /* PHY error */
-#define AR5K_ISR_RXKCM 0x00008000
+#define AR5K_ISR_RXKCM 0x00008000 /* RX Key cache miss */
#define AR5K_ISR_SWBA 0x00010000 /* Software beacon alert */
#define AR5K_ISR_BRSSI 0x00020000
#define AR5K_ISR_BMISS 0x00040000 /* Beacon missed */
#define AR5K_ISR_HIUERR 0x00080000 /* Host Interface Unit error [5211+] */
#define AR5K_ISR_BNR 0x00100000 /* Beacon not ready [5211+] */
-#define AR5K_ISR_MCABT 0x00100000 /* [5210] */
-#define AR5K_ISR_RXCHIRP 0x00200000 /* [5212+] */
-#define AR5K_ISR_SSERR 0x00200000 /* [5210] */
-#define AR5K_ISR_DPERR 0x00400000 /* [5210] */
+#define AR5K_ISR_MCABT 0x00100000 /* Master Cycle Abort [5210] */
+#define AR5K_ISR_RXCHIRP 0x00200000 /* CHIRP Received [5212+] */
+#define AR5K_ISR_SSERR 0x00200000 /* Signaled System Error [5210] */
+#define AR5K_ISR_DPERR 0x00400000 /* Det par Error (?) [5210] */
#define AR5K_ISR_TIM 0x00800000 /* [5210] */
#define AR5K_ISR_BCNMISC 0x00800000 /* [5212+] */
#define AR5K_ISR_GPIO 0x01000000 /* GPIO (rf kill)*/
#define AR5K_SISR2 0x008c /* Register Address [5211+] */
#define AR5K_SISR2_QCU_TXURN 0x000003ff /* Mask for QCU_TXURN */
-#define AR5K_SISR2_MCABT 0x00100000
-#define AR5K_SISR2_SSERR 0x00200000
-#define AR5K_SISR2_DPERR 0x00400000
+#define AR5K_SISR2_MCABT 0x00100000 /* Master Cycle Abort */
+#define AR5K_SISR2_SSERR 0x00200000 /* Signaled System Error */
+#define AR5K_SISR2_DPERR 0x00400000 /* Det par Error (?) */
#define AR5K_SISR2_TIM 0x01000000 /* [5212+] */
#define AR5K_SISR2_CAB_END 0x02000000 /* [5212+] */
-#define AR5K_SISR2_DTIM_SYNC 0x04000000 /* [5212+] */
-#define AR5K_SISR2_BCN_TIMEOUT 0x08000000 /* [5212+] */
-#define AR5K_SISR2_CAB_TIMEOUT 0x10000000 /* [5212+] */
+#define AR5K_SISR2_DTIM_SYNC 0x04000000 /* DTIM sync lost [5212+] */
+#define AR5K_SISR2_BCN_TIMEOUT 0x08000000 /* Beacon Timeout [5212+] */
+#define AR5K_SISR2_CAB_TIMEOUT 0x10000000 /* CAB Timeout [5212+] */
#define AR5K_SISR2_DTIM 0x20000000 /* [5212+] */
#define AR5K_SISR3 0x0090 /* Register Address [5211+] */
#define AR5K_IMR_TXEOL 0x00000400 /* Empty TX descriptor*/
#define AR5K_IMR_TXURN 0x00000800 /* Transmit FIFO underrun*/
#define AR5K_IMR_MIB 0x00001000 /* Update MIB counters*/
-#define AR5K_IMR_SWI 0x00002000
+#define AR5K_IMR_SWI 0x00002000 /* Software interrupt */
#define AR5K_IMR_RXPHY 0x00004000 /* PHY error*/
-#define AR5K_IMR_RXKCM 0x00008000
+#define AR5K_IMR_RXKCM 0x00008000 /* RX Key cache miss */
#define AR5K_IMR_SWBA 0x00010000 /* Software beacon alert*/
#define AR5K_IMR_BRSSI 0x00020000
#define AR5K_IMR_BMISS 0x00040000 /* Beacon missed*/
#define AR5K_IMR_HIUERR 0x00080000 /* Host Interface Unit error [5211+] */
#define AR5K_IMR_BNR 0x00100000 /* Beacon not ready [5211+] */
-#define AR5K_IMR_MCABT 0x00100000 /* [5210] */
-#define AR5K_IMR_RXCHIRP 0x00200000 /* [5212+]*/
-#define AR5K_IMR_SSERR 0x00200000 /* [5210] */
-#define AR5K_IMR_DPERR 0x00400000 /* [5210] */
+#define AR5K_IMR_MCABT 0x00100000 /* Master Cycle Abort [5210] */
+#define AR5K_IMR_RXCHIRP 0x00200000 /* CHIRP Received [5212+]*/
+#define AR5K_IMR_SSERR 0x00200000 /* Signaled System Error [5210] */
+#define AR5K_IMR_DPERR 0x00400000 /* Det par Error (?) [5210] */
#define AR5K_IMR_TIM 0x00800000 /* [5211+] */
#define AR5K_IMR_BCNMISC 0x00800000 /* [5212+] */
#define AR5K_IMR_GPIO 0x01000000 /* GPIO (rf kill)*/
#define AR5K_SIMR2 0x00ac /* Register Address [5211+] */
#define AR5K_SIMR2_QCU_TXURN 0x000003ff /* Mask for QCU_TXURN */
#define AR5K_SIMR2_QCU_TXURN_S 0
-#define AR5K_SIMR2_MCABT 0x00100000
-#define AR5K_SIMR2_SSERR 0x00200000
-#define AR5K_SIMR2_DPERR 0x00400000
+#define AR5K_SIMR2_MCABT 0x00100000 /* Master Cycle Abort */
+#define AR5K_SIMR2_SSERR 0x00200000 /* Signaled System Error */
+#define AR5K_SIMR2_DPERR 0x00400000 /* Det par Error (?) */
#define AR5K_SIMR2_TIM 0x01000000 /* [5212+] */
#define AR5K_SIMR2_CAB_END 0x02000000 /* [5212+] */
-#define AR5K_SIMR2_DTIM_SYNC 0x04000000 /* [5212+] */
-#define AR5K_SIMR2_BCN_TIMEOUT 0x08000000 /* [5212+] */
-#define AR5K_SIMR2_CAB_TIMEOUT 0x10000000 /* [5212+] */
+#define AR5K_SIMR2_DTIM_SYNC 0x04000000 /* DTIM Sync lost [5212+] */
+#define AR5K_SIMR2_BCN_TIMEOUT 0x08000000 /* Beacon Timeout [5212+] */
+#define AR5K_SIMR2_CAB_TIMEOUT 0x10000000 /* CAB Timeout [5212+] */
#define AR5K_SIMR2_DTIM 0x20000000 /* [5212+] */
#define AR5K_SIMR3 0x00b0 /* Register Address [5211+] */
#define AR5K_SIMR4_QTRIG 0x000003ff /* Mask for QTRIG */
#define AR5K_SIMR4_QTRIG_S 0
+/*
+ * DMA Debug registers 0-7
+ * 0xe0 - 0xfc
+ */
/*
* Decompression mask registers [5212+]
*/
-#define AR5K_DCM_ADDR 0x0400 /*Decompression mask address (?)*/
-#define AR5K_DCM_DATA 0x0404 /*Decompression mask data (?)*/
+#define AR5K_DCM_ADDR 0x0400 /*Decompression mask address (index) */
+#define AR5K_DCM_DATA 0x0404 /*Decompression mask data */
+
+/*
+ * Wake On Wireless pattern control register [5212+]
+ */
+#define AR5K_WOW_PCFG 0x0410 /* Register Address */
+#define AR5K_WOW_PCFG_PAT_MATCH_EN 0x00000001 /* Pattern match enable */
+#define AR5K_WOW_PCFG_LONG_FRAME_POL 0x00000002 /* Long frame policy */
+#define AR5K_WOW_PCFG_WOBMISS 0x00000004 /* Wake on bea(con) miss (?) */
+#define AR5K_WOW_PCFG_PAT_0_EN 0x00000100 /* Enable pattern 0 */
+#define AR5K_WOW_PCFG_PAT_1_EN 0x00000200 /* Enable pattern 1 */
+#define AR5K_WOW_PCFG_PAT_2_EN 0x00000400 /* Enable pattern 2 */
+#define AR5K_WOW_PCFG_PAT_3_EN 0x00000800 /* Enable pattern 3 */
+#define AR5K_WOW_PCFG_PAT_4_EN 0x00001000 /* Enable pattern 4 */
+#define AR5K_WOW_PCFG_PAT_5_EN 0x00002000 /* Enable pattern 5 */
+
+/*
+ * Wake On Wireless pattern index register (?) [5212+]
+ */
+#define AR5K_WOW_PAT_IDX 0x0414
+
+/*
+ * Wake On Wireless pattern data register [5212+]
+ */
+#define AR5K_WOW_PAT_DATA 0x0418 /* Register Address */
+#define AR5K_WOW_PAT_DATA_0_3_V 0x00000001 /* Pattern 0, 3 value */
+#define AR5K_WOW_PAT_DATA_1_4_V 0x00000100 /* Pattern 1, 4 value */
+#define AR5K_WOW_PAT_DATA_2_5_V 0x00010000 /* Pattern 2, 5 value */
+#define AR5K_WOW_PAT_DATA_0_3_M 0x01000000 /* Pattern 0, 3 mask */
+#define AR5K_WOW_PAT_DATA_1_4_M 0x04000000 /* Pattern 1, 4 mask */
+#define AR5K_WOW_PAT_DATA_2_5_M 0x10000000 /* Pattern 2, 5 mask */
/*
* Decompression configuration registers [5212+]
*/
-#define AR5K_DCCFG 0x0420
+#define AR5K_DCCFG 0x0420 /* Register Address */
+#define AR5K_DCCFG_GLOBAL_EN 0x00000001 /* Enable decompression on all queues */
+#define AR5K_DCCFG_BYPASS_EN 0x00000002 /* Bypass decompression */
+#define AR5K_DCCFG_BCAST_EN 0x00000004 /* Enable decompression for bcast frames */
+#define AR5K_DCCFG_MCAST_EN 0x00000008 /* Enable decompression for mcast frames */
/*
* Compression configuration registers [5212+]
*/
-#define AR5K_CCFG 0x0600
-#define AR5K_CCFG_CUP 0x0604
+#define AR5K_CCFG 0x0600 /* Register Address */
+#define AR5K_CCFG_WINDOW_SIZE 0x00000007 /* Compression window size */
+#define AR5K_CCFG_CPC_EN 0x00000008 /* Enable performance counters */
+
+#define AR5K_CCFG_CCU 0x0604 /* Register Address */
+#define AR5K_CCFG_CCU_CUP_EN 0x00000001 /* CCU Catchup enable */
+#define AR5K_CCFG_CCU_CREDIT 0x00000002 /* CCU Credit (field) */
+#define AR5K_CCFG_CCU_CD_THRES 0x00000080 /* CCU Cyc(lic?) debt threshold (field) */
+#define AR5K_CCFG_CCU_CUP_LCNT 0x00010000 /* CCU Catchup lit(?) count */
+#define AR5K_CCFG_CCU_INIT 0x00100200 /* Initial value during reset */
/*
* Compression performance counter registers [5212+]
#define AR5K_CPC1 0x0614 /* Compression performance counter 1*/
#define AR5K_CPC2 0x0618 /* Compression performance counter 2 */
#define AR5K_CPC3 0x061c /* Compression performance counter 3 */
-#define AR5K_CPCORN 0x0620 /* Compression performance overrun (?) */
+#define AR5K_CPCOVF 0x0620 /* Compression performance overflow */
/*
* set/clear, which contain status for all queues (we shift by 1 for each
* queue). To access these registers easily we define some macros here
* that are used inside HAL. For more infos check out *_tx_queue functs.
- *
- * TODO: Boundary checking on macros (here?)
*/
/*
#define AR5K_QCU_RDYTIMECFG_BASE 0x0900 /* Register Address - Queue0 RDYTIMECFG */
#define AR5K_QCU_RDYTIMECFG_INTVAL 0x00ffffff /* Ready time interval mask */
#define AR5K_QCU_RDYTIMECFG_INTVAL_S 0
-#define AR5K_QCU_RDYTIMECFG_DURATION 0x00ffffff /* Ready time duration mask */
#define AR5K_QCU_RDYTIMECFG_ENABLE 0x01000000 /* Ready time enable mask */
#define AR5K_QUEUE_RDYTIMECFG(_q) AR5K_QUEUE_REG(AR5K_QCU_RDYTIMECFG_BASE, _q)
*/
#define AR5K_QCU_MISC_BASE 0x09c0 /* Register Address -Queue0 MISC */
#define AR5K_QCU_MISC_FRSHED_M 0x0000000f /* Frame sheduling mask */
-#define AR5K_QCU_MISC_FRSHED_ASAP 0 /* ASAP */
-#define AR5K_QCU_MISC_FRSHED_CBR 1 /* Constant Bit Rate */
-#define AR5K_QCU_MISC_FRSHED_DBA_GT 2 /* DMA Beacon alert gated (?) */
-#define AR5K_QCU_MISC_FRSHED_TIM_GT 3 /* Time gated (?) */
+#define AR5K_QCU_MISC_FRSHED_ASAP 0 /* ASAP */
+#define AR5K_QCU_MISC_FRSHED_CBR 1 /* Constant Bit Rate */
+#define AR5K_QCU_MISC_FRSHED_DBA_GT 2 /* DMA Beacon alert gated (?) */
+#define AR5K_QCU_MISC_FRSHED_TIM_GT 3 /* Time gated (?) */
#define AR5K_QCU_MISC_FRSHED_BCN_SENT_GT 4 /* Beacon sent gated (?) */
#define AR5K_QCU_MISC_ONESHOT_ENABLE 0x00000010 /* Oneshot enable */
#define AR5K_QCU_MISC_CBREXP 0x00000020 /* CBR expired (normal queue) */
#define AR5K_QCU_MISC_CBREXP_BCN 0x00000040 /* CBR expired (beacon queue) */
-#define AR5K_QCU_MISC_BCN_ENABLE 0x00000080 /* Beacons enabled */
-#define AR5K_QCU_MISC_CBR_THRES_ENABLE 0x00000100 /* CBR threshold enabled (?) */
-#define AR5K_QCU_MISC_TXE 0x00000200 /* TXE reset when RDYTIME enalbed (?) */
-#define AR5K_QCU_MISC_CBR 0x00000400 /* CBR threshold reset (?) */
-#define AR5K_QCU_MISC_DCU_EARLY 0x00000800 /* DCU reset (?) */
+#define AR5K_QCU_MISC_BCN_ENABLE 0x00000080 /* Enable Beacon use */
+#define AR5K_QCU_MISC_CBR_THRES_ENABLE 0x00000100 /* CBR threshold enabled */
+#define AR5K_QCU_MISC_RDY_VEOL_POLICY 0x00000200 /* TXE reset when RDYTIME enalbed */
+#define AR5K_QCU_MISC_CBR_RESET_CNT 0x00000400 /* CBR threshold (counter) reset */
+#define AR5K_QCU_MISC_DCU_EARLY 0x00000800 /* DCU early termination */
+#define AR5K_QCU_MISC_DCU_CMP_EN 0x00001000 /* Enable frame compression */
#define AR5K_QUEUE_MISC(_q) AR5K_QUEUE_REG(AR5K_QCU_MISC_BASE, _q)
*/
#define AR5K_QCU_STS_BASE 0x0a00 /* Register Address - Queue0 STS */
#define AR5K_QCU_STS_FRMPENDCNT 0x00000003 /* Frames pending counter */
-#define AR5K_QCU_STS_CBREXPCNT 0x0000ff00 /* CBR expired counter (?) */
+#define AR5K_QCU_STS_CBREXPCNT 0x0000ff00 /* CBR expired counter */
#define AR5K_QUEUE_STATUS(_q) AR5K_QUEUE_REG(AR5K_QCU_STS_BASE, _q)
/*
*/
#define AR5K_QCU_CBB_SELECT 0x0b00
#define AR5K_QCU_CBB_ADDR 0x0b04
+#define AR5K_QCU_CBB_ADDR_S 9
/*
* QCU compression buffer configuration register [5212+]
+ * (buffer size)
*/
#define AR5K_QCU_CBCFG 0x0b08
* No lockout means there is no special handling.
*/
#define AR5K_DCU_MISC_BASE 0x1100 /* Register Address -Queue0 DCU_MISC */
-#define AR5K_DCU_MISC_BACKOFF 0x000007ff /* Mask for backoff setting (?) */
+#define AR5K_DCU_MISC_BACKOFF 0x000007ff /* Mask for backoff threshold */
#define AR5K_DCU_MISC_BACKOFF_FRAG 0x00000200 /* Enable backoff while bursting */
-#define AR5K_DCU_MISC_HCFPOLL_ENABLE 0x00000800 /* CF - Poll (?) */
-#define AR5K_DCU_MISC_BACKOFF_PERSIST 0x00001000 /* Persistent backoff (?) */
-#define AR5K_DCU_MISC_FRMPRFTCH_ENABLE 0x00002000 /* Enable frame pre-fetch (?) */
+#define AR5K_DCU_MISC_HCFPOLL_ENABLE 0x00000800 /* CF - Poll enable */
+#define AR5K_DCU_MISC_BACKOFF_PERSIST 0x00001000 /* Persistent backoff */
+#define AR5K_DCU_MISC_FRMPRFTCH_ENABLE 0x00002000 /* Enable frame pre-fetch */
#define AR5K_DCU_MISC_VIRTCOL 0x0000c000 /* Mask for Virtual Collision (?) */
-#define AR5K_DCU_MISC_VIRTCOL_NORMAL 0
-#define AR5K_DCU_MISC_VIRTCOL_MODIFIED 1
-#define AR5K_DCU_MISC_VIRTCOL_IGNORE 2
-#define AR5K_DCU_MISC_BCN_ENABLE 0x00010000 /* Beacon enable (?) */
+#define AR5K_DCU_MISC_VIRTCOL_NORMAL 0
+#define AR5K_DCU_MISC_VIRTCOL_MODIFIED 1
+#define AR5K_DCU_MISC_VIRTCOL_IGNORE 2
+#define AR5K_DCU_MISC_BCN_ENABLE 0x00010000 /* Enable Beacon use */
#define AR5K_DCU_MISC_ARBLOCK_CTL 0x00060000 /* Arbiter lockout control mask */
#define AR5K_DCU_MISC_ARBLOCK_CTL_S 17
-#define AR5K_DCU_MISC_ARBLOCK_CTL_NONE 0 /* No arbiter lockout */
+#define AR5K_DCU_MISC_ARBLOCK_CTL_NONE 0 /* No arbiter lockout */
#define AR5K_DCU_MISC_ARBLOCK_CTL_INTFRM 1 /* Intra-frame lockout */
#define AR5K_DCU_MISC_ARBLOCK_CTL_GLOBAL 2 /* Global lockout */
-#define AR5K_DCU_MISC_ARBLOCK_IGNORE 0x00080000
-#define AR5K_DCU_MISC_SEQ_NUM_INCR_DIS 0x00100000 /* Disable sequence number increment (?) */
-#define AR5K_DCU_MISC_POST_FR_BKOFF_DIS 0x00200000 /* Disable post-frame backoff (?) */
-#define AR5K_DCU_MISC_VIRT_COLL_POLICY 0x00400000 /* Virtual Collision policy (?) */
-#define AR5K_DCU_MISC_BLOWN_IFS_POLICY 0x00800000
+#define AR5K_DCU_MISC_ARBLOCK_IGNORE 0x00080000 /* Ignore Arbiter lockout */
+#define AR5K_DCU_MISC_SEQ_NUM_INCR_DIS 0x00100000 /* Disable sequence number increment */
+#define AR5K_DCU_MISC_POST_FR_BKOFF_DIS 0x00200000 /* Disable post-frame backoff */
+#define AR5K_DCU_MISC_VIRT_COLL_POLICY 0x00400000 /* Virtual Collision cw policy */
+#define AR5K_DCU_MISC_BLOWN_IFS_POLICY 0x00800000 /* Blown IFS policy (?) */
#define AR5K_DCU_MISC_SEQNUM_CTL 0x01000000 /* Sequence number control (?) */
#define AR5K_QUEUE_DFS_MISC(_q) AR5K_QUEUE_REG(AR5K_DCU_MISC_BASE, _q)
/*
* DCU frame sequence number registers
*/
-#define AR5K_DCU_SEQNUM_BASE 0x1140
-#define AR5K_DCU_SEQNUM_M 0x00000fff
+#define AR5K_DCU_SEQNUM_BASE 0x1140
+#define AR5K_DCU_SEQNUM_M 0x00000fff
#define AR5K_QUEUE_DFS_SEQNUM(_q) AR5K_QUEUE_REG(AR5K_DCU_SEQNUM_BASE, _q)
/*
- * DCU global IFS SIFS registers
+ * DCU global IFS SIFS register
*/
#define AR5K_DCU_GBL_IFS_SIFS 0x1030
#define AR5K_DCU_GBL_IFS_SIFS_M 0x0000ffff
/*
- * DCU global IFS slot interval registers
+ * DCU global IFS slot interval register
*/
#define AR5K_DCU_GBL_IFS_SLOT 0x1070
#define AR5K_DCU_GBL_IFS_SLOT_M 0x0000ffff
/*
- * DCU global IFS EIFS registers
+ * DCU global IFS EIFS register
*/
#define AR5K_DCU_GBL_IFS_EIFS 0x10b0
#define AR5K_DCU_GBL_IFS_EIFS_M 0x0000ffff
/*
- * DCU global IFS misc registers
+ * DCU global IFS misc register
+ *
+ * LFSR stands for Linear Feedback Shift Register
+ * and it's used for generating pseudo-random
+ * number sequences.
+ *
+ * (If i understand corectly, random numbers are
+ * used for idle sensing -multiplied with cwmin/max etc-)
*/
#define AR5K_DCU_GBL_IFS_MISC 0x10f0 /* Register Address */
-#define AR5K_DCU_GBL_IFS_MISC_LFSR_SLICE 0x00000007
-#define AR5K_DCU_GBL_IFS_MISC_TURBO_MODE 0x00000008 /* Turbo mode (?) */
-#define AR5K_DCU_GBL_IFS_MISC_SIFS_DUR_USEC 0x000003f0 /* SIFS Duration mask (?) */
-#define AR5K_DCU_GBL_IFS_MISC_USEC_DUR 0x000ffc00
-#define AR5K_DCU_GBL_IFS_MISC_DCU_ARB_DELAY 0x00300000
+#define AR5K_DCU_GBL_IFS_MISC_LFSR_SLICE 0x00000007 /* LFSR Slice Select */
+#define AR5K_DCU_GBL_IFS_MISC_TURBO_MODE 0x00000008 /* Turbo mode */
+#define AR5K_DCU_GBL_IFS_MISC_SIFS_DUR_USEC 0x000003f0 /* SIFS Duration mask */
+#define AR5K_DCU_GBL_IFS_MISC_USEC_DUR 0x000ffc00 /* USEC Duration mask */
+#define AR5K_DCU_GBL_IFS_MISC_DCU_ARB_DELAY 0x00300000 /* DCU Arbiter delay mask */
+#define AR5K_DCU_GBL_IFS_MISC_SIFS_CNT_RST 0x00400000 /* SIFC cnt reset policy (?) */
+#define AR5K_DCU_GBL_IFS_MISC_AIFS_CNT_RST 0x00800000 /* AIFS cnt reset policy (?) */
+#define AR5K_DCU_GBL_IFS_MISC_RND_LFSR_SL_DIS 0x01000000 /* Disable random LFSR slice */
/*
* DCU frame prefetch control register
*/
-#define AR5K_DCU_FP 0x1230
+#define AR5K_DCU_FP 0x1230 /* Register Address */
+#define AR5K_DCU_FP_NOBURST_DCU_EN 0x00000001 /* Enable non-burst prefetch on DCU (?) */
+#define AR5K_DCU_FP_NOBURST_EN 0x00000010 /* Enable non-burst prefetch (?) */
+#define AR5K_DCU_FP_BURST_DCU_EN 0x00000020 /* Enable burst prefetch on DCU (?) */
/*
* DCU transmit pause control/status register
*/
#define AR5K_DCU_TXP 0x1270 /* Register Address */
-#define AR5K_DCU_TXP_M 0x000003ff /* Tx pause mask (?) */
-#define AR5K_DCU_TXP_STATUS 0x00010000 /* Tx pause status (?) */
+#define AR5K_DCU_TXP_M 0x000003ff /* Tx pause mask */
+#define AR5K_DCU_TXP_STATUS 0x00010000 /* Tx pause status */
+
+/*
+ * DCU transmit filter table 0 (32 entries)
+ */
+#define AR5K_DCU_TX_FILTER_0_BASE 0x1038
+#define AR5K_DCU_TX_FILTER_0(_n) (AR5K_DCU_TX_FILTER_0_BASE + (_n * 64))
/*
- * DCU transmit filter register
+ * DCU transmit filter table 1 (16 entries)
*/
-#define AR5K_DCU_TX_FILTER 0x1038
+#define AR5K_DCU_TX_FILTER_1_BASE 0x103c
+#define AR5K_DCU_TX_FILTER_1(_n) (AR5K_DCU_TX_FILTER_1_BASE + ((_n - 32) * 64))
/*
* DCU clear transmit filter register
/*
* Reset control register
- *
- * 4 and 8 are not used in 5211/5212 and
- * 2 means "baseband reset" on 5211/5212.
*/
#define AR5K_RESET_CTL 0x4000 /* Register Address */
#define AR5K_RESET_CTL_PCU 0x00000001 /* Protocol Control Unit reset */
#define AR5K_SLEEP_CTL_SLE_SLP 0x00010000 /* Force chip sleep */
#define AR5K_SLEEP_CTL_SLE_ALLOW 0x00020000
#define AR5K_SLEEP_CTL_SLE_UNITS 0x00000008 /* [5211+] */
+/* more bits */
/*
* Interrupt pending register
* Sleep force register
*/
#define AR5K_SFR 0x400c
-#define AR5K_SFR_M 0x00000001
+#define AR5K_SFR_EN 0x00000001
/*
* PCI configuration register
*/
#define AR5K_PCICFG 0x4010 /* Register Address */
#define AR5K_PCICFG_EEAE 0x00000001 /* Eeprom access enable [5210] */
+#define AR5K_PCICFG_SLEEP_CLOCK_EN 0x00000002 /* Enable sleep clock (?) */
#define AR5K_PCICFG_CLKRUNEN 0x00000004 /* CLKRUN enable [5211+] */
#define AR5K_PCICFG_EESIZE 0x00000018 /* Mask for EEPROM size [5211+] */
#define AR5K_PCICFG_EESIZE_S 3
#define AR5K_PCICFG_CBEFIX_DIS 0x00000400 /* Disable CBE fix (?) */
#define AR5K_PCICFG_SL_INTEN 0x00000800 /* Enable interrupts when asleep (?) */
#define AR5K_PCICFG_LED_BCTL 0x00001000 /* Led blink (?) [5210] */
-#define AR5K_PCICFG_SL_INPEN 0x00002800 /* Sleep even whith pending interrupts (?) */
+#define AR5K_PCICFG_UNK 0x00001000 /* Passed on some parts durring attach (?) */
+#define AR5K_PCICFG_SL_INPEN 0x00002000 /* Sleep even whith pending interrupts (?) */
#define AR5K_PCICFG_SPWR_DN 0x00010000 /* Mask for power status */
#define AR5K_PCICFG_LEDMODE 0x000e0000 /* Ledmode [5211+] */
#define AR5K_PCICFG_LEDMODE_PROP 0x00000000 /* Blink on standard traffic [5211+] */
#define AR5K_PCICFG_LEDMODE_PROM 0x00020000 /* Default mode (blink on any traffic) [5211+] */
#define AR5K_PCICFG_LEDMODE_PWR 0x00040000 /* Some other blinking mode (?) [5211+] */
#define AR5K_PCICFG_LEDMODE_RAND 0x00060000 /* Random blinking (?) [5211+] */
-#define AR5K_PCICFG_LEDBLINK 0x00700000
+#define AR5K_PCICFG_LEDBLINK 0x00700000 /* Led blink rate */
#define AR5K_PCICFG_LEDBLINK_S 20
-#define AR5K_PCICFG_LEDSLOW 0x00800000 /* Slow led blink rate (?) [5211+] */
+#define AR5K_PCICFG_LEDSLOW 0x00800000 /* Slowest led blink rate [5211+] */
#define AR5K_PCICFG_LEDSTATE \
(AR5K_PCICFG_LED | AR5K_PCICFG_LEDMODE | \
AR5K_PCICFG_LEDBLINK | AR5K_PCICFG_LEDSLOW)
+#define AR5K_PCICFG_SLEEP_CLOCK_RATE 0x03000000 /* Sleep clock rate (field) */
/*
* "General Purpose Input/Output" (GPIO) control register
#define AR5K_EEPROM_VERSION_4_4 0x4004
#define AR5K_EEPROM_VERSION_4_5 0x4005
#define AR5K_EEPROM_VERSION_4_6 0x4006 /* has ee_scaled_cck_delta */
-#define AR5K_EEPROM_VERSION_4_7 0x3007
+#define AR5K_EEPROM_VERSION_4_7 0x4007
#define AR5K_EEPROM_MODE_11A 0
#define AR5K_EEPROM_MODE_11B 1
#define AR5K_EEPROM_STAT_WRDONE 0x00000008 /* EEPROM write successful */
/*
- * EEPROM config register (?)
+ * EEPROM config register
*/
-#define AR5K_EEPROM_CFG 0x6010
-
+#define AR5K_EEPROM_CFG 0x6010 /* Register Addres */
+#define AR5K_EEPROM_CFG_SIZE_OVR 0x00000001
+#define AR5K_EEPROM_CFG_WR_WAIT_DIS 0x00000004 /* Disable write wait */
+#define AR5K_EEPROM_CFG_CLK_RATE 0x00000018 /* Clock rate */
+#define AR5K_EEPROM_CFG_PROT_KEY 0x00ffff00 /* Protectio key */
+#define AR5K_EEPROM_CFG_LIND_EN 0x01000000 /* Enable length indicator (?) */
/*
#define AR5K_STA_ID1 0x8004 /* Register Address */
#define AR5K_STA_ID1_AP 0x00010000 /* Set AP mode */
#define AR5K_STA_ID1_ADHOC 0x00020000 /* Set Ad-Hoc mode */
-#define AR5K_STA_ID1_PWR_SV 0x00040000 /* Power save reporting (?) */
+#define AR5K_STA_ID1_PWR_SV 0x00040000 /* Power save reporting */
#define AR5K_STA_ID1_NO_KEYSRCH 0x00080000 /* No key search */
#define AR5K_STA_ID1_NO_PSPOLL 0x00100000 /* No power save polling [5210] */
#define AR5K_STA_ID1_PCF_5211 0x00100000 /* Enable PCF on [5211+] */
AR5K_STA_ID1_PCF_5210 : AR5K_STA_ID1_PCF_5211)
#define AR5K_STA_ID1_DEFAULT_ANTENNA 0x00200000 /* Use default antenna */
#define AR5K_STA_ID1_DESC_ANTENNA 0x00400000 /* Update antenna from descriptor */
-#define AR5K_STA_ID1_RTS_DEF_ANTENNA 0x00800000 /* Use default antenna for RTS (?) */
-#define AR5K_STA_ID1_ACKCTS_6MB 0x01000000 /* Use 6Mbit/s for ACK/CTS (?) */
+#define AR5K_STA_ID1_RTS_DEF_ANTENNA 0x00800000 /* Use default antenna for RTS */
+#define AR5K_STA_ID1_ACKCTS_6MB 0x01000000 /* Use 6Mbit/s for ACK/CTS */
#define AR5K_STA_ID1_BASE_RATE_11B 0x02000000 /* Use 11b base rate (for ACK/CTS ?) [5211+] */
+#define AR5K_STA_ID1_SELF_GEN_SECTORE 0x04000000 /* Self generate sectore (?) */
+#define AR5K_STA_ID1_CRYPT_MIC_EN 0x08000000 /* Enable MIC */
+#define AR5K_STA_ID1_KEYSRCH_MODE 0x10000000 /* Keysearch mode (?) */
+#define AR5K_STA_ID1_PRESERVE_SEQ_NUM 0x20000000 /* Preserve sequence number */
/*
* First BSSID register (MAC address, lower 32bits)
*
* Retry limit register for 5210 (no QCU/DCU so it's done in PCU)
*/
-#define AR5K_NODCU_RETRY_LMT 0x801c /*Register Address */
+#define AR5K_NODCU_RETRY_LMT 0x801c /* Register Address */
#define AR5K_NODCU_RETRY_LMT_SH_RETRY 0x0000000f /* Short retry limit mask */
#define AR5K_NODCU_RETRY_LMT_SH_RETRY_S 0
#define AR5K_NODCU_RETRY_LMT_LG_RETRY 0x000000f0 /* Long retry mask */
#define AR5K_USEC_5211 0x801c /* Register Address [5211+] */
#define AR5K_USEC (ah->ah_version == AR5K_AR5210 ? \
AR5K_USEC_5210 : AR5K_USEC_5211)
-#define AR5K_USEC_1 0x0000007f
+#define AR5K_USEC_1 0x0000007f /* clock cycles for 1us */
#define AR5K_USEC_1_S 0
-#define AR5K_USEC_32 0x00003f80
+#define AR5K_USEC_32 0x00003f80 /* clock cycles for 1us while on 32Mhz clock */
#define AR5K_USEC_32_S 7
#define AR5K_USEC_TX_LATENCY_5211 0x007fc000
#define AR5K_USEC_TX_LATENCY_5211_S 14
/*
* PCU beacon control register
*/
-#define AR5K_BEACON_5210 0x8024
-#define AR5K_BEACON_5211 0x8020
+#define AR5K_BEACON_5210 0x8024 /*Register Address [5210] */
+#define AR5K_BEACON_5211 0x8020 /*Register Address [5211+] */
#define AR5K_BEACON (ah->ah_version == AR5K_AR5210 ? \
AR5K_BEACON_5210 : AR5K_BEACON_5211)
-#define AR5K_BEACON_PERIOD 0x0000ffff
+#define AR5K_BEACON_PERIOD 0x0000ffff /* Mask for beacon period */
#define AR5K_BEACON_PERIOD_S 0
-#define AR5K_BEACON_TIM 0x007f0000
+#define AR5K_BEACON_TIM 0x007f0000 /* Mask for TIM offset */
#define AR5K_BEACON_TIM_S 16
-#define AR5K_BEACON_ENABLE 0x00800000
-#define AR5K_BEACON_RESET_TSF 0x01000000
+#define AR5K_BEACON_ENABLE 0x00800000 /* Enable beacons */
+#define AR5K_BEACON_RESET_TSF 0x01000000 /* Force TSF reset */
/*
* CFP period register
/*
* Receive filter register
- * TODO: Get these out of ar5xxx.h on ath5k
*/
#define AR5K_RX_FILTER_5210 0x804c /* Register Address [5210] */
#define AR5K_RX_FILTER_5211 0x803c /* Register Address [5211+] */
#define AR5K_DIAG_SW_5211 0x8048 /* Register Address [5211+] */
#define AR5K_DIAG_SW (ah->ah_version == AR5K_AR5210 ? \
AR5K_DIAG_SW_5210 : AR5K_DIAG_SW_5211)
-#define AR5K_DIAG_SW_DIS_WEP_ACK 0x00000001
-#define AR5K_DIAG_SW_DIS_ACK 0x00000002 /* Disable ACKs (?) */
-#define AR5K_DIAG_SW_DIS_CTS 0x00000004 /* Disable CTSs (?) */
-#define AR5K_DIAG_SW_DIS_ENC 0x00000008 /* Disable encryption (?) */
-#define AR5K_DIAG_SW_DIS_DEC 0x00000010 /* Disable decryption (?) */
+#define AR5K_DIAG_SW_DIS_WEP_ACK 0x00000001 /* Disable ACKs if WEP key is invalid */
+#define AR5K_DIAG_SW_DIS_ACK 0x00000002 /* Disable ACKs */
+#define AR5K_DIAG_SW_DIS_CTS 0x00000004 /* Disable CTSs */
+#define AR5K_DIAG_SW_DIS_ENC 0x00000008 /* Disable encryption */
+#define AR5K_DIAG_SW_DIS_DEC 0x00000010 /* Disable decryption */
#define AR5K_DIAG_SW_DIS_TX 0x00000020 /* Disable transmit [5210] */
#define AR5K_DIAG_SW_DIS_RX_5210 0x00000040 /* Disable recieve */
#define AR5K_DIAG_SW_DIS_RX_5211 0x00000020
#define AR5K_DIAG_SW_CHAN_INFO_5211 0x00000100
#define AR5K_DIAG_SW_CHAN_INFO (ah->ah_version == AR5K_AR5210 ? \
AR5K_DIAG_SW_CHAN_INFO_5210 : AR5K_DIAG_SW_CHAN_INFO_5211)
-#define AR5K_DIAG_SW_EN_SCRAM_SEED_5211 0x00000200 /* Scrambler seed (?) */
+#define AR5K_DIAG_SW_EN_SCRAM_SEED_5211 0x00000200 /* Enable scrambler seed */
#define AR5K_DIAG_SW_EN_SCRAM_SEED_5210 0x00000400
#define AR5K_DIAG_SW_EN_SCRAM_SEED (ah->ah_version == AR5K_AR5210 ? \
AR5K_DIAG_SW_EN_SCRAM_SEED_5210 : AR5K_DIAG_SW_EN_SCRAM_SEED_5211)
#define AR5K_DIAG_SW_ECO_ENABLE 0x00000400 /* [5211+] */
#define AR5K_DIAG_SW_SCVRAM_SEED 0x0003f800 /* [5210] */
-#define AR5K_DIAG_SW_SCRAM_SEED_M 0x0001fc00 /* Scrambler seed mask (?) */
+#define AR5K_DIAG_SW_SCRAM_SEED_M 0x0001fc00 /* Scrambler seed mask */
#define AR5K_DIAG_SW_SCRAM_SEED_S 10
#define AR5K_DIAG_SW_DIS_SEQ_INC 0x00040000 /* Disable seqnum increment (?)[5210] */
#define AR5K_DIAG_SW_FRAME_NV0_5210 0x00080000
AR5K_DIAG_SW_FRAME_NV0_5210 : AR5K_DIAG_SW_FRAME_NV0_5211)
#define AR5K_DIAG_SW_OBSPT_M 0x000c0000
#define AR5K_DIAG_SW_OBSPT_S 18
+/* more bits */
/*
* TSF (clock) register (lower 32 bits)
/*
* ADDAC test register [5211+]
*/
-#define AR5K_ADDAC_TEST 0x8054
-#define AR5K_ADDAC_TEST_TXCONT 0x00000001
+#define AR5K_ADDAC_TEST 0x8054 /* Register Address */
+#define AR5K_ADDAC_TEST_TXCONT 0x00000001 /* Test continuous tx */
+#define AR5K_ADDAC_TEST_TST_MODE 0x00000002 /* Test mode */
+#define AR5K_ADDAC_TEST_LOOP_EN 0x00000004 /* Enable loop */
+#define AR5K_ADDAC_TEST_LOOP_LEN 0x00000008 /* Loop length (field) */
+#define AR5K_ADDAC_TEST_USE_U8 0x00004000 /* Use upper 8 bits */
+#define AR5K_ADDAC_TEST_MSB 0x00008000 /* State of MSB */
+#define AR5K_ADDAC_TEST_TRIG_SEL 0x00010000 /* Trigger select */
+#define AR5K_ADDAC_TEST_TRIG_PTY 0x00020000 /* Trigger polarity */
+#define AR5K_ADDAC_TEST_RXCONT 0x00040000 /* Continuous capture */
+#define AR5K_ADDAC_TEST_CAPTURE 0x00080000 /* Begin capture */
+#define AR5K_ADDAC_TEST_TST_ARM 0x00100000 /* Test ARM (Adaptive Radio Mode ?) */
/*
* Default antenna register [5211+]
*/
#define AR5K_DEFAULT_ANTENNA 0x8058
+/*
+ * Frame control QoS mask register (?) [5211+]
+ * (FC_QOS_MASK)
+ */
+#define AR5K_FRAME_CTL_QOSM 0x805c
+/*
+ * Seq mask register (?) [5211+]
+ */
+#define AR5K_SEQ_MASK 0x8060
/*
* Retry count register [5210]
/*
* XR (eXtended Range) mode register
*/
-#define AR5K_XRMODE 0x80c0
-#define AR5K_XRMODE_POLL_TYPE_M 0x0000003f
+#define AR5K_XRMODE 0x80c0 /* Register Address */
+#define AR5K_XRMODE_POLL_TYPE_M 0x0000003f /* Mask for Poll type (?) */
#define AR5K_XRMODE_POLL_TYPE_S 0
-#define AR5K_XRMODE_POLL_SUBTYPE_M 0x0000003c
+#define AR5K_XRMODE_POLL_SUBTYPE_M 0x0000003c /* Mask for Poll subtype (?) */
#define AR5K_XRMODE_POLL_SUBTYPE_S 2
-#define AR5K_XRMODE_POLL_WAIT_ALL 0x00000080
-#define AR5K_XRMODE_SIFS_DELAY 0x000fff00
-#define AR5K_XRMODE_FRAME_HOLD_M 0xfff00000
+#define AR5K_XRMODE_POLL_WAIT_ALL 0x00000080 /* Wait for poll */
+#define AR5K_XRMODE_SIFS_DELAY 0x000fff00 /* Mask for SIFS delay */
+#define AR5K_XRMODE_FRAME_HOLD_M 0xfff00000 /* Mask for frame hold (?) */
#define AR5K_XRMODE_FRAME_HOLD_S 20
/*
* XR delay register
*/
-#define AR5K_XRDELAY 0x80c4
-#define AR5K_XRDELAY_SLOT_DELAY_M 0x0000ffff
+#define AR5K_XRDELAY 0x80c4 /* Register Address */
+#define AR5K_XRDELAY_SLOT_DELAY_M 0x0000ffff /* Mask for slot delay */
#define AR5K_XRDELAY_SLOT_DELAY_S 0
-#define AR5K_XRDELAY_CHIRP_DELAY_M 0xffff0000
+#define AR5K_XRDELAY_CHIRP_DELAY_M 0xffff0000 /* Mask for CHIRP data delay */
#define AR5K_XRDELAY_CHIRP_DELAY_S 16
/*
* XR timeout register
*/
-#define AR5K_XRTIMEOUT 0x80c8
-#define AR5K_XRTIMEOUT_CHIRP_M 0x0000ffff
+#define AR5K_XRTIMEOUT 0x80c8 /* Register Address */
+#define AR5K_XRTIMEOUT_CHIRP_M 0x0000ffff /* Mask for CHIRP timeout */
#define AR5K_XRTIMEOUT_CHIRP_S 0
-#define AR5K_XRTIMEOUT_POLL_M 0xffff0000
+#define AR5K_XRTIMEOUT_POLL_M 0xffff0000 /* Mask for Poll timeout */
#define AR5K_XRTIMEOUT_POLL_S 16
/*
* XR chirp register
*/
-#define AR5K_XRCHIRP 0x80cc
-#define AR5K_XRCHIRP_SEND 0x00000001
-#define AR5K_XRCHIRP_GAP 0xffff0000
+#define AR5K_XRCHIRP 0x80cc /* Register Address */
+#define AR5K_XRCHIRP_SEND 0x00000001 /* Send CHIRP */
+#define AR5K_XRCHIRP_GAP 0xffff0000 /* Mask for CHIRP gap (?) */
/*
* XR stomp register
*/
-#define AR5K_XRSTOMP 0x80d0
-#define AR5K_XRSTOMP_TX 0x00000001
-#define AR5K_XRSTOMP_RX_ABORT 0x00000002
-#define AR5K_XRSTOMP_RSSI_THRES 0x0000ff00
+#define AR5K_XRSTOMP 0x80d0 /* Register Address */
+#define AR5K_XRSTOMP_TX 0x00000001 /* Stomp Tx (?) */
+#define AR5K_XRSTOMP_RX 0x00000002 /* Stomp Rx (?) */
+#define AR5K_XRSTOMP_TX_RSSI 0x00000004 /* Stomp Tx RSSI (?) */
+#define AR5K_XRSTOMP_TX_BSSID 0x00000008 /* Stomp Tx BSSID (?) */
+#define AR5K_XRSTOMP_DATA 0x00000010 /* Stomp data (?)*/
+#define AR5K_XRSTOMP_RSSI_THRES 0x0000ff00 /* Mask for XR RSSI threshold */
/*
* First enhanced sleep register
*/
-#define AR5K_SLEEP0 0x80d4
-#define AR5K_SLEEP0_NEXT_DTIM 0x0007ffff
+#define AR5K_SLEEP0 0x80d4 /* Register Address */
+#define AR5K_SLEEP0_NEXT_DTIM 0x0007ffff /* Mask for next DTIM (?) */
#define AR5K_SLEEP0_NEXT_DTIM_S 0
-#define AR5K_SLEEP0_ASSUME_DTIM 0x00080000
-#define AR5K_SLEEP0_ENH_SLEEP_EN 0x00100000
-#define AR5K_SLEEP0_CABTO 0xff000000
+#define AR5K_SLEEP0_ASSUME_DTIM 0x00080000 /* Assume DTIM */
+#define AR5K_SLEEP0_ENH_SLEEP_EN 0x00100000 /* Enable enchanced sleep control */
+#define AR5K_SLEEP0_CABTO 0xff000000 /* Mask for CAB Time Out */
#define AR5K_SLEEP0_CABTO_S 24
/*
* Second enhanced sleep register
*/
-#define AR5K_SLEEP1 0x80d8
-#define AR5K_SLEEP1_NEXT_TIM 0x0007ffff
+#define AR5K_SLEEP1 0x80d8 /* Register Address */
+#define AR5K_SLEEP1_NEXT_TIM 0x0007ffff /* Mask for next TIM (?) */
#define AR5K_SLEEP1_NEXT_TIM_S 0
-#define AR5K_SLEEP1_BEACON_TO 0xff000000
+#define AR5K_SLEEP1_BEACON_TO 0xff000000 /* Mask for Beacon Time Out */
#define AR5K_SLEEP1_BEACON_TO_S 24
/*
* Third enhanced sleep register
*/
-#define AR5K_SLEEP2 0x80dc
-#define AR5K_SLEEP2_TIM_PER 0x0000ffff
+#define AR5K_SLEEP2 0x80dc /* Register Address */
+#define AR5K_SLEEP2_TIM_PER 0x0000ffff /* Mask for TIM period (?) */
#define AR5K_SLEEP2_TIM_PER_S 0
-#define AR5K_SLEEP2_DTIM_PER 0xffff0000
+#define AR5K_SLEEP2_DTIM_PER 0xffff0000 /* Mask for DTIM period (?) */
#define AR5K_SLEEP2_DTIM_PER_S 16
/*
* BSSID mask registers
*/
-#define AR5K_BSS_IDM0 0x80e0
-#define AR5K_BSS_IDM1 0x80e4
+#define AR5K_BSS_IDM0 0x80e0 /* Upper bits */
+#define AR5K_BSS_IDM1 0x80e4 /* Lower bits */
/*
* TX power control (TPC) register
+ *
+ * XXX: PCDAC steps (0.5dbm) or DBM ?
+ *
+ * XXX: Mask changes for newer chips to 7f
+ * like tx power table ?
*/
-#define AR5K_TXPC 0x80e8
-#define AR5K_TXPC_ACK_M 0x0000003f
+#define AR5K_TXPC 0x80e8 /* Register Address */
+#define AR5K_TXPC_ACK_M 0x0000003f /* Mask for ACK tx power */
#define AR5K_TXPC_ACK_S 0
-#define AR5K_TXPC_CTS_M 0x00003f00
+#define AR5K_TXPC_CTS_M 0x00003f00 /* Mask for CTS tx power */
#define AR5K_TXPC_CTS_S 8
-#define AR5K_TXPC_CHIRP_M 0x003f0000
+#define AR5K_TXPC_CHIRP_M 0x003f0000 /* Mask for CHIRP tx power */
#define AR5K_TXPC_CHIRP_S 22
/*
* Profile count registers
*/
-#define AR5K_PROFCNT_TX 0x80ec
-#define AR5K_PROFCNT_RX 0x80f0
-#define AR5K_PROFCNT_RXCLR 0x80f4
-#define AR5K_PROFCNT_CYCLE 0x80f8
+#define AR5K_PROFCNT_TX 0x80ec /* Tx count */
+#define AR5K_PROFCNT_RX 0x80f0 /* Rx count */
+#define AR5K_PROFCNT_RXCLR 0x80f4 /* Clear Rx count */
+#define AR5K_PROFCNT_CYCLE 0x80f8 /* Cycle count (?) */
+
+/*
+ * Quiet (period) control registers (?)
+ */
+#define AR5K_QUIET_CTL1 0x80fc /* Register Address */
+#define AR5K_QUIET_CTL1_NEXT_QT 0x0000ffff /* Mask for next quiet (period?) (?) */
+#define AR5K_QUIET_CTL1_QT_EN 0x00010000 /* Enable quiet (period?) */
+#define AR5K_QUIET_CTL2 0x8100 /* Register Address */
+#define AR5K_QUIET_CTL2_QT_PER 0x0000ffff /* Mask for quiet period (?) */
+#define AR5K_QUIET_CTL2_QT_DUR 0xffff0000 /* Mask for quiet duration (?) */
/*
* TSF parameter register
*/
-#define AR5K_TSF_PARM 0x8104
-#define AR5K_TSF_PARM_INC_M 0x000000ff
+#define AR5K_TSF_PARM 0x8104 /* Register Address */
+#define AR5K_TSF_PARM_INC_M 0x000000ff /* Mask for TSF increment */
#define AR5K_TSF_PARM_INC_S 0
+/*
+ * QoS register (?)
+ */
+#define AR5K_QOS 0x8108 /* Register Address */
+#define AR5K_QOS_NOACK_2BIT_VALUES 0x00000000 /* (field) */
+#define AR5K_QOS_NOACK_BIT_OFFSET 0x00000020 /* (field) */
+#define AR5K_QOS_NOACK_BYTE_OFFSET 0x00000080 /* (field) */
+
/*
* PHY error filter register
*/
#define AR5K_PHY_ERR_FIL 0x810c
-#define AR5K_PHY_ERR_FIL_RADAR 0x00000020
-#define AR5K_PHY_ERR_FIL_OFDM 0x00020000
-#define AR5K_PHY_ERR_FIL_CCK 0x02000000
+#define AR5K_PHY_ERR_FIL_RADAR 0x00000020 /* Radar signal */
+#define AR5K_PHY_ERR_FIL_OFDM 0x00020000 /* OFDM false detect (ANI) */
+#define AR5K_PHY_ERR_FIL_CCK 0x02000000 /* CCK false detect (ANI) */
+
+/*
+ * XR latency register
+ */
+#define AR5K_XRLAT_TX 0x8110
/*
- * Rate duration register
+ * ACK SIFS register
+ */
+#define AR5K_ACKSIFS 0x8114 /* Register Address */
+#define AR5K_ACKSIFS_INC 0x00000000 /* ACK SIFS Increment (field) */
+
+/*
+ * MIC QoS control register (?)
+ */
+#define AR5K_MIC_QOS_CTL 0x8118 /* Register Address */
+#define AR5K_MIC_QOS_CTL_0 0x00000001 /* MIC QoS control 0 (?) */
+#define AR5K_MIC_QOS_CTL_1 0x00000004 /* MIC QoS control 1 (?) */
+#define AR5K_MIC_QOS_CTL_2 0x00000010 /* MIC QoS control 2 (?) */
+#define AR5K_MIC_QOS_CTL_3 0x00000040 /* MIC QoS control 3 (?) */
+#define AR5K_MIC_QOS_CTL_4 0x00000100 /* MIC QoS control 4 (?) */
+#define AR5K_MIC_QOS_CTL_5 0x00000400 /* MIC QoS control 5 (?) */
+#define AR5K_MIC_QOS_CTL_6 0x00001000 /* MIC QoS control 6 (?) */
+#define AR5K_MIC_QOS_CTL_7 0x00004000 /* MIC QoS control 7 (?) */
+#define AR5K_MIC_QOS_CTL_MQ_EN 0x00010000 /* Enable MIC QoS */
+
+/*
+ * MIC QoS select register (?)
+ */
+#define AR5K_MIC_QOS_SEL 0x811c
+#define AR5K_MIC_QOS_SEL_0 0x00000001
+#define AR5K_MIC_QOS_SEL_1 0x00000010
+#define AR5K_MIC_QOS_SEL_2 0x00000100
+#define AR5K_MIC_QOS_SEL_3 0x00001000
+#define AR5K_MIC_QOS_SEL_4 0x00010000
+#define AR5K_MIC_QOS_SEL_5 0x00100000
+#define AR5K_MIC_QOS_SEL_6 0x01000000
+#define AR5K_MIC_QOS_SEL_7 0x10000000
+
+/*
+ * Misc mode control register (?)
+ */
+#define AR5K_MISC_MODE 0x8120 /* Register Address */
+#define AR5K_MISC_MODE_FBSSID_MATCH 0x00000001 /* Force BSSID match */
+#define AR5K_MISC_MODE_ACKSIFS_MEM 0x00000002 /* ACK SIFS memory (?) */
+/* more bits */
+
+/*
+ * OFDM Filter counter
+ */
+#define AR5K_OFDM_FIL_CNT 0x8124
+
+/*
+ * CCK Filter counter
+ */
+#define AR5K_CCK_FIL_CNT 0x8128
+
+/*
+ * PHY Error Counters (?)
+ */
+#define AR5K_PHYERR_CNT1 0x812c
+#define AR5K_PHYERR_CNT1_MASK 0x8130
+
+#define AR5K_PHYERR_CNT2 0x8134
+#define AR5K_PHYERR_CNT2_MASK 0x8138
+
+/*
+ * TSF Threshold register (?)
+ */
+#define AR5K_TSF_THRES 0x813c
+
+/*
+ * Rate -> ACK SIFS mapping table (32 entries)
+ */
+#define AR5K_RATE_ACKSIFS_BASE 0x8680 /* Register Address */
+#define AR5K_RATE_ACKSIFS(_n) (AR5K_RATE_ACKSIFS_BSE + ((_n) << 2))
+#define AR5K_RATE_ACKSIFS_NORMAL 0x00000001 /* Normal SIFS (field) */
+#define AR5K_RATE_ACKSIFS_TURBO 0x00000400 /* Turbo SIFS (field) */
+
+/*
+ * Rate -> duration mapping table (32 entries)
*/
#define AR5K_RATE_DUR_BASE 0x8700
#define AR5K_RATE_DUR(_n) (AR5K_RATE_DUR_BASE + ((_n) << 2))
+/*
+ * Rate -> db mapping table
+ * (8 entries, each one has 4 8bit fields)
+ */
+#define AR5K_RATE2DB_BASE 0x87c0
+#define AR5K_RATE2DB(_n) (AR5K_RATE2DB_BASE + ((_n) << 2))
+
+/*
+ * db -> Rate mapping table
+ * (8 entries, each one has 4 8bit fields)
+ */
+#define AR5K_DB2RATE_BASE 0x87e0
+#define AR5K_DB2RATE(_n) (AR5K_DB2RATE_BASE + ((_n) << 2))
+
/*===5212 end===*/
/*
/*===PHY REGISTERS===*/
/*
- * PHY register
+ * PHY registers start
*/
#define AR5K_PHY_BASE 0x9800
#define AR5K_PHY(_n) (AR5K_PHY_BASE + ((_n) << 2))
-#define AR5K_PHY_SHIFT_2GHZ 0x00004007
-#define AR5K_PHY_SHIFT_5GHZ 0x00000007
+
+/*
+ * TST_2 (Misc config parameters)
+ */
+#define AR5K_PHY_TST2 0x9800 /* Register Address */
+#define AR5K_PHY_TST2_TRIG_SEL 0x00000001 /* Trigger select (?) (field ?) */
+#define AR5K_PHY_TST2_TRIG 0x00000010 /* Trigger (?) (field ?) */
+#define AR5K_PHY_TST2_CBUS_MODE 0x00000100 /* Cardbus mode (?) */
+/* bit reserved */
+#define AR5K_PHY_TST2_CLK32 0x00000400 /* CLK_OUT is CLK32 (32Khz external) */
+#define AR5K_PHY_TST2_CHANCOR_DUMP_EN 0x00000800 /* Enable Chancor dump (?) */
+#define AR5K_PHY_TST2_EVEN_CHANCOR_DUMP 0x00001000 /* Even Chancor dump (?) */
+#define AR5K_PHY_TST2_RFSILENT_EN 0x00002000 /* Enable RFSILENT */
+#define AR5K_PHY_TST2_ALT_RFDATA 0x00004000 /* Alternate RFDATA (5-2GHz switch) */
+#define AR5K_PHY_TST2_MINI_OBS_EN 0x00008000 /* Enable mini OBS (?) */
+#define AR5K_PHY_TST2_RX2_IS_RX5_INV 0x00010000 /* 2GHz rx path is the 5GHz path inverted (?) */
+#define AR5K_PHY_TST2_SLOW_CLK160 0x00020000 /* Slow CLK160 (?) */
+#define AR5K_PHY_TST2_AGC_OBS_SEL_3 0x00040000 /* AGC OBS Select 3 (?) */
+#define AR5K_PHY_TST2_BBB_OBS_SEL 0x00080000 /* BB OBS Select (field ?) */
+#define AR5K_PHY_TST2_ADC_OBS_SEL 0x00800000 /* ADC OBS Select (field ?) */
+#define AR5K_PHY_TST2_RX_CLR_SEL 0x08000000 /* RX Clear Select (?) */
+#define AR5K_PHY_TST2_FORCE_AGC_CLR 0x10000000 /* Force AGC clear (?) */
+#define AR5K_PHY_SHIFT_2GHZ 0x00004007 /* Used to access 2GHz radios */
+#define AR5K_PHY_SHIFT_5GHZ 0x00000007 /* Used to access 5GHz radios (default) */
/*
* PHY frame control register [5110] /turbo mode register [5111+]
* a "turbo mode register" for 5110. We treat this one as
* a frame control register for 5110 below.
*/
-#define AR5K_PHY_TURBO 0x9804
-#define AR5K_PHY_TURBO_MODE 0x00000001
-#define AR5K_PHY_TURBO_SHORT 0x00000002
+#define AR5K_PHY_TURBO 0x9804 /* Register Address */
+#define AR5K_PHY_TURBO_MODE 0x00000001 /* Enable turbo mode */
+#define AR5K_PHY_TURBO_SHORT 0x00000002 /* Short mode (20Mhz channels) (?) */
/*
* PHY agility command register
+ * (aka TST_1)
*/
-#define AR5K_PHY_AGC 0x9808
-#define AR5K_PHY_AGC_DISABLE 0x08000000
+#define AR5K_PHY_AGC 0x9808 /* Register Address */
+#define AR5K_PHY_TST1 0x9808
+#define AR5K_PHY_AGC_DISABLE 0x08000000 /* Disable AGC to A2 (?)*/
+#define AR5K_PHY_TST1_TXHOLD 0x00003800 /* Set tx hold (?) */
/*
- * PHY timing register [5112+]
+ * PHY timing register 3 [5112+]
*/
#define AR5K_PHY_TIMING_3 0x9814
#define AR5K_PHY_TIMING_3_DSC_MAN 0xfffe0000
/*
* PHY activation register
*/
-#define AR5K_PHY_ACT 0x981c
-#define AR5K_PHY_ACT_ENABLE 0x00000001
-#define AR5K_PHY_ACT_DISABLE 0x00000002
+#define AR5K_PHY_ACT 0x981c /* Register Address */
+#define AR5K_PHY_ACT_ENABLE 0x00000001 /* Activate PHY */
+#define AR5K_PHY_ACT_DISABLE 0x00000002 /* Deactivate PHY */
+
+/*
+ * PHY RF control registers
+ * (i think these are delay times,
+ * these calibration values exist
+ * in EEPROM)
+ */
+#define AR5K_PHY_RF_CTL2 0x9824 /* Register Address */
+#define AR5K_PHY_RF_CTL2_TXF2TXD_START 0x0000000f /* Mask for TX frame to TX d(esc?) start */
+
+#define AR5K_PHY_RF_CTL3 0x9828 /* Register Address */
+#define AR5K_PHY_RF_CTL3_TXE2XLNA_ON 0x0000000f /* Mask for TX end to XLNA on */
+
+#define AR5K_PHY_RF_CTL4 0x9834 /* Register Address */
+#define AR5K_PHY_RF_CTL4_TXF2XPA_A_ON 0x00000001 /* TX frame to XPA A on (field) */
+#define AR5K_PHY_RF_CTL4_TXF2XPA_B_ON 0x00000100 /* TX frame to XPA B on (field) */
+#define AR5K_PHY_RF_CTL4_TXE2XPA_A_OFF 0x00010000 /* TX end to XPA A off (field) */
+#define AR5K_PHY_RF_CTL4_TXE2XPA_B_OFF 0x01000000 /* TX end to XPA B off (field) */
+
+/*
+ * Pre-Amplifier control register
+ * (XPA -> external pre-amplifier)
+ */
+#define AR5K_PHY_PA_CTL 0x9838 /* Register Address */
+#define AR5K_PHY_PA_CTL_XPA_A_HI 0x00000001 /* XPA A high (?) */
+#define AR5K_PHY_PA_CTL_XPA_B_HI 0x00000002 /* XPA B high (?) */
+#define AR5K_PHY_PA_CTL_XPA_A_EN 0x00000004 /* Enable XPA A */
+#define AR5K_PHY_PA_CTL_XPA_B_EN 0x00000008 /* Enable XPA B */
+
+/*
+ * PHY settling register
+ */
+#define AR5K_PHY_SETTLING 0x9844 /* Register Address */
+#define AR5K_PHY_SETTLING_AGC 0x0000007f /* Mask for AGC settling time */
+#define AR5K_PHY_SETTLING_SWITCH 0x00003f80 /* Mask for Switch settlig time */
+
+/*
+ * PHY Gain registers
+ */
+#define AR5K_PHY_GAIN 0x9848 /* Register Address */
+#define AR5K_PHY_GAIN_TXRX_ATTEN 0x0003f000 /* Mask for TX-RX Attenuation */
+
+#define AR5K_PHY_GAIN_OFFSET 0x984c /* Register Address */
+#define AR5K_PHY_GAIN_OFFSET_RXTX_FLAG 0x00020000 /* RX-TX flag (?) */
+
+/*
+ * Desired size register
+ * (for more infos read ANI patent)
+ */
+#define AR5K_PHY_DESIRED_SIZE 0x9850 /* Register Address */
+#define AR5K_PHY_DESIRED_SIZE_ADC 0x000000ff /* Mask for ADC desired size */
+#define AR5K_PHY_DESIRED_SIZE_PGA 0x0000ff00 /* Mask for PGA desired size */
+#define AR5K_PHY_DESIRED_SIZE_TOT 0x0ff00000 /* Mask for Total desired size (?) */
/*
* PHY signal register
+ * (for more infos read ANI patent)
*/
-#define AR5K_PHY_SIG 0x9858
-#define AR5K_PHY_SIG_FIRSTEP 0x0003f000
+#define AR5K_PHY_SIG 0x9858 /* Register Address */
+#define AR5K_PHY_SIG_FIRSTEP 0x0003f000 /* Mask for FIRSTEP */
#define AR5K_PHY_SIG_FIRSTEP_S 12
-#define AR5K_PHY_SIG_FIRPWR 0x03fc0000
+#define AR5K_PHY_SIG_FIRPWR 0x03fc0000 /* Mask for FIPWR */
#define AR5K_PHY_SIG_FIRPWR_S 18
/*
* PHY coarse agility control register
+ * (for more infos read ANI patent)
*/
-#define AR5K_PHY_AGCCOARSE 0x985c
-#define AR5K_PHY_AGCCOARSE_LO 0x00007f80
+#define AR5K_PHY_AGCCOARSE 0x985c /* Register Address */
+#define AR5K_PHY_AGCCOARSE_LO 0x00007f80 /* Mask for AGC Coarse low */
#define AR5K_PHY_AGCCOARSE_LO_S 7
-#define AR5K_PHY_AGCCOARSE_HI 0x003f8000
+#define AR5K_PHY_AGCCOARSE_HI 0x003f8000 /* Mask for AGC Coarse high */
#define AR5K_PHY_AGCCOARSE_HI_S 15
/*
/*
* PHY noise floor status register
*/
-#define AR5K_PHY_NF 0x9864
-#define AR5K_PHY_NF_M 0x000001ff
-#define AR5K_PHY_NF_ACTIVE 0x00000100
+#define AR5K_PHY_NF 0x9864 /* Register address */
+#define AR5K_PHY_NF_M 0x000001ff /* Noise floor mask */
+#define AR5K_PHY_NF_ACTIVE 0x00000100 /* Noise floor calibration still active */
#define AR5K_PHY_NF_RVAL(_n) (((_n) >> 19) & AR5K_PHY_NF_M)
#define AR5K_PHY_NF_AVAL(_n) (-((_n) ^ AR5K_PHY_NF_M) + 1)
#define AR5K_PHY_NF_SVAL(_n) (((_n) & AR5K_PHY_NF_M) | (1 << 9))
+#define AR5K_PHY_NF_THRESH62 0x00001000 /* Thresh62 -check ANI patent- (field) */
/*
* PHY ADC saturation register [5110]
#define AR5K_PHY_ADCSAT_THR 0x000007e0
#define AR5K_PHY_ADCSAT_THR_S 5
+/*
+ * PHY Weak ofdm signal detection threshold registers (ANI) [5212+]
+ */
+
+/* High thresholds */
+#define AR5K_PHY_WEAK_OFDM_HIGH_THR 0x9868
+#define AR5K_PHY_WEAK_OFDM_HIGH_THR_M2_COUNT 0x0000001f
+#define AR5K_PHY_WEAK_OFDM_HIGH_THR_M2_COUNT_S 0
+#define AR5K_PHY_WEAK_OFDM_HIGH_THR_M1 0x00fe0000
+#define AR5K_PHY_WEAK_OFDM_HIGH_THR_M1_S 17
+#define AR5K_PHY_WEAK_OFDM_HIGH_THR_M2 0x7f000000
+#define AR5K_PHY_WEAK_OFDM_HIGH_THR_M2_S 24
+
+/* Low thresholds */
+#define AR5K_PHY_WEAK_OFDM_LOW_THR 0x986c
+#define AR5K_PHY_WEAK_OFDM_LOW_THR_SELFCOR_EN 0x00000001
+#define AR5K_PHY_WEAK_OFDM_LOW_THR_M2_COUNT 0x00003f00
+#define AR5K_PHY_WEAK_OFDM_LOW_THR_M2_COUNT_S 8
+#define AR5K_PHY_WEAK_OFDM_LOW_THR_M1 0x001fc000
+#define AR5K_PHY_WEAK_OFDM_LOW_THR_M1_S 14
+#define AR5K_PHY_WEAK_OFDM_LOW_THR_M2 0x0fe00000
+#define AR5K_PHY_WEAK_OFDM_LOW_THR_M2_S 21
+
+
/*
* PHY sleep registers [5112+]
*/
AR5K_PHY_PLL_44MHZ_5211 : AR5K_PHY_PLL_44MHZ_5212)
#define AR5K_PHY_PLL_RF5111 0x00000000
#define AR5K_PHY_PLL_RF5112 0x00000040
+#define AR5K_PHY_PLL_HALF_RATE 0x00000100
+#define AR5K_PHY_PLL_QUARTER_RATE 0x00000200
/*
* RF Buffer register
#define AR5K_PHY_RFSTG 0x98d4
#define AR5K_PHY_RFSTG_DISABLE 0x00000021
+/*
+ * PHY Antenna control register
+ */
+#define AR5K_PHY_ANT_CTL 0x9910 /* Register Address */
+#define AR5K_PHY_ANT_CTL_TXRX_EN 0x00000001 /* Enable TX/RX (?) */
+#define AR5K_PHY_ANT_CTL_SECTORED_ANT 0x00000004 /* Sectored Antenna */
+#define AR5K_PHY_ANT_CTL_HITUNE5 0x00000008 /* Hitune5 (?) */
+#define AR5K_PHY_ANT_CTL_SWTABLE_IDLE 0x00000010 /* Switch table idle (?) */
+
/*
* PHY receiver delay register [5111+]
*/
-#define AR5K_PHY_RX_DELAY 0x9914
-#define AR5K_PHY_RX_DELAY_M 0x00003fff
+#define AR5K_PHY_RX_DELAY 0x9914 /* Register Address */
+#define AR5K_PHY_RX_DELAY_M 0x00003fff /* Mask for RX activate to receive delay (/100ns) */
+
+/*
+ * PHY max rx length register (?) [5111]
+ */
+#define AR5K_PHY_MAX_RX_LEN 0x991c
/*
- * PHY timing I(nphase) Q(adrature) control register [5111+]
+ * PHY timing register 4
+ * I(nphase)/Q(adrature) calibration register [5111+]
*/
-#define AR5K_PHY_IQ 0x9920 /* Register address */
+#define AR5K_PHY_IQ 0x9920 /* Register Address */
#define AR5K_PHY_IQ_CORR_Q_Q_COFF 0x0000001f /* Mask for q correction info */
#define AR5K_PHY_IQ_CORR_Q_I_COFF 0x000007e0 /* Mask for i correction info */
#define AR5K_PHY_IQ_CORR_Q_I_COFF_S 5
#define AR5K_PHY_IQ_CORR_ENABLE 0x00000800 /* Enable i/q correction */
-#define AR5K_PHY_IQ_CAL_NUM_LOG_MAX 0x0000f000
+#define AR5K_PHY_IQ_CAL_NUM_LOG_MAX 0x0000f000 /* Mask for max number of samples in log scale */
#define AR5K_PHY_IQ_CAL_NUM_LOG_MAX_S 12
#define AR5K_PHY_IQ_RUN 0x00010000 /* Run i/q calibration */
+#define AR5K_PHY_IQ_USE_PT_DF 0x00020000 /* Use pilot track df (?) */
+#define AR5K_PHY_IQ_EARLY_TRIG_THR 0x00200000 /* Early trigger threshold (?) (field) */
+#define AR5K_PHY_IQ_PILOT_MASK_EN 0x10000000 /* Enable pilot mask (?) */
+#define AR5K_PHY_IQ_CHAN_MASK_EN 0x20000000 /* Enable channel mask (?) */
+#define AR5K_PHY_IQ_SPUR_FILT_EN 0x40000000 /* Enable spur filter */
+#define AR5K_PHY_IQ_SPUR_RSSI_EN 0x80000000 /* Enable spur rssi */
+/*
+ * PHY timing register 5
+ * OFDM Self-correlator Cyclic RSSI threshold params
+ * (Check out bb_cycpwr_thr1 on ANI patent)
+ */
+#define AR5K_PHY_OFDM_SELFCORR 0x9924 /* Register Address */
+#define AR5K_PHY_OFDM_SELFCORR_CYPWR_THR1_EN 0x00000001 /* Enable cyclic RSSI thr 1 */
+#define AR5K_PHY_OFDM_SELFCORR_CYPWR_THR1 0x000000fe /* Mask for Cyclic RSSI threshold 1 */
+#define AR5K_PHY_OFDM_SELFCORR_CYPWR_THR3 0x00000100 /* Cyclic RSSI threshold 3 (field) (?) */
+#define AR5K_PHY_OFDM_SELFCORR_RSSI_1ATHR_EN 0x00008000 /* Enable 1A RSSI threshold (?) */
+#define AR5K_PHY_OFDM_SELFCORR_RSSI_1ATHR 0x00010000 /* 1A RSSI threshold (field) (?) */
+#define AR5K_PHY_OFDM_SELFCORR_LSCTHR_HIRSSI 0x00800000 /* Long sc threshold hi rssi (?) */
+
+/*
+ * PHY-only warm reset register
+ */
+#define AR5K_PHY_WARM_RESET 0x9928
+
+/*
+ * PHY-only control register
+ */
+#define AR5K_PHY_CTL 0x992c /* Register Address */
+#define AR5K_PHY_CTL_RX_DRAIN_RATE 0x00000001 /* RX drain rate (?) */
+#define AR5K_PHY_CTL_LATE_TX_SIG_SYM 0x00000002 /* Late tx signal symbol (?) */
+#define AR5K_PHY_CTL_GEN_SCRAMBLER 0x00000004 /* Generate scrambler */
+#define AR5K_PHY_CTL_TX_ANT_SEL 0x00000008 /* TX antenna select */
+#define AR5K_PHY_CTL_TX_ANT_STATIC 0x00000010 /* Static TX antenna */
+#define AR5K_PHY_CTL_RX_ANT_SEL 0x00000020 /* RX antenna select */
+#define AR5K_PHY_CTL_RX_ANT_STATIC 0x00000040 /* Static RX antenna */
+#define AR5K_PHY_CTL_LOW_FREQ_SLE_EN 0x00000080 /* Enable low freq sleep */
/*
* PHY PAPD probe register [5111+ (?)]
* Because it's always 0 in 5211 initialization code
*/
#define AR5K_PHY_PAPD_PROBE 0x9930
+#define AR5K_PHY_PAPD_PROBE_SH_HI_PAR 0x00000001
+#define AR5K_PHY_PAPD_PROBE_PCDAC_BIAS 0x00000002
+#define AR5K_PHY_PAPD_PROBE_COMP_GAIN 0x00000040
#define AR5K_PHY_PAPD_PROBE_TXPOWER 0x00007e00
#define AR5K_PHY_PAPD_PROBE_TXPOWER_S 9
#define AR5K_PHY_PAPD_PROBE_TX_NEXT 0x00008000
+#define AR5K_PHY_PAPD_PROBE_PREDIST_EN 0x00010000
#define AR5K_PHY_PAPD_PROBE_TYPE 0x01800000 /* [5112+] */
#define AR5K_PHY_PAPD_PROBE_TYPE_S 23
#define AR5K_PHY_PAPD_PROBE_TYPE_OFDM 0
#define AR5K_PHY_FRAME_CTL (ah->ah_version == AR5K_AR5210 ? \
AR5K_PHY_FRAME_CTL_5210 : AR5K_PHY_FRAME_CTL_5211)
/*---[5111+]---*/
-#define AR5K_PHY_FRAME_CTL_TX_CLIP 0x00000038
+#define AR5K_PHY_FRAME_CTL_TX_CLIP 0x00000038 /* Mask for tx clip (?) */
#define AR5K_PHY_FRAME_CTL_TX_CLIP_S 3
+#define AR5K_PHY_FRAME_CTL_PREP_CHINFO 0x00010000 /* Prepend chan info */
/*---[5110/5111]---*/
-#define AR5K_PHY_FRAME_CTL_TIMING_ERR 0x01000000
-#define AR5K_PHY_FRAME_CTL_PARITY_ERR 0x02000000
-#define AR5K_PHY_FRAME_CTL_ILLRATE_ERR 0x04000000 /* illegal rate */
-#define AR5K_PHY_FRAME_CTL_ILLLEN_ERR 0x08000000 /* illegal length */
+#define AR5K_PHY_FRAME_CTL_TIMING_ERR 0x01000000 /* PHY timing error */
+#define AR5K_PHY_FRAME_CTL_PARITY_ERR 0x02000000 /* Parity error */
+#define AR5K_PHY_FRAME_CTL_ILLRATE_ERR 0x04000000 /* Illegal rate */
+#define AR5K_PHY_FRAME_CTL_ILLLEN_ERR 0x08000000 /* Illegal length */
#define AR5K_PHY_FRAME_CTL_SERVICE_ERR 0x20000000
-#define AR5K_PHY_FRAME_CTL_TXURN_ERR 0x40000000 /* tx underrun */
+#define AR5K_PHY_FRAME_CTL_TXURN_ERR 0x40000000 /* TX underrun */
#define AR5K_PHY_FRAME_CTL_INI AR5K_PHY_FRAME_CTL_SERVICE_ERR | \
AR5K_PHY_FRAME_CTL_TXURN_ERR | \
AR5K_PHY_FRAME_CTL_ILLLEN_ERR | \
#define AR5K_PHY_ANT_SWITCH_TABLE_0 0x9960
#define AR5K_PHY_ANT_SWITCH_TABLE_1 0x9964
+/*
+ * PHY Noise floor threshold
+ */
+#define AR5K_PHY_NFTHRES 0x9968
+
/*
* PHY clock sleep registers [5112+]
*/
#define AR5K_PHY_SDELAY 0x99f4
#define AR5K_PHY_SDELAY_32MHZ 0x000000ff
#define AR5K_PHY_SPENDING 0x99f8
+#define AR5K_PHY_SPENDING_14 0x00000014
+#define AR5K_PHY_SPENDING_18 0x00000018
#define AR5K_PHY_SPENDING_RF5111 0x00000018
-#define AR5K_PHY_SPENDING_RF5112 0x00000014 /* <- i 've only seen this on 2425 dumps ! */
-#define AR5K_PHY_SPENDING_RF5112A 0x0000000e /* but since i only have 5112A-based chips */
-#define AR5K_PHY_SPENDING_RF5424 0x00000012 /* to test it might be also for old 5112. */
+#define AR5K_PHY_SPENDING_RF5112 0x00000014
+/* #define AR5K_PHY_SPENDING_RF5112A 0x0000000e */
+/* #define AR5K_PHY_SPENDING_RF5424 0x00000012 */
+#define AR5K_PHY_SPENDING_RF5413 0x00000014
+#define AR5K_PHY_SPENDING_RF2413 0x00000014
+#define AR5K_PHY_SPENDING_RF2425 0x00000018
/*
* Misc PHY/radio registers [5110 - 5111]
*/
-#define AR5K_BB_GAIN_BASE 0x9b00 /* BaseBand Amplifier Gain table base address */
+#define AR5K_BB_GAIN_BASE 0x9b00 /* BaseBand Amplifier Gain table base address */
#define AR5K_BB_GAIN(_n) (AR5K_BB_GAIN_BASE + ((_n) << 2))
-#define AR5K_RF_GAIN_BASE 0x9a00 /* RF Amplrifier Gain table base address */
+#define AR5K_RF_GAIN_BASE 0x9a00 /* RF Amplrifier Gain table base address */
#define AR5K_RF_GAIN(_n) (AR5K_RF_GAIN_BASE + ((_n) << 2))
/*
* PHY timing IQ calibration result register [5111+]
*/
-#define AR5K_PHY_IQRES_CAL_PWR_I 0x9c10 /* I (Inphase) power value */
-#define AR5K_PHY_IQRES_CAL_PWR_Q 0x9c14 /* Q (Quadrature) power value */
+#define AR5K_PHY_IQRES_CAL_PWR_I 0x9c10 /* I (Inphase) power value */
+#define AR5K_PHY_IQRES_CAL_PWR_Q 0x9c14 /* Q (Quadrature) power value */
#define AR5K_PHY_IQRES_CAL_CORR 0x9c18 /* I/Q Correlation */
/*
* PHY current RSSI register [5111+]
*/
-#define AR5K_PHY_CURRENT_RSSI 0x9c1c
+#define AR5K_PHY_CURRENT_RSSI 0x9c1c
+
+/*
+ * PHY RF Bus grant register (?)
+ */
+#define AR5K_PHY_RFBUS_GRANT 0x9c20
+
+/*
+ * PHY ADC test register
+ */
+#define AR5K_PHY_ADC_TEST 0x9c24
+#define AR5K_PHY_ADC_TEST_I 0x00000001
+#define AR5K_PHY_ADC_TEST_Q 0x00000200
+
+/*
+ * PHY DAC test register
+ */
+#define AR5K_PHY_DAC_TEST 0x9c28
+#define AR5K_PHY_DAC_TEST_I 0x00000001
+#define AR5K_PHY_DAC_TEST_Q 0x00000200
+
+/*
+ * PHY PTAT register (?)
+ */
+#define AR5K_PHY_PTAT 0x9c2c
+
+/*
+ * PHY Illegal TX rate register [5112+]
+ */
+#define AR5K_PHY_BAD_TX_RATE 0x9c30
+
+/*
+ * PHY SPUR Power register [5112+]
+ */
+#define AR5K_PHY_SPUR_PWR 0x9c34 /* Register Address */
+#define AR5K_PHY_SPUR_PWR_I 0x00000001 /* SPUR Power estimate for I (field) */
+#define AR5K_PHY_SPUR_PWR_Q 0x00000100 /* SPUR Power estimate for Q (field) */
+#define AR5K_PHY_SPUR_PWR_FILT 0x00010000 /* Power with SPUR removed (field) */
+
+/*
+ * PHY Channel status register [5112+] (?)
+ */
+#define AR5K_PHY_CHAN_STATUS 0x9c38
+#define AR5K_PHY_CHAN_STATUS_BT_ACT 0x00000001
+#define AR5K_PHY_CHAN_STATUS_RX_CLR_RAW 0x00000002
+#define AR5K_PHY_CHAN_STATUS_RX_CLR_MAC 0x00000004
+#define AR5K_PHY_CHAN_STATUS_RX_CLR_PAP 0x00000008
+
+/*
+ * PHY PAPD I (power?) table (?)
+ * (92! entries)
+ */
+#define AR5K_PHY_PAPD_I_BASE 0xa000
+#define AR5K_PHY_PAPD_I(_n) (AR5K_PHY_PAPD_I_BASE + ((_n) << 2))
/*
* PHY PCDAC TX power table
*/
#define AR5K_PHY_PCDAC_TXPOWER_BASE_5211 0xa180
-#define AR5K_PHY_PCDAC_TXPOWER_BASE_5413 0xa280
-#define AR5K_PHY_PCDAC_TXPOWER_BASE (ah->ah_radio >= AR5K_RF5413 ? \
- AR5K_PHY_PCDAC_TXPOWER_BASE_5413 :\
+#define AR5K_PHY_PCDAC_TXPOWER_BASE_2413 0xa280
+#define AR5K_PHY_PCDAC_TXPOWER_BASE (ah->ah_radio >= AR5K_RF2413 ? \
+ AR5K_PHY_PCDAC_TXPOWER_BASE_2413 :\
AR5K_PHY_PCDAC_TXPOWER_BASE_5211)
#define AR5K_PHY_PCDAC_TXPOWER(_n) (AR5K_PHY_PCDAC_TXPOWER_BASE + ((_n) << 2))
/*
* PHY mode register [5111+]
*/
-#define AR5K_PHY_MODE 0x0a200 /* Register address */
-#define AR5K_PHY_MODE_MOD 0x00000001 /* PHY Modulation mask*/
+#define AR5K_PHY_MODE 0x0a200 /* Register Address */
+#define AR5K_PHY_MODE_MOD 0x00000001 /* PHY Modulation bit */
#define AR5K_PHY_MODE_MOD_OFDM 0
#define AR5K_PHY_MODE_MOD_CCK 1
-#define AR5K_PHY_MODE_FREQ 0x00000002 /* Freq mode mask */
+#define AR5K_PHY_MODE_FREQ 0x00000002 /* Freq mode bit */
#define AR5K_PHY_MODE_FREQ_5GHZ 0
#define AR5K_PHY_MODE_FREQ_2GHZ 2
-#define AR5K_PHY_MODE_MOD_DYN 0x00000004 /* Dynamic OFDM/CCK mode mask [5112+] */
+#define AR5K_PHY_MODE_MOD_DYN 0x00000004 /* Enable Dynamic OFDM/CCK mode [5112+] */
#define AR5K_PHY_MODE_RAD 0x00000008 /* [5212+] */
#define AR5K_PHY_MODE_RAD_RF5111 0
#define AR5K_PHY_MODE_RAD_RF5112 8
-#define AR5K_PHY_MODE_XR 0x00000010 /* [5112+] */
+#define AR5K_PHY_MODE_XR 0x00000010 /* Enable XR mode [5112+] */
+#define AR5K_PHY_MODE_HALF_RATE 0x00000020 /* Enable Half rate (test) */
+#define AR5K_PHY_MODE_QUARTER_RATE 0x00000040 /* Enable Quarter rat (test) */
/*
* PHY CCK transmit control register [5111+ (?)]
#define AR5K_PHY_CCKTXCTL 0xa204
#define AR5K_PHY_CCKTXCTL_WORLD 0x00000000
#define AR5K_PHY_CCKTXCTL_JAPAN 0x00000010
+#define AR5K_PHY_CCKTXCTL_SCRAMBLER_DIS 0x00000001
+#define AR5K_PHY_CCKTXCTK_DAC_SCALE 0x00000004
+
+/*
+ * PHY CCK Cross-correlator Barker RSSI threshold register [5212+]
+ */
+#define AR5K_PHY_CCK_CROSSCORR 0xa208
+#define AR5K_PHY_CCK_CROSSCORR_WEAK_SIG_THR 0x0000000f
+#define AR5K_PHY_CCK_CROSSCORR_WEAK_SIG_THR_S 0
/*
* PHY 2GHz gain register [5111+]
projects / linux-2.6 / commitdiff