dbg("%s: change to speed %d\n", __FUNCTION__, speed);
if ((rc = p_slot->hpc_ops->set_bus_speed_mode(p_slot, speed))) {
- err("%s: Issue of set bus speed mode command failed\n", __FUNCTION__);
+ err("%s: Issue of set bus speed mode command failed\n",
+ __FUNCTION__);
return WRONG_BUS_FREQUENCY;
}
return rc;
enum pci_bus_speed msp)
{
int rc = 0;
-
- if (flag != 0) { /* Other slots on the same bus are occupied */
- if ( asp < bsp ) {
- err("%s: speed of bus %x and adapter %x mismatch\n", __FUNCTION__, bsp, asp);
- return WRONG_BUS_FREQUENCY;
+
+ /*
+ * If other slots on the same bus are occupied, we cannot
+ * change the bus speed.
+ */
+ if (flag) {
+ if (asp < bsp) {
+ err("%s: speed of bus %x and adapter %x mismatch\n",
+ __FUNCTION__, bsp, asp);
+ rc = WRONG_BUS_FREQUENCY;
}
+ return rc;
+ }
+
+ if (asp < msp) {
+ if (bsp != asp)
+ rc = change_bus_speed(ctrl, pslot, asp);
} else {
- /* Other slots on the same bus are empty */
- if (msp == bsp) {
- /* if adapter_speed >= bus_speed, do nothing */
- if (asp < bsp) {
- /*
- * Try to lower bus speed to accommodate the adapter if other slots
- * on the same controller are empty
- */
- if ((rc = change_bus_speed(ctrl, pslot, asp)))
- return rc;
- }
- } else {
- if (asp < msp) {
- if ((rc = change_bus_speed(ctrl, pslot, asp)))
- return rc;
- } else {
- if ((rc = change_bus_speed(ctrl, pslot, msp)))
- return rc;
- }
- }
+ if (bsp != msp)
+ rc = change_bus_speed(ctrl, pslot, msp);
}
return rc;
}
u8 hp_slot;
u8 slots_not_empty = 0;
int rc = 0;
- enum pci_bus_speed adapter_speed, bus_speed, max_bus_speed;
- u8 pi, mode;
+ enum pci_bus_speed asp, bsp, msp;
struct controller *ctrl = p_slot->ctrl;
hp_slot = p_slot->device - ctrl->slot_device_offset;
}
}
- rc = p_slot->hpc_ops->get_adapter_speed(p_slot, &adapter_speed);
- /* 0 = PCI 33Mhz, 1 = PCI 66 Mhz, 2 = PCI-X 66 PA, 4 = PCI-X 66 ECC, */
- /* 5 = PCI-X 133 PA, 7 = PCI-X 133 ECC, 0xa = PCI-X 133 Mhz 266, */
- /* 0xd = PCI-X 133 Mhz 533 */
- /* This encoding is different from the one used in cur_bus_speed & */
- /* max_bus_speed */
-
- if (rc || adapter_speed == PCI_SPEED_UNKNOWN) {
- err("%s: Can't get adapter speed or bus mode mismatch\n", __FUNCTION__);
+ rc = p_slot->hpc_ops->get_adapter_speed(p_slot, &asp);
+ if (rc) {
+ err("%s: Can't get adapter speed or bus mode mismatch\n",
+ __FUNCTION__);
return WRONG_BUS_FREQUENCY;
}
- rc = p_slot->hpc_ops->get_cur_bus_speed(p_slot, &bus_speed);
- if (rc || bus_speed == PCI_SPEED_UNKNOWN) {
+ rc = p_slot->hpc_ops->get_cur_bus_speed(p_slot, &bsp);
+ if (rc) {
err("%s: Can't get bus operation speed\n", __FUNCTION__);
return WRONG_BUS_FREQUENCY;
}
- rc = p_slot->hpc_ops->get_max_bus_speed(p_slot, &max_bus_speed);
- if (rc || max_bus_speed == PCI_SPEED_UNKNOWN) {
+ rc = p_slot->hpc_ops->get_max_bus_speed(p_slot, &msp);
+ if (rc) {
err("%s: Can't get max bus operation speed\n", __FUNCTION__);
- max_bus_speed = bus_speed;
- }
-
- if ((rc = p_slot->hpc_ops->get_prog_int(p_slot, &pi))) {
- err("%s: Can't get controller programming interface, set it to 1\n", __FUNCTION__);
- pi = 1;
+ msp = bsp;
}
/* Check if there are other slots or devices on the same bus */
if (!list_empty(&ctrl->pci_dev->subordinate->devices))
slots_not_empty = 1;
- dbg("%s: slots_not_empty %d, pi %d\n", __FUNCTION__,
- slots_not_empty, pi);
- dbg("adapter_speed %d, bus_speed %d, max_bus_speed %d\n",
- adapter_speed, bus_speed, max_bus_speed);
-
- if (pi == 2) {
- dbg("%s: In PI = %d\n", __FUNCTION__, pi);
- if ((rc = p_slot->hpc_ops->get_mode1_ECC_cap(p_slot, &mode))) {
- err("%s: Can't get Mode1_ECC, set mode to 0\n", __FUNCTION__);
- mode = 0;
- }
+ dbg("%s: slots_not_empty %d, adapter_speed %d, bus_speed %d, "
+ "max_bus_speed %d\n", __FUNCTION__, slots_not_empty, asp,
+ bsp, msp);
- switch (adapter_speed) {
- case PCI_SPEED_133MHz_PCIX_533:
- case PCI_SPEED_133MHz_PCIX_266:
- if ((bus_speed != adapter_speed) &&
- ((rc = fix_bus_speed(ctrl, p_slot, slots_not_empty, adapter_speed, bus_speed, max_bus_speed))))
- return rc;
- break;
- case PCI_SPEED_133MHz_PCIX_ECC:
- case PCI_SPEED_133MHz_PCIX:
- if (mode) { /* Bus - Mode 1 ECC */
- if ((bus_speed != 0x7) &&
- ((rc = fix_bus_speed(ctrl, p_slot, slots_not_empty, adapter_speed, bus_speed, max_bus_speed))))
- return rc;
- } else {
- if ((bus_speed != 0x4) &&
- ((rc = fix_bus_speed(ctrl, p_slot, slots_not_empty, adapter_speed, bus_speed, max_bus_speed))))
- return rc;
- }
- break;
- case PCI_SPEED_66MHz_PCIX_ECC:
- case PCI_SPEED_66MHz_PCIX:
- if (mode) { /* Bus - Mode 1 ECC */
- if ((bus_speed != 0x5) &&
- ((rc = fix_bus_speed(ctrl, p_slot, slots_not_empty, adapter_speed, bus_speed, max_bus_speed))))
- return rc;
- } else {
- if ((bus_speed != 0x2) &&
- ((rc = fix_bus_speed(ctrl, p_slot, slots_not_empty, adapter_speed, bus_speed, max_bus_speed))))
- return rc;
- }
- break;
- case PCI_SPEED_66MHz:
- if ((bus_speed != 0x1) &&
- ((rc = fix_bus_speed(ctrl, p_slot, slots_not_empty, adapter_speed, bus_speed, max_bus_speed))))
- return rc;
- break;
- case PCI_SPEED_33MHz:
- if (bus_speed > 0x0) {
- if (slots_not_empty == 0) {
- if ((rc = change_bus_speed(ctrl, p_slot, adapter_speed)))
- return rc;
- } else {
- err("%s: speed of bus %x and adapter %x mismatch\n", __FUNCTION__, bus_speed, adapter_speed);
- return WRONG_BUS_FREQUENCY;
- }
- }
- break;
- default:
- err("%s: speed of bus %x and adapter %x mismatch\n", __FUNCTION__, bus_speed, adapter_speed);
- return WRONG_BUS_FREQUENCY;
- }
- } else {
- /* If adpater_speed == bus_speed, nothing to do here */
- dbg("%s: In PI = %d\n", __FUNCTION__, pi);
- if ((adapter_speed != bus_speed) &&
- ((rc = fix_bus_speed(ctrl, p_slot, slots_not_empty, adapter_speed, bus_speed, max_bus_speed))))
- return rc;
- }
+ rc = fix_bus_speed(ctrl, p_slot, slots_not_empty, asp, bsp, msp);
+ if (rc)
+ return rc;
/* turn on board, blink green LED, turn off Amber LED */
if ((rc = p_slot->hpc_ops->slot_enable(p_slot))) {
#define SLOT_100MHZ_PCIX_533 0x0f000000
#define SLOT_133MHZ_PCIX_533 0xf0000000
-
-/* Secondary Bus Configuration Register */
-/* For PI = 1, Bits 0 to 2 have been encoded as follows to show current bus speed/mode */
-#define PCI_33MHZ 0x0
-#define PCI_66MHZ 0x1
-#define PCIX_66MHZ 0x2
-#define PCIX_100MHZ 0x3
-#define PCIX_133MHZ 0x4
-
-/* For PI = 2, Bits 0 to 3 have been encoded as follows to show current bus speed/mode */
-#define PCI_33MHZ 0x0
-#define PCI_66MHZ 0x1
-#define PCIX_66MHZ 0x2
-#define PCIX_100MHZ 0x3
-#define PCIX_133MHZ 0x4
-#define PCIX_66MHZ_ECC 0x5
-#define PCIX_100MHZ_ECC 0x6
-#define PCIX_133MHZ_ECC 0x7
-#define PCIX_66MHZ_266 0x9
-#define PCIX_100MHZ_266 0xa
-#define PCIX_133MHZ_266 0xb
-#define PCIX_66MHZ_533 0x11
-#define PCIX_100MHZ_533 0x12
-#define PCIX_133MHZ_533 0x13
-
/* Slot Configuration */
#define SLOT_NUM 0x0000001F
#define FIRST_DEV_NUM 0x00001F00
static int hpc_get_adapter_speed(struct slot *slot, enum pci_bus_speed *value)
{
- struct php_ctlr_state_s *php_ctlr = slot->ctrl->hpc_ctlr_handle;
- u32 slot_reg;
- u16 slot_status, sec_bus_status;
- u8 m66_cap, pcix_cap, pi;
int retval = 0;
+ struct php_ctlr_state_s *php_ctlr = slot->ctrl->hpc_ctlr_handle;
+ u32 slot_reg = readl(php_ctlr->creg + SLOT1 + 4 * slot->hp_slot);
+ u8 pcix_cap = (slot_reg >> 12) & 7;
+ u8 m66_cap = (slot_reg >> 9) & 1;
DBG_ENTER_ROUTINE
- if (!slot->ctrl->hpc_ctlr_handle) {
- err("%s: Invalid HPC controller handle!\n", __FUNCTION__);
- return -1;
- }
-
- if (slot->hp_slot >= php_ctlr->num_slots) {
- err("%s: Invalid HPC slot number!\n", __FUNCTION__);
- return -1;
- }
-
- pi = readb(php_ctlr->creg + PROG_INTERFACE);
- slot_reg = readl(php_ctlr->creg + SLOT1 + 4*(slot->hp_slot));
- dbg("%s: pi = %d, slot_reg = %x\n", __FUNCTION__, pi, slot_reg);
- slot_status = (u16) slot_reg;
- dbg("%s: slot_status = %x\n", __FUNCTION__, slot_status);
- sec_bus_status = readw(php_ctlr->creg + SEC_BUS_CONFIG);
-
- pcix_cap = (u8) ((slot_status & 0x3000) >> 12);
- dbg("%s: pcix_cap = %x\n", __FUNCTION__, pcix_cap);
- m66_cap = (u8) ((slot_status & 0x0200) >> 9);
- dbg("%s: m66_cap = %x\n", __FUNCTION__, m66_cap);
+ dbg("%s: slot_reg = %x, pcix_cap = %x, m66_cap = %x\n",
+ __FUNCTION__, slot_reg, pcix_cap, m66_cap);
-
- if (pi == 2) {
- switch (pcix_cap) {
- case 0:
- *value = m66_cap ? PCI_SPEED_66MHz : PCI_SPEED_33MHz;
- break;
- case 1:
- *value = PCI_SPEED_66MHz_PCIX;
- break;
- case 3:
- *value = PCI_SPEED_133MHz_PCIX;
- break;
- case 4:
- *value = PCI_SPEED_133MHz_PCIX_266;
- break;
- case 5:
- *value = PCI_SPEED_133MHz_PCIX_533;
- break;
- case 2: /* Reserved */
- default:
- *value = PCI_SPEED_UNKNOWN;
- retval = -ENODEV;
- break;
- }
- } else {
- switch (pcix_cap) {
- case 0:
- *value = m66_cap ? PCI_SPEED_66MHz : PCI_SPEED_33MHz;
- break;
- case 1:
- *value = PCI_SPEED_66MHz_PCIX;
- break;
- case 3:
- *value = PCI_SPEED_133MHz_PCIX;
- break;
- case 2: /* Reserved */
- default:
- *value = PCI_SPEED_UNKNOWN;
- retval = -ENODEV;
- break;
- }
+ switch (pcix_cap) {
+ case 0x0:
+ *value = m66_cap ? PCI_SPEED_66MHz : PCI_SPEED_33MHz;
+ break;
+ case 0x1:
+ *value = PCI_SPEED_66MHz_PCIX;
+ break;
+ case 0x3:
+ *value = PCI_SPEED_133MHz_PCIX;
+ break;
+ case 0x4:
+ *value = PCI_SPEED_133MHz_PCIX_266;
+ break;
+ case 0x5:
+ *value = PCI_SPEED_133MHz_PCIX_533;
+ break;
+ case 0x2:
+ default:
+ *value = PCI_SPEED_UNKNOWN;
+ retval = -ENODEV;
+ break;
}
dbg("Adapter speed = %d\n", *value);
-
DBG_LEAVE_ROUTINE
return retval;
}
static int hpc_set_bus_speed_mode(struct slot * slot, enum pci_bus_speed value)
{
- u8 slot_cmd;
- u8 pi;
- int retval = 0;
+ int retval;
struct php_ctlr_state_s *php_ctlr = slot->ctrl->hpc_ctlr_handle;
+ u8 pi, cmd;
DBG_ENTER_ROUTINE
-
- if (!slot->ctrl->hpc_ctlr_handle) {
- err("%s: Invalid HPC controller handle!\n", __FUNCTION__);
- return -1;
- }
pi = readb(php_ctlr->creg + PROG_INTERFACE);
-
- if (pi == 1) {
- switch (value) {
- case 0:
- slot_cmd = SETA_PCI_33MHZ;
- break;
- case 1:
- slot_cmd = SETA_PCI_66MHZ;
- break;
- case 2:
- slot_cmd = SETA_PCIX_66MHZ;
- break;
- case 3:
- slot_cmd = SETA_PCIX_100MHZ;
- break;
- case 4:
- slot_cmd = SETA_PCIX_133MHZ;
- break;
- default:
- slot_cmd = PCI_SPEED_UNKNOWN;
- retval = -ENODEV;
- return retval;
- }
- } else {
- switch (value) {
- case 0:
- slot_cmd = SETB_PCI_33MHZ;
- break;
- case 1:
- slot_cmd = SETB_PCI_66MHZ;
- break;
- case 2:
- slot_cmd = SETB_PCIX_66MHZ_PM;
- break;
- case 3:
- slot_cmd = SETB_PCIX_100MHZ_PM;
- break;
- case 4:
- slot_cmd = SETB_PCIX_133MHZ_PM;
- break;
- case 5:
- slot_cmd = SETB_PCIX_66MHZ_EM;
- break;
- case 6:
- slot_cmd = SETB_PCIX_100MHZ_EM;
- break;
- case 7:
- slot_cmd = SETB_PCIX_133MHZ_EM;
- break;
- case 8:
- slot_cmd = SETB_PCIX_66MHZ_266;
- break;
- case 0x9:
- slot_cmd = SETB_PCIX_100MHZ_266;
- break;
- case 0xa:
- slot_cmd = SETB_PCIX_133MHZ_266;
- break;
- case 0xb:
- slot_cmd = SETB_PCIX_66MHZ_533;
- break;
- case 0xc:
- slot_cmd = SETB_PCIX_100MHZ_533;
- break;
- case 0xd:
- slot_cmd = SETB_PCIX_133MHZ_533;
- break;
- default:
- slot_cmd = PCI_SPEED_UNKNOWN;
- retval = -ENODEV;
- return retval;
- }
+ if ((pi == 1) && (value > PCI_SPEED_133MHz_PCIX))
+ return -EINVAL;
+ switch (value) {
+ case PCI_SPEED_33MHz:
+ cmd = SETA_PCI_33MHZ;
+ break;
+ case PCI_SPEED_66MHz:
+ cmd = SETA_PCI_66MHZ;
+ break;
+ case PCI_SPEED_66MHz_PCIX:
+ cmd = SETA_PCIX_66MHZ;
+ break;
+ case PCI_SPEED_100MHz_PCIX:
+ cmd = SETA_PCIX_100MHZ;
+ break;
+ case PCI_SPEED_133MHz_PCIX:
+ cmd = SETA_PCIX_133MHZ;
+ break;
+ case PCI_SPEED_66MHz_PCIX_ECC:
+ cmd = SETB_PCIX_66MHZ_EM;
+ break;
+ case PCI_SPEED_100MHz_PCIX_ECC:
+ cmd = SETB_PCIX_100MHZ_EM;
+ break;
+ case PCI_SPEED_133MHz_PCIX_ECC:
+ cmd = SETB_PCIX_133MHZ_EM;
+ break;
+ case PCI_SPEED_66MHz_PCIX_266:
+ cmd = SETB_PCIX_66MHZ_266;
+ break;
+ case PCI_SPEED_100MHz_PCIX_266:
+ cmd = SETB_PCIX_100MHZ_266;
+ break;
+ case PCI_SPEED_133MHz_PCIX_266:
+ cmd = SETB_PCIX_133MHZ_266;
+ break;
+ case PCI_SPEED_66MHz_PCIX_533:
+ cmd = SETB_PCIX_66MHZ_533;
+ break;
+ case PCI_SPEED_100MHz_PCIX_533:
+ cmd = SETB_PCIX_100MHZ_533;
+ break;
+ case PCI_SPEED_133MHz_PCIX_533:
+ cmd = SETB_PCIX_133MHZ_533;
+ break;
+ default:
+ return -EINVAL;
}
- retval = shpc_write_cmd(slot, 0, slot_cmd);
- if (retval) {
+
+ retval = shpc_write_cmd(slot, 0, cmd);
+ if (retval)
err("%s: Write command failed!\n", __FUNCTION__);
- return -1;
- }
DBG_LEAVE_ROUTINE
return retval;
static int hpc_get_max_bus_speed (struct slot *slot, enum pci_bus_speed *value)
{
+ int retval = 0;
struct php_ctlr_state_s *php_ctlr = slot->ctrl->hpc_ctlr_handle;
enum pci_bus_speed bus_speed = PCI_SPEED_UNKNOWN;
- int retval = 0;
- u8 pi;
- u32 slot_avail1, slot_avail2;
+ u8 pi = readb(php_ctlr->creg + PROG_INTERFACE);
+ u32 slot_avail1 = readl(php_ctlr->creg + SLOT_AVAIL1);
+ u32 slot_avail2 = readl(php_ctlr->creg + SLOT_AVAIL2);
DBG_ENTER_ROUTINE
- if (!slot->ctrl->hpc_ctlr_handle) {
- err("%s: Invalid HPC controller handle!\n", __FUNCTION__);
- return -1;
- }
-
- if (slot->hp_slot >= php_ctlr->num_slots) {
- err("%s: Invalid HPC slot number!\n", __FUNCTION__);
- return -1;
- }
-
- pi = readb(php_ctlr->creg + PROG_INTERFACE);
- slot_avail1 = readl(php_ctlr->creg + SLOT_AVAIL1);
- slot_avail2 = readl(php_ctlr->creg + SLOT_AVAIL2);
-
if (pi == 2) {
if (slot_avail2 & SLOT_133MHZ_PCIX_533)
- bus_speed = PCIX_133MHZ_533;
+ bus_speed = PCI_SPEED_133MHz_PCIX_533;
else if (slot_avail2 & SLOT_100MHZ_PCIX_533)
- bus_speed = PCIX_100MHZ_533;
+ bus_speed = PCI_SPEED_100MHz_PCIX_533;
else if (slot_avail2 & SLOT_66MHZ_PCIX_533)
- bus_speed = PCIX_66MHZ_533;
+ bus_speed = PCI_SPEED_66MHz_PCIX_533;
else if (slot_avail2 & SLOT_133MHZ_PCIX_266)
- bus_speed = PCIX_133MHZ_266;
+ bus_speed = PCI_SPEED_133MHz_PCIX_266;
else if (slot_avail2 & SLOT_100MHZ_PCIX_266)
- bus_speed = PCIX_100MHZ_266;
+ bus_speed = PCI_SPEED_100MHz_PCIX_266;
else if (slot_avail2 & SLOT_66MHZ_PCIX_266)
- bus_speed = PCIX_66MHZ_266;
- else if (slot_avail1 & SLOT_133MHZ_PCIX)
- bus_speed = PCIX_133MHZ;
- else if (slot_avail1 & SLOT_100MHZ_PCIX)
- bus_speed = PCIX_100MHZ;
- else if (slot_avail1 & SLOT_66MHZ_PCIX)
- bus_speed = PCIX_66MHZ;
- else if (slot_avail2 & SLOT_66MHZ)
- bus_speed = PCI_66MHZ;
- else if (slot_avail1 & SLOT_33MHZ)
- bus_speed = PCI_33MHZ;
- else bus_speed = PCI_SPEED_UNKNOWN;
- } else {
+ bus_speed = PCI_SPEED_66MHz_PCIX_266;
+ }
+
+ if (bus_speed == PCI_SPEED_UNKNOWN) {
if (slot_avail1 & SLOT_133MHZ_PCIX)
- bus_speed = PCIX_133MHZ;
+ bus_speed = PCI_SPEED_133MHz_PCIX;
else if (slot_avail1 & SLOT_100MHZ_PCIX)
- bus_speed = PCIX_100MHZ;
+ bus_speed = PCI_SPEED_100MHz_PCIX;
else if (slot_avail1 & SLOT_66MHZ_PCIX)
- bus_speed = PCIX_66MHZ;
+ bus_speed = PCI_SPEED_66MHz_PCIX;
else if (slot_avail2 & SLOT_66MHZ)
- bus_speed = PCI_66MHZ;
+ bus_speed = PCI_SPEED_66MHz;
else if (slot_avail1 & SLOT_33MHZ)
- bus_speed = PCI_33MHZ;
- else bus_speed = PCI_SPEED_UNKNOWN;
+ bus_speed = PCI_SPEED_33MHz;
+ else
+ retval = -ENODEV;
}
*value = bus_speed;
static int hpc_get_cur_bus_speed (struct slot *slot, enum pci_bus_speed *value)
{
+ int retval = 0;
struct php_ctlr_state_s *php_ctlr = slot->ctrl->hpc_ctlr_handle;
enum pci_bus_speed bus_speed = PCI_SPEED_UNKNOWN;
- u16 sec_bus_status;
- int retval = 0;
- u8 pi;
+ u16 sec_bus_reg = readw(php_ctlr->creg + SEC_BUS_CONFIG);
+ u8 pi = readb(php_ctlr->creg + PROG_INTERFACE);
+ u8 speed_mode = (pi == 2) ? (sec_bus_reg & 0xF) : (sec_bus_reg & 0x7);
DBG_ENTER_ROUTINE
- if (!slot->ctrl->hpc_ctlr_handle) {
- err("%s: Invalid HPC controller handle!\n", __FUNCTION__);
- return -1;
- }
-
- if (slot->hp_slot >= php_ctlr->num_slots) {
- err("%s: Invalid HPC slot number!\n", __FUNCTION__);
- return -1;
+ if ((pi == 1) && (speed_mode > 4)) {
+ *value = PCI_SPEED_UNKNOWN;
+ return -ENODEV;
}
- pi = readb(php_ctlr->creg + PROG_INTERFACE);
- sec_bus_status = readw(php_ctlr->creg + SEC_BUS_CONFIG);
-
- if (pi == 2) {
- switch (sec_bus_status & 0x000f) {
- case 0:
- bus_speed = PCI_SPEED_33MHz;
- break;
- case 1:
- bus_speed = PCI_SPEED_66MHz;
- break;
- case 2:
- bus_speed = PCI_SPEED_66MHz_PCIX;
- break;
- case 3:
- bus_speed = PCI_SPEED_100MHz_PCIX;
- break;
- case 4:
- bus_speed = PCI_SPEED_133MHz_PCIX;
- break;
- case 5:
- bus_speed = PCI_SPEED_66MHz_PCIX_ECC;
- break;
- case 6:
- bus_speed = PCI_SPEED_100MHz_PCIX_ECC;
- break;
- case 7:
- bus_speed = PCI_SPEED_133MHz_PCIX_ECC;
- break;
- case 8:
- bus_speed = PCI_SPEED_66MHz_PCIX_266;
- break;
- case 9:
- bus_speed = PCI_SPEED_100MHz_PCIX_266;
- break;
- case 0xa:
- bus_speed = PCI_SPEED_133MHz_PCIX_266;
- break;
- case 0xb:
- bus_speed = PCI_SPEED_66MHz_PCIX_533;
- break;
- case 0xc:
- bus_speed = PCI_SPEED_100MHz_PCIX_533;
- break;
- case 0xd:
- bus_speed = PCI_SPEED_133MHz_PCIX_533;
- break;
- case 0xe:
- case 0xf:
- default:
- bus_speed = PCI_SPEED_UNKNOWN;
- break;
- }
- } else {
- /* In the case where pi is undefined, default it to 1 */
- switch (sec_bus_status & 0x0007) {
- case 0:
- bus_speed = PCI_SPEED_33MHz;
- break;
- case 1:
- bus_speed = PCI_SPEED_66MHz;
- break;
- case 2:
- bus_speed = PCI_SPEED_66MHz_PCIX;
- break;
- case 3:
- bus_speed = PCI_SPEED_100MHz_PCIX;
- break;
- case 4:
- bus_speed = PCI_SPEED_133MHz_PCIX;
- break;
- case 5:
- bus_speed = PCI_SPEED_UNKNOWN; /* Reserved */
- break;
- case 6:
- bus_speed = PCI_SPEED_UNKNOWN; /* Reserved */
- break;
- case 7:
- bus_speed = PCI_SPEED_UNKNOWN; /* Reserved */
- break;
- default:
- bus_speed = PCI_SPEED_UNKNOWN;
- break;
- }
+ switch (speed_mode) {
+ case 0x0:
+ *value = PCI_SPEED_33MHz;
+ break;
+ case 0x1:
+ *value = PCI_SPEED_66MHz;
+ break;
+ case 0x2:
+ *value = PCI_SPEED_66MHz_PCIX;
+ break;
+ case 0x3:
+ *value = PCI_SPEED_100MHz_PCIX;
+ break;
+ case 0x4:
+ *value = PCI_SPEED_133MHz_PCIX;
+ break;
+ case 0x5:
+ *value = PCI_SPEED_66MHz_PCIX_ECC;
+ break;
+ case 0x6:
+ *value = PCI_SPEED_100MHz_PCIX_ECC;
+ break;
+ case 0x7:
+ *value = PCI_SPEED_133MHz_PCIX_ECC;
+ break;
+ case 0x8:
+ *value = PCI_SPEED_66MHz_PCIX_266;
+ break;
+ case 0x9:
+ *value = PCI_SPEED_100MHz_PCIX_266;
+ break;
+ case 0xa:
+ *value = PCI_SPEED_133MHz_PCIX_266;
+ break;
+ case 0xb:
+ *value = PCI_SPEED_66MHz_PCIX_533;
+ break;
+ case 0xc:
+ *value = PCI_SPEED_100MHz_PCIX_533;
+ break;
+ case 0xd:
+ *value = PCI_SPEED_133MHz_PCIX_533;
+ break;
+ default:
+ *value = PCI_SPEED_UNKNOWN;
+ retval = -ENODEV;
+ break;
}
- *value = bus_speed;
dbg("Current bus speed = %d\n", bus_speed);
DBG_LEAVE_ROUTINE
return retval;
projects / linux-2.6 / commitdiff