X-Git-Url: https://err.no/cgi-bin/gitweb.cgi?a=blobdiff_plain;f=drivers%2Fusb%2Fserial%2Fcypress_m8.c;h=012e63e05806076b06a42dc1d3d592fa45fc0fce;hb=03d661d3d7dd2c20330d775c13157419049f1617;hp=d165f42d560d6282751c6f81075eced95994341c;hpb=c79bea07ec4d3ef087962699fe8b2f6dc5ca7754;p=linux-2.6 diff --git a/drivers/usb/serial/cypress_m8.c b/drivers/usb/serial/cypress_m8.c index d165f42d56..012e63e058 100644 --- a/drivers/usb/serial/cypress_m8.c +++ b/drivers/usb/serial/cypress_m8.c @@ -16,6 +16,14 @@ * See http://geocities.com/i0xox0i for information on this driver and the * earthmate usb device. * + * Lonnie Mendez + * 4-29-2005 + * Fixed problem where setting or retreiving the serial config would fail with + * EPIPE. Removed CRTS toggling so the driver behaves more like other usbserial + * adapters. Issued new interval of 1ms instead of the default 10ms. As a + * result, transfer speed has been substantially increased. From avg. 850bps to + * avg. 3300bps. initial termios has also been modified. Cleaned up code and + * formatting issues so it is more readable. Replaced the C++ style comments. * * Lonnie Mendez * 12-15-2004 @@ -32,12 +40,6 @@ * 10-2003 * Driver first released. * - * - * Long Term TODO: - * Improve transfer speeds - both read/write are somewhat slow - * at this point. - * Improve debugging. Show modem line status with debug output and - * implement filtering for certain data as a module parameter. */ /* Thanks to Neil Whelchel for writing the first cypress m8 implementation for linux. */ @@ -72,11 +74,12 @@ static int debug; #endif static int stats; +static int interval; /* * Version Information */ -#define DRIVER_VERSION "v1.08" +#define DRIVER_VERSION "v1.09" #define DRIVER_AUTHOR "Lonnie Mendez , Neil Whelchel " #define DRIVER_DESC "Cypress USB to Serial Driver" @@ -86,6 +89,7 @@ static int stats; static struct usb_device_id id_table_earthmate [] = { { USB_DEVICE(VENDOR_ID_DELORME, PRODUCT_ID_EARTHMATEUSB) }, + { USB_DEVICE(VENDOR_ID_DELORME, PRODUCT_ID_EARTHMATEUSB_LT20) }, { } /* Terminating entry */ }; @@ -96,6 +100,7 @@ static struct usb_device_id id_table_cyphidcomrs232 [] = { static struct usb_device_id id_table_combined [] = { { USB_DEVICE(VENDOR_ID_DELORME, PRODUCT_ID_EARTHMATEUSB) }, + { USB_DEVICE(VENDOR_ID_DELORME, PRODUCT_ID_EARTHMATEUSB_LT20) }, { USB_DEVICE(VENDOR_ID_CYPRESS, PRODUCT_ID_CYPHIDCOM) }, { } /* Terminating entry */ }; @@ -130,7 +135,6 @@ struct cypress_private { char prev_status, diff_status; /* used for TIOCMIWAIT */ /* we pass a pointer to this as the arguement sent to cypress_set_termios old_termios */ struct termios tmp_termios; /* stores the old termios settings */ - char calledfromopen; /* used when issuing lines on open - fixes rts drop bug */ }; /* write buffer structure */ @@ -168,10 +172,8 @@ static void cypress_buf_free(struct cypress_buf *cb); static void cypress_buf_clear(struct cypress_buf *cb); static unsigned int cypress_buf_data_avail(struct cypress_buf *cb); static unsigned int cypress_buf_space_avail(struct cypress_buf *cb); -static unsigned int cypress_buf_put(struct cypress_buf *cb, const char *buf, - unsigned int count); -static unsigned int cypress_buf_get(struct cypress_buf *cb, char *buf, - unsigned int count); +static unsigned int cypress_buf_put(struct cypress_buf *cb, const char *buf, unsigned int count); +static unsigned int cypress_buf_get(struct cypress_buf *cb, char *buf, unsigned int count); static struct usb_serial_device_type cypress_earthmate_device = { @@ -234,14 +236,13 @@ static struct usb_serial_device_type cypress_hidcom_device = { *****************************************************************************/ -/* This function can either set or retreive the current serial line settings */ +/* This function can either set or retrieve the current serial line settings */ static int cypress_serial_control (struct usb_serial_port *port, unsigned baud_mask, int data_bits, int stop_bits, int parity_enable, int parity_type, int reset, int cypress_request_type) { - int i, n_baud_rate = 0, retval = 0; + int new_baudrate = 0, retval = 0, tries = 0; struct cypress_private *priv; - __u8 feature_buffer[5]; - __u8 config; + __u8 feature_buffer[8]; unsigned long flags; dbg("%s", __FUNCTION__); @@ -256,7 +257,8 @@ static int cypress_serial_control (struct usb_serial_port *port, unsigned baud_m * of 57600bps (I have no idea whether DeLorme chose to use the general purpose * firmware or not), if you need to modify this speed setting for your own * project please add your own chiptype and modify the code likewise. The - * Cypress HID->COM device will work successfully up to 115200bps. + * Cypress HID->COM device will work successfully up to 115200bps (but the + * actual throughput is around 3kBps). */ if (baud_mask != priv->cbr_mask) { dbg("%s - baud rate is changing", __FUNCTION__); @@ -265,109 +267,114 @@ static int cypress_serial_control (struct usb_serial_port *port, unsigned baud_m * but are not used with NMEA and SiRF protocols */ if ( (baud_mask == B300) || (baud_mask == B600) ) { - err("%s - failed setting baud rate, unsupported speed (default to 4800)", + err("%s - failed setting baud rate, unsupported speed", __FUNCTION__); - n_baud_rate = 4800; - } else if ( (n_baud_rate = mask_to_rate(baud_mask)) == -1) { - err("%s - failed setting baud rate, unsupported speed (default to 4800)", + new_baudrate = priv->baud_rate; + } else if ( (new_baudrate = mask_to_rate(baud_mask)) == -1) { + err("%s - failed setting baud rate, unsupported speed", __FUNCTION__); - n_baud_rate = 4800; + new_baudrate = priv->baud_rate; } } else if (priv->chiptype == CT_CYPHIDCOM) { - if ( (n_baud_rate = mask_to_rate(baud_mask)) == -1) { - err("%s - failed setting baud rate, unsupported speed (default to 4800)", + if ( (new_baudrate = mask_to_rate(baud_mask)) == -1) { + err("%s - failed setting baud rate, unsupported speed", __FUNCTION__); - n_baud_rate = 4800; + new_baudrate = priv->baud_rate; } } else if (priv->chiptype == CT_GENERIC) { - if ( (n_baud_rate = mask_to_rate(baud_mask)) == -1) { - err("%s - failed setting baud rate, unsupported speed (default to 4800)", + if ( (new_baudrate = mask_to_rate(baud_mask)) == -1) { + err("%s - failed setting baud rate, unsupported speed", __FUNCTION__); - n_baud_rate = 4800; + new_baudrate = priv->baud_rate; } } else { - info("%s - please define your chiptype, using 4800bps default", __FUNCTION__); - n_baud_rate = 4800; + info("%s - please define your chiptype", __FUNCTION__); + new_baudrate = priv->baud_rate; } } else { /* baud rate not changing, keep the old */ - n_baud_rate = priv->baud_rate; + new_baudrate = priv->baud_rate; } - dbg("%s - baud rate is being sent as %d", __FUNCTION__, n_baud_rate); - + dbg("%s - baud rate is being sent as %d", __FUNCTION__, new_baudrate); - /* - * This algorithm accredited to Jiang Jay Zhang... thanks for all the help! - */ - for (i = 0; i < 4; ++i) { - feature_buffer[i] = ( n_baud_rate >> (i*8) & 0xFF ); - } + memset(feature_buffer, 0, 8); + /* fill the feature_buffer with new configuration */ + *((u_int32_t *)feature_buffer) = new_baudrate; - config = 0; // reset config byte - config |= data_bits; // assign data bits in 2 bit space ( max 3 ) + feature_buffer[4] |= data_bits; /* assign data bits in 2 bit space ( max 3 ) */ /* 1 bit gap */ - config |= (stop_bits << 3); // assign stop bits in 1 bit space - config |= (parity_enable << 4); // assign parity flag in 1 bit space - config |= (parity_type << 5); // assign parity type in 1 bit space + feature_buffer[4] |= (stop_bits << 3); /* assign stop bits in 1 bit space */ + feature_buffer[4] |= (parity_enable << 4); /* assign parity flag in 1 bit space */ + feature_buffer[4] |= (parity_type << 5); /* assign parity type in 1 bit space */ /* 1 bit gap */ - config |= (reset << 7); // assign reset at end of byte, 1 bit space - - feature_buffer[4] = config; + feature_buffer[4] |= (reset << 7); /* assign reset at end of byte, 1 bit space */ dbg("%s - device is being sent this feature report:", __FUNCTION__); dbg("%s - %02X - %02X - %02X - %02X - %02X", __FUNCTION__, feature_buffer[0], feature_buffer[1], feature_buffer[2], feature_buffer[3], feature_buffer[4]); + do { retval = usb_control_msg (port->serial->dev, usb_sndctrlpipe(port->serial->dev, 0), HID_REQ_SET_REPORT, USB_DIR_OUT | USB_RECIP_INTERFACE | USB_TYPE_CLASS, - 0x0300, 0, feature_buffer, 5, 500); + 0x0300, 0, feature_buffer, 8, 500); + + if (tries++ >= 3) + break; - if (retval != 5) + if (retval == EPIPE) + usb_clear_halt(port->serial->dev, 0x00); + } while (retval != 8 && retval != ENODEV); + + if (retval != 8) err("%s - failed sending serial line settings - %d", __FUNCTION__, retval); else { spin_lock_irqsave(&priv->lock, flags); - priv->baud_rate = n_baud_rate; + priv->baud_rate = new_baudrate; priv->cbr_mask = baud_mask; - priv->current_config = config; - ++priv->cmd_count; + priv->current_config = feature_buffer[4]; spin_unlock_irqrestore(&priv->lock, flags); } break; case CYPRESS_GET_CONFIG: dbg("%s - retreiving serial line settings", __FUNCTION__); - /* reset values in feature buffer */ - memset(feature_buffer, 0, 5); + /* set initial values in feature buffer */ + memset(feature_buffer, 0, 8); + do { retval = usb_control_msg (port->serial->dev, usb_rcvctrlpipe(port->serial->dev, 0), HID_REQ_GET_REPORT, USB_DIR_IN | USB_RECIP_INTERFACE | USB_TYPE_CLASS, - 0x0300, 0, feature_buffer, 5, 500); + 0x0300, 0, feature_buffer, 8, 500); + + if (tries++ >= 3) + break; + + if (retval == EPIPE) + usb_clear_halt(port->serial->dev, 0x00); + } while (retval != 5 && retval != ENODEV); + if (retval != 5) { err("%s - failed to retreive serial line settings - %d", __FUNCTION__, retval); return retval; } else { spin_lock_irqsave(&priv->lock, flags); + /* store the config in one byte, and later use bit masks to check values */ priv->current_config = feature_buffer[4]; - /* reverse the process above to get the baud_mask value */ - n_baud_rate = 0; // reset bits - for (i = 0; i < 4; ++i) { - n_baud_rate |= ( feature_buffer[i] << (i*8) ); - } + priv->baud_rate = *((u_int32_t *)feature_buffer); - priv->baud_rate = n_baud_rate; - if ( (priv->cbr_mask = rate_to_mask(n_baud_rate)) == 0x40) + if ( (priv->cbr_mask = rate_to_mask(priv->baud_rate)) == 0x40) dbg("%s - failed setting the baud mask (not defined)", __FUNCTION__); - ++priv->cmd_count; spin_unlock_irqrestore(&priv->lock, flags); } - break; - default: - err("%s - unsupported serial control command issued", __FUNCTION__); } + spin_lock_irqsave(&priv->lock, flags); + ++priv->cmd_count; + spin_unlock_irqrestore(&priv->lock, flags); + return retval; } /* cypress_serial_control */ -/* given a baud mask, it will return speed on success */ +/* given a baud mask, it will return integer baud on success */ static int mask_to_rate (unsigned mask) { int rate; @@ -438,11 +445,12 @@ static int generic_startup (struct usb_serial *serial) usb_reset_configuration (serial->dev); + interval = 1; priv->cmd_ctrl = 0; priv->line_control = 0; priv->termios_initialized = 0; - priv->calledfromopen = 0; priv->rx_flags = 0; + priv->cbr_mask = B300; usb_set_serial_port_data(serial->port[0], priv); return (0); @@ -513,7 +521,6 @@ static int cypress_open (struct usb_serial_port *port, struct file *filp) dbg("%s - port %d", __FUNCTION__, port->number); /* clear halts before open */ - usb_clear_halt(serial->dev, 0x00); usb_clear_halt(serial->dev, 0x81); usb_clear_halt(serial->dev, 0x02); @@ -531,7 +538,6 @@ static int cypress_open (struct usb_serial_port *port, struct file *filp) /* raise both lines and set termios */ spin_lock_irqsave(&priv->lock, flags); priv->line_control = CONTROL_DTR | CONTROL_RTS; - priv->calledfromopen = 1; priv->cmd_ctrl = 1; spin_unlock_irqrestore(&priv->lock, flags); result = cypress_write(port, NULL, 0); @@ -553,7 +559,7 @@ static int cypress_open (struct usb_serial_port *port, struct file *filp) usb_fill_int_urb(port->interrupt_in_urb, serial->dev, usb_rcvintpipe(serial->dev, port->interrupt_in_endpointAddress), port->interrupt_in_urb->transfer_buffer, port->interrupt_in_urb->transfer_buffer_length, - cypress_read_int_callback, port, port->interrupt_in_urb->interval); + cypress_read_int_callback, port, interval); result = usb_submit_urb(port->interrupt_in_urb, GFP_KERNEL); if (result){ @@ -680,12 +686,12 @@ static void cypress_send(struct usb_serial_port *port) spin_lock_irqsave(&priv->lock, flags); switch (port->interrupt_out_size) { case 32: - // this is for the CY7C64013... + /* this is for the CY7C64013... */ offset = 2; port->interrupt_out_buffer[0] = priv->line_control; break; case 8: - // this is for the CY7C63743... + /* this is for the CY7C63743... */ offset = 1; port->interrupt_out_buffer[0] = priv->line_control; break; @@ -738,6 +744,7 @@ send: port->interrupt_out_urb->transfer_buffer_length = actual_size; port->interrupt_out_urb->dev = port->serial->dev; + port->interrupt_out_urb->interval = interval; result = usb_submit_urb (port->interrupt_out_urb, GFP_ATOMIC); if (result) { dev_err(&port->dev, "%s - failed submitting write urb, error %d\n", __FUNCTION__, @@ -910,7 +917,7 @@ static void cypress_set_termios (struct usb_serial_port *port, struct termios *o unsigned cflag, iflag, baud_mask; unsigned long flags; __u8 oldlines; - int linechange; + int linechange = 0; dbg("%s - port %d", __FUNCTION__, port->number); @@ -996,15 +1003,7 @@ static void cypress_set_termios (struct usb_serial_port *port, struct termios *o case B115200: dbg("%s - setting baud 115200bps", __FUNCTION__); break; default: dbg("%s - unknown masked baud rate", __FUNCTION__); } - priv->line_control |= CONTROL_DTR; - - /* toggle CRTSCTS? - don't do this if being called from cypress_open */ - if (!priv->calledfromopen) { - if (cflag & CRTSCTS) - priv->line_control |= CONTROL_RTS; - else - priv->line_control &= ~CONTROL_RTS; - } + priv->line_control = (CONTROL_DTR | CONTROL_RTS); } spin_unlock_irqrestore(&priv->lock, flags); @@ -1014,8 +1013,6 @@ static void cypress_set_termios (struct usb_serial_port *port, struct termios *o cypress_serial_control(port, baud_mask, data_bits, stop_bits, parity_enable, parity_type, 0, CYPRESS_SET_CONFIG); - msleep(50); /* give some time between change and read (50ms) */ - /* we perform a CYPRESS_GET_CONFIG so that the current settings are filled into the private structure * this should confirm that all is working if it returns what we just set */ cypress_serial_control(port, 0, 0, 0, 0, 0, 0, CYPRESS_GET_CONFIG); @@ -1031,7 +1028,6 @@ static void cypress_set_termios (struct usb_serial_port *port, struct termios *o dbg("Using custom termios settings for a baud rate of 4800bps."); /* define custom termios settings for NMEA protocol */ - tty->termios->c_iflag /* input modes - */ &= ~(IGNBRK /* disable ignore break */ | BRKINT /* disable break causes interrupt */ @@ -1052,23 +1048,16 @@ static void cypress_set_termios (struct usb_serial_port *port, struct termios *o | ISIG /* disable interrupt, quit, and suspend special characters */ | IEXTEN); /* disable non-POSIX special characters */ - } else if (priv->chiptype == CT_CYPHIDCOM) { - - // Software app handling it for device... + } /* CT_CYPHIDCOM: Application should handle this for device */ - } linechange = (priv->line_control != oldlines); spin_unlock_irqrestore(&priv->lock, flags); /* if necessary, set lines */ - if (!priv->calledfromopen && linechange) { + if (linechange) { priv->cmd_ctrl = 1; cypress_write(port, NULL, 0); } - - if (priv->calledfromopen) - priv->calledfromopen = 0; - } /* cypress_set_termios */ @@ -1164,7 +1153,7 @@ static void cypress_read_int_callback(struct urb *urb, struct pt_regs *regs) spin_lock_irqsave(&priv->lock, flags); switch(urb->actual_length) { case 32: - // This is for the CY7C64013... + /* This is for the CY7C64013... */ priv->current_status = data[0] & 0xF8; bytes = data[1]+2; i=2; @@ -1172,7 +1161,7 @@ static void cypress_read_int_callback(struct urb *urb, struct pt_regs *regs) havedata = 1; break; case 8: - // This is for the CY7C63743... + /* This is for the CY7C63743... */ priv->current_status = data[0] & 0xF8; bytes = (data[0] & 0x07)+1; i=1; @@ -1245,7 +1234,7 @@ continue_read: port->interrupt_in_urb->transfer_buffer, port->interrupt_in_urb->transfer_buffer_length, cypress_read_int_callback, port, - port->interrupt_in_urb->interval); + interval); result = usb_submit_urb(port->interrupt_in_urb, GFP_ATOMIC); if (result) dev_err(&urb->dev->dev, "%s - failed resubmitting read urb, error %d\n", __FUNCTION__, result); @@ -1274,6 +1263,8 @@ static void cypress_write_int_callback(struct urb *urb, struct pt_regs *regs) dbg("%s - urb shutting down with status: %d", __FUNCTION__, urb->status); priv->write_urb_in_use = 0; return; + case -EPIPE: /* no break needed */ + usb_clear_halt(port->serial->dev, 0x02); default: /* error in the urb, so we have to resubmit it */ dbg("%s - Overflow in write", __FUNCTION__); @@ -1535,3 +1526,5 @@ module_param(debug, bool, S_IRUGO | S_IWUSR); MODULE_PARM_DESC(debug, "Debug enabled or not"); module_param(stats, bool, S_IRUGO | S_IWUSR); MODULE_PARM_DESC(stats, "Enable statistics or not"); +module_param(interval, int, S_IRUGO | S_IWUSR); +MODULE_PARM_DESC(interval, "Overrides interrupt interval");