X-Git-Url: https://err.no/cgi-bin/gitweb.cgi?a=blobdiff_plain;f=drivers%2Fspi%2FKconfig;h=fae9e8f3d092ce6e34afcf4e89ed5cfc73f0d39f;hb=e7a05aa9e697ff6fc165d45671cdcca601942f62;hp=a77ede598d341bcc49581e124868eef1aef4810e;hpb=95b00786f3b8fa99f53931361beeb4c10504ad87;p=linux-2.6

diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index a77ede598d..fae9e8f3d0 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -5,11 +5,9 @@
 # nobody's needed a slave side API yet.  The master-role API is not
 # fully appropriate there, so it'd need some thought to do well.
 #
-menu "SPI support"
-	depends on HAS_IOMEM
-
-config SPI
+menuconfig SPI
 	bool "SPI support"
+	depends on HAS_IOMEM
 	help
 	  The "Serial Peripheral Interface" is a low level synchronous
 	  protocol.  Chips that support SPI can have data transfer rates
@@ -28,9 +26,11 @@ config SPI
 	  (half duplex), SSP, SSI, and PSP.  This driver framework should
 	  work with most such devices and controllers.
 
+if SPI
+
 config SPI_DEBUG
 	boolean "Debug support for SPI drivers"
-	depends on SPI && DEBUG_KERNEL
+	depends on DEBUG_KERNEL
 	help
 	  Say "yes" to enable debug messaging (like dev_dbg and pr_debug),
 	  sysfs, and debugfs support in SPI controller and protocol drivers.
@@ -61,7 +61,7 @@ config SPI_ATMEL
 
 config SPI_BFIN
 	tristate "SPI controller driver for ADI Blackfin5xx"
-	depends on SPI_MASTER && BFIN
+	depends on SPI_MASTER && BLACKFIN
 	help
 	  This is the SPI controller master driver for Blackfin 5xx processor.
 
@@ -144,15 +144,16 @@ config SPI_OMAP_UWIRE
 	  This hooks up to the MicroWire controller on OMAP1 chips.
 
 config SPI_OMAP24XX
-	tristate "McSPI driver for OMAP24xx"
-	depends on SPI_MASTER && ARCH_OMAP24XX
+	tristate "McSPI driver for OMAP24xx/OMAP34xx"
+	depends on SPI_MASTER && (ARCH_OMAP24XX || ARCH_OMAP34XX)
 	help
-	  SPI master controller for OMAP24xx Multichannel SPI
+	  SPI master controller for OMAP24xx/OMAP34xx Multichannel SPI
 	  (McSPI) modules.
 
 config SPI_PXA2XX
 	tristate "PXA2xx SSP SPI master"
 	depends on SPI_MASTER && ARCH_PXA && EXPERIMENTAL
+	select PXA_SSP
 	help
 	  This enables using a PXA2xx SSP port as a SPI master controller.
 	  The driver can be configured to use any SSP port and additional
@@ -175,6 +176,13 @@ config SPI_S3C24XX_GPIO
 	  the inbuilt hardware cannot provide the transfer mode, or
 	  where the board is using non hardware connected pins.
 
+config SPI_SH_SCI
+	tristate "SuperH SCI SPI controller"
+	depends on SPI_MASTER && SUPERH
+	select SPI_BITBANG
+	help
+	  SPI driver for SuperH SCI blocks.
+
 config SPI_TXX9
 	tristate "Toshiba TXx9 SPI controller"
 	depends on SPI_MASTER && GENERIC_GPIO && CPU_TX49XX
@@ -237,5 +245,4 @@ config SPI_TLE62X0
 
 # (slave support would go here)
 
-endmenu # "SPI support"
-
+endif # SPI