X-Git-Url: https://err.no/cgi-bin/gitweb.cgi?a=blobdiff_plain;f=drivers%2Fnet%2FKconfig;h=734f8403c806cd0fcf5a22757991d2b26fbebdfb;hb=df570f93337ddb46f1e30dd167c27b5fdcec637b;hp=c5519250efd978235a9a4ba73ed1f80f641978cf;hpb=973ed7c49a5c2271a10ce54ac06bba5617fca3a8;p=linux-2.6

diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index c5519250ef..734f8403c8 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -135,6 +135,12 @@ config TUN
 
 	  If you don't know what to use this for, you don't need it.
 
+config VETH
+	tristate "Virtual ethernet device"
+	---help---
+	  The device is an ethernet tunnel. Devices are created in pairs. When
+	  one end receives the packet it appears on its pair and vice versa.
+
 config NET_SB1000
 	tristate "General Instruments Surfboard 1000"
 	depends on PNP
@@ -480,26 +486,6 @@ config SGI_IOC3_ETH
 	  the Ethernet-HOWTO, available from
 	  <http://www.tldp.org/docs.html#howto>.
 
-config SGI_IOC3_ETH_HW_RX_CSUM
-	bool "Receive hardware checksums"
-	depends on SGI_IOC3_ETH && INET
-	default y
-	help
-	  The SGI IOC3 network adapter supports TCP and UDP checksums in
-	  hardware to offload processing of these checksums from the CPU.  At
-	  the moment only acceleration of IPv4 is supported.  This option
-	  enables offloading for checksums on receive.  If unsure, say Y.
-
-config SGI_IOC3_ETH_HW_TX_CSUM
-	bool "Transmit hardware checksums"
-	depends on SGI_IOC3_ETH && INET
-	default y
-	help
-	  The SGI IOC3 network adapter supports TCP and UDP checksums in
-	  hardware to offload processing of these checksums from the CPU.  At
-	  the moment only acceleration of IPv4 is supported.  This option
-	  enables offloading for checksums on transmit.  If unsure, say Y.
-
 config MIPS_SIM_NET
 	tristate "MIPS simulator Network device"
 	depends on MIPS_SIM
@@ -2501,6 +2487,7 @@ config CHELSIO_T3
 config EHEA
 	tristate "eHEA Ethernet support"
 	depends on IBMEBUS
+	select INET_LRO
 	---help---
 	  This driver supports the IBM pSeries eHEA ethernet adapter.
 
@@ -2576,6 +2563,7 @@ config MYRI10GE
 	depends on PCI
 	select FW_LOADER
 	select CRC32
+	select INET_LRO
 	---help---
 	  This driver supports Myricom Myri-10G Dual Protocol interface in
 	  Ethernet mode. If the eeprom on your board is not recent enough,
@@ -3074,6 +3062,16 @@ config NETCONSOLE
 	If you want to log kernel messages over the network, enable this.
 	See <file:Documentation/networking/netconsole.txt> for details.
 
+config NETCONSOLE_DYNAMIC
+	bool "Dynamic reconfiguration of logging targets (EXPERIMENTAL)"
+	depends on NETCONSOLE && SYSFS && EXPERIMENTAL
+	select CONFIGFS_FS
+	help
+	  This option enables the ability to dynamically reconfigure target
+	  parameters (interface, IP addresses, port numbers, MAC addresses)
+	  at runtime through a userspace interface exported using configfs.
+	  See <file:Documentation/networking/netconsole.txt> for details.
+
 config NETPOLL
 	def_bool NETCONSOLE