X-Git-Url: https://err.no/cgi-bin/gitweb.cgi?a=blobdiff_plain;f=drivers%2Fnet%2FKconfig;h=1958d9e16a3aaaa606541ee56173b5811a286c5c;hb=dad2ad82c5f058367df79de022bd12d36afcd065;hp=c748b0e1641921b195d5df144ae0addba10eb3b3;hpb=312f5726055534be1dc9dd369be13aabd2943fcb;p=linux-2.6

diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index c748b0e164..1958d9e16a 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -475,6 +475,14 @@ config SGI_IOC3_ETH_HW_TX_CSUM
 	  the moment only acceleration of IPv4 is supported.  This option
 	  enables offloading for checksums on transmit.  If unsure, say Y.
 
+config MIPS_SIM_NET
+	tristate "MIPS simulator Network device (EXPERIMENTAL)"
+	depends on NETDEVICES && MIPS_SIM && EXPERIMENTAL
+	help
+	  The MIPSNET device is a simple Ethernet network device which is
+	  emulated by the MIPS Simulator.
+	  If you are not using a MIPSsim or are unsure, say N.
+
 config SGI_O2MACE_ETH
 	tristate "SGI O2 MACE Fast Ethernet support"
 	depends on NET_ETHERNET && SGI_IP32=y
@@ -1155,38 +1163,74 @@ config IBMVETH
 	  be called ibmveth.
 
 config IBM_EMAC
-	bool "IBM PPC4xx EMAC driver support"
+	tristate "PowerPC 4xx on-chip Ethernet support"
 	depends on 4xx
-	select CRC32
-	---help---
-	  This driver supports the IBM PPC4xx EMAC family of on-chip
-	  Ethernet controllers.
-
-config IBM_EMAC_ERRMSG
-	bool "Verbose error messages"
-	depends on IBM_EMAC && BROKEN
+	help
+	  This driver supports the PowerPC 4xx EMAC family of on-chip
+          Ethernet controllers.
 
 config IBM_EMAC_RXB
 	int "Number of receive buffers"
 	depends on IBM_EMAC
-	default "128" if IBM_EMAC4
-	default "64"
+	default "128"
 
 config IBM_EMAC_TXB
 	int "Number of transmit buffers"
 	depends on IBM_EMAC
-	default "128" if IBM_EMAC4
-	default "8"
+	default "64"
 
-config IBM_EMAC_FGAP
-	int "Frame gap"
+config IBM_EMAC_POLL_WEIGHT
+	int "MAL NAPI polling weight"
 	depends on IBM_EMAC
-	default "8"
+	default "32"
 
-config IBM_EMAC_SKBRES
-	int "Skb reserve amount"
+config IBM_EMAC_RX_COPY_THRESHOLD
+	int "RX skb copy threshold (bytes)"
+	depends on IBM_EMAC
+	default "256"
+
+config IBM_EMAC_RX_SKB_HEADROOM
+	int "Additional RX skb headroom (bytes)"
 	depends on IBM_EMAC
 	default "0"
+	help
+	  Additional receive skb headroom. Note, that driver
+	  will always reserve at least 2 bytes to make IP header
+	  aligned, so usualy there is no need to add any additional
+	  headroom.
+	  
+	  If unsure, set to 0.
+
+config IBM_EMAC_PHY_RX_CLK_FIX
+	bool "PHY Rx clock workaround"
+	depends on IBM_EMAC && (405EP || 440GX || 440EP || 440GR)
+	help
+	  Enable this if EMAC attached to a PHY which doesn't generate
+	  RX clock if there is no link, if this is the case, you will 
+	  see "TX disable timeout" or "RX disable timeout" in the system
+	  log.
+	  
+	  If unsure, say N.
+
+config IBM_EMAC_DEBUG
+	bool "Debugging"
+	depends on IBM_EMAC
+	default n
+
+config IBM_EMAC_ZMII
+	bool
+	depends on IBM_EMAC && (NP405H || NP405L || 44x)
+	default y
+
+config IBM_EMAC_RGMII
+	bool
+	depends on IBM_EMAC && 440GX
+	default y
+		
+config IBM_EMAC_TAH
+	bool
+	depends on IBM_EMAC && 440GX
+	default y
 
 config NET_PCI
 	bool "EISA, VLB, PCI and on board controllers"
@@ -1767,6 +1811,7 @@ config NE_H8300
 	  controller on the Renesas H8/300 processor.
 
 source "drivers/net/fec_8xx/Kconfig"
+source "drivers/net/fs_enet/Kconfig"
 
 endmenu
 
@@ -2083,6 +2128,7 @@ config SPIDER_NET
 config GIANFAR
 	tristate "Gianfar Ethernet"
 	depends on 85xx || 83xx
+	select PHYLIB
 	help
 	  This driver supports the Gigabit TSEC on the MPC85xx 
 	  family of chips, and the FEC on the 8540
@@ -2192,8 +2238,8 @@ config S2IO
 	depends on PCI
 	---help---
 	  This driver supports the 10Gbe XFrame NIC of S2IO. 
-	  For help regarding driver compilation, installation and 
-	  tuning please look into ~/drivers/net/s2io/README.txt.
+	  More specific information on configuring the driver is in 
+	  <file:Documentation/networking/s2io.txt>.
 
 config S2IO_NAPI
 	bool "Use Rx Polling (NAPI) (EXPERIMENTAL)"
@@ -2212,17 +2258,6 @@ config S2IO_NAPI
 
 	  If in doubt, say N.
 
-config 2BUFF_MODE
-	bool "Use 2 Buffer Mode on Rx side."
-	depends on S2IO
-	---help---
-	On enabling the 2 buffer mode, the received frame will be
-	split into 2 parts before being DMA'ed to the hosts memory.
-	The parts are the ethernet header and ethernet payload. 
-	This is useful on systems where DMA'ing to to unaligned 
-	physical memory loactions comes with a heavy price.
-	If not sure please say N.
-
 endmenu
 
 if !UML
@@ -2243,6 +2278,20 @@ config ISERIES_VETH
 	tristate "iSeries Virtual Ethernet driver support"
 	depends on PPC_ISERIES
 
+config RIONET
+	tristate "RapidIO Ethernet over messaging driver support"
+	depends on NETDEVICES && RAPIDIO
+
+config RIONET_TX_SIZE
+	int "Number of outbound queue entries"
+	depends on RIONET
+	default "128"
+
+config RIONET_RX_SIZE
+	int "Number of inbound queue entries"
+	depends on RIONET
+	default "128"
+
 config FDDI
 	bool "FDDI driver support"
 	depends on (PCI || EISA)