X-Git-Url: https://err.no/cgi-bin/gitweb.cgi?a=blobdiff_plain;f=drivers%2Fleds%2FKconfig;h=86a369bc57d6d91c9137da6940904d6172cf9f90;hb=42c59208219a2d43f0dde94bebc68c20b95b13ce;hp=cf3a6d4d947567297d5d999684b2faa27a311419;hpb=cec035de8265b18252742ef359b12e9694641112;p=linux-2.6

diff --git a/drivers/leds/Kconfig b/drivers/leds/Kconfig
index cf3a6d4d94..86a369bc57 100644
--- a/drivers/leds/Kconfig
+++ b/drivers/leds/Kconfig
@@ -1,6 +1,5 @@
 menuconfig NEW_LEDS
 	bool "LED Support"
-	depends on HAS_IOMEM
 	help
 	  Say Y to enable Linux LED support.  This allows control of supported
 	  LEDs from both userspace and optionally, by kernel events (triggers).
@@ -18,6 +17,13 @@ config LEDS_CLASS
 
 comment "LED drivers"
 
+config LEDS_ATMEL_PWM
+	tristate "LED Support using Atmel PWM outputs"
+	depends on LEDS_CLASS && ATMEL_PWM
+	help
+	  This option enables support for LEDs driven using outputs
+	  of the dedicated PWM controller found on newer Atmel SOCs.
+
 config LEDS_CORGI
 	tristate "LED Support for the Sharp SL-C7x0 series"
 	depends on LEDS_CLASS && PXA_SHARP_C7xx
@@ -39,22 +45,6 @@ config LEDS_SPITZ
 	  This option enables support for the LEDs on Sharp Zaurus
 	  SL-Cxx00 series (C1000, C3000, C3100).
 
-config LEDS_IXP4XX
-	tristate "LED Support for GPIO connected LEDs on IXP4XX processors"
-	depends on LEDS_CLASS && ARCH_IXP4XX
-	help
-	  This option enables support for the LEDs connected to GPIO
-	  outputs of the Intel IXP4XX processors.  To be useful the
-	  particular board must have LEDs and they must be connected
-	  to the GPIO lines.  If unsure, say Y.
-
-config LEDS_TOSA
-	tristate "LED Support for the Sharp SL-6000 series"
-	depends on LEDS_CLASS && PXA_SHARPSL
-	help
-	  This option enables support for the LEDs on Sharp Zaurus
-	  SL-6000 series.
-
 config LEDS_S3C24XX
 	tristate "LED Support for Samsung S3C24XX GPIO LEDs"
 	depends on LEDS_CLASS && ARCH_S3C2410
@@ -75,6 +65,12 @@ config LEDS_NET48XX
 	  This option enables support for the Soekris net4801 and net4826 error
 	  LED.
 
+config LEDS_FSG
+	tristate "LED Support for the Freecom FSG-3"
+	depends on LEDS_CLASS && MACH_FSG
+	help
+	  This option enables support for the LEDs on the Freecom FSG-3.
+
 config LEDS_WRAP
 	tristate "LED Support for the WRAP series LEDs"
 	depends on LEDS_CLASS && SCx200_GPIO
@@ -100,6 +96,13 @@ config LEDS_COBALT_RAQ
 	help
 	  This option enables support for the Cobalt Raq series LEDs.
 
+config LEDS_HP6XX
+	tristate "LED Support for the HP Jornada 6xx"
+	depends on LEDS_CLASS && SH_HP6XX
+	help
+	  This option enables led support for the handheld
+	  HP Jornada 620/660/680/690.
+
 config LEDS_GPIO
 	tristate "LED Support for GPIO connected LEDs"
 	depends on LEDS_CLASS && GENERIC_GPIO
@@ -122,12 +125,15 @@ config LEDS_CLEVO_MAIL
 	  programs through the leds subsystem. This LED have three
 	  known mode: off, blink at 0.5Hz and blink at 1Hz.
 
-	  As this LED cannot change it's brightness it blinks instead.
-	  The brightness value 0 means off, 1..127 means blink at 0.5Hz
-	  and 128..255 means blink at 1Hz.
+	  The driver supports two kinds of interface: using ledtrig-timer
+	  or through /sys/class/leds/clevo::mail/brightness. As this LED
+	  cannot change it's brightness it blinks instead. The brightness
+	  value 0 means off, 1..127 means blink at 0.5Hz and 128..255 means
+	  blink at 1Hz.
 
 	  This module can drive the mail LED for the following notebooks:
 
+	  	Clevo D400P
 	  	Clevo D410J
 	  	Clevo D410V
 	  	Clevo D400V/D470V (not tested, but might work)
@@ -135,6 +141,9 @@ config LEDS_CLEVO_MAIL
 	  	Clevo M5x0N (not tested, but might work)
 	  	Positivo Mobile (Clevo M5x0V)
 
+	  If your model is not listed here you can try the "nodetect"
+	  module paramter.
+
 	  To compile this driver as a module, choose M here: the
 	  module will be called leds-clevo-mail.
 
@@ -152,7 +161,11 @@ config LEDS_TRIGGER_TIMER
 	depends on LEDS_TRIGGERS
 	help
 	  This allows LEDs to be controlled by a programmable timer
-	  via sysfs. If unsure, say Y.
+	  via sysfs. Some LED hardware can be programmed to start
+	  blinking the LED without any further software interaction.
+	  For more details read Documentation/leds-class.txt.
+
+	  If unsure, say Y.
 
 config LEDS_TRIGGER_IDE_DISK
 	bool "LED IDE Disk Trigger"
@@ -170,4 +183,11 @@ config LEDS_TRIGGER_HEARTBEAT
 	  load average.
 	  If unsure, say Y.
 
+config LEDS_TRIGGER_DEFAULT_ON
+	tristate "LED Default ON Trigger"
+	depends on LEDS_TRIGGERS
+	help
+	  This allows LEDs to be initialised in the ON state.
+	  If unsure, say Y.
+
 endif # NEW_LEDS