X-Git-Url: https://err.no/cgi-bin/gitweb.cgi?a=blobdiff_plain;f=drivers%2Fide%2FKconfig;h=45b22282f1498b071b6386225ca78afedd21433b;hb=b0bc65b9aa7d9eb8af4895ed772ef7fe2c10687c;hp=aa0e0c9f74c5a132c043b1c6efd82e9e19bf1a94;hpb=dd6d1844af33acb4edd0a40b1770d091a22c94be;p=linux-2.6 diff --git a/drivers/ide/Kconfig b/drivers/ide/Kconfig index aa0e0c9f74..45b22282f1 100644 --- a/drivers/ide/Kconfig +++ b/drivers/ide/Kconfig @@ -152,9 +152,22 @@ config BLK_DEV_IDEDISK If unsure, say Y. config IDEDISK_MULTI_MODE - bool "Use multi-mode by default" - help - If you get this error, try to say Y here: + bool "Use multiple sector mode for Programmed Input/Output by default" + help + This setting is irrelevant for most IDE disks, with direct memory + access, to which multiple sector mode does not apply. Multiple sector + mode is a feature of most modern IDE hard drives, permitting the + transfer of multiple sectors per Programmed Input/Output interrupt, + rather than the usual one sector per interrupt. When this feature is + enabled, it can reduce operating system overhead for disk Programmed + Input/Output. On some systems, it also can increase the data + throughput of Programmed Input/Output. Some drives, however, seemed + to run slower with multiple sector mode enabled. Some drives claimed + to support multiple sector mode, but lost data at some settings. + Under rare circumstances, such failures could result in massive + filesystem corruption. + + If you get the following error, try to say Y here: hda: set_multmode: status=0x51 { DriveReady SeekComplete Error } hda: set_multmode: error=0x04 { DriveStatusError } @@ -190,10 +203,6 @@ config BLK_DEV_IDECD CD-ROM drive, you can say N to all other CD-ROM options, but be sure to say Y or M to "ISO 9660 CD-ROM file system support". - Note that older versions of LILO (LInux LOader) cannot properly deal - with IDE/ATAPI CD-ROMs, so install LILO 16 or higher, available from - . - To compile this driver as a module, choose M here: the module will be called ide-cd. @@ -304,7 +313,6 @@ comment "IDE chipset support/bugfixes" config IDE_GENERIC tristate "generic/default IDE chipset support" - default H8300 help If unsure, say N. @@ -380,9 +388,10 @@ config IDEPCI_SHARE_IRQ config IDEPCI_PCIBUS_ORDER def_bool BLK_DEV_IDE=y && BLK_DEV_IDEPCI +# TODO: split it on per host driver config options (or module parameters) config BLK_DEV_OFFBOARD bool "Boot off-board chipsets first support" - depends on BLK_DEV_IDEPCI + depends on BLK_DEV_IDEPCI && (BLK_DEV_AEC62XX || BLK_DEV_GENERIC || BLK_DEV_HPT34X || BLK_DEV_HPT366 || BLK_DEV_PDC202XX_NEW || BLK_DEV_PDC202XX_OLD || BLK_DEV_TC86C001) help Normally, IDE controllers built into the motherboard (on-board controllers) are assigned to ide0 and ide1 while those on add-in PCI @@ -435,24 +444,6 @@ config BLK_DEV_IDEDMA_PCI bool select BLK_DEV_IDEPCI -config BLK_DEV_IDEDMA_FORCED - bool "Force enable legacy 2.0.X HOSTS to use DMA" - depends on BLK_DEV_IDEDMA_PCI - help - This is an old piece of lost code from Linux 2.0 Kernels. - - Generally say N here. - -# TODO: remove it -config IDEDMA_ONLYDISK - bool "Enable DMA only for disks " - depends on BLK_DEV_IDEDMA_PCI - help - This is used if you know your ATAPI Devices are going to fail DMA - Transfers. - - Generally say N here. - config BLK_DEV_AEC62XX tristate "AEC62XX chipset support" select BLK_DEV_IDEDMA_PCI @@ -492,6 +483,7 @@ config WDC_ALI15X3 config BLK_DEV_AMD74XX tristate "AMD and nVidia IDE support" + depends on !ARM select BLK_DEV_IDEDMA_PCI help This driver adds explicit support for AMD-7xx and AMD-8111 chips @@ -891,6 +883,49 @@ config BLK_DEV_IDE_BAST Say Y here if you want to support the onboard IDE channels on the Simtec BAST or the Thorcom VR1000 +config ETRAX_IDE + bool "ETRAX IDE support" + depends on CRIS && BROKEN + select BLK_DEV_IDEDMA + select IDE_GENERIC + help + Enables the ETRAX IDE driver. + + You can't use parallel ports or SCSI ports at the same time. + +config ETRAX_IDE_DELAY + int "Delay for drives to regain consciousness" + depends on ETRAX_IDE && ETRAX_ARCH_V10 + default 15 + help + Number of seconds to wait for IDE drives to spin up after an IDE + reset. + +choice + prompt "IDE reset pin" + depends on ETRAX_IDE && ETRAX_ARCH_V10 + default ETRAX_IDE_PB7_RESET + +config ETRAX_IDE_PB7_RESET + bool "Port_PB_Bit_7" + help + IDE reset on pin 7 on port B + +config ETRAX_IDE_G27_RESET + bool "Port_G_Bit_27" + help + IDE reset on pin 27 on port G + +endchoice + +config IDE_H8300 + bool "H8300 IDE support" + depends on H8300 + select IDE_GENERIC + default y + help + Enables the H8300 IDE driver. + config BLK_DEV_GAYLE bool "Amiga Gayle IDE interface support" depends on AMIGA @@ -971,7 +1006,7 @@ config BLK_DEV_Q40IDE config BLK_DEV_MPC8xx_IDE bool "MPC8xx IDE support" - depends on 8xx && IDE=y && BLK_DEV_IDE=y && !PPC_MERGE + depends on 8xx && (LWMON || IVMS8 || IVML24 || TQM8xxL) && IDE=y && BLK_DEV_IDE=y && !PPC_MERGE select IDE_GENERIC help This option provides support for IDE on Motorola MPC8xx Systems. @@ -1074,21 +1109,8 @@ endif config BLK_DEV_IDEDMA def_bool BLK_DEV_IDEDMA_PCI || BLK_DEV_IDEDMA_PMAC || BLK_DEV_IDEDMA_ICS || BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA -config IDEDMA_IVB - bool "IGNORE word93 Validation BITS" - depends on BLK_DEV_IDEDMA_PCI || BLK_DEV_IDEDMA_PMAC || BLK_DEV_IDEDMA_ICS - ---help--- - There are unclear terms in ATA-4 and ATA-5 standards how certain - hardware (an 80c ribbon) should be detected. Different interpretations - of the standards have been released in hardware. This causes problems: - for example, a host with Ultra Mode 4 (or higher) will not run - in that mode with an 80c ribbon. - - If you are experiencing compatibility or performance problems, you - MAY try to answer Y here. However, it does not necessarily solve - any of your problems, it could even cause more of them. - - It is normally safe to answer Y; however, the default is N. +config IDE_ARCH_OBSOLETE_INIT + def_bool ALPHA || (ARM && !ARCH_L7200) || BLACKFIN || X86 || IA64 || M32R || MIPS || PARISC || PPC || (SUPERH64 && BLK_DEV_IDEPCI) || SPARC endif