X-Git-Url: https://err.no/cgi-bin/gitweb.cgi?a=blobdiff_plain;f=drivers%2Fata%2Fpata_optidma.c;h=4cd7444563134b88e3ec8da38f9c8502556754a4;hb=4f7faa3f2b99f8fb246c8cdeef971e55ceda4e52;hp=7495758a86fef7b4ac86a0d14a476d558215e0bb;hpb=68d1d07b510bb57a504588adc2bd2758adea0965;p=linux-2.6 diff --git a/drivers/ata/pata_optidma.c b/drivers/ata/pata_optidma.c index 7495758a86..4cd7444563 100644 --- a/drivers/ata/pata_optidma.c +++ b/drivers/ata/pata_optidma.c @@ -64,22 +64,7 @@ static int optidma_pre_reset(struct ata_link *link, unsigned long deadline) if (ap->port_no && !pci_test_config_bits(pdev, &optidma_enable_bits)) return -ENOENT; - return ata_std_prereset(link, deadline); -} - -/** - * optidma_probe_reset - probe reset - * @ap: ATA port - * - * Perform the ATA probe and bus reset sequence plus specific handling - * for this hardware. The Opti needs little handling - we have no UDMA66 - * capability that needs cable detection. All we must do is check the port - * is enabled. - */ - -static void optidma_error_handler(struct ata_port *ap) -{ - ata_bmdma_drive_eh(ap, optidma_pre_reset, ata_std_softreset, NULL, ata_std_postreset); + return ata_sff_prereset(link, deadline); } /** @@ -354,73 +339,18 @@ static struct scsi_host_template optidma_sht = { }; static struct ata_port_operations optidma_port_ops = { + .inherits = &ata_bmdma_port_ops, + .cable_detect = ata_cable_40wire, .set_piomode = optidma_set_pio_mode, .set_dmamode = optidma_set_dma_mode, - .mode_filter = ata_pci_default_filter, - - .tf_load = ata_tf_load, - .tf_read = ata_tf_read, - .check_status = ata_check_status, - .exec_command = ata_exec_command, - .dev_select = ata_std_dev_select, - - .freeze = ata_bmdma_freeze, - .thaw = ata_bmdma_thaw, - .post_internal_cmd = ata_bmdma_post_internal_cmd, - .error_handler = optidma_error_handler, .set_mode = optidma_set_mode, - .cable_detect = ata_cable_40wire, - - .bmdma_setup = ata_bmdma_setup, - .bmdma_start = ata_bmdma_start, - .bmdma_stop = ata_bmdma_stop, - .bmdma_status = ata_bmdma_status, - - .qc_prep = ata_qc_prep, - .qc_issue = ata_qc_issue_prot, - - .data_xfer = ata_data_xfer, - - .irq_handler = ata_interrupt, - .irq_clear = ata_bmdma_irq_clear, - .irq_on = ata_irq_on, - - .port_start = ata_sff_port_start, + .prereset = optidma_pre_reset, }; static struct ata_port_operations optiplus_port_ops = { + .inherits = &optidma_port_ops, .set_piomode = optiplus_set_pio_mode, .set_dmamode = optiplus_set_dma_mode, - .mode_filter = ata_pci_default_filter, - - .tf_load = ata_tf_load, - .tf_read = ata_tf_read, - .check_status = ata_check_status, - .exec_command = ata_exec_command, - .dev_select = ata_std_dev_select, - - .freeze = ata_bmdma_freeze, - .thaw = ata_bmdma_thaw, - .post_internal_cmd = ata_bmdma_post_internal_cmd, - .error_handler = optidma_error_handler, - .set_mode = optidma_set_mode, - .cable_detect = ata_cable_40wire, - - .bmdma_setup = ata_bmdma_setup, - .bmdma_start = ata_bmdma_start, - .bmdma_stop = ata_bmdma_stop, - .bmdma_status = ata_bmdma_status, - - .qc_prep = ata_qc_prep, - .qc_issue = ata_qc_issue_prot, - - .data_xfer = ata_data_xfer, - - .irq_handler = ata_interrupt, - .irq_clear = ata_bmdma_irq_clear, - .irq_on = ata_irq_on, - - .port_start = ata_sff_port_start, }; /** @@ -469,14 +399,12 @@ done_nomsg: /* Wrong chip revision */ static int optidma_init_one(struct pci_dev *dev, const struct pci_device_id *id) { static const struct ata_port_info info_82c700 = { - .sht = &optidma_sht, .flags = ATA_FLAG_SLAVE_POSS, .pio_mask = 0x1f, .mwdma_mask = 0x07, .port_ops = &optidma_port_ops }; static const struct ata_port_info info_82c700_udma = { - .sht = &optidma_sht, .flags = ATA_FLAG_SLAVE_POSS, .pio_mask = 0x1f, .mwdma_mask = 0x07, @@ -502,7 +430,7 @@ static int optidma_init_one(struct pci_dev *dev, const struct pci_device_id *id) if (optiplus_with_udma(dev)) ppi[0] = &info_82c700_udma; - return ata_pci_init_one(dev, ppi); + return ata_pci_sff_init_one(dev, ppi, &optidma_sht, NULL); } static const struct pci_device_id optidma[] = {