X-Git-Url: https://err.no/cgi-bin/gitweb.cgi?a=blobdiff_plain;f=arch%2Fpowerpc%2FKconfig.debug;h=db7cc34c24d4d983030adeebb029be70925587e3;hb=ada397e93d6002021f5bf4ba060aa4ecd5dea3e5;hp=c38bc22370571cc2a92e734ffff205508e52c3d9;hpb=70f227d8846a8a9b1f36f71c42e11cc7c6e9408d;p=linux-2.6

diff --git a/arch/powerpc/Kconfig.debug b/arch/powerpc/Kconfig.debug
index c38bc22370..db7cc34c24 100644
--- a/arch/powerpc/Kconfig.debug
+++ b/arch/powerpc/Kconfig.debug
@@ -144,13 +144,20 @@ config BDI_SWITCH
 
 config BOOTX_TEXT
 	bool "Support for early boot text console (BootX or OpenFirmware only)"
-	depends PPC_OF && PPC_MULTIPLATFORM
+	depends on PPC_OF && PPC_MULTIPLATFORM
 	help
 	  Say Y here to see progress messages from the boot firmware in text
 	  mode. Requires either BootX or Open Firmware.
 
 config PPC_EARLY_DEBUG
 	bool "Early debugging (dangerous)"
+	help
+	  Say Y to enable some early debugging facilities that may be available
+	  for your processor/board combination. Those facilities are hacks
+	  intended to debug problems early during boot, this should not be
+	  enabled in a production kernel.
+	  Note that enabling this will also cause the kernel default log level
+	  to be pushed to max automatically very early during boot
 
 choice
 	prompt "Early debugging console"
@@ -216,21 +223,58 @@ config PPC_EARLY_DEBUG_BEAT
 config PPC_EARLY_DEBUG_44x
 	bool "Early serial debugging for IBM/AMCC 44x CPUs"
 	depends on 44x
-	select PPC_UDBG_16550
 	help
 	  Select this to enable early debugging for IBM 44x chips via the
-	  inbuilt serial port.
+	  inbuilt serial port.  If you enable this, ensure you set
+          PPC_EARLY_DEBUG_44x_PHYSLOW below to suit your target board.
+
+config PPC_EARLY_DEBUG_40x
+	bool "Early serial debugging for IBM/AMCC 40x CPUs"
+	depends on 40x
+	help
+	  Select this to enable early debugging for IBM 40x chips via the
+	  inbuilt serial port. This works on chips with a 16550 compatible
+	  UART. Xilinx chips with uartlite cannot use this option.
+
+config PPC_EARLY_DEBUG_CPM
+	bool "Early serial debugging for Freescale CPM-based serial ports"
+	depends on SERIAL_CPM
+	select PIN_TLB if PPC_8xx
+	help
+	  Select this to enable early debugging for Freescale chips
+	  using a CPM-based serial port.  This assumes that the bootwrapper
+	  has run, and set up the CPM in a particular way.
 
 endchoice
 
 config PPC_EARLY_DEBUG_44x_PHYSLOW
 	hex "Low 32 bits of early debug UART physical address"
-	depends PPC_EARLY_DEBUG_44x
+	depends on PPC_EARLY_DEBUG_44x
 	default "0x40000200"
+	help
+	  You probably want 0x40000200 for ebony boards and
+          0x40000300 for taishan
 
 config PPC_EARLY_DEBUG_44x_PHYSHIGH
 	hex "EPRN of early debug UART physical address"
-	depends PPC_EARLY_DEBUG_44x
+	depends on PPC_EARLY_DEBUG_44x
 	default "0x1"
 
+config PPC_EARLY_DEBUG_40x_PHYSADDR
+	hex "Early debug UART physical address"
+	depends on PPC_EARLY_DEBUG_40x
+	default "0xef600300"
+
+config PPC_EARLY_DEBUG_CPM_ADDR
+	hex "CPM UART early debug transmit descriptor address"
+	depends on PPC_EARLY_DEBUG_CPM
+	default "0xfa202008" if PPC_EP88XC
+	default "0xf0000008" if CPM2
+	default "0xff002008" if CPM1
+	help
+	  This specifies the address of the transmit descriptor
+	  used for early debug output.  Because it is needed before
+	  platform probing is done, all platforms selected must
+	  share the same address.
+
 endmenu