X-Git-Url: https://err.no/cgi-bin/gitweb.cgi?a=blobdiff_plain;f=arch%2Farm%2Fmach-at91%2FKconfig;h=5b0422cdde76e7504010d8b4a8971ef3d0ca7455;hb=c1f3ee120bb61045b1c0a3ead620d1d65af47130;hp=05a9f8a1b45ee5320ddcf3c1d6f18aef96f326be;hpb=81f8320f624a785d77443ace83391d0fdee695f6;p=linux-2.6

diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig
index 05a9f8a1b4..5b0422cdde 100644
--- a/arch/arm/mach-at91/Kconfig
+++ b/arch/arm/mach-at91/Kconfig
@@ -22,6 +22,9 @@ config ARCH_AT91SAM9263
 config ARCH_AT91SAM9RL
 	bool "AT91SAM9RL"
 
+config ARCH_AT91CAP9
+	bool "AT91CAP9"
+
 config ARCH_AT91X40
 	bool "AT91x40"
 
@@ -178,6 +181,21 @@ endif
 
 # ----------------------------------------------------------
 
+if ARCH_AT91CAP9
+
+comment "AT91CAP9 Board Type"
+
+config MACH_AT91CAP9ADK
+	bool "Atmel AT91CAP9A-DK Evaluation Kit"
+	depends on ARCH_AT91CAP9
+	help
+	  Select this if you are using Atmel's AT91CAP9A-DK Evaluation Kit.
+	  <http://www.atmel.com/dyn/products/tools_card.asp?tool_id=4138>
+
+endif
+
+# ----------------------------------------------------------
+
 if ARCH_AT91X40
 
 comment "AT91X40 Board Type"
@@ -198,13 +216,13 @@ comment "AT91 Board Options"
 
 config MTD_AT91_DATAFLASH_CARD
 	bool "Enable DataFlash Card support"
-	depends on (ARCH_AT91RM9200DK || MACH_AT91RM9200EK || MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK)
+	depends on (ARCH_AT91RM9200DK || MACH_AT91RM9200EK || MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK || MACH_AT91CAP9ADK)
 	help
 	  Enable support for the DataFlash card.
 
 config MTD_NAND_AT91_BUSWIDTH_16
 	bool "Enable 16-bit data bus interface to NAND flash"
-	depends on (MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK)
+	depends on (MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK || MACH_AT91CAP9ADK)
 	help
 	  On AT91SAM926x boards both types of NAND flash can be present
 	  (8 and 16 bit data bus width).
@@ -219,6 +237,22 @@ config AT91_PROGRAMMABLE_CLOCKS
 	  Select this if you need to program one or more of the PCK0..PCK3
 	  programmable clock outputs.
 
+config AT91_TIMER_HZ
+       int "Kernel HZ (jiffies per second)"
+       range 32 1024
+       depends on ARCH_AT91
+       default "128" if ARCH_AT91RM9200
+       default "100"
+       help
+	  On AT91rm9200 chips where you're using a system clock derived
+	  from the 32768 Hz hardware clock, this tick rate should divide
+	  it exactly: use a power-of-two value, such as 128 or 256, to
+	  reduce timing errors caused by rounding.
+
+	  On AT91sam926x chips, or otherwise when using a higher precision
+	  system clock (of at least several MHz), rounding is less of a
+	  problem so it can be safer to use a decimal values like 100.
+
 endmenu
 
 endif