X-Git-Url: https://err.no/cgi-bin/gitweb.cgi?a=blobdiff_plain;f=Documentation%2Fkernel-parameters.txt;h=15d8216a93450209fe128d0eafd47057fb4c2d5c;hb=13a6ddb08e58a1bd344da7898c4e2f13bdf18c2f;hp=f4839606988beb27b95ac651eb6d12d71bd13279;hpb=85b375a613085b78531ec86369a51c2f3b922f95;p=linux-2.6

diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
index f483960698..15d8216a93 100644
--- a/Documentation/kernel-parameters.txt
+++ b/Documentation/kernel-parameters.txt
@@ -627,8 +627,7 @@ and is between 256 and 4096 characters. It is defined in the file
 	eata=		[HW,SCSI]
 
 	edd=		[EDD]
-			Format: {"of[f]" | "sk[ipmbr]"}
-			See comment in arch/i386/boot/edd.S
+			Format: {"off" | "on" | "skip[mbr]"}
 
 	eisa_irq_edge=	[PARISC,HW]
 			See header of drivers/parisc/eisa.c.
@@ -772,10 +771,6 @@ and is between 256 and 4096 characters. It is defined in the file
 			Format: ide=nodma or ide=doubler
 			See Documentation/ide/ide.txt.
 
-	ide?=		[HW] (E)IDE subsystem
-			Format: ide?=ata66 or chipset specific parameters.
-			See Documentation/ide/ide.txt.
-
 	idebus=		[HW] (E)IDE subsystem - VLB/PCI bus speed
 			See Documentation/ide/ide.txt.
 
@@ -847,6 +842,10 @@ and is between 256 and 4096 characters. It is defined in the file
 			than 32 bit addressing. The default is to look
 			for translation below 32 bit and if not available
 			then look in the higher range.
+		strict [Default Off]
+			With this option on every unmap_single operation will
+			result in a hardware IOTLB flush operation as opposed
+			to batching them for performance.
 
 	io_delay=	[X86-32,X86-64] I/O delay method
 		0x80
@@ -954,6 +953,8 @@ and is between 256 and 4096 characters. It is defined in the file
 
 	l2cr=		[PPC]
 
+	l3cr=		[PPC]
+
 	lapic		[X86-32,APIC] Enable the local APIC even if BIOS
 			disabled it.
 
@@ -1387,6 +1388,13 @@ and is between 256 and 4096 characters. It is defined in the file
 
 	nr_uarts=	[SERIAL] maximum number of UARTs to be registered.
 
+	olpc_ec_timeout= [OLPC] ms delay when issuing EC commands
+			Rather than timing out after 20 ms if an EC
+			command is not properly ACKed, override the length
+			of the timeout.  We have interrupts disabled while
+			waiting for the ACK, so if this is set too high
+			interrupts *may* be lost!
+
 	opl3=		[HW,OSS]
 			Format: <io>
 
@@ -1469,10 +1477,6 @@ and is between 256 and 4096 characters. It is defined in the file
 		nomsi		[MSI] If the PCI_MSI kernel config parameter is
 				enabled, this kernel boot option can be used to
 				disable the use of MSI interrupts system-wide.
-		nosort		[X86-32] Don't sort PCI devices according to
-				order given by the PCI BIOS. This sorting is
-				done to get a device order compatible with
-				older kernels.
 		biosirq		[X86-32] Use PCI BIOS calls to get the interrupt
 				routing table. These calls are known to be buggy
 				on several machines and they hang the machine
@@ -1514,6 +1518,8 @@ and is between 256 and 4096 characters. It is defined in the file
 				This is normally done in pci_enable_device(),
 				so this option is a temporary workaround
 				for broken drivers that don't call it.
+		skip_isa_align	[X86] do not align io start addr, so can
+				handle more pci cards
 		firmware	[ARM] Do not re-enumerate the bus but instead
 				just use the configuration from the
 				bootloader. This is currently used on