X-Git-Url: https://err.no/cgi-bin/gitweb.cgi?a=blobdiff_plain;ds=sidebyside;f=drivers%2Fnet%2Figb%2Figb_main.c;h=8f66e15ec8d6299ed3f95272ff7ec24acde43c60;hb=04489eeb02a40bc15029886cef7285ada3ab0de6;hp=81bba6983ddea9f7d2779044bb9e41b2401edf1b;hpb=49997d75152b3d23c53b0fa730599f2f74c92c65;p=linux-2.6

diff --git a/drivers/net/igb/igb_main.c b/drivers/net/igb/igb_main.c
index 81bba6983d..8f66e15ec8 100644
--- a/drivers/net/igb/igb_main.c
+++ b/drivers/net/igb/igb_main.c
@@ -311,7 +311,7 @@ static void igb_assign_vector(struct igb_adapter *adapter, int rx_queue,
 		array_wr32(E1000_MSIXBM(0), msix_vector, msixbm);
 		break;
 	case e1000_82576:
-		/* Kawela uses a table-based method for assigning vectors.
+		/* The 82576 uses a table-based method for assigning vectors.
 		   Each queue has a single entry in the table to which we write
 		   a vector number along with a "valid" bit.  Sadly, the layout
 		   of the table is somewhat counterintuitive. */
@@ -385,7 +385,7 @@ static void igb_configure_msix(struct igb_adapter *adapter)
 
 	for (i = 0; i < adapter->num_rx_queues; i++) {
 		struct igb_ring *rx_ring = &adapter->rx_ring[i];
-		rx_ring->buddy = 0;
+		rx_ring->buddy = NULL;
 		igb_assign_vector(adapter, i, IGB_N0_QUEUE, vector++);
 		adapter->eims_enable_mask |= rx_ring->eims_value;
 		if (rx_ring->itr_val)
@@ -720,28 +720,6 @@ static void igb_get_hw_control(struct igb_adapter *adapter)
 			ctrl_ext | E1000_CTRL_EXT_DRV_LOAD);
 }
 
-static void igb_init_manageability(struct igb_adapter *adapter)
-{
-	struct e1000_hw *hw = &adapter->hw;
-
-	if (adapter->en_mng_pt) {
-		u32 manc2h = rd32(E1000_MANC2H);
-		u32 manc = rd32(E1000_MANC);
-
-		/* enable receiving management packets to the host */
-		/* this will probably generate destination unreachable messages
-		 * from the host OS, but the packets will be handled on SMBUS */
-		manc |= E1000_MANC_EN_MNG2HOST;
-#define E1000_MNG2HOST_PORT_623 (1 << 5)
-#define E1000_MNG2HOST_PORT_664 (1 << 6)
-		manc2h |= E1000_MNG2HOST_PORT_623;
-		manc2h |= E1000_MNG2HOST_PORT_664;
-		wr32(E1000_MANC2H, manc2h);
-
-		wr32(E1000_MANC, manc);
-	}
-}
-
 /**
  * igb_configure - configure the hardware for RX and TX
  * @adapter: private board structure
@@ -755,7 +733,6 @@ static void igb_configure(struct igb_adapter *adapter)
 	igb_set_multi(netdev);
 
 	igb_restore_vlan(adapter);
-	igb_init_manageability(adapter);
 
 	igb_configure_tx(adapter);
 	igb_setup_rctl(adapter);
@@ -1372,7 +1349,8 @@ static void __devexit igb_remove(struct pci_dev *pdev)
 
 	unregister_netdev(netdev);
 
-	if (!igb_check_reset_block(&adapter->hw))
+	if (adapter->hw.phy.ops.reset_phy &&
+	    !igb_check_reset_block(&adapter->hw))
 		adapter->hw.phy.ops.reset_phy(&adapter->hw);
 
 	igb_remove_device(&adapter->hw);
@@ -1493,6 +1471,8 @@ static int igb_open(struct net_device *netdev)
 
 	igb_irq_enable(adapter);
 
+	netif_tx_start_all_queues(netdev);
+
 	/* Fire a link status change interrupt to start the watchdog. */
 	wr32(E1000_ICS, E1000_ICS_LSC);
 
@@ -4521,8 +4501,6 @@ static void igb_io_resume(struct pci_dev *pdev)
 	struct net_device *netdev = pci_get_drvdata(pdev);
 	struct igb_adapter *adapter = netdev_priv(netdev);
 
-	igb_init_manageability(adapter);
-
 	if (netif_running(netdev)) {
 		if (igb_up(adapter)) {
 			dev_err(&pdev->dev, "igb_up failed after reset\n");