X-Git-Url: https://err.no/cgi-bin/gitweb.cgi?a=blobdiff_plain;ds=sidebyside;f=drivers%2Fide%2FKconfig;h=e445fe6e4ba9d7df6f39ff141f6b699c1481cf63;hb=b48d08177fe635a549aaf63eef508be1de069ebf;hp=aa0e0c9f74c5a132c043b1c6efd82e9e19bf1a94;hpb=547307420931344a868275bd7ea7a30f117a15a9;p=linux-2.6

diff --git a/drivers/ide/Kconfig b/drivers/ide/Kconfig
index aa0e0c9f74..e445fe6e4b 100644
--- a/drivers/ide/Kconfig
+++ b/drivers/ide/Kconfig
@@ -152,9 +152,22 @@ config BLK_DEV_IDEDISK
 	  If unsure, say Y.
 
 config IDEDISK_MULTI_MODE
-	bool "Use multi-mode by default"
-	help
-	  If you get this error, try to say Y here:
+	bool "Use multiple sector mode for Programmed Input/Output by default"
+	help
+	  This setting is irrelevant for most IDE disks, with direct memory
+	  access, to which multiple sector mode does not apply. Multiple sector
+	  mode is a feature of most modern IDE hard drives, permitting the
+	  transfer of multiple sectors per Programmed Input/Output interrupt,
+	  rather than the usual one sector per interrupt. When this feature is
+	  enabled, it can reduce operating system overhead for disk Programmed
+	  Input/Output. On some systems, it also can increase the data
+	  throughput of Programmed Input/Output. Some drives, however, seemed
+	  to run slower with multiple sector mode enabled. Some drives claimed
+	  to support multiple sector mode, but lost data at some settings.
+	  Under rare circumstances, such failures could result in massive
+	  filesystem corruption.
+
+	  If you get the following error, try to say Y here:
 
 	  hda: set_multmode: status=0x51 { DriveReady SeekComplete Error }
 	  hda: set_multmode: error=0x04 { DriveStatusError }
@@ -190,10 +203,6 @@ config BLK_DEV_IDECD
 	  CD-ROM drive, you can say N to all other CD-ROM options, but be sure
 	  to say Y or M to "ISO 9660 CD-ROM file system support".
 
-	  Note that older versions of LILO (LInux LOader) cannot properly deal
-	  with IDE/ATAPI CD-ROMs, so install LILO 16 or higher, available from
-	  <http://lilo.go.dyndns.org/>.
-
 	  To compile this driver as a module, choose M here: the
 	  module will be called ide-cd.
 
@@ -380,9 +389,10 @@ config IDEPCI_SHARE_IRQ
 config IDEPCI_PCIBUS_ORDER
 	def_bool BLK_DEV_IDE=y && BLK_DEV_IDEPCI
 
+# TODO: split it on per host driver config options (or module parameters)
 config BLK_DEV_OFFBOARD
 	bool "Boot off-board chipsets first support"
-	depends on BLK_DEV_IDEPCI
+	depends on BLK_DEV_IDEPCI && (BLK_DEV_AEC62XX || BLK_DEV_GENERIC || BLK_DEV_HPT34X || BLK_DEV_HPT366 || BLK_DEV_PDC202XX_NEW || BLK_DEV_PDC202XX_OLD || BLK_DEV_TC86C001)
 	help
 	  Normally, IDE controllers built into the motherboard (on-board
 	  controllers) are assigned to ide0 and ide1 while those on add-in PCI
@@ -435,24 +445,6 @@ config BLK_DEV_IDEDMA_PCI
 	bool
 	select BLK_DEV_IDEPCI
 
-config BLK_DEV_IDEDMA_FORCED
-	bool "Force enable legacy 2.0.X HOSTS to use DMA"
-	depends on BLK_DEV_IDEDMA_PCI
-	help
-	  This is an old piece of lost code from Linux 2.0 Kernels.
-
-	  Generally say N here.
-
-# TODO: remove it
-config IDEDMA_ONLYDISK
-	bool "Enable DMA only for disks "
-	depends on BLK_DEV_IDEDMA_PCI
-	help
-	  This is used if you know your ATAPI Devices are going to fail DMA
-	  Transfers.
-
-	  Generally say N here.
-
 config BLK_DEV_AEC62XX
 	tristate "AEC62XX chipset support"
 	select BLK_DEV_IDEDMA_PCI
@@ -1074,21 +1066,8 @@ endif
 config BLK_DEV_IDEDMA
 	def_bool BLK_DEV_IDEDMA_PCI || BLK_DEV_IDEDMA_PMAC || BLK_DEV_IDEDMA_ICS || BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
 
-config IDEDMA_IVB
-	bool "IGNORE word93 Validation BITS"
-	depends on BLK_DEV_IDEDMA_PCI || BLK_DEV_IDEDMA_PMAC || BLK_DEV_IDEDMA_ICS
-	---help---
-	  There are unclear terms in ATA-4 and ATA-5 standards how certain
-	  hardware (an 80c ribbon) should be detected. Different interpretations
-	  of the standards have been released in hardware. This causes problems:
-	  for example, a host with Ultra Mode 4 (or higher) will not run
-	  in that mode with an 80c ribbon.
-
-	  If you are experiencing compatibility or performance problems, you
-	  MAY try to answer Y here. However, it does not necessarily solve
-	  any of your problems, it could even cause more of them.
-
-	  It is normally safe to answer Y; however, the default is N.
+config IDE_ARCH_OBSOLETE_INIT
+	def_bool ALPHA || (ARM && !ARCH_L7200) || BLACKFIN || X86 || IA64 || M32R || MIPS || PARISC || PPC || (SUPERH64 && BLK_DEV_IDEPCI) || SPARC
 
 endif