#include <linux/skbuff.h>
#include <linux/debugfs.h>
#include <net/mac80211.h>
-#include "ieee80211_rate.h"
-#ifdef CONFIG_MAC80211_MESH
+#include "rate.h"
#include "mesh.h"
-#endif
-
#include "rc80211_pid.h"
int cur_sorted, new_sorted, probe, tmp, n_bitrates, band;
int cur = sta->txrate_idx;
- sdata = IEEE80211_DEV_TO_SUB_IF(sta->dev);
+ sdata = sta->sdata;
sband = local->hw.wiphy->bands[local->hw.conf.channel->band];
band = sband->band;
n_bitrates = sband->n_bitrates;
struct sta_info *sta)
{
#ifdef CONFIG_MAC80211_MESH
- struct ieee80211_sub_if_data *sdata = IEEE80211_DEV_TO_SUB_IF(sta->dev);
+ struct ieee80211_sub_if_data *sdata = sta->sdata;
#endif
struct rc_pid_sta_info *spinfo = sta->rate_ctrl_priv;
struct rc_pid_rateinfo *rinfo = pinfo->rinfo;
}
static void rate_control_pid_tx_status(void *priv, struct net_device *dev,
- struct sk_buff *skb,
- struct ieee80211_tx_status *status)
+ struct sk_buff *skb)
{
struct ieee80211_local *local = wdev_priv(dev->ieee80211_ptr);
struct ieee80211_hdr *hdr = (struct ieee80211_hdr *) skb->data;
struct rc_pid_sta_info *spinfo;
unsigned long period;
struct ieee80211_supported_band *sband;
+ struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
+
+ rcu_read_lock();
sta = sta_info_get(local, hdr->addr1);
sband = local->hw.wiphy->bands[local->hw.conf.channel->band];
if (!sta)
- return;
+ goto unlock;
/* Don't update the state if we're not controlling the rate. */
- sdata = IEEE80211_DEV_TO_SUB_IF(sta->dev);
+ sdata = sta->sdata;
if (sdata->bss && sdata->bss->force_unicast_rateidx > -1) {
sta->txrate_idx = sdata->bss->max_ratectrl_rateidx;
- return;
+ goto unlock;
}
/* Ignore all frames that were sent with a different rate than the rate
* we currently advise mac80211 to use. */
- if (status->control.tx_rate != &sband->bitrates[sta->txrate_idx])
- goto ignore;
+ if (info->tx_rate_idx != sta->txrate_idx)
+ goto unlock;
spinfo = sta->rate_ctrl_priv;
spinfo->tx_num_xmit++;
#ifdef CONFIG_MAC80211_DEBUGFS
- rate_control_pid_event_tx_status(&spinfo->events, status);
+ rate_control_pid_event_tx_status(&spinfo->events, info);
#endif
/* We count frames that totally failed to be transmitted as two bad
* frames, those that made it out but had some retries as one good and
* one bad frame. */
- if (status->excessive_retries) {
+ if (info->status.excessive_retries) {
spinfo->tx_num_failed += 2;
spinfo->tx_num_xmit++;
- } else if (status->retry_count) {
+ } else if (info->status.retry_count) {
spinfo->tx_num_failed++;
spinfo->tx_num_xmit++;
}
- if (status->excessive_retries) {
+ if (info->status.excessive_retries) {
sta->tx_retry_failed++;
sta->tx_num_consecutive_failures++;
sta->tx_num_mpdu_fail++;
sta->tx_num_consecutive_failures = 0;
sta->tx_num_mpdu_ok++;
}
- sta->tx_retry_count += status->retry_count;
- sta->tx_num_mpdu_fail += status->retry_count;
+ sta->tx_retry_count += info->status.retry_count;
+ sta->tx_num_mpdu_fail += info->status.retry_count;
/* Update PID controller state. */
period = (HZ * pinfo->sampling_period + 500) / 1000;
if (time_after(jiffies, spinfo->last_sample + period))
rate_control_pid_sample(pinfo, local, sta);
-ignore:
- sta_info_put(sta);
+ unlock:
+ rcu_read_unlock();
}
static void rate_control_pid_get_rate(void *priv, struct net_device *dev,
int rateidx;
u16 fc;
+ rcu_read_lock();
+
sta = sta_info_get(local, hdr->addr1);
/* Send management frames and broadcast/multicast data using lowest
fc = le16_to_cpu(hdr->frame_control);
if ((fc & IEEE80211_FCTL_FTYPE) != IEEE80211_FTYPE_DATA ||
is_multicast_ether_addr(hdr->addr1) || !sta) {
- sel->rate = rate_lowest(local, sband, sta);
- if (sta)
- sta_info_put(sta);
+ sel->rate_idx = rate_lowest_index(local, sband, sta);
+ rcu_read_unlock();
return;
}
sta->last_txrate_idx = rateidx;
- sta_info_put(sta);
+ rcu_read_unlock();
- sel->rate = &sband->bitrates[rateidx];
+ sel->rate_idx = rateidx;
#ifdef CONFIG_MAC80211_DEBUGFS
rate_control_pid_event_tx_rate(