NUM_IEEE80211_MODES
};
+/**
+ * struct ieee80211_ht_info - describing STA's HT capabilities
+ *
+ * This structure describes most essential parameters needed
+ * to describe 802.11n HT capabilities for an STA.
+ *
+ * @ht_supported: is HT supported by STA, 0: no, 1: yes
+ * @cap: HT capabilities map as described in 802.11n spec
+ * @ampdu_factor: Maximum A-MPDU length factor
+ * @ampdu_density: Minimum A-MPDU spacing
+ * @supp_mcs_set: Supported MCS set as described in 802.11n spec
+ */
+struct ieee80211_ht_info {
+ u8 ht_supported;
+ u16 cap; /* use IEEE80211_HT_CAP_ */
+ u8 ampdu_factor;
+ u8 ampdu_density;
+ u8 supp_mcs_set[16];
+};
+
+/**
+ * struct ieee80211_ht_bss_info - describing BSS's HT characteristics
+ *
+ * This structure describes most essential parameters needed
+ * to describe 802.11n HT characteristics in a BSS
+ *
+ * @primary_channel: channel number of primery channel
+ * @bss_cap: 802.11n's general BSS capabilities (e.g. channel width)
+ * @bss_op_mode: 802.11n's BSS operation modes (e.g. HT protection)
+ */
+struct ieee80211_ht_bss_info {
+ u8 primary_channel;
+ u8 bss_cap; /* use IEEE80211_HT_IE_CHA_ */
+ u8 bss_op_mode; /* use IEEE80211_HT_IE_ */
+};
+
/**
* struct ieee80211_hw_mode - PHY mode definition
*
* This structure describes the capabilities supported by the device
* in a single PHY mode.
*
+ * @list: internal
+ * @channels: pointer to array of supported channels
+ * @rates: pointer to array of supported bitrates
* @mode: the PHY mode for this definition
* @num_channels: number of supported channels
- * @channels: pointer to array of supported channels
* @num_rates: number of supported bitrates
- * @rates: pointer to array of supported bitrates
- * @list: internal
+ * @ht_info: PHY's 802.11n HT abilities for this mode
*/
struct ieee80211_hw_mode {
struct list_head list;
enum ieee80211_phymode mode;
int num_channels;
int num_rates;
+ struct ieee80211_ht_info ht_info;
};
/**
*
* @IEEE80211_CONF_SHORT_SLOT_TIME: use 802.11g short slot time
* @IEEE80211_CONF_RADIOTAP: add radiotap header at receive time (if supported)
- *
+ * @IEEE80211_CONF_SUPPORT_HT_MODE: use 802.11n HT capabilities (if supported)
*/
enum ieee80211_conf_flags {
- IEEE80211_CONF_SHORT_SLOT_TIME = 1<<0,
- IEEE80211_CONF_RADIOTAP = 1<<1,
+ IEEE80211_CONF_SHORT_SLOT_TIME = (1<<0),
+ IEEE80211_CONF_RADIOTAP = (1<<1),
+ IEEE80211_CONF_SUPPORT_HT_MODE = (1<<2),
};
/**
* @antenna_sel_tx: transmit antenna selection, 0: default/diversity,
* 1/2: antenna 0/1
* @antenna_sel_rx: receive antenna selection, like @antenna_sel_tx
+ * @ht_conf: describes current self configuration of 802.11n HT capabilies
+ * @ht_bss_conf: describes current BSS configuration of 802.11n HT parameters
*/
struct ieee80211_conf {
int channel; /* IEEE 802.11 channel number */
u8 antenna_max;
u8 antenna_sel_tx;
u8 antenna_sel_rx;
+
+ struct ieee80211_ht_info ht_conf;
+ struct ieee80211_ht_bss_info ht_bss_conf;
};
/**
*
* @queues: number of available hardware transmit queues for
* data packets. WMM/QoS requires at least four.
+ *
+ * @rate_control_algorithm: rate control algorithm for this hardware.
+ * If unset (NULL), the default algorithm will be used. Must be
+ * set before calling ieee80211_register_hw().
*/
struct ieee80211_hw {
struct ieee80211_conf conf;
struct wiphy *wiphy;
struct workqueue_struct *workqueue;
+ const char *rate_control_algorithm;
void *priv;
u32 flags;
unsigned int extra_tx_headroom;
* and remove_interface calls, i.e. while the interface with the
* given local_address is enabled.
*
- * @set_ieee8021x: Enable/disable IEEE 802.1X. This item requests wlan card
- * to pass unencrypted EAPOL-Key frames even when encryption is
- * configured. If the wlan card does not require such a configuration,
- * this function pointer can be set to NULL.
- *
- * @set_port_auth: Set port authorization state (IEEE 802.1X PAE) to be
- * authorized (@authorized=1) or unauthorized (=0). This function can be
- * used if the wlan hardware or low-level driver implements PAE.
- * mac80211 will filter frames based on authorization state in any case,
- * so this function pointer can be NULL if low-level driver does not
- * require event notification about port state changes.
- *
* @hw_scan: Ask the hardware to service the scan request, no need to start
* the scan state machine in stack.
*
* @get_stats: return low-level statistics
*
- * @set_privacy_invoked: For devices that generate their own beacons and probe
- * response or association responses this updates the state of privacy_invoked
- * returns 0 for success or an error number.
- *
* @get_sequence_counter: For devices that have internal sequence counters this
* callback allows mac80211 to access the current value of a counter.
* This callback seems not well-defined, tell us if you need it.
* @tx_last_beacon: Determine whether the last IBSS beacon was sent by us.
* This is needed only for IBSS mode and the result of this function is
* used to determine whether to reply to Probe Requests.
+ *
+ * @conf_ht: Configures low level driver with 802.11n HT data. Must be atomic.
*/
struct ieee80211_ops {
int (*tx)(struct ieee80211_hw *hw, struct sk_buff *skb,
int (*set_key)(struct ieee80211_hw *hw, enum set_key_cmd cmd,
const u8 *local_address, const u8 *address,
struct ieee80211_key_conf *key);
- int (*set_ieee8021x)(struct ieee80211_hw *hw, int use_ieee8021x);
- int (*set_port_auth)(struct ieee80211_hw *hw, u8 *addr,
- int authorized);
int (*hw_scan)(struct ieee80211_hw *hw, u8 *ssid, size_t len);
int (*get_stats)(struct ieee80211_hw *hw,
struct ieee80211_low_level_stats *stats);
- int (*set_privacy_invoked)(struct ieee80211_hw *hw,
- int privacy_invoked);
int (*get_sequence_counter)(struct ieee80211_hw *hw,
u8* addr, u8 keyidx, u8 txrx,
u32* iv32, u16* iv16);
struct sk_buff *skb,
struct ieee80211_tx_control *control);
int (*tx_last_beacon)(struct ieee80211_hw *hw);
+ int (*conf_ht)(struct ieee80211_hw *hw, struct ieee80211_conf *conf);
};
/**
*/
void ieee80211_scan_completed(struct ieee80211_hw *hw);
+/**
+ * ieee80211_iterate_active_interfaces - iterate active interfaces
+ *
+ * This function iterates over the interfaces associated with a given
+ * hardware that are currently active and calls the callback for them.
+ *
+ * @hw: the hardware struct of which the interfaces should be iterated over
+ * @iterator: the iterator function to call, cannot sleep
+ * @data: first argument of the iterator function
+ */
+void ieee80211_iterate_active_interfaces(struct ieee80211_hw *hw,
+ void (*iterator)(void *data, u8 *mac,
+ int if_id),
+ void *data);
+
#endif /* MAC80211_H */
projects / linux-2.6 / blobdiff