*/
#ifndef _ASM_POWERPC_PPC_PCI_H
#define _ASM_POWERPC_PPC_PCI_H
+#ifdef __KERNEL__
#include <linux/pci.h>
#include <asm/pci-bridge.h>
extern unsigned long isa_io_base;
-extern void pci_setup_pci_controller(struct pci_controller *hose);
extern void pci_setup_phb_io(struct pci_controller *hose, int primary);
extern void pci_setup_phb_io_dynamic(struct pci_controller *hose, int primary);
extern struct pci_dev *ppc64_isabridge_dev; /* may be NULL if no ISA bus */
+/** Bus Unit ID macros; get low and hi 32-bits of the 64-bit BUID */
+#define BUID_HI(buid) ((buid) >> 32)
+#define BUID_LO(buid) ((buid) & 0xffffffff)
+
/* PCI device_node operations */
struct device_node;
typedef void *(*traverse_func)(struct device_node *me, void *data);
void pci_devs_phb_init_dynamic(struct pci_controller *phb);
void __devinit scan_phb(struct pci_controller *hose);
-/* PCI address cache management routines */
-void pci_addr_cache_insert_device(struct pci_dev *dev);
-void pci_addr_cache_remove_device(struct pci_dev *dev);
-
/* From rtas_pci.h */
void init_pci_config_tokens (void);
unsigned long get_phb_buid (struct device_node *);
extern void pSeries_irq_bus_setup(struct pci_bus *bus);
extern unsigned long pci_probe_only;
-extern unsigned long pci_assign_all_buses;
-extern int pci_read_irq_line(struct pci_dev *pci_dev);
+/* ---- EEH internal-use-only related routines ---- */
+#ifdef CONFIG_EEH
+
+void pci_addr_cache_insert_device(struct pci_dev *dev);
+void pci_addr_cache_remove_device(struct pci_dev *dev);
+void pci_addr_cache_build(void);
+struct pci_dev *pci_get_device_by_addr(unsigned long addr);
+
+/**
+ * eeh_slot_error_detail -- record and EEH error condition to the log
+ * @severity: 1 if temporary, 2 if permanent failure.
+ *
+ * Obtains the the EEH error details from the RTAS subsystem,
+ * and then logs these details with the RTAS error log system.
+ */
+void eeh_slot_error_detail (struct pci_dn *pdn, int severity);
+
+/**
+ * rtas_set_slot_reset -- unfreeze a frozen slot
+ *
+ * Clear the EEH-frozen condition on a slot. This routine
+ * does this by asserting the PCI #RST line for 1/8th of
+ * a second; this routine will sleep while the adapter is
+ * being reset.
+ *
+ * Returns a non-zero value if the reset failed.
+ */
+int rtas_set_slot_reset (struct pci_dn *);
+
+/**
+ * eeh_restore_bars - Restore device configuration info.
+ *
+ * A reset of a PCI device will clear out its config space.
+ * This routines will restore the config space for this
+ * device, and is children, to values previously obtained
+ * from the firmware.
+ */
+void eeh_restore_bars(struct pci_dn *);
+
+/**
+ * rtas_configure_bridge -- firmware initialization of pci bridge
+ *
+ * Ask the firmware to configure all PCI bridges devices
+ * located behind the indicated node. Required after a
+ * pci device reset. Does essentially the same hing as
+ * eeh_restore_bars, but for brdges, and lets firmware
+ * do the work.
+ */
+void rtas_configure_bridge(struct pci_dn *);
+
+int rtas_write_config(struct pci_dn *, int where, int size, u32 val);
+int rtas_read_config(struct pci_dn *, int where, int size, u32 *val);
+
+/**
+ * mark and clear slots: find "partition endpoint" PE and set or
+ * clear the flags for each subnode of the PE.
+ */
+void eeh_mark_slot (struct device_node *dn, int mode_flag);
+void eeh_clear_slot (struct device_node *dn, int mode_flag);
+
+/* Find the associated "Partiationable Endpoint" PE */
+struct device_node * find_device_pe(struct device_node *dn);
+
+#endif
+
+#endif /* __KERNEL__ */
#endif /* _ASM_POWERPC_PPC_PCI_H */