#define MPIC_GREG_GLOBAL_CONF_0 0x00020
#define MPIC_GREG_GCONF_RESET 0x80000000
#define MPIC_GREG_GCONF_8259_PTHROU_DIS 0x20000000
+#define MPIC_GREG_GCONF_NO_BIAS 0x10000000
#define MPIC_GREG_GCONF_BASE_MASK 0x000fffff
+#define MPIC_GREG_GCONF_MCK 0x08000000
#define MPIC_GREG_GLOBAL_CONF_1 0x00030
#define MPIC_GREG_GLOBAL_CONF_1_SIE 0x08000000
#define MPIC_GREG_GLOBAL_CONF_1_CLK_RATIO_MASK 0x70000000
#define MPIC_CPU_WHOAMI_MASK 0x0000001f
#define MPIC_CPU_INTACK 0x000a0
#define MPIC_CPU_EOI 0x000b0
+#define MPIC_CPU_MCACK 0x000c0
/*
* Per-source registers
#define TSI108_CPU_WHOAMI 0xffffffff
#define TSI108_CPU_INTACK 0x00004
#define TSI108_CPU_EOI 0x00008
+#define TSI108_CPU_MCACK 0x00004 /* Doesn't really exist here */
/*
* Per-source registers
MPIC_IDX_CPU_WHOAMI,
MPIC_IDX_CPU_INTACK,
MPIC_IDX_CPU_EOI,
+ MPIC_IDX_CPU_MCACK,
MPIC_IDX_IRQ_BASE,
MPIC_IDX_IRQ_STRIDE,
u32 __iomem *base;
#ifdef CONFIG_PPC_DCR
dcr_host_t dhost;
- unsigned int dbase;
- unsigned int doff;
#endif /* CONFIG_PPC_DCR */
};
/* The instance data of a given MPIC */
struct mpic
{
- /* The device node of the interrupt controller */
- struct device_node *of_node;
-
/* The remapper for this MPIC */
struct irq_host *irqhost;
struct mpic_reg_bank cpuregs[MPIC_MAX_CPUS];
struct mpic_reg_bank isus[MPIC_MAX_ISU];
-#ifdef CONFIG_PPC_DCR
- unsigned int dcr_base;
-#endif
-
/* Protected sources */
unsigned long *protected;
unsigned long *hwirq_bitmap;
#endif
+#ifdef CONFIG_MPIC_BROKEN_REGREAD
+ u32 isu_reg0_shadow[MPIC_MAX_IRQ_SOURCES];
+#endif
+
/* link */
struct mpic *next;
#define MPIC_USES_DCR 0x00000080
/* MPIC has 11-bit vector fields (or larger) */
#define MPIC_LARGE_VECTORS 0x00000100
+/* Enable delivery of prio 15 interrupts as MCK instead of EE */
+#define MPIC_ENABLE_MCK 0x00000200
+/* Disable bias among target selection, spread interrupts evenly */
+#define MPIC_NO_BIAS 0x00000400
/* MPIC HW modification ID */
#define MPIC_REGSET_MASK 0xf0000000
*/
-/* Change/Read the priority of an interrupt. Default is 8 for irqs and
+/* Change the priority of an interrupt. Default is 8 for irqs and
* 10 for IPIs. You can call this on both IPIs and IRQ numbers, but the
* IPI number is then the offset'ed (linux irq number mapped to the IPI)
*/
extern void mpic_irq_set_priority(unsigned int irq, unsigned int pri);
-extern unsigned int mpic_irq_get_priority(unsigned int irq);
/* Setup a non-boot CPU */
extern void mpic_setup_this_cpu(void);
/* Send a message (IPI) to a given target (cpu number or MSG_*) */
void smp_mpic_message_pass(int target, int msg);
+/* Unmask a specific virq */
+extern void mpic_unmask_irq(unsigned int irq);
+/* Mask a specific virq */
+extern void mpic_mask_irq(unsigned int irq);
+/* EOI a specific virq */
+extern void mpic_end_irq(unsigned int irq);
+
/* Fetch interrupt from a given mpic */
extern unsigned int mpic_get_one_irq(struct mpic *mpic);
-/* This one gets to the primary mpic */
+/* This one gets from the primary mpic */
extern unsigned int mpic_get_irq(void);
+/* Fetch Machine Check interrupt from primary mpic */
+extern unsigned int mpic_get_mcirq(void);
/* Set the EPIC clock ratio */
void mpic_set_clk_ratio(struct mpic *mpic, u32 clock_ratio);