#define CPM_CR_FCC_PAGE(x) (x + 0x04)
-/* Some opcodes (there are more...later)
+/* CPM2-specific opcodes (see cpm.h for common opcodes)
*/
-#define CPM_CR_INIT_TRX ((ushort)0x0000)
-#define CPM_CR_INIT_RX ((ushort)0x0001)
-#define CPM_CR_INIT_TX ((ushort)0x0002)
-#define CPM_CR_HUNT_MODE ((ushort)0x0003)
-#define CPM_CR_STOP_TX ((ushort)0x0004)
-#define CPM_CR_GRA_STOP_TX ((ushort)0x0005)
-#define CPM_CR_RESTART_TX ((ushort)0x0006)
-#define CPM_CR_SET_GADDR ((ushort)0x0008)
#define CPM_CR_START_IDMA ((ushort)0x0009)
-#define CPM_CR_STOP_IDMA ((ushort)0x000b)
#define mk_cr_cmd(PG, SBC, MCN, OP) \
((PG << 26) | (SBC << 21) | (MCN << 6) | OP)
-#ifndef CONFIG_PPC_CPM_NEW_BINDING
-/* Dual Port RAM addresses. The first 16K is available for almost
- * any CPM use, so we put the BDs there. The first 128 bytes are
- * used for SMC1 and SMC2 parameter RAM, so we start allocating
- * BDs above that. All of this must change when we start
- * downloading RAM microcode.
- */
-#define CPM_DATAONLY_BASE ((uint)128)
-#define CPM_DP_NOSPACE ((uint)0x7fffffff)
-#if defined(CONFIG_8272) || defined(CONFIG_MPC8555)
-#define CPM_DATAONLY_SIZE ((uint)(8 * 1024) - CPM_DATAONLY_BASE)
-#define CPM_FCC_SPECIAL_BASE ((uint)0x00009000)
-#else
-#define CPM_DATAONLY_SIZE ((uint)(16 * 1024) - CPM_DATAONLY_BASE)
-#define CPM_FCC_SPECIAL_BASE ((uint)0x0000b000)
-#endif
-#endif
-
/* The number of pages of host memory we allocate for CPM. This is
* done early in kernel initialization to get physically contiguous
* pages.
*/
extern cpm_cpm2_t __iomem *cpmp; /* Pointer to comm processor */
-#ifdef CONFIG_PPC_CPM_NEW_BINDING
#define cpm_dpalloc cpm_muram_alloc
#define cpm_dpfree cpm_muram_free
#define cpm_dpram_addr cpm_muram_addr
-#else
-extern unsigned long cpm_dpalloc(uint size, uint align);
-extern int cpm_dpfree(unsigned long offset);
-extern unsigned long cpm_dpalloc_fixed(unsigned long offset, uint size, uint align);
-extern void cpm_dpdump(void);
-extern void *cpm_dpram_addr(unsigned long offset);
-#endif
extern void cpm_setbrg(uint brg, uint rate);
extern void cpm2_fastbrg(uint brg, uint rate, int div16);
extern void cpm2_reset(void);
-
-/* Buffer descriptors used by many of the CPM protocols.
-*/
-typedef struct cpm_buf_desc {
- ushort cbd_sc; /* Status and Control */
- ushort cbd_datlen; /* Data length in buffer */
- uint cbd_bufaddr; /* Buffer address in host memory */
-} cbd_t;
-
-#define BD_SC_EMPTY ((ushort)0x8000) /* Receive is empty */
-#define BD_SC_READY ((ushort)0x8000) /* Transmit is ready */
-#define BD_SC_WRAP ((ushort)0x2000) /* Last buffer descriptor */
-#define BD_SC_INTRPT ((ushort)0x1000) /* Interrupt on change */
-#define BD_SC_LAST ((ushort)0x0800) /* Last buffer in frame */
-#define BD_SC_CM ((ushort)0x0200) /* Continous mode */
-#define BD_SC_ID ((ushort)0x0100) /* Rec'd too many idles */
-#define BD_SC_P ((ushort)0x0100) /* xmt preamble */
-#define BD_SC_BR ((ushort)0x0020) /* Break received */
-#define BD_SC_FR ((ushort)0x0010) /* Framing error */
-#define BD_SC_PR ((ushort)0x0008) /* Parity error */
-#define BD_SC_OV ((ushort)0x0002) /* Overrun */
-#define BD_SC_CD ((ushort)0x0001) /* ?? */
-
/* Function code bits, usually generic to devices.
*/
#define CPMFCR_GBL ((u_char)0x20) /* Set memory snooping */
#define SCC_PSMR_NIB22 ((ushort)0x000a) /* Start frame search */
#define SCC_PSMR_FDE ((ushort)0x0001) /* Full duplex enable */
-/* Buffer descriptor control/status used by Ethernet receive.
- * Common to SCC and FCC.
- */
-#define BD_ENET_RX_EMPTY ((ushort)0x8000)
-#define BD_ENET_RX_WRAP ((ushort)0x2000)
-#define BD_ENET_RX_INTR ((ushort)0x1000)
-#define BD_ENET_RX_LAST ((ushort)0x0800)
-#define BD_ENET_RX_FIRST ((ushort)0x0400)
-#define BD_ENET_RX_MISS ((ushort)0x0100)
-#define BD_ENET_RX_BC ((ushort)0x0080) /* FCC Only */
-#define BD_ENET_RX_MC ((ushort)0x0040) /* FCC Only */
-#define BD_ENET_RX_LG ((ushort)0x0020)
-#define BD_ENET_RX_NO ((ushort)0x0010)
-#define BD_ENET_RX_SH ((ushort)0x0008)
-#define BD_ENET_RX_CR ((ushort)0x0004)
-#define BD_ENET_RX_OV ((ushort)0x0002)
-#define BD_ENET_RX_CL ((ushort)0x0001)
-#define BD_ENET_RX_STATS ((ushort)0x01ff) /* All status bits */
-
-/* Buffer descriptor control/status used by Ethernet transmit.
- * Common to SCC and FCC.
- */
-#define BD_ENET_TX_READY ((ushort)0x8000)
-#define BD_ENET_TX_PAD ((ushort)0x4000)
-#define BD_ENET_TX_WRAP ((ushort)0x2000)
-#define BD_ENET_TX_INTR ((ushort)0x1000)
-#define BD_ENET_TX_LAST ((ushort)0x0800)
-#define BD_ENET_TX_TC ((ushort)0x0400)
-#define BD_ENET_TX_DEF ((ushort)0x0200)
-#define BD_ENET_TX_HB ((ushort)0x0100)
-#define BD_ENET_TX_LC ((ushort)0x0080)
-#define BD_ENET_TX_RL ((ushort)0x0040)
-#define BD_ENET_TX_RCMASK ((ushort)0x003c)
-#define BD_ENET_TX_UN ((ushort)0x0002)
-#define BD_ENET_TX_CSL ((ushort)0x0001)
-#define BD_ENET_TX_STATS ((ushort)0x03ff) /* All status bits */
-
/* SCC as UART
*/
typedef struct scc_uart {
uint st_cmask; /* Constant mask for CRC */
} scc_trans_t;
-#define BD_SCC_TX_LAST ((ushort)0x0800)
-
/* How about some FCCs.....
*/
#define FCC_GFMR_DIAG_NORM ((uint)0x00000000)
#define SPI_EB ((u_char)0x10) /* big endian byte order */
-#define BD_IIC_START ((ushort)0x0400)
-
/* IDMA parameter RAM
*/
typedef struct idma {
projects / linux-2.6 / blobdiff