#define _ASM_GENERIC_PGTABLE_H
#ifndef __ASSEMBLY__
+#ifdef CONFIG_MMU
#ifndef __HAVE_ARCH_PTEP_SET_ACCESS_FLAGS
/*
#define pgd_offset_gate(mm, addr) pgd_offset(mm, addr)
#endif
-#ifndef __HAVE_ARCH_LAZY_MMU_PROT_UPDATE
-#define lazy_mmu_prot_update(pte) do { } while (0)
-#endif
-
#ifndef __HAVE_ARCH_MOVE_PTE
#define move_pte(pte, prot, old_addr, new_addr) (pte)
#endif
-/*
- * A facility to provide lazy MMU batching. This allows PTE updates and
- * page invalidations to be delayed until a call to leave lazy MMU mode
- * is issued. Some architectures may benefit from doing this, and it is
- * beneficial for both shadow and direct mode hypervisors, which may batch
- * the PTE updates which happen during this window. Note that using this
- * interface requires that read hazards be removed from the code. A read
- * hazard could result in the direct mode hypervisor case, since the actual
- * write to the page tables may not yet have taken place, so reads though
- * a raw PTE pointer after it has been modified are not guaranteed to be
- * up to date. This mode can only be entered and left under the protection of
- * the page table locks for all page tables which may be modified. In the UP
- * case, this is required so that preemption is disabled, and in the SMP case,
- * it must synchronize the delayed page table writes properly on other CPUs.
- */
-#ifndef __HAVE_ARCH_ENTER_LAZY_MMU_MODE
-#define arch_enter_lazy_mmu_mode() do {} while (0)
-#define arch_leave_lazy_mmu_mode() do {} while (0)
-#define arch_flush_lazy_mmu_mode() do {} while (0)
-#endif
-
-/*
- * A facility to provide batching of the reload of page tables with the
- * actual context switch code for paravirtualized guests. By convention,
- * only one of the lazy modes (CPU, MMU) should be active at any given
- * time, entry should never be nested, and entry and exits should always
- * be paired. This is for sanity of maintaining and reasoning about the
- * kernel code.
- */
-#ifndef __HAVE_ARCH_ENTER_LAZY_CPU_MODE
-#define arch_enter_lazy_cpu_mode() do {} while (0)
-#define arch_leave_lazy_cpu_mode() do {} while (0)
-#define arch_flush_lazy_cpu_mode() do {} while (0)
-#endif
-
/*
* When walking page tables, get the address of the next boundary,
* or the end address of the range if that comes earlier. Although no
}
return 0;
}
+#endif /* CONFIG_MMU */
+
+static inline pte_t __ptep_modify_prot_start(struct mm_struct *mm,
+ unsigned long addr,
+ pte_t *ptep)
+{
+ /*
+ * Get the current pte state, but zero it out to make it
+ * non-present, preventing the hardware from asynchronously
+ * updating it.
+ */
+ return ptep_get_and_clear(mm, addr, ptep);
+}
+
+static inline void __ptep_modify_prot_commit(struct mm_struct *mm,
+ unsigned long addr,
+ pte_t *ptep, pte_t pte)
+{
+ /*
+ * The pte is non-present, so there's no hardware state to
+ * preserve.
+ */
+ set_pte_at(mm, addr, ptep, pte);
+}
+
+#ifndef __HAVE_ARCH_PTEP_MODIFY_PROT_TRANSACTION
+/*
+ * Start a pte protection read-modify-write transaction, which
+ * protects against asynchronous hardware modifications to the pte.
+ * The intention is not to prevent the hardware from making pte
+ * updates, but to prevent any updates it may make from being lost.
+ *
+ * This does not protect against other software modifications of the
+ * pte; the appropriate pte lock must be held over the transation.
+ *
+ * Note that this interface is intended to be batchable, meaning that
+ * ptep_modify_prot_commit may not actually update the pte, but merely
+ * queue the update to be done at some later time. The update must be
+ * actually committed before the pte lock is released, however.
+ */
+static inline pte_t ptep_modify_prot_start(struct mm_struct *mm,
+ unsigned long addr,
+ pte_t *ptep)
+{
+ return __ptep_modify_prot_start(mm, addr, ptep);
+}
+
+/*
+ * Commit an update to a pte, leaving any hardware-controlled bits in
+ * the PTE unmodified.
+ */
+static inline void ptep_modify_prot_commit(struct mm_struct *mm,
+ unsigned long addr,
+ pte_t *ptep, pte_t pte)
+{
+ __ptep_modify_prot_commit(mm, addr, ptep, pte);
+}
+#endif /* __HAVE_ARCH_PTEP_MODIFY_PROT_TRANSACTION */
+
+/*
+ * A facility to provide lazy MMU batching. This allows PTE updates and
+ * page invalidations to be delayed until a call to leave lazy MMU mode
+ * is issued. Some architectures may benefit from doing this, and it is
+ * beneficial for both shadow and direct mode hypervisors, which may batch
+ * the PTE updates which happen during this window. Note that using this
+ * interface requires that read hazards be removed from the code. A read
+ * hazard could result in the direct mode hypervisor case, since the actual
+ * write to the page tables may not yet have taken place, so reads though
+ * a raw PTE pointer after it has been modified are not guaranteed to be
+ * up to date. This mode can only be entered and left under the protection of
+ * the page table locks for all page tables which may be modified. In the UP
+ * case, this is required so that preemption is disabled, and in the SMP case,
+ * it must synchronize the delayed page table writes properly on other CPUs.
+ */
+#ifndef __HAVE_ARCH_ENTER_LAZY_MMU_MODE
+#define arch_enter_lazy_mmu_mode() do {} while (0)
+#define arch_leave_lazy_mmu_mode() do {} while (0)
+#define arch_flush_lazy_mmu_mode() do {} while (0)
+#endif
+
+/*
+ * A facility to provide batching of the reload of page tables with the
+ * actual context switch code for paravirtualized guests. By convention,
+ * only one of the lazy modes (CPU, MMU) should be active at any given
+ * time, entry should never be nested, and entry and exits should always
+ * be paired. This is for sanity of maintaining and reasoning about the
+ * kernel code.
+ */
+#ifndef __HAVE_ARCH_ENTER_LAZY_CPU_MODE
+#define arch_enter_lazy_cpu_mode() do {} while (0)
+#define arch_leave_lazy_cpu_mode() do {} while (0)
+#define arch_flush_lazy_cpu_mode() do {} while (0)
+#endif
+
#endif /* !__ASSEMBLY__ */
#endif /* _ASM_GENERIC_PGTABLE_H */