#ifndef __PXA_REGS_H
#define __PXA_REGS_H
-#include <linux/config.h>
/*
* PXA Chip selects
#define DCSR_STARTINTR (1 << 1) /* Start Interrupt (read / write) */
#define DCSR_BUSERR (1 << 0) /* Bus Error Interrupt (read / write) */
+#define DALGN __REG(0x400000a0) /* DMA Alignment Register */
#define DINT __REG(0x400000f0) /* DMA Interrupt Register */
#define DRCMR(n) __REG2(0x40000100, (n)<<2)
#define STDLL __REG(0x40700000) /* Divisor Latch Low Register (DLAB = 1) (read/write) */
#define STDLH __REG(0x40700004) /* Divisor Latch High Register (DLAB = 1) (read/write) */
+/* Hardware UART (HWUART) */
+#define HWUART HWRBR
+#define HWRBR __REG(0x41600000) /* Receive Buffer Register (read only) */
+#define HWTHR __REG(0x41600000) /* Transmit Holding Register (write only) */
+#define HWIER __REG(0x41600004) /* Interrupt Enable Register (read/write) */
+#define HWIIR __REG(0x41600008) /* Interrupt ID Register (read only) */
+#define HWFCR __REG(0x41600008) /* FIFO Control Register (write only) */
+#define HWLCR __REG(0x4160000C) /* Line Control Register (read/write) */
+#define HWMCR __REG(0x41600010) /* Modem Control Register (read/write) */
+#define HWLSR __REG(0x41600014) /* Line Status Register (read only) */
+#define HWMSR __REG(0x41600018) /* Modem Status Register (read only) */
+#define HWSPR __REG(0x4160001C) /* Scratch Pad Register (read/write) */
+#define HWISR __REG(0x41600020) /* Infrared Selection Register (read/write) */
+#define HWFOR __REG(0x41600024) /* Receive FIFO Occupancy Register (read only) */
+#define HWABR __REG(0x41600028) /* Auto-Baud Control Register (read/write) */
+#define HWACR __REG(0x4160002C) /* Auto-Baud Count Register (read only) */
+#define HWDLL __REG(0x41600000) /* Divisor Latch Low Register (DLAB = 1) (read/write) */
+#define HWDLH __REG(0x41600004) /* Divisor Latch High Register (DLAB = 1) (read/write) */
+
#define IER_DMAE (1 << 7) /* DMA Requests Enable */
#define IER_UUE (1 << 6) /* UART Unit Enable */
#define IER_NRZE (1 << 5) /* NRZ coding Enable */
#define SACR1_ENLBF (1 << 5) /* Enable Loopback */
#define SACR1_DRPL (1 << 4) /* Disable Replaying Function */
#define SACR1_DREC (1 << 3) /* Disable Recording Function */
-#define SACR1_AMSL (1 << 1) /* Specify Alternate Mode */
+#define SACR1_AMSL (1 << 0) /* Specify Alternate Mode */
#define SASR0_I2SOFF (1 << 7) /* Controller Status */
#define SASR0_ROR (1 << 6) /* Rx FIFO Overrun */
#define UDCCS_IO_RFS (1 << 0) /* Receive FIFO service */
#define UDCCS_IO_RPC (1 << 1) /* Receive packet complete */
-#define UDCCS_IO_ROF (1 << 3) /* Receive overflow */
+#define UDCCS_IO_ROF (1 << 2) /* Receive overflow */
#define UDCCS_IO_DME (1 << 3) /* DMA enable */
#define UDCCS_IO_RNE (1 << 6) /* Receive FIFO not empty */
#define UDCCS_IO_RSP (1 << 7) /* Receive short packet */
#define ICCR0_LBM (1 << 1) /* Loopback mode */
#define ICCR0_ITR (1 << 0) /* IrDA transmission */
-#ifdef CONFIG_PXA27x
#define ICCR2_RXP (1 << 3) /* Receive Pin Polarity select */
#define ICCR2_TXP (1 << 2) /* Transmit Pin Polarity select */
#define ICCR2_TRIG (3 << 0) /* Receive FIFO Trigger threshold */
#define ICCR2_TRIG_8 (0 << 0) /* >= 8 bytes */
#define ICCR2_TRIG_16 (1 << 0) /* >= 16 bytes */
#define ICCR2_TRIG_32 (2 << 0) /* >= 32 bytes */
-#endif
#ifdef CONFIG_PXA27x
#define ICSR0_EOC (1 << 6) /* DMA End of Descriptor Chain */
#define GPIO40_FFDTR 40 /* FFUART data terminal Ready */
#define GPIO41_FFRTS 41 /* FFUART request to send */
#define GPIO42_BTRXD 42 /* BTUART receive data */
+#define GPIO42_HWRXD 42 /* HWUART receive data */
#define GPIO43_BTTXD 43 /* BTUART transmit data */
+#define GPIO43_HWTXD 43 /* HWUART transmit data */
#define GPIO44_BTCTS 44 /* BTUART clear to send */
+#define GPIO44_HWCTS 44 /* HWUART clear to send */
#define GPIO45_BTRTS 45 /* BTUART request to send */
+#define GPIO45_HWRTS 45 /* HWUART request to send */
#define GPIO45_AC97_SYSCLK 45 /* AC97 System Clock */
#define GPIO46_ICPRXD 46 /* ICP receive data */
#define GPIO46_STRXD 46 /* STD_UART receive data */
#define GPIO84_NSRXD 84 /* NSSP receive */
#define GPIO85_nPCE_1 85 /* Card Enable for Card Space (PXA27x) */
#define GPIO92_MMCDAT0 92 /* MMC DAT0 (PXA27x) */
+#define GPIO102_nPCE_1 102 /* PCMCIA (PXA27x) */
#define GPIO109_MMCDAT1 109 /* MMC DAT1 (PXA27x) */
#define GPIO110_MMCDAT2 110 /* MMC DAT2 (PXA27x) */
#define GPIO110_MMCCS0 110 /* MMC Chip Select 0 (PXA27x) */
#define GPIO40_FFDTR_MD (40 | GPIO_ALT_FN_2_OUT)
#define GPIO41_FFRTS_MD (41 | GPIO_ALT_FN_2_OUT)
#define GPIO42_BTRXD_MD (42 | GPIO_ALT_FN_1_IN)
+#define GPIO42_HWRXD_MD (42 | GPIO_ALT_FN_3_IN)
#define GPIO43_BTTXD_MD (43 | GPIO_ALT_FN_2_OUT)
+#define GPIO43_HWTXD_MD (43 | GPIO_ALT_FN_3_OUT)
#define GPIO44_BTCTS_MD (44 | GPIO_ALT_FN_1_IN)
+#define GPIO44_HWCTS_MD (44 | GPIO_ALT_FN_3_IN)
#define GPIO45_BTRTS_MD (45 | GPIO_ALT_FN_2_OUT)
+#define GPIO45_HWRTS_MD (45 | GPIO_ALT_FN_3_OUT)
#define GPIO45_SYSCLK_AC97_MD (45 | GPIO_ALT_FN_1_OUT)
#define GPIO46_ICPRXD_MD (46 | GPIO_ALT_FN_1_IN)
#define GPIO46_STRXD_MD (46 | GPIO_ALT_FN_2_IN)
#define GPIO47_ICPTXD_MD (47 | GPIO_ALT_FN_2_OUT)
#define GPIO47_STTXD_MD (47 | GPIO_ALT_FN_1_OUT)
#define GPIO48_nPOE_MD (48 | GPIO_ALT_FN_2_OUT)
+#define GPIO48_HWTXD_MD (48 | GPIO_ALT_FN_1_OUT)
+#define GPIO48_nPOE_MD (48 | GPIO_ALT_FN_2_OUT)
+#define GPIO49_HWRXD_MD (49 | GPIO_ALT_FN_1_IN)
#define GPIO49_nPWE_MD (49 | GPIO_ALT_FN_2_OUT)
#define GPIO50_nPIOR_MD (50 | GPIO_ALT_FN_2_OUT)
+#define GPIO50_HWCTS_MD (50 | GPIO_ALT_FN_1_IN)
+#define GPIO51_HWRTS_MD (51 | GPIO_ALT_FN_1_OUT)
#define GPIO51_nPIOW_MD (51 | GPIO_ALT_FN_2_OUT)
#define GPIO52_nPCE_1_MD (52 | GPIO_ALT_FN_2_OUT)
#define GPIO53_nPCE_2_MD (53 | GPIO_ALT_FN_2_OUT)
#define GPIO84_NSSP_RX (84 | GPIO_ALT_FN_2_IN)
#define GPIO85_nPCE_1_MD (85 | GPIO_ALT_FN_1_OUT)
#define GPIO92_MMCDAT0_MD (92 | GPIO_ALT_FN_1_OUT)
+#define GPIO102_nPCE_1_MD (102 | GPIO_ALT_FN_1_OUT)
#define GPIO104_pSKTSEL_MD (104 | GPIO_ALT_FN_1_OUT)
#define GPIO109_MMCDAT1_MD (109 | GPIO_ALT_FN_1_OUT)
#define GPIO110_MMCDAT2_MD (110 | GPIO_ALT_FN_1_OUT)
#define SSCR0_National (0x2 << 4) /* National Microwire */
#define SSCR0_ECS (1 << 6) /* External clock select */
#define SSCR0_SSE (1 << 7) /* Synchronous Serial Port Enable */
+#if defined(CONFIG_PXA25x)
#define SSCR0_SCR (0x0000ff00) /* Serial Clock Rate (mask) */
#define SSCR0_SerClkDiv(x) ((((x) - 2)/2) << 8) /* Divisor [2..512] */
+#elif defined(CONFIG_PXA27x)
+#define SSCR0_SCR (0x000fff00) /* Serial Clock Rate (mask) */
+#define SSCR0_SerClkDiv(x) (((x) - 1) << 8) /* Divisor [1..4096] */
+#define SSCR0_EDSS (1 << 20) /* Extended data size select */
+#define SSCR0_NCS (1 << 21) /* Network clock select */
+#define SSCR0_RIM (1 << 22) /* Receive FIFO overrrun interrupt mask */
+#define SSCR0_TUM (1 << 23) /* Transmit FIFO underrun interrupt mask */
+#define SSCR0_FRDC (0x07000000) /* Frame rate divider control (mask) */
+#define SSCR0_SlotsPerFrm(x) ((x) - 1) /* Time slots per frame [1..8] */
+#define SSCR0_ADC (1 << 30) /* Audio clock select */
+#define SSCR0_MOD (1 << 31) /* Mode (normal or network) */
+#endif
#define SSCR1_RIE (1 << 0) /* Receive FIFO Interrupt Enable */
#define SSCR1_TIE (1 << 1) /* Transmit FIFO Interrupt Enable */
#define SSSR_TINT (1 << 19) /* Receiver Time-out Interrupt */
#define SSSR_PINT (1 << 18) /* Peripheral Trailing Byte Interrupt */
+#define SSPSP_FSRT (1 << 25) /* Frame Sync Relative Timing */
#define SSPSP_DMYSTOP(x) (x << 23) /* Dummy Stop */
#define SSPSP_SFRMWDTH(x) (x << 16) /* Serial Frame Width */
#define SSPSP_SFRMDLY(x) (x << 9) /* Serial Frame Delay */
#if defined (CONFIG_PXA27x)
#define SSTO_P1 __REG(0x41000028) /* SSP Port 1 Time Out Register */
#define SSPSP_P1 __REG(0x4100002C) /* SSP Port 1 Programmable Serial Protocol */
+#define SSTSA_P1 __REG(0x41000030) /* SSP Port 1 Tx Timeslot Active */
+#define SSRSA_P1 __REG(0x41000034) /* SSP Port 1 Rx Timeslot Active */
+#define SSTSS_P1 __REG(0x41000038) /* SSP Port 1 Timeslot Status */
+#define SSACD_P1 __REG(0x4100003C) /* SSP Port 1 Audio Clock Divider */
#define SSCR0_P2 __REG(0x41700000) /* SSP Port 2 Control Register 0 */
#define SSCR1_P2 __REG(0x41700004) /* SSP Port 2 Control Register 1 */
#define SSSR_P2 __REG(0x41700008) /* SSP Port 2 Status Register */
#define SSDR_P2 __REG(0x41700010) /* (Write / Read) SSP Port 2 Data Write Register/SSP Data Read Register */
#define SSTO_P2 __REG(0x41700028) /* SSP Port 2 Time Out Register */
#define SSPSP_P2 __REG(0x4170002C) /* SSP Port 2 Programmable Serial Protocol */
+#define SSTSA_P2 __REG(0x41700030) /* SSP Port 2 Tx Timeslot Active */
+#define SSRSA_P2 __REG(0x41700034) /* SSP Port 2 Rx Timeslot Active */
+#define SSTSS_P2 __REG(0x41700038) /* SSP Port 2 Timeslot Status */
+#define SSACD_P2 __REG(0x4170003C) /* SSP Port 2 Audio Clock Divider */
#define SSCR0_P3 __REG(0x41900000) /* SSP Port 3 Control Register 0 */
#define SSCR1_P3 __REG(0x41900004) /* SSP Port 3 Control Register 1 */
#define SSSR_P3 __REG(0x41900008) /* SSP Port 3 Status Register */
#define SSDR_P3 __REG(0x41900010) /* (Write / Read) SSP Port 3 Data Write Register/SSP Data Read Register */
#define SSTO_P3 __REG(0x41900028) /* SSP Port 3 Time Out Register */
#define SSPSP_P3 __REG(0x4190002C) /* SSP Port 3 Programmable Serial Protocol */
+#define SSTSA_P3 __REG(0x41900030) /* SSP Port 3 Tx Timeslot Active */
+#define SSRSA_P3 __REG(0x41900034) /* SSP Port 3 Rx Timeslot Active */
+#define SSTSS_P3 __REG(0x41900038) /* SSP Port 3 Timeslot Status */
+#define SSACD_P3 __REG(0x4190003C) /* SSP Port 3 Audio Clock Divider */
#else /* PXA255 (only port 2) and PXA26x ports*/
#define SSTO_P1 __REG(0x41000028) /* SSP Port 1 Time Out Register */
#define SSPSP_P1 __REG(0x4100002C) /* SSP Port 1 Programmable Serial Protocol */
#define SSDR_P(x) (*(((x) == 1) ? &SSDR_P1 : ((x) == 2) ? &SSDR_P2 : ((x) == 3) ? &SSDR_P3 : NULL))
#define SSTO_P(x) (*(((x) == 1) ? &SSTO_P1 : ((x) == 2) ? &SSTO_P2 : ((x) == 3) ? &SSTO_P3 : NULL))
#define SSPSP_P(x) (*(((x) == 1) ? &SSPSP_P1 : ((x) == 2) ? &SSPSP_P2 : ((x) == 3) ? &SSPSP_P3 : NULL))
+#define SSTSA_P(x) (*(((x) == 1) ? &SSTSA_P1 : ((x) == 2) ? &SSTSA_P2 : ((x) == 3) ? &SSTSA_P3 : NULL))
+#define SSRSA_P(x) (*(((x) == 1) ? &SSRSA_P1 : ((x) == 2) ? &SSRSA_P2 : ((x) == 3) ? &SSRSA_P3 : NULL))
+#define SSTSS_P(x) (*(((x) == 1) ? &SSTSS_P1 : ((x) == 2) ? &SSTSS_P2 : ((x) == 3) ? &SSTSS_P3 : NULL))
+#define SSACD_P(x) (*(((x) == 1) ? &SSACD_P1 : ((x) == 2) ? &SSACD_P2 : ((x) == 3) ? &SSACD_P3 : NULL))
/*
* MultiMediaCard (MMC) controller
#define CKEN7_BTUART (1 << 7) /* BTUART Unit Clock Enable */
#define CKEN6_FFUART (1 << 6) /* FFUART Unit Clock Enable */
#define CKEN5_STUART (1 << 5) /* STUART Unit Clock Enable */
+#define CKEN4_HWUART (1 << 4) /* HWUART Unit Clock Enable */
#define CKEN4_SSP3 (1 << 4) /* SSP3 Unit Clock Enable */
#define CKEN3_SSP (1 << 3) /* SSP Unit Clock Enable */
#define CKEN3_SSP2 (1 << 3) /* SSP2 Unit Clock Enable */
#ifdef CONFIG_PXA27x
+#define ARB_CNTRL __REG(0x48000048) /* Arbiter Control Register */
+
+#define ARB_DMA_SLV_PARK (1<<31) /* Be parked with DMA slave when idle */
+#define ARB_CI_PARK (1<<30) /* Be parked with Camera Interface when idle */
+#define ARB_EX_MEM_PARK (1<<29) /* Be parked with external MEMC when idle */
+#define ARB_INT_MEM_PARK (1<<28) /* Be parked with internal MEMC when idle */
+#define ARB_USB_PARK (1<<27) /* Be parked with USB when idle */
+#define ARB_LCD_PARK (1<<26) /* Be parked with LCD when idle */
+#define ARB_DMA_PARK (1<<25) /* Be parked with DMA when idle */
+#define ARB_CORE_PARK (1<<24) /* Be parked with core when idle */
+#define ARB_LOCK_FLAG (1<<23) /* Only Locking masters gain access to the bus */
+
/*
* Keypad
*/
#define CICR1_TBIT (1 << 31) /* Transparency bit */
#define CICR1_RGBT_CONV (0x3 << 30) /* RGBT conversion mask */
-#define CICR1_PPL (0x3f << 15) /* Pixels per line mask */
+#define CICR1_PPL (0x7ff << 15) /* Pixels per line mask */
#define CICR1_RGB_CONV (0x7 << 12) /* RGB conversion mask */
#define CICR1_RGB_F (1 << 11) /* RGB format */
#define CICR1_YCBCR_F (1 << 10) /* YCbCr format */
#define CICR3_VSW (0x3f << 10) /* Vertical sync pulse width mask */
#define CICR3_BFPW (0x3f << 3) /* Beginning-of-frame pixel clock
wait count mask */
-#define CICR3_LPF (0x3ff << 0) /* Lines per frame mask */
+#define CICR3_LPF (0x7ff << 0) /* Lines per frame mask */
#define CICR4_MCLK_DLY (0x3 << 24) /* MCLK Data Capture Delay mask */
#define CICR4_PCLK_EN (1 << 23) /* Pixel clock enable */
#define CISR_EOL (1 << 8) /* End of line */
#define CISR_PAR_ERR (1 << 7) /* Parity error */
#define CISR_CQD (1 << 6) /* Camera interface quick disable */
-#define CISR_SOF (1 << 5) /* Start of frame */
-#define CISR_CDD (1 << 4) /* Camera interface disable done */
+#define CISR_CDD (1 << 5) /* Camera interface disable done */
+#define CISR_SOF (1 << 4) /* Start of frame */
#define CISR_EOF (1 << 3) /* End of frame */
#define CISR_IFO_2 (1 << 2) /* FIFO overrun for Channel 2 */
#define CISR_IFO_1 (1 << 1) /* FIFO overrun for Channel 1 */
#endif
+/* PWRMODE register M field values */
+
+#define PWRMODE_IDLE 0x1
+#define PWRMODE_STANDBY 0x2
+#define PWRMODE_SLEEP 0x3
+#define PWRMODE_DEEPSLEEP 0x7
+
#endif