#include <linux/mtd/partitions.h>
#include <linux/device.h>
+#include <linux/i2c.h>
+#include <linux/leds.h>
#include <linux/spi/spi.h>
+#include <linux/usb/atmel_usba_udc.h>
/* USB Device */
struct at91_udc_data {
u8 vbus_pin; /* high == host powering us */
- u8 pullup_pin; /* high == D+ pulled up */
+ u8 pullup_pin; /* active == D+ pulled up */
+ u8 pullup_active_low; /* true == pullup_pin is active low */
};
extern void __init at91_add_device_udc(struct at91_udc_data *data);
+ /* USB High Speed Device */
+extern void __init at91_add_device_usba(struct usba_platform_data *data);
+
/* Compact Flash */
struct at91_cf_data {
u8 irq_pin; /* I/O IRQ */
};
extern void __init at91_add_device_eth(struct at91_eth_data *data);
-#if defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9263)
+#if defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9263) || defined(CONFIG_ARCH_AT91SAM9G20) || defined(CONFIG_ARCH_AT91CAP9)
#define eth_platform_data at91_eth_data
#endif
extern void __init at91_add_device_usbh(struct at91_usbh_data *data);
/* NAND / SmartMedia */
-struct at91_nand_data {
+struct atmel_nand_data {
u8 enable_pin; /* chip enable */
u8 det_pin; /* card detect */
u8 rdy_pin; /* ready/busy */
u8 bus_width_16; /* buswidth is 16 bit */
struct mtd_partition* (*partition_info)(int, int*);
};
-extern void __init at91_add_device_nand(struct at91_nand_data *data);
+extern void __init at91_add_device_nand(struct atmel_nand_data *data);
/* I2C*/
-extern void __init at91_add_device_i2c(void);
+extern void __init at91_add_device_i2c(struct i2c_board_info *devices, int nr_devices);
/* SPI */
extern void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices);
/* Serial */
+#define ATMEL_UART_CTS 0x01
+#define ATMEL_UART_RTS 0x02
+#define ATMEL_UART_DSR 0x04
+#define ATMEL_UART_DTR 0x08
+#define ATMEL_UART_DCD 0x10
+#define ATMEL_UART_RI 0x20
+
+extern void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins);
+extern void __init at91_set_serial_console(unsigned portnr);
+
struct at91_uart_config {
unsigned short console_tty; /* tty number of serial console */
unsigned short nr_tty; /* number of serial tty's */
short tty_map[]; /* map UART to tty number */
};
extern struct platform_device *atmel_default_console_device;
-extern void __init at91_init_serial(struct at91_uart_config *config);
+extern void __init __deprecated at91_init_serial(struct at91_uart_config *config);
struct atmel_uart_data {
short use_dma_tx; /* use transmit DMA? */
};
extern void __init at91_add_device_serial(void);
+/*
+ * SSC -- accessed through ssc_request(id). Drivers don't bind to SSC
+ * platform devices. Their SSC ID is part of their configuration data,
+ * along with information about which SSC signals they should use.
+ */
+#define ATMEL_SSC_TK 0x01
+#define ATMEL_SSC_TF 0x02
+#define ATMEL_SSC_TD 0x04
+#define ATMEL_SSC_TX (ATMEL_SSC_TK | ATMEL_SSC_TF | ATMEL_SSC_TD)
+
+#define ATMEL_SSC_RK 0x10
+#define ATMEL_SSC_RF 0x20
+#define ATMEL_SSC_RD 0x40
+#define ATMEL_SSC_RX (ATMEL_SSC_RK | ATMEL_SSC_RF | ATMEL_SSC_RD)
+
+extern void __init at91_add_device_ssc(unsigned id, unsigned pins);
+
/* LCD Controller */
struct atmel_lcdfb_info;
extern void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data);
};
extern void __init at91_add_device_ac97(struct atmel_ac97_data *data);
+ /* ISI */
+extern void __init at91_add_device_isi(void);
+
/* LEDs */
-extern u8 at91_leds_cpu;
-extern u8 at91_leds_timer;
extern void __init at91_init_leds(u8 cpu_led, u8 timer_led);
+extern void __init at91_gpio_leds(struct gpio_led *leds, int nr);
/* FIXME: this needs a better location, but gets stuff building again */
extern int at91_suspend_entering_slow_clock(void);