/* to make sure it doesn't hog all of the bandwidth */
#define DEPTH_INTERVAL 5
-static inline void restart_timer(struct uhci_hcd *uhci)
-{
- mod_timer(&uhci->stall_timer, jiffies + msecs_to_jiffies(100));
-}
-
-#include "uhci-hub.c"
#include "uhci-debug.c"
#include "uhci-q.c"
+#include "uhci-hub.c"
+
+extern void uhci_reset_hc(struct pci_dev *pdev, unsigned long base);
+extern int uhci_check_and_reset_hc(struct pci_dev *pdev, unsigned long base);
/*
- * Make sure the controller is completely inactive, unable to
- * generate interrupts or do DMA.
+ * Finish up a host controller reset and update the recorded state.
*/
-static void reset_hc(struct uhci_hcd *uhci)
+static void finish_reset(struct uhci_hcd *uhci)
{
- /* Turn off PIRQ enable and SMI enable. (This also turns off the
- * BIOS's USB Legacy Support.) Turn off all the R/WC bits too.
- */
- pci_write_config_word(to_pci_dev(uhci_dev(uhci)), USBLEGSUP,
- USBLEGSUP_RWC);
-
- /* Reset the HC - this will force us to get a
- * new notification of any already connected
- * ports due to the virtual disconnect that it
- * implies.
- */
- outw(USBCMD_HCRESET, uhci->io_addr + USBCMD);
- mb();
- udelay(5);
- if (inw(uhci->io_addr + USBCMD) & USBCMD_HCRESET)
- dev_warn(uhci_dev(uhci), "HCRESET not completed yet!\n");
+ int port;
- /* Just to be safe, disable interrupt requests and
- * make sure the controller is stopped.
+ /* HCRESET doesn't affect the Suspend, Reset, and Resume Detect
+ * bits in the port status and control registers.
+ * We have to clear them by hand.
*/
- outw(0, uhci->io_addr + USBINTR);
- outw(0, uhci->io_addr + USBCMD);
+ for (port = 0; port < uhci->rh_numports; ++port)
+ outw(0, uhci->io_addr + USBPORTSC1 + (port * 2));
uhci->port_c_suspend = uhci->suspended_ports =
uhci->resuming_ports = 0;
/*
* Last rites for a defunct/nonfunctional controller
+ * or one we don't want to use any more.
*/
static void hc_died(struct uhci_hcd *uhci)
{
- reset_hc(uhci);
+ uhci_reset_hc(to_pci_dev(uhci_dev(uhci)), uhci->io_addr);
+ finish_reset(uhci);
uhci->hc_inaccessible = 1;
- del_timer(&uhci->stall_timer);
}
/*
*/
static void check_and_reset_hc(struct uhci_hcd *uhci)
{
- u16 legsup;
- unsigned int cmd, intr;
-
- /*
- * When restarting a suspended controller, we expect all the
- * settings to be the same as we left them:
- *
- * PIRQ and SMI disabled, no R/WC bits set in USBLEGSUP;
- * Controller is stopped and configured with EGSM set;
- * No interrupts enabled except possibly Resume Detect.
- *
- * If any of these conditions are violated we do a complete reset.
- */
- pci_read_config_word(to_pci_dev(uhci_dev(uhci)), USBLEGSUP, &legsup);
- if (legsup & ~USBLEGSUP_RO) {
- dev_dbg(uhci_dev(uhci), "%s: legsup = 0x%04x\n",
- __FUNCTION__, legsup);
- goto reset_needed;
- }
-
- cmd = inw(uhci->io_addr + USBCMD);
- if ((cmd & USBCMD_RS) || !(cmd & USBCMD_CF) || !(cmd & USBCMD_EGSM)) {
- dev_dbg(uhci_dev(uhci), "%s: cmd = 0x%04x\n",
- __FUNCTION__, cmd);
- goto reset_needed;
- }
-
- intr = inw(uhci->io_addr + USBINTR);
- if (intr & (~USBINTR_RESUME)) {
- dev_dbg(uhci_dev(uhci), "%s: intr = 0x%04x\n",
- __FUNCTION__, intr);
- goto reset_needed;
- }
- return;
-
-reset_needed:
- dev_dbg(uhci_dev(uhci), "Performing full reset\n");
- reset_hc(uhci);
+ if (uhci_check_and_reset_hc(to_pci_dev(uhci_dev(uhci)), uhci->io_addr))
+ finish_reset(uhci);
}
/*
outb(USBSOF_DEFAULT, uhci->io_addr + USBSOF);
/* Store the frame list base address */
- outl(uhci->fl->dma_handle, uhci->io_addr + USBFLBASEADD);
+ outl(uhci->frame_dma_handle, uhci->io_addr + USBFLBASEADD);
/* Set the current frame number */
outw(uhci->frame_number, uhci->io_addr + USBFRNUM);
/* Enable resume-detect interrupts if they work.
* Then enter Global Suspend mode, still configured.
*/
- int_enable = (resume_detect_interrupts_are_broken(uhci) ?
- 0 : USBINTR_RESUME);
+ uhci->working_RD = 1;
+ int_enable = USBINTR_RESUME;
+ if (resume_detect_interrupts_are_broken(uhci)) {
+ uhci->working_RD = int_enable = 0;
+ }
outw(int_enable, uhci->io_addr + USBINTR);
outw(USBCMD_EGSM | USBCMD_CF, uhci->io_addr + USBCMD);
mb();
uhci->rh_state = new_state;
uhci->is_stopped = UHCI_IS_STOPPED;
- del_timer(&uhci->stall_timer);
uhci_to_hcd(uhci)->poll_rh = !int_enable;
uhci_scan_schedule(uhci, NULL);
mb();
uhci->rh_state = UHCI_RH_RUNNING;
uhci_to_hcd(uhci)->poll_rh = 1;
- restart_timer(uhci);
}
static void wakeup_rh(struct uhci_hcd *uhci)
mod_timer(&uhci_to_hcd(uhci)->rh_timer, jiffies);
}
-static void stall_callback(unsigned long _uhci)
-{
- struct uhci_hcd *uhci = (struct uhci_hcd *) _uhci;
- unsigned long flags;
-
- spin_lock_irqsave(&uhci->lock, flags);
- uhci_scan_schedule(uhci, NULL);
- check_fsbr(uhci);
-
- if (!uhci->is_stopped)
- restart_timer(uhci);
- spin_unlock_irqrestore(&uhci->lock, flags);
-}
-
static irqreturn_t uhci_irq(struct usb_hcd *hcd, struct pt_regs *regs)
{
struct uhci_hcd *uhci = hcd_to_uhci(hcd);
"host controller halted, "
"very bad!\n");
hc_died(uhci);
- spin_unlock_irqrestore(&uhci->lock, flags);
- return IRQ_HANDLED;
+
+ /* Force a callback in case there are
+ * pending unlinks */
+ mod_timer(&hcd->rh_timer, jiffies);
}
spin_unlock_irqrestore(&uhci->lock, flags);
}
if (status & USBSTS_RD)
usb_hcd_poll_rh_status(hcd);
-
- spin_lock_irqsave(&uhci->lock, flags);
- uhci_scan_schedule(uhci, regs);
- spin_unlock_irqrestore(&uhci->lock, flags);
+ else {
+ spin_lock_irqsave(&uhci->lock, flags);
+ uhci_scan_schedule(uhci, regs);
+ spin_unlock_irqrestore(&uhci->lock, flags);
+ }
return IRQ_HANDLED;
}
int i;
for (i = 0; i < UHCI_NUM_SKELQH; i++)
- if (uhci->skelqh[i]) {
- uhci_free_qh(uhci, uhci->skelqh[i]);
- uhci->skelqh[i] = NULL;
- }
+ uhci_free_qh(uhci, uhci->skelqh[i]);
- if (uhci->term_td) {
- uhci_free_td(uhci, uhci->term_td);
- uhci->term_td = NULL;
- }
+ uhci_free_td(uhci, uhci->term_td);
- if (uhci->qh_pool) {
- dma_pool_destroy(uhci->qh_pool);
- uhci->qh_pool = NULL;
- }
+ dma_pool_destroy(uhci->qh_pool);
- if (uhci->td_pool) {
- dma_pool_destroy(uhci->td_pool);
- uhci->td_pool = NULL;
- }
+ dma_pool_destroy(uhci->td_pool);
- if (uhci->fl) {
- dma_free_coherent(uhci_dev(uhci), sizeof(*uhci->fl),
- uhci->fl, uhci->fl->dma_handle);
- uhci->fl = NULL;
- }
+ kfree(uhci->frame_cpu);
- if (uhci->dentry) {
- debugfs_remove(uhci->dentry);
- uhci->dentry = NULL;
- }
+ dma_free_coherent(uhci_dev(uhci),
+ UHCI_NUMFRAMES * sizeof(*uhci->frame),
+ uhci->frame, uhci->frame_dma_handle);
+
+ debugfs_remove(uhci->dentry);
}
static int uhci_reset(struct usb_hcd *hcd)
{
struct uhci_hcd *uhci = hcd_to_uhci(hcd);
+ unsigned io_size = (unsigned) hcd->rsrc_len;
+ int port;
uhci->io_addr = (unsigned long) hcd->rsrc_start;
+ /* The UHCI spec says devices must have 2 ports, and goes on to say
+ * they may have more but gives no way to determine how many there
+ * are. However according to the UHCI spec, Bit 7 of the port
+ * status and control register is always set to 1. So we try to
+ * use this to our advantage. Another common failure mode when
+ * a nonexistent register is addressed is to return all ones, so
+ * we test for that also.
+ */
+ for (port = 0; port < (io_size - USBPORTSC1) / 2; port++) {
+ unsigned int portstatus;
+
+ portstatus = inw(uhci->io_addr + USBPORTSC1 + (port * 2));
+ if (!(portstatus & 0x0080) || portstatus == 0xffff)
+ break;
+ }
+ if (debug)
+ dev_info(uhci_dev(uhci), "detected %d ports\n", port);
+
+ /* Anything greater than 7 is weird so we'll ignore it. */
+ if (port > UHCI_RH_MAXCHILD) {
+ dev_info(uhci_dev(uhci), "port count misdetected? "
+ "forcing to 2 ports\n");
+ port = 2;
+ }
+ uhci->rh_numports = port;
+
/* Kick BIOS off this hardware and reset if the controller
* isn't already safely quiescent.
*/
return 0;
}
+/* Make sure the controller is quiescent and that we're not using it
+ * any more. This is mainly for the benefit of programs which, like kexec,
+ * expect the hardware to be idle: not doing DMA or generating IRQs.
+ *
+ * This routine may be called in a damaged or failing kernel. Hence we
+ * do not acquire the spinlock before shutting down the controller.
+ */
+static void uhci_shutdown(struct pci_dev *pdev)
+{
+ struct usb_hcd *hcd = (struct usb_hcd *) pci_get_drvdata(pdev);
+
+ hc_died(hcd_to_uhci(hcd));
+}
+
/*
* Allocate a frame list, and then setup the skeleton
*
{
struct uhci_hcd *uhci = hcd_to_uhci(hcd);
int retval = -EBUSY;
- int i, port;
- unsigned io_size;
- dma_addr_t dma_handle;
- struct usb_device *udev;
+ int i;
struct dentry *dentry;
- io_size = (unsigned) hcd->rsrc_len;
hcd->uses_new_polling = 1;
if (pci_find_capability(to_pci_dev(uhci_dev(uhci)), PCI_CAP_ID_PM))
hcd->can_wakeup = 1; /* Assume it supports PME# */
init_waitqueue_head(&uhci->waitqh);
- init_timer(&uhci->stall_timer);
- uhci->stall_timer.function = stall_callback;
- uhci->stall_timer.data = (unsigned long) uhci;
-
- uhci->fl = dma_alloc_coherent(uhci_dev(uhci), sizeof(*uhci->fl),
- &dma_handle, 0);
- if (!uhci->fl) {
+ uhci->frame = dma_alloc_coherent(uhci_dev(uhci),
+ UHCI_NUMFRAMES * sizeof(*uhci->frame),
+ &uhci->frame_dma_handle, 0);
+ if (!uhci->frame) {
dev_err(uhci_dev(uhci), "unable to allocate "
"consistent memory for frame list\n");
- goto err_alloc_fl;
+ goto err_alloc_frame;
}
+ memset(uhci->frame, 0, UHCI_NUMFRAMES * sizeof(*uhci->frame));
- memset((void *)uhci->fl, 0, sizeof(*uhci->fl));
-
- uhci->fl->dma_handle = dma_handle;
+ uhci->frame_cpu = kcalloc(UHCI_NUMFRAMES, sizeof(*uhci->frame_cpu),
+ GFP_KERNEL);
+ if (!uhci->frame_cpu) {
+ dev_err(uhci_dev(uhci), "unable to allocate "
+ "memory for frame pointers\n");
+ goto err_alloc_frame_cpu;
+ }
uhci->td_pool = dma_pool_create("uhci_td", uhci_dev(uhci),
sizeof(struct uhci_td), 16, 0);
goto err_create_qh_pool;
}
- /* Initialize the root hub */
-
- /* UHCI specs says devices must have 2 ports, but goes on to say */
- /* they may have more but give no way to determine how many they */
- /* have. However, according to the UHCI spec, Bit 7 is always set */
- /* to 1. So we try to use this to our advantage */
- for (port = 0; port < (io_size - 0x10) / 2; port++) {
- unsigned int portstatus;
-
- portstatus = inw(uhci->io_addr + 0x10 + (port * 2));
- if (!(portstatus & 0x0080))
- break;
- }
- if (debug)
- dev_info(uhci_dev(uhci), "detected %d ports\n", port);
-
- /* This is experimental so anything less than 2 or greater than 8 is */
- /* something weird and we'll ignore it */
- if (port < 2 || port > UHCI_RH_MAXCHILD) {
- dev_info(uhci_dev(uhci), "port count misdetected? "
- "forcing to 2 ports\n");
- port = 2;
- }
-
- uhci->rh_numports = port;
-
- udev = usb_alloc_dev(NULL, &hcd->self, 0);
- if (!udev) {
- dev_err(uhci_dev(uhci), "unable to allocate root hub\n");
- goto err_alloc_root_hub;
- }
-
- uhci->term_td = uhci_alloc_td(uhci, udev);
+ uhci->term_td = uhci_alloc_td(uhci);
if (!uhci->term_td) {
dev_err(uhci_dev(uhci), "unable to allocate terminating TD\n");
goto err_alloc_term_td;
}
for (i = 0; i < UHCI_NUM_SKELQH; i++) {
- uhci->skelqh[i] = uhci_alloc_qh(uhci, udev);
+ uhci->skelqh[i] = uhci_alloc_qh(uhci);
if (!uhci->skelqh[i]) {
dev_err(uhci_dev(uhci), "unable to allocate QH\n");
goto err_alloc_skelqh;
irq = 7;
/* Only place we don't use the frame list routines */
- uhci->fl->frame[i] = UHCI_PTR_QH |
+ uhci->frame[i] = UHCI_PTR_QH |
cpu_to_le32(uhci->skelqh[irq]->dma_handle);
}
configure_hc(uhci);
start_rh(uhci);
-
- udev->speed = USB_SPEED_FULL;
-
- if (usb_hcd_register_root_hub(udev, hcd) != 0) {
- dev_err(uhci_dev(uhci), "unable to start root hub\n");
- retval = -ENOMEM;
- goto err_start_root_hub;
- }
-
return 0;
/*
* error exits:
*/
-err_start_root_hub:
- reset_hc(uhci);
- del_timer_sync(&uhci->stall_timer);
-
err_alloc_skelqh:
- for (i = 0; i < UHCI_NUM_SKELQH; i++)
- if (uhci->skelqh[i]) {
+ for (i = 0; i < UHCI_NUM_SKELQH; i++) {
+ if (uhci->skelqh[i])
uhci_free_qh(uhci, uhci->skelqh[i]);
- uhci->skelqh[i] = NULL;
- }
+ }
uhci_free_td(uhci, uhci->term_td);
- uhci->term_td = NULL;
err_alloc_term_td:
- usb_put_dev(udev);
-
-err_alloc_root_hub:
dma_pool_destroy(uhci->qh_pool);
- uhci->qh_pool = NULL;
err_create_qh_pool:
dma_pool_destroy(uhci->td_pool);
- uhci->td_pool = NULL;
err_create_td_pool:
- dma_free_coherent(uhci_dev(uhci), sizeof(*uhci->fl),
- uhci->fl, uhci->fl->dma_handle);
- uhci->fl = NULL;
+ kfree(uhci->frame_cpu);
+
+err_alloc_frame_cpu:
+ dma_free_coherent(uhci_dev(uhci),
+ UHCI_NUMFRAMES * sizeof(*uhci->frame),
+ uhci->frame, uhci->frame_dma_handle);
-err_alloc_fl:
+err_alloc_frame:
debugfs_remove(uhci->dentry);
- uhci->dentry = NULL;
err_create_debug_entry:
return retval;
struct uhci_hcd *uhci = hcd_to_uhci(hcd);
spin_lock_irq(&uhci->lock);
- reset_hc(uhci);
+ if (!uhci->hc_inaccessible)
+ hc_died(uhci);
uhci_scan_schedule(uhci, NULL);
spin_unlock_irq(&uhci->lock);
- del_timer_sync(&uhci->stall_timer);
release_uhci(uhci);
}
if (uhci->hc_inaccessible) /* Dead or already suspended */
goto done;
-#ifndef CONFIG_USB_SUSPEND
- /* Otherwise this would never happen */
- suspend_rh(uhci, UHCI_RH_SUSPENDED);
-#endif
-
if (uhci->rh_state > UHCI_RH_SUSPENDED) {
dev_warn(uhci_dev(uhci), "Root hub isn't suspended!\n");
hcd->state = HC_STATE_RUNNING;
*/
pci_write_config_word(to_pci_dev(uhci_dev(uhci)), USBLEGSUP, 0);
uhci->hc_inaccessible = 1;
+ hcd->poll_rh = 0;
/* FIXME: Enable non-PME# remote wakeup? */
done:
spin_unlock_irq(&uhci->lock);
- if (rc == 0)
- del_timer_sync(&hcd->rh_timer);
return rc;
}
check_and_reset_hc(uhci);
configure_hc(uhci);
-#ifndef CONFIG_USB_SUSPEND
- /* Otherwise this would never happen */
- wakeup_rh(uhci);
-#endif
if (uhci->rh_state == UHCI_RH_RESET)
suspend_rh(uhci, UHCI_RH_SUSPENDED);
spin_unlock_irq(&uhci->lock);
- if (hcd->poll_rh)
+ if (!uhci->working_RD) {
+ /* Suspended root hub needs to be polled */
+ hcd->poll_rh = 1;
usb_hcd_poll_rh_status(hcd);
+ }
return 0;
}
#endif
#ifdef CONFIG_PM
.suspend = uhci_suspend,
.resume = uhci_resume,
- .hub_suspend = uhci_rh_suspend,
- .hub_resume = uhci_rh_resume,
+ .bus_suspend = uhci_rh_suspend,
+ .bus_resume = uhci_rh_resume,
#endif
.stop = uhci_stop,
.probe = usb_hcd_pci_probe,
.remove = usb_hcd_pci_remove,
+ .shutdown = uhci_shutdown,
#ifdef CONFIG_PM
.suspend = usb_hcd_pci_suspend,
projects / linux-2.6 / blobdiff