#ifdef CONFIG_PM
+/* Try to identify which devices need USB-PERSIST handling */
+static int persistent_device(struct usb_device *udev)
+{
+ int i;
+ int retval;
+ struct usb_host_config *actconfig;
+
+ /* Explicitly not marked persistent? */
+ if (!udev->persist_enabled)
+ return 0;
+
+ /* No active config? */
+ actconfig = udev->actconfig;
+ if (!actconfig)
+ return 0;
+
+ /* FIXME! We should check whether it's open here or not! */
+
+ /*
+ * Check that all the interface drivers have a
+ * 'reset_resume' entrypoint
+ */
+ retval = 0;
+ for (i = 0; i < actconfig->desc.bNumInterfaces; i++) {
+ struct usb_interface *intf;
+ struct usb_driver *driver;
+
+ intf = actconfig->interface[i];
+ if (!intf->dev.driver)
+ continue;
+ driver = to_usb_driver(intf->dev.driver);
+ if (!driver->reset_resume)
+ return 0;
+ /*
+ * We have at least one driver, and that one
+ * has a reset_resume method.
+ */
+ retval = 1;
+ }
+ return retval;
+}
+
static void hub_restart(struct usb_hub *hub, int type)
{
struct usb_device *hdev = hub->hdev;
}
/* Was the power session lost while we were suspended? */
- switch (type) {
- case HUB_RESET_RESUME:
- portstatus = 0;
- portchange = USB_PORT_STAT_C_CONNECTION;
- break;
+ status = hub_port_status(hub, port1, &portstatus, &portchange);
- case HUB_RESET:
- case HUB_RESUME:
- status = hub_port_status(hub, port1,
- &portstatus, &portchange);
- break;
- }
+ /* If the device is gone, khubd will handle it later */
+ if (status == 0 && !(portstatus & USB_PORT_STAT_CONNECTION))
+ continue;
/* For "USB_PERSIST"-enabled children we must
* mark the child device for reset-resume and
* turn off the various status changes to prevent
* khubd from disconnecting it later.
*/
- if (udev->persist_enabled && status == 0 &&
- !(portstatus & USB_PORT_STAT_ENABLE)) {
+ if (status == 0 && !(portstatus & USB_PORT_STAT_ENABLE) &&
+ persistent_device(udev)) {
if (portchange & USB_PORT_STAT_C_ENABLE)
clear_port_feature(hub->hdev, port1,
USB_PORT_FEAT_C_ENABLE);
}
clear_bit(port1, hub->busy_bits);
+ if (!hub->hdev->parent && !hub->busy_bits[0])
+ usb_enable_root_hub_irq(hub->hdev->bus);
if (status == 0)
status = finish_port_resume(udev);
hub->activating = 0;
+ /* If this is a root hub, tell the HCD it's okay to
+ * re-enable port-change interrupts now. */
+ if (!hdev->parent && !hub->busy_bits[0])
+ usb_enable_root_hub_irq(hdev->bus);
+
loop_autopm:
/* Allow autosuspend if we're not going to run again */
if (list_empty(&hub->event_list))
break;
}
clear_bit(port1, parent_hub->busy_bits);
+ if (!parent_hdev->parent && !parent_hub->busy_bits[0])
+ usb_enable_root_hub_irq(parent_hdev->bus);
if (ret < 0)
goto re_enumerate;