#define UART_PUT_CHAR(p, c) __raw_writel((c), (p)->membase + IO_DATA_REG_OFFSET)
#define UART_GET_FIFO_CNT(p) __raw_readl((p)->membase + IO_DCOUNT_REG_OFFSET)
-#define GET_MUX_PORTS(iodc_data) ((((iodc_data)[4] & 0xf0) >> 4) * 8) + 8
+
+/**
+ * get_mux_port_count - Get the number of available ports on the Mux.
+ * @dev: The parisc device.
+ *
+ * This function is used to determine the number of ports the Mux
+ * supports. The IODC data reports the number of ports the Mux
+ * can support, but there are cases where not all the Mux ports
+ * are connected. This function can override the IODC and
+ * return the true port count.
+ */
+static int __init get_mux_port_count(struct parisc_device *dev)
+{
+ int status;
+ u8 iodc_data[32];
+ unsigned long bytecnt;
+
+ /* If this is the built-in Mux for the K-Class (Eole CAP/MUX),
+ * we only need to allocate resources for 1 port since the
+ * other 7 ports are not connected.
+ */
+ if(dev->id.hversion == 0x15)
+ return 1;
+
+ status = pdc_iodc_read(&bytecnt, dev->hpa.start, 0, iodc_data, 32);
+ BUG_ON(status != PDC_OK);
+
+ /* Return the number of ports specified in the iodc data. */
+ return ((((iodc_data)[4] & 0xf0) >> 4) * 8) + 8;
+}
/**
* mux_tx_empty - Check if the transmitter fifo is empty.
* The Serial Mux does not support this function.
*/
static void
-mux_set_termios(struct uart_port *port, struct termios *termios,
- struct termios *old)
+mux_set_termios(struct uart_port *port, struct ktermios *termios,
+ struct ktermios *old)
{
}
*/
static int __init mux_probe(struct parisc_device *dev)
{
- int i, status, port_count;
- u8 iodc_data[32];
- unsigned long bytecnt;
-
- status = pdc_iodc_read(&bytecnt, dev->hpa.start, 0, iodc_data, 32);
- if(status != PDC_OK) {
- printk(KERN_ERR "Serial mux: Unable to read IODC.\n");
- return 1;
- }
+ int i, status;
- port_count = GET_MUX_PORTS(iodc_data);
- printk(KERN_INFO "Serial mux driver (%d ports) Revision: 0.5\n", port_count);
+ int port_count = get_mux_port_count(dev);
+ printk(KERN_INFO "Serial mux driver (%d ports) Revision: 0.6\n", port_count);
dev_set_drvdata(&dev->dev, (void *)(long)port_count);
request_mem_region(dev->hpa.start + MUX_OFFSET,
*/
port->timeout = HZ / 50;
spin_lock_init(&port->lock);
+
status = uart_add_one_port(&mux_driver, port);
BUG_ON(status);
}
static int __devexit mux_remove(struct parisc_device *dev)
{
- int i;
+ int i, j;
int port_count = (long)dev_get_drvdata(&dev->dev);
- /* Delete the Mux timer. */
- del_timer(&mux_timer);
-
/* Find Port 0 for this card in the mux_ports list. */
for(i = 0; i < port_cnt; ++i) {
if(mux_ports[i].port.mapbase == dev->hpa.start + MUX_OFFSET)
BUG_ON(i + port_count > port_cnt);
/* Release the resources associated with each port on the device. */
- for(; i < port_count; ++i) {
+ for(j = 0; j < port_count; ++j, ++i) {
struct uart_port *port = &mux_ports[i].port;
uart_remove_one_port(&mux_driver, port);
return 0;
}
+/* Hack. This idea was taken from the 8250_gsc.c on how to properly order
+ * the serial port detection in the proper order. The idea is we always
+ * want the builtin mux to be detected before addin mux cards, so we
+ * specifically probe for the builtin mux cards first.
+ *
+ * This table only contains the parisc_device_id of known builtin mux
+ * devices. All other mux cards will be detected by the generic mux_tbl.
+ */
+static struct parisc_device_id builtin_mux_tbl[] = {
+ { HPHW_A_DIRECT, HVERSION_REV_ANY_ID, 0x15, 0x0000D }, /* All K-class */
+ { HPHW_A_DIRECT, HVERSION_REV_ANY_ID, 0x44, 0x0000D }, /* E35, E45, and E55 */
+ { 0, }
+};
+
static struct parisc_device_id mux_tbl[] = {
{ HPHW_A_DIRECT, HVERSION_REV_ANY_ID, HVERSION_ANY_ID, 0x0000D },
{ 0, }
};
+MODULE_DEVICE_TABLE(parisc, builtin_mux_tbl);
MODULE_DEVICE_TABLE(parisc, mux_tbl);
+static struct parisc_driver builtin_serial_mux_driver = {
+ .name = "builtin_serial_mux",
+ .id_table = builtin_mux_tbl,
+ .probe = mux_probe,
+ .remove = __devexit_p(mux_remove),
+};
+
static struct parisc_driver serial_mux_driver = {
.name = "serial_mux",
.id_table = mux_tbl,
};
/**
- * mux_init - Serial MUX initalization procedure.
+ * mux_init - Serial MUX initialization procedure.
*
* Register the Serial MUX driver.
*/
static int __init mux_init(void)
{
- int status = register_parisc_driver(&serial_mux_driver);
+ register_parisc_driver(&builtin_serial_mux_driver);
+ register_parisc_driver(&serial_mux_driver);
if(port_cnt > 0) {
/* Start the Mux timer */
#endif
}
- return status;
+ return 0;
}
/**
#endif
}
+ unregister_parisc_driver(&builtin_serial_mux_driver);
unregister_parisc_driver(&serial_mux_driver);
uart_unregister_driver(&mux_driver);
}