* linux/drivers/char/at91_serial.c
*
* Driver for Atmel AT91RM9200 Serial ports
- *
* Copyright (C) 2003 Rick Bronson
*
* Based on drivers/char/serial_sa1100.c, by Deep Blue Solutions Ltd.
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*
*/
-#include <linux/config.h>
#include <linux/module.h>
#include <linux/tty.h>
#include <linux/ioport.h>
#include <linux/slab.h>
#include <linux/init.h>
#include <linux/serial.h>
+#include <linux/clk.h>
#include <linux/console.h>
#include <linux/sysrq.h>
#include <linux/tty_flip.h>
+#include <linux/platform_device.h>
#include <asm/io.h>
#include <asm/arch/at91rm9200_usart.h>
-#include <asm/mach/serial_at91rm9200.h>
+#include <asm/arch/at91rm9200_pdc.h>
+#include <asm/mach/serial_at91.h>
#include <asm/arch/board.h>
-#include <asm/arch/pio.h>
-
+#include <asm/arch/system.h>
#if defined(CONFIG_SERIAL_AT91_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
#define SUPPORT_SYSRQ
#endif
-#define AT91_VA_BASE_DBGU ((unsigned long) AT91_VA_BASE_SYS + AT91_DBGU)
#define AT91_ISR_PASS_LIMIT 256
#define UART_PUT_CR(port,v) writel(v, (port)->membase + AT91_US_CR)
/* PDC registers */
#define UART_PUT_PTCR(port,v) writel(v, (port)->membase + AT91_PDC_PTCR)
+#define UART_GET_PTSR(port) readl((port)->membase + AT91_PDC_PTSR)
+
#define UART_PUT_RPR(port,v) writel(v, (port)->membase + AT91_PDC_RPR)
+#define UART_GET_RPR(port) readl((port)->membase + AT91_PDC_RPR)
#define UART_PUT_RCR(port,v) writel(v, (port)->membase + AT91_PDC_RCR)
-#define UART_GET_RCR(port) readl((port)->membase + AT91_PDC_RCR)
#define UART_PUT_RNPR(port,v) writel(v, (port)->membase + AT91_PDC_RNPR)
#define UART_PUT_RNCR(port,v) writel(v, (port)->membase + AT91_PDC_RNCR)
+#define UART_PUT_TPR(port,v) writel(v, (port)->membase + AT91_PDC_TPR)
+#define UART_PUT_TCR(port,v) writel(v, (port)->membase + AT91_PDC_TCR)
+//#define UART_PUT_TNPR(port,v) writel(v, (port)->membase + AT91_PDC_TNPR)
+//#define UART_PUT_TNCR(port,v) writel(v, (port)->membase + AT91_PDC_TNCR)
static int (*at91_open)(struct uart_port *);
static void (*at91_close)(struct uart_port *);
+/*
+ * We wrap our port structure around the generic uart_port.
+ */
+struct at91_uart_port {
+ struct uart_port uart; /* uart */
+ struct clk *clk; /* uart clock */
+ unsigned short suspended; /* is port suspended? */
+};
+
+static struct at91_uart_port at91_ports[AT91_NR_UART];
+
#ifdef SUPPORT_SYSRQ
static struct console at91_console;
#endif
static void at91_set_mctrl(struct uart_port *port, u_int mctrl)
{
unsigned int control = 0;
+ unsigned int mode;
- /*
- * Errata #39: RTS0 is not internally connected to PA21. We need to drive
- * the pin manually.
- */
- if (port->mapbase == AT91_VA_BASE_US0) {
- if (mctrl & TIOCM_RTS)
- at91_sys_write(AT91_PIOA + PIO_CODR, AT91_PA21_RTS0);
- else
- at91_sys_write(AT91_PIOA + PIO_SODR, AT91_PA21_RTS0);
+ if (arch_identify() == ARCH_ID_AT91RM9200) {
+ /*
+ * AT91RM9200 Errata #39: RTS0 is not internally connected to PA21.
+ * We need to drive the pin manually.
+ */
+ if (port->mapbase == AT91_BASE_US0) {
+ if (mctrl & TIOCM_RTS)
+ at91_sys_write(AT91_PIOA + PIO_CODR, AT91_PA21_RTS0);
+ else
+ at91_sys_write(AT91_PIOA + PIO_SODR, AT91_PA21_RTS0);
+ }
}
if (mctrl & TIOCM_RTS)
else
control |= AT91_US_DTRDIS;
- UART_PUT_CR(port,control);
+ UART_PUT_CR(port, control);
+
+ /* Local loopback mode? */
+ mode = UART_GET_MR(port) & ~AT91_US_CHMODE;
+ if (mctrl & TIOCM_LOOP)
+ mode |= AT91_US_CHMODE_LOC_LOOP;
+ else
+ mode |= AT91_US_CHMODE_NORMAL;
+ UART_PUT_MR(port, mode);
}
/*
*/
static void at91_stop_tx(struct uart_port *port)
{
+ struct at91_uart_port *at91_port = (struct at91_uart_port *) port;
+
UART_PUT_IDR(port, AT91_US_TXRDY);
- port->read_status_mask &= ~AT91_US_TXRDY;
}
/*
*/
static void at91_start_tx(struct uart_port *port)
{
- port->read_status_mask |= AT91_US_TXRDY;
+ struct at91_uart_port *at91_port = (struct at91_uart_port *) port;
+
UART_PUT_IER(port, AT91_US_TXRDY);
}
*/
static void at91_stop_rx(struct uart_port *port)
{
+ struct at91_uart_port *at91_port = (struct at91_uart_port *) port;
+
UART_PUT_IDR(port, AT91_US_RXRDY);
}
*/
static void at91_enable_ms(struct uart_port *port)
{
- port->read_status_mask |= (AT91_US_RIIC | AT91_US_DSRIC | AT91_US_DCDIC | AT91_US_CTSIC);
UART_PUT_IER(port, AT91_US_RIIC | AT91_US_DSRIC | AT91_US_DCDIC | AT91_US_CTSIC);
}
struct tty_struct *tty = port->info->tty;
unsigned int status, ch, flg;
- status = UART_GET_CSR(port) & port->read_status_mask;
- while (status & (AT91_US_RXRDY)) {
+ status = UART_GET_CSR(port);
+ while (status & AT91_US_RXRDY) {
ch = UART_GET_CHAR(port);
port->icount.rx++;
* note that the error handling code is
* out of the main execution path
*/
- if (unlikely(status & (AT91_US_PARE | AT91_US_FRAME | AT91_US_OVRE))) {
+ if (unlikely(status & (AT91_US_PARE | AT91_US_FRAME | AT91_US_OVRE | AT91_US_RXBRK))) {
UART_PUT_CR(port, AT91_US_RSTSTA); /* clear error */
- if (status & (AT91_US_PARE))
+ if (status & AT91_US_RXBRK) {
+ status &= ~(AT91_US_PARE | AT91_US_FRAME); /* ignore side-effect */
+ port->icount.brk++;
+ if (uart_handle_break(port))
+ goto ignore_char;
+ }
+ if (status & AT91_US_PARE)
port->icount.parity++;
- if (status & (AT91_US_FRAME))
+ if (status & AT91_US_FRAME)
port->icount.frame++;
- if (status & (AT91_US_OVRE))
+ if (status & AT91_US_OVRE)
port->icount.overrun++;
- if (status & AT91_US_PARE)
+ status &= port->read_status_mask;
+
+ if (status & AT91_US_RXBRK)
+ flg = TTY_BREAK;
+ else if (status & AT91_US_PARE)
flg = TTY_PARITY;
else if (status & AT91_US_FRAME)
flg = TTY_FRAME;
- if (status & AT91_US_OVRE) {
- /*
- * overrun does *not* affect the character
- * we read from the FIFO
- */
- tty_insert_flip_char(tty, ch, flg);
- ch = 0;
- flg = TTY_OVERRUN;
- }
-#ifdef SUPPORT_SYSRQ
- port->sysrq = 0;
-#endif
}
if (uart_handle_sysrq_char(port, ch, regs))
goto ignore_char;
- tty_insert_flip_char(tty, ch, flg);
+ uart_insert_char(port, status, AT91_US_OVRE, ch, flg);
ignore_char:
- status = UART_GET_CSR(port) & port->read_status_mask;
+ status = UART_GET_CSR(port);
}
tty_flip_buffer_push(tty);
static irqreturn_t at91_interrupt(int irq, void *dev_id, struct pt_regs *regs)
{
struct uart_port *port = dev_id;
+ struct at91_uart_port *at91_port = (struct at91_uart_port *) port;
unsigned int status, pending, pass_counter = 0;
status = UART_GET_CSR(port);
- pending = status & port->read_status_mask;
- if (pending) {
- do {
- if (pending & AT91_US_RXRDY)
- at91_rx_chars(port, regs);
-
- /* Clear the relevent break bits */
- if (pending & AT91_US_RXBRK) {
- UART_PUT_CR(port, AT91_US_RSTSTA);
- port->icount.brk++;
- uart_handle_break(port);
- }
+ pending = status & UART_GET_IMR(port);
+ while (pending) {
+ /* Interrupt receive */
+ if (pending & AT91_US_RXRDY)
+ at91_rx_chars(port, regs);
+
+ // TODO: All reads to CSR will clear these interrupts!
+ if (pending & AT91_US_RIIC) port->icount.rng++;
+ if (pending & AT91_US_DSRIC) port->icount.dsr++;
+ if (pending & AT91_US_DCDIC)
+ uart_handle_dcd_change(port, !(status & AT91_US_DCD));
+ if (pending & AT91_US_CTSIC)
+ uart_handle_cts_change(port, !(status & AT91_US_CTS));
+ if (pending & (AT91_US_RIIC | AT91_US_DSRIC | AT91_US_DCDIC | AT91_US_CTSIC))
+ wake_up_interruptible(&port->info->delta_msr_wait);
+
+ /* Interrupt transmit */
+ if (pending & AT91_US_TXRDY)
+ at91_tx_chars(port);
+
+ if (pass_counter++ > AT91_ISR_PASS_LIMIT)
+ break;
- // TODO: All reads to CSR will clear these interrupts!
- if (pending & AT91_US_RIIC) port->icount.rng++;
- if (pending & AT91_US_DSRIC) port->icount.dsr++;
- if (pending & AT91_US_DCDIC)
- uart_handle_dcd_change(port, !(status & AT91_US_DCD));
- if (pending & AT91_US_CTSIC)
- uart_handle_cts_change(port, !(status & AT91_US_CTS));
- if (pending & (AT91_US_RIIC | AT91_US_DSRIC | AT91_US_DCDIC | AT91_US_CTSIC))
- wake_up_interruptible(&port->info->delta_msr_wait);
-
- if (pending & AT91_US_TXRDY)
- at91_tx_chars(port);
- if (pass_counter++ > AT91_ISR_PASS_LIMIT)
- break;
-
- status = UART_GET_CSR(port);
- pending = status & port->read_status_mask;
- } while (pending);
+ status = UART_GET_CSR(port);
+ pending = status & UART_GET_IMR(port);
}
return IRQ_HANDLED;
}
*/
static int at91_startup(struct uart_port *port)
{
+ struct at91_uart_port *at91_port = (struct at91_uart_port *) port;
int retval;
/*
/*
* Allocate the IRQ
*/
- retval = request_irq(port->irq, at91_interrupt, SA_SHIRQ, "at91_serial", port);
+ retval = request_irq(port->irq, at91_interrupt, IRQF_SHARED, "at91_serial", port);
if (retval) {
printk("at91_serial: at91_startup - Can't get irq\n");
return retval;
}
}
- port->read_status_mask = AT91_US_RXRDY | AT91_US_TXRDY | AT91_US_OVRE
- | AT91_US_FRAME | AT91_US_PARE | AT91_US_RXBRK;
/*
* Finally, enable the serial port
*/
UART_PUT_CR(port, AT91_US_RSTSTA | AT91_US_RSTRX);
UART_PUT_CR(port, AT91_US_TXEN | AT91_US_RXEN); /* enable xmit & rcvr */
- UART_PUT_IER(port, AT91_US_RXRDY); /* do receive only */
+
+ UART_PUT_IER(port, AT91_US_RXRDY); /* enable receive only */
+
return 0;
}
*/
static void at91_shutdown(struct uart_port *port)
{
+ struct at91_uart_port *at91_port = (struct at91_uart_port *) port;
+
/*
* Disable all interrupts, port and break condition.
*/
*/
static void at91_serial_pm(struct uart_port *port, unsigned int state, unsigned int oldstate)
{
+ struct at91_uart_port *at91_port = (struct at91_uart_port *) port;
+
switch (state) {
case 0:
/*
* Enable the peripheral clock for this serial port.
* This is called on uart_open() or a resume event.
*/
- at91_sys_write(AT91_PMC_PCER, 1 << port->irq);
+ clk_enable(at91_port->clk);
break;
case 3:
/*
* Disable the peripheral clock for this serial port.
* This is called on uart_close() or a suspend event.
*/
- if (port->irq != AT91_ID_SYS) /* is this a shared clock? */
- at91_sys_write(AT91_PMC_PCDR, 1 << port->irq);
+ clk_disable(at91_port->clk);
break;
default:
printk(KERN_ERR "at91_serial: unknown pm %d\n", state);
spin_lock_irqsave(&port->lock, flags);
- port->read_status_mask |= AT91_US_OVRE;
+ port->read_status_mask = AT91_US_OVRE;
if (termios->c_iflag & INPCK)
- port->read_status_mask |= AT91_US_FRAME | AT91_US_PARE;
+ port->read_status_mask |= (AT91_US_FRAME | AT91_US_PARE);
if (termios->c_iflag & (BRKINT | PARMRK))
port->read_status_mask |= AT91_US_RXBRK;
*/
static const char *at91_type(struct uart_port *port)
{
- return (port->type == PORT_AT91RM9200) ? "AT91_SERIAL" : NULL;
+ return (port->type == PORT_AT91) ? "AT91_SERIAL" : NULL;
}
/*
*/
static void at91_release_port(struct uart_port *port)
{
- release_mem_region(port->mapbase,
- (port->mapbase == AT91_VA_BASE_DBGU) ? 512 : SZ_16K);
+ struct platform_device *pdev = to_platform_device(port->dev);
+ int size = pdev->resource[0].end - pdev->resource[0].start + 1;
+
+ release_mem_region(port->mapbase, size);
+
+ if (port->flags & UPF_IOREMAP) {
+ iounmap(port->membase);
+ port->membase = NULL;
+ }
}
/*
*/
static int at91_request_port(struct uart_port *port)
{
- return request_mem_region(port->mapbase,
- (port->mapbase == AT91_VA_BASE_DBGU) ? 512 : SZ_16K,
- "at91_serial") != NULL ? 0 : -EBUSY;
+ struct platform_device *pdev = to_platform_device(port->dev);
+ int size = pdev->resource[0].end - pdev->resource[0].start + 1;
+ if (!request_mem_region(port->mapbase, size, "at91_serial"))
+ return -EBUSY;
+
+ if (port->flags & UPF_IOREMAP) {
+ port->membase = ioremap(port->mapbase, size);
+ if (port->membase == NULL) {
+ release_mem_region(port->mapbase, size);
+ return -ENOMEM;
+ }
+ }
+
+ return 0;
}
/*
static void at91_config_port(struct uart_port *port, int flags)
{
if (flags & UART_CONFIG_TYPE) {
- port->type = PORT_AT91RM9200;
+ port->type = PORT_AT91;
at91_request_port(port);
}
}
static int at91_verify_port(struct uart_port *port, struct serial_struct *ser)
{
int ret = 0;
- if (ser->type != PORT_UNKNOWN && ser->type != PORT_AT91RM9200)
+ if (ser->type != PORT_UNKNOWN && ser->type != PORT_AT91)
ret = -EINVAL;
if (port->irq != ser->irq)
ret = -EINVAL;
.type = at91_type,
.release_port = at91_release_port,
.request_port = at91_request_port,
- .config_port = at91_config_port,
- .verify_port = at91_verify_port,
+ .config_port = at91_config_port,
+ .verify_port = at91_verify_port,
.pm = at91_serial_pm,
};
-static struct uart_port at91_ports[AT91_NR_UART];
-
-void __init at91_init_ports(void)
+/*
+ * Configure the port from the platform device resource info.
+ */
+static void __devinit at91_init_port(struct at91_uart_port *at91_port, struct platform_device *pdev)
{
- static int first = 1;
- int i;
-
- if (!first)
- return;
- first = 0;
+ struct uart_port *port = &at91_port->uart;
+ struct at91_uart_data *data = pdev->dev.platform_data;
+
+ port->iotype = UPIO_MEM;
+ port->flags = UPF_BOOT_AUTOCONF;
+ port->ops = &at91_pops;
+ port->fifosize = 1;
+ port->line = pdev->id;
+ port->dev = &pdev->dev;
+
+ port->mapbase = pdev->resource[0].start;
+ port->irq = pdev->resource[1].start;
+
+ if (port->mapbase == AT91_VA_BASE_SYS + AT91_DBGU) /* Part of system perpherals - already mapped */
+ port->membase = (void __iomem *) port->mapbase;
+ else {
+ port->flags |= UPF_IOREMAP;
+ port->membase = NULL;
+ }
- for (i = 0; i < AT91_NR_UART; i++) {
- at91_ports[i].iotype = UPIO_MEM;
- at91_ports[i].flags = UPF_BOOT_AUTOCONF;
- at91_ports[i].uartclk = at91_master_clock;
- at91_ports[i].ops = &at91_pops;
- at91_ports[i].fifosize = 1;
- at91_ports[i].line = i;
- }
+ if (!at91_port->clk) { /* for console, the clock could already be configured */
+ at91_port->clk = clk_get(&pdev->dev, "usart");
+ clk_enable(at91_port->clk);
+ port->uartclk = clk_get_rate(at91_port->clk);
+ }
}
-void __init at91_register_uart_fns(struct at91rm9200_port_fns *fns)
+/*
+ * Register board-specific modem-control line handlers.
+ */
+void __init at91_register_uart_fns(struct at91_port_fns *fns)
{
if (fns->enable_ms)
at91_pops.enable_ms = fns->enable_ms;
at91_pops.set_wake = fns->set_wake;
}
-/*
- * Setup ports.
- */
-void __init at91_register_uart(int idx, int port)
-{
- if ((idx < 0) || (idx >= AT91_NR_UART)) {
- printk(KERN_ERR "%s: bad index number %d\n", __FUNCTION__, idx);
- return;
- }
-
- switch (port) {
- case 0:
- at91_ports[idx].membase = (void __iomem *) AT91_VA_BASE_US0;
- at91_ports[idx].mapbase = AT91_VA_BASE_US0;
- at91_ports[idx].irq = AT91_ID_US0;
- AT91_CfgPIO_USART0();
- break;
- case 1:
- at91_ports[idx].membase = (void __iomem *) AT91_VA_BASE_US1;
- at91_ports[idx].mapbase = AT91_VA_BASE_US1;
- at91_ports[idx].irq = AT91_ID_US1;
- AT91_CfgPIO_USART1();
- break;
- case 2:
- at91_ports[idx].membase = (void __iomem *) AT91_VA_BASE_US2;
- at91_ports[idx].mapbase = AT91_VA_BASE_US2;
- at91_ports[idx].irq = AT91_ID_US2;
- AT91_CfgPIO_USART2();
- break;
- case 3:
- at91_ports[idx].membase = (void __iomem *) AT91_VA_BASE_US3;
- at91_ports[idx].mapbase = AT91_VA_BASE_US3;
- at91_ports[idx].irq = AT91_ID_US3;
- AT91_CfgPIO_USART3();
- break;
- case 4:
- at91_ports[idx].membase = (void __iomem *) AT91_VA_BASE_DBGU;
- at91_ports[idx].mapbase = AT91_VA_BASE_DBGU;
- at91_ports[idx].irq = AT91_ID_SYS;
- AT91_CfgPIO_DBGU();
- break;
- default:
- printk(KERN_ERR "%s : bad port number %d\n", __FUNCTION__, port);
- }
-}
#ifdef CONFIG_SERIAL_AT91_CONSOLE
+static void at91_console_putchar(struct uart_port *port, int ch)
+{
+ while (!(UART_GET_CSR(port) & AT91_US_TXRDY))
+ barrier();
+ UART_PUT_CHAR(port, ch);
+}
/*
* Interrupts are disabled on entering
*/
static void at91_console_write(struct console *co, const char *s, u_int count)
{
- struct uart_port *port = at91_ports + co->index;
- unsigned int status, i, imr;
+ struct uart_port *port = &at91_ports[co->index].uart;
+ unsigned int status, imr;
/*
* First, save IMR and then disable interrupts
imr = UART_GET_IMR(port); /* get interrupt mask */
UART_PUT_IDR(port, AT91_US_RXRDY | AT91_US_TXRDY);
- /*
- * Now, do each character
- */
- for (i = 0; i < count; i++) {
- do {
- status = UART_GET_CSR(port);
- } while (!(status & AT91_US_TXRDY));
- UART_PUT_CHAR(port, s[i]);
- if (s[i] == '\n') {
- do {
- status = UART_GET_CSR(port);
- } while (!(status & AT91_US_TXRDY));
- UART_PUT_CHAR(port, '\r');
- }
- }
+ uart_console_write(port, s, count, at91_console_putchar);
/*
* Finally, wait for transmitter to become empty
static int __init at91_console_setup(struct console *co, char *options)
{
- struct uart_port *port;
+ struct uart_port *port = &at91_ports[co->index].uart;
int baud = 115200;
int bits = 8;
int parity = 'n';
int flow = 'n';
- /*
- * Check whether an invalid uart number has been specified, and
- * if so, search for the first available port that does have
- * console support.
- */
- port = uart_get_console(at91_ports, AT91_NR_UART, co);
+ if (port->membase == 0) /* Port not initialized yet - delay setup */
+ return -ENODEV;
- /*
- * Enable the serial console, in-case bootloader did not do it.
- */
- at91_sys_write(AT91_PMC_PCER, 1 << port->irq); /* enable clock */
UART_PUT_IDR(port, -1); /* disable interrupts */
UART_PUT_CR(port, AT91_US_RSTSTA | AT91_US_RSTRX);
UART_PUT_CR(port, AT91_US_TXEN | AT91_US_RXEN);
#define AT91_CONSOLE_DEVICE &at91_console
-static int __init at91_console_init(void)
+/*
+ * Early console initialization (before VM subsystem initialized).
+ */
+static int __init at91_console_init(void)
{
- at91_init_ports();
+ if (at91_default_console_device) {
+ add_preferred_console(AT91_DEVICENAME, at91_default_console_device->id, NULL);
+ at91_init_port(&(at91_ports[at91_default_console_device->id]), at91_default_console_device);
+ register_console(&at91_console);
+ }
- at91_console.index = at91_console_port;
- register_console(&at91_console);
return 0;
}
console_initcall(at91_console_init);
+/*
+ * Late console initialization.
+ */
+static int __init at91_late_console_init(void)
+{
+ if (at91_default_console_device && !(at91_console.flags & CON_ENABLED))
+ register_console(&at91_console);
+
+ return 0;
+}
+core_initcall(at91_late_console_init);
+
#else
#define AT91_CONSOLE_DEVICE NULL
#endif
static struct uart_driver at91_uart = {
.owner = THIS_MODULE,
- .driver_name = AT91_DEVICENAME,
+ .driver_name = "at91_serial",
.dev_name = AT91_DEVICENAME,
- .devfs_name = AT91_DEVICENAME,
.major = SERIAL_AT91_MAJOR,
.minor = MINOR_START,
.nr = AT91_NR_UART,
.cons = AT91_CONSOLE_DEVICE,
};
-static int __init at91_serial_init(void)
+#ifdef CONFIG_PM
+static int at91_serial_suspend(struct platform_device *pdev, pm_message_t state)
{
- int ret, i;
+ struct uart_port *port = platform_get_drvdata(pdev);
+ struct at91_uart_port *at91_port = (struct at91_uart_port *) port;
+
+ if (device_may_wakeup(&pdev->dev) && !at91_suspend_entering_slow_clock())
+ enable_irq_wake(port->irq);
+ else {
+ disable_irq_wake(port->irq);
+ uart_suspend_port(&at91_uart, port);
+ at91_port->suspended = 1;
+ }
- at91_init_ports();
+ return 0;
+}
- ret = uart_register_driver(&at91_uart);
- if (ret)
- return ret;
+static int at91_serial_resume(struct platform_device *pdev)
+{
+ struct uart_port *port = platform_get_drvdata(pdev);
+ struct at91_uart_port *at91_port = (struct at91_uart_port *) port;
- for (i = 0; i < AT91_NR_UART; i++) {
- if (at91_serial_map[i] >= 0)
- uart_add_one_port(&at91_uart, &at91_ports[i]);
+ if (at91_port->suspended) {
+ uart_resume_port(&at91_uart, port);
+ at91_port->suspended = 0;
}
return 0;
}
+#else
+#define at91_serial_suspend NULL
+#define at91_serial_resume NULL
+#endif
+
+static int __devinit at91_serial_probe(struct platform_device *pdev)
+{
+ struct at91_uart_port *port;
+ int ret;
+
+ port = &at91_ports[pdev->id];
+ at91_init_port(port, pdev);
+
+ ret = uart_add_one_port(&at91_uart, &port->uart);
+ if (!ret) {
+ device_init_wakeup(&pdev->dev, 1);
+ platform_set_drvdata(pdev, port);
+ }
+
+ return ret;
+}
-static void __exit at91_serial_exit(void)
+static int __devexit at91_serial_remove(struct platform_device *pdev)
{
- int i;
+ struct uart_port *port = platform_get_drvdata(pdev);
+ struct at91_uart_port *at91_port = (struct at91_uart_port *) port;
+ int ret = 0;
+
+ clk_disable(at91_port->clk);
+ clk_put(at91_port->clk);
+
+ device_init_wakeup(&pdev->dev, 0);
+ platform_set_drvdata(pdev, NULL);
- for (i = 0; i < AT91_NR_UART; i++) {
- if (at91_serial_map[i] >= 0)
- uart_remove_one_port(&at91_uart, &at91_ports[i]);
- }
+ if (port) {
+ ret = uart_remove_one_port(&at91_uart, port);
+ kfree(port);
+ }
+
+ return ret;
+}
+static struct platform_driver at91_serial_driver = {
+ .probe = at91_serial_probe,
+ .remove = __devexit_p(at91_serial_remove),
+ .suspend = at91_serial_suspend,
+ .resume = at91_serial_resume,
+ .driver = {
+ .name = "at91_usart",
+ .owner = THIS_MODULE,
+ },
+};
+
+static int __init at91_serial_init(void)
+{
+ int ret;
+
+ ret = uart_register_driver(&at91_uart);
+ if (ret)
+ return ret;
+
+ ret = platform_driver_register(&at91_serial_driver);
+ if (ret)
+ uart_unregister_driver(&at91_uart);
+
+ return ret;
+}
+
+static void __exit at91_serial_exit(void)
+{
+ platform_driver_unregister(&at91_serial_driver);
uart_unregister_driver(&at91_uart);
}