#include <linux/libata.h>
#define DRV_NAME "sata_vsc"
-#define DRV_VERSION "1.1"
-
-/* Interrupt register offsets (from chip base address) */
-#define VSC_SATA_INT_STAT_OFFSET 0x00
-#define VSC_SATA_INT_MASK_OFFSET 0x04
-
-/* Taskfile registers offsets */
-#define VSC_SATA_TF_CMD_OFFSET 0x00
-#define VSC_SATA_TF_DATA_OFFSET 0x00
-#define VSC_SATA_TF_ERROR_OFFSET 0x04
-#define VSC_SATA_TF_FEATURE_OFFSET 0x06
-#define VSC_SATA_TF_NSECT_OFFSET 0x08
-#define VSC_SATA_TF_LBAL_OFFSET 0x0c
-#define VSC_SATA_TF_LBAM_OFFSET 0x10
-#define VSC_SATA_TF_LBAH_OFFSET 0x14
-#define VSC_SATA_TF_DEVICE_OFFSET 0x18
-#define VSC_SATA_TF_STATUS_OFFSET 0x1c
-#define VSC_SATA_TF_COMMAND_OFFSET 0x1d
-#define VSC_SATA_TF_ALTSTATUS_OFFSET 0x28
-#define VSC_SATA_TF_CTL_OFFSET 0x29
-
-/* DMA base */
-#define VSC_SATA_UP_DESCRIPTOR_OFFSET 0x64
-#define VSC_SATA_UP_DATA_BUFFER_OFFSET 0x6C
-#define VSC_SATA_DMA_CMD_OFFSET 0x70
-
-/* SCRs base */
-#define VSC_SATA_SCR_STATUS_OFFSET 0x100
-#define VSC_SATA_SCR_ERROR_OFFSET 0x104
-#define VSC_SATA_SCR_CONTROL_OFFSET 0x108
-
-/* Port stride */
-#define VSC_SATA_PORT_OFFSET 0x200
-
-/* Error interrupt status bit offsets */
-#define VSC_SATA_INT_ERROR_E_OFFSET 2
-#define VSC_SATA_INT_ERROR_P_OFFSET 4
-#define VSC_SATA_INT_ERROR_T_OFFSET 5
-#define VSC_SATA_INT_ERROR_M_OFFSET 1
+#define DRV_VERSION "1.2"
+
+enum {
+ /* Interrupt register offsets (from chip base address) */
+ VSC_SATA_INT_STAT_OFFSET = 0x00,
+ VSC_SATA_INT_MASK_OFFSET = 0x04,
+
+ /* Taskfile registers offsets */
+ VSC_SATA_TF_CMD_OFFSET = 0x00,
+ VSC_SATA_TF_DATA_OFFSET = 0x00,
+ VSC_SATA_TF_ERROR_OFFSET = 0x04,
+ VSC_SATA_TF_FEATURE_OFFSET = 0x06,
+ VSC_SATA_TF_NSECT_OFFSET = 0x08,
+ VSC_SATA_TF_LBAL_OFFSET = 0x0c,
+ VSC_SATA_TF_LBAM_OFFSET = 0x10,
+ VSC_SATA_TF_LBAH_OFFSET = 0x14,
+ VSC_SATA_TF_DEVICE_OFFSET = 0x18,
+ VSC_SATA_TF_STATUS_OFFSET = 0x1c,
+ VSC_SATA_TF_COMMAND_OFFSET = 0x1d,
+ VSC_SATA_TF_ALTSTATUS_OFFSET = 0x28,
+ VSC_SATA_TF_CTL_OFFSET = 0x29,
+
+ /* DMA base */
+ VSC_SATA_UP_DESCRIPTOR_OFFSET = 0x64,
+ VSC_SATA_UP_DATA_BUFFER_OFFSET = 0x6C,
+ VSC_SATA_DMA_CMD_OFFSET = 0x70,
+
+ /* SCRs base */
+ VSC_SATA_SCR_STATUS_OFFSET = 0x100,
+ VSC_SATA_SCR_ERROR_OFFSET = 0x104,
+ VSC_SATA_SCR_CONTROL_OFFSET = 0x108,
+
+ /* Port stride */
+ VSC_SATA_PORT_OFFSET = 0x200,
+
+ /* Error interrupt status bit offsets */
+ VSC_SATA_INT_ERROR_CRC = 0x40,
+ VSC_SATA_INT_ERROR_T = 0x20,
+ VSC_SATA_INT_ERROR_P = 0x10,
+ VSC_SATA_INT_ERROR_R = 0x8,
+ VSC_SATA_INT_ERROR_E = 0x4,
+ VSC_SATA_INT_ERROR_M = 0x2,
+ VSC_SATA_INT_PHY_CHANGE = 0x1,
+ VSC_SATA_INT_ERROR = (VSC_SATA_INT_ERROR_CRC | VSC_SATA_INT_ERROR_T | \
+ VSC_SATA_INT_ERROR_P | VSC_SATA_INT_ERROR_R | \
+ VSC_SATA_INT_ERROR_E | VSC_SATA_INT_ERROR_M | \
+ VSC_SATA_INT_PHY_CHANGE),
+};
+
+
#define is_vsc_sata_int_err(port_idx, int_status) \
- (int_status & ((1 << (VSC_SATA_INT_ERROR_E_OFFSET + (8 * port_idx))) | \
- (1 << (VSC_SATA_INT_ERROR_P_OFFSET + (8 * port_idx))) | \
- (1 << (VSC_SATA_INT_ERROR_T_OFFSET + (8 * port_idx))) | \
- (1 << (VSC_SATA_INT_ERROR_M_OFFSET + (8 * port_idx))) \
- )\
- )
+ (int_status & (VSC_SATA_INT_ERROR << (8 * port_idx)))
static u32 vsc_sata_scr_read (struct ata_port *ap, unsigned int sc_reg)
handled++;
}
- if (ap && !(ap->flags &
- (ATA_FLAG_PORT_DISABLED|ATA_FLAG_NOINTR))) {
+ if (ap && !(ap->flags & ATA_FLAG_DISABLED)) {
struct ata_queued_cmd *qc;
qc = ata_qc_from_tag(ap, ap->active_tag);
- if (qc && (!(qc->tf.ctl & ATA_NIEN))) {
+ if (qc && (!(qc->tf.flags & ATA_TFLAG_POLLING)))
handled += ata_host_intr(ap, qc);
- } else {
- printk(KERN_DEBUG "%s: ignoring interrupt(s)\n", __FUNCTION__);
+ else if (is_vsc_sata_int_err(i, int_status)) {
+ /*
+ * On some chips (i.e. Intel 31244), an error
+ * interrupt will sneak in at initialization
+ * time (phy state changes). Clearing the SCR
+ * error register is not required, but it prevents
+ * the phy state change interrupts from recurring
+ * later.
+ */
+ u32 err_status;
+ err_status = vsc_sata_scr_read(ap, SCR_ERROR);
+ printk(KERN_DEBUG "%s: clearing interrupt, "
+ "status %x; sata err status %x\n",
+ __FUNCTION__,
+ int_status, err_status);
+ vsc_sata_scr_write(ap, SCR_ERROR, err_status);
+ /* Clear interrupt status */
ata_chk_status(ap);
handled++;
}
-
}
}
}
.name = DRV_NAME,
.ioctl = ata_scsi_ioctl,
.queuecommand = ata_scsi_queuecmd,
- .eh_timed_out = ata_scsi_timed_out,
- .eh_strategy_handler = ata_scsi_error,
.can_queue = ATA_DEF_QUEUE,
.this_id = ATA_SHT_THIS_ID,
.sg_tablesize = LIBATA_MAX_PRD,
.proc_name = DRV_NAME,
.dma_boundary = ATA_DMA_BOUNDARY,
.slave_configure = ata_scsi_slave_config,
+ .slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
};
.exec_command = ata_exec_command,
.check_status = ata_check_status,
.dev_select = ata_std_dev_select,
- .phy_reset = sata_phy_reset,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = ata_bmdma_start,
.bmdma_stop = ata_bmdma_stop,
.bmdma_status = ata_bmdma_status,
.qc_prep = ata_qc_prep,
.qc_issue = ata_qc_issue_prot,
- .eng_timeout = ata_eng_timeout,
+ .data_xfer = ata_pio_data_xfer,
+ .freeze = ata_bmdma_freeze,
+ .thaw = ata_bmdma_thaw,
+ .error_handler = ata_bmdma_error_handler,
+ .post_internal_cmd = ata_bmdma_post_internal_cmd,
.irq_handler = vsc_sata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
.scr_read = vsc_sata_scr_read,
probe_ent->sht = &vsc_sata_sht;
probe_ent->host_flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
- ATA_FLAG_MMIO | ATA_FLAG_SATA_RESET;
+ ATA_FLAG_MMIO;
probe_ent->port_ops = &vsc_sata_ops;
probe_ent->n_ports = 4;
probe_ent->irq = pdev->irq;
projects / linux-2.6 / blobdiff