#include <linux/init.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
-#include "scsi.h"
+#include <linux/device.h>
#include <scsi/scsi_host.h>
#include <linux/libata.h>
#include <asm/io.h>
static u32 svia_scr_read (struct ata_port *ap, unsigned int sc_reg);
static void svia_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val);
-static struct pci_device_id svia_pci_tbl[] = {
+static const struct pci_device_id svia_pci_tbl[] = {
{ 0x1106, 0x3149, PCI_ANY_ID, PCI_ANY_ID, 0, 0, vt6420 },
{ 0x1106, 0x3249, PCI_ANY_ID, PCI_ANY_ID, 0, 0, vt6421 },
.remove = ata_pci_remove_one,
};
-static Scsi_Host_Template svia_sht = {
+static struct scsi_host_template svia_sht = {
.module = THIS_MODULE,
.name = DRV_NAME,
.ioctl = ata_scsi_ioctl,
.dma_boundary = ATA_DMA_BOUNDARY,
.slave_configure = ata_scsi_slave_config,
.bios_param = ata_std_bios_param,
- .ordered_flush = 1,
};
-static struct ata_port_operations svia_sata_ops = {
+static const struct ata_port_operations svia_sata_ops = {
.port_disable = ata_port_disable,
.tf_load = ata_tf_load,
u8 tmp8;
pci_read_config_byte(pdev, PCI_INTERRUPT_LINE, &tmp8);
- printk(KERN_INFO DRV_NAME "(%s): routed to hard irq line %d\n",
- pci_name(pdev),
+ dev_printk(KERN_INFO, &pdev->dev, "routed to hard irq line %d\n",
(int) (tmp8 & 0xf0) == 0xf0 ? 0 : tmp8 & 0x0f);
/* make sure SATA channels are enabled */
pci_read_config_byte(pdev, SATA_CHAN_ENAB, &tmp8);
if ((tmp8 & ALL_PORTS) != ALL_PORTS) {
- printk(KERN_DEBUG DRV_NAME "(%s): enabling SATA channels (0x%x)\n",
- pci_name(pdev), (int) tmp8);
+ dev_printk(KERN_DEBUG, &pdev->dev,
+ "enabling SATA channels (0x%x)\n",
+ (int) tmp8);
tmp8 |= ALL_PORTS;
pci_write_config_byte(pdev, SATA_CHAN_ENAB, tmp8);
}
/* make sure interrupts for each channel sent to us */
pci_read_config_byte(pdev, SATA_INT_GATE, &tmp8);
if ((tmp8 & ALL_PORTS) != ALL_PORTS) {
- printk(KERN_DEBUG DRV_NAME "(%s): enabling SATA channel interrupts (0x%x)\n",
- pci_name(pdev), (int) tmp8);
+ dev_printk(KERN_DEBUG, &pdev->dev,
+ "enabling SATA channel interrupts (0x%x)\n",
+ (int) tmp8);
tmp8 |= ALL_PORTS;
pci_write_config_byte(pdev, SATA_INT_GATE, tmp8);
}
/* make sure native mode is enabled */
pci_read_config_byte(pdev, SATA_NATIVE_MODE, &tmp8);
if ((tmp8 & NATIVE_MODE_ALL) != NATIVE_MODE_ALL) {
- printk(KERN_DEBUG DRV_NAME "(%s): enabling SATA channel native mode (0x%x)\n",
- pci_name(pdev), (int) tmp8);
+ dev_printk(KERN_DEBUG, &pdev->dev,
+ "enabling SATA channel native mode (0x%x)\n",
+ (int) tmp8);
tmp8 |= NATIVE_MODE_ALL;
pci_write_config_byte(pdev, SATA_NATIVE_MODE, tmp8);
}
u8 tmp8;
if (!printed_version++)
- printk(KERN_DEBUG DRV_NAME " version " DRV_VERSION "\n");
+ dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n");
rc = pci_enable_device(pdev);
if (rc)
if (board_id == vt6420) {
pci_read_config_byte(pdev, SATA_PATA_SHARING, &tmp8);
if (tmp8 & SATA_2DEV) {
- printk(KERN_ERR DRV_NAME "(%s): SATA master/slave not supported (0x%x)\n",
- pci_name(pdev), (int) tmp8);
+ dev_printk(KERN_ERR, &pdev->dev,
+ "SATA master/slave not supported (0x%x)\n",
+ (int) tmp8);
rc = -EIO;
goto err_out_regions;
}
for (i = 0; i < ARRAY_SIZE(svia_bar_sizes); i++)
if ((pci_resource_start(pdev, i) == 0) ||
(pci_resource_len(pdev, i) < bar_sizes[i])) {
- printk(KERN_ERR DRV_NAME "(%s): invalid PCI BAR %u (sz 0x%lx, val 0x%lx)\n",
- pci_name(pdev), i,
- pci_resource_start(pdev, i),
- pci_resource_len(pdev, i));
+ dev_printk(KERN_ERR, &pdev->dev,
+ "invalid PCI BAR %u (sz 0x%lx, val 0x%lx)\n",
+ i,
+ pci_resource_start(pdev, i),
+ pci_resource_len(pdev, i));
rc = -ENODEV;
goto err_out_regions;
}
probe_ent = vt6421_init_probe_ent(pdev);
if (!probe_ent) {
- printk(KERN_ERR DRV_NAME "(%s): out of memory\n",
- pci_name(pdev));
+ dev_printk(KERN_ERR, &pdev->dev, "out of memory\n");
rc = -ENOMEM;
goto err_out_regions;
}