#include <linux/libata.h>
#define DRV_NAME "sata_sil"
-#define DRV_VERSION "0.9"
+#define DRV_VERSION "1.0"
enum {
/*
*/
SIL_FLAG_RERR_ON_DMA_ACT = (1 << 29),
SIL_FLAG_MOD15WRITE = (1 << 30),
+
SIL_DFL_HOST_FLAGS = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
- ATA_FLAG_MMIO,
+ ATA_FLAG_MMIO | ATA_FLAG_HRST_TO_RESUME,
/*
* Controller IDs
/* BMDMA/BMDMA2 */
SIL_INTR_STEERING = (1 << 1),
+ SIL_DMA_ENABLE = (1 << 0), /* DMA run switch */
+ SIL_DMA_RDWR = (1 << 3), /* DMA Rd-Wr */
+ SIL_DMA_SATA_IRQ = (1 << 4), /* OR of all SATA IRQs */
+ SIL_DMA_ACTIVE = (1 << 16), /* DMA running */
+ SIL_DMA_ERROR = (1 << 17), /* PCI bus error */
+ SIL_DMA_COMPLETE = (1 << 18), /* cmd complete / IRQ pending */
+ SIL_DMA_N_SATA_IRQ = (1 << 6), /* SATA_IRQ for the next channel */
+ SIL_DMA_N_ACTIVE = (1 << 24), /* ACTIVE for the next channel */
+ SIL_DMA_N_ERROR = (1 << 25), /* ERROR for the next channel */
+ SIL_DMA_N_COMPLETE = (1 << 26), /* COMPLETE for the next channel */
+
+ /* SIEN */
+ SIL_SIEN_N = (1 << 16), /* triggered by SError.N */
+
/*
* Others
*/
static u32 sil_scr_read (struct ata_port *ap, unsigned int sc_reg);
static void sil_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val);
static void sil_post_set_mode (struct ata_port *ap);
+static irqreturn_t sil_interrupt(int irq, void *dev_instance,
+ struct pt_regs *regs);
+static void sil_freeze(struct ata_port *ap);
+static void sil_thaw(struct ata_port *ap);
static const struct pci_device_id sil_pci_tbl[] = {
.name = DRV_NAME,
.ioctl = ata_scsi_ioctl,
.queuecommand = ata_scsi_queuecmd,
- .eh_strategy_handler = ata_scsi_error,
.can_queue = ATA_DEF_QUEUE,
.this_id = ATA_SHT_THIS_ID,
.sg_tablesize = LIBATA_MAX_PRD,
.proc_name = DRV_NAME,
.dma_boundary = ATA_DMA_BOUNDARY,
.slave_configure = ata_scsi_slave_config,
+ .slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
};
.check_status = ata_check_status,
.exec_command = ata_exec_command,
.dev_select = ata_std_dev_select,
- .probe_reset = ata_std_probe_reset,
.post_set_mode = sil_post_set_mode,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = ata_bmdma_start,
.bmdma_status = ata_bmdma_status,
.qc_prep = ata_qc_prep,
.qc_issue = ata_qc_issue_prot,
- .eng_timeout = ata_eng_timeout,
- .irq_handler = ata_interrupt,
+ .data_xfer = ata_mmio_data_xfer,
+ .freeze = sil_freeze,
+ .thaw = sil_thaw,
+ .error_handler = ata_bmdma_error_handler,
+ .post_internal_cmd = ata_bmdma_post_internal_cmd,
+ .irq_handler = sil_interrupt,
.irq_clear = ata_bmdma_irq_clear,
.scr_read = sil_scr_read,
.scr_write = sil_scr_write,
unsigned long tf; /* ATA taskfile register block */
unsigned long ctl; /* ATA control/altstatus register block */
unsigned long bmdma; /* DMA register block */
+ unsigned long bmdma2; /* DMA register block #2 */
unsigned long fifo_cfg; /* FIFO Valid Byte Count and Control */
unsigned long scr; /* SATA control register block */
unsigned long sien; /* SATA Interrupt Enable register */
unsigned long sfis_cfg; /* SATA FIS reception config register */
} sil_port[] = {
/* port 0 ... */
- { 0x80, 0x8A, 0x00, 0x40, 0x100, 0x148, 0xb4, 0x14c },
- { 0xC0, 0xCA, 0x08, 0x44, 0x180, 0x1c8, 0xf4, 0x1cc },
- { 0x280, 0x28A, 0x200, 0x240, 0x300, 0x348, 0x2b4, 0x34c },
- { 0x2C0, 0x2CA, 0x208, 0x244, 0x380, 0x3c8, 0x2f4, 0x3cc },
+ { 0x80, 0x8A, 0x00, 0x10, 0x40, 0x100, 0x148, 0xb4, 0x14c },
+ { 0xC0, 0xCA, 0x08, 0x18, 0x44, 0x180, 0x1c8, 0xf4, 0x1cc },
+ { 0x280, 0x28A, 0x200, 0x210, 0x240, 0x300, 0x348, 0x2b4, 0x34c },
+ { 0x2C0, 0x2CA, 0x208, 0x218, 0x244, 0x380, 0x3c8, 0x2f4, 0x3cc },
/* ... port 3 */
};
for (i = 0; i < 2; i++) {
dev = &ap->device[i];
- if (!ata_dev_present(dev))
+ if (!ata_dev_enabled(dev))
dev_mode[i] = 0; /* PIO0/1/2 */
else if (dev->flags & ATA_DFLAG_PIO)
dev_mode[i] = 1; /* PIO3/4 */
writel(val, mmio);
}
+static void sil_host_intr(struct ata_port *ap, u32 bmdma2)
+{
+ struct ata_queued_cmd *qc = ata_qc_from_tag(ap, ap->active_tag);
+ u8 status;
+
+ if (unlikely(bmdma2 & SIL_DMA_SATA_IRQ)) {
+ ata_ehi_hotplugged(&ap->eh_info);
+ goto freeze;
+ }
+
+ if (unlikely(!qc || qc->tf.ctl & ATA_NIEN))
+ goto freeze;
+
+ /* Check whether we are expecting interrupt in this state */
+ switch (ap->hsm_task_state) {
+ case HSM_ST_FIRST:
+ /* Some pre-ATAPI-4 devices assert INTRQ
+ * at this state when ready to receive CDB.
+ */
+
+ /* Check the ATA_DFLAG_CDB_INTR flag is enough here.
+ * The flag was turned on only for atapi devices.
+ * No need to check is_atapi_taskfile(&qc->tf) again.
+ */
+ if (!(qc->dev->flags & ATA_DFLAG_CDB_INTR))
+ goto err_hsm;
+ break;
+ case HSM_ST_LAST:
+ if (qc->tf.protocol == ATA_PROT_DMA ||
+ qc->tf.protocol == ATA_PROT_ATAPI_DMA) {
+ /* clear DMA-Start bit */
+ ap->ops->bmdma_stop(qc);
+
+ if (bmdma2 & SIL_DMA_ERROR) {
+ qc->err_mask |= AC_ERR_HOST_BUS;
+ ap->hsm_task_state = HSM_ST_ERR;
+ }
+ }
+ break;
+ case HSM_ST:
+ break;
+ default:
+ goto err_hsm;
+ }
+
+ /* check main status, clearing INTRQ */
+ status = ata_chk_status(ap);
+ if (unlikely(status & ATA_BUSY))
+ goto err_hsm;
+
+ /* ack bmdma irq events */
+ ata_bmdma_irq_clear(ap);
+
+ /* kick HSM in the ass */
+ ata_hsm_move(ap, qc, status, 0);
+
+ return;
+
+ err_hsm:
+ qc->err_mask |= AC_ERR_HSM;
+ freeze:
+ ata_port_freeze(ap);
+}
+
+static irqreturn_t sil_interrupt(int irq, void *dev_instance,
+ struct pt_regs *regs)
+{
+ struct ata_host_set *host_set = dev_instance;
+ void __iomem *mmio_base = host_set->mmio_base;
+ int handled = 0;
+ int i;
+
+ spin_lock(&host_set->lock);
+
+ for (i = 0; i < host_set->n_ports; i++) {
+ struct ata_port *ap = host_set->ports[i];
+ u32 bmdma2 = readl(mmio_base + sil_port[ap->port_no].bmdma2);
+
+ if (unlikely(!ap || ap->flags & ATA_FLAG_DISABLED))
+ continue;
+
+ if (!(bmdma2 & (SIL_DMA_COMPLETE | SIL_DMA_SATA_IRQ)))
+ continue;
+
+ sil_host_intr(ap, bmdma2);
+ handled = 1;
+ }
+
+ spin_unlock(&host_set->lock);
+
+ return IRQ_RETVAL(handled);
+}
+
+static void sil_freeze(struct ata_port *ap)
+{
+ void __iomem *mmio_base = ap->host_set->mmio_base;
+ u32 tmp;
+
+ /* global IRQ mask doesn't block SATA IRQ, turn off explicitly */
+ writel(0, mmio_base + sil_port[ap->port_no].sien);
+
+ /* plug IRQ */
+ tmp = readl(mmio_base + SIL_SYSCFG);
+ tmp |= SIL_MASK_IDE0_INT << ap->port_no;
+ writel(tmp, mmio_base + SIL_SYSCFG);
+ readl(mmio_base + SIL_SYSCFG); /* flush */
+}
+
+static void sil_thaw(struct ata_port *ap)
+{
+ void __iomem *mmio_base = ap->host_set->mmio_base;
+ u32 tmp;
+
+ /* clear IRQ */
+ ata_chk_status(ap);
+ ata_bmdma_irq_clear(ap);
+
+ /* turn on SATA IRQ */
+ writel(SIL_SIEN_N, mmio_base + sil_port[ap->port_no].sien);
+
+ /* turn on IRQ */
+ tmp = readl(mmio_base + SIL_SYSCFG);
+ tmp &= ~(SIL_MASK_IDE0_INT << ap->port_no);
+ writel(tmp, mmio_base + SIL_SYSCFG);
+}
+
/**
* sil_dev_config - Apply device/host-specific errata fixups
* @ap: Port containing device to be examined
if (slow_down ||
((ap->flags & SIL_FLAG_MOD15WRITE) &&
(quirks & SIL_QUIRK_MOD15WRITE))) {
- printk(KERN_INFO "ata%u(%u): applying Seagate errata fix (mod15write workaround)\n",
- ap->id, dev->devno);
+ ata_dev_printk(dev, KERN_INFO, "applying Seagate errata fix "
+ "(mod15write workaround)\n");
dev->max_sectors = 15;
return;
}
/* limit to udma5 */
if (quirks & SIL_QUIRK_UDMA5MAX) {
- printk(KERN_INFO "ata%u(%u): applying Maxtor errata fix %s\n",
- ap->id, dev->devno, model_num);
- ap->udma_mask &= ATA_UDMA5;
+ ata_dev_printk(dev, KERN_INFO,
+ "applying Maxtor errata fix %s\n", model_num);
+ dev->udma_mask &= ATA_UDMA5;
return;
}
}
int rc;
unsigned int i;
int pci_dev_busy = 0;
- u32 tmp, irq_mask;
+ u32 tmp;
u8 cls;
if (!printed_version++)
dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n");
- /*
- * If this driver happens to only be useful on Apple's K2, then
- * we should check that here as it has a normal Serverworks ID
- */
rc = pci_enable_device(pdev);
if (rc)
return rc;
}
if (ent->driver_data == sil_3114) {
- irq_mask = SIL_MASK_4PORT;
-
/* flip the magic "make 4 ports work" bit */
tmp = readl(mmio_base + sil_port[2].bmdma);
if ((tmp & SIL_INTR_STEERING) == 0)
writel(tmp | SIL_INTR_STEERING,
mmio_base + sil_port[2].bmdma);
-
- } else {
- irq_mask = SIL_MASK_2PORT;
- }
-
- /* make sure IDE0/1/2/3 interrupts are not masked */
- tmp = readl(mmio_base + SIL_SYSCFG);
- if (tmp & irq_mask) {
- tmp &= ~irq_mask;
- writel(tmp, mmio_base + SIL_SYSCFG);
- readl(mmio_base + SIL_SYSCFG); /* flush */
}
- /* mask all SATA phy-related interrupts */
- /* TODO: unmask bit 6 (SError N bit) for hotplug */
- for (i = 0; i < probe_ent->n_ports; i++)
- writel(0, mmio_base + sil_port[i].sien);
-
pci_set_master(pdev);
/* FIXME: check ata_device_add return value */