#include <linux/module.h>
-#include <linux/version.h>
#include <linux/types.h>
#include <linux/string.h>
#include <linux/errno.h>
#include <asm/sn/io.h>
#endif
-#if LINUX_VERSION_CODE < 0x020600
-#error "Kernels older than 2.6.0 are no longer supported"
-#endif
-
/*
* Compile time Options:
#define CMD_CDBLEN(Cmnd) Cmnd->cmd_len
#define CMD_CDBP(Cmnd) Cmnd->cmnd
#define CMD_SNSP(Cmnd) Cmnd->sense_buffer
-#define CMD_SNSLEN(Cmnd) sizeof(Cmnd->sense_buffer)
+#define CMD_SNSLEN(Cmnd) SCSI_SENSE_BUFFERSIZE
#define CMD_RESULT(Cmnd) Cmnd->result
#define CMD_HANDLE(Cmnd) Cmnd->host_scribble
#define CMD_REQUEST(Cmnd) Cmnd->request->cmd
nv->bus[bus].config_2.req_ack_active_negation = 1;
nv->bus[bus].config_2.data_line_active_negation = 1;
nv->bus[bus].selection_timeout = 250;
- nv->bus[bus].max_queue_depth = 256;
+ nv->bus[bus].max_queue_depth = 32;
if (IS_ISP1040(ha)) {
nv->bus[bus].bus_reset_delay = 3;
status = qla1280_mailbox_command(ha, 0x0f, mb);
/* Save Tag queuing enable flag. */
- flag = (BIT_0 << target) & mb[0];
+ flag = (BIT_0 << target);
if (nv->bus[bus].target[target].parameter.tag_queuing)
ha->bus_settings[bus].qtag_enables |= flag;
/* Load SCSI command packet. */
pkt->cdb_len = cpu_to_le16(CMD_CDBLEN(cmd));
- memcpy(pkt->scsi_cdb, &(CMD_CDBP(cmd)), CMD_CDBLEN(cmd));
+ memcpy(pkt->scsi_cdb, CMD_CDBP(cmd), CMD_CDBLEN(cmd));
/* dprintk(1, "Build packet for command[0]=0x%x\n",pkt->scsi_cdb[0]); */
/* Set transfer direction. */
int cnt;
int req_cnt;
int seg_cnt;
- dma_addr_t dma_handle;
u8 dir;
ENTER("qla1280_32bit_start_scsi");
cmd->cmnd[0]);
/* Calculate number of entries and segments required. */
+ req_cnt = 1;
seg_cnt = scsi_dma_map(cmd);
if (seg_cnt) {
/*
/* Load SCSI command packet. */
pkt->cdb_len = cpu_to_le16(CMD_CDBLEN(cmd));
- memcpy(pkt->scsi_cdb, &(CMD_CDBP(cmd)), CMD_CDBLEN(cmd));
+ memcpy(pkt->scsi_cdb, CMD_CDBP(cmd), CMD_CDBLEN(cmd));
/*dprintk(1, "Build packet for command[0]=0x%x\n",pkt->scsi_cdb[0]); */
/* Set transfer direction. */
} else
sense_sz = 0;
memset(cmd->sense_buffer + sense_sz, 0,
- sizeof(cmd->sense_buffer) - sense_sz);
+ SCSI_SENSE_BUFFERSIZE - sense_sz);
dprintk(2, "qla1280_status_entry: Check "
"condition Sense data, b %i, t %i, "
.sg_tablesize = SG_ALL,
.cmd_per_lun = 1,
.use_clustering = ENABLE_CLUSTERING,
- .use_sg_chaining = ENABLE_SG_CHAINING,
};