config SCSI_ISCSI_ATTRS
tristate "iSCSI Transport Attributes"
- depends on SCSI
+ depends on SCSI && NET
help
If you wish to export transport-specific information about
each attached iSCSI device to sysfs, say Y.
Otherwise, say N.
+config SCSI_SAS_ATTRS
+ tristate "SAS Transport Attributes"
+ depends on SCSI
+ help
+ If you wish to export transport-specific information about
+ each attached SAS device to sysfs, say Y.
+
endmenu
menu "SCSI low-level drivers"
depends on SCSI!=n
+config ISCSI_TCP
+ tristate "iSCSI Initiator over TCP/IP"
+ depends on SCSI && INET
+ select CRYPTO
+ select CRYPTO_MD5
+ select CRYPTO_CRC32C
+ select SCSI_ISCSI_ATTRS
+ help
+ The iSCSI Driver provides a host with the ability to access storage
+ through an IP network. The driver uses the iSCSI protocol to transport
+ SCSI requests and responses over a TCP/IP network between the host
+ (the "initiator") and "targets". Architecturally, the iSCSI driver
+ combines with the host's TCP/IP stack, network drivers, and Network
+ Interface Card (NIC) to provide the same functions as a SCSI or a
+ Fibre Channel (FC) adapter driver with a Host Bus Adapter (HBA).
+
+ To compile this driver as a module, choose M here: the
+ module will be called iscsi_tcp.
+
+ The userspace component needed to initialize the driver, documentation,
+ and sample configuration files can be found here:
+
+ http://linux-iscsi.sf.net
+
config SGIWD93_SCSI
tristate "SGI WD93C93 SCSI Driver"
depends on SGI_IP22 && SCSI
If unsure, say N.
-config SCSI_SATA_PROMISE
- tristate "Promise SATA TX2/TX4 support"
+config SCSI_PDC_ADMA
+ tristate "Pacific Digital ADMA support"
depends on SCSI_SATA && PCI
help
- This option enables support for Promise Serial ATA TX2/TX4.
+ This option enables support for Pacific Digital ADMA controllers
If unsure, say N.
If unsure, say N.
+config SCSI_SATA_PROMISE
+ tristate "Promise SATA TX2/TX4 support"
+ depends on SCSI_SATA && PCI
+ help
+ This option enables support for Promise Serial ATA TX2/TX4.
+
+ If unsure, say N.
+
config SCSI_SATA_SX4
tristate "Promise SATA SX4 support"
depends on SCSI_SATA && PCI && EXPERIMENTAL
If unsure, say N.
+config SCSI_SATA_SIL24
+ tristate "Silicon Image 3124/3132 SATA support"
+ depends on SCSI_SATA && PCI && EXPERIMENTAL
+ help
+ This option enables support for Silicon Image 3124/3132 Serial ATA.
+
+ If unsure, say N.
+
config SCSI_SATA_SIS
tristate "SiS 964/180 SATA support"
depends on SCSI_SATA && PCI && EXPERIMENTAL
If unsure, say N.
+config SCSI_SATA_INTEL_COMBINED
+ bool
+ depends on IDE=y && !BLK_DEV_IDE_SATA && (SCSI_SATA_AHCI || SCSI_ATA_PIIX)
+ default y
+
config SCSI_BUSLOGIC
tristate "BusLogic SCSI support"
depends on (PCI || ISA || MCA) && SCSI && ISA_DMA_API
substantial, so users of MultiMaster Host Adapters may wish to omit
it.
-#
-# This is marked broken because it uses over 4kB of stack in
-# just two routines:
-# 2076 CpqTsProcessIMQEntry
-# 2052 PeekIMQEntry
-#
-config SCSI_CPQFCTS
- tristate "Compaq Fibre Channel 64-bit/66Mhz HBA support"
- depends on PCI && SCSI && BROKEN
- help
- Say Y here to compile in support for the Compaq StorageWorks Fibre
- Channel 64-bit/66Mhz Host Bus Adapter.
-
config SCSI_DMX3191D
tristate "DMX3191D SCSI support"
depends on PCI && SCSI
To compile this driver as a module, choose M here: the
module will be called qlogicfas.
-config SCSI_QLOGIC_ISP
- tristate "Qlogic ISP SCSI support (old driver)"
- depends on PCI && SCSI && BROKEN
- ---help---
- This driver works for all QLogic PCI SCSI host adapters (IQ-PCI,
- IQ-PCI-10, IQ_PCI-D) except for the PCI-basic card. (This latter
- card is supported by the "AM53/79C974 PCI SCSI" driver.)
-
- If you say Y here, make sure to choose "BIOS" at the question "PCI
- access mode".
-
- Please read the file <file:Documentation/scsi/qlogicisp.txt>. You
- should also read the SCSI-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
- To compile this driver as a module, choose M here: the
- module will be called qlogicisp.
-
- These days the hardware is also supported by the more modern qla1280
- driver. In doubt use that one instead of qlogicisp.
-
config SCSI_QLOGIC_FC
tristate "Qlogic ISP FC SCSI support"
depends on PCI && SCSI
To compile this driver as a module, choose M here: the
module will be called qla1280.
-config SCSI_QLOGIC_1280_1040
- bool "Qlogic QLA 1020/1040 SCSI support"
- depends on SCSI_QLOGIC_1280 && SCSI_QLOGIC_ISP!=y
- help
- Say Y here if you have a QLogic ISP1020/1040 SCSI host adapter and
- do not want to use the old driver. This option enables support in
- the qla1280 driver for those host adapters.
-
config SCSI_QLOGICPTI
tristate "PTI Qlogic, ISP Driver"
depends on SBUS && SCSI